ESAB | A2 SFE1 / A2 SGE1 | Instruction manual | ESAB A2 SFE1 / A2 SGE1 User manual

ESAB A2 SFE1 / A2 SGE1 User manual
A2 S Mini Master
A2 S G Master
A2 SFE1 / A2 SGE1
101103105107109111102021110025108024042106023061104022041100020040060001
Bruksanvisning
Brugsanvisning
Bruksanvisning
Käyttöohjeet
Instruction manual
Betriebsanweisung
Manuel d’instructions
Gebruiksaanwijzing
Instrucciones de uso
Istruzioni per l’uso
Manual de instruções
Ïäçãßåò ÷ñÞóåùò
0456 552 001
Valid from Serial NO 740 XXX--XXXX
981111
SVENSKA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
DANSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
NORSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SUOMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
ENGLISH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
DEUTSCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
NEDERLANDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
ITALIANO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
PORTUGUÊS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
ÅËËÇÍÉÊÁ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Rätt till ändring av specifikationer utan avisering förbehålles.
Ret til ændring af specifikationer uden varsel forbeholdes.
Rett til å endre spesifikasjoner uten varsel forbeholdes.
Oikeudet muutoksiin pidätetään.
Rights reserved to alter specifications without notice.
Änderungen vorbehalten.
Sous réserve de modifications sans avis préalable.
Recht op wijzigingen zonder voorafgaande mededeling voorbehouden.
Reservado el derecho de cambiar las especificaciones sin previo aviso.
Ci riserviamo il diritto di variare le specifiche senza preavviso.
Reservamo--nos o direito de alterar as especificações sem aviso prévio.
Äéáôçñåßôáé ôï äéêáßùìá ôñïðïðïßçóçò ðñïäéáãñáöþí ×ùñßò ðñïåéäïðïßçóç.
-- 2 --
ENGLISH
1 DIRECTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
3.2
3.3
3.4
3.5
60
60
61
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welding method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
61
62
62
63
4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
64
64
5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
5.1
5.2
5.3
5.4
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conversion of A2 SFE1 (Submerged arc welding) to MIG/MAG welding . . . . . . . . . . .
Conversion of A2 SFE1 (Submerged arc welding) to Twin--arc . . . . . . . . . . . . . . . . . . .
66
66
70
70
6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
6.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Daily . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 Regularly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
70
71
7 FAULT TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
8 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
9 ORDERING OF SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
WEAR COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
SPARE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
TOCe
-- 59 --
GB
1
DIRECTIVE
DECLARATION OF CONFORMITY
Esab Welding Equipment AB, 695 81 Laxå, Sweden, gives its unreserved guarantee
that automatic welding machine A2 SFE1 / A2 SGE1 from serial number 740 complies with standard EN 60292, in accordance with the requirements of directive
(89/392/EEA) and addendum.
-------------------------------------------------------------------------------------------------------------------------------------Laxå 97--09--29
Paul Karlsson
Managing Director
Esab Welding Equipment AB
695 81 LAXÅ
SWEDEN
2
Tel: + 46 584 81000
Fax: + 46 584 12336
SAFETY
Users of ESAB automatic welding machines have ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions.
The following recommendations should be observed in addition to the standard regulations that apply
to the work place.
All work must be carried out according to the specified instructions by personnel who are thoroughly
familiar with the operation of the welding machine.
Incorrect or unintentional operation of the equipment may lead to a hazardous situation which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the automatic welding machine must be familiar with:
S its operation
S the location of emergency stops
S its function
S relevant safety precautions
2. The operator must ensure that:
S no unauthorized person is stationed within the working area of the machine when it is started
up.
S that no--one is in a hazardous position when the carriage or slide mechanisms are operated.
3. The work place must:
S be clear of mechanical components, tools, or other obstructions that could prevent the operator from moving freely within the working area.
S be organized so that there is free access to the emergency stop.
4. Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves.
S Do not wear loose--fitting items, such as scarves, bracelets, etc., which could become
trapped.
5. General precautions
Live electrical components are normally shielded from accidental contact.
S Make sure the return cable is connected securely.
S Work on high voltage components may only be carried out by a qualified electrician.
S Appropriate fire extinguishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during its operation.
dha5d1ea
-- 60 --
GB
WARNING
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S
Install and earth the welding unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to keep fumes and gases from your breathing zone and
the general area.
ARC RAYS -- Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S
Protect your ears. Use ear defenders or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
3
INTRODUCTION
3.1
General
All the automatic welding machines included in this instruction manual are designed
for SAW and MIG/MAG welding of butt and fillet joints.
ESAB’s welding heads are of the A2 S type and are intended for use in combination
with A2--A6 Process Controller and ESAB’s welding power sources LAF and TAF.
The welding head can be positioned horizontally and vertically with the linear slides.
The angular position is adjusted with the angular slide.
3.2
Definitions
SAW welding
The weld bead is protected by a cover of flux during the
welding.
SAW Light duty
Permits welding with lower current load and thinner wire.
MIG/MAG welding
The weld bead is protected by shielding gas during welding.
Tandem welding
Welding with two welding heads.
Twinarc welding
Welding with two wires in the same welding head.
dha5d1ea
-- 61 --
GB
3.3
Technical data
A2 SFE1
A2 SGE1
Submerged--arc
MIG/MAG
LD D20
Rated load 100%
800 AAC/DC
600 A AC/DC
1.6--4.0 mm
1.6--4.0 mm
2x1.2--2.0 mm
0.8--2.5 mm
1.2--3.2 mm
--
0.2--9.0 m/min
0.2--16 m/min
Brake drum braking torque
1.5 Nm
1.5 Nm
Max weight, wire
2x30 kg
2x30 kg
6l
--
50 kg
15 kg
25_
25_
90 mm
90 mm
Wire dimensions:
solid single wire
flux--cored wire
twin wire
Wire feed speed
Flux hopper capacity
(Must not be filled with preheated flux)
Weight (flux and wire excluded)
Sideways tilt, max.
Setting length of slide *
manual drive
*) NB! Other lengths on request.
3.4
Welding method
Submerged arc welding (SAW)
For submerged arc welding, the A2 SF welding head is always to be used.
S
Submerged arc Light duty
Submerged arc light duty, with a ∅ 20 mm connector, which permits a load of up
to 800 A (100%).
This version can be equipped with feed rollers for single or twin wire welding
(twin--arc). A special knurled feed roller is available for flux--cored wire, which
guarantees even wire feed without the risk of deformation due to high feed pressure.
MIG/MAG welding
For MIG/MAG welding the A2 SG welding head is always used, permitting a max.
load of 600 A. The welding head is water--cooled, with the cooling water supplied by
hoses from connections intended for the purpose.
dha5d1ea
-- 62 --
GB
3.5
Equipment
The complete welding head includes a feed motor for the wire feed and contact
equipment supplying current to the wire and ensuring good contact.
The contact equipment is available in different versions.
S
A2 SF is used for Submerged arc welding.
S
A2 SG is used for MIG/MAG welding.
Example - A2 SFE1
1. Wire straightener
2. Contact equipment consisting of
contact tip, connector and flux tube
3. Angular slide
4. Slide
5. Feed motor
6. Wire drum
7. Flux hopper (may be fitted with a cyclone)
Example - A2 SGE1
1. Wire straightener
2. Contact equipment consisting of
connector, gas nozzle and water
hoses.
3. Angular slide
4. Slide
5. Feed motor
6. Wire drum.
7. Fine--wire straightener
8. Wire guide
Connection instructions for SAW and MIG/MAG welding appear from the system
diagram on page 64.
dha5d1ea
-- 63 --
GB
4
INSTALLATION
4.1
General
Installation shall only be performed by qualified personnel.
WARNING!
Rotating parts can cause injury, take great care.
4.2
Mounting
The automatic welding machines can easily be fitted on a rail--borne carriage or on a
column and boom unit with 4 screws.
4.3
Connections
1. The connection of the A2--A6 Process Controller (PEH) to the welding machine
shall be done according to the connection instructions in the A2--A6 Process
Controller (PEH) service manual.
For further information, see instruction manual for the A2--A6 Process Controller
(PEH).
2. Connect the A2 welding heads as follows:
SUBMERGED ARC WELDING (SAW)
S Connect the control cable (7) between the welding power source (8) and the
A2--A6 Process Controller (PEH) (2).
S Connect the return cable (11) between the welding power source (8) and the
work piece (9).
S Connect the welding cable (10) between the welding power source (8) and
the automatic welding machine (1).
S Connect the measuring cable (12) between the welding power source (8)
and the work piece (9).
dha5d1ea
-- 64 --
GB
GAS METAL ARC WELDING (MIG/MAG)
S Connect the control cable (7) between the welding power source (8) and the
A2--A6 Process Controller (PEH) (2).
S Connect the return cable (11) between the welding power source (8) and the
work piece (9).
S Connect the welding cable (10) between the welding power source (8) and
the automatic welding machine (1).
S Connect the gas hose (5) between the reduction valve (6) and the gas valve
on the automatic welding machine (13).
S Connect the hoses for cooling water (3) between the cooling unit (4) and the
automatic welding machine (1).
S Connect the measuring cable (12) between the welding power source (8)
and the work piece (9).
dha5d1ea
-- 65 --
GB
5
OPERATION
5.1
General
General safety regulations for the handling of the equipment appear from
page 60. Read through before you start using the equipment!
S
Select wire type and flux powder or shielding gas so that the weld material is as
close as possible to the analysis of the base metal. Select wire size and welding
data in accordance with the values recommended by the welding materials
supplier.
S
Thorough preparation of the weld surfaces is necessary to achieve a good weld.
NOTE! The width of the weld joint gap must be uniform.
S
To minimise the risk of heat crack formation, the width of the weld must be
greater than the penetration depth.
S
Always carry out a test weld with the same joint type and sheet thickness as the
production work piece.
S
For control and adjustment of the automatic welding machine and welding power
supply, see the instruction manual for the A2--A6 Process Controller (PEH).
S
When changing consumables, see table on page 178.
5.2
Starting work
Loading the welding wire
S
Remove the wire drum (1) from the brake hub (2)
and take off the side plate (3).
S
Locate the wire reel on the wire drum (1).
S
Cut off the binding wires from around the
wire reel.
S
Replace the side plate (3).
Replace the wire drum (1) on the brake hub (2).
Check that the carrier (4) is in the correct position.
NOTE! The maximum angle for the wire bobbin is 25°.
At extreme angles, wear will occur on the brake hub locking
mechanism and the wire bobbin will slide off the brake hub.
S
IMPORTANT!
To prevent the reel sliding off the hub: Lock the reel in place
by turning the red knob as shown on the warning label attached next to the hub.
dha5d1ea
-- 66 --
GB
SAW
MIG/MAG
S
Check that the feed roller (1) and contact jaw or contact tip (3) are of the correct
dimension for the selected wire size.
S
Pull the end of the wire through the straightener (2). For a wire diameter greater
than 2 mm; straighten out 0.5 m of wire and feed it by hand down through the
straightener.
S
Locate the end of the wire in the feed roller (1) groove.
S
Set the wire tension on the feed roller with the knob (7). Note! Do not tension
more than is required to achieve an even feed.
S
Feed the wire forward 30 mm by pressing
Process Controller.
S
Direct the wire by adjusting the knob (6).
on the control box A2--A6
For fine wire, the special fine--wire straightener (4) is used for both single and
twin wire.
Ensure that the straightener is correctly adjusted so that the wire emerges
straight out through the contact jaws or contact tip.
Always use a guide tube (5) to ensure even feed of fine wire (1.6 -- 2.5 mm).
For MIG/MAG welding with wire sizes < 1.6 mm, use a guide spiral, which is
inserted in the guide tube (5).
dha5d1ea
-- 67 --
GB
Changing the feed roller
S
S
S
Single wire
S Release the knobs (3) and (4).
S Release the hand wheel (2).
S Change the feed roller (1). They are marked with their
respective wire sizes.
Twin wire (Twin-- arc)
S Change the feed roller (1) with twin grooves in the same way as for single
wire.
S NOTE! The pressure roller (5) must also be changed. A special curved
pressure roller for twin wire replaces the standard pressure roller for single
wire.
S Assemble the pressure roller with special stub shaft
(order no. 0146 253 001).
Flux-- cored wire (for knurled rollers)
S Change the feed roller (1) and pressure roller (5) as a pair for the wire size
to be used. NOTE! A special stub shaft is required for the pressure roller
(order no. 0212 901 101).
S Tighten the pressure screw (4) with moderate pressure to ensure that the
flux--cored wire does not deform.
Contact equipment for Submerged arc welding
S
For single wire 3.0 - 4.0 mm. Light duty (D20)
Use the straightener (3), connector (1) D20 with
contact tip (2) (M12 thread).
S Tighten the contact tip (2) with a key in order to ensure
that a good contact is achieved.
S
For single wire 1.6 - 2.5 mm Submerged-- arc
Light duty (D20)
Use the straightener (3), connector (1) D20 with contact
tip (2) (M12 thread) and separate fine--wire straightener (4)
with guide tube (6).
S Assemble the clamp (7) with guide tube (6) in the M12
hole on the straightener (3). The guide tube (6) should
bottom on the contact tip (2).
S If necessary, cut the guide tube (6) to length so that the
feed roller (5) runs freely.
S Assemble the fine--wire straightener (4) on the upper
side of the clamp for the straightener (3).
dha5d1ea
-- 68 --
GB
S
For twin wires 2 x 1.2 - 2.0 mm, Light Twin (D35) (Accessories)
Use the straightener (3), connector (1) D35 with
twin adapter (9) and 2 contact tips (2) (M6 threads)
and separate fine--wire straightener (4) with two guide
tubes (6). For twin wires <1.6 mm, a guide spiral,
inserted into each guide tube, is used.
S
Assemble the twin adapter (9) for M6 contact tips (2)
with the M5 bolts in the fixed half of the two--piece
connector (1).
S
Assemble the clamp (7) with guide tube (6) in the M12 hole
on the standard straightener (3). The guide tube should
bottom on the twin adapter (9) for the contact tip (2).
Tighten the contact tip (2) with a key to ensure that good
contact is achieved.
If necessary, cut the guide tube (6) to length so that the
feed roller (5) runs freely.
S
S
S
Adjustment of the wires for Twin-- arc welding:
S Position the wires in the joint so as to achieve optimal weld quality by
rotating the connector. The two wires can be rotated so that they are
positioned one after the other along the line of the joint, or in any position
up to 90° across the joint, i.e. one wire on each side of the joint.
Contact equipment for MIG/MAG welding
S
For single wire 1.6 - 2.5 mm (D35)
Use the straightener (3), connector (1) D35 with contact
tip (2) (M10 thread).
S Tighten the contact tip (2) with a key to ensure that good
contact is achieved.
S Assemble the clamp (7) with guide tube (6) in the M12
hole on the standard straightener (3). The guide tube (6)
should bottom on the contact tip (2).
S
S
If necessary, cut the guide tube (6) to length so that the
feed roller (5) runs freely.
For single wire < 1.6 mm (D35)
Use the straightener (3), connector (1) D35 with contact tip (2)
(M12 thread), fine--wire straightener (4) with guide tube (6)
and guide spiral, which is inserted in the guide tube (6).
S Assemble the clamp (7) with guide tube (6) in the M12
hole on the standard straightener (3). The guide tube (6)
should bottom on the contact tip (2).
S If necessary, cut the guide tube (6) to length so that the
feed roller (5) runs freely.
Assemble the fine--wire straightener (4) on the upper
side of the clamp for the straightener (3).
Connect the cooling water and gas (MIG/MAG welding).
S
S
dha5d1ea
-- 69 --
GB
Refilling with flux powder (Submerged arc welding)
S
Close the flux valve on the flux hopper.
S
Remove the cyclone on the flux recovery unit, if fitted.
S
Fill with flux powder. NOTE! The flux powder must be dry. Where possible avoid
using agglomerating flux powder outdoors and in damp environments.
S
Position the flux tube so that it does not become kinked.
S
Adjust the height of the flux nozzle above the weld so that the correct amount of
flux is delivered.
Flux coverage should be sufficient so that penetration of the arc does not occur.
5.3
S
Conversion of A2 SFE1 (Submerged arc welding) to MIG/MAG
welding
Assemble in accordance with the instructions accompanying the conversion kit.
5.4
S
Conversion of A2 SFE1 (Submerged arc welding) to Twin--arc
Assemble in accordance with the instructions accompanying the conversion kit.
6
MAINTENANCE
6.1
General
NB! Before doing any kind of maintenance work, make sure the mains is
disconnected.
For the maintenance of the A2--A6 Process Controller (PEH), see the instruction
manual.
6.2
S
S
S
S
Daily
Clean flux and dirt off moving parts of the welding machine.
Check that the contact tip and all electrical cables are connected.
Check that all bolted joints are tight and that guides and drive rollers are not
worn or damaged.
Check the brake hub braking torque. It should not be so low, that the wire reel
continues to rotate when wire feed is stopped and it should not be so great that
the feed rollers slip. As a guide, the braking torque for a 30 kg wire reel should
be 1.5 Nm.
Adjusting the braking torque:
S Set the locking button (2) to the
locked position.
S Insert a screwdriver into the hub
springs.
S Turning the springs (1) clockwise
reduces the braking torque.
S Turning the springs anticlockwise increases the torque.
NOTE! Turn the springs by the same amount.
dha5d1ea
-- 70 --
GB
6.3
Regularly
S
Check the wire feed motor brushes once every three months. Replace when
they are worn down to 6 mm.
S
Examine the slides and lubricate if they bind.
S
Inspect the wire guides, drive rollers and contact tip on the wire feed unit.
Replace any worn or damaged components, (see spare parts list on page 179).
7
FAULT TRACING
Equipment S
Instruction manual for A2--A6 Process Controller.
Check
S
that the power supply is connected for the correct mains supply
S
that all three phases are supplying the correct voltage
(phase sequence is not important)
S
that welding cables and connections are not damaged
S
that the controls are correctly set
S
that the mains supply is disconnected before starting repairs
POSSIBLE FAULTS
1. Symptom Current and voltage readings show large fluctuations
Cause 1.1
Contact jaws or nozzle are worn or wrong size.
Action
Replace contact jaws or nozzle.
Cause 1.2
Feed roller pressure is inadequate.
Action
Increase pressure on feed rollers.
2. Symptom Wire feed is irregular
Cause 2.1
Pressure on feed rollers incorrectly set.
Action
Pressure on feed rollers incorrectly set.
Cause 2.2
Feed rollers wrong size.
Action
Replace feed rollers.
Cause 2.3
Grooves in feed rollers are worn.
Action
Replace feed rollers.
3. Symptom Welding cables overheating
Cause 3.1
Poor electrical connection.
Action
Clean and tighten all electrical connections.
Cause 3.2
Cross--sectional area of welding cables too small.
Action
Use cables with a larger cross--section or use parallel cables.
dha5d1ea
-- 71 --
GB
8
ACCESSORIES
Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0413 518 880
Angular slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0413 506 880
Contact equipment for twin wire 2x1.2 -- 2x2.0 Light duty . . . . . . . . . . . . . . . . . 0333 852 881
Fine--wire straightener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0332 565 880
Conversion kit A2 SFE1 to MIG/MAG welding . . . . . . . . . . . . . . . . . . . . . . . . . . . 0413 526 881
Conversion kit A2 SFE1 to Twin with fine--wire straightener (LD) . . . . . . . . . . . 0413 541 882
Pilot lamp (D20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0153 143 886
Adapter M6/M10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0147 333 001
9
ORDERING OF SPARE PARTS
Spare parts are ordered through your nearest ESAB representative, see back cover.
When ordering spare parts, please state machine type and number as well as designation and spare part number as shown in the spare parts list on page 179.
This will simplify dispatch and ensure you get the right part.
dha5d1ea
-- 72 --
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising