Texas Instruments | VCA5807 Development | User Guides | Texas Instruments VCA5807 Development User guides

Texas Instruments VCA5807 Development User guides
User's Guide
SLOU352 – November 2012
VCA5807 Development Guide
This development guide describes the characteristics, operation and use of the VCA5807EVM
demonstration kit. This demonstration kit is an evaluation module for the VCA5807 device. The VCA5807
is an integrated Voltage Controlled Amplifier (VCA) that integrates a complete time-gain-control (TGC)
imaging path and a continuous wave Doppler (CWD) path. The VCA5807 is intended for prototyping and
evaluation. This user's guide includes a complete circuit description, schematic diagram, and bill of
materials (BOM).
The following related documents are available through the Texas Instruments web site at
http://www.ti.com.
Table 1. Related Document
Device
Literature Number
VCA5807
SLOS727
Contents
VCA5807 Overview ......................................................................................................... 3
1.1
Important Disclaimer Information ................................................................................ 3
2
Overview ..................................................................................................................... 3
2.1
Introduction ......................................................................................................... 3
2.2
Default Configuration .............................................................................................. 4
3
Software Installation and Operation ...................................................................................... 5
3.1
Minimum Requirements ........................................................................................... 5
3.2
Installing the Software (PC Application) ........................................................................ 5
3.3
GUI Overview ....................................................................................................... 6
4
Hardware ................................................................................................................... 11
4.1
Introduction ........................................................................................................ 11
4.2
Board Configuration .............................................................................................. 12
4.3
Power .............................................................................................................. 13
4.4
Clock Buffer ....................................................................................................... 13
4.5
VCA Inputs ........................................................................................................ 13
4.6
VCA5807 Device ................................................................................................. 13
4.7
VCA Outputs ...................................................................................................... 13
4.8
CW Mode .......................................................................................................... 14
4.9
VControl ........................................................................................................... 16
4.10 Serial Interface .................................................................................................... 16
5
Quick Start .................................................................................................................. 17
5.1
Test Setup ......................................................................................................... 17
5.2
Power Up VCA5807EVM ........................................................................................ 17
5.3
Launch the VCA5807 GUI ....................................................................................... 17
Appendix A
Bill of Materials (BOM) ........................................................................................... 18
Appendix B
PCB Layout and Schematics ................................................................................... 22
1
List of Figures
1
VCA5807EVM Basic Configuration ....................................................................................... 4
Pentium, Celeron are registered trademarks of Intel.
Windows is a registered trademark of Microsoft Corporation.
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
1
www.ti.com
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
............................................................................. 6
Hardware/Power/RST Tab of the VCA5807EVM GUI ................................................................. 7
VCA LNA+VCA+PGA+LPF Tab of the VCA5807EVM GUI ........................................................... 8
VCA CW Mode Tab ......................................................................................................... 9
VCA Debugging/Recording Tab ......................................................................................... 10
HW Setup ................................................................................................................... 11
PCB Layout With Jumper Positions ..................................................................................... 12
CW Mode Hardware Configuration...................................................................................... 14
Switching to CW Mode ................................................................................................... 15
Oscilloscope ................................................................................................................ 16
Top Layer - Signal ......................................................................................................... 22
Second Layer - Ground ................................................................................................... 23
Third Layer - Power ....................................................................................................... 24
Fourth Layer - Signal...................................................................................................... 25
Fifth Layer - Ground ....................................................................................................... 26
Bottom Layer - Signal ..................................................................................................... 27
Schematic 1 of 10 ......................................................................................................... 28
Schematic 2 of 10 ......................................................................................................... 29
Schematic 3 of 10 ......................................................................................................... 30
Schematic 4 of 10 ......................................................................................................... 31
Schematic 5 of 10 ......................................................................................................... 32
Schematic 6 of 10 ......................................................................................................... 33
Schematic 7 of 10 ......................................................................................................... 34
Schematic 8 of 10 ......................................................................................................... 35
Schematic 9 of 10 ......................................................................................................... 36
Schematic 10 of 10 ........................................................................................................ 37
Introduction Tab of the VCA5807EVM GUI
List of Tables
2
1
Related Document .......................................................................................................... 1
2
Power Table ................................................................................................................ 13
3
Bill of Materials............................................................................................................. 18
VCA5807 Development Guide
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
VCA5807 Overview
www.ti.com
1
VCA5807 Overview
1.1
Important Disclaimer Information
CAUTION
The VCA5807EVM is intended for feasibility and evaluation testing only in
laboratory and development environments. This product is not for diagnostic
use.
Use the VCA5807 only under the following conditions:
• The VCA5807EVM is intended only for electrical evaluation of the features of the VCA5807 device in a
laboratory, simulation, or development environment.
• The VCA5807EVM is not intended for direct interface with a patient, or patient diagnostics.
• The VCA5807EVM is intended only for development purposes. It is not intended to be used as all or
part of an end-equipment application.
• The VCA5807EVM should be used only by qualified engineers and technicians who are familiar with
the risks associated with handling electrical and mechanical components, systems, and subsystems.
• The user is responsible for the safety of themself, fellow employees, contractors, and coworkers when
using or handling the VCA5807EVM. Furthermore, the user is fully responsible for the contact interface
between the human body and electronics; consequently, the user is responsible for preventing
electrical hazards such as shock, electrostatic discharge, and electrical overstress of electric circuit
components.
2
Overview
2.1
Introduction
This document is intended as a step-by-step guide through the VCA5807 Evaluation Module (EVM) setup
and test. The EVM is shipped with a default configuration from the manufacturer. With this configuration,
the onboard CMOS clock is used for an analog-to-digital converter sampling clock; the onboard oscillator
is used for CW mode operation. No external clock generator is required. The input signal for measurement
from a signal generator must be provided.
A detailed explanation regarding the jumpers, connectors, and test points appears in Section 2.2. The
graphical user interface (GUI) is available from the TI Web Site. Go to the software section of the product
folder (VCA5807).
Throughout this document, the abbreviation EVM and the term evaluation module are synonymous with
the VCA5807EVM.
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
3
Overview
2.2
www.ti.com
Default Configuration
Figure 1 shows the default configuration of the EVM from the factory. The accompanying list identifies the
basic components on the EVM board.
Figure 1. VCA5807EVM Basic Configuration
1.
2.
3.
4.
5.
6.
4
P1 – Power supplies connector
JP2, and JP3 are set to enable 3.3-V and 5-V power supplies to the device
JP15: Enables onboard VCNT
P17: Disables PDB_Global
P15: Chooses the device Common Mode for the I/V Amp Common Mode
P16: Chooses Vss as –5 V for low-side power supply on I/V Amp
VCA5807 Development Guide
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Software Installation and Operation
www.ti.com
3
Software Installation and Operation
3.1
Minimum Requirements
Before installing the software, verify that your PC meets the minimum requirements outlined in this
section.
3.1.1
Required Setup for VCA5807EVM GUI Software
•
•
•
•
•
•
•
•
3.1.2
Additional Requirements for Use with Hardware
•
•
•
3.2
PC-compatible computer
Pentium® III or Celeron® processor, 866 MHz or equivalent
Minimum 256 MB of RAM (512 MB or greater recommended)
Hard disk drive with at least 200 MB free space
Windows® XP operating system with SP2, or Windows 7 operating system
1280 × 1024 or greater display screen resolution
Mouse or other pointing device
Available USB input
VCA5807EVM
USB cable
Power supply to supply ±5 V
Installing the Software (PC Application)
The GUI software to evaluate the VCA5807 device is available at the Texas Instruments web site at
www.ti.com (VCA5807).
Before installing the software, make sure the VCA5807EVM is not connected to the PC. If using a
machine with Windows 7, it is recommended to have administrator rights to avoid problems during
installation.
Unzip the installer file to a temporary directory, and then double click setup.exe from the directory. The
installation creates a program menu item to execute the software.
Windows should automatically install the correct device drivers, but if there are problems installing the
device drivers please refer to this e2e post.
http://e2e.ti.com/support/other_analog/imaging_afes/f/239/p/213841/754871.aspx#754871
Follow these directions to ensure proper installation of the PC application.
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
5
Software Installation and Operation
3.3
www.ti.com
GUI Overview
Every tab in the VCA5807EVM GUI has a software reset option available by clicking the Software Reset
button located at the bottom right of the GUI.
The VCA Introduction tab: This tab gives a block diagram of the VCA5807 device.
Figure 2. Introduction Tab of the VCA5807EVM GUI
6
VCA5807 Development Guide
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Software Installation and Operation
www.ti.com
The VCA HARDWARE/POWER/RST tab: This tab allows the execution of different power down options.
Figure 3. Hardware/Power/RST Tab of the VCA5807EVM GUI
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
7
Software Installation and Operation
www.ti.com
The VCA LNA+VCA+PGA+LPF tab: The settings of the Low Noise Amplifier (LNA), VCA, Programmable
Gain Amplifier (PGA), and the Low Pass Filter (LPF) are adjusted in this tab.
• LNA: Adjusts the gain of each channel, adjust the active termination resistors, and disable the LNA
offset Integrator
• VCA: Adjusts the digital Time Gain Control (TGC) Attenuator
• PGA: Adjusts the PGA gain, Clamp Level, and disable both the overload clamp and the offset
integrator
• LPF: Adjusts the LPF frequency
Figure 4. VCA LNA+VCA+PGA+LPF Tab of the VCA5807EVM GUI
8
VCA5807 Development Guide
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Software Installation and Operation
www.ti.com
The VCA CW Mode tab: The Continuous-wave (CW) Doppler mode is adjusted in this tab as well as the
phases of each CW channel (1-8), the CW CLK, and the feedback resistors to control the gain. CH7 and
CH8 are brought to the CW pins by using the PGA Test Mode.
Figure 5. VCA CW Mode Tab
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
9
Software Installation and Operation
www.ti.com
The VCA Debugging/Recording tab: Command executions are saved to a file in this tab. The file can be
played back at any time by clicking on the Exec CMD File button. This tab also displays the Write Status,
and the ability to see the digital waveform of the SCLK, SDATA, and SEN pins.
Figure 6. VCA Debugging/Recording Tab
10
VCA5807 Development Guide
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Hardware
www.ti.com
4
Hardware
4.1
Introduction
The following illustration shows the setup of the VCA5807EVM and external connectors. For the default
configuration as shown in Figure 1, it is unnecessary to have an external sampling clock and external
Vcntl supply. The onboard CMOS clock and onboard Vcntl are used.
Figure 7. HW Setup
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
11
Hardware
4.2
www.ti.com
Board Configuration
Power up the VCA5807EVM by applying +5 V and –5 V to the P1 connector. After power up is complete,
three green LEDs and three red LEDs (LED 41, LED42, and LED 43) are turned. Locations of LEDs are
shown in Figure 8.
Figure 8. PCB Layout With Jumper Positions
12
VCA5807 Development Guide
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Hardware
www.ti.com
4.3
Power
The power configuration of the board is shown in Figure 18, page 1 of the schematic. Refer to Table 2 for
a list of important power components.
Table 2. Power Table
4.4
Connector
Description
P1/JP6
P1 is the +5-V and –5-V power supply connector. JP6 is the test point for +5-V/-5-V
power supply.
JP3
Onboard 5-V enable. The configuration must be set up as shown in Figure 7 in order to
use onboard 5-V supply.
TP-5V
-5-V supply test point
+5VA
+5-V supply test point
JP2
Onboard 3.3-VA enable. The configuration must be set up as shown in Figure 7 in order
to use the onboard 3.3 V.
TP33VA
+3.3-VA supply test point
TP1 through TP4
Ground test points
Clock Buffer
The clock buffer drives the VCA5807 device. Each clock buffer output should only drive one VCA5807. Do
not use one clock to drive multiple VCA5807s. This is due to the fact that the clock buffer's load
capacitance increases by a factor of N, which then results in degraded falling and rising times. Select
different clock inputs in the GUI. LEDs 41 and 42 demonstrate the PLL status of the clock buffer.
4.5
VCA Inputs
J1 through J8 are the analog input signals for CH1 through CH8. Connect to a signal generator. If the
signal is too noisy, apply a bandpass filter between the generator and the SMA to get a better result. Use
TP3-TP10 to see the input signal to the board.
4.6
VCA5807 Device
The VCA5807 device is a suitable ultrasound analog front end solution for high-end systems and portable
systems. This device contains eight channels of VCA, and CW mixer. The VCA includes an LNA, Voltagecontrolled Attenuator (VCAT), PGA, and an LPF. Each of these features is adjusted via the VCA5807
EVM GUI. For a more detailed explanation of the VCA5807 device please refer to the datasheet. The
datasheet is found on the TI product folder at www.ti.com. (SLOS727)
4.7
VCA Outputs
J26 through J36 are the output signals for CH1 through CH8. All channels have a single-ended output
through an OPA842 buffer amplifier. However, CH1 has the option of a fully differential output signal
through a THS4130 amplifier. In order to use this amplifier, install R734 and R738 and remove R837,
C317, and C318. CH8 also provides an added feature by allowing the choice of the OPA830 as the buffer
amplifier. In order to use this amplifier, install R776 and R777 and remove U35.
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
13
Hardware
4.8
www.ti.com
CW Mode
Figure 9. CW Mode Hardware Configuration
14
VCA5807 Development Guide
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Hardware
www.ti.com
•
•
•
Go to the CW Mode tab on the GUI.
Check CW MODE ENABLE. LED41, LED42, and LED43 on the VCA5807EVM should all illuminate.
Select 500 Ω for the gain control feedback resistor.
Figure 10. Switching to CW Mode
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
15
Hardware
•
•
www.ti.com
Apply an analog signal (2.51 MHz, –10 dBm) to any analog input SMA.
The CW outputs (J12, J13) display the frequency I and Q signals at 10 kHz as shown in Figure 11.
The GUI Gain Control Feedback Resistor can vary the amplitude of the outputs.
Figure 11. Oscilloscope
4.9
VControl
Switch between using the onboard Vcntl or the external Vcntl by using JP15. External Vcntl can range
from 0 V to 1.5 V. If using the external Vcntl, then a DC voltage source must be connected to J14. The
default setup uses onboard Vcntl. VR2 is used to make onboard Vcntl adjustments.
4.10 Serial Interface
The serial interface of the board is located on the bottom right-hand side. USB1 is the USB interface
connector. P13 and P14 are test points for the USB data bus: From pin 1 to pin 9, the signals are D0, D4,
D2, D1, D7, D5, D6, D3, and DGND. P14 on the VCA5807EVM is not installed.
16
VCA5807 Development Guide
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Quick Start
www.ti.com
5
Quick Start
This section assumes all engineering knowledge on the device and basic overview of the VCA5807EVM.
5.1
Test Setup
Connect the EVM as shown in . Typical input signals are 5 MHz at –32 dBm. This can be applied to any
VCA input (J1-J8). If the signal is noisy, consider using a 5-MHz filter. Connect a scope or a spectrum
analyzer to the corresponding VCA output in order to measure the gain on the channel.
5.2
Power Up VCA5807EVM
Connect ±5-V power to the board. No other power connection is needed.
5.3
Launch the VCA5807 GUI
Launch the VCA5807EVM GUI. Execute a software reset with the GUI and verify the current consumption
drops from ≈0.762 A to ≈0.646 A. Enable the Active Termination Resistor of 50 Ohms (check the box) on
the LNA+VCA+PGA+LPF tab. This tab is also used to vary the gain on each channel. However, with the
default settings as shown in , the gain should be 42 dB overall. Therefore, with an input signal of 5 MHz at
–32 dBm, load resistance of 50 Ω, and an overall gain of 42 dB, the output should read ≈4 dBm or 1 Vpp.
For more details and other modes for testing and evaluating the VCA5807 device, please refer to the
previous pages of this development guide.
SLOU352 – November 2012
Submit Documentation Feedback
VCA5807 Development Guide
Copyright © 2012, Texas Instruments Incorporated
17
www.ti.com
Appendix A Bill of Materials (BOM)
This section contains Table 3, the BOM for the VCA5807EVM.
Table 3. Bill of Materials
Item
Qty
MFG
MFG Part#
REF DES
Description
Value or Function
1
41
AVX
0402YC104KAT2A
C17, C25, C26, C29, C30, C33, C37,
C40, C51, C59, C62, C64, C76, C78,
C80, C82, C84, C86, C94, C95, C96,
C97, C98, C99, C101, C103, C125,
C130, C131, C132, C133, C134,
C135, C136, C137, C138, C139,
C140, C141, C154, C155
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,16V,10
%,0.1uF
2
2
AVX
0402YC471KAT2A
C53,C60
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,16V,10
%,470pF
3
40
0402YC104KAT2A
C160,
C167,
C177,
C265,
C309,
C314,
C319,
C324,
4
2
AVX
0402YC222KAT2A
C10, C74
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,16V,10
%,2200pF
5
11
KEMET
C0402C103K3RACTU
C290, C350, C351, C352, C353,
C354, C355, C356, C357, C358,
C363
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,0.01uF,
25V,10%,X7R
6
23
KEMET
C0402C104K8PAC
C1, C68, C69, C152, C291, C333,
C334, C335, C336, C337, C338,
C339, C340, C341, C342, C343,
C344, C345, C346, C347, C360,
C361, C362
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,0.1uF,1
0V,10%,X5R
7
2
KEMET
C0402C152J5GACTU
C73, C89
CAP,SMT,0402
CAPACITOR,SMT,0402,CERAMIC,1
500pF,50V,5%,C0G/NP0
8
8
TDK
C1005X5R0J105M
C77, C79, C81, C83, C85, C87,
C104, C126
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,1.0uF,6
.3V,20%,X5R
9
2
AVX
0402ZD105KAT2A
C71, C72
CAP,SMT,0402
CAPACITOR,SMT,0402,CERAMIC,1.
0uF,10V,20%,X5R
10
8
AVX
0402YC153KAT2A
C107, C108, C109, C116, C118,
C119, C121, C123
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,15000p
F,16V,10%,X7R
11
1
AVX
04025C102KAT2A
C32
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,1000pF
,50V,10%,X7R
12
4
AVX
04025C332KAT2A
C22, C23, C24, C41
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,3300pF
,50V,10%,X7R
13
2
AVX
04025A470JAT2A
C175, C176
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,47pF,5
0V,5%,NPO
14
7
AVX
06033C104JAT2A
C5, C7, C8, C12, C15, C88, C90
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,0.
1uF,25V,5%,X7R
15
7
AVX
0603YD105KAT2A
C38, C39, C58, C63, C159, C161,
C172
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,1.
0uF,16V,10%,X5R
16
1
TAIYO YUDEN
AMK107BJ226MA-T
C9
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,2
2uF,4V,20%,X5R
17
1
AVX
06036D106MAT2A
C4
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,1
0uF,6.3V,20%,X5R
18
2
AVX
0603YD105KAT2A
C75, C129
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,1.
0uF,16V,10%,X5R
19
2
MURATA
GRM188C80G475KE19
C6, C11
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,4.
7uF,4V,10%,X6S ( TI-F )
20
3
TAIYO YUDEN
JMK107BJ106MA-T
C31, C348, C349
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,1
0uF,6.3V,20%,X5R
21
4
KEMET
C0805C332F3GACTU
C18, C19, C45, C46
CAP,SMT,0805
CAPACITOR,SMT,0805,CERAMIC,3
300pF,25V,1%,C0G(NP0)
22
6
AVX
1206YD226KAT2A
C20, C21, C35, C36, C47, C48
CAP,SMT,1206
CAPACITOR,SMT,1206,CERAMIC,2
2uF,10V,10%,X5R
23
4
VISHAY SPRAGE
293D226X9016D2TE3
C16, C34, C43, C128
CAP,SMT,7343
CAP,TAN,SMT, 22uF,16V,+/-10%,55~85C
24
4
AVX
TPSC226K016R0375
C2, C3, C70, C151
CAPACITOR,SMT,TA
NT
10%, 16V, 22uF
25
14
AMPHENOL
901-144-8
J1, J3, J5, J7, J9, J10, J12, J13, J26,
J27, J30, J32, J33, J36
CONNECTOR,SMA
SMA COAX STRAIGHT PCB
CURRENT P/N IS 901-144-8RFX
18
C162,
C170,
C178,
C267,
C310,
C315,
C320,
C325,
C163,
C171,
C179,
C294,
C311,
C316,
C321,
C364,
C165,
C173,
C180,
C295,
C312,
C317,
C322,
C365,
C166,
C174,
C246,
C308,
C313,
C318,
C323,
C366
Bill of Materials (BOM)
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Appendix A
www.ti.com
Table 3. Bill of Materials (continued)
Item
Qty
MFG
MFG Part#
REF DES
Description
Value or Function
26
12
STEWARD
HI0805R800R-00
FB1, FB6, FB7, FB8, FB9, FB10,
FB11, FB12, FB13, FB14, FB17,
FB18
FERRITE
BEAD,SMT,2P
FERRITE,SMT,0805,80
OHM@100MHz,5A
27
1
MOLEX
39357-0003
P1
HEADER, THRU, 3P
HEADER, THRU, POWER,
3P,3.5MM, EUROSTYLE
28
1
SAMTEC
TSW-104-07-G-D
JP2
HEADER,THU
HEADER,THU,8P,2X4,MALE,DUAL
ROW,100LS,100TL
29
1
PBC09SAAN
P13
HEADER,THU,9P
HEADER,THU,MALE,0.1LS,9P,1X9,3
35H,120TL
30
4
TYCO ELECTRONICS
4-103239-0x2
JP16, JP17, JP29, JP44
HEADER,THU,JUMP
ER
MALE,2PIN,.100CC MAKE FROM 4103239-0x2
31
11
TYCO ELECTRONICS
4-103239-0x3
JP3, JP6, JP15, JP52, JP53, JP56,
JP57, P15, P16, P17, P18
HEADER,THU,JUMP
ER
MAKE FROM 4-103239-0
32
3
NATIONAL SEMI
LME49990MA/NOPB
U3, U5, U7
IC,SMT,8P
ULTRA LOW DISTORTION ULTRA
LOW NOISE OPAMP
33
1
TI
THS4130CD
U42
IC,SMT,8P
HI-SPEED,LOW NOISE,FULLDIFF,1I/O AMP,SO-8
35
1
TEXAS INSTRUMENTS
CDCM7005RGZ
CLK_BUF
IC,SMT,QFN-48
3.3-V HIGH PERFORMANCE
CLOCK SYNTHESIZER AND JITTER
CLEANER
36
3
TI
ISO7240MDW
U16, U20, U21
IC,SMT,SOIC-16W
QUAD DIGITAL ISOLATORS
37
1
TI / BURR-BROWN
OPA211AID
U13
IC,SMT,SOIC-8
1.1nV/Hz NOISE LOW POWER
PRECISION OPERATIONAL
AMPLIFIER
38
1
TI
OPA2614ID
U10
IC,SMT,SOIC-8
DUAL HI GAIN BWIDTH HI OUTPUT
CURRENT OPAMP WITH CURRENT
LIMIT
39
1
BURR-BROWN / TI
REF5025AID
U2
IC,SMT,SOIC-8
LOW-NOISE VERY LOW DRIFT
PRECISION VOLTAGE
REFERENCE,2.5V
40
2
TI
THS4131ID
U15, VCON_OPAMP
IC,SMT,SOIC-8
HIGH-SPEED LOW NOISE
DIFFERENTIAL I/O AMPLIFIERS
41
1
TI
TPS79633DCQR
U1
IC,SMT,SOT223-6
ULTRALOW-NOISE HI PSRR FAST
RF 1-A LDO LINEAR
REGULATOR,3.3V
42
1
TI / BURR-BROWN
OPA830IDBV
U43
IC,SMT,SOT23-5
LOW POWER SINGLE SUPPLY
WIDEBAND OPAMP
43
8
TI / BURR-BROWN
OPA842IDBV
U35, U36, U37, U38, U39, U40, U41,
U44
IC,SMT,SOT23-5
WIDEBAND,LOW DIST,UNITY-GAIN
STABLE,VOLTAGE-FEEDBACK
OPAMP
44
1
FUTURE TECHNOLOGY
DEVICE INT.
FT245RL
U19
IC,SMT,SSOP-28
USB FIFO IC INCORPORATE
FTDICHIP-ID SECURITY DONGLE
45
3
PANASONIC
LNJ208R82RA
LED41, LED42, LED43
LED,SMT,0603
LED,SMT,0603,ULTRA BRIGHT
RED,1.92V
46
3
PANASONIC
LNJ308G8PRA
LED-5V, LED33VA, LED5V
LED,SMT,0603
LED,SMT,0603,PURE GREEN,2.03V
49
6
VENKEL
CR0402-16W-000T
R2, R5, R14, R63, R71, R93
RES,SMT,0402
RESISTOR,SMT,0402,0
OHM,1/16W,ZERO JUMPER
50
17
VISHAY
CRCW0402000Z
R821,
R826,
R831,
R836,
RES,SMT,0402
ZERO OHM
JUMPER,SMT,0402,THICK FILM,0
OHM,1/16W,5%
51
2
VISHAY
CRCW04021001F100
R50, R92
RES,SMT,0402
RESISTOR,SMT,0402,1K,1/16W,1%,
100ppm
52
1
VISHAY
CRCW04021002F100
R95
RES,SMT,0402
RESISTOR,SMT,0402,10K,1/16W,1%
,100ppm
53
2
VISHAY
CRCW04022002F100
R44, R91
RES,SMT,0402
RESISTOR,SMT,0402,20K,1/16W,1%
,100ppm
37
VISHAY
CRCW04024990F100
R80, R81, R82, R730, R731, R736,
R793, R794, R795, R796, R797,
R798, R799, R800, R801, R802,
R803, R804, R805, R806, R807,
R808, R809, R810, R811, R812,
R813, R814, R815, R816, R817,
R818, R819, R820, R852, R853,
R854
RES,SMT,0402
RES,SMT,499
OHM,1/16W,1%,100ppm
34
47
48
R822, R823, R824, R825,
R827, R828, R829, R830,
R832, R833, R834, R835,
R837
54
55
SLOU352 – November 2012
Submit Documentation Feedback
Bill of Materials (BOM)
Copyright © 2012, Texas Instruments Incorporated
19
Appendix A
www.ti.com
Table 3. Bill of Materials (continued)
Item
Qty
MFG
MFG Part#
REF DES
Description
Value or Function
56
11
VISHAY
CRCW040249R9F100
R838, R839, R840, R841, R842,
R843, R844, R845, R846, R847,
R855
RES,SMT,0402
RES,SMT,49.9
OHM,1/16W,1%,100ppm
57
1
VISHAY
CRCW04025110F100
R58
RES,SMT,0402
RESISTOR,SMT,0402,511
OHM,1/16W,1%,100ppm
58
1
PANASONIC
ERJ-2GE0R00X
R56
RES,SMT,0402
RESISTOR/JUMPER,SMT,0402,0
OHM,5%,1/16W
59
5
PANASONIC
ERJ-2GEJ131
R28, R29, R30, R32, R43
RES,SMT,0402
RESISTOR,SMT,0402,THICK
FILM,5%,1/16W,130
4
PANASONIC
ERJ-2GEJ391
R51, R52, R54, R55
RES,SMT,0402
RESISTOR,SMT,0402,THICK
FILM,5%,1/16W,390
63
5
PANASONIC
ERJ-2GEJ820
R23, R24, R26, R27, R34
RES,SMT,0402
RESISTOR,SMT,0402,THICK
FILM,5%,1/16W,82
64
5
PANASONIC
ERJ-2RKF1000X
R25, R40, R42, R76, R78
RES,SMT,0402
RESISTOR,SMT,0402,100
OHM,1%,1/10W
65
2
PANASONIC
ERJ-2RKF2001X
R850, R851
RES,SMT,0402
RESISTOR,SMT,0402,2.00K,1%,1/16
W
66
1
PANASONIC
ERJ-2RKF3320X
R59
RES,SMT,0402
RESISTOR,SMT,0402,332
OHM,1%,1/16W
67
2
PANASONIC
ERJ-2RKF4020X
R848, R849
RES,SMT,0402
RESISTOR,SMT,0402,402
OHM,1%,1/16W
68
1
PANASONIC
ERJ-2RKF49R9X
R96
RES,SMT,0402
RESISTOR,SMT,0402,49.9
OHM,1%,1/16W
71
2
VISHAY/DALE
CRCW0603200RFKEA
R53, R57
RES,SMT,0603
RESISTOR,SMT,0603,1%,1/10W,200
OHM
73
1
PANASONIC
ERJ-3GSYJ153
R60
RES,SMT,0603
RESISTOR,SMT,0603,5%,1/10W,15K
74
2
VISHAY
TNPW0603475RBEEA
R3, R12
RES,SMT,0603
RESISTOR,SMT,0603,THIN
FILM,475 OHM 0.1%,1/10W,25ppm
75
8
VISHAY
TNPW0603499RBEEA
R18, R19, R38, R39, R46, R47, R48,
R49
RES,SMT,0603
RESISTOR,SMT,0603,THIN
FILM,499 OHM 0.1%,1/10W,25ppm
76
3
VISHAY
TNPW060349R9BEEA
R9, R36, R37
RES,SMT,0603
RESISTOR,SMT,0603,THIN
FILM,49.9 OHM,0.1%,1/10W
77
1
KYCON
STX-3000
JX1
STEREO PHONE
JACK,THU,3 PIN
STEREO PHONE JACK,THU,3
PIN,3.5mm
78
3
KEYSTONE ELECTRONICS
5000
TP2, TP33VA, TP5V
TESTPOINT,THU,1P
TESTPOINT,THU,MINIATURE,0.1LS,
120TL, RED
79
4
KEYSTONE ELECTRONICS
5001
GND1, GND2, GND3, GND4
TESTPOINT,THU,1P
TESTPOINT,THU,MINIATURE,0.1LS,
120TL, BLACK
80
2
KEYSTONE ELECTRONICS
5002
TP1, TP-5V
TESTPOINT,THU,1P
TESTPOINT,THU,MINIATURE,0.1LS,
120TL, WHITE
81
9
KEYSTONE ELECTRONICS
5004
TP3, TP4, TP5, TP6, TP7, TP8, TP9,
TP10, TP16
TESTPOINT,THU,1P
TESTPOINT,THU,MINIATURE,0.1LS,
120TL, YELLOW
83
2
MINI-CIRCUITS
ADT4-1WT
T1, T2
TRANSF,SMT,6P
RF TRANSFORMER WIDEBAND, 2775 MHz, 50 OHM
84
2
BOURNS
3296W-1-103
VR2, VR3
TRIMPOT,THU,3P
TRIMPOT,THU,10K,10%,0.5W,100pp
m,25T
85
1
BOURNS
3296W-1-205
VR1
TRIMPOT,THU,3P
TRIMPOT,THU,2M,10%,0.5W,100pp
m,25T
86
2
PANASONIC
ERA-2AEB152X
R10, R64
RES,SMT,0402
RESISTOR,SMT,0402,THIN FILM,1.5
K,0.1%,1/16W,10ppm, Tolerance
important
87
2
PANASONIC
ERA-2AEB202X
R61, R74
RES,SMT,0402
RESISTOR,SMT,0402,THIN FILM,2
K,0.1%,1/16W,10ppm, Tolerance
important
88
8
PANASONIC
ERJ-2GEJ49R9(UN)
R65, R66, R67, R68, R69, R70, R77,
R79
RES,SMT,0402
( UNINSTALLED PART )
89
4
PANASONIC
ERJ-3GSYJ102(UN)
R20, R21, R22, R41
UNINSTALLED
( UNINSTALLED PART )
90
12
UNINSTALLED
CRCW04020000Z0ED(UN)
R1, R6, R7, R8, R11, R15, R16, R17,
R62, R72, R73, R75
UNINSTALLED
UNINSTALLED
91
1
PBC09SAAN
P14
UNINSTALLED
HEADER,THU,MALE,0.1LS,9P,1X9,3
35H,120TL
60
61
62
82
92
93
4
AVX
0402YC104KAT2A(UN)
C27, C28,C100, C102
UNINSTALLED
UNINSTALLED
94
2
TAIYO YUDEN
LMK105BJ104KV- F
C42, C44
CAP,SMT,0402
CAPACITOR,SMT,0402,CERAMIC,1
0V,Y5V,0.1uF,20%
20
Bill of Materials (BOM)
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Appendix A
www.ti.com
Table 3. Bill of Materials (continued)
Item
Qty
MFG
MFG Part#
REF DES
Description
Value or Function
95
2
KEMET
C0402C152J5GACTU
C13, C14
CAP,SMT,0402
CAPACITOR,SMT,0402,CERAMIC,1
500pF,50V,5%,C0G/NP0
96
2
SUSUMU
RG1005N202B
R4, R13
UNINSTALLED
RESISTOR,SMT,0402,THIN FILM,2
K,0.1%,1/16W,10ppm,(UNINSTALLE
D)
97
1
PANASONIC
ERJ-2GEJ820
R33
RES,SMT,0402
RESISTOR,SMT,0402,THICK
FILM,5%,1/16W,82 (UNINSTALLED)
98
1
PANASONIC
ERJ-2GEJ131
R31
RES,SMT,0402
RESISTOR,SMT,0402,THICK
FILM,5%,1/16W,130
(UNINSTALLED)
99
1
PANASONIC
ERJ-2GEJ161
R35
RES,SMT,0402
RESISTOR,SMT,0402,THICK
FILM,5%,1/16W,160
(UNINSTALLED)
100
3
TI
LMH6629SDE/NOPB
U4, U6, U8
IC,SMT,DFN-8
ULTRA-LOW NOISE,PRECISION
OPERATIONAL AMPLIFIERS
101
8
PANASONIC
ECJ-0EC1H470J
C332, C329, C330, C331, C326,
C327, C328, C359
CAP,SMT,0402
CAPACITOR,SMT,0402,CER,47pF,5
0V,5%,NPO
102
2
AVX
06033C104JAT2A
C91, C92
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,0.
1uF,25V,5%,X7R
103
1
PANASONIC
ECJ-1VB1C105K
C93
CAP,SMT,0603
CAPACITOR,SMT,0603,CERAMIC,1.
0uF,16V,10%,X5R
104
1
VISHAY
CRCW04024701F100
R45
RES,SMT,0402
RESISTOR,SMT,0402,4.7K,1/16W,1
%,100ppm
105
1
TYCO ELECTRONICS
4-103239-0x3
P18
UNINSTALLED
MAKE FROM 4-103239-0, DNI
106
4
Vishay
CRCW04020000Z0ED(UN)
R734, R738, R776, R777
UNINSTALLED
VISHAY_0402_1x0.5x0.35mm_016H
107
16
COMPONENTS CORP
TP105-01-04
TP34, TP35, TP36, TP37, TP38,
TP39, TP40, TP41, TP42, TP43,
TP44, TP45, TP46, TP47, TP48,
TP49
UNINSTALLED
TEST POINTS,THU,SMALL,TL-70,
YELLOW, DNI
108
1
ADVANCED CONNECTEK
MNE20-5K5P10
USB1
CONN,SMT,5P
MINI-AB USB OTG RECEPTACLE
R/A SMT TYPE, Use 670-1523-1-ND
instead.
109
11
EFJOHNSON
142-0721-891
J2, J4, J6, J8, J14, J17, J28, J29,
J31, J34, J35
CONN,THU,SMA
JACK
SMA JACK END LAUNCH, 0.080
PCB THICK, Use J630-ND for board
thickness of .042 or J502-ND for
.062 or J992-ND for .068
110
1
CONNOR WINFIELD
CWX813-10.0M
X1
OSC,SMT,4P
OSCILLATOR,SMT,4P,3.3V,+/25ppm,-20~70C,10.000 MHz, Use
FVXO-PC73B-640-ND instead
111
1
VCA5807PZP
DUT1
Customer Supplied
"IC, Fully Integrated, 8-Channel
Voltage Controlled Amplifier for
Ultrasound with Passive CW Mixer,
0.75 nV/rtHz, 99 mW/CH "
112
1
OSC,SMT,6P
VX-7040-ECE-KXX-0640M000
OSC1
OSC,SMT,6P
VCXO,SMT,3.3V,40Mhz
5.0x7.5x1.8mm ( Customer Supply )
113
15
Molex
15-29-1025
SHUNT-JUMPER
CONN SHUNT CLOSED TOP .100
GOLD
Special Instructions and Notes:
1. Include extra Shunt-Jumpers with board.
* Alternative Part suggested
* Orange=Tolerance is significant
Note: Asterisk(*) next to part manufacturer's name denotes possible long lead time item.
* Green= Exact part, No Substitutions
* Blue= Uninstalled
* Yellow= TI Provided part
SLOU352 – November 2012
Submit Documentation Feedback
Bill of Materials (BOM)
Copyright © 2012, Texas Instruments Incorporated
21
www.ti.com
Appendix B PCB Layout and Schematics
B.1
PCB Layout
Figure 12 through Figure 17 show the PCB layouts for this EVM.
Figure 12. Top Layer - Signal
22
PCB Layout and Schematics
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
PCB Layout
www.ti.com
Figure 13. Second Layer - Ground
SLOU352 – November 2012
Submit Documentation Feedback
PCB Layout and Schematics
Copyright © 2012, Texas Instruments Incorporated
23
PCB Layout
www.ti.com
Figure 14. Third Layer - Power
24
PCB Layout and Schematics
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
PCB Layout
www.ti.com
Figure 15. Fourth Layer - Signal
SLOU352 – November 2012
Submit Documentation Feedback
PCB Layout and Schematics
Copyright © 2012, Texas Instruments Incorporated
25
PCB Layout
www.ti.com
Figure 16. Fifth Layer - Ground
26
PCB Layout and Schematics
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
PCB Layout
www.ti.com
Figure 17. Bottom Layer - Signal
SLOU352 – November 2012
Submit Documentation Feedback
PCB Layout and Schematics
Copyright © 2012, Texas Instruments Incorporated
27
Schematics
B.2
www.ti.com
Schematics
Figure 18 through Figure 27 show the schematics for this EVM in landscape mode, for readability.
JP2
FB6
TP33VA
U1
FB7
FB1
FB8
LED33VA
R59
LED5V
R40
C1
C2
C3
JP6
FB9
C68
TP5V
U2
TP-5V
FB12
R58
JP3
FB11
TP1
C4
LED-5V
FB13
C151
C152
TP2
P1
FB10
C70
C69
GND1
GND2
GND3
GND4
Figure 18. Schematic 1 of 10
28
PCB Layout and Schematics
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Schematics
www.ti.com
C31
C32
R32
C33
OSC1
R31
R33
X1
R34
C94
R29
R28
R35
R27
R26
CLK_BUF
R44
R30
R43
R45
C42
C44
C43
R80
LED43
R24
R23
CLK_BUF
LED41
C98
C128
C129
C131
C96
C95
C133
C138
C137
C136 C135
R81
C34
C93
C130
LED42
R82
C99
C134
C139
C140
C97
C16
C75
C132
Figure 19. Schematic 2 of 10
SLOU352 – November 2012
Submit Documentation Feedback
PCB Layout and Schematics
Copyright © 2012, Texas Instruments Incorporated
29
Schematics
www.ti.com
TP10
C103
J1
R77
C104
TP6
C107
C76
J2
R65
C77
C108
TP9
C78
J3
R66
C109
C79
C118
TP5
C80
J4
R67
C116
C81
C119
TP8
C82
J5
C121
R68
C83
C123
TP4
C84
J6
R69
C85
TP7
C86
J7
R70
C87
TP3
C125
J8
R79
C126
Figure 20. Schematic 3 of 10
30
PCB Layout and Schematics
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Schematics
www.ti.com
TP34 TP36
TP35 TP37
R821
R822
R823
R824
TP38 TP40
TP39 TP41
R825
R826
DUT1
R827
R828
TP42 TP44
TP43 TP45
R829
C349
C348
R830
R831
R832
R836
R835
R834
R833
TP46 TP48
TP47 TP49
C294
C295
C365
C366 C310
C308
C309
Figure 21. Schematic 4 of 10
SLOU352 – November 2012
Submit Documentation Feedback
PCB Layout and Schematics
Copyright © 2012, Texas Instruments Incorporated
31
Schematics
www.ti.com
R809
R797
C361
C317
C342
C313
R810
C363
C332
C318
C350
R730
R839
C329
J34
R731
R734
R798
R838
J28
R818
U39
U44
C362
C314
C343
R817
R799
R738
C346
R795
R851
C321
C319
C340
C315
R800
C351
C335
C325
R848
R849
U42
R796
C356
C357
R846
R841
J29
R816
R840
C330
J36
R806
J33
U38
C331
C316
R815
C347
U41
C358
C324
R847
C341
R805
J27
C320
R853
R811
R837
C291
C339
C333
C267
C323
R850
U36
C246
J35
C265
R736
C360
C334
R802
C352
C326
R807
R855
R852
J31
R808
C322
U35
C359
R843
C327
C344
C364
C290
C353
R801
R854
R812
R842
J30
R814
R793
R803
R813
R776
U37
C345
R777
C336
C337
C311
R804
C355
C354
U43
R844
C328
R845
J26
J32
R820
U40
C312
R819
C338
R794
Figure 22. Schematic 5 of 10
32
PCB Layout and Schematics
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Schematics
www.ti.com
C28
C17
T1
J9
C101
C100
R76
R25
C30
C29
C102
C51
C27
T2
J10
C141
R42
R78
C25
C26
Figure 23. Schematic 6 of 10
SLOU352 – November 2012
Submit Documentation Feedback
PCB Layout and Schematics
Copyright © 2012, Texas Instruments Incorporated
33
Schematics
www.ti.com
C58
J14
C59
R96
R51
JP15
R52
R53
U13
R95
C172
C63
C53
VR2
JP16
C64
C171
C62
C161
VCON_OPAMP
R57
C162
R91
R93
R55
R54
C60
JP17
VR1
R56
JP29
C174
C173
C159
C160
C163
C170
Figure 24. Schematic 7 of 10
34
PCB Layout and Schematics
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Schematics
www.ti.com
JP52
C19
R39
R19
C21
U10
C22
C35
R36
R20
J12
C20
R38
R18
JP53
C18
C23
R21
C39
JX1
C40
U10
C38
JP56
C37
C41
R49
C46
R41
J13
R48
C47
U10
R37
C36
C48
JP57
C24
R22
R47
R46
C45
Figure 25. Schematic 8 of 10
SLOU352 – November 2012
Submit Documentation Feedback
PCB Layout and Schematics
Copyright © 2012, Texas Instruments Incorporated
35
Schematics
www.ti.com
C155
FB17
Serial Interface
P13
U16
C154
P17
JP44
R50
C180
C167
U21
C179
R92
U20
FB18
C166
P18
P14
TP16
USB1
U19
C178
C177
FB14
C165
There are two ground planes here.
We isolate the USB circuit from
the rest of the board. The circuits are only
coupled through the opto-isolators.
C175
USB1
C176
Figure 26. Schematic 9 of 10
36
PCB Layout and Schematics
SLOU352 – November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Schematics
www.ti.com
P15
C89
C72
C11
R12
R74
R60
C12
VR3
C71
C74
C9
R9
R16
U8
P16
J17
R64
U7
C14
C92
U8
R13
R17
R15
R71
R72
R14
C15
C88
R73
U6
U15
R62
U5
C90
R10
R11
C6
C73
C13
R3
R63
R75
U6
C10
C91
R2
R1
R4
R61
C5
ALL Bypass Caps in
this circuit need to be
tied close to the pin.
C7
U4
R7
U3
Differential could fit between the
single-ended amps in the layout.
R6
R5
R8
U4
C8
This Circuit provides 3
options for populating
Op-Amps for maximum flexibility
Figure 27. Schematic 10 of 10
SLOU352 – November 2012
Submit Documentation Feedback
PCB Layout and Schematics
Copyright © 2012, Texas Instruments Incorporated
37
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising