ESAB | MechTig C2002i Aristo MechTig C2002i | Instruction manual | ESAB MechTig C2002i Aristo MechTig C2002i User manual

ESAB MechTig C2002i Aristo MechTig C2002i User manual
GB
MechTig C2002i
Aristot
Instruction manual
0444 620 001 GB 070605
Valid for serial no. 652--xxx--xxxx
1 DIRECTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
5
3.1 Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Control panel WO 100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
4 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
5.1
5.2
5.3
5.4
Lifting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mains power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the terminating resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
7
7
6 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
Connections and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas flow meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow guard, water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow guard, gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbol explanations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
9
9
9
9
9
9
7 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.1 Inspection and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2 Topping up the coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
11
8 FAULT--TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 ORDERING SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PUMP DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING CARACTERISTIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
12
14
18
19
20
21
Rights reserved to alter specifications without notice.
TOCe
-- 2 --
GB
1
DIRECTIVE
DECLARATION OF CONFORMITY
ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that welding power source MechTig C2002i from serial number 652 (2006 w.52) are constructed and tested in
compliance with the standard EN 60974--1 /--2 /--3 /--5 and EN 60974--10 in accordance with the requirements of directive (2006/95EC) and (2004/108/EEC).
-------------------------------------------------------------------------------------------------------------------------------------Laxå 2006--12--15
Kent Eimbrodt
Global Director
Equipment and Automation
2
SAFETY
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1.
Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no--one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves.
S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
dp02d1ea
-- 3 --
GB
WARNING
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S
Install and earth the welding unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS -- Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding protection and accessories.
WARNING!
Read and understand the instruction manual before installing
or operating.
WARNING!
Do not use the power source for thawing frozen pipes.
This product is solely intended for arc welding.
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and returned to an
environmentally compatible recycling facility. As the owner of the equipment, you should
get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human health!
dp02d1ea
-- 4 --
GB
3
INTRODUCTION
MechTig C2002i is a welding power source intended for mechanized TIG welding.
ESAB’s accessories for the product can be found on page 21.
3.1
Equipment
The power source is supplied with:
S
instruction manual for the welding power source
S
instruction manual for the control panel
S
5 m return cable
S
terminating resistor.
3.2
Control panel WO 100
See the separate instruction manual for a detailed description of the control panel.
4
TECHNICAL DATA
MechTig C2002i
Mains voltage
230 V, ±10%, 1∼ 50/60 Hz
Primary current Imax
34 A
Setting range
4 A -- 200 A
Permitted load
25% duty cycle
35% duty cycle
60 % duty cycle
100% duty cycle
200 A / 18 V
180 A / 17 V
140 A / 15.5 V
110 A / 14.5 V
Power factor at maximum current
0,62
Efficiency at maximum current
75 %
Open--circuit voltage
71 -- 78 V
Operating temperature
--10 to +40˚C
Transportation temperature
--25 to + 55˚C
Constant A--weighted sound pressure
< 70 dB
dp02d1ea
-- 5 --
GB
MechTig C2002i
Dimensions l x w x h
470 x 479 x 472 mm
Weight
30 kg
Enclosure class
Application class
IP 23
Cooling unit
Cooling power
at 50 Hz
at 60 Hz
670 W at 40˚C temp. difference and flow 1.0 l/min
650 W at 40˚C temp. difference and flow 1.0 l/min
Type of cooling
50 % water / 50% monoethylene glycol
Coolant quantity
2.0 l
Maximum water flow
at 50 Hz
at 60 Hz
1.22 l/min
1.44 l/min
Maximum water pressure
at 50 Hz
at 60 Hz
0.32 MPa (3.2 bar)
0.42 MPa (4.2 bar)
Duty cycle
The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a certain load without overloading.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
5
INSTALLATION
The installation must be executed by a professional.
WARNING!
This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’s responsibility to take adequate precautions.
dp02d1ea
-- 6 --
GB
5.1
Lifting instructions
5.2
Location
Position the welding power source such that its cooling air inlets and outlets are not
obstructed.
5.3
Mains power supply
Make sure that the welding power source is connected to the correct supply voltage
and that it is protected by the correct fuse rating. A protective earth connection must
be made in accordance with regulations.
Recommended fuse sizes and minimum cable area
MechTig C2002i
Mains voltage
Mains cable area
Phase current I RMS
Fuse
anti--surge
type C MCB
230 V 1 μ 50/60 Hz
3 G 2.5 mm2
17.2 A
20 A
25 A
Welding cable area
25 mm2
NOTE! The mains cable areas and fuse sizes as shown above are in accordance with Swedish
regulations. Use the welding power source in accordance with the relevant national regulations.
5.4
Connecting the terminating resistor
To avoid communication interference, the remote socket must be fitted with a
terminating resistor, when a remote control unit is not connected.
dp02d1ea
-- 7 --
GB
6
OPERATION
General safety regulations for the handling of the equipment can be found on
page 3. Read through before you start using the equipment!
6.1
Connections and control devices
1
Connection for start gas in
2
Connection for weld gas in
3
Connection for root gas in
4
Switch for mains power
5
Rating plate for connection data
6
Control panel,
see separate instruction manual
7
Gas flow meter
8
Printer
9
USB connection, see point 6.3.
10
Connection for documentation system
WMS 4000
11
Connection (CAN) for remote control unit,
terminating resistor or welding station A25
12
Connection for wire feed
13
Root gas connection out
14
Weld and start gas connection out
15
Connection for rotation
16
Connection for coolant from tube welding
tool RED
17
Connection with ELP* for coolant to the
tube welding tool BLUE
18
Topping up with coolant
19
Connection for welding current (--)
20
Connection for manual TIG torch
21
Return cable connection (+)
*ELP = ESAB Logic Pump, see point 6.4.
6.2
Gas flow meter
NOTE! To achieve the correct flow, the flow must be measured at the tool.
The flow meter is calibrated for Argon gas at 4 bar pressure. The gas flow obtained
from the tool can vary depending on the connected tool. If other pressures or gases
are used, the gas flow must be measured at the workpiece.
ESAB recommends that a pressure regulator set for 4 bar is used.
dp02d1ea
-- 8 --
GB
6.3
USB connection
The external USB memory can be used to transfer programs to and from systems.
Note!
During normal use there is no risk of ”viruses” ”infecting” equipment. To eliminate the
risk entirely, we recommend that the memory, which is used together with this
equipment, not be used for any other purpose other than its intended.
Certain USB memories may not work with this equipment. We recommend using
USB memories from a reputable supplier.
ESAB assumes no responsibility for any damage caused as a consequence of
incorrect use of the USB memory.
6.4
Water connection
The power source is equipped with a detection system ELP (ESAB Logic Pump)
which checks that the water hoses are connected. When connecting a water--cooled
tube welding tool, the water pump starts.
6.5
Overheating protection
The welding power source has overheating protection that operates if the
temperature becomes too high. When this occurs, the welding current is interrupted
and a red flashing field with the text ”OVERHEAT” appears in the lower right--hand
corner of the control panel.
When the temperature drops, the overheat protection is automatically reset and the
field stops flashing red.
For further information see the control panel user manual.
6.6
Flow guard, water
The water flow guard blocks the power source if the coolant stops (minimum water
flow 0.7 l/min). When this occurs the welding current is interrupted and an error
message is shown on the control panel.
For further information see the control panel user manual.
6.7
Flow guard, gas
The flow guard stops the welding process if the gas flow falls below 4 l/min. When
this occurs an error message appears on the control panel.
For further information see the control panel user manual.
6.8
dp02d1ea
Symbol explanations
TIG--torch
Start and weld gas out
Tube welding tool
Root gas out
-- 9 --
GB
Rotation
Root gas in
Wire feed
Weld gas in
Start gas in
For detailed description of the function see instruction manual for the control panel.
7
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Maintenance must be executed by a professional.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.
7.1
Inspection and cleaning
Power source
Check regularly that the welding power source is not clogged with dirt.
How often and which cleaning methods apply depend on:
S
welding process
S
arc time
S
placement
S surrounding environment.
It is normally sufficient to blow down the power source with dry compressed air
(reduced pressure) once a year.
Clogged or blocked air inlets and outlets can cause overheating.
Tube welding tool
The tube welding tool’s wear parts should be cleaned and replaced at regular
intervals in order to achieve trouble--free welding.
dp02d1ea
-- 10 --
GB
7.2
Topping up the coolant
Top up with coolant to the level of the
filling hole.
ESAB’s refrigerant is recommended for
use. See accessories on page 21.
CAUTION!
The coolant must be handled as chemical waste.
8
FAULT--TRACING
Try these recommended checks and inspections before sending for an authorised
service technician.
Type of fault
No arc.
Corrective action
S
S
S
S
S
The welding current is
interrupted during welding.
S
S
S
Check that the mains power supply switch is turned on.
Check that the welding current supply and return cables are
correctly connected.
Check that the correct current value is set.
Check the coolant flow.
Check the coolant level.
Check whether the overheating protection has operated (fault
code 6 2 is displayed on the control panel).
Check the coolant flow.
Check the mains power supply fuses.
The overheating protection trips
frequently.
S
Make sure that you are not exceeding the rated data for the
welding power source (i.e. that the unit is not being
overloaded).
Poor welding performance.
S
Check that the welding current supply and return cables are
correctly connected.
Check that the correct current value is set.
Check that the correct electrodes are being used.
Check the mains power supply fuses.
Check that the correct welding gas is being used.
S
S
S
S
dp02d1ea
-- 11 --
GB
9
ORDERING SPARE PARTS
MechTig C2002i is designed and tested in accordance with the international and European standards EN 60974--1, 60974--2, 60974--3, 60974--5 and EN 60974--10. It is the obligation of the service unit which has carried out the service or repair work to make sure
that the product still conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
dp02d1ea
-- 12 --
p
-- 13 --
Diagram
dp02e
-- 14 --
Edition 070605
dp02e
-- 15 --
Edition 070605
dp02e
-- 16 --
Edition 070605
dp02e
-- 17 --
Edition 070605
Pump data
P = Pump pressure
Q = Flow rate
dp02k
-- 18 --
Cooling caracteristic
P = Power
tö = Flow rate
dp02k
-- 19 --
MechTig C2002i
Ordering number
Ordering no.
Denomination
Type
0444 600 880 Welding power source
Aristot MechTig C2002i, WO100
0459 839 009 Spare parts list
Aristot MechTig C2002i, WO100
0444 536
Instruction manual
Control panel WO100
Instruction manuals and the spare parts list are available on the Internet at www.esab.com
dp02o
-- 20 --
Edition 070605
MechTig C2002i
Accessories
dp02a
Thermal paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0444 529 002
Coolant (ready mixed)
50 % water and 50% monoethylene glycol (10 l) . . .
0194 230 002
Carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0460 209 880
-- 21 --
Edition 070605
MechTig C2002i
Product
Ordering number
Tube welding tool PRB
17--49 watercooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33--90 watercooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60--170 watercooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17--49 aircooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33--90 aircooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60--170 aircooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0443 750 882
0443 760 882
0443 770 882
0443 750 883
0443 760 883
0443 770 883
Tube welding tool PRD
160 (for meltwelding with floating head) . . . . . . . . . . . . . . . . .
160 with wire feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0444 151 880
0444 151 881
Tube welding tool PRH
3--12 enclosed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3--38 enclosed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6--76 enclosed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0444 300 880
0444 301 880
0444 302 880
Tube welding tool POC 12--60 with wire feed unit . . . . . . . . . . . . .
0443 930 880
TIG hand torch TXH 400W (4 m OKC) . . . . . . . . . . . . . . . . . . . . . .
0460 014 840
Wire feed unit MEI 10
for PRB 17--49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
for PRB 33--90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
for PRB 60--170 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0444 211 880
0444 212 880
0444 213 880
Wire feed unit MEI 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0443 830 880
Remote control unit MechT1 CAN . . . . . . . . . . . . . . . . . . . . . . . . . .
0460 181 880
g Remote cable CAN 4 pole -- 12 pole,
5m .................................................
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0459 554 880
0459 554 881
0459 554 882
0459 554 883
0459 554 884
Documentation system
Welddoct WMS 40000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPS 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opto cable, 15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opto cable, 2 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0457 410 880
0457 410 881
0457 072 881
0457 072 882
Return cable 4,5 m, 25 mm2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0156 743 909
Extension cable
c for wire feed unit and CAN 42 V, 10 m . . . . . . . . . . . . . . . . . . .
d for rotation, 10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0456 904 880
0456 906 880
Extension set
e for current, water and gas, 8 m . . . . . . . . . . . . . . . . . . . . . . . . . .
f for current, water, gas and torch contact, 8 m . . . . . . . . . . . . .
0456 905 880
0466 705 881
dp02a
-- 22 --
Edition 070605
MechTig C2002i
dp02a
-- 23 --
Edition 070605
MechTig C2002i
Product
Automatic welding machine A25
with floating head and TIG torch BTE 250
with floating head and TIG torch BTE 500
with manual slide and TIG torch BTE 250
with manual slide and TIG torch BTE 500
Ordering number
................
................
................
................
0443 912 880
0443 912 881
0443 912 886
0443 912 887
Terminal box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0457 591 880
VEC--motor with gear and pulse generator . . . . . . . . . . . . . . . . . . .
Connection cable
0457 258 880
h for CAN 42 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
i for rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0456 527 881
0457 222 880
Remote control unit MechT1 CAN . . . . . . . . . . . . . . . . . . . . . . . . . .
0460 181 880
g Remote cable CAN 4 pole -- 12 pole
5m .................................................
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0459 554 880
0459 554 881
0459 554 882
0459 554 883
0459 554 884
Documentation system
Welddoct WMS 40000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPS 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opto cable, 15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opto cable, 2 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0457 410 880
0457 410 881
0457 072 881
0457 072 882
Return cable 4,5 m, 25 mm2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0156 743 909
Extension cable
c for wire feed unit and CAN 42 V, 10 m . . . . . . . . . . . . . . . . . . .
d for rotation, 10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0456 904 880
0456 906880
Extension set
e for current, water and gas, 8 m . . . . . . . . . . . . . . . . . . . . . . . . . .
dp02a
-- 24 --
0456 905 880
Edition 070605
MechTig C2002i
dp02a
-- 25 --
Edition 070605
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna--Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
ITALY
ESAB Saldatura S.p.A.
Mesero (Mi)
Tel: +39 02 97 96 81
Fax: +39 02 97 28 91 81
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
Asia/Pacific
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 5308 9922
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 3 5296 7371
Fax: +81 3 5296 8080
MALAYSIA
ESAB (Malaysia) Snd Bhd
Selangor
Tel: +60 3 8027 9869
Fax: +60 3 8027 4754
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
Representative offices
BULGARIA
ESAB Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
EGYPT
ESAB Egypt
Dokki--Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ROMANIA
ESAB Representative Office
Bucharest
Tel/Fax: +40 1 322 36 74
RUSSIA
LLC ESAB
Moscow
Tel: +7 095 543 9281
Fax: +7 095 543 9280
LLC ESAB
St Petersburg
Tel: +7 812 336 7080
Fax: +7 812 336 7060
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
BRAZIL
ESAB S.A.
Contagem--MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
ESAB AB
SE-- 695 81 LAXÅ
SWEDEN
Phone +46 584 81 000
www.esab.com
070514
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising