ESAB | PT 38 | Instruction manual | ESAB PT 38 User manual

ESAB PT 38 User manual
GB
PT-38
Instruction manual
0463 334 001 GB 20120618
-2-
1
2
3
4
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4
5
6
6
Cutting with the PT-38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stand-off guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drag cutting 40 Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gouging with the PT-38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cut data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation of power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
8
8
9
9
10
10
5 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WIRE DIMENSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDER NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
12
15
16
18
Rights reserved to alter specifications without notice.
TOCe
-3-
GB
1
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be ob­
served in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equip­
ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in­
jury to the operator and damage to the equipment.
1.
Anyone who uses the equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding and cutting
2.
The operator must ensure that:
S no unauthorised person is stationed within the working area of the equipment when it is
started up.
S no-one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves.
S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
WARNING
Welding and plasma cutting can be injurious to yourself and others. Take
precautions when welding or cutting. Ask for your employer's safety practices
which should be based on manufacturers' hazard data.
-4bg21e
© ESAB AB 2012
GB
WARNING
Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
S
Install and earth the unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION
Read and understand the instruction manual before
installing or operating.
CAUTION
This product is solely intended for plasma cutting.
ESAB can provide you with all necessary welding protection and accessories.
2
INTRODUCTION
The PT-38 is a manual torch with a 90° head designed for use with several plasma
arc cutting packages using clean, dry air as the plasma gas. The service line lengths
available with the PT-38 torch are 7.6 m and 15.2 m. The PT-38 torch is rated to
operate at a maximum of 90 amperes at 100% duty cycle.
This manual is intended to provide the operator with all the information required to
assemble, operate, and repair the PT-38 Plasma Arc Cutting Torch. For additional
safety precautions, process instructions, and system troubleshooting; refer to the
appropriate instruction manual for your Plasma Arc Cutting Package.
ESAB's accessories for the product can be found on page 18.
-5bg21e
© ESAB AB 2012
GB
S
Excellent cutting capacity - Cuts 38 mm; severs 45 mm
S
Uses work air or cylinder air for superior versatility
S
Pilot arc starting - even starts through paint
S
Choice of 7.6 m. or 15.2 m line length
3
TECHNICAL DATA
PT-38
Cuts
38 mm; severs 45 mm
Current capacity
90 amps at 100% duty cycle
Nominal flow rate
189 l/min at 5.5 bar
Length of service lines
7.6 m or 15.2 m
Dimensions
Overall length
Length of head
208 mm
76 mm
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at
a certain load without overloading. The duty cycle is valid for 40° C.
Torches and torch body assemblies are supplied without gas baffle, electrode,
nozzle, and retaining/shield cup. Order complete spare parts kits or individual
components see spare parts list.
4
OPERATION
General safety regulations for handling the equipment can be found on
page 4. Read through before you start using the equipment!
4.1
Cutting with the PT-38
Use the following procedures to cut with the PT-38 torch.
1. Make sure that the wall power supply switch is on. Turn on the Power to the
cutting power source console.
2. Set Pressure Regulator to 5.5 bar.
3. Powercut 1600: Hold the torch nozzle approximately 3.2 mm - 6.4 mm above
the work and tilted at about 5 - 15°. This reduces the chance of spatter entering
the nozzle. If the PT 38's 90A standoff guide is being used, the distance between
nozzle and work piece will be approximately 6.4 mm.
Powercut 900: Hold the torch nozzle approximately 3.2 mm - 4.8 mm above the
work and tilted at about 5 - 15°. This reduces the chance of spatter entering the
nozzle. If the PT 38's 60A standoff guide is being used, the distance between
nozzle and work piece will be approximately 3.2 mm.
4. Depress the torch switch. Air should flow from the torch nozzle.
5. Two seconds after depressing the torch switch, the pilot arc should start. The
main arc should immediately follow, allowing the cut to begin. If using the trigger
LOCK mode, torch switch may be released after establishing the cutting arc.
-6bg21e
© ESAB AB 2012
GB
6. After starting the cut, the torch should be held at a 5 - 15° forward angle. This
angle is especially useful in helping to create a "drop" cut. When not using the
standoff guide, the nozzle should be held approximately, PC-1300/1600: 3.2 mm
- 6.4 mm, PC-900: 3.2 mm - 4.8 mm from the work.
PC 900, PC 1600
PC 1600
PC 900
Proper torch angle
Stand-off vs. Power output
WARNING
Arc rays can burn eyes and skin; noise can damage hearing.
-Wear a welding helmet with no. 6 or 7 lens shade.
-Wear eye, ear, and body protection.
Piercing and cutting techniques using the PT-38.
-7bg21e
© ESAB AB 2012
GB
4.2
Stand-off guide
A: Guide against straight edge or free-hand cut.
Use to maintain a constant stand-off distance. Attach optional stand-off guide
assembly by removing the retaining/shield cup (B) and installing the stand-off guide
assembly (C).
Installation and operation of stand-off guide
4.3
Drag cutting 40 Amp
For cutting thin material, under 9 mm, insert low current gas baffle, electrode, 40
amp drag nozzle, and standard retaining/shield cup. Set current level to 40 amps
and begin cutting.
A: Gas baffle (30-70 Amp)
C: 40 Amp Drag nozzle
B: Electrode
D: Retaining/ shield cup.
-8bg21e
© ESAB AB 2012
GB
4.4
Gouging with the PT-38
Powercut 1600: Insert high current gas baffle, electrode, 90 amp gouge nozzle, and
90 amp gouging heatshield assembly. Operating parameters are 4.1 - 5.5 bar and
70 - 90 amps. Air pressure and current can be varied within these ranges to produce
desired metal removal rate and groove profile.
Powercut 900: Insert standard gas baffle, electrode, 60 amp gouge nozzle, and 60
amp gouging heatshield assembly. Operating parameters are 4.1 - 5.5 bar and
40 - 60 amps. Air pressure and current can be varied within these ranges to produce
desired metal removal rate and groove profile.
A: Gas baffle 90 Amp- PC 1600
D: Gouging heatshield assembly
90 Amp- PC 1600, 60 Amp- PC 900
B: Electrode
E: Gas baffle 60 Amp- PC 900.
C: Gouge nozzle 90 Amp- PC 1600,
60 Amp- PC 900
4.5
Installing consumables
Tests have shown that with proper use of the torch, within the rated operating
conditions (especially arc current and gas flow rate), consumable parts do not
become loose if they are firmly installed. Torch damage and overheating can be
caused by loose parts.
1. Tighten the electrode and retaining/shield cup fully at each consumable change
or inspection.
2. Check consumable tightness at beginning of each work period, even if
everything was working normally at the end of the previous period.
Note: Ensure that the electrode/torch body seat and piston are clean and free of
dust or dirt. Debris may prevent mating surfaces from having solid contact.
Note: Firm tightening of the electrode by hand is sufficient; the use of tools such as
wrenches or pliers is not required or recommended.
Note: Torch damage and overheating can be caused by loose parts. Arc tracking
indicates loose parts. Make sure the retaining cup is tightened fully. Parts damaged
by arcing will cause greater damage to the torch and must be replaced.
-9bg21e
© ESAB AB 2012
GB
A: Nozzle
E: Piston
B: Retaining/ shield cup
F: Electrode/ torch body seat
C: Electrode
G: Torch body assembly
D: Gas baffle (90A)
H: Gas baffle (30-70A).
Information regarding wear parts, see page 16.
4.6
Cut data
Information regarding cut data, see “wire dimensions” on page 12.
4.7
Operation of power source
For operation of the power source, refer to Powercut 900, Powercut 1600 power
source instruction manual.
5
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
IMPORTANT! Switch off the power source when cleaning the torch.
CAUTION
All guarantee undertakings from the supplier cease to apply if the customer attempts any
work to rectify any faults in the product during the guarantee period.
6
ORDERING NUMBER
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
PT-38 is designed and tested in accordance with the international and European stan­
dards EN 60974-7, . It is the obligation of the service unit which has carried out the
service or repair work to make sure that the product still conforms to the said stan­
dard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
- 10 bg21e
© ESAB AB 2012
NOTES
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
- 11 notes
PT-38
Wire dimension
PT-38, Powercut 1600, Plasma system process data
Description
Ordering number
Electrode
0558 005 220
Nozzle
0558 007 682
Gas baffle
0558 004 870
Retaining/ shield cup
0558 008 094
40 Amperes, carbon steel
Material
thickness
mm
1.5
3.2
6.4
12.7
Stand-off
Initial height
mm
1.5- 3.2
1.5- 3.2
1.5- 3.2
1.5- 3.2
Air pressure
Bar
5.5
5.5
5.5
5.5
Travel speed
m/min
9.1
4.8
1.5
0.4
40 Amperes, aluminium
Material
thickness
mm
1.5
3.2
6.4
12.7
Stand-off
Initial height
mm
1.5- 3.2
1.5- 3.2
1.5- 3.2
1.5- 3.2
Air pressure
Bar
5.5
5.5
5.5
5.5
Travel speed
m/min
9.5
3.8
1.2
0.4
40 Amperes, stainless steel
Material
thickness
mm
1.5
3.2
6.4
12.7
Stand-off
Initial height
mm
1.5- 3.2
1.5- 3.2
1.5- 3.2
1.5- 3.2
Air pressure
Bar
5.5
5.5
5.5
5.5
Travel speed
m/min
8.9
3.3
0.6
0.2
- 12 bg21wi
© ESAB AB 2012
PT-38
PT-38, Powercut 900, Plasma system process data
Description
Ordering number
Electrode
0558 005 220
Nozzle
0558 008 417
Gas baffle
0558 005 217
Retaining/ shield cup
0558 008 094
60 Amperes, carbon steel
Material
thickness
mm
6.4
12.7
19.1
25.4
Stand-off
Initial height
mm
3.2
3.2
3.2
3.2
Air pressure
Bar
5.5
5.5
5.5
5.5
Travel speed
m/min
2.9
0.8
0.4
0.2
60 Amperes, aluminium
Material
thickness
mm
6.4
12.7
19.1
25.4
Stand-off
Initial height
mm
4.78
4.78
4.78
4.78
Air pressure
Bar
5.5
5.5
5.5
5.5
Travel speed
m/min
2.6
1.1
0.4
0.3
60 Amperes, stainless steel
Material
thickness
mm
6.4
12.7
19.1
25.4
Stand-off
Initial height
mm
4.78
4.78
4.78
4.78
Air pressure
Bar
5.5
5.5
5.5
5.5
Travel speed
m/min
2.0
0.6
0.3
0.1
- 13 bg21wi
© ESAB AB 2012
PT-38
PT-38, Powercut 1600, Plasma system process data
Description
Ordering number
Electrode
0558 005 220
Nozzle
0558 007 680
Gas baffle
0558 004 870
Retaining/ shield cup
0558 008 094
90 Amperes, carbon steel
Material
thickness
mm
6.4
12.7
19.1
25.4
38.1
Stand-off
Initial height
mm
3.8
3.8
3.8
3.8
3.8
Air
pressure
Bar
5.5
5.5
5.5
5.5
5.5
Travel
speed
m/min
4.0
1.5
0.7
0.4
0.2
90 Amperes, aluminium
Material
thickness
mm
6.4
12.7
19.1
25.4
38.1
Stand-off
Initial height
mm
6.4
6.4
6.4
6.4
6.4
Air
pressure
Bar
5.5
5.5
5.5
5.5
5.5
Travel
speed
m/min
4.7
1.9
1.3
0.6
0.3
90 Amperes, stainless steel
Material
thickness
mm
6.4
12.7
19.1
25.4
38.1
Stand-off
Initial height
mm
3.8
3.8
6.4
6.4
6.4
Air
pressure
Bar
5.5
5.5
5.5
5.5
5.5
Travel
speed
m/min
3.2
1.2
0.7
0.3
0.2
- 14 bg21wi
© ESAB AB 2012
PT-38
Order number
Ordering no.
Denomination
Type
Notes
0558 006 786 PT-38 torch
7.6m (25')
0558 006 787 PT-38 torch
15.2m (50')
0449 551 001 Instruction manual
0449 549 001 Instruction manual
Powercut™ 1300/1600 CE
Powercut™ 900 CE
0558 007 235 Power source for manual
plasma cutting incl torch
Powercut™ 1600 CE +
PT-38
400 V
0558 007 234 Power source for manual
plasma cutting
Powercut™ 1600 CE
400 V
0558 008 123 Power source for plasma
cutting
Powercut™ 900 CE
230 V
0558 008 124 Power source for plasma
cutting and torch
Powercut™ 900 CE+
PT-38
230 V
0558 008 135 Power source for plasma
cutting
Powercut™ 900 CE
400 V
0558 008 136 Power source for plasma
cutting and torch
Powercut™ 900 CE+
PT-38
400 V
Technical documentation is available on the Internet at www.esab.com
- 15 bg21o
© ESAB AB 2012
PT-38
Wear parts
Consumables breakdown PC1600
Consumables breakdown PC900
- 16 bg21we
© ESAB AB 2012
PT-38
Wear parts kits
0558 007 640 0558 008 419
90 Amp
60 Amp
PC 1600
PC 900
Ordering number
Denomination
3
3
0558 005 220
Electrode
1
1
0558 005 217
Gas baffle 30-70A
1
-
0558 004 870
Gas baffle 90/100A
-
3
0558 008 417
Nozzle 60 Amp
-
-
0558 005 219
Nozzle 70 Amp
4
-
0558 007 680
Nozzle 90 Amp
1
-
0558 007 682
Nozzle drag 40 Amp
1
1
0558 008 094
Retaining/ shield cup long
3
3
0558 101 101
O-ring .301ID .070W Nitrile
1
1
0558 004 443
Grease silicon dow DC-111 (1/4 oz)
1
1
0558 001 379
Fuse midget slo-blo 2A 600V
- 17 bg21we
© ESAB AB 2012
PT-38
Accessories
Gas flow measuring kit
0558 000 739
Valuable troubleshooting tool
allows measurement of the
actual air flow through the torch.
Torch guide kit
This complete kit, in a rugged
plastic carrying case, includes
attachments for circle and
straight line cutting on ferrous
and non-ferrous metals.
Deluxe, 44.5mm- 106cm radius
Basic, 44.5mm- 71cm radius
0558 003 258
0558 002 675
Extra bushing for guide kits
0558 003 257
Leather sheath protection
7.6 m
0558 002 921
Leather sheath protection
15 m
0558 002 922
Powercut 1600
Stand-off guide assembly 90
Amp
Use to maintain constant
stand-off distance.
0558 006 614
O-ring for blue body
0558 000 734
Gouging 90 Amp
-Gouging nozzle 90 Amp
-Gouging heat shield assembly
90 Amp
-*Note: Must use 90/100 Amp
gas baffle.
0558 007 681
0558 008 186
0558 004 870
- 18 bg21a
© ESAB AB 2012
PT-38
Wear parts kit PT-38, 90 Amp
0558 007 640
Powercut 1300
Wear parts kit PT-38, 70 Amp
0558 007 642
Powercut 900
Stand- off guide assembly
60 Amp
Use to maintain constant
stand-off distance.
0558 008 592
O-ring for blue body
0558 000 734
Gouging 60 Amp
-Gouging nozzle 60 Amp
-Gouging heat shield assembly
60 Amp
0558 008 588
0558 008 591
Wear parts kit PT-38, 60 Amp
0558 008 419
- 19 bg21a
© ESAB AB 2012
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
BULGARIA
ESAB Kft Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
SOUTH AFRICA
ESAB Africa Welding & Cutting Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
www.esab.com
© ESAB AB
110915
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising