Texas Instruments | ADS7142-Q1 Automotive, 2-Channel, 12-Bit, 140-kSPS, I2C-Compatible ADC With Programmable Threshold and Host Wake-Up Features (Rev. A) | Datasheet | Texas Instruments ADS7142-Q1 Automotive, 2-Channel, 12-Bit, 140-kSPS, I2C-Compatible ADC With Programmable Threshold and Host Wake-Up Features (Rev. A) Datasheet

Texas Instruments ADS7142-Q1 Automotive, 2-Channel, 12-Bit, 140-kSPS, I2C-Compatible ADC With Programmable Threshold and Host Wake-Up Features (Rev. A) Datasheet
Product
Folder
Order
Now
Support &
Community
Tools &
Software
Technical
Documents
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
ADS7142-Q1 Automotive, 2-Channel, 12-Bit, 140-kSPS, I2C-Compatible ADC With
Programmable Threshold and Host Wake-Up Features
1 Features
•
1
•
•
•
•
•
•
•
•
2 Applications
General-purpose voltage, current and temperature
monitoring in:
• Automotive camera modules
• Driver monitoring and assistance systems
• Infotainment systems and clusters
• Electric and ICE powertrain systems
AEC-Q100 qualified for automotive applications:
– Device temperature grade 1:
–40°C to 125°C, TA
Small package size: 3 mm × 2 mm
12-bit noise-free resolution
Up to 140-kSPS sampling rate
Efficient host sleep and wake-up:
– Autonomous monitoring at 900 nW
– Windowed comparator for event-triggered host
wake-up
Independent configuration and calibration:
– Dual-channel, pseudo-differential, or groundsense input configuration
– Programmable thresholds for calibration
– Internal calibration improves offset and drift
False trigger prevention:
– Programmable thresholds per channel
– Programmable hysteresis for noise immunity
– Event counter for transient rejection
I2C interface:
– Compatible from 1.65 V to 3.6 V
– 8 configurable addresses
– Up to 3.4 MHz (high speed)
Analog supply: 1.65 V to 3.6 V
3 Description
The ADS7142-Q1 is 12-bit, 140-kSPS successiveapproximation
register
(SAR)
analog-to-digital
converter (ADC) that can autonomously monitor
signals while maximizing system power, reliability,
and performance. The device implements eventtriggered interrupts per channel using a digital
window comparator with programmable high and low
thresholds, hysteresis, and event counter. The device
includes a dual-channel analog multiplexer in front of
a SAR ADC followed by an internal data buffer for
converting and capturing data from sensors.
The ADS7142-Q1 is available in a 10-pin WSON
package and can achieve low power consumption of
only 900 nW. The small form-factor and low-power
consumption make this device suitable for spaceconstrained applications.
Device Information(1)
PART NAME
ADS7142-Q1
PACKAGE
BODY SIZE (NOM)
WSON (10)
3.00 mm × 2.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Block Diagram
AVDD
DVDD
High/Low Threshold
± Hysteresis
AINP/AIN0
Analog Input and
Multiplexer
Conversion Result
SAR-ADC
Digital
Window
Comparator
ALERT
AINM/AIN1
SCL
Offset
Calibration
Oscillator and
Timing Control
Accumulator
SDA
I2C Interface
BUSY/RDY
Data Buffer
Conversion Result [0]
«««.
«««.
«««.
GND
I2C Address
Selector
Conversion Result [15]
ADDR
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
7
1
1
1
2
3
4
Absolute Maximum Ratings ...................................... 4
ESD Ratings.............................................................. 4
Recommended Operating Conditions....................... 4
Thermal Information .................................................. 4
Electrical Characteristics: All Modes......................... 5
Electrical Characteristics: Manual Mode................... 6
Electrical Characteristics: Autonomous Modes......... 7
Electrical Characteristics: High Precision Mode ....... 8
Timing Requirements ................................................ 8
Switching Characteristics ...................................... 10
Typical Characteristics: All Modes ........................ 12
Typical Characteristics: Manual Mode .................. 13
Typical Characteristics: Autonomous Modes........ 17
Typical Characteristics: High-Precision Mode ...... 18
Detailed Description ............................................ 19
7.1
7.2
7.3
7.4
7.5
7.6
8
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
Programming...........................................................
Register Map...........................................................
19
19
20
28
39
42
Application and Implementation ........................ 59
8.1 Application Information............................................ 59
8.2 Typical Applications ................................................ 59
9
Power Supply Recommendations...................... 65
9.1 AVDD and DVDD Supply Recommendations......... 65
10 Layout................................................................... 66
10.1 Layout Guidelines ................................................. 66
10.2 Layout Example .................................................... 67
11 Device and Documentation Support ................. 68
11.1
11.2
11.3
11.4
11.5
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
68
68
68
68
68
12 Mechanical, Packaging, and Orderable
Information ........................................................... 68
4 Revision History
Changes from Original (November 2018) to Revision A
•
2
Page
Changed document status from advance information to production data.............................................................................. 1
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
5 Pin Configuration and Functions
DQC Package
10-Pin WSON
Top View
GND
1
10
AVDD
2
9
SCL
AINP/AIN0
3
8
SDA
AINM/AIN1
4
7
ALERT
ADDR
5
6
BUSY/RDY
Thermal
Pad
DVDD
Not to scale
Pin Functions
PIN
NO.
NAME
I/O
DESCRIPTION
1
GND
Supply
Ground for power supply, all analog and digital signals are referred to this pin.
2
AVDD
Supply
Analog supply input, also used as the reference voltage for analog-to-digital conversion.
3
AINP/AIN0
Analog input
Single-channel operation: positive analog signal input.
Two-channel operation: analog signal input, channel 0.
4
AINM/AIN1
Analog input
Single-channel operation: negative analog signal input.
Two-channel operation: analog signal input, channel 1.
5
ADDR
Analog Input
Input for selecting the I2C address of the device.
See the I2C Address Selection section for details.
6
BUSY/RDY
Digital output
The device pulls this pin high when scanning through channels in a sequence and brings this pin
low when the sequence is completed or aborted.
7
ALERT
Digital output
Active low, open-drain output. The status of this pin is controlled by the digital window
comparator block. Connect a pullup resistor from DVDD to this pin.
8
SDA
9
SCL
Digital input
10
DVDD
Supply
Digital input/output Serial data input/output for the I2C interface. Connect a pullup resistor from DVDD to this pin.
Serial clock for the I2C interface. Connect a pullup resistor from DVDD to this pin.
Digital I/O supply voltage.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
3
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
ADDR to GND
–0.3
AVDD + 0.3
V
AVDD to GND
–0.3
3.9
V
DVDD to GND
–0.3
3.9
V
AINP/AIN0 to GND
–0.3
AVDD + 0.3
V
AINM/AIN1 to GND
–0.3
AVDD + 0.3
Input current on any pin except supply pins
–10
10
Digital input to GND
–0.3
DVDD + 0.3
V
Junction temperature, TJ
–40
150
°C
Storage temperature, Tstg
–60
150
°C
(1)
UNIT
V
mA
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
Human-body model (HBM), per AEC Q100-002 (1)
V(ESD)
(1)
Electrostatic discharge
Charged-device model (CDM), per AEC
Q100-011
UNIT
±2000
Corner pins (1, 5, 6, and
10)
±750
All other pins
±500
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
AVDD
Analog supply voltage range
1.65
3.6
DVDD
Digital supply voltage range
1.65
3.6
V
V
TA
Ambient temperature
–40
125
°C
6.4 Thermal Information
ADS7142-Q1
THERMAL METRIC
(1)
DQC (WSON)
UNIT
10 PINS
RθJA
Junction-to-ambient thermal resistance
61.8
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
66.3
°C/W
RθJB
Junction-to-board thermal resistance
29.8
°C/W
ΨJT
Junction-to-top characterization parameter
2.1
°C/W
ΨJB
Junction-to-board characterization parameter
29.7
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
6.1
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
6.5 Electrical Characteristics: All Modes
at TA = -40°C to 125°C, AVDD = 3 V, DVDD = 1.65 V to 3.6 V, All Channel Configurations (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ANALOG INPUT (Two-Channel Single-Ended Configuration)
Full-scale input voltage
span (1)
AINP/AIN0 to GND or AINM/AIN1 to GND
0
AVDD
V
Absolute input voltage
range
AINP/AIN0 to GND or AINM/AIN1 to GND
–0.1
AVDD + 0.1
V
0
AVDD
V
AINP/AIN0 to GND
–0.1
AVDD + 0.1
AINM/AIN1 to GND
–0.1
0.1
ANALOG INPUT (Single-Channel Single-Ended Configuration with Remote Ground Sense)
Full-scale input voltage
span (1)
Absolute input voltage
range
AINP/AIN0 to AINM/AIN1
V
ANALOG INPUT (Single-Channel Pseudo-Differential Configuration with Remote Ground Sense)
Full-scale input voltage
span (1)
Absolute input voltage
range
AINP/AIN0 to AINM/AIN1
–AVDD/2
AVDD/2
AINP/AIN0 to GND
–0.1
AVDD + 0.1
AINM/AIN1 to GND
AVDD/2–0.1
AVDD/2+0.1
V
V
INTERNAL OSCILLATOR
tHSO
Time period for highspeed oscillator
tLPO
Time period for low-power
oscillator
50
110
ns
95.2
300
µs
DIGITAL INPUT/OUTPUT (SCL, SDA)
VIH
High-level input voltage
0.7 × DVDD
DVDD
V
VIL
Low-level input voltage
0
0.3 × DVDD
V
With 3 mA sink current and DVDD > 2 V
0
0.4
With 3 mA sink current and 1.65 V < DVDD <
2V
0
0.2 × DVDD
VOL = 0.4 V for standard and fast mode (100,
400 kHz)
3
VOL = 0.6 V for fast mode (400 kHz)
6
VOL = 0.4 V fast mode Plus (1 MHz)
20
VOL= 0.4 V high speed (1.7 MHz, 3.4 MHz)
25
VOL
Low-level output voltage
V
IOL
Low-level output current
(sink)
IOL
Low-level output current
(sink)
II
Input current on pin
10
µA
CI
Input capacitance on pin
10
pF
0.7 × DVDD
DVDD
V
0
0.3 × DVDD
V
mA
mA
DIGITAL OUTPUT (BUSY/RDY)
VOH
High-level output voltage
Isource = 2 mA
VOL
Low-level output voltage
Isink = 2 mA
DIGITAL OUTPUT (ALERT)
IOL
Low-level output current
VOL < 0.25 V
VOL
Low-level output voltage
Isink = 5 mA
5
mA
0
0.25
V
POWER-SUPPLY REQUIREMENTS
AVDD
Analog supply voltage
1.65
3.6
V
DVDD
Digital I/O supply voltage
1.65
3.6
V
(1)
Ideal Input span, does not include gain or offset error.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
5
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
6.6 Electrical Characteristics: Manual Mode
at TA = -40°C to 125°C, AVDD = 3 V, DVDD = 1.65 V to 3.6 V, All Channel Configurations (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SAMPLING DYNAMICS
tconv
Conversion time
AVDD = 1.65 V to 3.6 V
tacq
Acquisition time
AVDD = 1.65 V to 3.6 V
tcycle
Cycle time
AVDD = 1.65 V to 3.6 V, SCL = 3.4 MHz
1.8
18
µs
TSCL
7.1
µs
DC SPECIFICATIONS
Resolution
12
Bits
NMC
No missing codes
AVDD = 1.65 V to 3.6 V
12
Bits
DNL
Differential nonlinearity
AVDD = 1.65 V to 3.6 V
–0.99
±0.3
1
INL
Integral nonlinearity
–2.75
±0.5
2.75
LSB
EO
Offset error
Post offset calibration
–4
±0.5
4
LSB
dVOS/dT
Offset drift with temperature
Post offset calibration
EG
Gain error
–0.1
±0.03
5
Gain error drift with
temperature
LSB (1)
ppm/°C
0.1
5
%FSR
ppm/°C
AC SPECIFICATIONS
SNR
THD
(2)
Signal-to-noise ratio
(2) (3)
SINAD (2)
Total harmonic distortion
Signal-to-noise and distortion
SFDR (2)
Spurious-free dynamic range
BW
–3-dB small-signal bandwidth
fIN = 2 kHz, AVDD = 3 V,
fSAMPLE = 140 kSPS
68.75
70
dB
fIN = 2 kHz, AVDD = 1.8 V,
fSAMPLE = 140 kSPS
68
fIN = 2 kHz, AVDD = 3 V,
fSAMPLE = 140 kSPS
–85
fIN = 2 kHz, AVDD = 1.8 V,
fSAMPLE = 140 kSPS
–80
dB
fIN = 2 kHz, AVDD = 3 V,
fSAMPLE = 140 kSPS
68.5
69.5
dB
fIN = 2 kHz, AVDD = 1.8 V,
fSAMPLE = 140 kSPS
67.5
fIN = 2 kHz, AVDD = 3 V,
fSAMPLE = 140 kSPS
90
dB
25
MHz
POWER CONSUMPTION
fSAMPLE = 140 kSPS, SCL = 3.4 MHz
265
fSAMPLE= 5.5 kSPS, SCL = 100 kHz
IAVDD
IDVDD
Analog supply current
Digital supply current
300
8
fSAMPLE = 140 kSPS, SCL = 3.4 MHz, AVDD
= 1.8 V
160
fSAMPLE = 5.5 kSPS, SCL = 100 kHz, AVDD
= 1.8 V
5
fSAMPLE = 140 kSPS, SCL = 3.4 MHz, SDA =
AAA0h
25
fSAMPLE = 5.5 kSPS, SCL = 100 kHz, SDA =
AAA0h
2
fSAMPLE = 140 kSPS, SCL = 3.4 MHz, AVDD
= 1.8 V, SDA = AAA0h
15
µA
µA
IAVDD
Static analog supply current
No activity on SCL and SDA
6
nA
IDVDD
Static digital supply current
No activity on SCL and SDA
2
nA
(1)
(2)
(3)
6
LSB means least significant byte. See the ADC Transfer Function for details.
All specifications expressed in decibels (dB) refer to the full-scale input (FSR) and are tested with an input signal 0.5 dB below full-scale,
unless otherwise specified.
Calculated on the first nine harmonics of the input frequency.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
6.7 Electrical Characteristics: Autonomous Modes
at TA = -40°C to 125°C, AVDD = 3 V, DVDD = 1.65 V to 3.6 V, All Channel Configurations (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SAMPLING DYNAMICS
tconv
tacq
tcycle
Conversion time
Acquisition time
Cycle time
High-speed oscillator
14
Low-power oscillator
14
High-speed oscillator
7
Low-power oscillator
4
tHSO
tLPO
tHSO
tLPO
High-speed oscillator
nCLK
tHSO
Low-power oscillator
nCLK
tLPO
12
Bits
Post offset calibration
±0.5
LSB
±0.03
%FSR
DC SPECIFICATIONS
Resolution
EO
Offset error
EG
Gain error
POWER CONSUMPTION
IAVDD
IDVDD
Analog supply current
Digital supply current
With low-power oscillator, nCLK = 18
0.75
With low-power oscillator, AVDD = 1.8 V,
nCLK = 18
0.45
With low-power oscillator, nCLK = 250
0.5
With low-power oscillator, nCLK = 21
940
With low-power oscillator, nCLK = 18, DVDD
= 3.3 V
0.15
With low-power oscillator, DVDD = 1.8 V,
nCLK = 18
0.25
With low-power oscillator, nCLK = 250,
DVDD = 3.3 V
0.15
With high-power oscillator, nCLK = 21,
DVDD = 3.3 V
0.15
µA
µA
IAVDD
Static analog supply current
No activity on SCL and SDA
5
nA
IDVDD
Static digital supply current
No activity on SCL and SDA
0.6
nA
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
7
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
6.8 Electrical Characteristics: High Precision Mode
at TA = -40°C to 125°C, AVDD = 3 V, DVDD = 1.65 V to 3.6 V, All Channel Configurations (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DC SPECIFICATIONS
Resolution (2)
16
ENOB
Effective number of bits
With DC input of AVDD / 2 (3)
15.4
EO
Offset error
Post offset calibration
±10
EG
Gain error
Bits
LSB
±0.03
%FSR
POWER CONSUMPTION
IAVDD
IDVDD
Analog supply current
Digital supply current
With low-power oscillator, nCLK = 18
0.6
With low-power oscillator, AVDD = 1.8 V,
nCLK = 18
0.3
With low-power oscillator, nCLK = 250
0.5
With high-speed oscillator, nCLK = 21
980
With low-power oscillator, nCLK = 21, DVDD
= 3.3 V
0.2
With low-power oscillator, DVDD = 1.8 V,
nCLK = 21
µA
0.25
µA
With low-power oscillator, nCLK = 250,
DVDD = 3.3 V
0.2
With high-speed oscillator, nCLK = 21,
DVDD = 3.3 V
0.2
IAVDD
Static analog supply current
No activity on SCL and SDA
5
nA
IDVDD
Static analog supply current
No activity on SCL and SDA
0.7
nA
(1)
(2)
(3)
Sampling dynamics for high precision mode are same as for autonomous modes.
See Equation 5
For DC input, ENOB = Ln[FSR/Standard deviation of Codes]/Ln[2]. See
6.9 Timing Requirements
at TA = -40°C to 125°C, AVDD = 3 V, DVDD = 1.65 V to 3.6 V, All Channel Configurations (unless otherwise noted) (1)
PARAMETER
MIN
MAX
UNIT
100
kHz
STANDARD MODE (100 kHz)
fSCL
SCL clock frequency
0
tHD-STA
Hold time (repeated) START condition
4
µs
tLOW
Low period of SCL
4.7
µs
tHIGH
High period of SCL
4
µs
tSU-STA
Setup time for a repeated start condition
4.7
µs
0
µs
tHD-DAT
(2) (3)
Data hold time
tSU-DAT
Data setup time
250
ns
tSU-STO
Data setup time
4
µs
tBUF
Bus free time between a STOP and START
condition
4.7
µs
Cb
Capacitive load on each line
400
pF
400
kHz
FAST MODE (400 kHz)
fSCL
SCL clock frequency
tHD-STA
Hold time (repeated) START condition
0.6
µs
tLOW
Low period of SCL
1.3
µs
tHIGH
High period of SCL
0.6
µs
(1)
(2)
(3)
8
0
All values referred to VIH(min) (0.7 DVDD) and VIL(max) (0.3 DVDD).
tHD-DAT is the data hold time that is measured from the falling edge of SCL and applies to data in transmission and the acknowledge.
The maximum tHD-DAT can be 3.45 µs and 0.9 µs for standard-mode and fast-mode, but must be less than the maximum of tVD-DAT or
tVD-ACK by a transition time. This maximum must only be met if the device does not stretch the LOW period (tLOW) of the SCL signal. If
the clock is streched, the data must be valid by the setup time before being released.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Timing Requirements (continued)
at TA = -40°C to 125°C, AVDD = 3 V, DVDD = 1.65 V to 3.6 V, All Channel Configurations (unless otherwise noted)(1)
PARAMETER
MIN
tSU-STA
Setup time for a repeated start condition
tHD-DAT
Data hold time
tSU-DAT
MAX
UNIT
0.6
µs
0
µs
Data setup time
100
ns
tSU-STO
Data setup time
0.6
µs
tBUF
Bus free time between a STOP and START
condition
1.3
µs
Cb
Capacitive load on each line
400
pF
1000
kHz
FAST MODE PLUS (1000 kHz)
fSCL
SCL clock frequency
tHD-STA
Hold time (repeated) START condition
0
tLOW
tHIGH
0.26
µs
Low period of SCL
0.5
µs
High period of SCL
0.26
µs
tSU-STA
Setup time for a repeated start condition
0.26
µs
tHD-DAT
Data hold time
0
µs
tSU-DAT
Data setup time
50
ns
tSU-STO
Data setup time
0.26
µs
tBUF
Bus free time between a STOP and START
condition
0.5
µs
Cb
Capacitive load on each line
550
pF
1.7
MHz
HIGH SPEED MODE (1.7 MHz, Cb = 400 pF max)
fSCLH
SCLH clock frequency
tHD-STA
Hold time (repeated) START condition
160
0
ns
tLOW
Low period of SCL
320
ns
tHIGH
High period of SCL
120
ns
tSU-STA
Setup time for a repeated start condition
160
tHD-DAT
Data hold time
0
tSU-DAT
Data setup time
10
tSU-STO
Data setup time
160
Cb
Capacitive load on each line
ns
150
ns
ns
ns
100
pF
3.4
MHz
HIGH SPEED MODE (3.4 MHz, Cb = 100 pF max)
fSCLH
SCLH clock frequency
tHD-STA
Hold time (repeated) START condition
160
0
ns
tLOW
Low period of SCL
160
ns
tHIGH
High period of SCL
60
ns
tSU-STA
Setup time for a repeated start condition
tHD-DAT
Data hold time
0
tSU-DAT
Data setup time
10
tSU-STO
Data setup time
160
Cb
Capacitive load on each line
160
ns
70
ns
ns
100
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ns
pF
9
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
6.10 Switching Characteristics
at TA = -40°C to 125°C, AVDD = 3 V, DVDD = 1.65 V to 3.6 V, All Channel Configurations (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
STANDARD MODE (100 kHz)
trCL
Rise time of SCL
1000
ns
trDA
Rise time of SDA
1000
ns
tfCL
Fall time of SCL
300
ns
tfDA
Fall time of SDA
300
ns
tVD-DAT (2)
Data valid time
3.45
µs
tVD-ACK (2)
Data hold time
3.45
µs
FAST MODE (400 kHz)
trCL
Rise time of SCL
20
300
ns
trDA
Rise time of SDA
20
300
ns
tfCL
Fall time of SCL
20 × DVDD/3.6
300
ns
tfDA
Fall time of SDA
20 × DVDD/3.6
300
ns
tVD-DAT
Data valid time
0.9
µs
tVD-ACK
Data hold time
0.9
µs
tSP (3)
Pulse duration of spikes suppressed by the
input filter
50
ns
0
FAST MODE PLUS (1000 kHz)
trCL
Rise time of SCL
120
ns
trDA
Rise time of SDA
120
ns
tfCL
Fall time of SCL
20 × DVDD/3.6
120
ns
tfDA
Fall time of SDA
20 × DVDD/3.6
120
ns
tVD-DAT
Data valid time
0.45
µs
tVD-ACK
Data hold time
0.45
µs
tSP
Pulse duration of spikes suppressed by the
input filter
0
50
ns
HIGH SPEED MODE (1.7 MHz, Cb = 400 pF max)
trCL
Rise time of SCLH
20
80
ns
trCL1
Rise time of SCLH after a repeated start
condition and after an acknowledge bit
20
160
ns
trDA
Rise time of SDAH
20
160
ns
tfCL
Fall time of SCLH
20
80
ns
tfDA
Fall time of SDAH
20
160
ns
tSP
Pulse duration of spikes suppressed by the
input filter
0
10
ns
HIGH SPEED MODE (3.4 MHz, Cb = 100 pF max)
trCL
Rise time of SCLH
10
40
ns
trCL1
Rise time of SCLH after a repeated start
condition and after an acknowledge bit
10
80
ns
trDA
Rise time of SDAH
10
80
ns
tfCL
Fall time of SCLH
10
40
ns
tfDA
Fall time of SDAH
10
80
ns
tSP
Pulse duration of spikes suppressed by the
input filter
0
10
ns
(1)
(2)
(3)
10
All values referred to VIH(min) ( 0.7 DVDD ) and VIL(max) ( 0.3 DVDD ).
tVD-DAT = time for data signal from SCL LOW to SDA output.
Input filters on the SDA and SCL inputs suppress noise spikes of less than 50 ns.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
tf
tr
SDA
tSU-DAT
70%
«
70%
cont.
30%
30%
tHD-DAT
tVD-DAT
tf
tr
70%
SCL
tHD-STA
S
70%
70%
30%
tHIGH
30%
70%
30%
30%
«
cont.
9th clock
tLOW
1/fSCL
1st clock cycle
tBUF
. . . SDA
tSU-STA
tVD-ACK
tHD-STA
tSP
tSU-STO
70%
. . . SCL
Sr
30%
9th clock
P
S
VIL = 0.3VDD
VIH = 0.7VDD
Figure 1. Timing Diagram for Standard Mode, Fast Mode, and Fast Mode Plus
trDA
Sr
Sr
P
tfDA
0.7 x VDD
SDAH or SDA
0.3 x VDD
tHD-DAT
tSU-STO
tSU-STA
tHD-STA
tSU-DAT
0.7 x VDD
SCLH or SCL
0.3 x VDD
tFCL
trCL1
(1)
trCL1
(1)
trCL
tHIGH
tLOW
tLOW
tHIGH
= MCS current source pull-up
= Rp resistor pull-up
(1)
First rising edge of the SCLH signal after Sr and after each acknowledge bit.
Figure 2. Timing Diagram for High-Speed Mode
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
11
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
6.11 Typical Characteristics: All Modes
60
160
56
140
Time Period (Ps)
Time Period (ns)
at TA = 25°C, AVDD = 3 V, DVDD = 3.3 V, and two-channel single-ended configuration (unless otherwise noted)
52
48
44
40
-40
100
80
-7
26
59
Free-Air Temperature (qC)
92
125
60
-40
ADS7
Figure 3. High-Speed Oscillator Time Period vs Temperature
12
120
-7
26
59
Free-Air Temperature (qC)
92
125
ADS7
Figure 4. Low-Power Oscillator Time Period vs Temperature
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
6.12 Typical Characteristics: Manual Mode
at TA = 25°C, AVDD = 3 V, DVDD = 3.3 V, and two-channel single-ended configuration (unless otherwise noted)
0
0
-20
-20
-40
Amplitude (dB)
Amplitude (dB)
-40
-60
-80
-100
-120
-60
-80
-100
-120
-140
-140
-160
-160
-180
0
10000
20000
30000
fIN, Input Frequency (Hz)
40000
50000
0
10000
ADS7
SNR = 69.6 dB, THD = –84 dB, ENOB = 11.2,
fsample = 140 kSPS, SFDR = 87 dB, AVDD = 1.8 V
20000
30000
fIN, Input Frequency (Hz)
40000
50000
ADS7
SNR = 71.3 dB, THD = –87 dB, ENOB = 11.5,
fsample = 140 kSPS, SFDR = 89.3 dB, AVDD = 3 V
Figure 5. Typical FFT in Manual Mode
Figure 6. Typical FFT in Manual Mode
73
72
SNR
SINAD
71
Amplitude (dB)
Amplitude (dB)
72
71
70
69
70
SNR
SINAD
69
68
68
-40
-7
26
59
Free-Air Temperature (qC)
92
67
1.8
125
2.16
ADS7
fsample = 140 kSPS
3.24
3.6
ADS7
fsample = 140 kSPS
Figure 7. SNR and SINAD in Manual Mode vs Temperature
Figure 8. SNR and SINAD in Manual Mode vs AVDD
-82
91
-83.6
90.4
SFDR (dB)
THD (dB)
2.52
2.88
Free-Air Temperature (qC)
-85.2
-86.8
-88.4
89.8
89.2
88.6
-90
-40
-7
26
59
Free-Air Temperature (qC)
92
125
88
-40
ADS7
fsample = 140 kSPS
-7
26
59
Free-Air Temperature (qC)
92
125
ADS7
fsample = 140 kSPS
Figure 9. THD in Manual Mode vs Temperature
Figure 10. SFDR in Manual Mode vs Temperature
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
13
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Typical Characteristics: Manual Mode (continued)
at TA = 25°C, AVDD = 3 V, DVDD = 3.3 V, and two-channel single-ended configuration (unless otherwise noted)
-78
60000
Number of Hits
THD (dB)
-81
-84
-87
40000
20000
-90
3790
-93
1.8
2.16
2.52
2.88
AVDD (V)
3.24
2047
3.6
ADS7
ADS7
Figure 12. Typical DC Code Spread in Manual Mode
3
2.5
2.6
2.1
Offset Error (LSB)
Offset Error (LSB)
2049
Mean code = 2047.9, standard deviation = 0.32
Figure 11. THD in Manual Mode vs AVDD
2.2
1.8
1.4
1.7
1.3
0.9
1
-40
-7
26
59
Free-Air Temperature (qC)
92
0.5
1.8
125
2.16
ADS7
Figure 13. Offset Error in Manual Mode vs Temperature
0.07
0.03
0.052
0.01
-0.01
-0.03
2.52
2.88
AVDD (V)
3.24
3.6
ADS7
Figure 14. Offset Error in Manual Mode vs AVDD
0.05
Gain Error ( FSR)
Gain Error ( FSR)
2048
Output Code
fsample = 140 kSPS
0.034
0.016
-0.002
-0.05
-40
-7
26
59
Free-Air Temperature (qC)
92
125
-0.02
1.8
ADS7
Figure 15. Gain Error in Manual Mode vs Free-Air
Temperature
14
3046
0
2.16
2.52
2.88
AVDD (V)
3.24
3.6
ADS7
Figure 16. Gain Error in Manual Mode vs AVDD
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Typical Characteristics: Manual Mode (continued)
at TA = 25°C, AVDD = 3 V, DVDD = 3.3 V, and two-channel single-ended configuration (unless otherwise noted)
0.5
Differential Nonlinearity (LSB)
Differential Nonlinearity (LSB)
0.5
0.3
0.1
-0.1
-0.3
-0.5
0.3
0.1
-0.1
-0.3
-0.5
0
819
1638
2457
Output Code
3276
4095
0
819
ADS7
AVDD = 3 V
Figure 17. Typical DNL in Manual Mode
4095
ADS7
Figure 18. Typical DNL in Manual Mode
Integral Nonlinearity (LSB)
1
0.6
0
-0.6
-1.2
0.6
0.2
-0.2
-0.6
-1
0
819
1638
2457
Output Code
3276
4095
0
819
ADS7
AVDD = 3 V
1638
2457
Output Code
3276
4095
ADS7
AVDD = 1.8 V
Figure 19. Typical INL in Manual Mode
Figure 20. Typical INL in Manual Mode
1
1
Maximum
Minimum
Differential Nonlinearity (LSB)
Maximum
Minimum
Differential Nonlinearity (LSB)
3276
AVDD = 1.8 V
1.2
Integral Nonlinearity (LSB)
1638
2457
Output Code
0.6
0.2
-0.2
-0.6
-1
-40
-7
26
59
Free-Air Temperature (qC)
92
125
0.6
0.2
-0.2
-0.6
-1
1.8
2.16
ADS7
Figure 21. DNL in Manual Mode vs Temperature
2.52
2.88
AVDD (V)
3.24
3.6
ADS7
Figure 22. DNL in Manual Mode vs AVDD
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
15
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Typical Characteristics: Manual Mode (continued)
1
1
0.5
0.4
Integral Nonlinearity (LSB)
Integral Nonlinearity (LSB)
at TA = 25°C, AVDD = 3 V, DVDD = 3.3 V, and two-channel single-ended configuration (unless otherwise noted)
Maximum
Minimum
0
-0.5
-1
-1.5
-40
-7
26
59
Free-Air Temperature (qC)
92
Maximum
Minimum
-0.2
-0.8
-1.4
-2
1.8
125
Figure 23. INL in Manual Mode vs Temperature
2.52
2.88
AVDD (V)
3.24
3.6
ADS7
Figure 24. INL in Manual Mode vs AVDD
350
260
300
254
250
248
IAVDD (PA)
IAVDD (PA)
2.16
ADS7
200
150
242
236
100
1.8
2.16
2.52
2.88
AVDD (V)
3.24
230
-40
3.6
-7
ADS7
26
59
Free-Air Temperature (qC)
92
125
ADS7
fSample = 140 kSPS, SCL = 3.4 MHz
Figure 25. IAVDD in Manual Mode vs AVDD
Figure 26. IAVDD in Manual Mode vs Temperature
0.8
20
AVDD = 1.8 V
AVDD = 3 V
17.5
0.6
12.5
IAVDD (PA)
IDVDD (PA)
15
10
7.5
0.4
0.2
5
0
2.5
0
0
500
1000
1500
2000
SCL (kHz)
2500
3000
3500
-0.2
-40
ADS7
DVDD = 1.8 V
26
59
Free-Air Temperature (qC)
92
125
ADS7
No activity on SCL and SDA
Figure 27. IDVDD in Manual Mode vs SCL
16
-7
Figure 28. Static IAVDD in Manual Mode vs Temperature
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
6.13 Typical Characteristics: Autonomous Modes
at TA = 25°C, AVDD = 3 V, DVDD = 3.3 V, and two-channel single-ended configuration (unless otherwise noted)
8
Analog Input Current (nA)
Analog Input Current (PA)
12
9
6
3
0
6.4
4.8
3.2
1.6
0
0
45
90
135
nCLK
180
225
270
0
45
90
ADS7
Input voltage = 1.5 V, CH0, high-speed oscillator, stop burst mode
135
nCLK
180
270
AINC
Input voltage = 1.5 V, CH0, low-power oscillator, stop burst mode
Figure 29. Analog Input Current in Autonomous Modes vs
nCLK
Figure 30. Analog Input Current in Autonomous Modes vs
nCLK
1500
1500
AVDD = 1.8 V
AVDD = 3 V
AVDD = 1.8 V
AVDD = 3 V
1200
1200
900
900
IAVDD (PA)
IAVDD (nA)
225
600
300
0
-40
600
300
-7
26
59
Free-Air Temperature (qC)
92
125
0
-40
ADS7
Stop burst mode, low-power oscillator, nCLK = 25
Figure 31. IAVDD in Autonomous Modes vs Temperature
-7
26
59
Free-Air Temperature (qC)
92
125
Auto
Stop burst mode, high-speed oscillator, nCLK = 25
Figure 32. IAVDD in Autonomous Modes vs Temperature
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
17
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
6.14 Typical Characteristics: High-Precision Mode
at TA = 25°C, AVDD = 3 V, DVDD = 3.3 V, and two-channel single-ended configuration (unless otherwise noted)
10
0.03
0.018
Gain Error ( FSR)
Offset Error (LSB)
7
4
0.006
-0.006
1
-0.018
-2
-40
-7
26
59
Free-Air Temperature (qC)
92
-0.03
-40
125
-7
Offs
Figure 33. Offset Error in High-Precision Mode vs
Temperature
26
59
Free-Air Temperature(qC)
AVDD = 1.8 V
AVDD = 3 V
900
900
IAVDD (PA)
IAVDD (nA)
Gain
1200
AVDD = 1.8 V
AVDD = 3 V
600
300
600
300
-7
26
59
Free-Air Temperature (qC)
92
125
0
-40
ADS7
Low-power oscillator, nCLK = 25
-7
26
59
Free-Air Temperature (qC)
92
125
IAVD
High-speed oscillator, nCLK = 25
Figure 35. IAVDD in High-Precision Mode vs Temperature
18
125
Figure 34. Gain Error in High-Precision Mode vs
Temperature
1200
0
-40
92
Figure 36. IAVDD in High-Precision Mode vs Temperature
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
7 Detailed Description
7.1 Overview
The ADS7142-Q1 is a small size, dual-channel, 12-bit programmable sensor monitor with an integrated analogto-digital converter (ADC), input multiplexer, digital comparator, data buffer, accumulator and internal oscillator.
The input multiplexer can be either configured as two single-ended channels, one single-ended channel with
remote ground sensing, or one pseudo-differential channel where the input can swing to approximately AVDD /
2. The device includes a digital window comparator with a dedicated output pin, which can be used to alert the
host when a programmed high or low threshold is crossed. The device address is configured by the I2C address
selector block. The device uses internal oscillators (high speed or low power) for conversion. The start of
conversion is controlled by the host in manual mode and by the device in the autonomous modes.
The device also features a data buffer and an accumulator. The data buffer can store up to 16 conversion results
of the ADC in the autonomous modes and the accumulator can accumulate up to 16 conversion results of the
ADC in high-precision mode.
The device includes an offset calibration to calibration its own offset.
7.2 Functional Block Diagram
AVDD
DVDD
High/Low Threshold
± Hysteresis
AINP/AIN0
Analog Input and
Multiplexer
Conversion Result
SAR-ADC
Digital
Window
Comparator
ALERT
AINM/AIN1
SCL
Offset
Calibration
Oscillator and
Timing Control
Accumulator
SDA
I2C Interface
BUSY/RDY
Data Buffer
Conversion Result [0]
«««.
«««.
«««.
GND
I2C Address
Selector
Conversion Result [15]
ADDR
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
19
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
7.3 Feature Description
7.3.1 Analog Input and Multiplexer
Figure 37 shows a small-signal equivalent circuit for the analog input pins. The device includes a two-channel
analog multiplexer with each input pin having ESD protection diodes to AVDD and GND. The sampling switches
are represented by ideal switches SW1 and SW2 in series with resistors Rs1 and Rs2 (typically 150 Ω). The
sampling capacitors, Cs1 and Cs2, are typically 15 pF. The multiplexer configuration is set by the
CH_INPUT_CFG register.
During acquisition, switches SW1 and SW2 are closed to allow the input signal to charge the internal sampling
capacitors.
During conversion, switches SW1 and SW2 are opened to disconnect the input signal from the sampling
capacitors.
The analog input of the device are optimized to be driven by high impedance source (up-to 100 kΩ) in
Autonomous Modes or in High Precision Mode mode with low power oscillator. It is recommended to drive the
analog input of the device with an external amplifier when in Autonomous Modes or in High Precision Mode
mode with a high-speed oscillator. Figure 29 and Figure 30 provide the analog input current for CH0 and CH1 of
the device.
Figure 38, Figure 39 and Figure 40 provide a simplified circuit for analog input for input configurations described
in Two-Channel, Single-Ended Configuration, Single-Channel, Single-Ended Configuration and Single-Channel,
Pseudo-Differential Configuration respectively. The analog multiplexer supports following input configurations (set
by writing into the CH_INPUT_CFG register).
AVDD
AVDD
CH0
SW1
AINP/AIN0
AINP/AIN0
SW1
CH0
CH1
Rs1
GND
Rs1
Cs1
Cs1
AVDD
AVDD
MUX
CH1
Cs2
SW2
AINM/AIN1
V_BIAS
Cs2
MUX
V_BIAS
SW2
AINM/AIN1
Rs2
Rs2
GND
GND
GND
CHANNEL_INPUT_CFG_REG
CHANNEL_INPUT_CFG_REG
Figure 38. Two-Channel, Single-Ended Configuration
Figure 37. Equivalent Circuit for Analog Input
AVDD
AVDD
SW1
AINP/AIN0
Cs1
GND
MUX
SW2
Rs2
Rs1
Cs1
GND
MUX
V_BIAS
Cs2
AVDD/2 + 100mV
Cs2
AINM/AIN1
SW1
AINP/AIN0
V_BIAS
GND + 100mV
GND
AVDD/2
Rs1
AVDD/2
SW2
AINM/AIN1
Rs2
AVDD/2-100mV
GND -100mV
GND
GND
CHANNEL_INPUT_CFG_REG
CHANNEL_INPUT_CFG_REG
Figure 39. Single-Channel, Single-Ended Configuration
With Remote Ground Sensing
Figure 40. Single-Channel, Pseudo-Differential
Configuration
7.3.1.1 Two-Channel, Single-Ended Configuration
Figure 38 shows a simplified block diagram showing a two-channel, single-ended configuration. Set the
CH0_CH1_IP_CFG bits = 00b or 11b to select this configuration. This configuration is also the default for the
device after power up. In this configuration, CS2 always samples the GND pin and CS1 samples the input signal
provided on channel 0 (AINP/AIN0) or channel 1 (AINM/AIN1) based on the channel selection. Each analog input
channel can accept input signals in the range 0 V to AVDD V.
20
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Feature Description (continued)
On power-up, the device wakes up in manual mode with two-channel, single-ended configuration and samples
CH0 only. This configuration can also be set by setting OPMODE_SEL to 000b or 001b,
The device can be configured to sample either CH0 or CH1 or both channels by setting bits in the
AUTO_SEQ_CHEN register to select the channels.
•
•
•
•
To select a channel in AUTO sequence, set AUTO_SEQ_CHx bit in the AUTO_SEQ_CHEN register to 1.
Set the bits in the OPMODE_SEL register to 100b or 101b for manual mode with AUTO sequence.
Set the bits in the OPMODE_SEL register to 110b for Autonomous Modes with AUTO sequence.
Set the bits in the OPMODE_SEL register to 111b for High Precision Mode with AUTO sequence.
7.3.1.2
Single-Channel, Single-Ended Configuration
See Figure 39 for a simplified block diagram showing a single-channel, single ended configuration. Set
CH0_CH1_IP_CFG bits = 01b to select this configuration. In this configuration, CS1 samples the input signal
provided on the AINP/AIN0 pin whereas CS2 samples input signal provided on the AINM/AIN1 pin. AINP/AIN0 pin
can accept input signals in the range 0 V to AVDD V and AINM/AIN1 pin can accept input signals in the range
–100 mV to +100 mV. This input configuration is useful in systems where the sensor and/or the signal
conditioning block is placed far from the device and there could be a small difference between the ground
potentials. In this channel configuration, remove channel 1 from AUTO sequence by setting the
AUTO_SEQ_CH1 bit to 0. Selecting channel 1 in AUTO sequence leads to an error condition and the device
sets an error flag in the SEQUENCE_STATUS register.
7.3.1.3 Single-Channel, Pseudo-Differential Configuration
See Figure 40 for a simplified block diagram showing a single-channel, pseudo-differential configuration. Set
CH0_CH1_IP_CFG bits = 10b to select this configuration. In this configuration, CS1 samples the input signal
provided on the AINP/AIN0 pin whereas CS2 samples input signal provided on the AINM/AIN1 pin. AINP/AIN0 pin
can accept input signals in the range 0 V to AVDD V and AINM/AIN1 pin can accept input signals in the range
(AVDD/2) - 100 mV to (AVDD/2) + 100 mV. This input configuration is useful to interface with sensors that
provide pseudo-differential signal with negative output as AVDD/2 like an electrochemical gas sensor. In this
channel configuration, remove channel 1 from AUTO sequence by setting the AUTO_SEQ_CH1 bit to 0.
Selecting channel 1 in AUTO sequence leads to an error condition and the device sets an error flag in
SEQUENCE_STATUS register.
7.3.2 OFFSET Calibration
The offset can be calibrated by setting the TRIG_OFFCAL bit in the OFFSET_CAL register. During offset
calibration, the sampling switches are open (Figure 37) and the device keeps BUSY/RDY pin high. The device
calculates its offset error and corrects for this error for subsequent conversions. The device calibrates the offset
on power up. To nullify the change in offset due to change in temperature or in AVDD voltage, it is recommended
to perform this calibration periodically.
7.3.3 Reference
The device uses the analog supply voltage (AVDD) as a reference for the analog-to-digital conversion process. It
is recommended to place a 220-nF, low-ESR ceramic decoupling capacitor between the AVDD pin and the GND
pin, close to the AVDD Pin. See Power Supply Recommendations section.
7.3.4 ADC Transfer Function
The ADC provides data in straight binary format. The ADC resolution can be computed by Equation 1:
1 LSB = VREF / 2N
where:
•
•
VREF = AVDD
N = 12 for Autonomous Monitoring Modes and Manual Mode
(1)
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
21
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Feature Description (continued)
Figure 41 and Figure 42 show the ideal transfer characteristics for single-ended input and pseudo-differential
input, respectively. Table 1 show the digital output codes for the transfer functions.
PFSC
ADC Code (Hex)
ADC Code (Hex)
PFSC
MC + 1
MC
MC + 1
MC
NFSC+1
NFSC
1 LSB
VREF/2
(VREF/2 + 1 LSB)
VIN
(VREF ± 1 LSB)
NFSC+1
NFSC
Figure 41. Ideal Transfer Characteristics for
Single-Ended Configurations
(-VREF/2 + 1 LSB)
0
1 LSB
VIN
(VREF/2 ± 1 LSB)
Figure 42. Ideal Transfer Characteristics for
Pseudo-Differential Configuration
Table 1. Transfer Characteristics
INPUT VOLTAGE FOR SINGLE-ENDED INPUT
INPUT VOLTAGE FOR PSEUDO
DIFFERENTIAL INPUT
CODE
DESCRIPTION
IDEAL
OUTPUT
CODE
(Autonomous
Monitoring
Mode or
Manual Mode)
≤1 LSB
≤ (–VREF / 2 + 1) LSB
NFSC
Negative full-scale
code
000
1 LSB to 2 LSBs
(–VREF / 2 + 1) to (–VREF / 2 + 2) LSB
NFSC + 1
—
001
(VREF / 2) to (VREF / 2) + 1 LSB
0 LSB to 1 LSB
MC
Mid code
800
(VREF / 2) + 1 LSB to (VREF / 2) + 2 LSBs
1 LSB to 2 LSB
MC + 1
—
801
≥ VREF – 1 LSB
≥ VREF / 2 – 1 LSB
PFSC
Positive full-scale code
FFF
7.3.5 Oscillator and Timing Control
The device uses one of the two internal oscillators (low power oscillator or high speed oscillator) for converting
the analog input voltage into a digital output code.
The steps for selecting the oscillator and setting the sampling speed are listed below:
1. Select the low power oscillator (OSC_SEL = 1b) to monitor slow moving signals (< 300 Hz) at extremely low
power consumption and sampling speeds (< 600 SPS). Select the high speed oscillator (OSC_SEL = 0b) to
scan the sensor signals with faster sampling speed (> 50 kHz).
2. Set sampling speed by programming the NCLK_SEL register:
Oscillator frequency
nCLK
fS
•
•
•
22
fs = Sampling speed
Oscillator frequency = 1 / tHSO or 1 / tLPO depending on the OSC_SEL bit; see the Specifications section for
1 / tHSO or 1 / tLPO
nCLK is number of clocks in one conversion cycle (see the NCLK_SEL register)
(2)
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
7.3.6 I2C Address Selector
The I2C address for the device is determined by connecting external resistors on ADDR pin. The device address
are selected on power-up based on the resistor values. The device retains this address until the next power up,
or until next device reset, or until the device receives a command to program its own address (General Call With
Write Software Programmable Part of Slave Address). Figure 43 provides the connection diagram for the ADDR
pin and Table 2 provides the resistor values for selecting different addresses of the device.
AVDD
R1
ADDR
R2
Copyright © 2017, Texas Instruments Incorporated
Figure 43. External Resistor Connection Diagram for ADDR Pin
Table 2. I2C Address Selection
RESISTORS
R1
(1)
ADDRESS
0Ω
DNP (2)
0011111b (1Fh)
11 kΩ
DNP (2)
0011110b (1Eh)
33 kΩ
DNP (2)
0011101b (1Dh)
(2)
0011100b (1Ch)
100 kΩ
DNP
DNP (2)
0Ω or DNP (2)
0011000b (18h)
DNP (2)
11 kΩ
0011001b (19h)
33 kΩ
0011010b (1Ah)
100 kΩ
0011011b (1Bh)
DNP
(2)
DNP (2)
(1)
(2)
R2 (1)
Tolerance for R1, R2 < ±5%.
DNP = Do not populate.
7.3.7 Data Buffer
When operating in autonomous monitoring mode, the device can use the internal data buffer for data storage.
The internal data buffer is 16-bit wide and 16-word deep and follows the first-in, first-out (FIFO) approach.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
23
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
7.3.7.1 Filling of the Data Buffer
The write operation to the data buffer starts and stops as per the settings in the DATA_BUFFER_OPMODE
register. The DATA_BUFFER_STATUS register provides the number of entries filled in the data buffer and this
register can be read during an active sequence to get the current status of the data buffer.
The time between two consecutive conversions is set by the NCLK_SEL register and Equation 3 provides the
relationship for time between two consecutive conversions of the same channel and nCLK parameter.
tcc = k x nCLK x OscillatorTimePeriod
where
•
•
•
•
tcc = Time between two consecutive conversions of same channel, tcc = k × tcycle
k = Number of channels enabled in the device sequence
nCLK = Number of clocks used by device for one conversion cycle
Oscillator timer period = tLPO or tHSO depending on the OSC_SEL value; see the Specifications section for tLPO
or tHSO
(3)
The format of the 16-bit contents of each entry in the data buffer are set by programming the
DOUT_FORMAT_CFG register. The DATA_OUT_CFG register enables the channel ID and DATA_VALID flag in
data buffer. Channel ID represents the channel number for the data entry in the data buffer. DATA_VALID is set
to zero in either of the following conditions:
•
•
If the entry in the data buffer is not filled after the last start of sequence.
If the I2C master tries to read more than 16 entries from the data buffer, the device provides zeros with
DATA_VALID set to zero
At the end of the write operation, the data buffer always has results of 16 (or lesser) consecutive conversions.
The data buffer is filled in the order that the data is converted by the ADC. The channels converted by the ADC
are controlled by the AUTO_SEQ_CHEN register. The entries that are not filled during an active sequence are
filled with zeros.
7.3.7.2 Reading Data From the Data Buffer
The device brings the BUSY/RDY pin low after completion of the sequence or after the SEQ_ABORT bit is set.
As illustrated in Figure 44, the device provides the contents of the data buffer (in FIFO fashion) on receiving I2C
read frame, which consists of the device address and the read bit set to 1.
S
Device Address (7 Bits)
R
A
MSB for Data Buffer Entry 0
A
LSB for Data Buffer Entry 0
A
MSB for Data Buffer Entry 1
A
LSB for Data Buffer Entry 15
N
P/Sr
Data from Host to Device
Data from Device to Host
Figure 44. Reading Data Buffer (16 Bit Words × 16 Words)
The device returns zeroes with DATA VALID flag set to zero for all I2C read frames received after all the valid
data words from the data buffer are read or when a I2C read frame is issued during an active sequence
(indicated by high on the BUSY/RDY pin). The I2C master needs to provide a NACK followed by a STOP or
RESTART condition in an I2C frame to finish the reading process. The data buffer is reset by setting the
SEQ_START bit or after resetting the device.
24
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
7.3.8 Accumulator
When operating in High Precision Mode, the device offers a 16-bit internal accumulator per channel. The
Accumulator for a channel is enabled only if that channel is selected in the channel scanning sequence. The
accumulator adds sixteen 12-bit conversion results. The result of adding 16 twelve bit words is one 16 bit word
that has an effective resolution of an 16-bit ADC. The time between two consecutive conversions for
accumulation is controlled by the NCLK_SEL register and Equation 3 provides the relationship for time between
two consecutive conversions of same channel and nCLK parameter.
The accumulated data can be read from the ACC_CHx_MSB and ACC_CHx_LSB registers in the device. The
ACCUMULATOR_STATUS register provides the number of accumulations done in the accumulator since last
conversion. This register can be read during an active sequence to get the current status of the accumulator.
The accumulator is reset on setting the SEQ_START bit and on resetting the device.
Equation 4 provides the relationship between high precision data and ADC conversion results.
16
High Precision Data for CHx
¦ Conversion Result[k]
for CHx
(4)
k 1
Equation 5 provides the value of LSB in high precision mode for the accumulated result.
AVDD
1 LSB
216
(5)
7.3.9 Digital Window Comparator
The internal digital window comparator is available in all modes. In Autonomous Modes with Thresholds
monitoring and Diagnostics, the digital window comparator controls the filling of the data and the output of the
alert pin and in other modes, it only controls the output of the ALERT pin. Figure 45 provides the block diagram
for digital window comparator.
DWC_BLOCK_EN
ALERT_EN_CH1
Channel 1
ALERT_EN_CH0
Channel 0
(High Side Threshold, Hysteresis)
for CH0
ADC
Conversion Result for CH0
(Low Side Threshold, Hysteresis)
for CH0
High Side Comparator
High Side
Counter
End of
Conversion
S
Q
High Latched Flag for CH0
R
Write Bit to
Reset
Low Side
Counter
OR
OR
ALERT
R
Q
Low Latched Flag for CH0
S
Low Side Comaparator
Figure 45. Digital Comparator Block Diagram
The low side threshold, high side threshold, and hysteresis parameters are independently programmable for
each input channel. Figure 46 shows the comparison thresholds and hysteresis for the two comparators. A prealert event counter after each comparator counts the output of the comparator and sets the latched flags. The
pre-alert event counter settings are common to the two channels.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
25
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
NOTE: PRE_ALT_MAX_EVENT_COUNT = 70h
(waits for 8 counts to set alert)
2
High Threshold
1
3
1
5
High Threshold - Hysteresis
8
2
4
7
3
4 5
6
6
Counter Reset because the high-side-comparator reset
before 8.
Counter Reset because the high-side-comparator reset
before 8.
Low Threshold + Hysteresis
7
4
Low Threshold
5
6
3
1
2
High Side Comparator
(Internal Only Signal)
Low Side Comparator
(Internal Only Signal)
ALERT
Figure 46. Thresholds, Hysteresis and Event Counter for Digital Window Comparator
The DWC_BLOCK_EN bit in ALERT_DWC_EN register enables/disables the complete digital window
comparator block (disabled at power-up) and ALERT_EN_CHx bits in the ALERT_CHEN register enables digital
window comparator for individual channels. When enabled, whenever a new conversion result is available:
1. The output of the high side comparator transitions to logic high when the conversion result is greater than the
high threshold. This comparator resets when the conversion result is less than the high threshold –
hysteresis.
26
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
2. The output of the low side comparator transitions to logic high when the conversion result is less than the low
threshold. This comparator resets when the conversion result is greater than the low threshold + hysteresis.
3. A different threshold and hysteresis can be used for each channel.
4. When the output of either the high side or low side comparator transitions high the pre-alert event counter
begins to increment for each subsequent conversion. This counter continues to increment until it reaches the
value
stored
in
the
PRE_ALT_MAX_EVENT_COUNT
register.
When
it
reaches
PRE_ALT_MAX_EVENT_COUNT, the alert becomes active and sets the latched flags. If the comparator
output becomes zero before counter reaches PRE_ALT_MAX_EVENT_COUNT, then the event counter is
reset to zero, Alert does not be set and latched flag is not set.
Therefore, the latched flags (high and low) for the channel are updated only if the respective comparator output
remains 1 for the specified number of consecutive conversions (set by PRE_ALT_MAX_EVENT_COUNT).
The latched flags can be read from the ALERT_LOW_FLAGS and ALERT_HIGH_FLAGS registers. To clear a
latched flag, write 1 to the applicable bit location. The ALERT pin status is re-evaluated whenever an applicable
latched flag gets set or is cleared.
The response time for ALERT pin can be estimated by Equation 6
tresponse = [1 + k x (PRE_ALT_MAX_EVENT_COUNT + 1) ] x nCLK x Oscillator TimePeriod
where
•
•
•
k = Number of channels enabled in device sequence
nCLK = Number of clocks used by device for one conversion cycle
Oscillator timer period = tLPO or tHSO depending on the OSC_SEL value; see the Specifications section for tLPO
or tHSO
(6)
7.3.10 I2C Protocol Features
7.3.10.1 General Call
On receiving a general call (00h), the device provides an ACK.
7.3.10.2 General Call With Software Reset
On receiving a general call (00h) followed with Software Reset (06h), the device resets itself.
7.3.10.3 General Call With Write Software Programmable Part of Slave Address
On receiving a general call (00h) followed by 04h, the device configures its own I2C address configured by the
ADDR pin. During this operation, the device keeps BUSY/RDY Pin high and does not respond to other I2C
commands except general call.
7.3.10.4 Configuring the Device Into High-Speed I2C Mode
The device can be configured in high-speed I2C mode by providing an I2C frame with one of the HS-mode
master codes (08h to 0Fh).
After receiving one of the HS-mode master codes, the device sets the HS_MODE bit in the
OPMODE_I2CMODE_STATUS register and remains in high-speed I2C mode until a STOP condition is received
in an I2C frame.
7.3.10.5 Bus Clear
If the SDA line is stuck low because of an incomplete I2C frame, providing nine clocks on SCL is recommended.
The device releases the SDA line within these nine clocks, and then the next I2C frame can be started.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
27
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
7.4 Device Functional Modes
The device has below functional modes:
• Manual mode
• Autonomous modes:
– Autonomous mode with threshold monitoring and diagnostics
– Autonomous mode with burst data
• High-precision mode
Device powers up in manual mode and can be configured into one of the other modes of these modes by writing
the configuration registers for the desired mode. Steps for configuring device into different modes are illustrated
in Figure 47
Device Power Up or
Reset
OFFSET Calibration
on Power Up(1)
Select the Channel
Input
Configurations(2)
Select the Operation
Mode of the device(3)
Set the I2C Mode to
High Speed
(Optional)(4)
Manual Mode(5)
Autonomous Modes(5)
High Precision
Mode(5)
(1)
Offset can also be calibrated anytime during normal operation by setting the bit in the OFFSET_CAL register.
(2)
Configure the CH_INPUT_CFG register.
(3)
Configure the OPMODE_SEL register for the desired operation mode.
(4)
See the Configuring the Device Into High-Speed I2C Mode section.
(5)
Operating mode is selected by configuring the OPMODE_SEL register in step 3.
(6)
For reading and writing registers, see the Programming section.
Figure 47. Configuring Device Into Different Modes
7.4.1 Device Power Up and Reset
On power up, the device calibrates its own offset and calculates the address from the resistors connected on
ADDR pin. During this time, the device keeps BUSY/RDY high.
The device can be reset by recycling power on AVDD pin, by general call (00h) followed by software reset (06h),
or by writing the WKEY register followed by setting the bit in the DEVICE_RESET register.
Recycling power on the AVDD pin and on general call (00h) followed by software reset (06h), all the device
configurations are reset, and the device initiates offset calibration and re-evaluates its I2C address.
When setting the bit in DEVICE_RESET register, all the device configurations except latched flags for the digital
window comparator and the WKEY register are reset, The device does not initiate offset calibration and does not
re-evaluate its I2C address.
28
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Device Functional Modes (continued)
7.4.2 Manual Mode
On power-up, the device is in Manual Mode using the single ended and dual channel configuration and starts by
sampling the analog input applied on channel 0. In this mode, the device uses the high frequency oscillator for
conversions. Manual mode allows the external host processor to directly request and control when the data is
sampled. The data capture is initiated by an I2C command from the host processor and the data is then returned
over the I2C bus at a throughput rate of up to 140-kSPS. Applications that can take advantage of this type of
functionality include traditional ADC applications that require 1 or 2 channels of continuous data output.
After setting the operation mode to manual mode as illustrated in Figure 47, steps for operating the device to be
in manual mode and reading data are illustrated in Figure 48. The host can either configure the device to scan
through one channel or both channels by configuring the CH_INPUT_CFG register and AUTO_SEQ_CHEN
register.
7.4.2.1 Manual Mode With CH0 Only
Set the OPMODE_SEL register to 000b or 001b for manual mode with channel 0 only. The host must provide the
device address and read bit to start the conversions. To continue with conversions and reading data to the host
must provide continuous SCL (Figure 49). In this mode, a NACK followed by a STOP condition in I2C frame is
required to abort the operation. Then the device operation mode can be changed to another operation mode.
7.4.2.2 Manual Mode With AUTO Sequence
Set the OPMODE_SEL register to 100b or 101b for manual mode with AUTO Sequence. The host must set the
SEQ_START bit in the START_SEQUENCE register and provide the device address and read bit to start the
conversions. To continue with conversions and reading data, the host must provide continuous SCL (Figure 49).
In this mode, the SEQ_ABORT bit in the ABORT_SEQUENCE register must be set to abort the operation. Then
the device operation mode can be changed to another operation mode. In this mode, a register read aborts the
AUTO sequence.
In manual mode, the device always uses the high-speed oscillator and the nCLK parameter has no effect. The
maximum scan rate is given by Equation 7:
1000
fS
>18 u TSCL k @
•
•
•
•
fs = Maximum sampling speed in kSPS
TSCL= Time period of SCL clock (in µs)
if TSCL-LOW (Low period of SCL) < 1.8.µs, k = (1.8 - TSCL-LOW) and the device stretches clock in manual mode;
not applicable for standard I2C mode (100 kHz)
if TSCL-LOW (low period of SCL) ≥ 1.8.µsec, k = 0 and the device does not stretch clock in manual mode
(7)
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
29
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Device Functional Modes (continued)
Manual Mode(1)
AUTO
Sequence
Scan CH0
Only
CH0 Only (Default)
No
Select Manual Mode
with AUTO Sequence
and Select Channels
in AUTO Sequence(2)
Yes
Set SEQ_START Bit(3)
Provide Device Address
and Read Bit to Start
Conversions(4)
Provide Device Address
and Read Bit to Start
Conversions(4)
Provide Continuous
SCL to the device(4)
Provide Continuous
SCL to the device(4)
Yes
Yes
Continue with
conversions and
reading data
Continue with
conversions and
reading data
No
Provide STOP
Condition on I2C Bus(4)
No
No
Set SEQ_ABORT Bit(5)
Yes
Continue in
same Operation
Mode
Yes
Continue in
same Operation
Mode
No
No
Exit to another Operation Mode(6)
(1)
For setting the operation mode to manual mode, see Figure 47.
(2)
Select manual mode with AUTO sequence in OPMODE_SEL register. Select channels in the AUTO_SEQ_CHEN
register.
(3)
Set the bit SEQ_START bit in the START_SEQUENCE register.
(4)
See Figure 49.
(5)
Set the bit SEQ_ABORT bit in the ABORT_SEQUENCE register.
(6)
Select another operation mode in the OPMODE_SEL register.
(7)
For reading and writing registers, see the Programming section.
Figure 48. Device Operation in Manual Mode
30
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Device Functional Modes (continued)
Data can be read from the device by providing a device address and read bit followed by continuous SCL as
shown in Figure 49.
Sample A
Sample A+1
Device I2C Address from Host
SDA
SCL
S
ADC Data for Sample A
A6
A5
A4
A3
A2
A1
A0
R
ACK
1
2
3
4
5
6
7
8
9
Device in Acquisition
ADC Data for Sample A
D11
D10
D9
D8
D7
D6
D5
1
2
3
4
5
6
7
Optional
Clock
Stretch
Sample A+2
ADC Data for Sample A+1
D4
ACK
D3
D2
D1
D0
0
0
0
8
9
10
11
12
13
14
15
16
Device in Acquisition
0
ACK
D11
D10
0
NA
CK
17
18
1
2
17
18
Optional
Clock
Stretch
Device in Acquisition
Data from Host to Device
Data from Device to Host
(1)
See Equation 7 for sampling speed in manual mode.
(2)
If the device scans both channels in AUTO sequence, first data (for sample A) is from channel 0 and second data (for
sample A +1) is from channel 1.
Figure 49. Starting Conversion and Reading Data in Manual Mode
7.4.3 Autonomous Modes
In autonomous mode, the device can be programmed to monitor the voltage applied on the analog input pins of
the device and generate a signal on the ALERT pin when the programmable high or low threshold values are
crossed and store the conversion results in the data buffer before or after the crossing a threshold or before
setting the SEQ_ABORT bit (start burst) in the ABORT_SEQUENCE register or after setting the
START_SEQUENCE bit in the START_SEQUENCE register.
In autonomous mode, the device generates the start of conversion using the internal oscillator. The first start of
conversion must be provided by the host and the device generates the subsequent start of conversions.
After configuring the operation mode to autonomous mode (set the OPMODE_SEL register to 110b) as
illustrated in Figure 47, steps for operating the device to be in different autonomous modes are illustrated in
Figure 50.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
31
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Device Functional Modes (continued)
Autonomous Modes(1)
Select the Channels in AUTO
Sequence(2)
Select the Oscillator
& Set the nCLK value(3)
Select the Data Buffer Configuration(4)
Autonomous Mode with Threshold Monitoring and Diagnostics
Autonomous Mode with Burst Data
Stop Burst
Pre Alert
Post Alert
Start Burst
Set the
Thresholds,
Hysteresis and
Enable Alert(5)
Set the
Thresholds,
Hysteresis and
Enable Alert(5)
Set the
SEQ_START Bit(6)
Set the SEQ_Start
Bit(6)
Set the
SEQ_START Bit(6)
Set the
SEQ_START Bit(6)
Device Starts
conversions and
starts Filling Data
Buffer
Device Starts
Conversions
Device Starts
conversions and
starts Filling Data
Buffer
Device Starts
conversions and
starts Filling Data
Buffer
No
No
Yes
Is Alert Set?
Is Alert Set or
SEQ_ABORT bit
set ?
No
Is Data Buffer
Filled or
SEQ_ABORT
bit Set?
No
Yes
Is
SEQ_ABORT
Bit Set ?
Device Starts
Filling Data Buffer
Yes
Yes
Yes
Is Data Buffer
Filled or
SEQ_ABORT
bit Set?
No
Device Stops
Conversions &
Stops Filling Data
Buffers
Yes
Device Stops
Conversions &
Stops Filling Data
Buffers
Read the latched
flags of Digital
Window
Comparator(7)
Read the latched
flags of Digital
Window
Comparator(7)
Reset the latched
flags by writing 1(8)
Reset the latched
flags by writing 1(8)
Device Stops
Conversions &
Stops Filling Data
Buffer
Device Stops
Conversions &
Stops Filling Data
Buffer
Read the Data Buffer(9)
Continue in
same operation
mode
No
Exit to another
Operation Mode(10)
Yes
Set the
SEQ_START Bit(6)
(1)
For setting the operation mode to Autonomous modes, see Figure 47.
(2)
Select channels in the AUTO_SEQ_CHEN register.
(3)
Select the oscillator by configuring the OSC_SEL register and configure the NCLK_SEL register.
(4)
Select the data buffer mode in the DATA_BUFFER_OPMODE register.
(5)
Configure the thresholds in the DWC_xTH_CHx_xxx registers and hysteresis in the DWC_HYS_CHx registers.
Enable the alert for channels in the ALERT_CHEN register and set the DWC_BLOCK_EN bit in the
ALERT_DWC_EN register.
(6)
Set the bit SEQ_START bit in the START_SEQUENCE register.
(7)
Read the ALERT_LOW_FLAGS and/or ALERT_HIGH_FLAGS registers.
(8)
Reset the ALERT_LOW_FLAGS and/or ALERT_HIGH_FLAGS registers by writing 03h.
(9)
See the Reading Data From the Data Buffer section.
(10) Select another operation mode in the OPMODE_SEL register.
(11) For reading and writing registers, see the Programming section.
Figure 50. Configuring Device in Autonomous Modes
32
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Device Functional Modes (continued)
TI recommends aborting the present sequence by setting the SEQ_ABORT bit in the ABORT_SEQUENCE
register before changing the device operation mode or device configuration.
7.4.3.1 Autonomous Mode With Threshold Monitoring and Diagnostics
The threshold monitoring mode automatically scans the input voltage on the input channels and generates a
signal when the programmable high or low threshold values are crossed. This mode is useful for applications
where the output of the sensor must be continuously monitored and action only taken when the sensor output
deviates outside of an acceptable range. Applications that could take advantage of this type of functionality
include wireless sensor nodes, environmental sensors, smoke and heat detectors, motion detectors, and so on.
In this mode, the data buffer can be configured to store the conversion results of the ADC in two different ways.
7.4.3.1.1
Autonomous Mode With Pre Alert Data
In this mode, the device stores the sixteen conversion prior to the activation of the alert. Upon activation of
ALERT, conversion stops. For this mode, set DATA_BUFFER_OPMODE to 100b. In this mode, the device starts
converting and stores the data on setting the SEQ_START bit in the START_SEQUENCE register and continues
to store the data into the data buffer until one of the digital comparator flags is set for crossing a high threshold or
a low threshold for the channels selected in the sequence. If the SEQ_ABORT bit is set before the data buffer is
filled, the device aborts the sequence and stops storing the conversion results. If more than 16 conversions occur
between start of sequence and alert output, the first entries written into the data buffer are over-written.
Device stops conversions and Sets the Latched
flag and alert pin after count(=4) is reached
Conversion [N+ 15] for CHx
High Threshold
Sets the Output of the Comparator
Hysteresis
ADC Conversion Result
ADC Conversion Result
Figure 51 and Figure 52 show the filling of data buffer in autonomous mode with Pre alert Data.
Device stops conversions and
stops storing data in the buffer
after the count is reached
Conversion [N+ 15] for CHy
High Threshold - Hysteresis
Sets the Output of the
Comparator
Data Buffer
Conversion [N] for CHx
Conversion [N + 1] for CHy
tCC
Data Buffer
Conversion [N] for CHx
tCC
Conversion [N] for CHx
Conversion [N + 14] for CHx
Conversion [N + 15] for CHy
Conversion [N+1] for CHy
Conversion [N] for CHx
SEQ_START bit is set
by user
High Threshold
CHy is the channel which first triggered the ALERT
Conversion [N + 14] for CHx
Conversion [N + 15] for CHx
Conversion [0] for CHx
SEQ_START bit is set
by user
Conversion [0] for CHx
Conversion [1] for CHy
BUSY/RDY
BUSY/RDY
Time
Time
Figure 51. Pre Alert Data for Single Channel
Configurations
Figure 52. Pre Alert Data for Dual Channel
Configuration
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
33
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
7.4.3.1.2
www.ti.com
Autonomous Mode With Post Alert Data
In this mode, the device captures the next sixteen conversion results after the Alert is active. Once these sixteen
conversions are stored in the data buffer, all conversion stops. For this mode, Set DATA_BUFFER_OPMODE to
110b. In this mode, the device starts converting the data on setting the SEQ_START bit and stores the data in
the data buffer when one of the digital comparator flags is set after the crossing a high threshold or a low
threshold for the channels selected in the sequence. if the SEQ_ABORT bit is set before the data buffer is filled,
the device aborts the sequence and stops storing the conversion results.
ADC Conversion Result
Figure 53 and Figure 54 show the filling of the data buffer in autonomous mode with Post Alert Data.
Conversion [N+ 14] for CHx
Conversion [N+ 15] for CHx
Sets the Output of the
Comparator
SEQ_START bit is set
by user
Conversion [N] for CHx
tCC
Data Buffer
Conversion [N] for CHx
Device Starts storing data in
buffer and sets the Latched flag
and alert pin after the count is
reached
Conversion [N] for CHx
Hysteresis
Data Buffer
Conversion [N] for CHx
Conversion [N + 14] for CHx
Conversion [N + 15] for CHx
SEQ_START bit is set
by user
High Threshold - Hysteresis
Conversion [0] for CHx
Conversion [N+1] for CHy
Conversion [N + 14] for CHx
Conversion [N + 15] for CHy
CHx is the channel which first triggered the ALERT
Sets the Output of the
Comparator
High Threshold
Conversion [N+ 15] for CHy
Conversion [N + 1] for CHy
tCC
Device Starts storing data in
buffer and sets the Latched flag
and alert pin after count(=4) is
reached
Device stops conversions and
stops storing data in the buffer
after the data buffer is filled
ADC Conversion Result
Device stops conversions and
stops storing data in buffer after
the data buffer is filled
High Threshold
Conversion [0] for CHx
Conversion [1] for CHy
BUSY/RDY
Time
BUSY/RDY
Figure 54. Post Alert Data for Dual Channel
Configuration
Time
Figure 53. Post Alert Data for Single Channel
Configurations
34
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
7.4.3.2 Autonomous Mode With Burst Data
In this mode, the device can be configured to store up-to 16 conversion results in the data buffer based on user
command. Applications that could take advantage of this mode are remote data loggers, environmental sensing
and patient monitors. In this mode, the user can either start the burst or stop the burst of data as described in the
following sections:
7.4.3.2.1 Autonomous Mode With Start Burst
Device stops conversions and stops filling
the data buffer after the buffer is filled
Conversion [15] for CHx
ADC Conversion Result
ADC Conversion Result
For this mode, set DATA_BUFFER_OPMODE to 001b. With Start Burst, the user can configure the device to
start the filling of data buffer with conversion results by setting the SEQ_START bit and the device stops
converting data and filling the data buffer after the data buffer is filled.
Conversion [14] for CH0
Device stops conversions and
stops storing data after the data
buffer is filled
Conversion [15] for CH1
Data Buffer
Conversion [0] for CH0
Conversion [1] for CH1
Data Buffer
Conversion [0] for CHx
tCC
tCC
SEQ_START bit is set
by user
Conversion [0] for CHx
Conversion [14] for CHx
Conversion [15] for CHx
Device starts
conversions and starts
storing data in the buffer
on setting the
SEQ_START bit
Conversion [14] for CH0
Conversion [15] for CH1
Conversion [0] for CH0
Conversion [1] for CH1
BUSY/RDY
BUSY/RDY
Time
Time
Figure 55. Start Burst with Single Channel
Configurations
Figure 56. Start Burst with Dual Channel
Configuration
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
35
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
7.4.3.2.2 Autonomous Mode With Stop Burst
Device stops conversions and stops filling the
data buffer on setting the SEQ_ABORT bit
Conversion [N+ 15] for CHx
ADC Conversion Result
ADC Conversion Result
For this mode, Set DATA_BUFFER_OPMODE to 000b. With Stop Burst, the user can configure the device to
stop filling the data buffer with conversion results by setting the SEQ_ABORT bit. If more than 16 conversions
occur between start of sequence and abort of sequence, the entries first written into the data buffer are overwritten. Figure 57 and Figure 58 illustrate the filling of the data buffer in autonomous mode with Stop Burst.
Conversion [N+ 14] for CH0
Device stops conversions and
stops storing data on setting the
SEQ_ABORT bit
Conversion [N+ 15] for CH1
tCC
Data Buffer
Conversion [N] for CH0
tCC
Conversion [N + 1] for CH1
Data Buffer
Conversion [N] for CHx
Conversion [N] for CH0
Conversion [N] for CHx
SEQ_START bit is set
by user
Conversion [0] for CHx
Conversion [N + 14] for CH0
Conversion [N + 15] for CH1
Conversion [N+1] for CH1
Conversion [N + 14] for CHx
Conversion [N + 15] for CHx
SEQ_START bit is set
by user
Conversion [0] for CH0
Conversion [1] for CH1
BUSY/RDY
BUSY/RDY
Time
Time
Figure 57. Stop Burst with Single Channel
Configurations
Figure 58. Stop Burst with Dual Channel
Configuration
7.4.4 High Precision Mode
The High Precision Mode increases the accuracy of the data measurement to 16-bit accuracy. This is useful for
applications where the level of precision required to accurately measure the sensor output needs to be higher
than 12 bits. Applications that could take advantage of this type of functionality include gas detectors, air quality
testers, water quality testers, and so on.
For this mode, Set the OPMODE_SEL register to 111b. In this mode, the device starts converting and starts
accumulating the conversion results in an accumulator on setting the SEQ_START bit. The device stops
accumulating the conversion results in accumulator after 16 conversions or when the SEQ_ABORT bit is set.
Upon accumulating 16 twelve bit conversions, the accumulator contains one 16 bit conversion result. The device
has an accumulator for each channel and the device accumulates conversion results from each channel into the
respective accumulator. If the operation of the device is aborted in high precision mode before the BUSY/RDY
pin goes low, the device provides invalid data. In this mode, on providing a device address and read bit for
reading data buffer (Figure 44), the device provides zeroes as output. In this mode, the BUSY/RDY can be used
to wake up the MCU or host from sleep or hibernation on completion of accumulation. The steps for configuring
the device into High Precision Mode are illustrated in Figure 59 .
36
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
High Precision Mode(1)
Select the Channels in AUTO
Sequence(2)
Select the Oscillator
& Set the nCLK value(3)
Enable the accumulator(4)
Set the SEQ_START Bit(5)
Device Starts Conversions
& Starts Accumulating Data
Check Busy/RDY
pin to see if 16
accumulations are
completed
No
Yes
Read the Accumulated Results(6)
Continue in High
Presicion Mode
Yes
No
Exit to another Operation Mode(7)
(1)
For setting the operation mode to High Precision mode, Refer to Figure 47
(2)
Select the channels in the AUTO_SEQ_CHEN register.
(3)
Select the oscillator by configuring the OSC_SEL register and configure the NCLK_SEL register.
(4)
Enable the accumulator by setting bits in the ACC_EN register.
(5)
Set the bit SEQ_START bit in the START_SEQUENCE register.
(6)
Read the ACC_CHx_xxx registers.
(7)
Select another operation mode in the OPMODE_SEL register.
(8)
For reading and writing registers, Refer to Programming section.
Figure 59. Configuring Device in High Precision Mode
TI recommends aborting the present sequence by setting the SEQ_ABORT bit before changing the device
operation mode or device configuration.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
37
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
ADC Conversion Result
Figure 60 and Figure 61 show the accumulation of conversion results in high-precision mode.
Device stops after
accumulating 16
conversion results
Device starts
accumulating on setting
the SEQ_START bit
tCC
Conversion [15] for CHx
Conversion [0] for CHx
BUSY/RDY
Time
ADC Conversion Result
Figure 60. High-Precision Mode With Single-Channel Configurations
Accumulated in
Accumulator for CH0
Device starts
accumulating on setting
the SEQ_START bit
Device stops after
accumulating 16
conversion results
tCC
Conversion [15] for CH0
Conversion [0]
for CH0
Conversion [15] for CH1
Conversion [0] for CH1
Accumulated in
Accumulator for CH1
BUSY/RDY
Time
Figure 61. High-Precision Mode With Dual-Channel Configurations
38
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
7.5 Programming
Table 3 provides the acronyms for different conditions in an I2C Frame.
Table 3. I2C Frame Acronyms
SYMBOL
DESCRIPTION
S
START condition for I2C frame
Sr
RESTART condition for I2C frame
P
STOP condition for I2C frame
A
ACK (low)
N
NACK (high)
R
Read bit (high)
W
Write bit (low)
Table 4. Opcodes for Commands
OPCODE
COMMAND DESCRIPTION
00010000b
Single register read
00001000b
Single register write
00011000b
Set bit
00100000b
Clear bit
00110000b
Reading a continuous block of registers
00101000b
Writing a continuous block of registers
7.5.1 Reading Registers
The I2C master can either read a single register or a continuous block registers from the device as described in
Single Register Read and in Reading a Continuous Block of Registers.
7.5.1.1 Single Register Read
To read a single register from the device, the I2C master has to first provide an I2C command with three frames
(of 8-bits each) to set the address as illustrated in Figure 62. The register address is the address of the register
which must be read. The opcode for register read command is listed in Table 4.
S
Device Address (7 Bits)
W
A
Register Read or Block Read
Opcode (8 Bits)
A
Register Address (8 Bits)
A
P/Sr
Data from Host to Device
Data from Device to Host
Figure 62. Setting Register Address for Reading Registers
After this, the I2C master has to provide another I2C frame containing the device address and read bit as
illustrated in Figure 63. After this frame, the device provides register data. If the host provides more clocks, the
device provides same register data. To end the register read command, the master has to provide a STOP or a
RESTART condition in the I2C frame.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
39
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
S
Device Address (7 Bits)
www.ti.com
R
A
Register Data (8 Bits)
A
P/Sr
Data from Host to Device
Data from Device to Host
Figure 63. Reading Register Data
7.5.1.2 Reading a Continuous Block of Registers
To read a continuous block of registers, the I2C master has to first provide an I2C command to set the address as
illustrated in Figure 62. The register address is the address of the first register in the block which must be read.
The opcode for reading a continuous block of register is listed in Table 4.
Next, the I2C master has to provide another I2C frame containing the device address and read bit as illustrated in
Figure 64. After this frame, the device provides register data. On providing more clocks, the device provides data
for next register. On reading data from addresses which does not exist in the Register Map of the device, the
device returns zeros. If the device does not have any further registers to provide the data, it provides zeros. To
end the register read command, the master has to provide a STOP or a RESTART condition in the I2C frame.
S
Device Address (7 Bits)
R
A
Register Data (8 Bits) for Register N
A
Register Data (8 Bits) for Register N+1
A
Register Data (8 Bits) for Register N+2
A
Register Data (8 Bits) for Register N+k
A
P/Sr
Data from Host to Device
Data from Device to Host
Figure 64. Reading a Continuous Block of Registers
7.5.2 Writing Registers
The I2C master can either write a single register or a continuous block registers to the device. It can also set a
few bits in a register or clear a few bits in a register.
7.5.2.1 Single Register Write
To write to a single register in the device, the I2C master has to provide an I2C command with four frames as
illustrated in Figure 65. The register address is the address of the register which must be written and register
data is the value that must be written. The opcode for single register write is listed in Table 4. To end the register
write command, the master has to provide a STOP or a RESTART condition in the I2C frame.
S
Device Address (7 Bits)
W
A
Write Register or Set Bit or Clear Bit
Opcode (8 Bits)
A
Register Address (8 Bits)
A
Register Data (8 Bits)
A
P/Sr
Data from Host to Device
Data from Device to Host
Figure 65. Writing a Single Register
40
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
7.5.2.2 Set Bit
To set bits in a register without changing the other bits, the I2C master has to provide an I2C command with four
frames as illustrated in Figure 65. The register address is the address of the register in which the bits needs to
be set and register data is the value representing the bits which need to be set. Bits with value as 1 in register
data are set and bits with value as 0 in register data are not changed. The opcode for set bit is listed in Table 4.
To end this command, the master has to provide a STOP or RESTART condition in the I2C frame.
7.5.2.3 Clear Bit
To clear bits in a register without changing the other bits, the I2C master has to provide an I2C command with
four frames as illustrated in Figure 65. The register address is the address of the register in which the bits needs
to be cleared and register data is the value representing the bits which need to be cleared. Bits with value as 1 in
register data are cleared and bits with value as 0 in register data are not changed. The opcode for clear bit is
listed in Table 4. To end this command, the master has to provide a STOP or a RESTART condition in the I2C
frame.
7.5.2.4 Writing a Continuous Block of Registers
To write to a continuous block of registers, the I2C master has to provide an I2C command as illustrated in
Figure 66. The register address is the address of the first register in the block which needs to be written. The I2C
master has to provide data for registers in subsequent I2C frames in an ascending order of register addresses.
Writing data to addresses which do not exist in the Register Map of the device has no effect. The opcode for
writing a continuous block of registers is listed in Table 4. If the data provided by the I2C master exceeds the
address space of the device, the device neglects the data beyond the address space. To end the register write
command, the master has to provide a STOP or a RESTART condition in the I2C frame.
S
Device Address (7 Bits)
Register Data (8 Bits) for Register N+1
W
A
Block Write Opcode (8 Bits)
A
Register Address (8 Bits)
A
A
Register Data (8 Bits) for Register N
A
Register Data (8 Bits) for Register N+k
A
P/Sr
Data from Host to Device
Data from Device to Host
Figure 66. Writing a Continuous Block of Registers
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
41
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
7.6 Register Map
7.6.1 ADS7142-Q1 Registers
Table 5 lists the ADS7142-Q1 registers. All register offset addresses not listed in Table 5 should be considered
as reserved locations and the register contents should not be modified.
Table 5. ADS7142-Q1 Registers
Offset
42
Acronym
Register Name
0h
OPMODE_I2CMODE_STATUS
Device operation mode register
OPMODE_I2CM
ODE_STATUS
Register (Offset =
0h) [reset = 0h]
1h
DATA_BUFFER_STATUS
Data buffer status register
DATA_BUFFER_
STATUS Register
(Offset = 1h)
[reset = 0h]
2h
ACCUMULATOR_STATUS
Status of ADC accumulator
ACCUMULATOR
_STATUS
Register (Offset =
2h) [reset = 0h]
3h
ALERT_TRIG_CHID
Alert trigeer channel ID
ALERT_TRIG_C
HID Register
(Offset = 3h)
[reset = 0h]
4h
SEQUENCE_STATUS
Sequence status register
SEQUENCE_ST
ATUS Register
(Offset = 4h)
[reset = 0h]
8h
ACC_CH0_LSB
CH0 accumulator data register (LSB)
ACC_CH0_LSB
Register (Offset =
8h) [reset = 0h]
9h
ACC_CH0_MSB
CH0 accumulated data register (MSB)
ACC_CH0_MSB
Register (Offset =
9h) [reset = 0h]
Ah
ACC_CH1_LSB
CH1 accumulated data register (LSB)
ACC_CH1_LSB
Register (Offset =
Ah) [reset = 0h]
Bh
ACC_CH1_MSB
CH1 accumulated data register (MSB)
ACC_CH1_MSB
Register (Offset =
Bh) [reset = 0h]
Ch
ALERT_LOW_FLAGS
Alert low flags register
ALERT_LOW_FL
AGS Register
(Offset = Ch)
[reset = 0h]
Eh
ALERT_HIGH_FLAGS
Alert high flags register
ALERT_HIGH_FL
AGS Register
(Offset = Eh)
[reset = 0h]
14h
DEVICE_RESET
Device reset register
DEVICE_RESET
Register (Offset =
14h) [reset = 0h]
15h
OFFSET_CAL
Offset calibration register
OFFSET_CAL
Register (Offset =
15h) [reset = 0h]
17h
WKEY
Write key for writing into DEVICE_RESET register
18h
OSC_SEL
Oscillator selection register
Submit Documentation Feedback
Section
WKEY Register
(Offset = 17h)
[reset = 0h]
OSC_SEL
Register (Offset =
18h) [reset = 0h]
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Table 5. ADS7142-Q1 Registers (continued)
Offset
Acronym
Register Name
19h
NCLK_SEL
nCLK selection register
NCLK_SEL
Register (Offset =
19h) [reset = 0h]
Section
1Ch
OPMODE_SEL
Device operation mode selection
OPMODE_SEL
Register (Offset =
1Ch) [reset = 0h]
1Eh
START_SEQUENCE
Start channel scanning sequence register
START_SEQUEN
CE Register
(Offset = 1Eh)
[reset = 0h]
1Fh
ABORT_SEQUENCE
Abort channel sequence register
ABORT_SEQUE
NCE Register
(Offset = 1Fh)
[reset = 0h]
20h
AUTO_SEQ_CHEN
Auto sequencing channel select register
AUTO_SEQ_CH
EN Register
(Offset = 20h)
[reset = 3h]
24h
CH_INPUT_CFG
Channel input configuration register
CH_INPUT_CFG
Register (Offset =
24h) [reset = 0h]
28h
DOUT_FORMAT_CFG
Data buffer word configuration register
DOUT_FORMAT
_CFG Register
(Offset = 28h)
[reset = 0h]
2Ch
DATA_BUFFER_OPMODE
Data buffer operation mode register
DATA_BUFFER_
OPMODE
Register (Offset =
2Ch) [reset = 1h]
30h
ACC_EN
Accumulator control register
ACC_EN
Register (Offset =
30h) [reset = 0h]
34h
ALERT_CHEN
Alert channel enable register
ALERT_CHEN
Register (Offset =
34h) [reset = 0h]
36h
PRE_ALT_MAX_EVENT_COUNT
Pre-alert count register
PRE_ALT_MAX_
EVENT_COUNT
Register (Offset =
36h) [reset = 0h]
37h
ALERT_DWC_EN
Alert digital window comparator register
ALERT_DWC_E
N Register (Offset
= 37h) [reset =
0h]
38h
DWC_HTH_CH0_LSB
CH0 high threshold LSB register
DWC_HTH_CH0
_LSB Register
(Offset = 38h)
[reset = 0h]
39h
DWC_HTH_CH0_MSB
CH0 high threshold MSB register
DWC_HTH_CH0
_MSB Register
(Offset = 39h)
[reset = 0h]
3Ah
DWC_LTH_CH0_LSB
CH0 low threshold LSB register
DWC_LTH_CH0_
LSB Register
(Offset = 3Ah)
[reset = 0h]
3Bh
DWC_LTH_CH0_MSB
CH0 low threshold MSB register
DWC_LTH_CH0_
MSB Register
(Offset = 3Bh)
[reset = 0h]
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
43
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Table 5. ADS7142-Q1 Registers (continued)
Offset
Acronym
Register Name
3Ch
DWC_HTH_CH1_LSB
CH1 high threshold LSB register
DWC_HTH_CH1
_LSB Register
(Offset = 3Ch)
[reset = 0h]
Section
3Dh
DWC_HTH_CH1_MSB
CH1 high threshold MSB register
DWC_HTH_CH1
_MSB Register
(Offset = 3Dh)
[reset = 0h]
3Eh
DWC_LTH_CH1_LSB
CH1 low threshold LSB register
DWC_LTH_CH1_
LSB Register
(Offset = 3Eh)
[reset = 0h]
3Fh
DWC_LTH_CH1_MSB
CH1 low threshold MSB register
DWC_LTH_CH1_
MSB Register
(Offset = 3Fh)
[reset = 0h]
40h
DWC_HYS_CH0
CH0 comparator hysterisis register
DWC_HYS_CH0
Register (Offset =
40h) [reset = 0h]
41h
DWC_HYS_CH1
CH1 comparator hysterisis register
DWC_HYS_CH1
Register (Offset =
41h) [reset = 0h]
Complex bit access types are encoded to fit into small table cells. Table 6 shows the codes that are used for
access types in this section.
Table 6. ADS7142-Q1 Access Type Codes
Access Type
Code
Description
R
Read
W
Write
Read Type
R
Write Type
W
Reset or Default Value
-n
Value after reset or the default
value
Register Array Variables
i,j,k,l,m,n
When these variables are used in
a register name, an offset, or an
address, they refer to the value of
a register array where the register
is part of a group of repeating
registers. The register groups form
a hierarchical structure and the
array is represented with a
formula.
y
When this variable is used in a
register name, an offset, or an
address it refers to the value of a
register array.
7.6.1.1 OPMODE_I2CMODE_STATUS Register (Offset = 0h) [reset = 0h]
OPMODE_I2CMODE_STATUS is shown in Figure 67 and described in Table 7.
Return to the Summary Table.
Device operation mode register
44
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Figure 67. OPMODE_I2CMODE_STATUS Register
7
6
5
RESERVED
R-00000b
4
3
2
HS_MODE
R-0b
1
0
DEV_OPMODE[1:0]
R-00b
Table 7. OPMODE_I2CMODE_STATUS Register Field Descriptions
Bit
Field
Type
Reset
Description
7-3
RESERVED
R
00000b
Reserved bits. Read returns 00000b.
2
HS_MODE
R
0b
This bit indicates when device is in high speed mode for I2C
Interface.
0b = 1 : Device is not in high speed mode for I2C Interface.
1b = 2 : Device is in high speed mode for I2C Interface.
1-0
DEV_OPMODE[1:0]
R
00b
These bits indicate funtional mode of the device.
00b = 1 : Device is operating in manual mode.
01b = 2 : Not used.
10b = 3 : Device is operating in autonomous monitoring mode.
11b = 4 : Device is operating in high precision mode.
7.6.1.2 DATA_BUFFER_STATUS Register (Offset = 1h) [reset = 0h]
DATA_BUFFER_STATUS is shown in Figure 68 and described in Table 8.
Return to the Summary Table.
Data buffer status register
Figure 68. DATA_BUFFER_STATUS Register
7
6
RESERVED
R-000b
5
4
3
2
DATA_WORDCOUNT[4:0]
R-00000b
1
0
Table 8. DATA_BUFFER_STATUS Register Field Descriptions
Bit
Field
Type
Reset
Description
7-5
RESERVED
R
000b
Reserved bits. Read returns 000b.
4-0
DATA_WORDCOUNT[4:0 R
]
00000b
DATA_WORDCOUNT [00000] to [10000] = Number of entries filled
in data buffer (0 to 16)
7.6.1.3 ACCUMULATOR_STATUS Register (Offset = 2h) [reset = 0h]
ACCUMULATOR_STATUS is shown in Figure 69 and described in Table 9.
Return to the Summary Table.
Status of ADC accumulator
Figure 69. ACCUMULATOR_STATUS Register
7
6
5
4
3
RESERVED
R-0000b
2
1
ACC_COUNT[3:0]
R-0000b
0
Table 9. ACCUMULATOR_STATUS Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
RESERVED
R
0000b
Reserved bits. Read returns 0000b.
3-0
ACC_COUNT[3:0]
R
0000b
ACC_COUNT = Number of accumulation completed till last finished
conversion.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
45
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
7.6.1.4 ALERT_TRIG_CHID Register (Offset = 3h) [reset = 0h]
ALERT_TRIG_CHID is shown in Figure 70 and described in Table 10.
Return to the Summary Table.
Alert trigeer channel ID
Figure 70. ALERT_TRIG_CHID Register
7
6
5
ALERT_TRIG_CHID[3:0]
R-0000b
4
3
2
1
0
RESERVED
R-0000b
Table 10. ALERT_TRIG_CHID Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
ALERT_TRIG_CHID[3:0]
R
0000b
These bits provide the channel ID of channel which was first to set
the alert output.
0000b = 1 : Channel 0.
0001b = 2 : Channel 1.
3-0
RESERVED
R
0000b
Reserved bits. Reads returns 0000b.
7.6.1.5 SEQUENCE_STATUS Register (Offset = 4h) [reset = 0h]
SEQUENCE_STATUS is shown in Figure 71 and described in Table 11.
Return to the Summary Table.
Sequence status register
Figure 71. SEQUENCE_STATUS Register
7
6
5
RESERVED
R-00000b
4
3
2
1
SEQ_ERR_ST[1:0]
R-00b
0
RESERVED
R-0b
Table 11. SEQUENCE_STATUS Register Field Descriptions
Bit
Field
Type
Reset
Description
7-3
RESERVED
R
00000b
Reserved bits. Read returns 00000b.
2-1
SEQ_ERR_ST[1:0]
R
00b
These bits give status of device sequence.
00b = 1 : Auto sequencing disabled, no error.
01b = 2 : Auto sequencing enabled, no error.
10b = 3 : Not used.
11b = 4 : Auto sequencing enabled, device in error.
0
RESERVED
R
0b
Reserved bit. Read returns 0b.
7.6.1.6 ACC_CH0_LSB Register (Offset = 8h) [reset = 0h]
ACC_CH0_LSB is shown in Figure 72 and described in Table 12.
Return to the Summary Table.
CH0 accumulator data register (LSB)
Figure 72. ACC_CH0_LSB Register
7
6
5
4
3
2
1
0
CH0_LSB[7:0]
R-00000000b
46
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Table 12. ACC_CH0_LSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
CH0_LSB[7:0]
R
00000000b
LSB of accumulated data for CH0.
7.6.1.7 ACC_CH0_MSB Register (Offset = 9h) [reset = 0h]
ACC_CH0_MSB is shown in Figure 73 and described in Table 13.
Return to the Summary Table.
CH0 accumulated data register (MSB)
Figure 73. ACC_CH0_MSB Register
7
6
5
4
3
2
1
0
1
0
1
0
CH0_MSB[7:0]
R-00000000b
Table 13. ACC_CH0_MSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
CH0_MSB[7:0]
R
00000000b
MSB of accumulated data for CH0.
7.6.1.8 ACC_CH1_LSB Register (Offset = Ah) [reset = 0h]
ACC_CH1_LSB is shown in Figure 74 and described in Table 14.
Return to the Summary Table.
CH1 accumulated data register (LSB)
Figure 74. ACC_CH1_LSB Register
7
6
5
4
3
2
CH1_LSB[7:0]
R-00000000b
Table 14. ACC_CH1_LSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
CH1_LSB[7:0]
R
00000000b
LSB of accumulated data for CH1.
7.6.1.9 ACC_CH1_MSB Register (Offset = Bh) [reset = 0h]
ACC_CH1_MSB is shown in Figure 75 and described in Table 15.
Return to the Summary Table.
CH1 accumulated data register (MSB)
Figure 75. ACC_CH1_MSB Register
7
6
5
4
3
2
CH1_MSB[7:0]
R-00000000b
Table 15. ACC_CH1_MSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
CH1_MSB[7:0]
R
00000000b
MSB of accumulated data for CH1.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
47
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
7.6.1.10 ALERT_LOW_FLAGS Register (Offset = Ch) [reset = 0h]
ALERT_LOW_FLAGS is shown in Figure 76 and described in Table 16.
Return to the Summary Table.
Alert low flags register
Figure 76. ALERT_LOW_FLAGS Register
7
6
5
4
3
2
RESERVED
R-000000b
1
ALERT_LOW_
CH1
R/W-0b
0
ALERT_LOW_
CH0
R/W-0b
Table 16. ALERT_LOW_FLAGS Register Field Descriptions
Bit
Field
Type
Reset
Description
7-2
RESERVED
R
000000b
Reserved bits. Read returns 000000b.
ALERT_LOW_CH1
R/W
0b
This bit indicates alert on low side comparator for CH1.
1
0b = 1 : Alert is not set for low side comparator for CH1.
1b = 2 : Alert is set for low side comparator for CH1.
0
ALERT_LOW_CH0
R/W
0b
This bit indicates alert on low side comparator for CH0.
0b = 1 : Alert is not set for low side comparator for CH0.
1b = 2 : Alert is set for low side comparator for CH0.
7.6.1.11 ALERT_HIGH_FLAGS Register (Offset = Eh) [reset = 0h]
ALERT_HIGH_FLAGS is shown in Figure 77 and described in Table 17.
Return to the Summary Table.
Alert high flags register
Figure 77. ALERT_HIGH_FLAGS Register
7
6
5
4
3
RESERVED
R-000000b
2
1
ALERT_HIGH_
CH1
R/W-0b
0
ALERT_HIGH_
CH0
R/W-0b
Table 17. ALERT_HIGH_FLAGS Register Field Descriptions
Bit
Field
Type
Reset
Description
7-2
RESERVED
R
000000b
Reserved bits. Read returns 000000b.
ALERT_HIGH_CH1
R/W
0b
This bit indicates alert on high side comparator of CH1.
1
0b = 1 : Alert is not set for high side comparator for CH1.
1b = 2 : Alert is set for high side comparator for CH1.
0
ALERT_HIGH_CH0
R/W
0b
This bit indicates alert on high side comparator for CH0.
0b = 1 : Alert is not set for high side comparator for CH0.
1b = 2 : Alert is set for high side comparator for CH0.
7.6.1.12 DEVICE_RESET Register (Offset = 14h) [reset = 0h]
DEVICE_RESET is shown in Figure 78 and described in Table 18.
Return to the Summary Table.
Device reset register
48
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Figure 78. DEVICE_RESET Register
7
6
5
4
RESERVED
R-0000000b
3
2
1
0
DEV_RST
W-0b
1
0
TRIG_OFFCAL
W-0b
Table 18. DEVICE_RESET Register Field Descriptions
Bit
Field
Type
Reset
Description
7-1
RESERVED
R
0000000b
Reserved bits. Read returns 0000000b.
DEV_RST
W
0b
Writing 1 to this bit resets the device.
0
7.6.1.13 OFFSET_CAL Register (Offset = 15h) [reset = 0h]
OFFSET_CAL is shown in Figure 79 and described in Table 19.
Return to the Summary Table.
Offset calibration register
Figure 79. OFFSET_CAL Register
7
6
5
4
RESERVED
R-0000000b
3
2
Table 19. OFFSET_CAL Register Field Descriptions
Bit
Field
Type
Reset
Description
7-1
RESERVED
R
0000000b
Reserved bits. Read returns 0000000b.
TRIG_OFFCAL
W
0b
Writing 1 into this bit triggers internal offset calibration.
0
7.6.1.14 WKEY Register (Offset = 17h) [reset = 0h]
WKEY is shown in Figure 80 and described in Table 20.
Return to the Summary Table.
Write key for writing into DEVICE_RESET register
Figure 80. WKEY Register
7
6
5
4
3
2
1
RESERVED
R-0000b
0
WKEY[3:0]
R/W-0000b
Table 20. WKEY Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
RESERVED
R
0000b
Reserved bits. Do not write. Read returns 0000b.
3-0
WKEY[3:0]
R/W
0000b
Write 1010b into these bits to get write access for the
DEVICE_RESET and OFFSET_CAL register. WKEY register is not
reset to default value on device reset (see Reset section). After
coming out of device reset, write 00h to the WKEY register to
prevent erroneous reset.
7.6.1.15 OSC_SEL Register (Offset = 18h) [reset = 0h]
OSC_SEL is shown in Figure 81 and described in Table 21.
Return to the Summary Table.
Oscillator selection register
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
49
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Figure 81. OSC_SEL Register
7
6
5
4
RESERVED
R-0000000b
3
2
1
0
HSZ_LP
R/W-0b
Table 21. OSC_SEL Register Field Descriptions
Bit
Field
Type
Reset
Description
7-1
RESERVED
R
0000000b
Reserved bits. Read returns 0000000b.
HSZ_LP
R/W
0b
This bit selects oscillator used for the conversion process and cycle
time for a single conversion.
0
0b = 1 : Device uses high speed oscillator.
1b = 2 : Device uses low power oscillator.
7.6.1.16 NCLK_SEL Register (Offset = 19h) [reset = 0h]
NCLK_SEL is shown in Figure 82 and described in Table 22.
Return to the Summary Table.
nCLK selection register
Figure 82. NCLK_SEL Register
7
6
5
4
3
2
1
0
NCLK[7:0]
R/W-00000000b
Table 22. NCLK_SEL Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
NCLK[7:0]
R/W
00000000b
Sets number of clocks of the oscillator that the device uses for one
conversion cycle. When using the High Speed Oscillator: For Value x
written into the nCLK register • if x ≤ 21, nCLK is set to 21
(00010101b) • if x > 21, nCLK is set to x When using the Low Power
Oscillator, For Value x written into the nCLK register: • if x ≤ 18,
nCLK is set to 18 (00010010b) • if x > 18, nCLK is set to x
7.6.1.17 OPMODE_SEL Register (Offset = 1Ch) [reset = 0h]
OPMODE_SEL is shown in Figure 83 and described in Table 23.
Return to the Summary Table.
Device operation mode selection
Figure 83. OPMODE_SEL Register
7
50
6
5
RESERVED
R-00000b
4
3
Submit Documentation Feedback
2
1
SEL_OPMODE[2:0]
R/W-000b
0
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Table 23. OPMODE_SEL Register Field Descriptions
Bit
Field
Type
Reset
Description
7-3
RESERVED
R
00000b
Reserved bits. Read returns 00000b
2-0
SEL_OPMODE[2:0]
R/W
000b
These bits set the functional mode for the device.
000b = 1 : Manual mode with CH0 only (Default mode).
001b = 2 : Manual mode with CH0 only (Default mode).
010b = 3 : Reserved. Do not use.
011b = 4 : Reserved. Do not use.
100b = 5 : Manual mode with AUTO Sequencing enabled.
101b = 6 : Manual Mode with AUTO Sequencing enabled.
110b = 7 : Autonomous monitoring mode with AUTO sequencing
enabled.
111b = 8 : High precision mode with AUTO sequencing enabled.
7.6.1.18 START_SEQUENCE Register (Offset = 1Eh) [reset = 0h]
START_SEQUENCE is shown in Figure 84 and described in Table 24.
Return to the Summary Table.
Start channel scanning sequence register
Figure 84. START_SEQUENCE Register
7
6
5
4
RESERVED
R-0000000b
3
2
1
0
SEQ_START
W-0b
Table 24. START_SEQUENCE Register Field Descriptions
Bit
Field
Type
Reset
Description
7-1
RESERVED
R
0000000b
Reserved bits. Read returns 0000000b.
0
SEQ_START
W
0b
Setting this bit to 1 brings the BUSY/RDY pin high and starts the first
conversion in the sequence.
7.6.1.19 ABORT_SEQUENCE Register (Offset = 1Fh) [reset = 0h]
ABORT_SEQUENCE is shown in Figure 85 and described in Table 25.
Return to the Summary Table.
Abort channel sequence register
Figure 85. ABORT_SEQUENCE Register
7
6
5
4
RESERVED
R-0000000b
3
2
1
0
SEQ_ABORT
W-0b
Table 25. ABORT_SEQUENCE Register Field Descriptions
Bit
Field
Type
Reset
Description
7-1
RESERVED
R
0000000b
Reserved bits. Read returns 0000000b.
SEQ_ABORT
W
0b
Setting this bit to 1 aborts the ongoing conversion and brings the
BUSY/RDY pin low.
0
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
51
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
7.6.1.20 AUTO_SEQ_CHEN Register (Offset = 20h) [reset = 3h]
AUTO_SEQ_CHEN is shown in Figure 86 and described in Table 26.
Return to the Summary Table.
Auto sequencing channel select register
Figure 86. AUTO_SEQ_CHEN Register
7
6
5
4
3
2
RESERVED
R-000000b
1
AUTOSEQ_EN
_CH1
R/W-1b
0
AUTOSEQ_EN
_CH0
R/W-1b
Table 26. AUTO_SEQ_CHEN Register Field Descriptions
Bit
Field
Type
Reset
Description
7-2
RESERVED
R
000000b
Reserved bits. Read returns 000000b.
AUTOSEQ_EN_CH1
R/W
1b
This bit selects CH1 for auto sequencing.
1
0b = 1 : Channel 1 is not selected for auto sequencing.
1b = 2 : Channel 1 is selected for auto sequencing.
0
AUTOSEQ_EN_CH0
R/W
1b
This bit selects CH0 for auto sequencing.
0b = 1 : Channel 0 is not selected for auto sequencing.
1b = 2 : Channel 0 is selected for auto sequencing.
7.6.1.21 CH_INPUT_CFG Register (Offset = 24h) [reset = 0h]
CH_INPUT_CFG is shown in Figure 87 and described in Table 27.
Return to the Summary Table.
Channel input configuration register
Figure 87. CH_INPUT_CFG Register
7
6
5
4
3
2
RESERVED
R-000000b
1
0
CH0_CH1_IP_CFG[1:0]
R/W-00b
Table 27. CH_INPUT_CFG Register Field Descriptions
Bit
Field
Type
Reset
Description
7-2
RESERVED
R
000000b
Reserved bits. Read returns 000000b.
1-0
CH0_CH1_IP_CFG[1:0]
R/W
00b
This bit selects configuration for the input pins.
00b = 1 : Two-channel, single-ended configuration.
01b = 2 : Single-channel, single-ended configuration with remote
ground sensing.
10b = 3 : Single-channel, pseudo-differential configuration.
11b = 4 : Two-channel, single-ended configuration.
7.6.1.22 DOUT_FORMAT_CFG Register (Offset = 28h) [reset = 0h]
DOUT_FORMAT_CFG is shown in Figure 88 and described in Table 28.
Return to the Summary Table.
Data buffer word configuration register
52
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Figure 88. DOUT_FORMAT_CFG Register
7
6
5
4
3
2
1
0
DOUT_FORMAT[1:0]
R/W-00b
RESERVED
R-000000b
Table 28. DOUT_FORMAT_CFG Register Field Descriptions
Bit
Field
Type
Reset
Description
7-2
RESERVED
R
000000b
Reserved bits. Read returns 000000b.
1-0
DOUT_FORMAT[1:0]
R/W
00b
These bits select 16-bit content of the data word in the data buffer.
00b = 1 : 12-bit conversion result followed by 0000b.
01b = 2 : 12-bit conversion result followed by 3-bit channel ID (000b
for CH0, 001b for CH1).
10b = 3 : 12-bit conversion result followed by 3-bit channel ID (000b
for CH0, 001b for CH1) followed by DATA_VALID bit.
11b = 4 : 12-bit conversion result followed by 0000b.
7.6.1.23 DATA_BUFFER_OPMODE Register (Offset = 2Ch) [reset = 1h]
DATA_BUFFER_OPMODE is shown in Figure 89 and described in Table 29.
Return to the Summary Table.
Data buffer operation mode register
Figure 89. DATA_BUFFER_OPMODE Register
7
6
5
RESERVED
R-00000b
4
3
2
1
STARTSTOP_CNTRL[2:0]
R/W-001b
0
Table 29. DATA_BUFFER_OPMODE Register Field Descriptions
Bit
Field
Type
Reset
Description
7-3
RESERVED
R
00000b
Reserved bits. Read returns 00000b.
2-0
STARTSTOP_CNTRL[2:0] R/W
001b
These bits select data buffer mode of operation.
000b = 1 : Stop burst mode.
001b = 2 : Start burst mode, default.
010b = 3 : Reserved, do not use.
011b = 4 : Reserved, do not use.
100b = 5 : Pre alert data mode.
101b = 6 : Reserved, do not use.
110b = 7 : Post alert data mode.
111b = 8 : Reserved, do not use.
7.6.1.24 ACC_EN Register (Offset = 30h) [reset = 0h]
ACC_EN is shown in Figure 90 and described in Table 30.
Return to the Summary Table.
Accumulator control register
Figure 90. ACC_EN Register
7
6
5
4
3
RESERVED
R-0000b
2
1
0
EN_ACC[3:0]
R/W-0000b
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
53
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Table 30. ACC_EN Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
RESERVED
R
0000b
Reserved bits. Read returns 0000b.
3-0
EN_ACC[3:0]
R/W
0000b
These bits enable accumulator function of device. 0001b to 1110b
settings are reserved. Do not use.
0000b = 1 : Accumulator is enabled.
7.6.1.25 ALERT_CHEN Register (Offset = 34h) [reset = 0h]
ALERT_CHEN is shown in Figure 91 and described in Table 31.
Return to the Summary Table.
Alert channel enable register
Figure 91. ALERT_CHEN Register
7
6
5
4
3
2
1
ALERT_EN_C
H1
R/W-0b
RESERVED
R-000000b
0
ALERT_EN_C
H0
R/W-0b
Table 31. ALERT_CHEN Register Field Descriptions
Bit
Field
Type
Reset
Description
7-2
RESERVED
R
000000b
Reserved bits. Read returns 000000b.
ALERT_EN_CH1
R/W
0b
This bit enables alert functionality of CH1.
1
0b = 1 : Alert is disabled for CH1, default.
1b = 2 : Alert is enabled for CH1.
0
ALERT_EN_CH0
R/W
0b
This bit enables alert functionality for CH0.
0b = 1 : Alert is disabled for CH0, default.
1b = 2 : Alert is enabled for CH0.
7.6.1.26 PRE_ALT_MAX_EVENT_COUNT Register (Offset = 36h) [reset = 0h]
PRE_ALT_MAX_EVENT_COUNT is shown in Figure 92 and described in Table 32.
Return to the Summary Table.
Pre-alert count register
Figure 92. PRE_ALT_MAX_EVENT_COUNT Register
7
6
5
PREALERT_COUNT[3:0]
R/W-0000b
4
3
2
1
0
RESERVED
R-0000b
Table 32. PRE_ALT_MAX_EVENT_COUNT Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
PREALERT_COUNT[3:0]
R/W
0000b
These bits set the Pre-Alert Event Count = PREALERT_COUNT
[7:4] + 1
3-0
RESERVED
R
0000b
Reserved bits. Read returns 0000b.
7.6.1.27 ALERT_DWC_EN Register (Offset = 37h) [reset = 0h]
ALERT_DWC_EN is shown in Figure 93 and described in Table 33.
Return to the Summary Table.
Alert digital window comparator register
54
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Figure 93. ALERT_DWC_EN Register
7
6
5
4
RESERVED
3
2
1
R-0000000b
0
DWC_BLOCK_
EN
R/W-0b
Table 33. ALERT_DWC_EN Register Field Descriptions
Bit
Field
Type
Reset
Description
7-1
RESERVED
R
0000000b
Reserved bits. Read returns 0000000b.
DWC_BLOCK_EN
R/W
0b
This bit enables digital window comparator block.
0
0b = 1 : Disables digital window comparator.
1b = 2 : Enables digital window comparator.
7.6.1.28 DWC_HTH_CH0_LSB Register (Offset = 38h) [reset = 0h]
DWC_HTH_CH0_LSB is shown in Figure 94 and described in Table 34.
Return to the Summary Table.
CH0 high threshold LSB register
Figure 94. DWC_HTH_CH0_LSB Register
7
6
5
4
3
HTH_CH0_LSB[7:0]
R/W-00000000b
2
1
0
Table 34. DWC_HTH_CH0_LSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
HTH_CH0_LSB[7:0]
R/W
00000000b
These are 8 least significant bits of high threshold for CH0.
7.6.1.29 DWC_HTH_CH0_MSB Register (Offset = 39h) [reset = 0h]
DWC_HTH_CH0_MSB is shown in Figure 95 and described in Table 35.
Return to the Summary Table.
CH0 high threshold MSB register
Figure 95. DWC_HTH_CH0_MSB Register
7
6
5
4
3
RESERVED
R-0000b
2
1
HTH_CH0_MSB[3:0]
R/W-0000b
0
Table 35. DWC_HTH_CH0_MSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
RESERVED
R
0000b
Reserved bits. Read returns 0000b.
3-0
HTH_CH0_MSB[3:0]
R/W
0000b
These are 4 most significant bits of high threshold for CH0.
7.6.1.30 DWC_LTH_CH0_LSB Register (Offset = 3Ah) [reset = 0h]
DWC_LTH_CH0_LSB is shown in Figure 96 and described in Table 36.
Return to the Summary Table.
CH0 low threshold LSB register
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
55
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Figure 96. DWC_LTH_CH0_LSB Register
7
6
5
4
3
LTH_CH0_LSB[7:0]
R/W-00000000b
2
1
0
Table 36. DWC_LTH_CH0_LSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
LTH_CH0_LSB[7:0]
R/W
00000000b
These are 8 least significant bits of low threshold for CH0.
7.6.1.31 DWC_LTH_CH0_MSB Register (Offset = 3Bh) [reset = 0h]
DWC_LTH_CH0_MSB is shown in Figure 97 and described in Table 37.
Return to the Summary Table.
CH0 low threshold MSB register
Figure 97. DWC_LTH_CH0_MSB Register
7
6
5
4
3
RESERVED
R-0000b
2
1
LTH_CH0_MSB[3:0]
R/W-0000b
0
Table 37. DWC_LTH_CH0_MSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
RESERVED
R
0000b
Reserved bits. Read returns 0000b.
3-0
LTH_CH0_MSB[3:0]
R/W
0000b
These are 4 most significant bits of low threshold for CH0.
7.6.1.32 DWC_HTH_CH1_LSB Register (Offset = 3Ch) [reset = 0h]
DWC_HTH_CH1_LSB is shown in Figure 98 and described in Table 38.
Return to the Summary Table.
CH1 high threshold LSB register
Figure 98. DWC_HTH_CH1_LSB Register
7
6
5
4
3
HTH_CH1_LSB[7:0]
R/W-00000000b
2
1
0
Table 38. DWC_HTH_CH1_LSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
HTH_CH1_LSB[7:0]
R/W
00000000b
These are 8 least significant bits of high threshold for CH1.
7.6.1.33 DWC_HTH_CH1_MSB Register (Offset = 3Dh) [reset = 0h]
DWC_HTH_CH1_MSB is shown in Figure 99 and described in Table 39.
Return to the Summary Table.
CH1 high threshold MSB register
Figure 99. DWC_HTH_CH1_MSB Register
7
6
5
4
3
RESERVED
R-0000b
56
Submit Documentation Feedback
2
1
HTH_CH1_MSB[3:0]
R/W-0000b
0
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Table 39. DWC_HTH_CH1_MSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
RESERVED
R
0000b
Reserved bits. Read returns 0000b.
3-0
HTH_CH1_MSB[3:0]
R/W
0000b
These are 4 most significant bits of high threshold for CH1.
7.6.1.34 DWC_LTH_CH1_LSB Register (Offset = 3Eh) [reset = 0h]
DWC_LTH_CH1_LSB is shown in Figure 100 and described in Table 40.
Return to the Summary Table.
CH1 low threshold LSB register
Figure 100. DWC_LTH_CH1_LSB Register
7
6
5
4
3
LTH_CH1_LSB[7:0]
R/W-00000000b
2
1
0
Table 40. DWC_LTH_CH1_LSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-0
LTH_CH1_LSB[7:0]
R/W
00000000b
These are 8 least significant bits of low threshold for CH1.
7.6.1.35 DWC_LTH_CH1_MSB Register (Offset = 3Fh) [reset = 0h]
DWC_LTH_CH1_MSB is shown in Figure 101 and described in Table 41.
Return to the Summary Table.
CH1 low threshold MSB register
Figure 101. DWC_LTH_CH1_MSB Register
7
6
5
4
3
2
1
LTH_CH1_MSB[3:0]
R/W-0000b
RESERVED
R-0000b
0
Table 41. DWC_LTH_CH1_MSB Register Field Descriptions
Bit
Field
Type
Reset
Description
7-4
RESERVED
R
0000b
Reserved bits. Read returns 0000b.
3-0
LTH_CH1_MSB[3:0]
R/W
0000b
These are 4 most significant bits of low threshold for CH1.
7.6.1.36 DWC_HYS_CH0 Register (Offset = 40h) [reset = 0h]
DWC_HYS_CH0 is shown in Figure 102 and described in Table 42.
Return to the Summary Table.
CH0 comparator hysterisis register
Figure 102. DWC_HYS_CH0 Register
7
6
5
RESERVED
R-00b
4
3
2
1
0
HYS_CH0[5:0]
R/W-000000b
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
57
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Table 42. DWC_HYS_CH0 Register Field Descriptions
Bit
Field
Type
Reset
Description
7-6
RESERVED
R
00b
Reserved bits. Read returns 00b.
5-0
HYS_CH0[5:0]
R/W
000000b
These bits set hysteresis for both comparators for CH0.
7.6.1.37 DWC_HYS_CH1 Register (Offset = 41h) [reset = 0h]
DWC_HYS_CH1 is shown in Figure 103 and described in Table 43.
Return to the Summary Table.
CH1 comparator hysterisis register
Figure 103. DWC_HYS_CH1 Register
7
6
5
4
RESERVED
R-00b
3
2
1
0
HYS_CH1[5:0]
R/W-000000b
Table 43. DWC_HYS_CH1 Register Field Descriptions
58
Bit
Field
Type
Reset
Description
7-6
RESERVED
R
00b
Reserved bits. Read returns 00b.
5-0
HYS_CH1[5:0]
R/W
000000b
These bits set hysteresis for both comparators for CH1.
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
In an increasing number of industrial applications, data acquisition sub-systems are collecting more data about
the environment in which the system is operating and applying deep learning algorithms in order to improve
system reliability, implement preventative maintenance, and/or enhance the quality of data collected by the
system. The ADS7142-Q1 can be used to connect to a variety of sensors and can provide deeper data analytics
at lower power levels than existing solutions. The depth of analysis that can be performed on the data collected
by the ADS7142-Q1 is enhanced by the internal data buffer, programmable alarm thresholds and hysteresis,
event counter, and internal calibration circuitry. The applications circuits described in this section highlight
specific use-cases of the ADS7142-Q1 for data collection that can further increase the depth and quality of the
data being measured by the system.
8.2 Typical Applications
8.2.1 ADS7142-Q1 as a Programmable Comparator With False Trigger Prevention and Diagnostics
+VDD
R
RL
No 1
VREF(UPPER)
+
A1
VOUT
VIN
R
+
VREF(LOWER)
A2
R
Copyright © 2017, Texas Instruments Incorporated
Figure 104. Analog Window Comparator
8.2.1.1 Design Requirements
In many automotive sensor monitors there is a need to make a decision at the system-level when the input signal
crosses a predefined threshold. Analog window comparators are being used extensively in such applications.
An analog window comparator has a set of comparators. The external input signal is connected to the inverting
terminal of one comparator and the noninverting terminal of the other comparator. The remaining input of each
comparator is connected to the internal reference. The outputs are tied together and are often connected to a
reset or general-purpose input of a processor (such as a digital signal processor, field-programmable gate array,
or application-specific integrated circuit) or the enable input of a voltage regulator (such as a DC-DC or lowdropout regulator). Figure 104 shows the circuit diagram for an analog window comparator.
Though analog comparators are easy to design, there are certain disadvantages associated with analog
comparators.
• Higher Power Consumption: If the voltage that is monitored is greater than the window comparator supply
voltage, then there is a need for a resistive divider ladder to scale down that voltage. This resistive ladder
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
59
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Typical Applications (continued)
•
draws a constant current and adds to the power consumption of the system. In battery powered applications,
this becomes a challenge and can adversely affect the battery life.
Fixed Threshold Voltages: The window comparator thresholds cannot be changed on-the-fly since these are
set by hardware (typically with a resistive ladder). This may add a limitation if user wants to change the
comparator thresholds during operation without switching in a new resistor ladder.
Automotive systems often require a device which monitors either critical voltage rails, temperature of the critical
blocks or sensors and gives an alert/interrupt to the host MCU only when the input that being monitored falls
crosses a predefined, programmable threshold. The ADS7142-Q1 is an excellent fit for such system level
monitoring due to its ability to autonomously monitor sensor output and wake up the host controller whenever the
sensor output crosses pre-defined thresholds. Additionally, the ADS7142-Q1 has an internal data buffer which
can store 16 sample data which the user can read in case further analysis is required. Figure 105 shows typical
block diagram of ADS7142-Q1 as sensor monitor. As is shown in this figure, the sensor can be connected
directly to the input of the ADC (depending on the sensor output signal characteristics).
3V3
+
RFLT
SCL
Sensor 1
GND
C
AIN0
GND
ADS7142-Q1
AIN1
RFLT
SDA
Host MCU
ALERT
+
BUSY/RDY
C
Sensor 2
GND
GND
GND
GND
Figure 105. Sensor Monitor Circuit with ADS7142-Q1
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Programmable Thresholds and Hysteresis
The ADS7142-Q1 can be programmed to monitor sensor output voltages and generate an ALERT signal for the
host controller if the sensor output voltage crosses a threshold.
The device can be configured to monitor for signals rising above a programmed threshold. Figure 106 illustrates
the operation of the device when monitoring for signal crossings on the low threshold by setting the high
threshold to 0xFFF. In this case, the output of the low-side comparator is set whenever the ADC conversion
result is less than or equal to the low threshold, and the output of the high-side comparator is only set when the
ADC conversion result is equal to 0xFFF.
The device can also be configured to monitor for signals falling below a programmed threshold. Figure 107
illustrates the operation of the device when monitoring for signal crossings on the high threshold by setting the
low threshold to 0x000. In this case, the output of high-side comparator is set whenever the ADC conversion
result is greater than or equal to the high threshold and the output of the low-side comparator will only be set
when the ADC conversion result is equal to 0x000.
60
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Typical Applications (continued)
High Threshold = 0xFFF
Hysteresis
PRE_ALT_MAX_EVENT_COUNT = 50h
Conversion [N+9] for CHx
±
High Threshold - Hysteresis
+
Conversion [N+4] for CHx
High Side Comparator
Conversion [N] for CHx
Hysteresis
High Threshold
High Threshold - Hysteresis
Low Threshold + Hysteresis
±
+
Low Side Comparator
±
High Side Comparator
+
Conversion [N+5] for CHx
High Side Comparator Output
(Internal Signal Only)
Low Threshold
Conversion [N+10] for CHx
PRE_ALT_MAX_EVENT_COUNT = 50h
Low Threshold + Hysteresis
Low Side Comparator
±
+
Conversion [N] for CHx
Low Threshold = 0x000
Low Side Comparator Output
(Internal Signal Only)
Low Side Comparator Output
(Internal Signal Only)
ALERT
High Side Comparator Output
(Internal Signal Only)
Figure 106. Low Alert with ADS7142-Q1
ALERT
Figure 107. High Alert with ADS7142-Q1
The device can also be configured to monitor for signals falling outside of a programmed window. Figure 108
illustrates the operation of the device for an out-of-range alert where the signal leaves the pre-defined window
and crosses either the high or low threshold. In this case, the output of low side comparator is set whenever the
ADC conversion result is less than or equal to the low threshold, and the output of high side comparator is set
when the ADC conversion result is greater than or equal to the high threshold.
PRE_ALT_MAX_EVENT_COUNT = 50h
Conversion [N+12] for CHx
Conversion [N+7] for CHx
Hysteresis
High Threshold
High Threshold - Hysteresis
±
+
High Side Comparator
Low Threshold + Hysteresis
Low Side Comparator
±
+
Conversion [N] for CHx
Low Threshold
Low Side Comparator Output
(Internal Signal Only)
High Side Comparator Output
(Internal Signal Only)
ALERT
Figure 108. Out of Range Alert with ADS7142-Q1
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
61
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Typical Applications (continued)
8.2.1.2.2 False Trigger Prevention with Event Counter
The Pre-Alert event counter in the Digital Window Comparator helps to prevent false triggers. The alert output is
not set until the output of the comparator remains set for a pre-defined number (count) of consecutive
conversions.
8.2.1.2.3 Fault Diagnostics with Data Buffer
The modes which are specifically designed for autonomous sensor monitor applications are Pre-Alert mode and
Post-Alert mode. In Pre-Alert mode, the ADS7142-Q1 can be configured to monitor sensor outputs and
continuously fill the internal data buffer until a threshold crossing occurs. The ADS7142-Q1 will generate an
ALERT signal when the sensor output falls outside of the predefined window of operation. In this particular mode,
the ADS7142-Q1 stops filling the data buffer when the threshold is crossed and provides the last 16 samples (15
sample data preceding the sample at which the ALERT is generated and 1 sample data for which the ALERT is
generated). Figure 109 shows the ADS7142-Q1 operation in Pre-Alert mode showing 16 data samples before the
sensor output crosses the low threshold. This is useful for applications where the state of the signal before the
threshold is crossed is important to capture. Using the data captured before the alert, deep data analysis can be
performed to determine the state of the system before the alert. This type of data is not available with analog
comparators.
In Post-Alert mode, ADS7142-Q1 can be configured to monitor sensor outputs and start filling the internal data
buffer after a threshold crossing occurs. The ADS7142-Q1 generates an ALERT signal when the sensor output
falls outside of the predefined window of operation. In this particular mode, the ADS7142-Q1 continues to fill the
data buffer after the threshold is crossed for a total of 16 samples (1 sample data for which ALERT is generated
and 15 sample data after the sample at which ALERT is generated). Figure 110 shows the ADS7142-Q1
operation in Post-Alert mode showing 16 data samples after the sensor output crosses the high threshold. This is
useful for applications where the state of the signal after the threshold is crossed is important to capture. Using
the data captured after the alert, deep data analysis can be performed for to determine the state of the system
after the alert to detect system-level events such as saturation. This data is not available with analog
comparators.
62
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Typical Applications (continued)
8.2.1.3 Application Curves
Figure 109. Pre-Alert Data Capture
Figure 110. Post Alert Data Capture
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
63
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
Typical Applications (continued)
8.2.2 Voltage and Temperature Monitoring in Remote Camera Modules Using the ADS7142-Q1
CO-AXIAL CABLE
IMAGER
NTC
ADS7142-Q1
I2C
FPD
LINK
FPD
LINK
Serializer
De-Serializer
DC-DC
OR
LDO
DC/DC
OR
LDO
I2C
HOST
CONTROLLER
(Image
Processing)
VBAT
Figure 111. Voltage and Temperature Sensing in Remote Camera Modules Using the ADS7142-Q1
8.2.2.1 Design Requirements
Camera modules are an integral part of advanced driver assistance systems (ADAS), which are designed to
make cars safer. Automotive cameras and camera modules are often assist in blind spot detection, nap
prevention, lane and border detection, surround view and parking. Based on application, there are multiple types
of camera modules available such as front camera, rear camera, night vision camera. Figure 111 shows the
typical block diagram of camera module used in an automotive environment with key electronics building blocks
in the system.
The camera module is usually situated externally at front, back or either side of the vehicle. Many times the main
controller that does the data processing can not be used on camera module side due to size constraints. The
camera module unit communicates with central processor over co-axial cable. The camera module data is
transmitted over co-axial cable using a serializer. On data processing unit, De-serializer is used to communicate
this data with host processor. The power to the camera module is also transmitted over co-axial cable. As the
camera module is remotely placed and power is transferred over co-axial cable which can be few meters long,
voltage received by camera module and critical voltage rails powering image sensors are often monitored against
permissible variations. Also the difference between camera lens and external ambient temperature can introduce
dampness and degrade video quality. To ensure optimal video quality camera lens temperature is often
monitored for any possible correction. The device monitoring these system level parameters has to be small size
due to limited board space available on the camera module side. Also I2C interface is preferred as it enables
user to connect multiple monitoring and sensing devices on the same I2C bus. ADS7142-Q1 small footprint (2mm
x3mm, QFN package) and its I2C interface capable of working over wide digital I/O voltages enable this device in
camera module monitoring application without demanding extra board space.
64
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
9 Power Supply Recommendations
9.1 AVDD and DVDD Supply Recommendations
The ADS7142-Q1 has two separate power supplies: AVDD and DVDD. The device operates on AVDD; DVDD is
used for the interface circuits. AVDD and DVDD can be independently set to any value within the permissible
ranges. The AVDD supply also defines the full-scale input range of the device. Always set the AVDD supply to
be greater than or equal to the maximum input signal to avoid saturation of codes. Decouple the AVDD and
DVDD pins respectively with CAVDD = 220 nF and CDVDD = 100 nF ceramic decoupling capacitors, as shown in
Figure 112.
AVDD
CAVDD
GND
CDVDD
DVDD
Copyright © 2016, Texas Instruments Incorporated
Figure 112. Power-Supply Decoupling
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
65
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
10 Layout
10.1 Layout Guidelines
•
•
Use a solid ground plane underneath the device and partition the PCB into analog and digital sections.
Avoid crossing digital lines with the analog signal path and keep the analog input signals and the reference
input signals away from noise sources.
The power sources to the device must be clean and well-bypassed. Use CAVDD decoupling capacitors in close
proximity to the analog (AVDD) power supply pin.
Use a CDVDD decoupling capacitor close to the digital (DVDD) power-supply pin.
Avoid placing vias between the AVDD and DVDD pins and the bypass capacitors.
Connect the ground pin to the ground plane using a short, low-impedance path. Thermal pad should also be
connected to the ground plane.
Place the charge kickback filter components close to the device.
•
•
•
•
•
Among ceramic surface-mount capacitors, COG (NPO) ceramic capacitors are recommended because these
components provide the most stable electrical properties over voltage, frequency, and temperature changes.
Figure 113 shows the typical connection diagram of ADS7142-Q1.
CDVDD
ADS7142-Q1
1
GND
DVDD
10
RSDA
AVDD
SCL
9
3
AINP/AIN0
SDA
8
To I2C Master or Host
4
AINM/AIN1
ALERT
7
To I2C Master or Host
5
ADDR
BUSY/RDY
6
2
From Sensor
Output
From Sensor
Output
RFLT1
RALERT
RSCL
CAVDD
To I2C Master or Host
CFLT0
CFLT1
RADDR1
To I2C Master or Host
AVDD
RADDR2
PAD
Figure 113. Example Schematic
66
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
10.2 Layout Example
Figure 114. Example Layout
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
67
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
www.ti.com
11 Device and Documentation Support
11.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.2 Community Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
68
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
69
ADS7142-Q1
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
70
Submit Documentation Feedback
www.ti.com
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
ADS7142-Q1
www.ti.com
SBAS891A – NOVEMBER 2018 – REVISED OCTOBER 2019
Submit Documentation Feedback
Copyright © 2018–2019, Texas Instruments Incorporated
Product Folder Links: ADS7142-Q1
71
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jan-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ADS7142QDQCRQ1
ACTIVE
WSON
DQC
10
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
1AU
ADS7142QDQCTQ1
PREVIEW
WSON
DQC
10
250
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
1AU
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jan-2020
OTHER QUALIFIED VERSIONS OF ADS7142-Q1 :
• Catalog: ADS7142
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Jan-2020
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
ADS7142QDQCRQ1
Package Package Pins
Type Drawing
WSON
DQC
10
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
3000
179.0
8.4
Pack Materials-Page 1
2.3
B0
(mm)
K0
(mm)
P1
(mm)
3.2
1.0
4.0
W
Pin1
(mm) Quadrant
8.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Jan-2020
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS7142QDQCRQ1
WSON
DQC
10
3000
195.0
200.0
45.0
Pack Materials-Page 2
PACKAGE OUTLINE
DQC0010B
WSON - 0.8mm max height
SCALE 4.500
PLASTIC SMALL OUTLINE - NO LEAD
2.1
1.9
B
A
0.1 MIN
(0.05)
PIN 1 INDEX AREA
SECTION A-A
A-A30.000
TYPICAL
3.1
2.9
0.3
0.2
0.35
0.25
OPTIONAL TERMINAL
TYPICAL
C
0.8 MAX
SEATING PLANE
0.08
(0.2) TYP
0.84 0.1
0.05
0.00
SYMM
5
A
6
A
8X 0.5
2.4 0.1
2X
2
11
SYMM
SEE OPTIONAL
TERMINAL
DETAIL
1
10
10X
PIN 1 ID
(45 X0.2)
10X
0.35
0.25
0.3
0.2
0.1
0.05
C A B
C
4224405/A
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
06/2018
EXAMPLE BOARD LAYOUT
DQC0010B
WSON - 0.8mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(0.84)
( 0.2) TYP
VIA
10X (0.5)
1
10
10X (0.25)
(0.95)
11
SYMM
(2.4)
8X (0.5)
6
5
(R0.05) TYP
SYMM
(1.9)
LAND PATTERN EXAMPLE
SCALE: 30X
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
METAL
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4224405/A
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
06/2018
EXAMPLE STENCIL DESIGN
DQC0010B
WSON - 0.8mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(0.8)
10X (0.5)
10X (0.25)
10
1
(1.08)
11
SYMM
8X (0.5)
(0.64)
METAL
TYP
6
5
(R0.05) TYP
SYMM
(1.9)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD 11:
86% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
SCALE: 30X
4224405/A
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
06/2018
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising