Texas Instruments | VSP2101 SpeedPlus™ CCD Signal Processor For Digital Cameras (Rev. A) | Datasheet | Texas Instruments VSP2101 SpeedPlus™ CCD Signal Processor For Digital Cameras (Rev. A) Datasheet

Texas Instruments VSP2101 SpeedPlus™ CCD Signal Processor For Digital Cameras (Rev. A) Datasheet
Not Recommended For New Designs
VSP2101
®
VSP
210
1
CCD SIGNAL PROCESSOR
For Digital Cameras
TM
FEATURES
DESCRIPTION
● CCD SIGNAL PROCESSING:
Correlated Double Sampling
Black Level Clamping
–2 to +34dB Gain Ranging
High SNR: 53dB
The VSP2101Y is a complete digital camera IC, providing signal conditioning and 10-bit analog-to-digital
conversion for the output of a CCD array.
The primary CCD channel provides correlated double
sampling to extract the video information from the
pixels, –2dB to +34dB gain ranging with digital control for varying illumination conditions, and black
level clamping for an accurate black reference.
● 10-BIT A/D CONVERSION:
Up to 27MHz Conversion Rate
No Missing Codes
● PORTABLE OPERATION:
Low Voltage: 2.7V to 3.6V
Low Power: 190mW at 3.0V
● LOW POWER: 160mW at 2.7V
● POWER-DOWN MODE: 18mW
Input signal clamping and offset correction of the CDS
is also performed. The stable gain control is linear in
dB. Additionally, the black level is quickly recovered
after gain change. An on-chip general purpose 10-bit
digital-to-analog converter allows you to obtain analog control voltage for iris control.
The VSP2101Y is available in a 48-lead LQFP package and operates from a single +3V supply.
APPLICATIONS
●
●
●
●
VIDEO CAMERAS
DIGITAL STILL CAMERAS
PC CAMERAS
SECURITY CAMERAS
REFCK DATCK
WRT SD SCLK
OB
DAC OUT
ADCK
DRVDD
C
10-Bit
D/A Converter
(DAC1)
Serial Port
Register
A/D
Timing Control
10-Bit
D/A Converter
(DAC0)
CCD D
Correlated
Double
Sampling
Black Level
Auto-Zero
Log VCA
+6dB
+28dB
10-Bit
A/D
Converter
Output
Latch
10-Bit
Digital
Output
CCD Out
Clamp
CCD R
Dummy
Pixel
Auto- Zero
A/D
Reference
DUMC
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
©
SBMS005
1998 Burr-Brown Corporation
PDS-1506B
Printed in U.S.A. June, 1999
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2019
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
VSP2101Y
ACTIVE
LQFP
PT
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
VSP2101Y
VSP2101YG4
ACTIVE
LQFP
PT
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
VSP2101Y
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2019
Addendum-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising