ESAB | Mig C250 3ph | Instruction manual | ESAB Mig C250 3ph User manual

ESAB Mig C250 3ph User manual
GB
Origo™
Mig C170 3ph
Mig C200 3ph
Mig C250 3ph
Instruction manual
0463 344 001 GB 20120612
Valid for serial no. 626-xxx-xxxx
-2-
1 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
4
6
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
3 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
7
4.1
4.2
4.3
4.4
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mains power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1
5.2
5.3
5.4
5.5
7
8
8
9
9
Connection and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welding without gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire feed pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing and inserting wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
11
11
11
12
6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
6.1
Inspection and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
7 FAULT TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 ORDERING OF SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDER NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
18
19
20
Rights reserved to alter specifications without notice.
TOCe
-3-
GB
1
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be ob­
served in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equip­
ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in­
jury to the operator and damage to the equipment.
1.
Anyone who uses the equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding and cutting
2.
The operator must ensure that:
S no unauthorised person is stationed within the working area of the equipment when it is
started up.
S no-one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves.
S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
WARNING
Do not use the power source for thawing frozen pipes.
-4ba46e
GB
WARNING
Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
S
Install and earth the unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION
Read and understand the instruction manual before
installing or operating.
CAUTION
This product is solely intended for arc welding.
CAUTION
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
-5ba46e
GB
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
2
INTRODUCTION
Mig C170 3ph, Mig C200 3ph and Mig C250 3ph are step controlled power
sources of a compact design, intended for welding with solid steel, stainless steel or
aluminium wire as well as tubular wire with or without shielding gas. It is possible to
weld with homogeneous wire/shielding gas and weld with gasless tubular wire by
switching the + and - connections on the switching terminal by the wire feed unit.
ESAB's accessories for the product can be found on page 20.
2.1
Equipment
The power source is supplied with:
S
Welding gun
S
Return cable with return clamp
S
Shelf for gas cylinder
S
Instruction manual
3
TECHNICAL DATA
Mig C170 3ph
Mig C200 3ph
Mig C250 3ph
400-415V,
3∼ 50/60 Hz
400-415V,
3∼ 50/60 Hz
230/400-415V,
3∼ 50/60 Hz
Permissible load at
100% duty cycle
100A
120A
150A
60 % duty cycle
130A
150A
190A
35 % duty cycle
170A
200A
250A
Setting range (DC)
30-170A
30-200A
40-280A
Open circuit voltage
15.5-30.6V
16.0-31.8V
15.0-37.0V
Open circuit power
310W
210W
340W
Power factor at max load
0.97
0.97
0.97
Control voltage
42V, 50/60Hz
42V, 50/60Hz
42V, 50/60Hz
Wire feed speed
1.0-17m/min
1.0-17m/min
1.0-17m/min
Burnback time
0.02-0.25s
0.02-0.25s
0.02-0.25s
Voltage
-6ba46e
GB
Mig C170 3ph
Mig C200 3ph
Mig C250 3ph
Spot welding
0.2-2.5s
0.2-2,5s
0.2-2.5s
Welding gun connection
EURO
EURO
EURO
Wire dimension range
0.6-0.8(Fe, SS)
1.0(Al)
0.8(FCW)
0.8-1.0(CuSi)
0.6-1.0(Fe, SS)
1.0(Al)
0.8-1.0(FCW)
0.8-1.0(CuSi)
0.6-1.2(Fe, SS)
1.0-1.2(Al)
0.8-1.2(FCW)
0.8-1.0(CuSi)
Max diameter / weight of
wire bobin
300mm/15kg
300mm/15kg
300mm/15kg
Dimensions lxwxh
860x420x730
860x420x730
860x420x730
Weight
63.5kg
72.5kg
82kg
Operating temperature
-10 ÷ +40°C
-10 ÷ +40°C
-10 ÷ +40°C
Transportation temperature -20 ÷ +55°C
-20 ÷ +55°C
-20 ÷ +55°C
Enclosure class
IP 23
IP 23
IP 23
Application classification
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at
a certain load without overloading. The duty cycle is valid for 40° C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
4
INSTALLATION
The installation must be carried out by a professional.
Note!
Connect the power source to the electricity mains with a network impedance of 0.268 (C250 3ph) ohm
or lower. If the network impedance is higher, there is a risk of flicker in the illuminators.
CAUTION
This product is intended for industrial use. In a domestic environment this product may
cause radio interference. It is the user's responsibility to take adequate precautions.
4.1
Location
Position the welding power source in such way that its cooling air inlets and outlets
are not obstructed.
-7ba46e
GB
4.2
Assembly of components
WARNING
For packing and shipment of the machine the wheels are detached from the unit.
Before use attach the wheels according to instruction.
1.
2.
3.
4.3
Electrical installation
C200 3ph
-8ba46e
GB
4.4
Mains power supply
Check that the unit is connected to the correct mains power supply voltage, and that
it is protected by the correct fuse size. A protective earth connection must be made,
in accordance with regulations.
Rating plate with supply connection data
Recommended fuse sizes and minimum cable area
Mig C170 3ph
Mig C200 3ph
Mig C250 3ph
400-415V,
3∼ 50/60 Hz
400-415V,
3∼ 50/60 Hz
230 / 400-415V,
3∼ 50/60 Hz
Current A
at 100% duty cycle
4.0
5.3
12.1/7.0
at 60% duty cycle
6.1
6.8
17.6/10.2
8.9
10.1
25.3/14.6
4 x 1.5
4 x 1.5
4 x 2.5 / 4 x 1.5
10
10
25/16
Voltage V
at 35% duty cycle
Mains Cable area
mm2
Fuse slow A
NB: The mains cable areas and fuse sizes shown above are in accordance with Swedish regulations.
They may not be applicable in other countries: make sure that the cable area and fuse sizes comply
with the relevant national regulations.
5
OPERATION
General safety regulations for handling the equipment can be found on
page 4. Read through before you start using the equipment!
WARNING
Rotating parts can cause injury, take great care.
WARNING
To prevent the reel from sliding off the hub: Lock the
reel in place by turning the red knob as shown on the
warning label attached next to the hub.
-9ba46e
GB
WARNING
Secure the equipment - particularly if the
ground is uneven or sloping.
5.1
Connection and control devices
1
Mains supply switch
7
Connection for return cable (-), low inductance
2
Indicator lamp, power ON/OFF
8
Knob for spot welding - ON/OFF and time
setting
3
4
5
6
Orange indicator lamp, overheating
Welding voltage switch
EURO - connector for welding gun
Connection for return cable (-), high
inductance
9
10
11
*
Knob for wire speed setting
Digital instrument - V/A (option,see page 20)
Return cable with return clamp
Knob for burn-back time setting (located on
control board)
C170 3ph
C200 3ph
C250 3ph
- 10 ba46e
GB
5.2
Welding without gas
5.3
Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then
set the pressure of the wire feeder's pressure rollers. It is important that the
pressure is not too great.
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
Fig 1
Fig 2
To check that the feed pressure is set correctly, you can feed out the wire against
an insulated object, e.g. a piece of wood.
When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed
rollers should slip.
If you hold the gun approx. 50 mm from the piece of wood, the wire should be
fed out and bend (fig. 2).
5.4
Replacing and inserting wire
S
Open the side panel.
S
Disconnect the pressure sensor by folding it backwards, the pressure rollers
slide up.
- 11 ba46e
GB
S
S
S
S
Straighten the new wire for 10-20 cm. File away burrs and sharp edges from the
end of the wire before inserting it into the wire feed unit.
Make sure that the wire goes properly into the feed roller track and into the outlet
nozzle and the wire guide.
Secure the pressure sensor.
Close the side panel.
5.5
Overheating protection
When the machine is switched on with the mains switch [1], indicator lamp [2] is on and
lamp [3] off - the machine is ready to operate. If the internal temperature becomes too
high, the welding is interrupted and disabled. This state is indicated by lighting of the
orange indicator lamp [3] on the front of the machine. It resets automatically when the
temperature has fallen.
6
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
CAUTION
All guarantee undertakings from the supplier cease to apply if the customer attempts any
work to rectify any faults in the product during the guarantee period.
6.1
Inspection and cleaning
Check regularly that the power source is free from dirt.
The power source should be regularly blown clean using dry compressed air at reduced
pressure. It should be cleaned more frequently in dirty environments. Otherwise the air
inlet/outlet may become blocked and cause overheating.
Welding gun
S
The welding gun's wear parts should be cleaned and replaced at regular
intervals in order to achieve trouble-free wire feed. Blow the wire guide clean
regularly and clean the contact tip.
The brake hub
The hub is adjusted when delivered, if
readjustment is required, follow the instructions
below. Adjust the brake hub so that wire is slightly
slack when wire feed stops.
S
Adjusting the braking torque:
S
Turn the red handle to the locked position.
S
Insert a screwdriver into the springs in the hub.
Turn the springs clockwise to reduce the braking torque
Turn the springs counter-clockwise to increase the braking torque. NB: Turn
both springs the same amount.
- 12 ba46e
GB
7
FAULT TRACING
Try these recommended checks and inspections before sending for an authorised
service technican.
Type of fault
Actions
S
S
No arc
S
Welding current is interrupted
during welding
S
S
Check that the mains power supply switch is turned on.
Check that the welding current supply and return cables are
correctly connected.
Check that correct current value is set.
Check whether the thermal overload trip has operated
(indicated by the orange lamp on the front).
Check the main power supply fuses.
Thermal overload trips
operate frequently
S
S
Check to see whether the air inlets/outlets are clogged.
Make sure that you are not exceeding the rated data for the
power source (i.e. that the unit is not being overloaded).
Poor welding performance
S
Check that the welding current supply and return cables are
correctly connected.
Check that the correct current value is set.
Check that the correct welding wires are being used.
Check the main power supply fuses.
Check the wire feed unit - if proper rolls are applied and
properly set the pressure of the wire feeder's pressure rollers
S
S
S
S
8
ORDERING OF SPARE PARTS
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
Mig C170 3ph, Mig C200 3ph, Mig C250 3ph is designed and tested in accordance with the
international and European standards IEC-/ EN 60974-1, IEC-/ EN 60974-10. It is the obliga­
tion of the service unit which has carried out the service or repair work to make sure that the
product still conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
- 13 ba46e
Diagram
Mig C170 3ph, 400-415V
- 14 ba46e
© ESAB AB 2012
Mig C200 3ph, 400-415V
- 15 ba46e
© ESAB AB 2012
Mig C250 3ph, 400-415V
- 16 ba46e
© ESAB AB 2012
Mig C250 3ph, 230/400-415V
- 17 ba46e
© ESAB AB 2012
Mig C170 3ph, Mig C200 3ph, Mig C250 3ph
Order number
Ordering no.
Denomination
Type
Notes
0349 308 670 Power source
OrigoTM Mig C170 3ph
400-415V 3~50/60Hz
0349 308 290 Power source
OrigoTM Mig C200 3ph
400-415V 3~50/60Hz
0349 307 840 Power source
OrigoTM Mig C250 3ph
400-415V 3~50/60Hz
0349 309 090 Power source
OrigoTM Mig C250 3ph
230/400-415V 3~50/60Hz
0349 300 524 Spare parts list
Mig C170 3ph,
Mig C200 3ph,
Mig C250 3ph
Technical documentation is available on the Internet at www.esab.com
- 18 ba46o
© ESAB AB 2012
Mig C170 3ph, Mig C200 3ph, Mig C250 3ph
Wear parts
(W. F. Mechanism 0455 890 890)
Item
Denomination
Ordering no.
A
Pressure roller
0455 907 001
B
Feed roller
0367 556 001
0367 556 002
0367 556 003
0367 556 004
C
Inlet nozzle
0466 074 001
D
Insert tube
0455 894 001
0455 889 001
0455 885 001
E
Outlet nozzle
0455 886 001
Notes
Ø 0.6-0.8mm Fe, Ss, cored wire.
Ø 0.8-1.0mm Fe, Ss, cored wire.
Ø 1.0-1.2mm Fe, Ss, cored wire.
Ø 1.0-1.2mm Al wire.
Plastic, must be used together with item 0455 885 001,
for welding with Al wire.
Steel, must be used together with item 0455 886 001.
Must be used together with item 0455 894 001,
for welding with Al wire.
Must be used together with item 0455 889 001.
The rollers are marked with wire dimension in mm, some are also marked with inch.
Welding with aluminium wires.
In order to weld with aluminium wires, proper rollers, nozzles and liners for aluminium wires MUST be
used. It is recommended to use 3m long welding gun for aluminium wires, equipped with appropriate
wear parts.
- 19 ba46w
© ESAB AB 2012
Mig C170 3ph, Mig C200 3ph, Mig C250 3ph
Accessories
Digital meter . . . . . . . . . . . . . . . . . .
0349 302 598
Transformer kit for CO2 heater . . . . . . . . . . .
0349 302 250
Polarity change KIT . . . . . . . . . . . . . . . . . . . . .
0349 309 310
- 20 ba46a
© ESAB AB 2012
- 21 ba46hints
- 22 ba46hints
- 23 ba46hints
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
BULGARIA
ESAB Kft Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
SOUTH AFRICA
ESAB Africa Welding & Cutting Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
www.esab.com
© ESAB AB
110915
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising