Texas Instruments | LM4562 Dual High Performance, High Fidelity Audio Operational Amplifier (Rev. K) | Datasheet | Texas Instruments LM4562 Dual High Performance, High Fidelity Audio Operational Amplifier (Rev. K) Datasheet

Texas Instruments LM4562 Dual High Performance, High Fidelity Audio Operational Amplifier (Rev. K) Datasheet
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
LM4562 Dual High-Performance, High-Fidelity Audio Operational Amplifier
Check for Samples: LM4562
FEATURES
DESCRIPTION
•
•
•
•
•
The LM4562 is part of the ultra-low distortion, lownoise, high-slew-rate operational amplifier series
optimized and fully specified for high-performance,
high-fidelity applications. The LM4562 audio
operational amplifiers deliver superior audio signal
amplification for outstanding audio performance. The
LM4562 combines extremely low voltage noise
density (2.7nV/√Hz) with vanishingly low THD+N
(0.00003%) to easily satisfy the most demanding
audio applications. To ensure that the most
challenging loads are driven without compromise, the
LM4562 has a high slew rate of ±20V/μs and an
output current capability of ±26mA. Further, dynamic
range is maximized by an output stage that drives
2kΩ loads to within 1V of either power supply voltage
and to within 1.4V when driving 600Ω loads.
1
2
Easily Drives 600Ω Loads
Optimized for Superior Audio Signal Fidelity
Output Short Circuit Protection
PSRR and CMRR Exceed 120dB (Typ)
SOIC, PDIP, and TO-99 Packages
APPLICATIONS
•
•
•
•
•
Ultra High-Quality Audio Amplification
High-Fidelity Preamplifiers
High-Performance Professional Audio
High-Fidelity Active Equalization and
Crossover Networks
High-Performance Line Drivers and Receivers
KEY SPECIFICATIONS
•
•
•
•
•
•
•
•
•
Power Supply Voltage Range: ±2.5V to ± 17V
THD+N (AV = 1, VOUT = 3VRMS, fIN = 1kHz)
– RL = 2kΩ: 0.00003% (typ)
– RL = 600Ω: 0.00003% (typ)
Input Noise Density: 2.7nV/√Hz (typ)
Slew Rate: ±20V/μs (typ)
Gain Bandwidth Product: 55MHz (typ)
Open Loop Gain (RL = 600Ω): 140dB (typ)
Input Bias Current: 10nA (typ)
Input Offset Voltage: 0.1mV (typ)
DC Gain Linearity Error: 0.000009%
The LM4562's outstanding CMRR (120dB), PSRR
(120dB), and VOS (0.1mV) give the amplifier excellent
operational amplifier DC performance.
The LM4562 has a wide supply range of ±2.5V to
±17V. Over this supply range the LM4562’s input
circuitry maintains excellent common-mode and
power supply rejection, as well as maintaining its low
input bias current. The LM4562 is unity gain stable.
This
Audio
Operational
Amplifier
achieves
outstanding AC performance while driving complex
loads with values as high as 100pF.
The LM4562 is available in an 8-lead narrow body
SOIC, an 8-lead PDIP, and an 8-lead TO-99.
TYPICAL APPLICATION
150:
3320:
150:
3320:
26.1 k:
+
909:
-
-
LM4562
+
INPUT
LM4562
22 nF//4.7 nF//500 pF
10 pF
47 k:
+
3.83 k:
+
100:
OUTPUT
47 nF//33 nF
A.
1% metal film resistors, 5% polypropylene capacitors
Passively Equalized RIAA Phono Preamplifier
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
CONNECTION DIAGRAMS
+
Dual-In-Line Package
V
8
1
8
OUTPUT A
2
OUTPUT A
INVERTING
INPUT A
7
INVERTING INPUT A
1
OUTPUT B
7
2
6
INVERTING
INPUT B
OUTPUT B
A
NON-INVERTING
INPUT A
3
-
4
V
+
V
NON-INVERTING
INPUT A
B
+
+
-
3
5
NON-INVERTING
INPUT B
4
6
INVERTING INPUT B
V
5
-
NON-INVERTING
INPUT B
Figure 1. 8-Lead SOIC (D Package)
8-Lead PDIP (P Package)
Figure 2. 8-Lead TO-99 (LMC Package)
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS (1) (2) (3)
Power Supply Voltage (VS = V+ - V-)
36V
−65°C to 150°C
Storage Temperature
Input Voltage
(V-) - 0.7V to (V+) + 0.7V
Output Short Circuit
(4)
Continuous
Power Dissipation
Internally Limited
ESD Susceptibility (5)
ESD Susceptibility
(6)
2000V
Pins 1, 4, 7 and 8
Pins 2, 3, 5 and 6
Junction Temperature
Thermal Resistance
200V
100V
150°C
θJA (D)
145°C/W
θJA (P)
102°C/W
θJA (LMC)
150°C/W
θJC (LMC)
35°C/W
Temperature Range (TMIN ≤ TA ≤ TMAX)
–40°C ≤ TA ≤ 85°C
Supply Voltage Range
±2.5V ≤ VS ≤ ± 17V
(1)
(2)
(3)
(4)
(5)
(6)
2
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured
specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed.
Some performance characteristics may degrade when the device is not operated under the listed test conditions.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Amplifier output connected to GND, any number of amplifiers within a package.
Human body model, 100pF discharged through a 1.5kΩ resistor.
Machine Model ESD test is covered by specification EIAJ IC-121-1981. A 200pF cap is charged to the specified voltage and then
discharged directly into the IC with no external series resistor (resistance of discharge path must be under 50Ω).
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
ELECTRICAL CHARACTERISTICS FOR THE LM4562 (1) (2)
The specifications apply for VS = ±15V, RL = 2kΩ, fIN = 1kHz, TA = 25°C, unless otherwise specified.
Symbol
THD+N
Parameter
Total Harmonic Distortion + Noise
Conditions
LM4562
Typical
(3)
AV = 1, VOUT = 3Vrms
RL = 2kΩ
RL = 600Ω
0.00003
0.00003
AV = 1, VOUT = 3VRMS
Two-tone, 60Hz & 7kHz 4:1
0.00005
Limit (4)
Units
(Limits)
% (max)
0.00009
IMD
Intermodulation Distortion
GBWP
Gain Bandwidth Product
55
45
MHz (min)
SR
Slew Rate
±20
±15
V/μs (min)
FPBW
Full Power Bandwidth
VOUT = 1VP-P, –3dB
referenced to output magnitude
at f = 1kHz
10
MHz
ts
Settling time
AV = –1, 10V step, CL = 100pF
0.1% error range
1.2
μs
Equivalent Input Noise Voltage
fBW = 20Hz to 20kHz
0.34
0.65
μVRMS
(max)
Equivalent Input Noise Density
f = 1kHz
f = 10Hz
2.7
6.4
4.7
nV/√Hz
(max)
in
Current Noise Density
f = 1kHz
f = 10Hz
1.6
3.1
VOS
Offset Voltage
ΔVOS/ΔTemp
Average Input Offset Voltage Drift vs
Temperature
–40°C ≤ TA ≤ 85°C
0.2
PSRR
Average Input Offset Voltage Shift vs
Power Supply Voltage
ΔVS = 20V (5)
120
ISOCH-CH
Channel-to-Channel Isolation
fIN = 1kHz
fIN = 20kHz
118
112
IB
Input Bias Current
VCM = 0V
10
ΔIOS/ΔTemp
Input Bias Current Drift vs
Temperature
–40°C ≤ TA ≤ 85°C
0.1
IOS
Input Offset Current
VCM = 0V
en
VIN-CM
CMRR
Common-Mode Rejection
Common Mode Input Impedance
AVOL
VOUTMAX
IOUT
Open Loop Voltage Gain
Maximum Output Voltage Swing
Output Current
IOUT-CC
Instantaneous Short Circuit Current
ROUT
Output Impedance
(3)
(4)
(5)
pA/√Hz
±0.7
mV (max)
μV/°C
110
dB (min)
dB
72
nA (max)
nA/°C
11
65
nA (max)
+14.1
–13.9
(V+) – 2.0
(V-) + 2.0
V (min)
–10V<Vcm<10V
120
110
dB (min)
30
kΩ
–10V<Vcm<10V
1000
MΩ
–10V<Vout<10V, RL = 600Ω
140
–10V<Vout<10V, RL = 2kΩ
140
–10V<Vout<10V, RL = 10kΩ
140
Common-Mode Input Voltage Range
Differential Input Impedance
ZIN
(1)
(2)
±0.1
%
RL = 600Ω
±13.6
RL = 2kΩ
±14.0
RL = 10kΩ
±14.1
RL = 600Ω, VS = ±17V
±26
125
dB (min)
±12.5
V (min)
±23
mA (min)
+53
–42
fIN = 10kHz
Closed-Loop
Open-Loop
0.01
13
mA
Ω
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured
specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed.
Some performance characteristics may degrade when the device is not operated under the listed test conditions.
Typical specifications are specified at +25ºC and represent the most likely parametric norm.
Tested limits are specified to AOQL (Average Outgoing Quality Level).
PSRR is measured as follows: VOS is measured at two supply voltages, ±5V and ±15V. PSRR = | 20log(ΔVOS/ΔVS) |.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
3
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS FOR THE LM4562(1)(2) (continued)
The specifications apply for VS = ±15V, RL = 2kΩ, fIN = 1kHz, TA = 25°C, unless otherwise specified.
Symbol
Parameter
Conditions
LM4562
Typical
CLOAD
Capacitive Load Drive Overshoot
100pF
16
IS
Total Quiescent Current
IOUT = 0mA
10
4
Submit Documentation Feedback
(3)
Limit (4)
Units
(Limits)
12
mA (max)
%
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS
0.01
THD+N vs Output Voltage
VCC = 15V, VEE = –15V
RL = 2kΩ
0.01
0.005
0.005
0.002
0.002
0.001
THD+N (%)
THD+N (%)
0.001
0.0005
0.0002
0.0005
0.0002
0.0001
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
10m
100m
1
0.00001
10m
10 20
OUTPUT VOLTAGE (V)
Figure 3.
Figure 4.
THD+N vs Output Voltage
VCC = 17V, VEE = –17V
RL = 2kΩ
THD+N vs Output Voltage
VCC = 2.5V, VEE = –2.5V
RL = 2kΩ
0.01
0.005
0.005
0.002
0.002
0.001
0.001
0.0005
0.0002
0.0001
0.0005
0.0002
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
10m
10 20
1
100m
OUTPUT VOLTAGE (V)
THD + N (%)
THD+N (%)
0.01
THD+N vs Output Voltage
VCC = 12V, VEE = –12V
RL = 2kΩ
100m
1
0.00001
100m 200m
10 20
500m
1
2
5
10
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
0.01
Figure 5.
Figure 6.
THD+N vs Output Voltage
VCC = 15V, VEE = –15V
RL = 600Ω
THD+N vs Output Voltage
VCC = 12V, VEE = –12V
RL = 600Ω
0.01
0.005
0.005
0.002
0.002
0.001
THD+N (%)
THD+N (%)
0.001
0.0005
0.0002
0.0005
0.0002
0.0001
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
10m
100m
1
10 20
0.00001
10m
100m
1
10 20
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
5
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
0.01
THD+N vs Output Voltage
VCC = 17V, VEE = –17V
RL = 600Ω
THD+N vs Output Voltage
VCC = 2.5V, VEE = –2.5V
RL = 600Ω
0.01
0.005
0.005
0.002
0.002
0.001
THD + N (%)
THD+N (%)
0.001
0.0005
0.0002
0.0001
0.0005
0.0002
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
10m
100m
1
0.00001
100m 200m
10 20
OUTPUT VOLTAGE (V)
THD+N vs Output Voltage
VCC = 15V, VEE = –15V
RL = 10kΩ
THD+N vs Output Voltage
VCC = 12V, VEE = –12V
RL = 10kΩ
0.01
0.002
0.002
0.001
0.001
0.0005
0.0002
0.0002
0.0001
0.00005
0.00005
0.00002
0.00002
100m
1
0.00001
10m
10 20
100m
OUTPUT VOLTAGE (V)
1
10 20
OUTPUT VOLTAGE (V)
Figure 11.
Figure 12.
THD+N vs Output Voltage
VCC = 17V, VEE = –17V
RL = 10kΩ
THD+N vs Output Voltage
VCC = 2.5V, VEE = –2.5V
RL = 10kΩ
0.01
0.005
0.005
0.002
0.002
0.001
0.001
THD + N (%)
THD+N (%)
10
0.0005
0.0001
0.0005
0.0002
0.0001
0.0005
0.0002
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
10m
5
Figure 10.
0.005
0.01
2
OUTPUT VOLTAGE (V)
0.005
0.00001
10m
1
Figure 9.
THD+N (%)
THD+N (%)
0.01
500m
100m
1
10 20
0.00001
100m 200m
500m
1
2
5
10
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Figure 13.
6
Figure 14.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
THD+N vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS
RL = 2kΩ
THD+N vs Frequency
VCC = 12V, VEE = –12V, VOUT = 3VRMS
RL = 2kΩ
0.01
0.005
0.005
0.002
0.002
0.001
0.001
0.0005
0.0005
%
%
0.01
0.0002
0.0002
0.0001
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
20
50 100 200 500 1k 2k
0.00001
20
5k 10k 20k
50 100 200 500 1k 2k
5k 10k 20k
Hz
Hz
Figure 15.
Figure 16.
THD+N vs Frequency
VCC = 17V, VEE = –17V, VOUT = 3VRMS
RL = 2kΩ
THD+N vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS
RL = 600Ω
0.01
0.01
0.005
0.005
0.002
0.002
0.001
0.0005
0.0005
%
%
0.001
0.0002
0.0002
0.0001
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
20
50 100 200 500 1k 2k
0.00001
20
5k 10k 20k
50 100 200 500 1k 2k
5k 10k 20k
Hz
Hz
Figure 17.
Figure 18.
THD+N vs Frequency
VCC = 12V, VEE = –12V, VOUT = 3VRMS
RL = 600Ω
THD+N vs Frequency
VCC = 17V, VEE = –17V, VOUT = 3VRMS
RL = 600Ω
0.005
0.005
0.002
0.002
0.001
0.001
0.0005
0.0005
%
0.01
%
0.01
0.0002
0.0002
0.0001
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
20
50 100 200 500 1k 2k
5k 10k 20k
0.00001
20
Hz
50 100 200 500 1k 2k
5k 10k 20k
Hz
Figure 19.
Figure 20.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
7
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
THD+N vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS
RL = 10kΩ
THD+N vs Frequency
VCC = 12V, VEE = –12V, VOUT = 3VRMS
RL = 10kΩ
0.002
0.002
0.001
0.001
0.0005
0.0005
%
0.01
0.005
%
0.01
0.005
0.0002
0.0002
0.0001
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
20
50 100 200 500 1k 2k
5k 10k 20k
0.00001
20
Hz
50 100 200 500 1k 2k
5k 10k 20k
Hz
Figure 21.
Figure 22.
THD+N vs Frequency
VCC = 17V, VEE = –17V, VOUT = 3VRMS
RL = 10kΩ
IMD vs Output Voltage
VCC = 15V, VEE = –15V
RL = 2kΩ
0.01
0.01
0.005
0.005
0.002
0.002
0.001
0.0005
0.0005
%
IMD (%)
0.001
0.0002
0.0002
0.0001
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
20
50 100 200 500 1k 2k
0.00001
0.000007
100m 200m 500m 1
5k 10k 20k
Figure 24.
IMD vs Output Voltage
VCC = 12V, VEE = –12V
RL = 2kΩ
IMD vs Output Voltage
VCC = 2.5V, VEE = –2.5V
RL = 2kΩ
0.01
0.005
0.005
0.002
0.002
0.001
0.001
0.0005
0.0002
10
0.0005
0.0002
0.0001
0.0001
0.00005
0.00005
0.00002
0.00001
0.000007
100m 200m 500m 1
0.00002
2
5
10
0.00001
100m 200m 500m 1
OUTPUT VOLTAGE (V)
2
5
10
OUTPUT VOLTAGE (V)
Figure 25.
8
5
Figure 23.
IMD (%)
IMD (%)
0.01
2
OUTPUT VOLTAGE (V)
Hz
Figure 26.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
0.01
0.005
0.005
0.002
0.002
0.001
0.001
0.0005
0.0005
IMD (%)
IMD (%)
0.01
IMD vs Output Voltage
VCC = 17V, VEE = –17V
RL = 2kΩ
0.0002
0.0001
0.0002
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
0.000007
100m 200m 500m 1
2
5
0.00001
0.000006
100m 200m 500m 1
10
OUTPUT VOLTAGE (V)
Figure 28.
IMD vs Output Voltage
VCC = 12V, VEE = –12V
RL = 600Ω
IMD vs Output Voltage
VCC = 17V, VEE = –17V
RL = 600Ω
0.01
0.005
0.002
0.002
0.001
0.001
0.0005
0.0005
0.0002
0.0001
10
0.0002
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
0.000006
100m 200m 500m 1
2
5
0.00001
0.000007
100m 200m 500m 1
10
2
5
10
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Figure 29.
Figure 30.
IMD vs Output Voltage
VCC = 2.5V, VEE = –2.5V
RL = 600Ω
IMD vs Output Voltage
VCC = 15V, VEE = –15V
RL = 10kΩ
0.01
0.005
0.005
0.002
0.002
0.001
IMD (%)
0.001
IMD (%)
5
Figure 27.
0.005
0.01
2
OUTPUT VOLTAGE (V)
IMD (%)
IMD (%)
0.01
IMD vs Output Voltage
VCC = 15V, VEE = –15V
RL = 600Ω
0.0005
0.0002
0.0001
0.0005
0.0002
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
100m
300m
500m 700m
1
0.00001
0.000006
100m 200m 500m 1
2
5
10
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Figure 31.
Figure 32.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
9
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
IMD vs Output Voltage
VCC = 12V, VEE = –12V
RL = 10kΩ
0.01
0.005
0.005
0.002
0.002
0.001
0.001
0.0005
0.0005
IMD (%)
IMD (%)
0.01
0.0002
0.0001
0.0002
0.0001
0.00005
0.00005
0.00002
0.00002
0.00001
0.000006
100m 200m 500m 1
2
5
IMD vs Output Voltage
VCC = 17V, VEE = –17V
RL = 10kΩ
0.00001
0.000006
100m 200m 500m 1
10
OUTPUT VOLTAGE (V)
Figure 33.
5
10
Figure 34.
IMD vs Output Voltage
VCC = 2.5V, VEE = –2.5V
RL = 10kΩ
Voltage Noise Density vs Frequency
100
100
0.01
VOLTAGE NOISE (nV/ Hz)
0.005
0.002
0.001
IMD (%)
2
OUTPUT VOLTAGE (V)
0.0005
0.0002
0.0001
VS = 30V
VCM = 15V
10
10
2.7 nV/ Hz
0.00005
0.00002
1
0.00001
100m
300m
500m 700m
1
1
10
100
1000
1
10000 100000
FREQUENCY (Hz)
OUTPUT VOLTAGE (V)
Figure 35.
Figure 36.
Current Noise Density vs Frequency
Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS
AV = 0dB, RL = 2kΩ
+0
100
100
VCM = 15V
10
10
CROSSTALK (dB)
CURRENT NOISE (pA/ Hz)
VS = 30V
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
1
1.6 pA/ Hz
1
10
100
1000
1
10000 100000
FREQUENCY (Hz)
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
Figure 37.
10
-120
-130
20
Figure 38.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 3VRMS
AV = 0dB, RL = 2kΩ
+0
+0
-10
-20
-30
-40
-50
-10
-20
-30
-40
-50
CROSSTALK (dB)
CROSSTALK (dB)
Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 10VRMS
AV = 0dB, RL = 2kΩ
-60
-70
-80
-90
-60
-70
-80
-90
-100
-100
-110
-110
-120
-130
20
-120
-130
20
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
Figure 40.
Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 10VRMS
AV = 0dB, RL = 2kΩ
Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 3VRMS
AV = 0dB, RL = 2kΩ
+0
+0
-10
-20
-30
-40
-50
-10
-20
-30
-40
-50
-60
-70
-80
-90
-60
-70
-80
-90
-100
-100
-110
-110
-120
-130
20
-120
-130
20
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
Figure 41.
Figure 42.
Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 10VRMS
AV = 0dB, RL = 2kΩ
Crosstalk vs Frequency
VCC = 2.5V, VEE = –2.5V, VOUT = 1VRMS
AV = 0dB, RL = 2kΩ
+0
-10
-20
+0
-10
-20
-30
-40
-50
CROSSTALK (dB)
CROSSTALK (dB)
5k 10k 20k
Figure 39.
CROSSTALK (dB)
CROSSTALK (dB)
FREQUENCY (Hz)
50 100 200 500 1k 2k
-60
-70
-80
-90
-100
-50
-60
-70
-80
-90
-100
-110
-120
-110
-120
-130
20
-30
-40
-130
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
20
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
Figure 43.
Figure 44.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
11
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 10VRMS
AV = 0dB, RL = 600Ω
+0
+0
-10
-20
-30
-40
-50
-10
-20
-30
-40
-50
CROSSTALK (dB)
CROSSTALK (dB)
Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS
AV = 0dB, RL = 600Ω
-60
-70
-80
-90
-60
-70
-80
-90
-100
-100
-110
-110
-120
-130
20
-120
-130
20
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
Figure 46.
Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 3VRMS
AV = 0dB, RL = 600Ω
Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 10VRMS
AV = 0dB, RL = 600Ω
+0
+0
-10
-20
-30
-40
-50
-10
-20
-30
-40
-50
-60
-70
-80
-90
-60
-70
-80
-90
-100
-100
-110
-110
-120
-130
20
-120
-130
20
50 100 200 500 1k 2k
5k 10k 20k
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
Figure 47.
Figure 48.
Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 3VRMS
AV = 0dB, RL = 600Ω
Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 10VRMS
AV = 0dB, RL = 600Ω
+0
+0
-10
-20
-30
-40
-50
-10
-20
-30
-40
-50
CROSSTALK (dB)
CROSSTALK (dB)
FREQUENCY (Hz)
-60
-70
-80
-90
-60
-70
-80
-90
-100
-100
-110
-110
-120
-130
20
-120
-130
20
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
Figure 49.
12
5k 10k 20k
Figure 45.
CROSSTALK (dB)
CROSSTALK (dB)
FREQUENCY (Hz)
50 100 200 500 1k 2k
Figure 50.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Crosstalk vs Frequency
VCC = 2.5V, VEE = –2.5V, VOUT = 1VRMS
AV = 0dB, RL = 600Ω
Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS
AV = 0dB, RL = 10kΩ
CROSSTALK (dB)
CROSSTALK (dB)
+0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
20
50 100 200 500 1k 2k
5k 10k 20k
+0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
5k 10k 20k
FREQUENCY (Hz)
Figure 52.
Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 10VRMS
AV = 0dB, RL = 10kΩ
Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 3VRMS
AV = 0dB, RL = 10kΩ
+0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
CROSSTALK (dB)
Figure 51.
50 100 200 500 1k 2k
5k 10k 20k
+0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 53.
Figure 54.
Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 10VRMS
AV = 0dB, RL = 10kΩ
Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 3VRMS
AV = 0dB, RL = 10kΩ
+0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
CROSSTALK (dB)
CROSSTALK (dB)
CROSSTALK (dB)
FREQUENCY (Hz)
50 100 200 500 1k 2k
50 100 200 500 1k 2k
5k 10k 20k
+0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
50 100 200 500 1k 2k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 55.
Figure 56.
5k 10k 20k
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
13
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CROSSTALK (dB)
+0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
Crosstalk vs Frequency
VCC = 2.5V, VEE = –2.5V, VOUT = 1VRMS
AV = 0dB, RL = 10kΩ
50 100 200 500 1k 2k
5k 10k 20k
+0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
50 100 200 500 1k 2k
FREQUENCY (Hz)
Figure 57.
Figure 58.
PSRR+ vs Frequency
VCC = 15V, VEE = –15V
RL = 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
PSRR- vs Frequency
VCC = 15V, VEE = –15V
RL = 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
100
1k
10k
-110
-120
-130
-140
20
100k 200k
100
10k
100k 200k
Figure 59.
Figure 60.
PSRR+ vs Frequency
VCC = 15V, VEE = –15V
RL = 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
PSRR- vs Frequency
VCC = 15V, VEE = –15V
RL = 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
PSRR (dB)
PSRR (dB)
1k
FREQUENCY (Hz)
FREQUENCY (Hz)
100
1k
10k
100k 200k
-110
-120
-130
-140
20
100
1k
10k
100k 200k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 61.
14
5k 10k 20k
FREQUENCY (Hz)
PSRR (dB)
PSRR (dB)
CROSSTALK (dB)
Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 10VRMS
AV = 0dB, RL = 10kΩ
Figure 62.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
PSRR- vs Frequency
VCC = 15V, VEE = –15V
RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
PSRR (dB)
PSRR (dB)
PSRR+ vs Frequency
VCC = 15V, VEE = –15V
RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp
100
1k
10k
-110
-120
-130
-140
20
100k 200k
100
100k 200k
Figure 64.
PSRR+ vs Frequency
VCC = 12V, VEE = –12V
RL = 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
PSRR– vs Frequency
VCC = 12V, VEE = –12V
RL = 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
100
1k
10k
-110
-120
-130
-140
20
100k 200k
100
FREQUENCY (Hz)
1k
10k
FREQUENCY (Hz)
100k 200k
Figure 65.
Figure 66.
PSRR+ vs Frequency
VCC = 12V, VEE = –12V
RL = 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
PSRR– vs Frequency
VCC = 12V, VEE = –12V
RL = 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
PSRR (dB)
PSRR (dB)
1k
10k
FREQUENCY (Hz)
Figure 63.
PSRR (dB)
PSRR (dB)
FREQUENCY (Hz)
100
1k
10k
FREQUENCY (Hz)
100k 200k
-110
-120
-130
-140
20
100
1k
10k
100k 200k
FREQUENCY (Hz)
Figure 67.
Figure 68.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
15
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
PSRR– vs Frequency
VCC = 12V, VEE = –12V
RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
PSRR (dB)
PSRR (dB)
PSRR+ vs Frequency
VCC = 12V, VEE = –12V
RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp
100
1k
10k
-110
-120
-130
-140
20
100k 200k
100
PSRR (dB)
100k 200k
Figure 70.
PSRR+ vs Frequency
VCC = 17V, VEE = –17V
RL = 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
PSRR– vs Frequency
VCC = 17V, VEE = –17V
RL = 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
PSRR (dB)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
100
1k
10k
FREQUENCY (Hz)
-110
-120
-130
-140
20
100k 200k
100
1k
10k
FREQUENCY (Hz)
100k 200k
Figure 71.
Figure 72.
PSRR+ vs Frequency
VCC = 17V, VEE = –17V
RL = 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
PSRR– vs Frequency
VCC = 17V, VEE = –17V
RL = 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
100
1k
10k
FREQUENCY (Hz)
100k 200k
Figure 73.
16
1k
10k
FREQUENCY (Hz)
Figure 69.
PSRR (dB)
PSRR (dB)
FREQUENCY (Hz)
-110
-120
-130
-140
20
100
1k
10k
FREQUENCY (Hz)
100k 200k
Figure 74.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
PSRR+ vs Frequency
VCC = 17V, VEE = –17V
RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp
PSRR– vs Frequency
VCC = 17V, VEE = –17V
RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp
-110
-120
-130
-140
20
PSRR (dB)
PSRR (dB)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
100
1k
10k
FREQUENCY (Hz)
-110
-120
-130
-140
20
100k 200k
1k
10k
100k 200k
Figure 75.
Figure 76.
PSRR+ vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
PSRR– vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
0
PSRR (dB)
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
100
1k
10k
FREQUENCY (Hz)
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
100k 200k
100
1k
10k
FREQUENCY (Hz)
100k 200k
Figure 77.
Figure 78.
PSRR+ vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
PSRR– vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
PSRR (dB)
PSRR (dB)
100
FREQUENCY (Hz)
0
PSRR (dB)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
100
1k
10k
100k 200k
FREQUENCY (Hz)
Figure 79.
-110
-120
-130
-140
20
100
1k
10k
FREQUENCY (Hz)
100k 200k
Figure 80.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
17
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
PSRR– vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
PSRR (dB)
PSRR (dB)
PSRR+ vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp
100
1k
10k
-110
-120
-130
-140
20
100k 200k
100
CMRR vs Frequency
VCC = 15V, VEE = –15V
RL = 2kΩ
CMRR vs Frequency
VCC = 12V, VEE = –12V
RL = 2kΩ
-20
-40
-40
CMRR (dB)
-20
-60
-60
-80
-80
-100
-100
100
1k
10k
-120
10
100k 200k
100
1k
10k
100k 200k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 83.
Figure 84.
CMRR vs Frequency
VCC = 17V, VEE = –17V
RL = 2kΩ
CMRR vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 2kΩ
0
0
-20
-20
-40
-40
CMRR (dB)
CMRR (dB)
CMRR (dB)
18
100k 200k
Figure 82.
0
-60
-60
-80
-80
-100
-100
-120
10
10k
Figure 81.
0
-120
10
1k
FREQUENCY (Hz)
FREQUENCY (Hz)
100
1k
10k
100k 200k
-120
10
100
1k
10k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 85.
Figure 86.
Submit Documentation Feedback
100k 200k
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
0
-20
-20
-40
-40
-60
-60
-80
-80
-100
-100
100
1k
10k
FREQUENCY (Hz)
-120
10
100k 200k
10k
100k 200k
Figure 88.
CMRR vs Frequency
VCC = 17V, VEE = –17V
RL = 600Ω
CMRR vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 600Ω
0
-20
-20
-40
-40
-60
-60
-80
-80
-100
-100
100
1k
10k
-120
10
100k 200k
100
1k
10k
100k 200k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 89.
Figure 90.
CMRR vs Frequency
VCC = 15V, VEE = –15V
RL = 10kΩ
CMRR vs Frequency
VCC = 12V, VEE = –12V
RL = 10kΩ
0
0
-20
-20
-40
-40
-60
-60
-80
-80
-100
-100
-120
10
1k
Figure 87.
0
-120
10
100
FREQUENCY (Hz)
CMRR (dB)
CMRR (dB)
CMRR (dB)
0
-120
10
CMRR (dB)
CMRR vs Frequency
VCC = 12V, VEE = –12V
RL = 600Ω
CMRR (dB)
CMRR (dB)
CMRR vs Frequency
VCC = 15V, VEE = –15V
RL = 600Ω
100
1k
10k
FREQUENCY (Hz)
100k 200k
-120
10
100
1k
10k
100k 200k
FREQUENCY (Hz)
Figure 91.
Figure 92.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
19
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CMRR vs Frequency
VCC = 2.5V, VEE = –2.5V
RL = 10kΩ
0
-20
-20
-40
-40
CMRR (dB)
0
-60
-60
-80
-80
-100
-100
OUTPUT (Vrms)
-120
10
100
1k
10k
100k 200k
-120
10
100
1k
10k
100k 200k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 93.
Figure 94.
Output Voltage vs Load Resistance
VDD = 15V, VEE = –15V
THD+N = 1%
Output Voltage vs Load Resistance
VDD = 12V, VEE = –12V
THD+N = 1%
11.5
9.5
11.0
9.0
OUTPUT (Vrms)
CMRR (dB)
CMRR vs Frequency
VCC = 17V, VEE = –17V
RL = 10kΩ
10.5
10.0
8.0
7.5
9.5
9.0
8.5
500
600
800
2k
5k
7.0
10k
500
600
800
2k
5k
10k
LOAD RESISTANCE (:)
LOAD RESISTANCE (:)
Figure 95.
Figure 96.
Output Voltage vs Load Resistance
VDD = 17V, VEE = –17V
THD+N = 1%
Output Voltage vs Load Resistance
VDD = 2.5V, VEE = –2.5V
THD+N = 1%
1.25
13.5
13.0
1.00
OUTPUT (Vrms)
OUTPUT (Vrms)
12.5
12.0
11.5
0.75
0.25
11.0
0.50
10.5
10.0
0.00
500
600
800
2k
5k
10k
Figure 97.
20
500
600
800
2k
5k
10k
LOAD RESISTANCE (:)
LOAD RESISTANCE (:)
Figure 98.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
14
Output Voltage vs Supply Voltage
RL = 2kΩ, THD+N = 1%
12
10
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
12
10
8
6
4
8
6
4
2
2
0
2.5
14
Output Voltage vs Supply Voltage
RL = 600Ω, THD+N = 1%
4.5
6.5
0
2.5
8.5 10.5 12.5 14.5 16.5 18.5
4.5
6.5
8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 99.
Figure 100.
Output Voltage vs Supply Voltage
RL = 10kΩ, THD+N = 1%
Supply Current vs Supply Voltage
RL = 2kΩ
10.5
SUPPLY CURRENT (mA)
OUTPUT VOLTAGE (V)
12
10
8
6
4
10.0
9.5
9.0
8.5
2
0
2.5
6.5
8.0
2.5
8.5 10.5 12.5 14.5 16.5 18.5
8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
Figure 101.
Figure 102.
Supply Current vs Supply Voltage
RL = 600Ω
10.0
9.5
9.0
8.5
8.0
2.5
4.5 6.5
SUPPLY VOLTAGE (V)
10.5
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
10.5
4.5
4.5 6.5
8.5 10.5 12.5 14.5 16.5 18.5
Supply Current vs Supply Voltage
RL = 10kΩ
10.0
9.5
9.0
8.5
8.0
2.5 4.5
6.5
8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 103.
Figure 104.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
21
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Full Power Bandwidth vs Frequency
0
160
o
GAIN (dB), PHASE LAG ( )
180
-2
MAGNITUDE (dB)
Gain Phase vs Frequency
2
0 dB = 1 VP-P
-4
-6
-8
-10
-12
-14
140
120
100
80
60
40
20
-16
0
-18
-20
10
1
10
100
1k
10k 100k 1M 10M 100M
Figure 105.
Figure 106.
Small-Signal Transient Response
AV = 1, CL = 10pF
Small-Signal Transient Response
AV = 1, CL = 100pF
': 0.00s
': 0.00s
': 0.00V
@: -1.01 Ps @: -80.0 mV
': 0.00V
@: -1.01 Ps @: -80.0 mV
1
1
Ch1 50.0 mV
M 200 ns A Ch1
50.40%
2.00 mV
Figure 107.
22
10000000
100000
1000000 100000000
10000
FREQUENCY (Hz)
1000
100
FREQUENCY (Hz)
Ch1 50.0 mV
M 200 ns A Ch1
50.40%
2.00 mV
Figure 108.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
APPLICATION INFORMATION
DISTORTION MEASUREMENTS
The vanishingly low residual distortion produced by LM4562 is below the capabilities of all commercially available
equipment. This makes distortion measurements just slightly more difficult than simply connecting a distortion
meter to the amplifier’s inputs and outputs. The solution, however, is quite simple: an additional resistor. Adding
this resistor extends the resolution of the distortion measurement equipment.
The LM4562’s low residual distortion is an input referred internal error. As shown in Figure 109, adding the 10Ω
resistor connected between the amplifier’s inverting and non-inverting inputs changes the amplifier’s noise gain.
The result is that the error signal (distortion) is amplified by a factor of 101. Although the amplifier’s closed-loop
gain is unaltered, the feedback available to correct distortion errors is reduced by 101, which means that
measurement resolution increases by 101. To ensure minimum effects on distortion measurements, keep the
value of R1 low as shown in Figure 109.
This technique is verified by duplicating the measurements with high closed loop gain and/or making the
measurements at high frequencies. Doing so produces distortion components that are within the measurement
equipment’s capabilities. This datasheet’s THD+N and IMD values were generated using the above described
circuit connected to an Audio Precision System Two Cascade.
R2
1000:
LM4562
R1
10:
Distortion Signal Gain = 1+(R2/R1)
+
Analyzer Input
Generator Output
Audio Precision
System Two
Cascade
Actual Distortion = AP Value/100
Figure 109. THD+N and IMD Distortion Test Circuit
The LM4562 is a high-speed op amp with excellent phase margin and stability. Capacitive loads up to 100pF will
cause little change in the phase characteristics of the amplifiers and are therefore allowable.
Capacitive loads greater than 100pF must be isolated from the output. The most straightforward way to do this is
to put a resistor in series with the output. This resistor will also prevent excess power dissipation if the output is
accidentally shorted.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
23
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
A.
www.ti.com
Complete shielding is required to prevent induced pick up from external sources. Always check with oscilloscope for
power line noise.
Figure 110. Noise Measurement Circuit
Total Gain: 115 dB @f = 1 kHz
Input Referred Noise Voltage: en = V0/560,000 (V)
Figure 111. RIAA Preamp Voltage Gain, RIAA
Deviation vs Frequency
24
Figure 112. Flat Amp Voltage Gain vs Frequency
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
Evaluation Module Schematic
+VCC
JP3, pin 1
R8
10 kW
R7
10 kW
C3
C1
10 mF
0.1 mF
8
JP4, pin 1
7
6
5
3
4
–
+
+
–
1
2
R2
10 kW
JP1, pin 1
C2
0.1 mF
R3
10 kW
C4
10 mF
–VEE
JP2, pin 1
Figure 113. Inverting Amplifiers
Typical Applications
AV = 34.5
F = 1 kHz
En = 0.38 μV
A Weighted
Figure 114. NAB Preamp
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
25
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
Figure 115. NAB Preamp Voltage Gain vs Frequency
VO = V1–V2
Figure 116. Balanced to Single-Ended Converter
VO = V1 + V2 − V3 − V4
Figure 117. Adder/Subtracter
Figure 118. Sine Wave Oscillator
26
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
Illustration is f0 = 1 kHz
Figure 119. Second-Order High-Pass Filter (Butterworth)
Illustration is f0 = 1 kHz
Figure 120. Second-Order Low-Pass Filter (Butterworth)
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
27
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
Illustration is f0 = 1 kHz, Q = 10, ABP = 1
Figure 121. State Variable Filter
Figure 122. AC/DC Converter
Figure 123. 2-Channel Panning Circuit (Pan Pot)
28
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
Figure 124. Line Driver
fL|
fH|
1
1
, fLB|
2S R1C1
2S R 2 C1
1
1
, fHB|
2S R 5 C 2
2S ( R1 + R5 + 2R3) C2
The equations started above are simplifications, providing guidance of general –3dB point values, when the
potentiometers are at their null position.
Illustration is:
fL ≈ 32 Hz, fLB ≈ 320 Hz
fH ≈ 11 kHz, fHB ≈ 1.1 kHz
Figure 125. Tone Control
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
29
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
Av = 35 dB
En = 0.33 μV S/N = 90 dB
f = 1 kHz
A Weighted
A Weighted, VIN = 10 mV
@f = 1 kHz
Figure 126. RIAA Preamp
Illustration is:
V0 = 101(V2 − V1)
Figure 127. Balanced Input Mic Amp
30
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
A.
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
See Table 1.
Figure 128. 10-Band Graphic Equalizer
Table 1. C1, C2, R1, and R2 Values for Figure 128 (1)
(1)
fo (Hz)
C1
C2
R1
R2
32
0.12μF
4.7μF
75kΩ
500Ω
64
0.056μF
3.3μF
68kΩ
510Ω
125
0.033μF
1.5μF
62kΩ
510Ω
250
0.015μF
0.82μF
68kΩ
470Ω
500
8200pF
0.39μF
62kΩ
470Ω
1k
3900pF
0.22μF
68kΩ
470Ω
2k
2000pF
0.1μF
68kΩ
470Ω
4k
1100pF
0.056μF
62kΩ
470Ω
8k
510pF
0.022μF
68kΩ
510Ω
16k
330pF
0.012μF
51kΩ
510Ω
At volume of change = ±12 dB
Q = 1.7
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
31
LM4562
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
www.ti.com
REVISION HISTORY
Changes from Revision J (April 2013) to Revision K
•
32
Page
Added EVM schematic ....................................................................................................................................................... 25
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K – AUGUST 2006 – REVISED DECEMBER 2013
REVISION HISTORY
Rev
Date
1.0
08/16/06
Description
Initial release.
1.1
08/22/06
Updated the Instantaneous Short Circuit Current specification.
1.2
09/12/06
Updated the three ±15V CMRR Typical Performance Curves.
1.3
09/26/06
Updated interstage filter capacitor values on page 1 Typical Application
schematic.
1.4
05/03/07
Added the “general note” under the EC table.
1.5
10/17/07
Replaced all the PSRR curves.
1.6
01/26/10
Edited the equations on page 28 (under Tone Control).
J
04/04/13
Changed layout of National Data Sheet to TI format
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
33
PACKAGE OPTION ADDENDUM
www.ti.com
7-Nov-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4562MA/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
L4562
MA
LM4562MAX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
L4562
MA
LM4562NA/NOPB
ACTIVE
PDIP
P
8
40
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 85
LM
4562NA
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
7-Nov-2017
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Nov-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LM4562MAX/NOPB
Package Package Pins
Type Drawing
SOIC
D
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
6.5
B0
(mm)
K0
(mm)
P1
(mm)
5.4
2.0
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Nov-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM4562MAX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
A
.004 [0.1] C
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.150
[3.81]
.189-.197
[4.81-5.00]
NOTE 3
4X (0 -15 )
4
5
B
8X .012-.020
[0.31-0.51]
.010 [0.25]
C A B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 -8
.016-.050
[0.41-1.27]
DETAIL A
(.041)
[1.04]
TYPICAL
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
6X (.050 )
[1.27]
SYMM
5
4
(R.002 ) TYP
[0.05]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
METAL
SOLDER MASK
OPENING
EXPOSED
METAL
.0028 MAX
[0.07]
ALL AROUND
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
EXPOSED
METAL
.0028 MIN
[0.07]
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
6X (.050 )
[1.27]
SYMM
5
4
(R.002 ) TYP
[0.05]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising