Texas Instruments | 1-W Mono Audio Power Amplifier with Headphone Drive (Rev. D) | Datasheet | Texas Instruments 1-W Mono Audio Power Amplifier with Headphone Drive (Rev. D) Datasheet

Texas Instruments 1-W Mono Audio Power Amplifier with Headphone Drive (Rev. D) Datasheet
TPA0253
1-W MONO AUDIO POWER AMPLIFIER
WITH HEADPHONE DRIVE
SLOS280D – JANUARY 2000 – REVISED NOVEMBER 2002
D Ideal for Notebook Computers, PDAs, and
D
D
D
D
D
D
D
D
D
D
Other Small Portable Audio Devices
1 W Into 8-Ω From 5-V Supply
0.3 W Into 8-Ω From 3-V Supply
Stereo Head Phone Drive
Mono (BTL) Signal Created by Summing
Left and Right Signals Internally
Wide Power Supply Compatibility
2.5 V to 5.5 V
Low Supply Current
– 3.2 mA Typical at 5 V
– 2.7 mA Typical at 3 V
Shutdown Control . . . 1 µA Typical
Shutdown Pin Is TTL Compatible
–40°C to 85°C Operating Temperature
Range
Space-Saving, Thermally-Enhanced MSOP
Packaging
DGQ PACKAGE
(TOP VIEW)
FILT_CAP
SHUTDOWN
VDD
BYPASS
RIN
1
2
3
4
5
10
9
8
7
6
LO/MO–
LIN
GND
ST/MN
RO/MO+
description
The TPA0253 is a 1-W mono bridge-tied-load (BTL) amplifier designed to drive speakers with as low as 8-Ω
impedance. The mono signal is created by summing left and right inputs internally. The amplifier can be
reconfigured on the fly to drive two stereo single-ended (SE) signals into headphones. This makes the device
ideal for use in small notebook computers, PDAs, digital personal audio players, anyplace a mono speaker and
stereo headphones are required. From a 5-V supply, the TPA0253 can deliver 1-W of power into an 8-Ω speaker.
The gain of the input stage is set by the user-selected input resistor and a 50-kΩ internal feedback resistor
(AV = – RF/RI). The power stage is internally configured with a gain of –1.25 V/V in SE mode, and –2.5 V/V in
BTL mode. Thus, the overall gain of the amplifier is 62.5 kΩ/RI in SE mode and 125 kΩ/RI in BTL mode. The
input terminals are high-impedance CMOS inputs, and can be used as summing nodes.
The TPA0253 is available in the 10-pin thermally-enhanced MSOP package (DGQ) and operates over an
ambient temperature range of –40°C to 85°C.
AVAILABLE OPTIONS
TA
PACKAGED DEVICES
MSOP†
(DGQ)
MSOP
SYMBOLIZATION
– 40°C to 85°C
TPA0253DGQ
AEL
† The DGQ package are available taped and reeled. To order a taped and reeled part, add the
suffix R to the part number (e.g., TPA0253DGQR).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TPA0253
1-W MONO AUDIO POWER AMPLIFIER
WITH HEADPHONE DRIVE
SLOS280D – JANUARY 2000 – REVISED NOVEMBER 2002
schematic
CBYP
4
BYPASS
VDD
3
VDD
GND
1
8
BYPASS
FILT_CAP
VDD
50 kΩ
1 µF
50 kΩ
1.25*R
100 kΩ
5
Right
Audio
Input
Ci
RIN
M
U
X
–
R
–
+
CC
RO/MO+
6
+
Ri
BYPASS
BYPASS
100 kΩ
50 kΩ
Stereo/Mono
Control
50 kΩ
ST/MN
7
LO/MO–
10
50 kΩ
1.25*R
Left
Audio
Input
Ci
Ri
9
LIN
M
U
X
–
R
–
+
+
1 kΩ
BYPASS
BYPASS
From
System Control
2
2
SHUTDOWN
CC
Shutdown
and Depop
Circuitry
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPA0253
1-W MONO AUDIO POWER AMPLIFIER
WITH HEADPHONE DRIVE
SLOS280D – JANUARY 2000 – REVISED NOVEMBER 2002
Terminal Functions
TERMINAL
NAME
NO.
I/O
I
DESCRIPTION
BYPASS
4
FILT_CAP
1
Midrail bias voltage
GND
8
LIN
9
I
Left-channel input terminal
LO/MO–
10
O
Left-output in SE mode and mono negative output in BTL mode.
RIN
5
I
Right-channel input terminal
RO/MO+
6
O
Right-output in SE mode and mono positive output in BTL mode
SHUTDOWN
2
I
TTL-compatible shutdown terminal
ST/MN
7
I
Selects between stereo and mono mode. When held high, the amplifier is in SE stereo mode; while held
low, the amplifier is in BTL mono mode.
VDD
3
I
Positive power supply
Terminal used to filter power supply
Ground terminal
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD +0.3 V
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . internally limited (see Dissipation Rating Table)
Operating free-air temperature range, TA (see Table 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE
DGQ
TA ≤ 25°C
2.14 W§
DERATING FACTOR
17.1 mW/°C
TA = 70°C
1.37 W
TA = 85°C
1.11 W
‡ Please see the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report
(SLMA002), for more information on the PowerPAD package. The thermal data was measured on a PCB
layout based on the information in the section entitled Texas Instruments Recommended Board for PowerPAD
on page 33 of that document.
PowerPAD is a trademark of Texas Instruments.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TPA0253
1-W MONO AUDIO POWER AMPLIFIER
WITH HEADPHONE DRIVE
SLOS280D – JANUARY 2000 – REVISED NOVEMBER 2002
recommended operating conditions
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Supply voltage, VDD
High-level
High
level in
input
ut voltage, VIH
VDD = 3 V
VDD = 5 V
ST/MN
MAX
2.5
5.5
V
4.5
V
2
VDD = 3 V
VDD = 5 V
ST/MN
UNIT
2.7
SHUTDOWN
Low-level
input
Low level in
ut voltage, VIL
MIN
1.65
2.75
V
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
SHUTDOWN
0.8
Operating free-air temperature, TA
– 40
°C
85
electrical characteristics at specified free-air temperature, VDD = 3 V, TA = 25°C (unless otherwise
noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PARAMETER
TEST CONDITIONS
MIN
|VOO|
Output offset voltage (measured differentially)
RL = 4 Ω, ST/MN = 0 V, SHUTDOWN = 2 V
PSRR
Power supply rejection ratio
VDD = 2.9 V to 3.1 V, BTL mode
SHUTDOWN, VDD = 3.3 V,
VI = VDD
|IIH|
High level input current
High-level
|IIL|
Low level input current
Low-level
ZI
IDD
Input impedance
IDD(SD)
Supply current, shutdown mode
RF
Feedback resistor
ST/MN, VDD = 3.3 V,
TYP
MAX
UNIT
30
mV
65
dB
1
1
SHUTDOWN, VDD = 3.3 V,
VI = VDD
VI = 0 V
ST/MN, VDD = 3.3 V,
VI = 0 V
1
A
µA
1
µA
A
50
Supply current
VDD = 2.5 V, SHUTDOWN = 2 V
SHUTDOWN = 0 V
VDD = 2.5 V, RL = 4 Ω, ST/MN = 1.375 V,
SHUTDOWN = 2 V
47
kΩ
2.7
4
mA
1
10
µA
50
57
kΩ
operating characteristics, VDD = 3 V, TA = 25°C, RL = 8 Ω, f = 1 kHz (unless otherwise noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PARAMETER
TEST CONDITIONS
BTL mode,
Gain = 14 dB
THD = 0.1%
Gain = 1.9 dB
SE mode,
RL = 32 Ω
PO
Output power, see Note 1
THD + N
Total harmonic distortion plus
noise
PO = 250 mW,
f = 20 Hz to 20 kHz
BOM
Maximum output power bandwidth
Gain = 1.9 dB,
THD = 2%
Vn
Supple ripple rejection ratio
kHz
f = 1 kHz,
0 47 µF
F
C(BYP) = 0.47
Noise output voltage
C(BYP) = 0.47
0 47 µF
µF,
f = 20 Hz to 20 kHz
NOTE 1: Output power is measured at the output terminals of the device at f = 1 kHz.
4
MIN
THD = 0.1%,
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TYP
MAX
UNIT
300
30
mW
0.2%
20
BTL mode
46
SE mode
68
BTL mode
83
SE mode
33
kHz
dB
µVRMS
TPA0253
1-W MONO AUDIO POWER AMPLIFIER
WITH HEADPHONE DRIVE
SLOS280D – JANUARY 2000 – REVISED NOVEMBER 2002
electrical characteristics at specified free-air temperature, VDD = 5 V, TA = 25°C (unless otherwise
noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PARAMETER
TEST CONDITIONS
MIN
|VOO|
Output offset voltage (measured differentially)
RL = 4 Ω, ST/MN = 0 V, SHUTDOWN = 2 V
PSRR
Power supply rejection ratio
VDD = 4.9 V to 5.1 V, BTL mode
SHUTDOWN, VDD =5.5 V,
VI = VDD
TYP
MAX
UNIT
30
mV
62
dB
1
µA
A
|IIH|
High level input current
High-level
|IIL|
Low level input current
Low-level
ZI
IDD
Input impedance
Supply current
SHUTDOWN = 2 V
3.2
4.8
mA
IDD(SD)
Supply current, shutdown mode
SHUTDOWN = 0 V
1
10
µA
ST/MN, VDD = 5.5 V,
SHUTDOWN, VDD = 5.5 V,
ST/MN, VDD = 5.5 V,
VI = VDD
VI = 0 V
1
VI = 0 V
1
1
A
µA
50
kΩ
operating characteristics, VDD = 5 V, TA = 25°C, RL = 8 Ω, f = 1 kHz (unless otherwise noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁ
PARAMETER
TEST CONDITIONS
THD = 0.1%,
BTL mode
THD = 0.1%,
SE mode,
PO
Output power (see Note 1)
THD + N
Total harmonic distortion plus
noise
PO = 1 W,
f = 20 Hz to 20 kHz
BOM
Maximum output power
bandwidth
Gain = 8 dB,
THD = 2%
Supple ripple rejection ratio
kHz
f = 1 kHz,
0 47 µF
F
C(BYP) = 0.47
Noise output voltage
C(BYP) = 0.47
0 47 µF,
F
f = 20 Hz to 20 kHz
Vn
MIN
RL = 32 Ω
TYP
MAX
UNIT
1
W
85
mW
0.33%
20
BTL mode
46
SE mode
60
BTL mode
85
SE mode
34
kHz
dB
µV
VRMS
NOTE 1: Output power is measured at the output terminals of the device at f = 1 kHz.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
PACKAGE OPTION ADDENDUM
www.ti.com
6-Sep-2019
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TPA0253DGQ
ACTIVE
HVSSOP
DGQ
10
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
AEL
TPA0253DGQG4
ACTIVE
HVSSOP
DGQ
10
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
AEL
TPA0253DGQR
ACTIVE
HVSSOP
DGQ
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
AEL
TPA0253DGQRG4
ACTIVE
HVSSOP
DGQ
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
AEL
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
6-Sep-2019
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Sep-2019
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TPA0253DGQR
Package Package Pins
Type Drawing
SPQ
HVSSOP
2500
DGQ
10
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
330.0
12.4
Pack Materials-Page 1
5.3
B0
(mm)
K0
(mm)
P1
(mm)
3.4
1.4
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Sep-2019
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPA0253DGQR
HVSSOP
DGQ
10
2500
358.0
335.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising