ESAB | ESABMig C300i | Instruction manual | ESAB ESABMig C300i User manual

ESAB ESABMig C300i User manual
GB
ESABMig C300i
Instruction manual
0459 825 001 GB 051018
Valid for serial no. 535--xxx--xxxx
1 DIRECTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
5
3.1 Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
4 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
7
5.1 Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Mains power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
6 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
6.1
6.2
6.3
6.4
6.5
6.6
6.7
Connections and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welding without gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire feed pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing and inserting wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing feed rollers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
8
9
9
10
10
7 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.1 Inspection and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
8 FAULT--TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 ORDERING SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEAR COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
12
14
16
18
20
Rights reserved to alter specifications without notice.
TOCe
-- 2 --
GB
1
DIRECTIVE
DECLARATION OF CONFORMITY
ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that welding power source ESABMig C300i from serial number 535 complies with standard IEC/EN 60974--1
/--5, in accordance with the requirements of directive (73/23/EEC) and addendum (93/68/EEC) and
with standard IEC/EN 60974--10 in accordance with the requirements of directive (89/336/EEC) and
addendum (93/68/EEC).
--------------------------------------------------------------------------------------------------------------------------------------
Laxå 2005--10--17
Denis Sharp
Technical Director
ESAB AB, Welding Equipment
SE--695 81 LAXÅ
SWEDEN
2
Tel: + 46 584 81000
Fax: + 46 584 411924
SAFETY
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1.
Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no--one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves.
S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
bc19d1ea
-- 3 --
GB
WARNING!
Read and understand the instruction manual before installing
or operating.
WARNING
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S
Install and earth the welding unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS -- Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding protection and accessories.
WARNING!
Do not use the power source for thawing frozen pipes.
This product is solely intended for arc welding.
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and returned to an
environmentally compatible recycling facility. As the owner of the equipment, you should
get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human health!
bc19d1ea
-- 4 --
GB
3
INTRODUCTION
ESABMig C300i is a welding power source intended for MIG/MAG welding with solid
wire made of steel, stainless steel, aluminium as well as cored wire with or without
shielding gas. It is also possible to weld with coated electrodes (MMA welding).
The power sources comes in different variants, see page 16
ESAB’s accessories for the product can be found on page 20.
3.1
Equipment
The welding power source is supplied with:
S
S
S
S
Instruction manual for the welding power source
Instruction manual in english for the control panel
Decal with recommended wear parts
5 metre return cable
3.2
Control panel
The welding power source is supplied with one of the following control panels:
MA23
With knobs for setting the voltage and wire feed speed /
current. Other settings by pushbuttons.
MA23A
With knobs for setting the voltage / QSett and wire feed
speed / current. Other settings by pushbuttons.
Detailed descriptions of the control panels can be found in separate Instruction
manual.
4
TECHNICAL DATA
ESABMig C300i
Mains voltage
400 V, ±10%, 3∼ 50/60 Hz
Primary current
Imax MIG/MAG
Imax MMA
21 A
23 A
No--load power demand when in the
energy--saving mode, 6.5 min. after welding
30 W
Setting range
MIG/MAG
MMA
8--48 V / 16--300 A
16 -- 300 A
Permissible load at MIG/MAG
35% duty cycle
60% duty cycle
100% duty cycle
300 A / 29 V
240 A / 26 V
200 A / 24 V
bc19d1ea
-- 5 --
GB
ESABMig C300i
Permissible load at MMA
30% duty cycle
60% duty cycle
100% duty cycle
300 A / 32 V
230 A / 29.2 V
190 A / 27.6 V
Power factor at maximum current
MIG/MAG
MMA
0.70
0.73
Efficiency at maximum current
MIG/MAG
MMA
84 %
83 %
Open--circuit voltage
MIG/MAG
MMA
70 -- 80 V
57 -- 67 V
Operating temperature
--10 to +40˚C
Constant A--weighed sound pressure
< 70 dB
Dimensions lxwxh
652 x 412 x 423 mm
Weight
38 kg
Insulation class transformer
H
Enclosure class
IP 23C
Application class
Gun connection
EURO
Max. diameter wire bobbin
300 mm
Wire dimension
Fe
Ss
Al
Cored wire
0.6
0.6
1.0
0.8
Shielding gas
max pressure
All types intended for MIG/MAG welding
5 bar
Motor current Imax
3.5 A
-----
1.2 mm
1.2 mm
1.2 mm
1.2 mm
Duty cycle
The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a certain load without overloading.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
bc19d1ea
-- 6 --
GB
5
INSTALLATION
The installation must be executed by a professional.
WARNING!
This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’s responsibility to take adequate precautions.
5.1
Location
Position the welding power source such that its cooling air inlets and outlets are not
obstructed.
5.2
Mains power supply
Check that the welding power source is connected to the
correct mains power supply voltage, and that it is protected by
the correct fuse size. A protective earth connection must be
made in accordance with regulations.
Rating plate with supply connection data
Recommended fuse sizes and minimum cable area
ESABMig C300i
Mains voltage
Mains cable area mm2
Phase current, I RMS
Fuse
Anti--surge
Type C MCB
MIG/MAG
MMA
400 V 3µ 50 Hz
4G2.5
13 A
400 V 3µ 50 Hz
4G2.5
14 A
16 A
20 A
16 A
20 A
Note! The mains cable areas and fuse sizes as shown above are in accordance with Swedish
regulations. Use the welding power source in accordance with the relevant national regulations.
Note! This welding power source is designed for connection to a four wire 230/400
volt system.
If the power source is to be used in a country with a higher mains voltage, the power
source shall be connected via a safety transformer.
6
OPERATION
General safety regulations for the handling of the equipment can be found on
page 3. Read through before you start using the equipment!
When moving the equipment use intended handle. NOTE! Never pull on the gun.
WARNING!
Assure that the side panels are closed during operation.
bc19d1ea
-- 7 --
GB
WARNING!
To prevent the reel from sliding off the hub: Lock the reel in place by
turning the red knob as shown on the warning label attached next to
the hub.
WARNING!
Rotating parts can cause injury, take great care.
6.1
Connections and control devices
1
Control panel,
see separate instruction manual
5
Connection for welding gun
2
CAN connection for cooling unit or remote
control unit
6
Mains voltage switch
3
Connection for return cable (--)
7
Connection for shielding gas
4
Connection for welding current cable (+)
(MMA welding)
6.2
Fan control
The power source has a time control that means that the fans continue to run for 6.5
minutes after welding has stopped, and the unit switches to energy--saving mode.
The fans start again when welding restarts.
The fans run at reduced speed for welding currents up to 110 A, and at full speed for
higher currents.
6.3
Overheating protection
The welding power source has overheating protection which operate if the
temperature becomes too high, When this occurs the welding current is interrupted
and a fault code is displayed on the control panel.
The overheating protection resets automatically when the temperature has fallen.
bc19d1ea
-- 8 --
GB
6.4
Welding without gas
It is possible to switch between welding with a solid wire and shielding gas, or
welding with self shielded cored wire without gas.
Solid wire
Self shielded core wire without gas
S
S
S
Disconnect the welding power source from the mains current supply.
S
S
Reinstall the protective cover. Close the side panel.
Open the side panel. Remove the protective cover.
Rechuck the positive connection (+) and negative connection (--) on the terminal block above the
feed mechanism.
Move the return cable from the negative outlet (--) to the positive
outlet (+).
6.5
Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then
set the pressure of the wire feeder’s pressure rollers. It is important that the
pressure is not too great.
Fig 1
Fig 2
To check that the feed pressure is set correctly, you can feed out the wire against
an insulated object, e.g. a piece of wood.
When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed
rollers should slip.
If you hold the gun approx. 50 mm from the piece of wood, the wire should be
fed out and bend (fig. 2).
bc19d1ea
-- 9 --
GB
6.6
S
S
S
S
S
S
Replacing and inserting wire
Open the side panel.
Disconnect the pressure sensor by folding it backwards, the pressure rollers
slide up.
Straighten out the new wire 10--20 cm. File away burrs and sharp edges from the
end of the wire before inserting it into the wire feed unit.
Make sure that the wire goes properly into the feed roller’s track and into the
outlet nozzle and the wire guide.
Secure the pressure sensor.
Close the side panel.
6.7
Changing feed rollers
Open the side panel.
Disconnect the pressure sensor (1) by folding it
backwards, the pressure rollers slide up.
S Disconnect the pressure rollers (2) by turning the
axle (3) 1/4 turn clockwise and pulling out the axle.
The pressure rollers disconnect.
S Disconnect the feed rollers (4) by unscrewing the nuts
(5) and pulling out the rollers.
During installation, repeat the above in the reverse order.
S
S
Choice of tracks in the feed rollers
Turn the feed roller with the dimensioning mark for the required
track towards you.
7
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.
Maintenance must be executed by a professional.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
7.1
Inspection and cleaning
Power source
Check regularly that the welding power source is not clogged with dirt.
How often and which cleaning methods apply depend on: the welding process, arc
times, placement, and the surrounding environment. It is normally sufficient to blow
the dust out of the power source with dry compressed air (reduced pressure) once a
year.
bc19d1ea
-- 10 --
GB
Clogged or blocked air inlets and outlets otherwise result in overheating.
Wire feed unit
Check regularly that the wire feed unit is not clogged with dirt.
S
Cleaning and replacement of the wire feed unit mechanism’s worn parts should
take place at regular intervals in order to achieve trouble--free wire feed. Note
that if pre--tensioning is set too hard, this can result in abnormal wear on the
pressure roller, feed roller and wire guide.
The brake hub
The hub is adjusted when delivered, if
readjustment is required, follow the instructions
below. Adjust the brake hub so that wire is slightly
slack when wire feed stops.
S
Adjusting the braking torque:
S
Turn the red handle to the locked position.
S
Insert a screwdriver into the springs in the hub.
Turn the springs clockwise to reduce the braking torque
Turn the springs counterclockwise to increase the braking torque. NB: Turn
both springs through the same amount.
Welding gun
S
Cleaning and replacement of the welding gun’s wear parts should take place at
regular intervals in order to achieve trouble--free wire feed. Blow the wire guide
clean regularly and clean the contact tip.
8
FAULT--TRACING
Try these recommended checks and inspections before sending for an authorised
service technician.
Type of fault
No arc.
Action
S
S
S
The welding current is
interrupted during welding.
S
S
Check that the mains power supply switch is turned on.
Check that the welding current supply and return cables are
correctly connected.
Check that the correct current value is set.
Check whether the overheating protection has operated (fault
code E6 is displayed on the control panel).
Check the mains power supply fuses.
The overheating protection trips
frequently.
S
Make sure that you are not exceeding the rated data for the
welding power source (i.e. that the unit is not being
overloaded).
Poor welding performance.
S
Check that the welding current supply and return cables are
correctly connected.
Check that the correct current value is set.
Check that the correct wire is being used.
Check the mains power supply fuses.
S
S
S
bc19d1ea
-- 11 --
GB
9
ORDERING SPARE PARTS
ESABMig C300i is designed and tested in accordance with the international and European standards IEC/EN 60974--1, 60974--5 and 60974--10. It is the obligation of the service unit which has carried out the service or repair work to make sure that the product
still conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
bc19d1ea
-- 12 --
p
-- 13 --
Diagram
bc19e
-- 14 --
Edition 051018
bc19e
-- 15 --
Edition 051018
ESABMig C300i
Ordering number
Ordering no.
Denomination
Type
0459 750 880 Welding power source
ESABMig C300i with control panel MA23
0459 750 881 Welding power source
ESABMig C300i with control panel MA23A
0459 825 990 Spare parts list
ESABMig C300i with control panel MA23 and MA23A
0459 912 xxx Instruction manual
Control panel MA23 and MA23A
The instruction manuals and the spare parts list are available on the Internet at www.esab.com
Under ”Products” and ”Welding & cutting equipment”, you will find a link to the page where you can
both search for and download instructions and spare parts lists.
bc19o
-- 16 --
Edition 051018
p
-- 17 --
ESABMig C300i
Wear components
S= Standard, HD = Heavy Duty
Item
Ordering no.
Denomination
Wire type
HI 1
0455 072 002
0456 615 001
Intermediate nozzle (S)
Intermediate nozzle
Fe, Ss & cored
Al
HI 2
0469 837 880
0469 837 881
Outlet nozzle (S)
Outlet nozzle
Fe, Ss & cored
Al
HI 3
0191 496 114
Key
HI 4
0215 701 007
Locking washer
HI 5a
0459 440 001
Motor gear euro
Item
Ordering no.
Denomination
HI 5b
0459 052 001
0459 052 002
0459 052 003
Feed/pressure rollers
Feed/pressure rollers
Feed/pressure rollers (S)
Fe, Ss & cored
Fe, Ss & cored
Fe, Ss & cored
0458 825 001
Feed/pressure rollers
0458 824 001
0458 824 002
0458 824 003
Feed/pressure rollers
Feed/pressure rollers
Feed/pressure rollers
Wire type
Wire dimensions
Ø 2.0 mm steel for 0.6--1.2 mm
Ø 2.0 mm plastic for 0.8--1.2 mm
Wire dimensions
Groove
typ
Roller
markings
Ø 0.6 & 0.8 mm
Ø 0.8 & 0.9/1.0 mm
Ø 0.9/1.0 & 1.2 mm
V
V
V
0.6 S2 & 0.8 S2
0.8 S2 & 0.9/1.0 S2
0.9/1.0 S2 & 1.2 S2
Cored
Ø 0.9/1.0 & 1.2 mm
V--Knurled
1.0 R2 & 1.2 R2
Al
Al
Al
Ø 0.8 & 0.9/1.0 mm
Ø 1.0 & 1.2 mm
Ø 1.2 mm
U
U
U
0.8 A2 & 1.0 A2
1.0 A2 & 1.2 A2
1.2 A2
Use only pressure and feed rollers marked A2, R2 or S2.
The rollers are marked with wire dimension in mm, some are also marked with inch.
Item
Ordering no.
Denomination
Notes
HI 6
Washer
Ø 16/5x1
HI 7
Screw
M4x12
HI 8
Screw
M6x12
Washer
Ø 16/8.4x1.5
HI 9
HI 10
0469 838 001
Cover
HI 11
0458 722 880
Axle and Nut
HI 12
0459 441 880
Gear adapter
HI 13
0455 049 001
Inlet nozzle
HI 14
0458 999 001
Shaft
Welding with aluminium wire
In order to weld with aluminium wire, proper rollers, nozzles and liners for aluminium wire MUST be
used, It is recommended to use 3 m long welding gun for aluminium wire, equipped with appropriate
wear parts.
ba40w
-- 18 --
Edition 051018
ESABMig C300i
ba40w
-- 19 --
Edition 051018
ESABMig C300i
Accessories
Cooling unit ESAB Cooler
0459 800 880
Remote control adapter RA12 12 pole . . . . . 0459 491 910
For analogue remote controls to CAN based
equipment.
Remote control unit MTA1 CAN . . . . . . . . . . . 0459 491 880
MIG/MAG: wire feed speed and voltage MMA:
current and arc force
TIG: current, pulse and background current
Remote control unit M1 10Prog CAN . . . . . . . 0459 491 882
Choice of on of 10 programs
MIG/MAG: voltage deviation
TIG and MMA: current deviation
Remote control unit AT1 CAN . . . . . . . . . . . . . 0459 491 883
MMA and TIG: current
Remote control unit AT1 CF CAN . . . . . . . . . . 0459 491 884
MMA and TIG: rough and fine setting of
current.
Remote control cable 12 pole -- 4 pole
5m ......................................
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
bc19a
-- 20 --
0459 554 880
0459 554 881
0459 554 882
0459 554 883
0459 554 884
Edition 051018
ESABMig C300i
Return cable 5 m 50mm2
0156 743 907
Welding torch
Type
yp
Ordering no.
Max welding current
Hose length
Shielding gas
Wi
Wire
dimensions
3m
4.5 m
CO2
Mix Ar
PSF 250
0368 100 882
0368 100 883
250A 60%
225A 60%
0.6 -- 1.0
PSF 250 C
0468 410 882
0468 410 883
250A 60%
225A 60%
0.6 -- 1.0
PSF 305
0458 401 880
0458 401 881
315A 60%
285A 60%
0.8 -- 1.2
PSF 315 CLD
0468 410 885
0468 410 886
315A 60%
285A 60%
0.8 -- 1.2
PSF 405
0458 401 882
0458 401 883
380A 60%
325A 60%
0.8 -- 1.6
PSF 405 C
0458 499 882
0458 499 883
380A 60%
325A 60%
1.0 -- 1.6
PSF 405 RS3
0458 401 892
0458 401 893
380A 60%
325A 60%
0.8 -- 1.6
--
0458 499 889
380A 60%
325A 60%
1.0 -- 1.6
PSF 410 CW
0458 450 880
0458 450 881
380A 100%
325A 100%
0.8 -- 1.6
PSF 410 W
0458 400 882
0458 400 883
400A 100%
350A 100%
0.8 -- 1.6
PSF 410 CW RS3
0458 450 884
0458 450 885
380A 100%
325A 100%
0.8 -- 1.6
PSF 410 W RS3
0458 400 898
0458 400 899
400A 100%
350A 100%
0.8 -- 1.6
PSF 405 C RS3
C
LD
W
RS3
bc19a
=
=
=
=
=
Self cooled
Smoke exhausters, Centrovac
Smaller, Light duty
Water cooled
3--step program switch for selecting preset programs.
-- 21 --
Edition 051018
p
-- 22 --
p
-- 23 --
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna--Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Prague
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Copenhagen--Valby
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
ITALY
ESAB Saldatura S.p.A.
Mesero (Mi)
Tel: +39 02 97 96 81
Fax: +39 02 97 28 91 81
THE NETHERLANDS
ESAB Nederland B.V.
Utrecht
Tel: +31 30 2485 377
Fax: +31 30 2485 260
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB International AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
Asia/Pacific
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 5308 9922
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 3 5296 7371
Fax: +81 3 5296 8080
MALAYSIA
ESAB (Malaysia) Snd Bhd
Shah Alam Selangor
Tel: +60 3 5511 3615
Fax: +60 3 5512 3552
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
Representative offices
BULGARIA
ESAB Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
EGYPT
ESAB Egypt
Dokki--Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ROMANIA
ESAB Representative Office
Bucharest
Tel/Fax: +40 1 322 36 74
RUSSIA-- CIS
ESAB Representative Office
Moscow
Tel: +7 095 937 98 20
Fax: +7 095 937 95 80
ESAB Representative Office
St Petersburg
Tel: +7 812 325 43 62
Fax: +7 812 325 66 85
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
BRAZIL
ESAB S.A.
Contagem--MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
ESAB AB
SE-- 695 81 LAXÅ
SWEDEN
Phone +46 584 81 000
www.esab.com
041227
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising