ESAB | Professional 200 Caddy | Instruction manual | ESAB Professional 200 Caddy User manual

ESAB Professional 200 Caddy User manual
GB
Professional 200
Caddyt
Instruction manual
0468 964 201 GB 060814
Valid for serial no. 632--xxx--xxxx
1
2
3
4
DIRECTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
5
5
4.1 Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Field of application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
5.1 Placing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
7
6 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
6.1 Overload protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7.1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8 FAULT TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 ORDERING OF SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPARE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
10
11
12
13
Rights reserved to alter specifications without notice.
TOCe
-- 2 --
GB
1
DIRECTIVE
DECLARATION OF CONFORMITY
ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that welding power source Professional 200 from serial number 632 complies with standard IEC/EN 60974--1,
in accordance with the requirements of directive (73/23/EEC) and addendum (93/68/EEC) and with
standard IEC/EN 60974--10 in accordance with the requirements of directive (89/336/EEC) and addendum (93/68/EEC).
--------------------------------------------------------------------------------------------------------------------------------------
Laxå 2006--08--11
Kent Eimbrodt
Global Director Equipment and Automation
ESAB AB
695 81 LAXÅ
SWEDEN
2
Tel: + 46 584 81000
Fax: + 46 584 411924
SAFETY
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1.
Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no--one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves.
S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
bh11d1ea
-- 3 --
GB
WARNING
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S
Install and earth the welding unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS -- Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding protection and accessories.
This product is solely intended for arc welding.
WARNING!
Read and understand the instruction manual before installing
or operating.
WARNING!
Do not use the power source for thawing frozen pipes.
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and returned to an
environmentally compatible recycling facility. As the owner of the equipment, you should
get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human health!
bh11d1ea
-- 4 --
GB
3
INTRODUCTION
The Professional 200 are one transistor controlled welding power source designed
for welding with coated electrodes and for TIG welding (touch start).
The advanced electronics provide rapid control response, low power demand and
excellent welding characteristics. Inverter technology contributes to low weight and
compact dimensions of the units.
The rounded slimline shape of the unit makes it comfortable to carry. The strap can
be folded to serve as a carrying handle, or fully extended to serve as a shoulder
strap.
ESAB’s accessories for the product can be found on page 13.
4
TECHNICAL DATA
Professional 200
Performance:
at 35% duty cycle
at 60%
at 100%
Setting range
Open circuit voltage
Mains supply:
voltage
primary current
fuse
mains cable, area
200A/28 V
150A/26 V
115A/25 V
continuously variable 5--200A
50--80 V
400 V
10A
16A
4x1,5 mm2
IP 23
Enclosure class
Application class
Weight
approx. 11 kg
*When welding below 100A a 10A slow fuse is adequate.
Duty cycle
The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a certain load without overloading.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
Welding power source complies with IEC 974--1
Power cable rating complies with Swedish regulations.
bh11d1ea
-- 5 --
GB
4.1
Equipment
Professional 200 is equipped with a remote control socket which activates automatically when a remote control device is connected.
NOTE! The contact pins L and M must be strapped in the remote device’s connection cable for automatic activation to function. The inverter is supplied with a 3 meter
long mains cable.
Professional 200 is delivered with 5 meter long welding and return cables. These are
attached to cable connectors allowing quick change of polarity.
The manufacturer’s serial number is stamped on the rating plate.
4.2
Field of application
Professional 200 supply direct current, which allows you to weld most alloyed and
non--alloyed steels, stainless steels and cast iron. .
With the Professional 200 you can use coated electrodes from ∅1.6 mm to
∅ 4,0 mm.
Tig-- welding
TIG welding is particularly useful when high quality standards are required and when
welding thin sheet.
Before using the Professional 200 for TIG welding it must be equipped with:
S
a TIG torch and gas valve
S
a cylinder of argon
S
an argon regulator
S
tungsten electrodes
S
suitable filler metal, if necessary.
The best method to use is the touch start, where you gently stroke the tungsten
electrode against the workpiece to establish the arc.
5
INSTALLATION
The installation must be executed by a professional.
WARNING!
This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’s responsibility to take adequate precautions.
5.1
Placing
Place the machine so that there is nothing to prevent the cooling air from passing
through it.
bh11d1ea
-- 6 --
GB
5.2
Connection
To get maximum performance from the Professional 200 a 10A fuse is adequate.
(400 V sockets normally have 16A fuses).
The Professional 200 both have mains voltage compensation, which means that
¦10% fluctuation in the supply voltage produces only ¦0.2% variation in the
welding voltage.
Professional 200 is intended for 400V, 3 phase supplies. It can be used with 50 Hz or
60 Hz supplies.
6
OPERATION
General safety regulations for the handling of the equipment can be found on
page 3. Read through before you start using the equipment!
The power switch is at the rear of the Professional 200. The white lamp on the front
will glow when the power is on.
1.
2.
3.
4.
Yellow lamp
Welding current control 3-140A
White lamp
Remote control socket
The current is adjusted using the knob on the front.
Important!
Only use the accompanying welding cable and return cable,
with a cross--sectional area of 25 mm@. (See list of spare parts
for order number).
6.1
bh11d001
Overload protection
To save you worrying about overloading the Professional 250 it has a thermal
cut--out that will trip before the temperature becomes too high. You can tell when the
rectifier has been overloaded because the yellow light comes on and it will no longer
be possible to weld.
7
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.
Maintenance must be executed by a professional.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
bh11d1ea
-- 7 --
GB
7.1
Cleaning
Professional 200 requires a minimum of maintenance. Normally it is sufficient to blow
the unit clean with dry compressed air once a year, and clean the filter in the front
regularly.
If the unit is used in a dirty or dusty environment it should be cleande more often.
The filter is released by inserting, e.g. a screwdriver, in the grille’s slots and prising it
gently upwards.
8
FAULT TRACING
Type of fault
No arc is generated by
the welding power
source.
Measure
S
Make sure the mains switch is on.
S
Check that the welding and return cables are properly connected.
S
Make sure the welding current set is correct.
The welding current is
interrupted in the
course of welding.
S
Check if the thermal cut--out has tripped (the orange indicating lamp
on the front panel is on).
S
Check the mains fuse.
The thermal cut--out
trips frequently.
S
Check that the filter is not packed with dust.
S
Check that the ratings of the welding power source have not been
exceeded (overload of the power source).
Poor welding result.
S
Check that the welding and return cables are properly connected.
S
Make sure the welding current set is correct.
S
Check that there is nothing wrong with the electrodes.
9
ORDERING OF SPARE PARTS
Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.
Professional 200 is designed and tested in accordance with the international and European standards IEC/EN 60974--1 and EN 60974--10. It is the obligation of the service
unit which has carried out the service or repair work to make sure that the product still
conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
bh11d1ea
-- 8 --
p
-- 9 --
Diagram
Professional 200
bh11e11a
-- 10 --
Edition 060814
Professional 200
Ordering number
Ordering no.
Denomination
Type
0468 020 881 Welding power source
Professional 200
0468 964 990 Spare parts list
Professional 200
bh11o11a
-- 11 --
Edition 060814
Professional 200
Spare parts list
Item
Qty
Ordering no.
1
1
0468 462 001
Filter
2
1
0467 796 001
Grill
bh11s11a
Denomination
-- 12 --
Edition 060814
Professional 200
Accessories
Remote control MMA 1 (10 m cable) . . . . . . . 0349 501 024
MMA and TIG: current
Remote control unit AT1 . . . . . . . . . . . . . . . . . 0459 491 896
MMA and TIG: current
Remote control unit AT1 CF . . . . . . . . . . . . . 0459 491 897
MMA and TIG: rough and fine setting of
current.
Remote cable 12 pole -- 8 pole
5m .....................................
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
cmha2s1a
-- 13 --
0459 552 880
0459 552 881
0459 552 882
0459 552 883
p
-- 14 --
p
-- 15 --
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna--Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Prague
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Copenhagen--Valby
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
ITALY
ESAB Saldatura S.p.A.
Mesero (Mi)
Tel: +39 02 97 96 81
Fax: +39 02 97 28 91 81
THE NETHERLANDS
ESAB Nederland B.V.
Utrecht
Tel: +31 30 2485 377
Fax: +31 30 2485 260
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
Asia/Pacific
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 5308 9922
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 3 5296 7371
Fax: +81 3 5296 8080
MALAYSIA
ESAB (Malaysia) Snd Bhd
Selangor
Tel: +60 3 8027 9869
Fax: +60 3 8027 4754
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
Representative offices
BULGARIA
ESAB Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
EGYPT
ESAB Egypt
Dokki--Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ROMANIA
ESAB Representative Office
Bucharest
Tel/Fax: +40 1 322 36 74
RUSSIA
LLC ESAB
Moscow
Tel: +7 095 543 9281
Fax: +7 095 543 9280
LLC ESAB
St Petersburg
Tel: +7 812 336 7080
Fax: +7 812 336 7060
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
BRAZIL
ESAB S.A.
Contagem--MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
ESAB AB
SE-- 695 81 LAXÅ
SWEDEN
Phone +46 584 81 000
www.esab.com
051118
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising