ESAB | Mig 4004i | Instruction manual | ESAB Mig 4004i User manual

ESAB Mig 4004i User manual
Mig 4004i, Mig 5004i
Instruction manual
0463 279 001 GB 20151211
Valid for: 145-xxx-xxxx, 211-xxx-xxxx
TABLE OF CONTENTS
1
SAFETY ................................................................................................................ 4
2
INTRODUCTION ................................................................................................... 7
2.1
Equipment............................................................................................................. 7
3
TECHNICAL DATA ............................................................................................... 8
4
INSTALLATION................................................................................................... 10
5
6
4.1
Location .............................................................................................................. 10
4.2
Lifting instruction............................................................................................... 10
4.3
Mains supply ...................................................................................................... 11
OPERATION ....................................................................................................... 14
5.1
Connections and control devices.....................................................................15
5.2
Symbols .............................................................................................................. 15
5.3
Connection of welding and return cable..........................................................15
5.4
Turning the power source on/off ......................................................................15
5.5
Fan control.......................................................................................................... 16
5.6
Overheating protection...................................................................................... 16
5.7
Remote control unit ........................................................................................... 16
5.8
VRD (Voltage Reducing Device) .......................................................................16
5.9
MIG/MAG and FCAW-S welding ........................................................................16
5.10
MMA welding ...................................................................................................... 16
MAINTENANCE .................................................................................................. 17
6.1
Inspection and cleaning .................................................................................... 17
6.2
Welding torch ..................................................................................................... 17
7
FAULT TRACING................................................................................................ 18
8
ORDERING OF SPARE PARTS ......................................................................... 19
DIAGRAM .................................................................................................................. 20
ORDERING NUMBERS .............................................................................................21
SPARE PARTS LIST..................................................................................................22
ACCESSORIES .........................................................................................................23
Rights reserved to alter specifications without notice.
0463 279 001
© ESAB AB 2015
1 SAFETY
1
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment when it
is started up
○ no-one is unprotected when the arc is struck or work is started with the equipment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could
become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Do not use the power source for thawing frozen pipes.
0463 279 001
-4-
© ESAB AB 2015
1 SAFETY
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting. Ask for your employer's safety practices which should
be based on manufacturers' hazard data.
ELECTRIC SHOCK - Can kill
•
•
•
•
Install and earth the unit in accordance with applicable standards
Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing
Insulate yourself from earth and the workpiece
Ensure your working stance is safe
FUMES AND GASES - Can be dangerous to health
•
•
Keep your head out of the fumes
Use ventilation, extraction at the arc, or both, to take fumes and gases away
from your breathing zone and the general area
ARC RAYS - Can injure eyes and burn skin
•
•
Protect your eyes and body. Use the correct welding screen and filter lens and
wear protective clothing
Protect bystanders with suitable screens or curtains
FIRE HAZARD
•
Sparks (spatter) can cause fire. Make sure therefore that there are no
inflammable materials nearby
NOISE - Excessive noise can damage hearing
•
•
Protect your ears. Use earmuffs or other hearing protection.
Warn bystanders of the risk
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
CAUTION!
Read and understand the instruction manual before
installing or operating.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of
class A equipment in those locations, due to conducted
as well as radiated disturbances.
0463 279 001
-5-
© ESAB AB 2015
1 SAFETY
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law, electrical
and/or electronic equipment that has reached the end of
its life must be disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
0463 279 001
-6-
© ESAB AB 2015
2 INTRODUCTION
2
INTRODUCTION
The Mig 4004i and Mig 5004i are welding power sources intended for MIG/MAG welding, as
well as for welding with powder filled cored wire (FCAW-S) and for welding with coated
electrodes (MMA).
The power sources are intended for use with the wire feed unit Feed 3004/4804.
ESAB's accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.1
Equipment
The power sources are supplied with:
•
•
•
5 m return cable with earth clamp
5 m mains cable with 32 Amp connector
instruction manual for the welding power source
0463 279 001
-7-
© ESAB AB 2015
3 TECHNICAL DATA
3
TECHNICAL DATA
Mig 4004i
Mig 5004i
Mains voltage
380-440 V, +/- 10%,
3~ 50/60 Hz
380-440 V, +/- 10%,
3~ 50/60 Hz
Mains supply Sscmin
1.8 MVA
2.2 MVA
Mains supply Zmax
-
0.22 Ω
Primary current I max
26 A
36 A
No-load power in energy-saving
mode 6.5 min. after welding
40 W
40 W
MIG/MAG
16 A/15 V - 400 A/34 V
16 A/15 V - 500 A/39 V
MMA
16 A/20 V - 400 A/36 V
16 A/21 V - 500 A/40 V
60 % duty cycle
400 A/34 V
500 A/40 V
80 % duty cycle
-
400 A/34 V
100% duty cycle
350 A/31.5 V
350 A/31.5 V
60 % duty cycle
400 A/36 V
500 A/40 V
80 % duty cycle
-
400 A/36 V
100% duty cycle
350 A/34 V
350 A/34 V
Setting range
Permissible load at MIG/MAG
Permissible load at MMA
Power factor at maximum current 0.93
0.95
Efficiency at maximum current
89 %
89 %
55 V
55 V
<35 V
<35 V
Operating temperature
-10 to +40°C
-10 to +40°C
Transportation temperature
-20 to +55°C
-20 to +55°C
Open-circuit voltage
VRD function inactivate1)
VRD function
active1)
Constant sound pressure when <70 db (A)
idling
<70 db (A)
Dimensions l × w × h
610 × 250 × 445 mm
610 × 250 × 445 mm
Weight
46 kg
46 kg
Insulation class
H
H
Enclosure class
IP 23
IP 23
Application class
1)
The VRD function is explained in chapter "VRD (Voltage Reducing Device)"
Mains supply, Ssc min
Minimum short circuit power on the network in accordance with IEC 61000-3-12.
Mains supply, Zmax
Maximum permissible line impedance of the network in accordance with IEC 61000-3-11.
0463 279 001
-8-
© ESAB AB 2015
3 TECHNICAL DATA
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 40°C / 104°F.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
0463 279 001
-9-
© ESAB AB 2015
4 INSTALLATION
4
INSTALLATION
The installation must be carried out by a professional.
CAUTION!
This product is intended for industrial use. In a domestic environment this product
may cause radio interference. It is the user's responsibility to take adequate
precautions.
4.1
Location
Position the welding power source such way that its cooling air inlets and outlets are not
obstructed.
4.2
0463 279 001
Lifting instruction
- 10 -
© ESAB AB 2015
4 INSTALLATION
4.3
Mains supply
NOTE!
Mains supply requirements
This equipment complies with IEC 61000-3-12 provided that the short-circuit
power is greater than or equal to Sscmin at the interface point between the user's
supply and the public system. It is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply with a short-circuit
power greater than or equal to Sscmin. Refer to the technical data in the
TECHNICAL DATA chapter.
0463 279 001
- 11 -
© ESAB AB 2015
4 INSTALLATION
NOTE!
The power source can be connected for generator power. For more information,
contact authorised ESAB service personnel.
Check that the unit is connected to the correct mains power supply voltage, and that it is
protected by the correct fuse size. A protective earth connection must be made, in
accordance with regulations.
A. Rating plate with supply connection data
Recommended fuse sizes and minimum cable areas
Mig 4004i
Mains voltage
Mains cable area
Mig 5004i
380-440V, +/- 10%, 3~50/60 Hz
4G4 mm2
4G6 mm2
21 A
27 A
Fuse anti-surge
25 A
35 A
Fuse Type C MCB-surge
32 A
32 A
Phase current Ieff Uin 400 V
19 A
26 A
Fuse anti-surge
20 A
35 A
Fuse Type C MCB-surge
32 A
32 A
Phase current Ieff Uin 440 V
18.5 A
24 A
Fuse anti-surge
20 A
25 A
Fuse Type C MCB-surge
32 A
32 A
Phase current Ieff Uin 380 V
NOTE!
The mains cable areas and fuse sizes as shown above are in accordance with
Swedish regulations. They may not be applicable in other countries: make sure
that the cable area and fuse sizes comply with the relevant national regulations.
0463 279 001
- 12 -
© ESAB AB 2015
4 INSTALLATION
Connection instruction
The power source is connected to 400V from factory. If another mains voltage is required, the
cable on the printed circuit board has to be moved and placed on the correct pin. See picture
above. This operation has to be made by persons who have appropriate electrical
knowledge.
Change of mains cable
If the mains cable needs to be changed, the earth connection to the bottom plate must be
made in a correct way. See from the picture above in which order the washers, nuts and
screws are placed.
0463 279 001
- 13 -
© ESAB AB 2015
5 OPERATION
5
OPERATION
General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!
WARNING!
Secure the equipment particularly if the ground is
uneven or sloping.
0463 279 001
- 14 -
© ESAB AB 2015
5 OPERATION
5.1
Connections and control devices
1. Mains power supply switch, 0 / 1
5. Connection (+): MIG/MAG: Welding cable
MMA: Welding cable or return cable
6. Connection (-): MIG/MAG: Return cable
MMA: Return cable or welding cable
7. Fuse for supply voltage for feeder unit
8. Mains cable
2. Connection for wire feed unit or remote
control unit
3. Indicating lamp, overheating
4. Indicating lamp, power supply ON
5.2
Symbols
Remote control unit (2)
Over heating (3)
Power supply ON (4)
5.3
Connection of welding and return cable
The power source has two outputs, a positive terminal (+) and a negative terminal (-), for
connecting welding and return cables. The output to which the welding cable is connected
depends on the welding method or type of electrode used.
Connect the return cable to the other output on the power source. Secure the return cable's
contact clamp to the work piece and ensure that there is good contact be tween the work
piece and the output for the return cable on the power source.
For MMA welding, the welding cable can be connected to the positive terminal (+) or
negative terminal (-) depending on the type of electrode used. The connecting polar ity is
stated on the electrode packaging.
5.4
Turning the power source on/off
Turn the power source on by turning switch (1) to the ”1” position. Turn the power source off
by turning the switch (1) to the ”0” position. Regardless the mains supply is interrupted
0463 279 001
- 15 -
© ESAB AB 2015
5 OPERATION
abnormally or the power source is switched off in the normal manner, the welding data will be
stored, so it will be available next time the unit is turned on.
5.5
Fan control
The power source has a time circuit, which keeps the fans running for 6.5 minutes after
welding has stopped, then the unit switches to energy-saving mode. The fans start again
when welding begins. The fans run at reduced speed for welding currents up to 200 A, and at
full speed for higher currents.
5.6
Overheating protection
The welding power source has overheating protection circuit that operates if the internal
temperature becomes too high. When this occurs the welding current is blocked and a fault
code is displayed on the control panel. The overheating protection resets automatically when
the temperature has fallen.
5.7
Remote control unit
The remote control unit must be connected to the remote control unit socket on the power
source before activation. When the remote control unit is activated, the panel on the wire
feed unit is inactive.
5.8
VRD (Voltage Reducing Device)
The VRD function ensures that the open-circuit voltage does not exceed 35V when welding
is not being carried out. This is indicated by a lit VRD LED on the panel.
The VRD function is blocked when the system senses that welding has started.
If the VRD function is activated and the open-circuit voltage exceeds the 35V limit, this is
indicated by an error message (16) appearing in the display and welding cannot be started
whilst the error message is displayed.
5.9
MIG/MAG and FCAW-S welding
An arc melts a continuously supplied wire. The weld pool is protected by shielding gas. For
MIG/MAG and FCAW-S welding, the power source is supplemented with:
•
•
•
•
wire feed unit
welding torch
connection cable between power source and wire feed unit
shielding gas bottle
5.10
MMA welding
MMA welding may also be referred to as welding with coated electrodes. Striking the arc
melts the electrode and its coating forms protective slag.
For welding with coated electrodes, the power source is supplemented with:
•
welding cable with electrode clamp.
0463 279 001
- 16 -
© ESAB AB 2015
6 MAINTENANCE
6
MAINTENANCE
NOTE!
Regular maintenance is important for safe, reliable operation.
Only those persons who have appropriate electrical knowledge (authorised personnel) may
remove the safety plates to connect or carry out service, maintenance or repair work on
welding equipment.
CAUTION!
All warranty undertakings from the supplier cease to apply if the customer
attempts any work to rectify any faults in the product during the warranty period.
6.1
Inspection and cleaning
Check regularly that the power source is free from dirt.
The power source should be regularly blown clean using dry compressed air at reduced
pressure. More frequently in dirty environments.
Otherwise the air inlet/outlet may become blocked and cause overheating. To avoid this, the
airfilter should be regularly cleaned.
Replacing and cleaning the dust filter:
1.
2.
3.
4.
Release the dust filter according to the figure.
Blow the filter clean with compressed air (reduced pressure).
Ensure that the filter with the finest mesh is placed towards the grille.
Reinstall the filter.
6.2
Welding torch
Wear parts should be cleaned and replaced at regular intervals in order to achieve
trouble-free welding.
0463 279 001
- 17 -
© ESAB AB 2015
7 FAULT TRACING
7
FAULT TRACING
Try these recommended checks and inspections before sending for an authorised service
technican.
Type of fault
No arc.
Actions
•
•
•
Welding current is interrupted during welding •
•
The thermal overload trips operate frequently •
•
Poor welding performance.
•
•
•
•
0463 279 001
- 18 -
Check that the mains power supply switch
is turned on.
Check that the welding current supply and
return cables are correctly connected.
Check that the correct current value is
set.
Check whether the thermal overload trip
has operated (indicated by the orange
lamp on the front)
Check the main power supply fuses.
Check to see whether the air filters are
clogged.
Make sure that you are not exceeding the
rated data for the power source (i.e. that
the unit is not being overloaded).
Check that the welding current supply and
return cables are correctly connected.
Check that the correct current value is
set.
Check that the correct welding wires are
being used.
Check the main power supply fuses.
© ESAB AB 2015
8 ORDERING OF SPARE PARTS
8
ORDERING OF SPARE PARTS
CAUTION!
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
Mig 4004i, Mig 5004i is designed and tested in accordance with the international and
European standards IEC/EN 60974-1 and IEC/EN 60974-10. It is the obligation of the
service unit which has carried out the service or repair work to make sure that the
product still conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the back cover of this
document. When ordering, please state product type, serial number, designation and spare
part number in accordance with the spare parts list. This facilitates dispatch and ensures
correct delivery.
0463 279 001
- 19 -
© ESAB AB 2015
DIAGRAM
DIAGRAM
0463 279 001
- 20 -
© ESAB AB 2015
ORDERING NUMBERS
ORDERING NUMBERS
Ordering number Denomination
Type
0465 154 880
Welding power source Mig 4004i
0465 155 880
Welding power source Mig 5004i
0459 839 071
Spare parts list
Mig 4004i, Mig 5004i
0740 800 217
Service manual
Mig 4004i, Mig 5004i
0462 305 001
Instruction manual
Cooling unit COOL 1
0444 408 101
Instruction manual
Feed unit Feed 3004/4804
Note
Instruction manuals in other languages can be downloaded from the Internet: www.esab.com
0463 279 001
- 21 -
© ESAB AB 2015
SPARE PARTS LIST
SPARE PARTS LIST
0463 279 001
Item
Ordering no.
Denomination
1
0462 197 001
Dust filter
- 22 -
© ESAB AB 2015
ACCESSORIES
ACCESSORIES
0462 151 880 Trolley
0459 839 039 Spare parts list for trolley
0460 565 880 Trolley
For use together with counter balance device
0461 310 880 Trolley adapter kit
For fitting of power sources Mig 4004i and
Mig 5004i to trolley 0460 565 880
0460 946 880 Stabilizer kit for counter balance (1)
0463 125 880 Trolley bracket
option when no cooling unit is assembled
Counter balance device
(includes mast and counter balance)
0458 705 880 for 300 mm bobbin
0458 705 882 for 440 mm bobbin
0463 279 001
- 23 -
© ESAB AB 2015
ACCESSORIES
0460 526 886 Feed 3004 U6
0460 526 887 Feed 3004 MA23
0460 526 896 Feed 3004 U6, with water
0460 526 897 Feed 3004 MA23, with water
0460 526 889 Feed 3004 MA24
0460 526 899 Feed 3004 MA24
0460 526 987 Feed 4804 MA23
0460 526 996 Feed 4804 U6, with water
0460 526 997 Feed 4804 MA23, with water
0460 526 989 Feed 4804 MA24
0460 526 999 Feed 4804 MA24, with water
0462 300 880 Cooling unit COOL 1
Connection set, 70 mm2 10 pole cable plug - 10 pole cable socket
0459 528 780 1.7 m
0459 528 781 5 m
0459 528 782 10 m
0459 528 783 15 m
0459 528 784 25 m
0459 528 785 35 m
Connection set water, 70 mm2 10 pole cable plug - 10 pole cable socket
0459 528 790 1.7 m
0459 528 791 5 m
0459 528 792 10 m
0459 528 793 15 m
0459 528 794 25 m
0459 528 795 35 m
Remote controls
0463 279 001
- 24 -
© ESAB AB 2015
ACCESSORIES
0459 491 880 Remote control unit MTA1 CAN
MIG/MAG: wire feed speed and voltage
MMA: current and arc force
TIG: current, pulse and background current
0459 491 883 Remote control unit AT1 CAN
MMA and TIG: current
0459 491 884 Remote control unit AT1 CF CAN
MMA and TIG: rough and fine setting of
current
Remote control cable 10 pole - 4 pole
0459 960 880 5 m
0459 960 881 10 m
0459 960 882 25 m
Information on PSF welding torches can be found in separate brochures.
For more information of the accessories contact the nearest ESAB agency.
0463 279 001
- 25 -
© ESAB AB 2015
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Heist-op-den-Berg
Tel: +32 15 25 79 30
Fax: +32 15 25 79 44
BULGARIA
ESAB Kft Representative Office
Sofia
Tel: +359 2 974 42 88
Fax: +359 2 974 42 88
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB International AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
www.esab.com
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
SOUTH AFRICA
ESAB Africa Welding & Cutting
Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
USA
ESAB Welding & Cutting
Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising