Texas Instruments | SRC4190/92/93EVM - | User Guides | Texas Instruments SRC4190/92/93EVM - User guides

Texas Instruments SRC4190/92/93EVM - User guides
User’s Guide
June 2003
SBAU088
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products & application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated
EVM IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION
PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided
may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective
considerations, including product safety measures typically found in the end product incorporating the goods.
As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic
compatibility and therefore may not meet the technical requirements of the directive.
Should this evaluation kit not meet the specifications indicated in the EVM User’s Guide, the kit may be returned
within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE
WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED,
IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user
indemnifies TI from all claims arising from the handling or use of the goods. Please be aware that the products
received may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). Due to the open construction
of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic
discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE
TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not
exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein.
Please read the EVM User’s Guide and, specifically, the EVM Warnings and Restrictions notice in the EVM
User’s Guide prior to handling the product. This notice contains important safety information about temperatures
and voltages. For further safety concerns, please contact the TI application engineer.
Persons handling the product must have electronics training and observe good laboratory practice standards.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any
machine, process, or combination in which such TI products or services might be or are used.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the specified input and output ranges described in
the EVM User’s Guide.
Exceeding the specified input range may cause unexpected operation and/or irreversible
damage to the EVM. If there are questions concerning the input range, please contact a TI
field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or
possible permanent damage to the EVM. Please consult the EVM User’s Guide prior to
connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than
60°C. The EVM is designed to operate properly with certain components above 60°C as long
as the input and output ranges are maintained. These components include but are not limited
to linear regulators, switching transistors, pass transistors, and current sense resistors. These
types of devices can be identified using the EVM schematic located in the EVM User’s Guide.
When placing measurement probes near these devices during operation, please be aware
that these devices may be very warm to the touch.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated
Contents
Preface
About This Manual
This document provides the information needed to setup and operate the
SRC4192EVM evaluation module. For a more detailed description of the
SRC4190, SRC4192, or SRC4193 products, please refer to the product data
sheets available from the Texas Instruments web site at http://www.ti.com.
Support documents are listed in the sections of this guide entitled Related Documentation from Texas Instruments and Additional Documentation.
How to Use This Manual
Throughout this document, the abbreviation EVM and the term evaluation
module are synonymous with the SRC4192EVM. The abbreviation
SRC419x refers to the SRC4190, SRC4192. and SRC4193 family of devices.
Chapter 1 provides an overview of the SRC419x family of stereo asynchronous sample rate converters. The SRC4192EVM block diagram and primary features are also discussed.
Chapter 2 provides general information regarding EVM handling and unpacking, absolute operating conditions, and the default switch and jumper
configuration.
Chapter 3 is the hardware setup guide for the EVM, providing all of the necessary information needed to configure the EVM switches and jumpers for
product evaluation.
Chapter 4 includes the EVM electrical schematic, PCB layout, and the Bill
of Materials.
Information About Cautions and Warnings
This book contains cautions.
This is an example of a caution statement.
A caution statement describes a situation that could potentially
damage your software or equipment.
Contents
iii
Contents
This is an example of a warning statement.
A warning statement describes a situation that could potentially
cause harm to you.
The information in a caution or a warning is provided for your protection.
Please read each caution and warning carefully.
Related Documentation From Texas Instruments
The following documents provide information regarding Texas Instruments
integrated circuits used in the assembly of the SRC4192EVM. These documents are available from the TI web site. The last character of the literature
number corresponds to the document revision, which is current at the time
of the writing of this User’s Guide. Newer revisions may be available from
the TI web site at http://www.ti.com/ or call the Texas Instruments Literature
Response Center at (800) 477–8924 or the Product Information Center at
(972) 644–5580. When ordering, identify the booklet(s) by both title and
literature number.
iv
Data sheets
Literature number
SRC4192/4193 Data Sheet
DIT4192 Data Sheet
PLL1705 Data Sheet
REG1117 Data Sheet
SN74AHC32
SN74AHC244
SN74AHC1G04
SN74AHC1G14
SN74ALVC125 Data Sheet
SN74ALVC244 Data Sheet
SN74ALVC245 Data Sheet
SN74CBTLV3245A Data Sheet
SN74LVC04A Data Sheet
SN74LVC1G07 Data Sheet
SN74LVC1G125 Data Sheet
SBFS022
SBOS229
SLES046
SBVS001
SCLS247G
SCLS226I
SCLS318L
SCLS321K
SCES110E
SCES188B
SCES271B
SCDS034J
SCAS281M
SCES296K
SCES223G
Contents
Additional Documentation
The following documents provide information regarding selected non–TI
components, which are used in the assembly of the SRC4192EVM. These
documents are available from the corresponding manufacturers.
Document
Manufacturer
CS8414 Data Sheet
HCM49 Series Crystals
SC937–02 Data Sheet
Cirrus Logic, http://www.cirrus.com
Citizen, http://www.citizencrystal.com
Scientific Conversion
http://www.scientificonversion.com
Scientific Conversion
http://www.scientificonversion.com
SC979–03 Data Sheet
If You Need Assistance
If you have questions regarding either the use of this evaluation module or
the information contained in the accompanying documentation, please contact the Texas Instruments Product Information Center at (972) 644–5580
or visit the TI web site at www.ti.com.
FCC Warning
This equipment is intended for use in a laboratory test environment only. It
generates, uses, and can radiate radio frequency energy and has not been
tested for compliance with the limits of computing devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable
protection against radio frequency interference. Operation of this equipment in other environments may cause interference with radio communications, in which case the user at his own expense will be required to take
whatever measures may be required to correct this interference.
Trademarks
All trademarks are the property of their respective owners.
Contents
v
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 The SRC4190, SRC4192, and SRC4193 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 EVM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 EVM Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-2
1-3
1-4
2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Electrostatic Discharge Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Absolute Maximum Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Unpacking the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-2
2-2
2-2
2-3
3
Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Power Supply Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.2 Device Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3 Selecting the Input & Output Port Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.4 Selecting the Input & Output Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.5 Selecting an Input Source and an Output Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.6 Selecting the SRC419x Reference Clock Source and Frequency . . . . . . . . . . . . . . . . . . . . 3-7
3.7 Selecting the DIT4192 Master Clock Source and Frequency . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.8 Miscellaneous Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.9 Reset Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
4
Schematic, PCB Layout and Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Component Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
4-1
4-2
4-4
4-7
vii
Contents
Figure 1–1. Functional Block Diagram for the SRC4192 and SRC4193 . . . . . . . . . . . . . . . . . . . . . .
Figure 1–2. Functional Block Diagram for the SRC4192EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–1. SRC4192EVM Schematic Diagram (page 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–2. SRC4192EVM Schematic Diagram (page 2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–3. PCB Silkscreen, Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–4. Top Side Layout (Component Side) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–5. Bottom Side Layout (Solder Side) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3
1-4
4-2
4-3
4-4
4-5
4-6
Table 2–1. Absolute Maximum Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Table 2–2. Default Switch and Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Table 3–1. SRC419x Input & Output Port Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Table 3–2. SRC419x Input & Output Port Data Format Configuration . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Table 3–3. Digital Audio Receiver Output Data Format Configuration . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Table 3–4. Digital Audio Transmitter Input Data Format Configuration . . . . . . . . . . . . . . . . . . . . . . . 3-6
Table 3–5. PLL Reference Clock Selection for the SRC419x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Table 3–6. DIT4192 Master Clock Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Table 3–7. Master Clock Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Table 3–8. PLL Master Clock Selection for the DIT4192 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Table 3–9. Low Group Delay Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Table 3–10. Bypass Mode Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Table 3–11. Mute Function Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Table 3–12. DIT4192 Mono Mode Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Table 4–1. Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
viii
Contents
Electrostatic Discharge Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Contents
ix
Chapter 1
This chapter provides a brief technical overview for the SRC4190, SRC4192,
and SRC4193 asynchronous sample rate converters, as well as a general
description and feature list for the SRC4192EVM.
Topic
Page
1.1
The SRC4190, SRC4192 and SRC4193 . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.2
EVM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.3
EVM Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Introduction
1-1
The SRC4190, SRC4192, and SRC4193
1.1 The SRC4190, SRC4192, and SRC4193
The SRC4192 and SRC4193 are stereo asynchronous sample rate converters designed for professional and broadcast audio applications. Operation at
input and output sampling frequencies up to 212kHz is supported, with an input/output sampling ratio range of 16:1 to 1:16. Excellent dynamic range and
THD+N are achieved by employing high performance, linear phase digital filtering with better than 140dB of image rejection. The SRC4190 is a lower–cost
version of the SRC4192 with reduced performance specifications, but it is
functionally equivalent to the SRC4192 and shares the same pin configuration.
The SRC4190 and SRC4192 are both stand–alone, pin–programmed devices, with control inputs for mode, data format, mute, bypass, and low group
delay functions. The SRC4193 includes a three–wire serial peripheral interface (SPI) port, which allows access to on–chip control registers for device
function configuration. The SPI port can be easily interfaced to microprocessors or digital signal processors with synchronous serial port interfaces.
All three devices offer filtering options, which allow for lower group delay processing. These options include a low group delay mode for the interpolation
function and a direct down–sampling mode (SRC4193 only) for the decimation
function.
The audio input and output ports support standard audio data formats, as well
as a TDM interface mode. Word lengths of 24–, 20–, 18–, and 16–bits are supported. Both ports may operate in Slave mode, deriving their word (LRCK) and
bit (BCK) clocks from external input and output devices. Alternatively, one port
may be operated in Master mode while the other remains in Slave mode. In
Master mode, the LRCK and BCK clocks are derived from the reference clock
(RCKI) input. The flexible configuration of the audio ports allows connection
to a wide variety of audio data converters, digital audio interface devices, and
digital signal processors.
A bypass mode is also included. This mode allows data to be passed directly
from the audio input port to the audio output port, bypassing the sample rate
converter function. The bypass option is useful for passing through encoded
or compressed audio data, or non–audio control and status data. The input
and output port clocks must be synchronous with one another in bypass mode.
A soft mute function is included in all three devices. A digital attenuation function is available only for the SRC4193. Both soft mute and digital attenuation
functions provide artifact free operation, while allowing muting or level adjustment of the audio output signal. The mute attenuation is typically –144dB for
the SRC4192 and SRC4193, and –128dB for the SRC4190. The SRC4193
digital attenuation function is adjustable from 0dB to –127.5dB in 0.5dB steps.
A block diagram of the SRC4192 and SRC4193 is shown in Figure 1–1. The
SRC4190 offers the same functionality as the SRC4192.
1-2
The SRC4190, SRC4192, and SRC4193
Figure 1–1. Functional Block Diagram for the SRC4192 and SRC4193
LRCKI
BCKI
SDIN
MODE[2:0]
IFMT[2:0]
OFMT[1:0]
OWL[1:0]
MUTE
BYPAS
LGRP
/RST
Audio
Input
Port
fsIN
Interpolation
Filters
SPI and
Control Logic
(SRC4193)
LRCKO
BCKO
SDOUT
TDMI
Audio
Output
Port
RCKI
16fsOUT
Rate
Estimator
LRCKO
MUTE
BYPAS
/RST
/CS
CCLK
CDATA
Re–Sampler
REFCLK
LRCKI
Control
Logic
(SRC4192)
16fsIN
/RDY
RATIO (SRC4193 only)
Reference Clock
fsOUT
MUX
REFCLK
fsOUT
Decimation
Filters
Direct
Down–Sampler
(SRC4193 only)
Power
VDD
DGND
VIO
DGND
1.2 EVM Block Diagram
The block diagram for the SRC4192EVM is shown in Figure 1–2. The EVM includes buffered audio input and output ports that support I2S, Left Justified,
Right Justified, and TDM data formats. These ports may be connected to external receivers and transmitters, data converters, or digital signal processors.
An on–board 96kHz receiver is provided, as well as a 192kHz transmitter. The
receiver and transmitter provide for convenient connection to both test and
commercial audio equipment supporting AES3 or S/PDIF interfaces.
The SRC4192 and DIT4192 have their own external phase locked loop circuits
for on–board clock generation. External clock inputs are also available and
provide for additional flexibility. The EVM is configured using on–board
switches and jumpers, in addition to a buffered host port, which supports the
SRC4193 SPI interface. A single +5 volt power supply is all that is needed to
power the EVM. A +3.3 volt supply is derived from the +5 volt supply using an
on–board voltage regulator.
Introduction
1-3
The SRC4190, SRC4192, and SRC4193
1.3 EVM Features
Key features for the SRC4192EVM include:
- Zero Insertion Force (ZIF) socket for easily interchanging SRC4190,
SRC4192 and SRC4193 devices. The Analog Devices AD1895 and
AD1896 are also supported for head–to–head testing.
- On–board or external clock generation.
- On–board receiver and transmitter supports AES3 input and output (75 Ω
BNC connections provided).
- Buffered audio input and output ports using standard dual in–line headers.
- Buffered Host Port supports connection to an external controller
(SRC4193 only).
- Operation from a single +5 volt power supply.
Figure 1–2. Functional Block Diagram for the SRC4192EVM
SRC4192EVM
GND +5V
REG1117
+3.3V
+5V
Audio
Input
Port
Digital
Input
CS8414
Audio
Output
Port
Digital
Output
H
D
R
Transmitter
DIT4192
75 ohm
External
DIT
Clock
B
U
F
B
U
F
Receiver
75 ohm
1-4
H
D
R
B
U
F
Sample
Rate
Converter
H
D
R
Host
Interface
Port
(SRC4193 Only)
SRC4192
or
SRC4193
ZIF Socket
Provided
S
W
DIP Switch
(SRC4192 Only)
B
U
F
Clock
Generator
Clock
Generator
PLL1705
PLL1705
External
SRC
Clock
Introduction
1-5
Chapter 2
This chapter provides information regarding SRC4192EVM handling and
unpacking, absolute operating conditions, and a description of the factory
default switch and jumper configuration.
Topic
Page
2.1
Electrostatic Discharge Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2
Absolute Maximum Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3
Unpacking the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.4
Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Getting Started
2-1
Absolute Maximum Operating Conditions
2.1 Electrostatic Discharge Warning
Many of the components on the SRC4192EVM are susceptible to damage by
electrostatic discharge (ESD). Customers are advised to observe proper ESD
handling precautions when unpacking and handling the EVM, including the
use of a grounded wrist strap at an approved ESD workstation.
Caution: Failure to observe ESD handling procedures may result in
damage to EVM components.
2.2 Absolute Maximum Operating Conditions
The user should be aware of the absolute maximum operating conditions for
the SRC4192EVM. Exceeding these conditions may result in damage to the
EVM. Table 2–1 summarizes the critical data points.
Table 2–1. Absolute Maximum Operating Conditions
Parameter
Maximum Condition
Power Supply
+5.5 VDC maximum
Audio Input and Output Ports, Host Port,
External SRC Clock, External DIT Clock
VIH
VIL
+4.0 Volts maximum
–0.5 Volts minumum
Digital Audio Input (Connector J2)
VIH
VIL
+12 Volts maximum
–12 Volts minumum
2.3 Unpacking the EVM
Upon opening the SRC4192EVM package, please check to make sure that
the following items are included:
- One SRC4192EVM.
- One SRC4192IDB installed in the EVM ZIF socket.
If either of these items are missing, please contact the Texas Instruments
Product Information Center nearest you to inquire about a replacement.
2-2
Default Configuration
2.4 Default Configuration
The factory default switch and jumper settings are shown in Table 2, and result
in the following EVM configuration:
- The SRC4192 Input Port is set to Slave mode, with the CS8414 receiver
selected as the input source.
- The SRC4192 Output Port is set to Slave mode, with the DIT4192 trans-
mitter selected as the output device.
- The SRC PLL (U16) is selected as the SRC419x reference clock source
and is set to 24.576MHz.
- The SRC4192 input and output port data formats are set to 24–Bit Left
Justified.
- The CS8414 receiver output format is set to 24–Bit Left Justified
- The DIT4192 transmitter input format is set to 24–Bit Left Justified
- The DIT4192 transmitter MCLK frequency is set to 256fs, with fs = 48kHz.
- The transmitter PLL (U6) is selected as the DIT4192 MCLK source and is
set to 12.288MHz.
- The DIT4192 transmitter output mode is set to stereo.
- The SRC4192 Low Group Delay, Bypass, and Mute modes are all dis-
abled.
Table 2–2. Default Switch and Jumper Settings
SW1
Set To:
SW3
Set To:
SW6
Set To:
SW7
Set To:
M0
M1
M2
LO
LO
LO
CLK1
CLK0
FMT0
FMT1
LO
HI
LO
LO
TSR
TFS2
TFS1
TPLL
LO
LO
LO
LO
LGRP
BYPAS
IFMT0
IFMT1
IFMT2
MUTE
~4193
IS/M
LO
LO
LO
LO
LO
LO
HI
HI
SW9
Set To:
SW10
Set To:
J8
Set To:
SFS1
SFS2
SSR
~PLL
OM/~S
~IPORT
MONO
MDAT
LO
LO
HI
LO
LO
HI
LO
LO
MODE2
MODE1
MODE0
~PORT
OFMT0
OFMT1
OWL0
OWL1
LO
LO
LO
HI
LO
LO
LO
LO
1–2 (I2S/RJ)
OPEN
3–4 (LJ)
SHORT
Getting Started
2-3
Chapter 3
This chapter provides a step–by–step guide to configuring the SRC4192EVM
for device evaluation. Follow the sections to walk through the setup of the
SRC4192EVM.
Topic
Page
3.1
Power Supply Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.2
Device Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3
Selecting the Input & Output Port Modes . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.4
Selecting the Input & Output Data Format . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.5
Selecting an Input Source and an Output Port . . . . . . . . . . . . . . . . . . . 3-5
3.6
Selecting the SRC419x Reference Clock Source and Frequency . . 3-7
3.7
Selecting the DIT4192 Master Clock Source and Frequency . . . . . . 3-8
3.8
Miscellaneous Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.9
Reset Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Setup Guide
3-1
Power Supply Configuration
3.1 Power Supply Configuration
The SRC4192EVM requires a single +5 volt regulated dc power supply,
connected at the +5V terminal of J9. The GND terminal of J9 should be
connected to the power supply ground or common terminal. The supply
should not be connected to terminal block J9 while hot, as damage may
occur to the EVM. At no time should the power supply exceed the absolute
maximum rating.
3.2 Device Selection
The ~4193 element of switch SW7 is utilized to select the device under
test.
When ~4193 is set to LO, the EVM is configured for the SRC4193. The
SRC4193 is a software–controlled device, which employs an SPI port to
access internal control registers. The SPI port is accessed through the
buffered Host Port at connector J5. The Host Port supports connection to
an external microprocessor or DSP for host control.
When ~4193 is set to HI, the EVM is configured for the SRC4190 or
SRC4192. These units are stand–alone devices and do not require an external host for operation. The user configures the EVM by means of the
on–board switches and jumpers. The Analog Devices AD1895 and AD1896
are also supported in this mode, enabling head–to–head comparison testing.
3-2
Selecting the Input & Output Port Modes
3.3 Selecting the Input & Output Port Modes
The input and output ports of the SRC419x devices support seven modes
of operation. Table 3–1 summarizes the mode settings for the SRC419x
devices. In Master mode, the LRCK and BCK clocks are outputs, derived
from the reference clock (RCKI) input. In Slave mode, the LRCK and BCK
clocks are inputs, which are generated by the audio input or output device.
When ~4193 is set to HI, the port modes are selected using the MODE0,
MODE1, and MODE2 elements of switch SW10.
When ~SRC4193 is set to LO, the MODE[2:0] bits in Control Register 1 of
the SRC4193 are used to select the port modes.
Table 3–1. SRC419x Input & Output Port Mode Selection
MODE2
MODE1
MODE0
Serial Port Mode
LO
LO
LO
Both Input and Output Ports are in Slave mode
LO
LO
HI
Output Port is in Master mode with RCKI = 128fs
LO
HI
LO
Output Port is in Master mode with RCKI = 512fs
LO
HI
HI
Output Port is in Master mode with RCKI = 256fs
HI
LO
LO
Both Input and Output Ports are in Slave mode
HI
LO
HI
Input Port is in Master mode with RCKI = 128fs
HI
HI
LO
Input Port is in Master mode with RCKI = 512fs
HI
HI
HI
Input Port is in Master mode with RCKI = 256fs
Setup Guide
3-3
Selecting the Input & Output Data Formats
3.4 Selecting the Input & Output Data Formats
The SRC419x devices support a flexible set of audio data formats. Table 3–2
summarizes the input and output format options for the sample rate converters. Section 3.5 of this chapter describes the format configuration for the digital
audio receiver and transmitter devices.
When ~4193 is set to HI, the IFMT0, IFMT1 and IFMT2 elements of switch
SW7 are used to select the input port data format. The OFMT0, OFMT1,
OWL0, and OWL1 elements of switch SW10 are used to select the output port
data format and word length.
When ~4193 is set to LO, Control Register 3 of the SRC4193 is used to select
the input and output data formats.
Table 3–2. SRC419x Input & Output Port Data Format Configuration
3-4
IFMT2
IFMT1
IFMT0
Input Port Data Format
LO
LO
LO
24–Bit Left Justified
LO
LO
HI
24–Bit I2S
LO
HI
LO
Unused
LO
HI
HI
Unused
HI
LO
LO
16–Bit Right Justified
HI
LO
HI
18–Bit Right Justified
HI
HI
LO
20–Bit Right Justified
HI
HI
HI
24–Bit Right Justified
OFMT1
OFMT0
Output Port Data Format
LO
LO
Left Justified
LO
HI
I2S
HI
LO
TDM
HI
HI
Right Justified
OWL1
OWL0
Output Port Data Word Length
LO
LO
24–Bits
LO
HI
20–Bits
HI
LO
18–Bits
HI
HI
16–Bits
Selecting an Input Source and an Output Port
3.5 Selecting an Input Source and an Output Port
The ~IPORT element of switch SW9 is utilized to select the input source.
When ~IPORT is set to LO, the buffered Audio Input Port at connector J1 is
selected as the input source. This port is designed to interface to devices that
support Left Justified, Right Justified, and I2S formatted digital audio data.
When selecting the Audio Input Port as the input source, the IS/~M element
of switch SW7 must be set to match the mode of the SRC419x input port (Master or Slave), as described in Section 3.3 of this chapter. The data format of
the external audio device must be set to match the format of the Audio Input
Port.
When ~IPORT is set to HI, connector J2 at the input of the CS8414 digital audio
receiver (U1) is selected as the input source. This port is designed to interface
to digital audio signal generators and devices that output AES3 formatted digital audio data. This includes the S/PDIF outputs of CD and DVD players.
When selecting the digital audio receiver (U1) as the input source, the IS/~M
element of switch SW7 must be set to LO (Slave mode), and the SRC419x input port must be set to Slave mode, as described in Section 3.3 of this chapter.
The output data format of the digital audio receiver must be selected using
switch SW1 and jumper block J8. The receiver output format must match the
input data format of the SRC419x device, as described in Section 3.4 of this
chapter. Table 3–3 summarizes the configuration of switch SW1 and jumper
block J8 for the supported data formats.
Table 3–3. Digital Audio Receiver Output Data Format Configuration
M2
M1
M0
J8
Data Format
LO
LO
LO
Short 3–4 (LJ)
Left Justified, 16– to 24–Bits
LO
HI
LO
Short 1–2 (I2S/RJ)
Philips I2S, 16– to 24–Bits
HI
LO
HI
Short 1–2 (I2S/RJ)
Right Justified, 16–Bits
HI
HI
LO
Short 1–2 (I2S/RJ)
Right Justified, 18–Bits
The ~PORT element of switch SW10 is utilized to select the output port.
When ~PORT is set to LO, the buffered Audio Output Port at connector J3 is
selected as the output port. This port is designed to interface to devices that
support Left Justified, Right Justified, and I2S formatted digital audio data.
When selecting the Audio Output Port as the output port, the OM/~S element
of switch SW9 must be set to match the mode of the SRC419x output port
(Master or Slave), as described in Section 3.3 of this chapter. The data format
of the external audio device must be set to match the format of the Audio Output Port.
Setup Guide
3-5
Selecting an Input Source and an Output Port
When ~PORT = HI, the output of the DIT4192 digital audio transmitter (U5) at
connector J4 is selected as the output port. This port is designed to interface
to digital audio signal analyzers and devices that accept AES3 formatted digital audio data. This includes the S/PDIF inputs of A/V receivers and digital recording devices.
When selecting the digital audio transmitter (U5) as the output port, the setting
of the OM/~S element of switch SW9 will correctly set the Master or Slave
mode for both the SRC419x and DIT4192 devices. The input data format of
the transmitter must be selected using the FMT0 and FMT1 elements of switch
SW3. The format must match the output data format of the SRC419x device,
as described in Section 3.4 of this chapter. Table 3–4 summarizes the transmitter format configuration options using switch SW3.
Table 3–4. Digital Audio Transmitter Input Data Format Configuration
3-6
FMT1
FMT0
Data Format
LO
LO
Left Justified, 16– to 24–Bits
LO
HI
Philips I2S, 16– to 24–Bits
HI
LO
Right Justified, 24–Bits
HI
HI
Right Justified, 16–Bits
Selecting the SRC419x Reference Clock Source and Frequency
3.6 Selecting the SRC419x Reference Clock Source and Frequency
The ~PLL element of switch SW9 is used to select the reference clock source
for the SRC419x. The reference clock input is utilized by the SRC419x rate estimator, as well as the input or output port when configured in Master mode.
The Master mode port derives the LRCK and BCK clock outputs from the reference clock input.
When ~PLL is set to LO, the PLL1705 (U16) is selected as the reference clock
source for the SRC419x. Table 3–5 summarizes the output rate selections for
the PLL1705.
When ~PLL is set to HI, the EXT SRC CLK input (J6) is selected as the reference clock input. The EXT SRC CLK input supports +3.3V CMOS external
clock sources with frequencies up to 50MHz.
Table 3–5. PLL Reference Clock Selection for the SRC419x
SSR
SFS2
SFS1
PLL Output Rate (MHz)
LO
LO
LO
12.288
LO
LO
HI
11.2896
LO
HI
LO
8.192
LO
HI
HI
Reserved
HI
LO
LO
24.576
HI
LO
HI
22.5792
HI
HI
LO
16.384
HI
HI
HI
Reserved
Setup Guide
3-7
Selecting the DIT4192 Master Clock Source and Frequency
3.7 Selecting the DIT4192 Master Clock Source and Frequency
The OM/~S element of switch SW9 and the ~TPLL element of SW6 are used
to select the master clock source for the DIT4192 digital audio transmitter. The
master clock (or MCLK) frequency determines the output frame (or sampling)
rate of the transmitter, in addition to determining the SYNC and SCLK output
rates when the DIT4192 is configured in Master mode. Table 3–6 summarizes
the DIT4192 master clock source options.
When OM/~S is set to HI (that is, the SRC419x output port is the Master and
the DIT4192 is a Slave), the reference clock source for the SRC419x will also
be used as the master clock source for the DIT4192. This ensures synchronization between the SRC419x output port and DIT4192 audio serial port.
Table 3–6. DIT4192 Master Clock Selection
~TPLL
OM/~S
DIT4192 MCLK Source
LO
LO
PLL1705 (U6)
HI
LO
EXT DIT CLK (J7)
X
HI
SRC419x Ref Clock
X = Don’t Care
When OM/~S is set to LO (that is, the SRC419x output port is a Slave and the
DIT4192 is the Master), the ~TPLL element of switch SW6 is utilized to select
the DIT4192 master clock source, as shown in Table 3–6.
When the PLL1705 (U6) is selected as the master clock source, the TSR,
TFS1, and TFS2 elements of switch SW6 are utilized to select the PLL output
rate. Table 3–7 summarizes the PLL output rate options.
Table 3–7. PLL Master Clock Source Selection for the DIT4192
3-8
TSR
TFS2
TFS1
PLL Output Rate (MHz)
LO
LO
LO
12.288
LO
LO
HI
11.2896
LO
HI
LO
8.192
LO
HI
HI
Reserved
HI
LO
LO
24.576
HI
LO
HI
22.5792
HI
HI
LO
16.384
HI
HI
HI
Reserved
Selecting the DIT4192 Master Clock Source and Frequency
When the EXT DIT CLK input at connector J7 is selected as the master clock
source, the device will support an external +3.3V CMOS logic level clock
source with frequencies up to 25MHz.
In addition to DIT4192 master clock source selection, the DIT4192 master
clock divider must be selected using the CLK0 and CLK1 elements of switch
SW3. The master clock source frequency will be divided by the factor listed in
Table 3–8 to determine the transmitter output frame rate, as well as the SYNC
and SCLK clock rate when the DIT4192 is configured in Master mode.
Table 3–8. PLL Master Clock Selection for the DIT4192
CLK1
CLK0
DIT4192 MCLK Divider
LO
LO
Divide by 128
LO
HI
Divide by 256
HI
LO
Divide by 384
HI
HI
Divide by 512
Setup Guide
3-9
Miscellaneous Functions
3.8 Miscellaneous Functions
This section provides information regarding several SRC419x and DIT4192
functions not described previously in this chapter.
Low group delay operation is controlled using the LGRP element of switch
SW7, or by the LGRP bit in Control Register 2 when using the SRC4193. The
low group delay option reduces the overall latency of the interpolation filter by
32/fsIN, where fsIN is the input sampling rate in hertz (Hz). Table 3–9 summarizes Low Group Delay operation.
Table 3–9. Low Group Delay Configuration
LGRP
Low Group Delay Mode
LO
Disabled
HI
Enabled
Bypass mode operation is controlled using the BYPAS element of switch SW7,
or by the BYPAS bit in Control Register 1 when using the SRC4193. When Bypass mode is enabled, the audio data is passed directly from the input port to
the output port without sample rate conversion. This process is useful for passing through encoded audio or non–audio data. In Bypass mode, the mute, dithering, and digital attenuation (SRC4193 only) functions are not available.
Table 3–10 summarizes Bypass mode operation.
Table 3–10.Bypass Mode Configuration
3-10
BYPAS
Bypass Mode
LO
Disabled
HI
Enabled
Miscellaneous Functions
The Mute function is controlled using the MUTE element of switch SW7, or by
the MUTE bit of Control Register 1 when using the SRC4193. This function
employs a soft mute technique, which provides for artifact–free muting of the
SRC419x output port. Table 3–11 summarizes Mute function operation.
Table 3–11. Mute Function Configuration
MUTE
Soft Mute Function
LO
Disabled
HI
Enabled
A Direct Down–Sampling option is available only when using the SRC4193.
It is accessed using the DFLT bit in Control Register 2. Refer to the
SRC4192/4193 data sheet for more details regarding the use of this mode.
The DIT4192 digital audio transmitter supports Single Channel Double Frequency operation, also referred to as Mono mode in the DIT4192 data sheet.
In this mode, the DIT4192 output frame rate is one half the input SYNC clock
rate, with two consecutive samples of a single channel replacing the Left and
Right channel samples of the normal Stereo mode transmission. This mode
is useful when testing 176.4kHz and 192kHz sampling rates on an Audio Precision System Two Cascade/Cascade Plus Dual Domain system, configured in
Dual Channel mode. Only one channel at a time may be tested in this fashion.
The MONO and MDAT elements of switch SW9 are utilized to configure Mono
mode operation. Table 3–12 summarizes the MONO and MDAT options.
Table 3–12.DIT4192 Mono Mode Configuration
Mono
Stereo/Mono Mode Operation
LO
Stereo
HI
Mono
MDAT
Audio/Channel Status Data Selection
LO
Left Channel Audio Data / Channel A
CS Data
HI
Right Channel Audio Data / Channel B
CS Data
Setup Guide
3-11
Reset Functions
3.9 Reset Functions
The SRC4192EVM includes three reset switches, one each for the SRC419x
(SW8), the CS8414 receiver (SW2), and the DIT4192 transmitter (SW4). Each
switch is a momentary contact, normally open push–button with 10kΩ pull–up
resistors to the +3.3V supply. To reset a device, momentarily press, then release, the corresponding reset switch. This allows the user to reset the devices
at will, if necessary or desired.
3-12
Chapter 4
! " # This chapter provides the electrical and physical layout information for the
SRC4192EVM. The bill of materials is included for component and
manufacturer reference.
The schematic diagram is shown, beginning on page 4-2. The printed circuit board layouts are shown on pages 4-4 through 4-6. The bill of materials is shown starting on page 4-7.
Topic
Page
4.1
Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2
PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.3
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Schematic, PCB Layout and Bill of Materials
4-1
Schematic
4.1 Schematic
The complete electrical schematics of for the SRC4192EVM are shown in
Figure 4–1 and Figure 4–2.
Figure 4–1. SRC4192EVM Schematic Diagram (page 1 of 2)
4-2
Schematic
Figure 4–2. SRC4192EVM Schematic Diagram (page 2 of 2)
Schematic, PCB Layout and Bill of Materials
4-3
Component Layout
4.2 Component Layout
The printed circuit board plots for the SRC4192EVM are shown in Figure 4–3
through Figure 4–5. The PCB is a two–layer board, with most components
mounted on the top (or component) side. The power supply bypass capacitors
for U15 are mounted on the bottom (or solder) side of the PCB.
Figure 4–3. PCB Silkscreen, Top Layer
4-4
Component Layout
Figure 4–4. Top Side Layout (Component Side)
Schematic, PCB Layout and Bill of Materials
4-5
Component Layout
Figure 4–5. Bottom Side Layout (Solder Side)
4-6
SRC4192EVM
470
16
R24, R25
R22, R23
(continued on next page)
150
15
R15—R17
R1—R14
13
75
LED1
12
14
JMP1
11
47.5
J9
C44
10
22µF
6
C37—C43
J8
4.7µF
5
C1—C36
9
0.1µF
4
C53, C54
J1, J3, J5
0.01µF
3
C52
J2, J4, J6, J7
68000
pF
2
C45–C48
8
18pF
1
Reference
Designator
7
Value
Item
Table 4–1. Bill of Materials
4.3 Bill of Materials
2
2
3
14
1
1
1
1
3
4
1
7
36
2
1
4
Qty
Per Bd
Panasonic
or equivalent
Panasonic
or equivalent
Panasonic
or equivalent
Panasonic
or equivalent
LUMEX
Samtec
Weidmuller
Samtec
Samtec
Kings Electronics
Kemet
Kemet
Kemet
Kemet
Panasonic
or equivalent
Panasonic
or equivalent
Manufacturer
P470CCT–ND
P150AACT–ND
P75AACT–ND
P47.5FCT–ND
SML–LX1206GC–TR
(DK# 67–1357–1–ND)
TSW–102–07–G–S
1699670000
TSW–102–07–G–D
TSW–105–07–G–D
KC–79–274–M06
T491C226K010AS
T491A475K010AS
C0805C104K5RACTU
C0805C103K5RACTU
ECJ–2YB1H683K
ECJ–2VC1H180J
Mfg Part Number
Resistor, 470 ohms, +/– 1%, 1/10W, Thick Film Chip,
Size = 0805
Resistor, 150 ohms, +/– 1%, 1/4W, Thick Film Chip,
Size = 1210
Resistor, 75 ohms, +/– 1%, 1/4W, Thick Film Chip,
Size = 1210
Resistor, 47.5 ohms, +/– 1%, 1/8W, Thick Film Chip,
Size = 1206
Green LED, SMT, Size = 1206
Terminal Strip, 2–pin (2x1)
Terminal Block, 3.5mm PCB, 2 poles
Terminal Strip, 4–pin (2x2)
Terminal Strip, 10–pin (5x2)
BNC Connector, Female, PC Mount
Chip Capacitor, Tantalum, 22µF +/–10%, 10WV, Size = C
Chip Capacitor, Tantalum, 4.7µF +/–10%, 10WV, Size = A
Chip Capacitor, Ceramic X7R, 0.1µF +/–10%, 50WV,
Size = 0805
Chip Capacitor, Ceramic X7R, 0.01µF +/–10%, 50WV,
Size = 0805
Chip Capacitor, Ceramic X7R, 68000pF +/–10%, 50WV,
Size = 0805
Chip Capacitor, Ceramic NPO/C0G, 18pF +/– 5%, 50WV,
Size = 0805
Description
Bill of Materials
4-7
4-8
SRC4192EVM
SW2, SW4, SW8
T1
T2
U1
U2
U3
U4
U5
U6, U16
U7, U14
U8, U13
U9, U18, U21
U10, U17, U20
U11, U19
U12
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
(continued on next page)
SW7, SW9, SW10
RN5—RN7
21
10K
19
RN1, RN2, RN4
SW1, SW3, SW6
10K
18
R18—R21
Reference
Designator
20
10K
Value
17
Item
1
2
3
3
2
2
2
1
1
1
1
1
1
1
3
3
3
3
3
4
Qty
Per Bd
Table 4–1. Bill of Materials (continued)
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Cirrus Logic
Scientific
Conversion
Scientific
Conversion
OMRON
Grayhill
Grayhill
Bourns
Bourns
Panasonic
or equivalent
Manufacturer
SN74LVC1G07DBV
SN74CBTLV3245APW
SN74ALVC245PW
SN74ALVC244PW
SN74LVC04APW
SN74ALVC125PW
PLL1705DBQ
DIT4192IPW
SN74AHC1G14DBV
SN74AHC32PW
SN74AHC1G04DBV
CS8414–CS
SC979–03
SC937–02
B3S–1000
90HBW08P
90HBW04P
4310R–101–103
4606X–101–103
P10KCCT–ND
Mfg Part Number
Single Buffer w/ Open Drain Output
Octal Bus Switch
Octal Bus Transceiver
Octal Buffer/Driver
Hex Inverter
Quad Buffer w/ Tri–State Outputs
Dual PLL Multiclock Generator
Digital Audio Interface Transmitter
Single Schmitt Trigger Inverter
Quadruple 2–Input OR Gate
Single Inverter
Digital Audio Receiver
SMT Transformer for Digital Interface Transmitter
SMT Transformer for Digital Interface Receiver
Momentary Tact Switch, SMT w/o Ground Terminal
DIP Switch, SMT Gull Leaded Sealed, 8 position
DIP Switch, SMT Gull Leaded Sealed, 4 position
Resistor Network, Single–In–Line, ThruHole Bussed,
10 terminal, 9 element
Resistor Network, Single–In–Line, ThruHole Bussed,
6 terminal, 5 element
Resistor, 10K ohms, +/– 1%, 1/10W, Thick Film Chip,
Size = 0805
Description
Bill of Materials
U22
U23
X1, X2
38
39
40
41
42
43
Reference
Designator
U15 (DUT)
Value
37
Item
1
2
1
4
2
1
1
Qty
Per Bd
Table 4–1. Bill of Materials (continued)
Texas Instruments
Citizen
Enplas–Tesco
3M Bumpon
Samtec
Texas Instruments
Texas Instruments
Manufacturer
SN74AHC244PW
HCM49–27.000MABJT
OTS–28(34)–0.65–01
SJ–5003
SNT–100–BK–G–H
REG1117–3.3
SRC4192IDB
Mfg Part Number
Octal Buffer/Driver
Quartz Crystal, SMT, 27MHz, +/– 50ppm
ZIF Socket for SSOP–28, Pinch (2–contact) type
Rubber Feet, Adhesive Backed
Shorting Blocks
Voltage Regulator, +3.3V
Asynchronous Sample Rate Converter
Description
Bill of Materials
SRC4192EVM
4-9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising