Texas Instruments | LM48560 Evaluation Board | User Guides | Texas Instruments LM48560 Evaluation Board User guides

Texas Instruments LM48560 Evaluation Board User guides
User's Guide
SNAU196 – December 2015
LM48560 Evaluation Board
This user's guide describes the characteristics, operation, and use of the LM48560 Evaluation Module
(EVM). A complete schematic diagram, printed-circuit board layouts, and bill of materials (BOM) are
included in this document.
3
4
5
6
7
8
9
10
11
Contents
Introduction ...................................................................................................................
Quick Start Guide ............................................................................................................
2.1
Hardware Mode .....................................................................................................
2.2
Software Mode ......................................................................................................
General Description .........................................................................................................
Board Features ...............................................................................................................
Operating Conditions ........................................................................................................
Application Circuit Schematic ..............................................................................................
Connections ..................................................................................................................
PCB Layout Guidelines .....................................................................................................
Bill Of Materials ..............................................................................................................
Example Initialization Register Setting ....................................................................................
Demonstration Board PCB Layout ........................................................................................
1
LM48560 Demonstration Board ............................................................................................ 2
2
Demonstration Board Schematic .......................................................................................... 4
3
Top Silk Screen .............................................................................................................. 7
4
Solder Mask Top ............................................................................................................. 7
5
Top Layer ..................................................................................................................... 7
6
Layer 2 ........................................................................................................................ 7
7
Layer 3 ........................................................................................................................ 7
8
Drill Drawing .................................................................................................................. 7
9
Silk Bottom.................................................................................................................... 8
10
Solder Mask Bottom ......................................................................................................... 8
11
Bottom Layer ................................................................................................................. 8
1
2
2
2
2
3
3
3
3
4
5
5
6
6
7
List of Figures
List of Tables
1
Operating Conditions ........................................................................................................ 3
2
Connections .................................................................................................................. 5
3
LM48560 Bill of Materials ................................................................................................... 6
4
Example Initialization Register Setting .................................................................................... 6
All trademarks are the property of their respective owners.
SNAU196 – December 2015
Submit Documentation Feedback
LM48560 Evaluation Board
Copyright © 2015, Texas Instruments Incorporated
1
Introduction
1
www.ti.com
Introduction
To help the user investigate and evaluate the LM48560 performance and capabilities, a fully-populated
demonstration board was created. Figure 1 shows the board. Connected to an external power supply (2.7
V ≤ VDD ≤ 5.5 V) and a signal source, the LM48560 demonstration board easily exercises the amplifier’s
features.
Figure 1. LM48560 Demonstration Board
2
Quick Start Guide
2.1
Hardware Mode
Use the following steps to set up the EVM board in hardware mode:
Step 1. Short pins 1 (VDD) and 2 of JU1 for normal operation.
Step 2. Short pins 2 and 3 (GND) of JU7 to set the device in hardware mode.
Step 3. Short pins 1 and 2 of JU3 to select IN2 and enable boost.
Step 4. Short pins 1 and 2 of JU2 for gain of 30 V/V.
Step 5. Connect a power supply (2.7 V–5.5 V) and ground reference, respectively, to the VDD and
GND headers on the demo board.
Step 6. Connect a differential audio input to IN2+ and IN2–.
Step 7. Power on the board and observe the output on OUT+ and OUT–.
2
LM48560 Evaluation Board
SNAU196 – December 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Quick Start Guide
www.ti.com
2.2
Software Mode
Use the following steps to set up the EVM board in software mode:
Step 1. Short pins 1 (VDD) and 2 of JU1 for normal operation.
Step 2. Short pins 1 (VDD) and 2 of JU7 to set the device in software mode
Step 3. Short pins 1 (VDD) and 2 of JU3 to select IN2 and enable boost.
Step 4. Short pins 2 and 3 (GND) of JU2 for 24-dB gain.
Step 5. Connect a power supply (2.7 V–5.5 V) and ground reference, respectively, to the VDD and
GND headers on the demo board.
Step 6. Connect a differential audio input on IN2+ and IN2–.
Step 7. Connect a USB/I2C board to the LM48560 demo board.
Step 8. Connect the USB/I2C board to a PC.
Step 9. Turn on the power supply.
Step 10. Launch the LM48560 software GUI (SNAC051).
Step 11. Verify that the bottom left corner of the GUI reads “USB Connected ALL ACK”.
If the GUI reads “USB I/O error NAK” the device has not been acknowledged, please double
check connections.
Step 12. Select the following:
• INPUT SELECT = INPUT 1
• BOOST = ON
• TURN ON TIME = NORMAL
• GAIN = 0dB
3
General Description
The LM48560 is a high-voltage, high-efficiency, Class H driver for ceramic speakers and piezo actuators.
The LM48560’s Class H architecture offers significant power savings compared to traditional Class AB
amplifiers. The device provides 30Vp-p output drive while consuming just 4 mA of quiescent current from
a 3.6-V supply.
The LM48560 features two fully-differential inputs with separate gain settings, and a selectable control
interface. In software control mode, the gain control and device modes are configured through the I2C
interface. In hardware control mode, the gain and input mux are configured through a pair of logic inputs.
The LM48560 has a low power shutdown mode that reduces quiescent current consumption to 0.1 μA.
4
Board Features
The LM48560 high voltage class H ceramic speaker driver with automatic level control demonstration
board has all of the necessary connections using 0.100” headers connectors to apply the power supply
voltage, audio input signals, and audio output (speaker). The amplified audio signal is only available on
the audio output header.
5
Operating Conditions
Table 1 lists the temperature range and supply voltage conditions for the EVM.
Table 1. Operating Conditions
Temperature Range: TMIN ≤ TA ≤ TMAX
–40°C ≤ TA ≤ 85°C
Supply Voltage (VDD)
2.7 V ≤ VDD ≤ 5.5 V
SNAU196 – December 2015
Submit Documentation Feedback
LM48560 Evaluation Board
Copyright © 2015, Texas Instruments Incorporated
3
Application Circuit Schematic
6
www.ti.com
Application Circuit Schematic
Figure 2 shows the demonstration board schematic.
VDD
L1
U1
SW D3
4.7uH
D2
VDD
TP1
VDD
C1
10uF
C2
1uF
D4
D1
PGND
GND
TP2
VDD
A2
VBST C1
SGND
JU1
VDD
1
2
3
JU2
B2
C3
1uF
C4
0.22uF
JU7
SW/HW C2
SCL
1
2
3
C3
VDD
SDA
VDD
IN1+
JU3
JU6
1
2
3
SDA/SEL C4
A4
1
2
3
SCL/GAIN
C5
0.47uF
JU4
SET D1
IN1+
C11
1uF
C6
0.47uF
A3
IN1-
VDD
SHDN
R2
5.1K
SCL
IN1-
J1
1
SCL
I2CVDD 4
VDD
C9
0.47uF
B4
OUT+ A1
IN2+
IN2+
JU5
R1
OUT+
UNSTUFFED
C10
0.47uF
B3
OUT- B1
IN2-
IN2-
C8
UNSTUFFED
2
ADR
R3
5.1K
OUT-
SDA
3
SDA
GND 5
LM48560TL
Figure 2. Demonstration Board Schematic
4
LM48560 Evaluation Board
SNAU196 – December 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Connections
www.ti.com
7
Connections
Table 2 describes the connections on the EVM board.
Table 2. Connections
8
Designator
Function
Notes
VDD
VDD
Power supply
GND
GND
Ground reference
OUT+
OUTPUT
Positive output terminal
OUT–
OUTPUT
Negative output terminal
IN1+
INPUT 1
Positive input terminal 1
IN1–
INPUT 1
Negative input terminal 1
IN2+
INPUT 2
Positive input terminal 2
IN2–
INPUT 2
Negative input terminal 2
JU1
Shutdown
Short pin 1 (VDD) and pin 2 for normal operation. Short pin 2 and pin 3 (GND) for device
shutdown.
JU2
SCL/Gain Select
Hardware mode: Short pin 2 to pin 1 (VDD) for higher gain. Short pin 2 to pin 3 (GND) for
lower gain.
Software mode: Keep pins 1-3 open. Pin 2 = SCL for I2C communication
JU3
SDA/Input Select
Hardware mode: Short pin 2 to pin 1 (VDD) to select IN2. Short pin 2 to pin 3 (GND) to
select IN1.
Software mode: Keep pins 1-3 open. Pin 2 = SDA for I2C communication
JU4
SCL Pullup
Short JU4 to connect pullup resistor to VDD. Open to use external I2C supply voltage
JU5
SDA pullup
Short JU5 to connect pullup resistor to VDD. Open to use external I2C supply voltage
JU6
I2C VDD
Short JU6 to use VDD as I2C VDD. Open to use external I2C supply voltage
JU7
SW/HW
Hardware Mode: Short pins 2 and 3 (GND)
Software Mode: Short pins 1 (VDD) and 2
PCB Layout Guidelines
Minimize trace impedance of the power, ground and all output traces for optimum performance. Voltage
loss due to trace resistance between the LM48560 and the load results in decreased output power and
efficiency. Trace resistance between the power supply and ground has the same effect as a poorly
regulated supply; increased ripple and reduced peak output power. Use wide traces for power supply
inputs and amplifier outputs to minimize losses due to trace resistance, as well as route heat away from
the device. Proper grounding improves audio performance, minimizes crosstalk between channels and
prevents switching noise from interfering with the audio signal. Use of power and ground planes is
recommended.
Place all digital components and route digital signal traces as far as possible from analog components and
traces. Do not run digital and analog traces in parallel on the same PCB layer. If digital and analog signal
lines must cross either over or under each other, ensure that they cross in a perpendicular fashion.
SNAU196 – December 2015
Submit Documentation Feedback
LM48560 Evaluation Board
Copyright © 2015, Texas Instruments Incorporated
5
Bill Of Materials
9
www.ti.com
Bill Of Materials
Table 3 details the EVM BOM.
Table 3. LM48560 Bill of Materials
10
Designator
Description
Part Number
U1
LM48560TL IC
LM48560TL/NOPB
Footprint
Value
Qty
C1
CAP_TANTALUM-CHIP_B
TPSB106K016R0800
B case
10uF
1
C4
CAP_0603_CERAMIC-CHIP
GCM188R71H224KA64D
603
0.22uF
1
C8
1210 Ceramic Capacitor
C3225X7R1E685K
1210
UNSTUFFED
0
C2, C3
CAP_0603_CERAMIC-CHIP
GRM188R61E105KA12D
603
1uF
2
C11
CAP_0603_CERAMIC-CHIP
GRM188R71H104KA93D
603
0.1uF
1
C5,C6,C9,C10
CAP_0603_CERAMIC-CHIP
GRM188R61A474KA61D
603
0.47uF
4
D1
Schottky Diode
PD3S120L-7
PowerDI
323
20V
1
GND, IN+, IN-,
IN2+, IN2-, JU4,
JU5, JU6, OUT+,
OUT-, VDD
2-pin Header
87220-2
100 mil
11
J1
2-pin Header + 3-pin Header
100 mil
2
JU1, JU2, JU3,
JU7
3-pin Header
87220-3
100 mil
4
L1
INDUCTOR_CHIP_1515_MURATA
LQH44PN4R7MP0L
1515
4.7uH
1
R1
RES_0805_CHIP
ERJ-P06J100V
805
UNSTUFFED
0
R2, R3
603 Thick Film Resistor
CRCW06035K10JNEA
603
5.1k
2
TP1, TP2
TESTPOINT-PC5000
87220-1
100 mil
1
2
Example Initialization Register Setting
Table 4 provides an initialization register setting example.
Table 4. Example Initialization Register Setting
6
Register
Data
Data (Binary)
0x00h
0x01h
00000011
Description
Turn on time = 15 ms. Input 1 selected. Boost enabled, device
enabled
0x01h
0x00h
00000000
Release time = 0.5 s. Attack time = 0.83 ms. Voltage limit disabled.
(Release/Attack time depends on Cset, more details in LM48560
datasheet (SNAS513))
0x02h
0x00h
00000000
Gain = 21 dB (Gain depends on boost enable/disable)
LM48560 Evaluation Board
SNAU196 – December 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Demonstration Board PCB Layout
www.ti.com
11
Demonstration Board PCB Layout
Figure 3 through Figure 11 show the different layers used to create the LM48560 demonstration board.
Figure 3 is the top silk screen that shows component locations on the board’s top surface. Figure 5 is the
top layer, Figure 6 is layer 2, Figure 7 is layer 3, and Figure 11 is the bottom layer.
Figure 3. Top Silk Screen
Figure 4. Solder Mask Top
Figure 5. Top Layer
Figure 6. Layer 2
SNAU196 – December 2015
Submit Documentation Feedback
LM48560 Evaluation Board
Copyright © 2015, Texas Instruments Incorporated
7
Demonstration Board PCB Layout
www.ti.com
Figure 7. Layer 3
Figure 8. Drill Drawing
Figure 9. Silk Bottom
Figure 10. Solder Mask Bottom
Figure 11. Bottom Layer
8
LM48560 Evaluation Board
SNAU196 – December 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising