Texas Instruments | 14-Bit, 10MHz CCD/CIS Signal Processor (Rev. A) | Datasheet | Texas Instruments 14-Bit, 10MHz CCD/CIS Signal Processor (Rev. A) Datasheet

Texas Instruments 14-Bit, 10MHz CCD/CIS Signal Processor (Rev. A) Datasheet
Not Recommended For New Designs
VSP3100
®
VSP
310
0
For most current data sheet and other product
information, visit www.burr-brown.com
14-Bit, 10MHz
CCD/CIS SIGNAL PROCESSOR
FEATURES
DESCRIPTION
● INTEGRATED TRIPLE-CORRELATED
DOUBLE SAMPLER
● OPERATION MODE SELECTABLE:
1-Channel, 3-Channel, 10MSPS (typ),
CCD/CIS Mode
● PROGRAMMABLE GAIN AMPLIFIER:
0dB to +13dB
● SELECTABLE OUTPUT MODES:
Normal/Demultiplexed
● OFFSET CONTROL RANGE: ±400mV
● +3V, +5V Digital Output
● LOW POWER: 450mW (typ)
The VSP3100 is a complete CCD/CIS image processor which operates from a single +5V supply.
This complete image processor includes three Correlated Double Samplers (CDS) and Programmable Gain
Amplifiers (PGA) to process CCD signals.
These three channel inputs also allow Contact Image
Sensor (CIS) inputs.
The VSP3100 is an interface compatible with the
VSP3000 which is 12-bit one-chip product.
The VSP3100 can be operated from 0°C to +85°C and
is available in an LQFP-48 package.
● LQFP-48 SURFACE-MOUNT PACKAGE
CLP
CK1 CK2
ADCCK
TP0
VREF
Reference
Circuit
CM
Timing Generator
Clamp
REFP
RINP
CDS
PGA
REFN
INN
10
5
10-Bit
DAC
OE
VDRV
Clamp
GINP
CDS
10
PGA
14-Bit
A/D
MUX
14
Digital
Output
Control
B0-B13
(A0-A2, D0-D9)
5
10-Bit
DAC
Clamp
BINP
CDS
Offset
Register
R
G
10
PGA
3
Gain
Control
Register
10-Bit
DAC
R
Configuration
Register
5
8
10
P/S
G
B
Register
Port
WRT
B
RD
5
SCLK
SD
VSP3100
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
© 2000 Burr-Brown Corporation
SBMS007
PDS-1583A
Printed in U.S.A. April, 2000
PACKAGE OPTION ADDENDUM
www.ti.com
24-Aug-2018
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
VSP3100Y
NRND
LQFP
PT
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 85
VSP3100Y
VSP3100Y/2K
NRND
LQFP
PT
48
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 85
VSP3100Y
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
24-Aug-2018
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Sep-2019
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
VSP3100Y/2K
Package Package Pins
Type Drawing
LQFP
PT
48
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
17.4
Pack Materials-Page 1
9.5
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
9.5
2.0
12.0
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Sep-2019
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
VSP3100Y/2K
LQFP
PT
48
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising