ESAB | CaddyArc 150 VRD | Instruction manual | ESAB CaddyArc 150 VRD User manual

ESAB CaddyArc 150 VRD User manual
Arc 150i VRD
Caddyt A34
Instruction manual
0460 044 074
060326
Valid for serial no. 613--xxx--xxxx,
ENGLISH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rights reserved to alter specifications without notice.
-- 2 --
3
ENGLISH
1 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
6
2.1 Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
3 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
7
4.1 Placing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Rating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Mains power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
7
5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
Connections and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection of welding and return cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VRD functionality (Voltage Reduction Device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MMA welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIG welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
9
10
10
11
12
13
13
6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1 Cleaning the dust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
7 FAULT TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1 Fault codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
8 ORDERING SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPARE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
18
20
21
22
TOCe
-- 3 --
GB
1
SAFETY
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1.
Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no--one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves.
S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and returned to an
environmentally compatible recycling facility. As the owner of the equipment, you should
get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human health!
bh30d1e
-- 4 --
GB
WARNING
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S
Install and earth the welding unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS -- Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding protection and accessories.
WARNING!
Do not use the power source for thawing frozen pipes.
This product is solely intended for arc welding.
bh30d1e
-- 5 --
GB
2
INTRODUCTION
The CaddytArc 150i VRD is a welding current power source intended for use with
coated electrodes (MMA welding) and TIG welding.
2.1
Equipment
The Caddyt Arc 150i VRD is supplied with 3 m of mains cable and an instruction
manual.
ESAB’s accessories for the product can be found on page 22.
3
TECHNICAL DATA
Caddyt Arc 150i VRD
230 V, 1 µ 50/60 Hz
16 A
36 A
21 A
4 A /20 V -- 150 A /26 V
Mains voltage
Fuse (delayed--action)
Primary current Imax
Primary current Ieff
Voltage/current range (DC)
Maximum permissible load at
25% duty cycle
35% duty cycle
60% duty cycle
100% duty cycle
Power factor at maximum current
Efficiency at maximum current
Open--circuit voltage
Operating temperature
Constant A--weighed sound pressure
Dimensions, l x b x h
Weight
Enclosure class
Application class
150 A / 26 V
140 A / 26 V
110 A / 25 V
90 A / 24 V
0,62
77%
30 V
--10˚C -- +40˚ C
< 70 db
394 x 267 x 274 mm
9 kg
IP 23C
Duty cycle
The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a certain load without overloading.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
bh30d1e
-- 6 --
GB
4
INSTALLATION
The installation must be executed by a professional.
WARNING!
Read and understand the instruction manual before installing
or operating.
WARNING!
This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’s responsibility to take adequate precautions.
4.1
Placing
Place the power source so that its cooling air inlets and outlets are not obstructed.
4.2
Rating plate
The rating plate is located on the underside of the power source.
4.3
Mains power supply
Make sure that the welding power source is connected to the correct supply voltage
and that it is protected by the correct fuse rating. The standards for the country in
question must be complied with as regards the mains cable area. A protective earth
connection must be made in accordance with regulations.
4.3.1
Recommended fuse sizes and minimum cable areas
Caddyt Arc 150i VRD
Mains voltage
230 V ¦10 %, 1--phase
50--60 Hz
Mains frequency
Fuse (delayed--action)
100A 20% duty cycle
120A 35% duty cycle
150A 35% duty cycle
10 A
16 A
20 A*)
3 x 2.5 mm2
Mains cable, area
16 mm2
Welding cable, area
*) Note! The installed plug is approved for maximum 15A.
Note! The cable area and fuse rating above comply with Swedish regulations. Use
the welding power source in accordance with the relevant national regulations.
bh30d1e
-- 7 --
GB
5
OPERATION
Connect the power source to the electricity mains with a network impedance of 210 ohm
or lower. If the network impedance is higher, there is a risk of flicker in the illuminators.
5.1
Connections and control devices
1
Main power supply switch, 0 / 1
4
Connection for remote control
2
Mains cable
5
Welding cable connector (+)
3
Connection for return cable (--)
6
Control panel (see 6.2)
3 and 5 are used for welding current supply and return cable connection during MMA
welding
5.2
Connection of welding and return cable
The welding power source has two terminals, one plus and one minus pole, for the
connection of the welding and the return cable. Connect the welding cable to the
pole indicated on the package of the electrode to be used.
Connect the return cable to the other terminal. Fit the earth clamp of the return cable
to the work--piece and make sure there is good contact between the work--piece and
the return cable terminal on the welding power source.
bh30d1e
-- 8 --
GB
5.3
Control panel
Welding process parameters are controlled via the control panel.
5.3.1
Functional description
Pos
Symbol/Function
Set values
1
Knob for setting data
2
Arc Force
0 -- 99%
3
Hot Start
0 -- 99%
4
TIG welding “Live TIG--start”
--
5
MMA welding with coated electrodes -- Light on VRD active
--
6
Pushbutton indicating welding current (A) and/or arc voltage (V)
--
7
Connection of remote control unit
--
8
Indicating lamp (green), mains power supply
--
9
Indicating lamp (yellow) for overheating
--
bh30d1e
--
-- 9 --
GB
5.3.2
Panel function symbols
MMA
Amp/Volt
TIG
5.3.3
Fjärrdon
Hot Start
Arc Force
Hidden functions
A number of setting options for welding data, such as drop welding and ArcPlust,
are obtained by pressing Arc Force
and Hot Start
simultaneously
for at least 1 second. The function is selected using the setting knob, and the
welding method is selected by pressing the ArcForce or HotStart button.
The following welding data setting options for MMA can be found under the letters:
D = setting Drop welding
F = setting regulator ArcPlust
Return by pressing ArcForce
second.
5.4
Off=0 or On =1
Off=1 or On =0
and HotStart
simultaneously for 1
Settings
Settings
Setting range
In steps of:
Default value
Arc Force
0 -- 99%
1%
5%
Drop welding
I/0
--
0
Regulator ArcPlust
I/0
--
1
Hot Start
0 -- 99%
1%
0%
5.5
Overheating protection
The welding power source has a thermal protection which operates if the temperature
becomes too high, interrupting the welding current and lighting a yellow indicating
lamp on the front of the power source. The thermal protection resets automatically
when the temperature has fallen.
bh30d1e
-- 10 --
GB
5.6
VRD functionality (Voltage Reduction Device)
The main task for the VRD function (VRD = voltage reduction device) is to
secure that the open--circuit voltage doesn’t exceed the specified voltage limit
when welding is inactive.
Normally it shouldn’t be possible to occur since hardware functionality for
open--circuit voltage reduction is enabled when not welding. The enable/disable
of the arc voltage reduction function is controlled through software. Arc voltage
reduction is disabled when the system consider welding is active.
If some problem occurs with the voltage reduction function and the arc voltage
exceeds the specified limit, functionality in software detects that and indicates it
to the user. Indication is done by presenting error 16 from unit 2 in the display.
This error can not be cleared out by the user and it will be visible in the display
until the power source is powered off. It is not possible to start a new weld when
the error is active.
To indicate that VRD is active or inactive the MMA lamp on the panel will be
used according to:
S
MMA lamp is on if method MMA is selected, welding is inactive and arc
voltage is under specified limit.
S
MMA lamp is off during MMA welding or error 16 is active.
Knowledge about welding active or inactive is based on the arc on/off message
from the power source.
Normal open--circuit voltage is about 20 V and the limit for error indication is set
to 35 V. Supervision of the open--circuit voltage is activated 750 ms after
enabling of the arc voltage reduction function.
bh30d1e
-- 11 --
GB
5.7
MMA welding
The Caddyt Arc 150i VRD gives direct current, and you can weld most metals to
alloy and non--alloy steel, stainless steel and cast iron.The Caddyt Arc 150i VRD
allows you to weld most coated electrodes from ∅ 1.6 to ∅ 3.25.
MMA welding may also be referred to as welding with coated electrodes. Striking the
arc melts the electrode, and its coating forms protective slag.
If, when striking the arc, the tip of the electrode is pressed against the metal, it immediately melts and sticks to the metal, rendering continued welding impossible.
Therefore, the arc has to be struck in the same way that you would light a match.
Quickly strike the electrode against the metal, then raise it so
as to give an appropriate arc length (approx. 2 mm). If the arc
is too long, it will crackle and spit before finally going out completely.
If you are working on a welding bench, check before attempting to strike the arc that residual waste metal, pieces of electrode or other objects do not insulate the part to be welded.
cmha2p11
Once the arc has been struck, move the electrode from left to
right. The electrode must be at an angle of 60˚ to the metal in
relation to the direction of welding.
When you want to weld wide beads, or when you want the
weld to be so thick that you have to weld in a number of
layers, however, you have to use lateral movements.
cmha2p10
Setting regulator -- ArcPlust
The Caddyt Arc 150i VRD is supplied with ArcPlust, a new type of control that,
during MMA welding, produces a more intensive, more concentrated and calmer arc.
It recovers more quickly after a drop short--circuit, which reduces the risk of the
electrode becoming stuck.
Drop welding (MMA)
Drop welding can be used when welding with stainless electrodes.
This technique involves alternately striking and extinguishing the arc in order to
achieve better control of the supply of heat. The electrode needs only to be raised
slightly to extinguish the arc.
Hot Start
Hot start increases the weld current for an adjustable time at the start of welding,
thus reducing the risk of poor fusion at the beginning of the joint.
Arc Force
The arc force is important in determining how the current changes in response to a
change in the arc length. A lower value gives a calmer arc with less spatter.
bh30d1e
-- 12 --
GB
Current
A higher current produces a wider weld pool, with better penetration into the
workpiece.
The current set value can be changed irrespective of which menu is displayed. This
value is displayed in the main menu only.
5.8
TIG welding
TIG welding melts the metal of the workpiece, using an arc struck from a tungsten
electrode, which does not melt itself. The weld pool and the electrode are protected
by shielding gas.
TIG welding is particularly useful when high quality standards are required and when
welding thin sheet. Caddyt also has very good TIG welding characteristics.
Before using the Caddyt for TIG welding it must be equipped with a TIG torch and
gas valve, a cylinder of argon, an argon regulator, tungsten electrodes and, if
necessary, suitable filter metal.
“Live Tig-- start“
The Live Tig--start“ function strikes the arc when the electrode is brought into contact
with the workpiece and then lifted away from it.
5.9
Remote control unit
The remote control unit has to be connected to the remote control unit socket on the
power source.
If the remote control unit is not to be used, this function is removed from the panel.
bh30d1e
-- 13 --
GB
6
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.
6.1
Cleaning the dust filter
S
Remove the fan grille: see sketch.
S
Release the dust filter
S
Blow the filter clean with compressed air (reduced pressure).
S
Ensure that the filter with the finest mesh is placed towards the grille.
S
Replace the fan grille with the dust filter.
bh30d1e
-- 14 --
GB
7
FAULT TRACING
Try these recommended checks and inspections before sending for an authorised
service technician.
Type of fault
No arc.
Action
S
Check that the mains power supply switch is
turned on.
S
Check that the welding current supply and return
cables are correctly connected.
S
Check that the correct current value is set.
S
Check to see whether the MCB has tripped.
S
Check the main power supply fuses.
The thermal protection
operates frequently.
S
Check to see whether the dust filter is clogged.
S
Make sure that you are not exceeding the rated
data for the power source (i.e. that the unit is not
being overloaded).
Poor welding perform-ance.
S
Check that the welding current supply and return
cables are correctly connected.
S
Check that the correct current value is set.
S
Check that the correct electrodes are being used.
bh30d1e
-- 15 --
GB
7.1
Fault codes
The Caddyt Arc 150i VRD comes with built--in fault monitoring. If a fault occurs, a
code is shown in the display.
If any of these fault codes is displayed permanently or recurs often, the machine
should be sent to an authorised ESAB service workshop for repair.
Fault Description
Action
Resetting
E1
Internal RAM fault
Restart the power source.
If the fault persists, contact a
service workshop
E2
External RAM fault
Restart the power source.
If the fault persists, contact a
service workshop
E3
EPROM fault
Restart the power source.
If the fault persists, contact a
service workshop
E4
Fault in RAM with battery
backup
Restart the power source.
If the fault persists, contact a
service workshop
E5
Memory error, variable value Restart the power source.
outside limits
If the fault persists, contact a
service workshop
E6
Low battery voltage
E10
+ 20V fault
(18.5 – 21.5 V)
Automatic reset once fault
has disappeared
E11
--15 V fault
(--13.0 -- --16.0)
Automatic reset once fault
has disappeared
E13
High temperature
Automatic reset once fault
has disappeared
E14
Current servo fault
Automatic reset once fault
has disappeared Also reset
by pressing a button
E16
VRD fault
Switch off the power source.
Restart the power source
E99
Bridging fault
Switch off the power source.
If the fault persists, contact
the service workshop.
The digital control card is
bridged in a non--defined
combination.
8
If the fault persists, contact a
service workshop
Reset by pressing a button
ORDERING SPARE PARTS
Caddyt Arc 150i VRD is designed and tested in accordance with the international and
European standards IEC/EN 60974--1 and IEC/EN 60974--10. It is the obligation of the
service unit which has carried out the service or repair work to make sure that the product still conforms to the said standard.
Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
bh30d1e
-- 16 --
NOTES
notes
-- 17 --
Diagram
CaddyArc150i VRD
-- 18 --
Caddy Arc 150i VRD
CaddyArc150i VRD
-- 19 --
Caddyt Arc 150i VRD
Ordering number
Ordering no.
Denomination
Type
0459 199 891 Welding Power source
Caddyt Arc 150i VRD for 230 V mains voltage,
Australian version
0459 263 990 Spare parts list
CaddyArc 150 / Caddyt Arc 150i VRD
bh30o
-- 20 --
Edition 060326
Caddyt Arc 150i VRD
Spare parts list
Item
Qty
Ordering no.
101
1
0459 277 001
bh30s
Denomination
Filter
-- 21 --
Edition 060326
Caddyt Arc 150i VRD
Accessories
MMA welding and return cable kit . . . . . . .
(”crocodile” type holder)
0349 501 078
MMA welding and return cable kit . . . . . . . . 0349 501 079
(”screwe” type holder)
Remote control MMA 1 (10 m cable) . . . . . . . 0349 501 024
MMA and TIG: current
Foot control FS002 . . . . . . . . . . . . . . . . . . . . . . 0349 090 886
MMA and TIG current
Remote control unit AT1 . . . . . . . . . . . . . . . . . 0459 491 896
MMA and TIG: current
Remote control unit AT1 CF . . . . . . . . . . . . . 0459 491 897
MMA and TIG: rough and fine setting of
current.
Remote cable 12 pole -- 8 pole
5m .....................................
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0459 552 880
0459 552 881
0459 552 882
0459 552 883
Shoulderstrap . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 367 880
bh30a
-- 22 --
Edition 060326
NOTES
notes
-- 23 --
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna--Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Prague
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Copenhagen--Valby
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
ITALY
ESAB Saldatura S.p.A.
Mesero (Mi)
Tel: +39 02 97 96 81
Fax: +39 02 97 28 91 81
THE NETHERLANDS
ESAB Nederland B.V.
Utrecht
Tel: +31 30 2485 377
Fax: +31 30 2485 260
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
Asia/Pacific
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 5308 9922
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 3 5296 7371
Fax: +81 3 5296 8080
MALAYSIA
ESAB (Malaysia) Snd Bhd
Selangor
Tel: +60 3 8027 9869
Fax: +60 3 8027 4754
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
Representative offices
BULGARIA
ESAB Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
EGYPT
ESAB Egypt
Dokki--Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ROMANIA
ESAB Representative Office
Bucharest
Tel/Fax: +40 1 322 36 74
RUSSIA
LLC ESAB
Moscow
Tel: +7 095 543 9281
Fax: +7 095 543 9280
LLC ESAB
St Petersburg
Tel: +7 812 336 7080
Fax: +7 812 336 7060
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
BRAZIL
ESAB S.A.
Contagem--MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
ESAB AB
SE-- 695 81 LAXÅ
SWEDEN
Phone +46 584 81 000
www.esab.com
051118
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising