Texas Instruments | LM4930 Audio Subsystem w/Stereo Headphone - Mono Speaker Amps (Rev. C) | Datasheet | Texas Instruments LM4930 Audio Subsystem w/Stereo Headphone - Mono Speaker Amps (Rev. C) Datasheet

Texas Instruments LM4930 Audio Subsystem w/Stereo Headphone - Mono Speaker Amps (Rev. C) Datasheet
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
LM4930 Boomer™ Audio Power Amplifier Series Audio Subsystem with Stereo
Headphone & Mono Speaker Amplifiers
Check for Samples: LM4930
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
The LM4930 is an integrated audio subsystem that
supports voice and digital audio functions. The
LM4930 includes a high quality I2S input stereo DAC,
a voice band codec, a stereo headphone amplifier
and a high-power mono speaker amplifier. It is
primarily designed for demanding applications in
mobile phones and other portable devices.
1
23
•
•
•
•
16-bit Resolution 48kHz Stereo DAC
16-bit Resolution 8kHz Voice Codec
I2S Digital Audio Data Serial Interface
Two-wire Serial Control Interface
PCM Voice Audio Data Serial Interface
25mW/channel Stereo Headphone Amplifier
330mW Mono 8Ω Amplifier (at AVDD = 3.0V)
32-step Volume Control for Audio Output
Amplifiers
No Snubber Networks or Bootstrap Capacitors
are Required by the Headphone or Hands-free
Amplifiers
Digital Sidetone Generation with Adjustable
Attenuation
Gain Controllable Headphone Amp, Mono BTL
Amp, Mic Preamp
Available in the 36–bump DSBGA and 44–lead
WQFN Packages
APPLICATIONS
•
•
•
Mobile Phones
Mobile/low Power Audio Appliances
PDAs
The LM4930 features an I2S serial interface for full
range audio, a 16-bit PCM bi-directional serial
interface for the voice band codec and an two-wire
interface for control. The full range music path
features an SNR of 86dB with a 16-bit 48kHz input.
The stereo DAC can also be used while the voice
codec is in use. The headphone amplifier delivers
25mWRMS to a 32Ω single-ended stereo load with
less than 0.5% distortion (THD+N) when AVDD = 3V.
The mono speaker amplifier delivers up to 330mW
into an 8Ω load with less than 1% distortion when
AVDD = 3V.
The LM4930 employs advanced techniques to reduce
power consumption, to reduce controller overhead
and to eliminate click and pop. Boomer audio power
amplifiers were designed specifically to provide high
quality output power with a minimal amount of
external components. It is, therefore, ideally suited for
mobile phone and other low voltage applications
where minimal power consumption is a primary
requirement.
KEY SPECIFICATIONS
•
•
•
•
•
•
(1)
PLS OUT at AVDD = 5.0V, 8Ω 1% THD+N 1W
(typ)
PLS OUT at AVDD = 3.0V, 8Ω 1% THD+N
330mW (typ)
PH/P OUT at AVDD = 3.0V, 32Ω 0.5% THD+N
25mW (typ)
Supply Voltage Range
– DVDD (1) 2.6V to 4.5V
– AVDD (1) 2.6V to 5.5V
Total Shutdown Current 2μA (typ)
PSRR at 217Hz, AVDD = 3V 50dB (typ)
Best operation is achieved by maintaining 3.0V ≤ AVDD ≤ 5.0
and 3.0V ≤ DVDD ≤ 3.6V. AVDD must be equal to or greater
than DVDD. for proper operation.
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Boomer is a trademark of Texas Instruments Incorporated.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2013, Texas Instruments Incorporated
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Typical Application
IRQ
SDA
SCL
DAC_REF
Click and pop
suppression and
power up circuits
CTRL
REFERENCE
CIRCUIT
BYPASS CAP
MIC_REF
MIC BIAS
ADDR
XTAL _ IN
HP SENSE IN
XTAL
OSC
1M
XTAL _ OUT
22 pF
22 pF
Power Management and Control
PCMSYNC
PCMCLK
PCMSDI
ADC
PCM
8 kHz
InOut
PCMSDO
LS+
DAC
AB
I2SWS
48 kHz
Input
Speaker
LS-
16
16
I2SCLK
Microphone
MICLPF
+
HPL
MIXER
STEREO
I2S
I2SSDI
HP SENSE OUT
MIC+
16
AB
LPF
16
DAC
Headphones
2 x 25 mW
AB
HPR
Figure 1. Typical I2S + Voice Codec Application Circuit for Mobile Phones
Connection Diagrams
Figure 2. 36 - Bump DSBGA Package
See Package Number YZR0036KRA
2
40
39
38
PCM_SDI
DGND_X
41
PCM_SDO
I2S_DATA
42
PCM_CLK
I2S_CLK
43
I2S_WS
44
DVDD_X
IRQ
Top View
NC
Top View
37
36
35
31
SDA
HPSENSE_IN
5
30
ADDR
HPSENSE_OUT
6
29
BYPASS
AVDD_MIC
7
28
DAC_REF
AVDD_HP
8
27
AVDD_LS
LS+
9
26
MIC_REF
LS+
10
25
MIC_P
LS-
11
24
MIC_N
LS-
12
23
MIC_BIAS
13
14
15
16
17
18
19
20
21
22
AGND_LS
4
NC
SCL
DGND_D
NC
32
NC
3
HP_L
PCM_SYNC
XTAL_OUT
AVDD_LS
33
HP_R
NC
2
AGND_LS
34
MCLK/XTAL_IN
AGND_HP
1
A_MICGND
DVDD_D
Figure 3. 44 - Lead WQFN Package
See Package Number NJN0044A
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Pin Descriptions
Pin No.
Pin Name
Description
A1
MIC_P
Microphone positive differential input
A2
MIC_N
Microphone negative differential input
A3
AVDD_MIC
Analog Vdd for microphone preamp
A4
DAC_REF
D/A converter reference voltage
A5
SDA
Two-wire control interface serial data pin
A6
SCL
Two-wire control interface serial clock pin
B1
AGND_MIC
Analog ground for microphone preamp
B2
MIC_BIAS
Microphone bias supply output (2V)
B3
MIC_REF
Internal fixed-reference bypass capacitor decoupling pin
B4
ADDR
Control bus address select pin
B5
PCM_SDI
PCM serial data in
B6
PCM_CLK
PCM Serial clock pin
C1
AVDD_HP
Analog Vdd for headphone amplifier
C2
NC
No Connect
C3
BYPASS
Half-supply bypass capacitor decoupling pin
C4
PCM_SYNC
PCM Frame sync pin
C5
I2S_DATA
I2S serial data input
C6
DGND_D
Digital ground
D1
HP_L
Headphone amplifier connection (Left)
D2
HP_R
Headphone amplifier connection (Right)
D3
HPSENSE_IN
Connection for sense pin of headphone jack
D4
PCM_SDO
PCM serial data out
D5
I2S_CLK
I2S serial bit clock
D6
DVDD_D
Digital Vdd
E1
AGND_HP
Analog ground for headphone amplifier
E2
LS-
Loudspeaker amplifier BTL negative out (-)
E3
HPSENSE_OUT
Logic output pin to indicate headphone connection status. Outputs logic high when HPSENSE_IN is
high and outputs logic low when HPSENSE_IN is low. See Figure 50 for suggested application circuit
E4
IRQ
LM4930 mode status indicator pin
E5
I2S_WS
I2S word select
E6
XTAL_OUT
Negative feedback source for external crystal MCLK
F1
AGND_LS
Analog ground for loudspeaker amplifier
F2
LS+
Loudspeaker amplifier BTL positive out (+)
F3
AVDD_LS
Analog VDD for loudspeaker amplifier
F4
DGND_X
Digital ground
F5
DVDD_X
Digital VDD
F6
MCLK/XTAL_IN
12.288MHz or 24.576MHz Master Clock from crystal (via XTAL OUT) or external source
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
3
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
System Control Registers
The LM4930 is controlled with a two-wire serial interface. This interface is used to configure the operating mode,
digital interfaces, and delta-sigma modulators. The LM4930 is controlled by writing information into a series of
write-only registers, each with its own unique 7 bit address. The following registers are programmable:
Table 1. BASIC CONFIGURATION Registers (1)
BASIC CONFIGURATION (XX1000). (Set = logic 1, Clear = logic 0)
BIT
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address
Register
Description
3:0
MODE
The LM4930 can be placed in one of several modes that dictate the basic operation. When a new
mode is selected the LM4930 will change operation silently and will re-configure the power
management profile automatically. The modes are described as follows: (2)
Mode
Mono Speaker
Amplifier Source
Headphone Left
Source
Headphone Right
Source
Comment
0000
None
None
None
Powerdown mode
0001
None
None
None
Standby mode
0010
Voice
None
None
Mono speaker
mode
0011
None
Voice
Voice
Headphone call
mode
0100
Voice
Voice
Voice
Conference call
mode
0101
Audio (L+R)
None
None
L+R mixed to mono
speaker
0110
None
Audio (Left)
Audio (Right)
Headphone stereo
audio
0111
Audio (L+R)
Audio (Left)
Audio (Right)
L+R mixed to mono
speaker + stereo
headphone audio
1000
Audio (Left)
Voice
Voice
Mixed Mode
1001
Voice + Audio (Left) Voice
Voice
Mixed mode
1010
Voice
Audio (Left)
Mixed Mode
Audio (Left)
4
SOFT_RESET
Resets the LM4930, excluding the control registers
5
PCM_LONG
If set the PCM interface uses a long frame sync. (3)
6
PCM_COMPANDED
If set the 8 MSBs are presumed to be companded data and the 8 LSBs are ignored. (3)
7
PCM_LAW
If set, the companded G711 data is set to be A-law, else µ-law is assumed (3)
8:9
PCM_SYNC_MODE
Sets 1 (00h), 2 (01h) or 4(10h) 16 bit frames per sync. The PCM_SDO pin is tri-stated during the
latter frames. (3)
10
PCM_ALWAYS_ON
This bit should be set if another codec is using the PCM bus. When set, the LM4930 will drive the
clock and sync signals in all modes except Powerdown (3)
11
I2S_M/S
I2S master or slave select. If set then I2S = master. Cleared = slave
12
I2S_RES
I2S resolution select. If set then 32 bits per frame. If cleared then 16 bits per frame
13
RSVD
RESERVED (4)
14
RSVD
RESERVED (4)
15
RSVD
RESERVED (4)
(1)
(2)
(3)
(4)
4
This register is used to configure the I2S and PCM interfaces as well as the 48kHz DAC module. The 7 bit address for the
BASICCONFIG register is XX10000.
(X = 0 if ADDR is set to logic 0)
(X = 1 if ADDR is set to logic 1)
With the exception of Standby Mode, rapid switching between modes should be avoided. Rapid switching between modes will not
ensure that the desired mode will be activated.
It is recommended to alter this bit only while the part is in Powerdown Mode.
Reserved bits should be set to zero when programming the associated register.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Table 2. VOICE/TEST CONFIG Registers (1)
VOICETESTCONFIG (XX10001). (Set = logic 1, Clear = logic 0)
BIT
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address
Register
Description
0
CLASS
If set, configures the chip for use with an external class D or linear amplifier and turns the BTL
speaker output into a buffer. (2)
4:1
SIDESTONE_ATTEN
Programs the attenuation of the digital sidetone. Attenuation is set as follows:
4:1
Sidetone
Attenuation
4:1
Sidetone Attenuation
0000
Mute
1000
-9dB
0001
-30dB
1001
-6dB
0010
-27dB
1010
-3dB
0011
-24dB
1011
0dB
0100
-21dB
1100
Mute
0101
-18dB
1101
Mute
0110
-15dB
1110
Mute
0111
-12dB
1111
Mute
5
AUTOSIDE
This feature is included for use with the mono speaker in hands-free applications where sidetones
may not be desirable. If set, the sidetone is always muted in modes when voice is played on the
mono speaker (0010, 0100, 1001, and 1010), otherwise the sidetone is present at whatever level is
set in the attenuation conrol register
6
CLOCK_DIV
If set, allows for the use of a 24.576MHz crystal. Default setting is for 12.288MHz crystal. (2)
7
ZXD_DISABLE
Disables the zero crossing detect in the stereo DAC to ensure immediate mode changes rather than
waiting for a zero cross. (3)
8:9
RSVD
RESERVED (4)
10:11
CAP_SIZE
Set to accomodate different bypass capacitor values to give correct turn-off delay and click/pop
performance. Value is set as follows: (2)
10:11
Delay
Bypass Capacitor Size
00
25ms
0.1µF
01
50ms
0.39µF
10
85ms
1µF
11
RESERVED
RESERVED
12
ZXDS_SLOW
If set, this forces the stereo DAC outputs to wait for a zero crossing before powering down
13
MUTE_LS
If set, mutes the loudspeaker amplifier in any mode where it is not already muted
14
MUTE_HP
If set, mutes the headphone amplifier in any mode where it is not already muted
15
MUTE_MIC
If set, mutes the microphone preamp
(1)
(2)
(3)
(4)
This register configures the voiceband codec, sidetone attenuation, and selected control functions. The 7 bit address for the VOICE
TESTCONFIG register is XX10001.
(X = 0 if ADDR is set to logic 0)
(X = 1 if ADDR is set to logic 1)
It is recommended to alter this bit only while the part is in Powerdown Mode.
To ensure a successful transistion into Powerdown Mode, ZXD_DISABLE must be set whenever there is no audio input signal present.
Reserved bits should be set to zero when programming the associated register.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
5
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Table 3. GAIN CONFIG Registers (1)
GAINCONFIG (XX10010). (Set = logic 1, Clear = logic 0)
BIT
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address
Register
Description
4:0
LOUDSPKR_GAIN
Programs the gain of the loudspeaker amplifier. Gain is set as follows:
9:5
HP_GAIN
13:10
(1)
6
MIC_GAIN
4:0
Loudspeaker Gain 4:0
Loudspeaker Gain
00000
-34.5dB
10000
-10.5dB
00001
-33dB
10001
-9dB
00010
-31.5dB
10010
-7.5dB
00011
-30dB
10011
-6dB
00100
-28.5dB
10100
-4.5dB
00101
-27dB
10101
-3dB
00110
-25.5dB
10110
-1.5dB
00111
-24dB
10111
0dB
01000
-22.5dB
11000
1.5dB
01001
-21dB
11001
3dB
01010
-19.5dB
11010
4.5dB
01011
-18dB
11011
6dB
01100
-16.5dB
11100
7.5dB
01101
-15dB
11101
9dB
01110
-13.5dB
11110
10.5dB
01111
-12dB
11111
12dB
Programs the gain of the headphone amplifier. Gain is set as follows:
9:5
Headphone Gain
9:5
Headphone Gain
00000
-46dB
10000
-22.5dB
00001
-45dB
10001
-21dB
00010
-43.5dB
10010
-19.5dB
00011
-42db
10011
-18dB
00100
-40.5dB
10100
-16.5dB
00101
-39dB
10101
-15dB
00110
-37.5dB
10110
-13.5dB
00111
-36dB
10111
-12dB
01000
-34.5dB
11000
-10.5dB
01001
-33dB
11001
-9dB
01010
-31.5dB
11010
-7.5dB
01011
-30dB
11011
-6dB
01100
-28.5dB
11100
-4.5dB
01101
-27dB
11101
-3dB
01110
-25.5dB
11110
-1.5dB
01111
-24dB
11111
0dB
Programs the gain of the microphone amplifier. Gain is set as follows:
This register is used to control the gain of the headphone amplifier, the loudspeaker amplifier, and the microphone preamplifier. The 7
bit address for the GAINCONFIG register is XX10010.
(X = 0 if ADDR is set to logic 0)
(X = 1 if ADDR is set to logic 1)
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Table 3. GAIN CONFIG Registers(1) (continued)
15:14
(2)
RSVD
13:10
Mic Preamp Gain
0000
17dB
0001
19dB
0010
21dB
0011
23dB
0100
25dB
0101
27dB
0110
29dB
0111
31dB
1000
33dB
1001
35dB
1010
37dB
1011
39dB
1100
41dB
1101
43dB
1110
45dB
1111
47dB
RESERVED (2)
Reserved bits should be set to zero when programming the associated register.
Timing Diagrams
Figure 4. Two-Wire Control Interface Timing Diagram
Figure 5. PCM Receive Timing Diagram
Figure 6. I2S Transmit Timing Diagram
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
7
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2) (3)
Analog Supply Voltage
6.0V
Digital Storage Supply Voltage
6.0V
Storage temperature
-65°C to +150°C
Power Dissipation (4)
ESD Susceptibility
Internally Limited
Human Body Model (5)
Machine Model (6)
Junction temperature
Thermal Resistance
(1)
(2)
(3)
(4)
(5)
(6)
(7)
2000V
200V
150°C
θJA - YZR0036KRA
105°C/W
θJA - NJN0044A (7)
27°C/W
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which specifies specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
All voltages are measured with respect to the relevant GND pin unless otherwise specified.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX ,θJA, and the ambient temperature,
TA. The maximum allowable power dissipation is PDMAX = (TJMAX – TA) / θJA or the number given in Absolute Maximum Ratings,
whichever is lower. For the LM4930, see power derating currents for more information.
Human body model: 100pF discharged through a 1.5kΩ resistor.
Machine model: 220pF - 240pF discharged through all pins.
The given θA is for an LM4930 packaged in an NJN0044A with the Exposed-DAP soldered to an exposed 2in2 area of 1oz printed circuit
board copper with 16 thermal vias as described in AN-1187.
Operating Ratings (1)
Temperature Range
TMIN ≤ TA ≤ TMAX
Supply Voltage
DVDD (2)
2.6V - 4.5V
(2)
2.6V - 5.5V
AVDD
(1)
(2)
8
−30°C ≤ TA ≤ +85°C
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX ,θJA, and the ambient temperature,
TA. The maximum allowable power dissipation is PDMAX = (TJMAX – TA) / θJA or the number given in Absolute Maximum Ratings,
whichever is lower. For the LM4930, see power derating currents for more information.
Best operation is achieved by maintaining 3.0V ≤ AVDD ≤ 5.0 and 3.0V ≤ DVDD ≤ 3.6V. AVDD must be equal to or greater than DVDD. for
proper operation.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Electrical Characteristics DVDD = 3.3V, AVDD = 5V, RLHP = 32Ω, RLHF = 8Ω (1) (2) (3)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA= 25°C.
Parameter
Test Conditions
LM4930
Typ
(4)
Limits (5) (6)
Units
(Limits)
8
mA (max)
fMCLK = 12.288MHz
DIDD
Digital Power Supply Current
Output Mode = "0010"
Output Mode = "0011"
Output Mode = "0100"
2
Output Mode = "0101"
Output Mode = "0110"
Output Mode = "0111"
4.4
Output Mode = "1000"
Output Mode = "1001"
Output Mode = "1010"
4.9
fMCLK = 12.288MHz; No Load
AIDD
Analog Power Supply Quiescent
Current
Output Mode = "0010"
7.0
Output Mode = "0011"
6.3
Output Mode = "0100"
8.0
Output Mode = "0101"
8.2
Output Mode = "0110"
7.4
Output Mode = "0111"
8.7
Output Mode = "1000"
Output Mode = "1001"
Output Mode = "1010"
9.5
14
mA (max)
1
7
µA (max)
1
2
µA (max)
DISD
Digital Powerdown Current
fMCLK = 12.288MHz
Output Mode = "0000" Powerdown Mode
AISD
Analog Powerdown Current
fMCLK = 12.288MHz
Output Mode = "0000" Powerdown Mode
DIST
Digital Standby Current
fMCLK = 12.288MHz
Output Mode = "0001" Standby Mode
1.4
2
mA (max)
AIST
Analog Standby Current
fMCLK = 12.288MHz
Output Mode = "0001" Standby Mode
230
1000
µA (max)
VFS_LS
Full-Scale Output Voltage
(Mono speaker amplifier)
CLASS = 0; 0dB gain setting; 8Ω BTL load (7)
2.5
VP-P
VFS_HP
Full-Scale Output Voltage
(Headphone amplifier)
0dB gain setting; 32Ω Stereo Load (7)
2.5
VP-P
2.0
V
0.07
%
VMIC_BIAS Mic Bias Voltage
THD+N
Headphone Amplifier Total
Harmonic Motion Distortion + Noise
fIN = 1 kHz, POUT = 7.5mW; 32Ω Stereo Load
POHP
Headphone Amplifier Output Power
THD+N = 0.5%, fOUT = 1kHz
27
POLS
Mono Speaker Amplifier Output
Power
THD+N = 1%, fOUT = 1kHz
1
PSRR
Power Supply Rejection Ratio
CBYPASS = 1.0µF
CDAC_REF = 1.0µF
VRIPPLE = 200mVP-P @ 217Hz, MIC_P,
MIC_N terminated with 10Ω to ground
55
(1)
(2)
(3)
(4)
(5)
(6)
(7)
20
mW (min)
W
45
dB (min)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which specifies specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
All voltages are measured with respect to the relevant GND pin unless otherwise specified.
Best operation is achieved by maintaining 3.0V ≤ AVDD ≤ 5.0 and 3.0V ≤ DVDD ≤ 3.6V. AVDD must be equal to or greater than DVDD. for
proper operation.
Typicals are measured at 25°C and represent the parametric norm.
Limits are specified to Texas Instrument’s AOQL (Average Outgoing Quality Level).
Datasheet min/max specification limits are ensured by design, test, or statistical analysis.
This value represents the 0dB output level of the given amplifier for the given analog supply voltage. Gain values given in the
GAINCONFIG register are relative to these full-scale values for each output amplifier.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
9
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Electrical Characteristics DVDD = 3.3V, AVDD = 5V, RLHP = 32Ω, RLHF = 8Ω(1)(2)(3) (continued)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA= 25°C.
Parameter
LM4930
Test Conditions
Typ
(4)
Limits (5) (6)
Units
(Limits)
SNR
(Voice)
Signal-to-Noise Ratio
(Voice DAC Path)
Signal = Vo at f = 1kHz @1% THD+N, 32Ω
Stereo Load; Noise = digital zero, Aweighted, 0dB gain setting
72
dB
SNR
(Music)
Signal-to-Noise Ratio (Music Audio
Path)
Signal = Vo at f = 1kHz @1% THD+N, 32Ω
Stereo Load; Noise = digital zero, Aweighted; 0dB gain setting
86
dB
DR
(Voice)
Dynamic Range (Voice DAC Path)
Signal = Vo at f = 1kHz @1% THD+N, 32Ω
Stereo Load; Noise for -60dBFS digital input;
A-weighted; 0dB gain setting
72
dB
DR
(Music)
Dynamic Range (Music Audio Path)
Signal = Vo at f=1kHz @1% THD+N, 32Ω
Stereo Load; Noise for -60dBFS digital input;
A-weighted, 0dB gain setting
86
dB
SNRADC
Signal-to-Noise Ratio
(Voice ADC Path)
Reference signal = 0dBFS
MIC_P, MIC_N terminated with 10Ω to
ground;
A-weighted; 47dB MIC preamp gain setting
75
dB
DRADC
Dynamic Range
(Voice ADC Path)
Reference signal = 0dBFS
Noise for -60dBFS digital input;
A-weighted; 47dB MIC preamp gain setting
75
dB
XTALK
Stereo Channel-to-Channel
Crosstalk
fS = 48kHz, fIN = 1kHz sinewave at -3dBFS
75
dB
VMIC-IN
Maximum Differential MIC Input
Voltage
17dB MIC Preamp gain setting
570
mVP-P
RVDAC
Voice DAC Ripple
300Hz - 3.3kHz through head-phone output.
+/-0.15
+/-0.2
dB (max)
RVADC
Voice ADC Ripple
300Hz - 3.3kHz through head-phone output.
+/-0.25
+/-0.3
dB (max)
PBVDAC
Voice DAC Passband
-3dB Point
SBAVDAC
Voice DAC Stopband Attenuation
Above 4kHz
3.46
kHz
72
dB
UPBVADC Voice ADC Upper Passband Cutoff
Frequency.
Upper -3dB Point
3.47
kHz
LPBVADC
Voice ADC Lower Passband Cutoff
Frequency.
Lower -3dB Point
0.230
kHz
SBAVADC
Voice ADC Stopband Attenuation
Above 4kHz
65
dB
Centered on 55Hz, figure gives worst case
attenuation for 50Hz & 60Hz.
58
dB
+/-0.1
SBANOTC Voice ADC Notch Attenuation
H
RDAC
Audio DAC Ripple
20Hz - 20kHz through head-phone output.
PBDAC
Audio DAC Passband Width
-3dB point
SBADAC
Audio DAC Stopband Attenuation
DRDAC
Audio DAC Dynamic Range Digital
Filter Section
SNRDAC
Audio DAC SNR Digital Filter
Section
ΔACH-CH
+/-0.2
dB (max)
22.7
kHz
Above 24kHz
76
dB
Signal = VO at f = 1kHz @ 1% THD+N;
f = 1kHz; Noise for -60dBFS digital input;
0dB gain; A-weighted
97
dB
Signal = VO at f = 1kHz @ 1% THD+N;
f = 1kHz; Noise for -60dBFS digital input;
0dB gain; A-weighted
97
dB
Stereo Channel-to-Channel Gain
Mismatch
0.3
dB
VIL
Digital Input: Logic Low Voltage
Level
0.4
V
VIH
Digital Input: Logic High Voltage
Level
1.4
V
10
Volume Control Range (Headphone
amplifiers)
Maximum Attenuation
Minimum Attenuation
-46.5
0
dB
dB
Volume Control Range (Mono
speaker amplifier)
Minimum Gain
Maximum Gain
-34.5
12
dB
dB
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Electrical Characteristics DVDD = 3.3V, AVDD = 5V, RLHP = 32Ω, RLHF = 8Ω(1)(2)(3) (continued)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA= 25°C.
Parameter
Test Conditions
Volume Control Step Size (Output
amplifiers)
Volume Control Range (Microphone
Preamp)
Minimum Gain
Maximum Gain
Volume Control Step Size
(Microphone Preamp)
Side Tone Attenuation Range
Maximum Attenuation
Minimum Attenuation
Side Tone Attenuation Step Size
fMCLK
MCLK frequency
CLOCK_DIV = 0
CLOCK_DIV = 1
LM4930
Typ
(4)
Limits (5) (6)
Units
(Limits)
1.5
dB
17
47
dB
dB
2
dB
-30
0
dB
dB
3
dB
12.288
24.576
MHz
MHz
MCLK Duty Cycle
50
fCONV
Sampling Clock Frequency (8)
48
kHz
fCLKSCL
SCL_CLK Frequency
400
kHz
tRISESCL
SCL_CLK, SCL_DATA Rise Time
300
ns
tFALLSCL
SCL_CLK, SDA_DATA Fall Time
300
ns
tSDAH
SDA_DATA Hold Time
500
ns
tSDAS
SDA_DATA Setup Time
500
ns
fCLKPCM
PCM_CLK Frequency
128
256
512
kHz
PCM_SYNC_MODE = 00
PCM_SYNC_MODE = 01
PCM_SYNC_MODE = 10
PCM_CLK Duty Cycle
fCLKI2S
I2S_CLK Frequency
50
I2S_RES = 0
I2S_RES = 1
I2S_CLK Duty Cycle
(8)
40
60
40
60
1.536
3.072
50
% (min)
% (max)
% (min)
% (max)
MHz
40
60
% (min)
% (max)
The sampling clock frequency is equal to the master clock frequency divided by 256. (fconv = fMCLK/256)
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
11
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Electrical Characteristics DVDD = 3V, AVDD = 3V, RLHP = 32Ω, RLHF = 8Ω (1) (2) (3)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA= 25°C.
Parameter
LM4930
Test Conditions
Typ
(4)
Limits (5) (6)
Units
(Limits)
7
mA (max)
fMCLK = 12.288MHz
DIDD
Digital Power Supply Current
Output Mode = "0010"
Output Mode = "0011"
Output Mode = "0100"
1.6
Output Mode = "0101"
Output Mode = "0110"
Output Mode = "0111"
3.8
Output Mode = "1000"
Output Mode = "1001"
Output Mode = "1010"
4.2
fMCLK = 12.288MHz; No Load
AIDD
Analog Power Supply Quiescent
Current
Output Mode = "0010"
5.8
Output Mode = "0011"
5.1
Output Mode = "0100"
6.5
Output Mode = "0101"
6.4
Output Mode = "0110"
5.8
Output Mode = "0111"
7.0
Output Mode = "1000"
Output Mode = "1001"
Output Mode = "1010"
7.5
12
mA (max)
1
7
µA (max)
DISD
Digital Powerdown Current
fMCLK = 12.288MHz
Output Mode = "0000" Powerdown Mode
AISD
Analog Powerdown Current
fMCLK = 12.288MHz
Output Mode = "0000" Powerdown Mode
0.6
1.5
µA (max)
DIST
Digital Standby Current
fMCLK = 12.288MHz
Output Mode = "0001" Standby Mode
1.1
1.7
mA (max)
AIST
Analog Standby Current
fMCLK = 12.288MHz
Output Mode = "0001" Standby Mode
100
300
µA (max)
VFS_LS
Full-Scale Output Voltage
(Mono speaker amplifier)
CLASS = 0; 0dB gain setting; 8Ω BTL load (7)
2.5
VP-P
VFS_HP
Full-Scale Output Voltage
(Headphone amplifier)
0dB gain setting; 32Ω Stereo Load (7)
2.5
VP-P
2
V
0.07
%
VMIC_BIAS Mic Bias Voltage
THD+N
Headphone Amplifier Total
Harmonic Distortion + Noise
fIN = 1kHz, POUT = 7.5mW
POHP
Headphone Amplifier Output Power
THD+N = 0.5%, fOUT = 1kHz
25
15
mW (min)
POLS
Mono Speaker Amplifier Output
Power
THD+N = 1%, fOUT = 1kHz
330
270
mW (min)
PSRR
Power Supply Rejection Ratio
CBYPASS = 1.0µF
CDAC_REF = 1.0µF
VRIPPLE = 200mVP-P @ 217Hz
50
42
dB (min)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
12
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which specifies specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
All voltages are measured with respect to the relevant GND pin unless otherwise specified.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX ,θJA, and the ambient temperature,
TA. The maximum allowable power dissipation is PDMAX = (TJMAX – TA) / θJA or the number given in Absolute Maximum Ratings,
whichever is lower. For the LM4930, see power derating currents for more information.
Typicals are measured at 25°C and represent the parametric norm.
Limits are specified to Texas Instrument’s AOQL (Average Outgoing Quality Level).
Datasheet min/max specification limits are ensured by design, test, or statistical analysis.
This value represents the 0dB output level of the given amplifier for the given analog supply voltage. Gain values given in the
GAINCONFIG register are relative to these full-scale values for each output amplifier.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Electrical Characteristics DVDD = 3V, AVDD = 3V, RLHP = 32Ω, RLHF = 8Ω(1)(2)(3) (continued)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA= 25°C.
Parameter
Test Conditions
LM4930
Typ
(4)
Limits (5) (6)
Units
(Limits)
SNR
(Voice)
Signal-to-Noise Ratio
(Voice DAC Path)
Signal = Vo at f = 1kHz @1% THD+N, 32Ω
Stereo Load; Noise = digital zero, Aweighted; 0dB gain setting
72
dB
SNR
(Music)
Signal-to-Noise Ratio (Music Audio
Path)
Signal = Vo at f = 1kHz @1% THD+N, 32Ω
Stereo Load; Noise = digital zero, Aweighted; 0dB gain setting
86
dB
DR
(Voice)
Dynamic Range (Voice DAC Path)
Signal = Vo at f = 1kHz @1% THD+N, 32Ω
Stereo Load; Noise for -60dBFS digital input;
A-weighted, 0dB gain setting
72
dB
DR
(Music)
Dynamic Range (Music Audio Path)
Signal = Vo at f=1kHz @1% THD+N, 32Ω
Stereo Load; Noise for -60dBFS digital input;
A-weighted, 0dB gain setting
86
dB
SNRADC
Signal-to-Noise Ratio
(Voice ADC Path)
Reference signal = 0dBFS
MIC_P, MIC_N terminated with 10Ω to
ground;
A-weighted; 47dB MIC preamp gain setting
75
dB
DRADC
Dynamic Range
(Voice ADC Path)
Reference signal = 0dBFS
Noise for -60dBFS digital input;
A-weighted; 47dB MIC preamp gain setting
75
dB
XTALK
Stereo Channel-to-Channel
Crosstalk
fS = 48kHz, fIN = 1kHz sinewave at -3dBFS
73
dB
VMIC-IN
Maximum Differential MIC Input
Voltage
17dB MIC Preamp gain setting
570
mVP-P
RVDAC
Voice DAC Ripple
300Hz - 3.3kHz through head-phone output.
+/-0.15
+/-0.2
dB (max)
RVADC
Voice ADC Ripple
300Hz - 3.3kHz through head-phone output.
+/-0.25
+/-0.3
dB (max)
PBVDAC
Voice DAC Passband
-3dB Point
SBAVDAC
Voice DAC Stopband Attenuation
Above 4kHz
3.46
kHz
72
dB
UPBVADC Voice ADC Upper Passband Cutoff
Frequency.
Upper -3dB Point
3.47
kHz
LPBVADC
Voice ADC Lower Passband Cutoff
Frequency.
Lower -3dB Point
0.230
kHz
SBAVADC
Voice ADC Stopband Attenuation
Above 4kHz
65
dB
Centered on 55Hz, figure gives worst case
attenuation for 50Hz & 60Hz.
58
dB
+/-0.1
SBANOTC Voice ADC Notch Attenuation
H
RDAC
Audio DAC Ripple
20Hz - 20kHz through head-phone output.
PBDAC
Audio DAC Passband Width
-3dB point
SBADAC
Audio DAC Stopband Attenuation
DRDAC
Audio DAC Dynamic Range Digital
Filter Section
SNRDAC
Audio DAC SNR Digital Filter
Section
ΔACH-CH
+/-0.2
dB (max)
22.7
kHz
Above 24kHz
76
dB
Signal = VO at f = 1kHz @ 1% THD+N;
f = 1kHz; Noise for -60dBFS digital input;
0dB gain; A-weighted
97
dB
Signal = VO at f = 1kHz @ 1% THD+N;
f = 1kHz; Noise for -60dBFS digital input;
0dB gain; A-weighted
97
dB
Stereo Channel-to-Channel Gain
Mismatch
0.3
dB
VIL
Digital Input: Logic Low Voltage
Level
0.4
V
VIH
Digital Input: Logic High Voltage
Level
1.4
V
Volume Control Range (Headphone
amplifiers)
Maximum Attenuation
Minimum Attenuation
-46.5
0
dB
dB
Volume Control Range (Mono
speaker amplifier)
Minimum Gain
Maximum Gain
-34.5
12
dB
dB
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
13
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Electrical Characteristics DVDD = 3V, AVDD = 3V, RLHP = 32Ω, RLHF = 8Ω(1)(2)(3) (continued)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA= 25°C.
Parameter
Test Conditions
Volume Control Step Size (Output
amplifiers)
Volume Control Range (Microphone
Preamp)
Minimum Gain
Maximum Gain
Volume Control Step Size
(Microphone Preamp)
Side Tone Attenuation Range
Maximum Attenuation
Minimum Attenuation
Side Tone Attenuation Step Size
fMCLK
MCLK frequency
CLOCK_DIV = 0
CLOCK_DIV = 1
MCLK Duty Cycle
fCONV
Sampling Clock Frequency
fCLKSCL
tRISESCL
LM4930
Typ
(4)
Units
(Limits)
1.5
dB
17
47
dB
2
dB
-30
0
dB
dB
3
dB
12.288
24.576
MHz
MHz
50
See (8)
Limits (5) (6)
40
60
% (min)
% (max)
48
kHz
SCL_CLK Frequency
400
kHz
SCL_CLK, SCL_DATA Rise Time
300
ns
tFALLSCL
SCL_CLK, SDA_DATA Fall Time
300
ns
tSDAH
SDA_DATA Hold Time
500
ns
tSDAS
SDA_DATA Setup Time
500
ns
fCLKPCM
PCM_CLK Frequency
128
256
512
kHz
kHz
kHz
PCM_SYNC_MODE = 00
PCM_SYNC_MODE = 01
PCM_SYNC_MODE = 10
PCM_CLK Duty Cycle
fCLKI2S
I2S_CLK Frequency
50
I2S_RES = 0
I2S_RES = 1
I2S_CLK Duty Cycle
(8)
14
40
60
1.536
3.072
50
% (min)
% (max)
MHz
MHz
40
60
% (min)
% (max)
The sampling clock frequency is equal to the master clock frequency divided by 256. (fconv = fMCLK/256)
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Typical Performance Characteristics
MIC PreAmp + ADC Frequency Response Zoom
(MIC Gain = 17dB)
0
0.4
-10
0.3
-20
0.2
MAGNITUDE (dB)
MAGNITUDE (dB)
MIC PreAmp + ADC Frequency Response
(MIC Gain = 17dB)
-30
-40
-50
-60
(1)
0.1
0
-0.1
-0.2
-70
-0.3
-80
20
50
100 200
500 1k
-0.4
2k 4k
500
1k
FREQUENCY (Hz)
2k
2.5k
3k
3.5k
Figure 8.
MIC PreAmp + ADC Frequency Response
(MIC Gain = 47dB)
MIC PreAmp + ADC Frequency Response Zoom
(MIC Gain = 47dB)
0
0.4
-10
0.3
-20
0.2
MAGNITUDE (dB)
MAGNITUDE (dB)
Figure 7.
-30
-40
-50
-60
0.1
0
-0.1
-0.2
-70
-0.3
-80
20
50
100 200
500 1k
-0.4
2k 4k
500
FREQUENCY (Hz)
1k
1.5k
2k
2.5k
3k
3.5k
FREQUENCY (Hz)
Figure 10.
MIC PreAmp + ADC Frequency Response High Cutoff
(MIC Gain = 17dB)
MIC PreAmp + ADC Frequency Response High Cutoff
(MIC Gain = 47dB)
0
10
20
30
40
50
60
70
80
0
-10
MAGNITUDE (dB)
MAGNITUDE (dB)
Figure 9.
-20
-30
-40
-50
-60
-70
-80
3k
3.5k
4k
4.5k
5k
FREQUENCY (Hz)
3k
3.5k
4k
4.5k
5k
FREQUENCY (Hz)
Figure 11.
(1)
1.5k
FREQUENCY (Hz)
Figure 12.
0dBm0 = -3dBFS for the PCM voice codec and 0dBm0 = -1dBFS for the I2S DAC, unless otherwise specified.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
15
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (1) (continued)
MIC PreAmp + ADC Frequency Response Low Cutoff
(MIC Gain = 47dB)
0
0
-10
-10
MAGNITUDE (dB)
MAGNITUDE (dB)
MIC PreAmp + ADC Frequency Response Low Cutoff
(MIC Gain = 17dB)
-20
-30
-40
-50
-30
-40
-50
-60
-60
-70
-70
-80
-80
100
200
300
400
500
100
300
400
FREQUENCY (Hz)
Figure 13.
Figure 14.
ADC THD+N
vs
MIC Input Voltage
(MIC Gain = 17dB)
ADC THD+N
vs
MIC Input Voltage
(MIC Gain = 47dB)
10
500
5
2
1
0.5
THD + N (%)
2
0.2
0.1
0.05
0.02
0.01
0.005
1
0.5
0.2
0.1
0.05
0.002
0.001
1m 2m 5m 10m 20m 50m 100m
0.02
0.01
600P
500m 1
1m
2m
5m 10m 20m
50m
MIC INPUT VOLTAGE (V PP)
MIC INPUT VOLTAGE (VPP)
Figure 15.
Figure 16.
MIC PreAmp + ADC PSRR
vs
Frequency
Top Trace = 47dB MIC Gain, Bottom Trace = 17dB MIC Gain
Headphone Sense In Hysteresis Loop
(AVDD = 3V)
3
-10
HEADPHONE SENSE OUT (V)
MIC PREAMP + ADC PSRR (dB)
0
-20
-30
-40
-50
-60
-70
-80
-90
-100
200 300
2.5
2
1.5
1
0.5
0
500
800 1k
2k
3k
0
0.5
1
1.5
2
2.5
3
HEADPHONE SENSE IN (V)
FREQUENCY (Hz)
Figure 17.
16
200
FREQUENCY (Hz)
10
5
THD + N (%)
-20
Figure 18.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Typical Performance Characteristics (1) (continued)
I2S DAC Frequency Response
( Handsfree Output)
Headphone Sense In Hysteresis Loop
(AVDD = 5V)
1
0
4
MAGNITUDE (dB)
HEADPHONE SENSE OUT (V)
5
3
2
-1
-2
-3
-4
1
-5
0
-6
0
1
2
3
4
5
20
50 100 200 500 1k 2k
FREQUENCY (Hz)
Figure 20.
I2S DAC Frequency Response Zoom
(Handsfree Output)
I2S DAC Frequency Response Zoom
(Headphone Output)
0.4
1
0.3
0
0.2
0.1
0
-0.1
-0.2
-1
-2
-3
-4
-5
-0.3
-6
20
-0.4
5k
10k
15k
20k
50 100 200 500 1k 2k
FREQUENCY (Hz)
5k 10k 20k
FREQUENCY (Hz)
Figure 21.
Figure 22.
I S DAC Frequency Response Zoom
(Headphone Output)
THD+N
vs
I S Input Voltage
(Handsfree Output, 0dB Handsfree Gain)
2
2
0.4
10
5
0.3
0.2
THD + N (%)
MAGNITUDE (dB)
5k 10k 20k
Figure 19.
MAGNITUDE (dB)
MAGNITUDE (dB)
HEADPHONE SENSE IN (V)
0.1
0
-0.1
2
1
0.5
0.2
0.1
0.05
0.02
0.01
0.005
-0.2
-0.3
0.002
0.001
1m 2m 5m 10m 20m 50m 100m
-0.4
5k
10k
15k
20k
FREQUENCY (Hz)
500m 1
I2 S INPUT VOLTAGE (FFS)
Figure 23.
Figure 24.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
17
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (1) (continued)
THD+N
vs
I S Input Voltage
(Headphone Output, 0dB Headphone Gain)
2
I2S DAC Crosstalk
(Top Trace = Left to Right, Bottom Trace = Right to Left)
0
-10
2
1
0.5
CROSSTALK (dB)
THD + N (%)
10
5
0.2
0.1
0.05
0.02
0.01
0.005
-20
-30
-40
-50
-60
-70
-80
0.002
0.001
1m 2m 5m 10m 20m 50m 100m
-90
20
500m 1
50 100 200 500 1k 2k
5k 10k 20k
FREQUENCY (Hz)
I2 S INPUT VOLTAGE (FFS)
Figure 25.
Figure 26.
MIC Bias Dropout Voltage vs
MIC Bias Current
PCM DAC Frequency Response
(Handsfree Output)
2.5
0
2
MAGNITUDE (dB)
MIC BIAS DROPOUT (V)
-10
1.5
1
-20
-30
-40
-50
-60
0.5
-70
-80
0
0
2
4
6
8
20
10 12 14 16 18
2k 4k
Figure 27.
Figure 28.
PCM DAC Frequency Response Zoom
(Handsfree Output)
PCM DAC Frequency Response
(Headphone Output)
0.
4
0.
3
0.
2
0.
1
0
-10
MAGNITUDE (dB)
MAGNITUDE (dB)
500 1k
FREQUENCY (Hz)
MIC BIAS CURRENT (mA)
0
0.1
0.2
0.3
0.4 2
0
-20
-30
-40
-50
-60
-70
-80
5
0
10
0
20
0
50
0
1
k
2
k
20
4
k
50 100
200
500 1k
2k 4k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 29.
18
50 100 200
Figure 30.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Typical Performance Characteristics (1) (continued)
THD+N
vs
PCM Input Voltage
(Handsfree Output, 0dB Handsfree Gain)
PCM DAC Frequency Response Zoom
(Headphone Output)
0.4
10
5
0.2
0.1
THD + N (%)
MAGNITUDE (dB)
0.3
0
-0.1
-0.2
-0.3
2k
3k
0.2
0.1
0.05
0.02
0.01
0.005
0.002
0.001
1m 2m 5m 10m 20m 50m 100m
-0.4
1k
2
1
0.5
4k
FREQUENCY (Hz)
500m 1
PCM INPUT VOLTAGE (FFS)
Figure 31.
Figure 32.
THD+N
vs
PCM Input Voltage
(Headphone Output, 0dB Headphone Gain)
Crosstalk
(AVDD = 5V and AVDD = 3V, Headphone Output)
0
-10
2
1
0.5
-20
CROSSTALK (dB)
THD + N (%)
10
5
0.2
0.1
0.05
0.02
0.01
0.005
-30
-40
-50
-60
-70
-80
0.002
0.001
1m 2m 5m 10m 20m 50m 100m
-90
-100
20
500m 1
100
1k
10k 20k
FREQUENCY (Hz)
PCM INPUT VOLTAGE (FFS)
Figure 34.
PSRR
vs
Frequency
(AVDD = 3V, RL = 16Ω, Headphone Output)
PSRR
vs
Frequency
(AVDD = 3V, RL = 32Ω, Headphone Output)
0
0
-10
-10
-20
-20
-30
-30
PSRR (dB)
PSRR (dB)
Figure 33.
-40
-50
-60
-40
-50
-60
-70
-70
-80
-80
-90
-90
-100
20
-100
20
100
1k
10k
100k
100
1k
10k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 35.
Figure 36.
100k
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
19
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (1) (continued)
PSRR
vs
Frequency
(AVDD = 5V, RL = 16Ω, Headphone Output)
0
0
-10
-10
-20
-20
-30
-30
PSRR (dB)
PSRR (dB)
PSRR
vs
Frequency
(AVDD = 3V, RL = 8Ω, Handsfree Output)
-40
-50
-60
-40
-50
-60
-70
-70
-80
-80
-90
-90
-100
20
-100
20
100
1k
10k
100k
100
1k
10k
100k
FREQUENCY (Hz)
Figure 37.
Figure 38.
PSRR
vs
Frequency
(AVDD = 5V, RL = 32Ω, Headphone Output)
PSRR
vs
Frequency
(AVDD = 5V, RL = 8Ω, Handsfree Output)
0
0
-10
-10
-20
-20
-30
-30
PSRR (dB)
PSRR (dB)
FREQUENCY (Hz)
-40
-50
-60
-40
-50
-60
-70
-70
-80
-80
-90
-90
-100
20
-100
20
100
1k
10k
100k
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 39.
Figure 40.
THD+N
vs
Frequency
(AVDD = 3V, RL = 8Ω, PO = 150mW, Handsfree Output)
THD+N
vs
Frequency
(AVDD = 5V and AVDD = 3V, RL = 16Ω, PO = 15mW,
Headphone Output)
10
10
5
1
THD+N (%)
THD + N (%)
2
0.5
0.2
1
0.1
0.1
0.05
0.02
0.01
20
50 100 200 500 1k 2k
5k 10k 20k
100
1k
10k 20k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 41.
20
0.01
20
Figure 42.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Typical Performance Characteristics (1) (continued)
THD+N
vs
Frequency
(AVDD = 5V and AVDD = 3V, RL = 32Ω, PO = 7.5mW,
Headphone Output)
THD+N
vs
Frequency
(AVDD = 5V, RL = 8Ω, PO = 250mW, Handsfree Output)
10
10
5
THD + N (%)
THD+N (%)
2
1
0.1
1
0.5
0.2
0.1
0.05
0.02
0.01
20
0.01
100
1k
10k 20k
20
50 100 200 500 1k 2k
FREQUENCY (Hz)
5k 10k 20k
FREQUENCY (Hz)
Figure 43.
Figure 44.
THD+N
vs
Output Power
AVDD = 3V, RL = 16Ω, f = 1kHz, Headphone Output)
THD+N
vs
Output Power
(AVDD = 3V, RL = 8Ω, f = 1kHz, Handsfree Output)
10
10
5
2
THD+N (%)
THD + N (%)
1
0.1
1
0.5
0.2
0.1
0.05
0.02
0.01
1
10
0.01
10m
100
OUTPUT POWER (mW)
20m
50m 100m 200m
500m
1
OUTPUT POWER (W)
Figure 45.
Figure 46.
THD+N
vs
Output Power
(AVDD = 5V and AVDD = 3V, RL = 32Ω, f = 1kHz, Headphone
Output)
THD+N
vs
Output Power
(AVDD = 5V and AVDD = 3V, RL = 16Ω, f = 1kHz, Headphone
Output)
1
1
THD+N (%)
10
THD+N (%)
10
0.1
0.1
0.01
0.01
1
10
50
1
OUTPUT POWER (mW)
10
100
OUTPUT POWER (mW)
Figure 47.
Figure 48.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
21
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (1) (continued)
THD+N
vs
Output Power
(AVDD = 5V, RL = 8Ω, f = 1kHz, Handsfree Output)
10
5
THD + N (%)
2
1
0.5
0.2
0.1
0.05
0.02
0.01
10m
20m
50m 100m 200m 500m 1
2
OUTPUT POWER (W)
Figure 49.
22
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
APPLICATION INFORMATION
REFERENCE DESIGN BOARD AND LAYOUT
LM4930ITL Board Layout
Figure 50. LM4930ITL Demo Board Schematic
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
23
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Figure 51. LM4930ITL Demo Board Composite View
Figure 52. LM4930ITL Demo Board Silkscreen
24
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Figure 53. LM4930ITL Demo Board Top Layer
Figure 54. LM4930ITL Demo Board Bottom Layer
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
25
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Figure 55. LM4930ITL Demo Board Inner Layer 1
Figure 56. LM4930ITL Demo Board Inner Layer 2
26
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Figure 57. Pin Markings for LM4930ITL demo board
BILL OF MATERIALS FOR LM4930
Table 4. LM4930 Demo Board Bill Of Materials
Comment
Footprint
Designators
1k
0805
R6, R7
2k
0805
R2, R3
20k
0805
R1
100k
0805
R5
1M
0805
R4
22pF
1210
C6, C7
0.01µF cer
1210
C16, C17
0.1µF cer
1210
C14, C15
1µF
1210
C1, C2, C3, C4, C5, C10, C11, C12, C13
220µF
7243
C8, C9
CRYSTAL
7243
Y1
PHONE JACK STEREO SW STEREO HEADPHONE JACK (3.5MM) J8
Table 5. Two-Wire Control Interface (J1)
Pin
Function
1
DVDD
2
SCL
3
DGND
4
NC
5
DGND
6
SDA
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
27
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Table 6. PCM Interface (P4, P3, P1, P2)
Header
Function
P1
PCM_SDI
P2
PCM_CLK
P3
PCM_SYNC
P4
PCM_SDO
Table 7. I2S Interface (J2)
Pin
Function
1
MCLK
2
I2S-CLK
3
I2S-DATA
4
I2S-WS
5
DGND
6
DGND
7
DGND
8
DGND
9
DGND
10
DGND
Table 8. MIC Jack
Pin
Function
1
AGND
2
MIC-
3
MIC+
Table 9. Misc Jumpers and Headers
DVDD/DGND (J10)
Pin
Function
1
DGND
2
AVDD
Table 10. Misc Jumpers and Headers
AVDD/AGND (J9)
Pin
Function
1
AGND
2
AVDD
Table 11. Misc Jumpers and Headers
MCLK/XTAL_IN (P5)
Pin
Function
1
DGND
2
MCLK/XTAL_IN
28
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
ADR SELECT (S1)
Jumper IN = LOW
Control interface responds to addresses 001000b (BASICCONFIG), 0010001b (VOICETESTCONFIG)), and
0010010b (GAINCONFIG)
Jumper OUT = HIGH
Control interface responds to addresses 111000b (BASICCONFIG), 1110001b (VOICETESTCONFIG)), and
1110010b (GAINCONFIG)
Table 12. HP Sense Out (J6)
Pin
Function
1
AGND
2
HPSense_Out
Table 13. IRQ (J4)
Pin
Function
1
DGND
2
IRQ
Onboard MCLK Select (S2)
Jumper IN = Onboard MCLK
Jumper OUT = External MCLK
LM4930ITL DEMO BOARD OPERATION
The LM4930ITL demo board is a complete evaluation platform, designed to give easy access to the control pins
of the part and comprise all the necessary external passive components. Besides the separate analog (J9) and
digital (J10) supply connectors, the board features seven other major input and control blocks: a two wire
interface bus (J1) for the control lines, a PCM interface bus (P1-P4) for voiceband digital audio, an I2S interface
bus (J2) for full-range digital audio, an analog mic jack input (J3) for connection to an external microphone, a
BTL mono output (J7) for connection to an external speaker, a stereo headphone output (J8), and an external
MCLK input (P5) for use in place of the crystal on the demoboard.
Two-wire Interface Bus (J1)
This is the main control bus for the LM4930. It is a two-wire interface with an SDA line (data) and SCL line
(clock). Each transmission from the baseband controller to the LM4930 is given MSB first and must follow the
timing intervals given in the Electrical Characteristics section of the datasheet to create the start and stop
conditions for a proper transmission. The start condition is detected if SCL is high on the falling edge of SDA.
The stop condition is detected if SCL is high on the rising edge of SDA. Repeated start signals are handled
correctly. Data is then transmitted as shown in Figure 4. After the start condition has been achieved the chip
address is sent, followed by a set write bit, wait for ack (SDA will be pulled low by LM4930), data bits 15-8, wait
for ACK (SDA will be pulled low by LM4930), data bits 7-0, wait for ACK (SDA will be pulled low by LM4930)and
finally the stop condition is given.
This same sequence follows for any control bus transmission to the LM4930. The chip address is hardwire
selected by the ADR Select pin which may be jumpered high or low with its application at S1 on the demo board.
The chip address is then given as a combination of the identifying bits for the LM4930 plus the 2-bit address of
the desired control register (00b = BasicConfig, 01b = VoicetestConfig, 10b = GainConfig). Acceptable addresses
are shown here in Table 14.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
29
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
Table 14. LM4930 Control Bus Addresses
Address Bits
Register Address
ADR = 0
6
5
4
3
2
1
0
0
0
1
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
1
0
1
1
1
0
0
0
0
1
1
1
0
0
0
1
1
1
1
0
0
1
0
ADR = 1
Data is sampled only if the address is in range and the R/W bit is clear. Data for each register is given in the
System Control Registers section of the datasheet. Texas Instruments also features a special control board for
quick evaluation of the LM4930 demo board with your PC. This is a serial control interface board, complete with
header compatible with the interface header (J1) on the LM4930 board. This also features demonstration
software to allow for complete control and evaluation of the various modes and functions of the LM4930 through
the bus.
Pullup resistors are required to achieve reliable operation. 750Ω pullup resistors on the SDA and SCL lines
achieves best results when used with TI's parallel-to-serial interface board. Lower value pullup resistors will
decrease the rise and fall times on the bus which will in turn decrease susceptibility to bus noise that may cause
a false trigger. The cost comes at extra current use. Control bus reliability will thus depend largely on bus noise
and may vary from design to design. Low noise is critical for reliable operation.
PCM Bus Interface (P1, P2, P3, P4)
PCM_SDO (P4), PCM_SYNC (P3), PCM_SDI (P1), and PCM_CLK (P2) form the PCM interface bus for simple
communication with most baseband ICs with voiceband communications and follow the PCM-1900
communications standard. The PCM interface features frame lengths of 16, 32, or 64 bits, A-law and u-law
companding, linear mode, short or long frame sync, an energy-saving power down mode, and master only
operation.
The PCM bus does not support a slave mode. It operates as a master only. Thus PCM_SYNC and PCM_CLK
are solely generated by the LM4930. PCM_SYNC is the word sync line for the bus. It operates at a fixed
frequency of 8kHz and may be set in the BASICCONFIG register (bit 5 PCM_LONG) for short or long frame
sync. A short frame sync is 1 PCM_CLK cycle (PCM_LONG=0), a long frame sync is 2 PCM_CLK cycles long
(PCM_LONG=1). A long sync pulse is also delayed one clock cycle relative to a short sync pulse. This is
illustrated in Figure 5. PCM_CLK is the bit clock for the bus. It's frequency depends on the number of 16-bit
frames per sync pulse and can be 128kHz, 256kHz, 512kHz.
The other two lines, PCM_SDO and PCM_SDI, are for serial data out and serial data in, respectively. The type of
data may also be set in the BASICCONFIG register by bits 6 and 7. Bit 6 controls whether the data is linear or
companded. If set to 1, the 8 MSBs are presumed to be companded data and the 8 LSBs are ignored. If cleared
to 0, the data is treated as 2's complement PCM data. Bit 7 controls which PCM law is used if Bit 6 is set for
companded (G711) data. If set to 1, the companded data is assumed to be A-law. If cleared to 0, the companded
data is treated as µ-law.
Bits 8:9 of the BASICCONFIG register set the PCM_SYNC_MODE settings. This controls the number of 16 bit
frames per sync pulse. The feature allows the LM4930 to function harmoniously with other devices or channels
on the PCM bus by adjusting the number of 16 bit frames per sync pulse to 1 (00b), 2 (01b), or 4 (10b). The
LM4930 will transmit PCM data in the first frame and then tri-state the PCM_SDO pin on later frames.
In addition, the LM4930 provides control to allow the PCM_CLK and PCM_SYNC clocks to continue functioning
even when the LM4930 is in Standby mode. By setting bit 10 of the BASICCONFIG register to 1
PCM_ALWAYS_ON is enabled and the LM4930 will continue to drive the PCM clock and sync lines when in
Standby mode. This bit should be set if another codec is using the PCM bus. Powerdown mode will disable these
outputs.
30
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
I2S Interface Bus (J2)
The I2S standard provides a uni-directional serial interface designed specifically for digital audio. For the
LM4930, the interface provides access to a 48kHz, 16 bit full-range stereo audio DAC. This interface uses a
three port system of clock (I2S_CLK), data (I2S_DATA), and word (I2S_WS). The clock and word lines can be
either master or slave as set by bit 11 in the BASICCONFIG register.
A bit clock (I2S_CLK) at 32 or 64 times the sample frequency is established by the I2S system master and a
word select (I2S_WS) line is driven at a frequency equal to the sampling rate of the audio data, in this case
48kHz. The word line is registered to change on the negative edge of the bit clock. The serial data (I2S_DATA) is
sent MSB first, again registered on the negative edge of the bit clock, delayed by 1 bit clock cycle relative to the
changing of the word line (typical I2S format - see Figure 6).
The resolution of the I2S interface may be set by modifying the I2S_RES bit (bit 12) in the BASICCONFIG
register. If set to 1, the LM4930 operates at 32 bits per frame (3.072MHz). If cleared to 0, then 16 bits per frame
is selected (1.536MHz). This has a corresponding effect on the bit clock.
The I2S Interface Bus also provides for an additional MCLK connection to an external device from the LM4930
demo board. This may be used in conjunction with Texas Instruments' SPDIF->I2S Conversion Board for quick
evaluation. This board features a connection header that interfaces with pins 1-5 of the I2S Interface Bus. Pins 610 are provided as digital ground references for the case of discrete connections.
MCLK/XTAL_IN (P5)
This is the input for an external Master Clock. The jumper at S2 must be removed (disconnecting the onboard
crystal from the circuit) when using an external Master Clock.
BTL Mono Out (J7)
This is the mono speaker output, designed for use with an 8 ohm speaker. The outputs are driven in bridge-tiedload (BTL) mode, so both sides have signal. Outputs are normally biased at one half AVDD when the LM4930 is
in active mode.
Additionally, if the CLASS bit is set to 1 in the VOICETESTCONFIG register (bit 0) the BTL mono output is
internally configured as a buffer amplifier designed for use with an external class D amp.
Stereo Headphone Out (J8)
This is the stereo headphone output. Each channel is single-ended, with 220uF DC blocking capacitors mounted
on the demo board. The jack features a typical stereo headphone pinout.
A headphone sense pin is provided at J6. This pin provides a clean logic high or low output to indicate the
presence of headphones in the headphone jack. A common application circuit for this is given in the Reference
Board Schematic shown in Figure 50. In this application HPSENSE_IN is pulled low by the 1k ohm resistor when
no headphone is present. This gives a corresponding logic low output on the HPSENSE_OUT pin. When a
headphone is placed in the jack the 1k ohm pull-down is disconnected and a 100k ohm pull-up resistor creates a
high voltage condition on HPSENSE_IN. This in turn creates a logic high on HPSENSE_OUT. This output may
be used to reliably drive an external microcontroller with headphone status.
MIC Jack (J3)
This jack is for connection to an external microphone like the kind typically found in mobile phones. Pin 1 is
GND, pin 2 is the negative input pin, and pin 3 is the positive pin, with phantom voltage supplied by MIC_BIAS
on the LM4930.
IRQ (J4)
This pin provides simple status updates from the LM4930 to an external microcontroller if desired. IRQ is logic
high when the LM4930 is in a stable state and changes to low when changing modes. This can also be useful for
simple software/driver development to monitor mode changes, or as a simple debugging tool.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
31
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
BASIC OPERATION
The LM4930 is a highly integrated audio subsystem with many different operating modes available. These
modes may be controlled in the BASICCONFIG register in bits 3:0. These mode settings are shown in the
BASICCONFIG register table and are described here below:
Powerdown Mode (0000b)
Part is powered down, analog outputs are not biased. This is a minimum current mode. All part features are shut
down.
Standby Mode (0001b)
The LM4930 is powered down, but outputs are still biased at one half AVDD. This comes at some current cost,
but provides a much faster turn-on time with zero "click and pop" transients on the headphone out. Standby
mode can be toggled into and out of rapidly and is ideal for saving power whenever continuous audio is not a
requirement. All other part functions are suspended unless PCM_ALWAYS_ON (bit 10 in BASICCONFIG
register) is enabled, in which case PCM_CLK and PCM_SYNC will continue to function.
Mono Speaker Mode (0010b)
Part is active. All analog outputs are biased. Audio from the voiceband codec is routed to the mono speaker out.
Stereo headphone out is silent.
Headphone Call Mode (0011b)
Part is active. All analog outputs are biased. Audio from voiceband codec is routed to the stereo headphones.
Both left and right channels are the same. Mono speaker out is silent.
Conference Call Mode (0100b)
Part is active. All analog outputs are biased. Audio from the voiceband codec is routed to the mono speaker out
and to the stereo headphones.
L+R Mixed to Mono Speaker (0101b)
Part is active. All analog outputs are biased. Full-range audio from the 16bit/48kHz audio DAC is mixed together
and routed to the mono speaker out. Stereo headphones are silent.
Headphone Stereo Audio (0110b)
Part is active. All analog outputs are biased. Full-range audio from the 16bit/48kHz audio DAC is sent to the
stereo headphone jack. Each channel is heard discretely. The mono speaker is silent.
L+R Mixed to Mono Speaker + Stereo Headphone Audio (0111b)
Part is active. All analog outputs are biased. Full-range audio from the 16bit/48kHz audio DAC is sent discretely
to the stereo headphone jack and also mixed together and sent to the mono speaker out.
Mixed Mode (1000b)
Part is active. All analog outputs are biased. This provides one channel (the left channel) of full range audio to
the mono speaker out. Audio from the voiceband codec is then sent to the stereo headphones, the same on
each channel.
Mixed Mode (1001b)
Part is active. All analog outputs are biased. Mixed voiceband and full-range audio (left channel only) is sent to
the mono speaker out. Audio from the voiceband codec only is sent to the stereo headphones, the same on each
channel.
32
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
LM4930
www.ti.com
SNAS212C – JULY 2003 – REVISED MAY 2013
Mixed Mode (1010b)
Part is active. All analog outputs are biased. Audio from the voiceband codec is sent to the mono speaker out.
The left channel only of the full range audio is then sent to both the left and right channels of the stereo
headphone out.
REGISTERS
The LM4930 starts on power-up with all registers cleared in Powerdown mode. Powerdown mode is the
recommended time to make setup changes to the digital interfaces (PCM bus, I2S bus). Although the
configuration registers can be changed in any mode, changes made during Standby or Powerdown prevent
unwanted audio artifacts that may occur during rapid mode changes with the outputs active. The LM4930 also
features a soft reset. This reset is enabled by setting bit 4 of the BASICCONFIG register.
The VOICETESTCONFIG register is used to set various configuration parameters on the voiceband and fullrange audio codecs. SIDETONE_ATTEN (bits 4:1) refers to the level of signal from the MIC input that is fed back
into the analog audio output path (commonly used in headphone applications and killed in hands-free
applications). Setting the AUTOSIDE bit (bit 5) automatically mutes the sidetone in voice over mono speaker
modes so feedback isn't an issue.
Quick mute functions are also located in this register, with bits 13:15 muting the mono speaker amp, the
headphone amp, and the mic preamp respectively.
This register also has a CLOCK_DIV bit (bit 6) which, if set, allows for the use of a 24.576MHz clock instead of
the default 12.288MHz.
The GAINCONFIG register is used to control the gain of the mono speaker amp , the headphone amp, and the
mic preamp. This allows flexible mono speaker gains from -34.5dB to +12dB in 1.5dB steps, headphone amp
gains of -46.5dB to 0dB in 1.5dB steps, and mic preamp gains of 17dB to 47dB in 2dB steps. Gain levels may be
modified in any mode, but may wait for a zero cross detect in the DAC to eliminate volume control artifacts. This
wait for zero cross may be disabled by setting the ZXD_DISABLE bit (bit 7) in the VOICETESTCONFIG register
to allow immediate changes.
ANALOG INPUTS AND OUTPUTS
The LM4930 features an analog mono BTL output for connection to an 8Ω external speaker. This output can
provide up to 1W of power into an 8Ω load with a 5V analog supply. A single-ended stereo headphone output is
also featured, providing up to 30mW of power per channel into 32Ω with a 5V analog supply.
A Headphone Sense output is provided on J6 for connection to an external controller. This pin goes high when a
heaphone is present (when used as shown in Figure 50) and will function in all modes independent of other
operations the LM4930 may be currently processing.
The MIC Jack input (J3) provides for a low level analog input. Pin 3 provides the power to the MIC and the
positive input of the LM4930. Gain for the MIC preamp is set in the GAINCONFIG register.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
33
LM4930
SNAS212C – JULY 2003 – REVISED MAY 2013
www.ti.com
REVISION HISTORY
Changes from Revision B (May 2013) to Revision C
•
34
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 33
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM4930
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
LM4930ITLX/NOPB
ACTIVE
DSBGA
YZR
36
1000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-30 to 85
G
B6
LM4930LQ/NOPB
ACTIVE
WQFN
NJN
44
250
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-30 to 85
L4930LQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Sep-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LM4930ITLX/NOPB
DSBGA
YZR
36
1000
178.0
12.4
LM4930LQ/NOPB
WQFN
NJN
44
250
178.0
16.4
Pack Materials-Page 1
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.43
3.59
0.76
8.0
12.0
Q1
7.3
7.3
1.3
12.0
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Sep-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM4930ITLX/NOPB
DSBGA
YZR
36
1000
210.0
185.0
35.0
LM4930LQ/NOPB
WQFN
NJN
44
250
210.0
185.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
YZR0036xxx
D
0.600±0.075
E
TLA36XXX (Rev D)
D: Max = 3.458 mm, Min =3.397 mm
E: Max = 3.292 mm, Min =3.232 mm
4215058/A
NOTES:
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
www.ti.com
12/12
MECHANICAL DATA
NJN0044A
LQA44A (REV B)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising