Texas Instruments | ADC084S101 4 Channel, 500 ksps to 1 Msps, 8-Bit A/D Converter (Rev. D) | Datasheet | Texas Instruments ADC084S101 4 Channel, 500 ksps to 1 Msps, 8-Bit A/D Converter (Rev. D) Datasheet

Texas Instruments ADC084S101 4 Channel, 500 ksps to 1 Msps, 8-Bit A/D Converter (Rev. D) Datasheet
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
ADC084S101 4 Channel, 500 ksps to 1 Msps, 8-Bit A/D Converter
Check for Samples: ADC084S101
FEATURES
DESCRIPTION
•
•
•
•
The ADC084S101 is a low-power, four-channel
CMOS 8-bit analog-to-digital converter with a highspeed serial interface. Unlike the conventional
practice of specifying performance at a single sample
rate only, the ADC084S101 is fully specified over a
sample rate range of 500 ksps to 1 Msps. The
converter is based on a successive-approximation
register architecture with an internal track-and-hold
circuit. It can be configured to accept up to four input
signals at inputs IN1 through IN4.
1
2
Specified Over a Range of Sample Rates
Four Input Channels
Variable Power Management
Single Power Supply with 2.7V - 5.25V Range
KEY SPECIFICATIONS
•
•
•
•
DNL: ±0.10 LSB (Typ)
INL: ± 0.13 LSB (Typ)
SNR: 49.6 dB (Typ)
Power Consumption:
– 3V Supply: 3.2 mW (Typ)
– 5V Supply: 9.6 mW (Typ)
The output serial data is straight binary, and is
compatible with several standards, such as SPI™,
QSPI™, MICROWIRE and many common DSP serial
interfaces.
The ADC084S101 operates with a single supply, that
can range from +2.7V to +5.25V. Normal power
consumption using a +3V or +5V supply is 3.2 mW
and 9.6 mW, respectively. The power-down feature
reduces the power consumption to just 0.12 µW using
a +3V supply, or 0.35 µW using a +5V supply.
APPLICATIONS
•
•
•
Portable Systems
Remote Data Acquisition
Instrumentation and Control Systems
The ADC084S101 is packaged in a 10-lead VSSOP
package. Operation over the industrial temperature
range of −40°C to +85°C is ensured.
Table 1. Pin-Compatible Alternatives by Resolution and Speed (1)
Resolution
(1)
Specified for Sample Rate Range of:
50 to 200 ksps
200 to 500 ksps
500 ksps to 1 Msps
12-bit
ADC124S021
ADC124S051
ADC124S101
10-bit
ADC104S021
ADC104S051
ADC104S101
8-bit
ADC084S021
ADC084S051
ADC084S101
All devices are fully pin and function compatible.
Connection Diagram
CS
1
10
SCLK
VA
2
9
DOUT
GND
3
8
DIN
IN4
4
7
IN1
IN3
5
6
IN2
ADC084S101
Figure 1. 10-Lead VSSOP
See DGS Package
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2013, Texas Instruments Incorporated
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
Block Diagram
IN1
.
.
.
MUX
T/H
8-Bit
SUCCESSIVE
APPROXIMATION
ADC
VA
GND
GND
IN4
SCLK
CONTROL
LOGIC
CS
DIN
DOUT
PIN DESCRIPTIONS and EQUIVALENT CIRCUITS
Pin No.
Symbol
Description
ANALOG I/O
4-7
IN1 to IN4
Analog inputs. These signals can range from 0V to VA.
DIGITAL I/O
10
SCLK
Digital clock input. This clock directly controls the conversion and readout processes.
9
DOUT
Digital data output. The output samples are clocked out of this pin on falling edges of the
SCLK pin.
8
DIN
Digital data input. The ADC084S101's Control Register is loaded through this pin on rising
edges of the SCLK pin.
1
CS
Chip select. On the falling edge of CS, a conversion process begins. Conversions continue
as long as CS is held low.
2
VA
Positive supply pin. This pin should be connected to a quiet +2.7V to +5.25V source and
bypassed to GND with a 1 µF capacitor and a 0.1 µF monolithic capacitor located within 1
cm of the power pin.
3
GND
POWER SUPPLY
2
The ground return for supply and signals.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2) (3)
−0.3V to 6.5V
Supply Voltage VA
−0.3V to VA +0.3V
Voltage on Any Pin to GND
Input Current at Any Pin (4)
Package Input Current
±10 mA
(4)
±20 mA
See (5)
Power Consumption at TA = 25°C
Human Body Model
ESD Susceptibility (6)
2500V
Machine Model
250V
Junction Temperature
+150°C
Storage Temperature
−65°C to +150°C
(1)
(2)
(3)
(4)
(5)
(6)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For guaranteed specifications and test conditions, see the
Electrical Characteristics. The specified specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
All voltages are measured with respect to GND = 0V, unless otherwise specified.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
When the input voltage at any pin exceeds the power supply (that is, VIN < GND or VIN > VA), the current at that pin should be limited to
10 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an
input current of 10 mA to two. The Absolute Maximum Rating specification does not apply to the VA pin. The current into the VA pin is
limited by the Analog Supply Voltage specification.
The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by
TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula
PDMAX = (TJmax − TA)/θJA. The values for maximum power dissipation listed above will be reached only when the device is operated in
a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is
reversed). Obviously, such conditions should always be avoided.
Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through zero ohms.
Operating Ratings (1) (2)
−40°C ≤ TA ≤ +85°C
Operating Temperature Range
VA Supply Voltage
+2.7V to +5.25V
−0.3V to VA
Digital Input Pins Voltage Range
Clock Frequency
50 kHz to 16 MHz
Analog Input Voltage
(1)
(2)
0V to VA
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For guaranteed specifications and test conditions, see the
Electrical Characteristics. The specified specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
All voltages are measured with respect to GND = 0V, unless otherwise specified.
Package Thermal Resistance (1)
(1)
Package
θJA
10-lead VSSOP
190°C / W
Soldering process must comply with Reflow Temperature Profile specifications. Refer to www.ti.com/packaging. Reflow temperature
profiles are different for lead-free and non-lead-free packages.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
3
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
ADC084S101 Converter Electrical Characteristics (1)
The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 8 MHz to 16 MHz, fSAMPLE = 500 ksps to 1
Msps, CL = 50 pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.
Symbol
Parameter
Conditions
Typical
Limits (2)
8
Bits
±0.13
±0.4
LSB (max)
Units
STATIC CONVERTER CHARACTERISTICS
Resolution with No Missing Codes
INL
Integral Non-Linearity
DNL
Differential Non-Linearity
±0.10
±0.4
LSB (max)
VOFF
Offset Error
+0.53
±0.7
LSB (max)
OEM
Channel to Channel Offset Error Match
0.005
±0.3
LSB (max)
FSE
Full Scale Error
0.52
±0.7
LSB (max)
FSEM
Channel to Channel Full Scale Error Match
0.005
±0.3
LSB (max)
DYNAMIC CONVERTER CHARACTERISTICS
SINAD
Signal-to-Noise Plus Distortion Ratio
VA = +2.7V to 5.25V
fIN = 40.3 kHz, −0.02 dBFS
49.6
49.1
dB (min)
SNR
Signal-to-Noise Ratio
VA = +2.7V to 5.25V
fIN = 40.3 kHz, −0.02 dBFS
49.6
49.2
dB (min)
THD
Total Harmonic Distortion
VA = +2.7V to 5.25V
fIN = 40.3 kHz, −0.02 dBFS
−75
−62
dB (max)
SFDR
Spurious-Free Dynamic Range
VA = +2.7V to 5.25V
fIN = 40.3 kHz, −0.02 dBFS
67
63
dB (min)
ENOB
Effective Number of Bits
VA = +2.7V to 5.25V
fIN = 40.3 kHz, −0.02 dBFS
7.9
7.9
Bits (min)
Channel-to-Channel Crosstalk
VA = +5.25V
fIN = 40.3 kHz
−73
dB
Intermodulation Distortion, Second Order
Terms
VA = +5.25V
fa = 40.161 kHz, fb = 41.015 kHz
−78
dB
Intermodulation Distortion, Third Order
Terms
VA = +5.25V
fa = 40.161 kHz, fb = 41.015 kHz
−73
dB
VA = +5V
11
MHz
VA = +3V
8
MHz
0 to VA
V
IMD
FPBW
-3 dB Full Power Bandwidth
ANALOG INPUT CHARACTERISTICS
VIN
Input Range
IDCL
DC Leakage Current
CINA
Input Capacitance
±1
µA (max)
Track Mode
33
pF
Hold Mode
3
pF
DIGITAL INPUT CHARACTERISTICS
VIH
Input High Voltage
VIL
Input Low Voltage
IIN
Input Current
CIND
Digital Input Capacitance
VA = +5.25V
2.4
VA = +3.6V
2.1
V (min)
0.8
V (max)
VIN = 0V or VA
V (min)
±10
µA (max)
2
4
pF (max)
ISOURCE = 200 µA
VA − 0.03
VA − 0.5
V (min)
ISOURCE = 1 mA
VA − 0.1
ISINK = 200 µA
0.03
0.4
V (max)
ISINK = 1 mA
0.1
DIGITAL OUTPUT CHARACTERISTICS
VOH
Output High Voltage
VOL
Output Low Voltage
IOZH, IOZL TRI-STATE Leakage Current
COUT
TRI-STATE Output Capacitance
Output Coding
(1)
(2)
4
V
V
±0.01
±1
µA (max)
2
4
pF (max)
Straight (Natural) Binary
Min/max specification limits are specified by design, test, or statistical analysis.
Tested limits are ensured to AOQL (Average Outgoing Quality Level).
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
ADC084S101 Converter Electrical Characteristics(1) (continued)
The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 8 MHz to 16 MHz, fSAMPLE = 500 ksps to 1
Msps, CL = 50 pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.
Symbol
Parameter
Conditions
Typical
Limits (2)
Units
POWER SUPPLY CHARACTERISTICS (CL = 10 pF)
VA
Supply Voltage
Supply Current, Normal Mode (Operational,
CS low)
IA
Supply Current, Shutdown (CS high)
Power Consumption, Normal Mode
(Operational, CS low)
PD
Power Consumption, Shutdown (CS high)
2.7
V (min)
5.25
V (max)
VA = +5.25V,
fSAMPLE = 1 Msps, fIN = 40 kHz
1.82
2.4
mA (max)
VA = +3.6V,
fSAMPLE = 1 Msps, fIN = 40 kHz
0.9
1.2
mA (max)
VA = +5.25V,
fSAMPLE = 0 ksps
200
nA
VA = +3.6V,
fSAMPLE = 0 ksps
200
nA
VA = +5.25V
9.6
12.6
mW (max)
VA = +3.6V
3.2
4.3
mW (max)
VA = +5.25V
0.35
µW
VA = +3.6V
0.12
µW
AC ELECTRICAL CHARACTERISTICS
8
MHz (min)
16
MHz (max)
500
ksps (min)
fSCLK
Clock Frequency
See (3)
fS
Sample Rate
See (3)
tCONV
Conversion Time
DC
SCLK Duty Cycle
fSCLK = 16 MHz
70
% (max)
tACQ
Track/Hold Acquisition Time
Full-Scale Step Input
3
SCLK cycles
Throughput Time
Acquisition Time + Conversion Time
16
SCLK cycles
(3)
50
1
Msps (max)
13
SCLK cycles
30
% (min)
This is the frequency range over which the electrical performance is ensured. The device is functional over a wider range which is
specified under Operating Ratings.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
5
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
ADC084S101 Timing Specifications
The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 8 MHz to 16 MHz, fSAMPLE = 500 ksps to 1
Msps, CL = 50 pF, Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.
Symbol
Parameter
Conditions
−3.5
VA = +5.0V
−0.5
VA = +3.0V
+4.5
VA = +5.0V
+1.5
VA = +3.0V
+4
VA = +5.0V
+2
VA = +3.0V
+16.5
VA = +5.0V
+15
Units
10
ns (min)
10
ns (min)
30
ns (max)
30
ns (max)
Setup Time SCLK High to CS Falling Edge
See (2)
tCLH
Hold time SCLK Low to CS Falling Edge
See (2)
tEN
Delay from CS Until DOUT active
tACC
Data Access Time after SCLK Falling Edge
tSU
Data Setup Time Prior to SCLK Rising Edge
+3
10
ns (min)
tH
Data Valid SCLK Hold Time
+3
10
ns (min)
tCH
SCLK High Pulse Width
tCL
SCLK Low Pulse Width
Output Falling
CS Rising Edge to DOUT High-Impedance
Output Rising
6
VA = +3.0V
Limits (1)
tCSU
tDIS
(1)
(2)
Typical
0.5 x tSCLK 0.3 x tSCLK
ns (min)
0.5 x tSCLK 0.3 x tSCLK
ns (min)
VA = +3.0V
1.7
VA = +5.0V
1.2
VA = +3.0V
1.0
VA = +5.0V
1.0
20
ns (max)
Tested limits are ensured to AOQL (Average Outgoing Quality Level).
Clock may be either high or low when CS is asserted as long as setup and hold times tCSU and tCLH are strictly observed..
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
Timing Diagrams
Power Down
Power Up
Track
Power Up
Hold
Track
Hold
CS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
9
8
10
SCLK
Control register
Control register
DIN
b7
b6
b5
b4
DOUT
b3
b2
b1
DB7
DB6 DB5
b0
b7
DB4
DB3
DB2
DB1
b6
b5
b4
DB0
b3
b2
b1
b0
DB7
DB6
DB5
DB4
DB3
Figure 2. ADC084S101 Operational Timing Diagram
Figure 3. Timing Test Circuit
CS
tCONVERT
tACQ
tCH
SCLK
1
2
3
4
tEN
6
7
Z3
tSU
Z2
Z1
11
8
12
13
14
15
tACC
tCL
DOUT
DIN
5
DB7
Z0
DB6
16
tDIS
DB5
DB1
DB4
DB0
Tri-State
Zero
Zero
Zero
Zero
tH
DONT DONTC ADD2
ADD1
ADD0
DONTC DONTC DONTC
Figure 4. ADC084S101 Serial Timing Diagram
CS
tCSU
SCLK
tCLH
SCLK
Figure 5. SCLK and CS Timing Parameters
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
7
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
Specification Definitions
ACQUISITION TIME is the time required to acquire the input voltage. That is, it is time required for the hold
capacitor to charge up to the input voltage.
APERTURE DELAY is the time between the fourth falling SCLK edge of a conversion and the time when the
input signal is acquired or held for conversion.
CONVERSION TIME is the time required, after the input voltage is acquired, for the ADC to convert the input
voltage to a digital word.
CROSSTALK is the coupling of energy from one channel into the other channel, or the amount of signal energy
from one analog input that appears at the measured analog input.
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1
LSB.
DUTY CYCLE is the ratio of the time that a repetitive digital waveform is high to the total time of one period. The
specification here refers to the SCLK.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise
and Distortion or SINAD. ENOB is defined as (SINAD − 1.76) / 6.02 and says that the converter is equivalent to
a perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental
drops 3 dB below its low frequency value for a full scale input.
FULL SCALE ERROR (FSE) is a measure of how far the last code transition is from the ideal 1½ LSB below
VREF+ and is defined as:
VFSE = Vmax + 1.5 LSB – VREF+
where
•
GAIN ERROR is the deviation of the last code transition (111...110) to (111...111) from the ideal (VREF − 1.5
LSB), after adjusting for offset error.
(1)
INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from
negative full scale (½ LSB below the first code transition) through positive full scale (½ LSB above the last code
transition). The deviation of any given code from this straight line is measured from the center of that code value.
INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two
sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in
the second and third order intermodulation products to the sum of the power in both of the original frequencies.
IMD is usually expressed in dB.
MISSING CODES are those output codes that will never appear at the ADC outputs. These codes cannot be
reached with any input value. The ADC084S101 is ensured not to have any missing codes.
OFFSET ERROR is the deviation of the first code transition (000...000) to (000...001) from the ideal (i.e. GND +
0.5 LSB).
SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms
value of the sum of all other spectral components below one-half the sampling frequency, not including
harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the
input signal to the rms value of all of the other spectral components below half the clock frequency, including
harmonics but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the
input signal and the peak spurious signal where a spurious signal is any signal present in the output spectrum
that is not present at the input, excluding d.c.
8
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB or dBc, of the rms total of the first five
harmonic components at the output to the rms level of the input signal frequency as seen at the output. THD is
calculated as
THD = 20 ‡ log10
A f 22 +
+ A f 62
A f12
where
•
Af1 is the RMS power of the input frequency at the output and Af2 through Af6 are the RMS power in the first 5
harmonic frequencies.
(2)
THROUGHPUT TIME is the minimum time required between the start of two successive conversion. It is the
acquisition time plus the conversion and read out times. In the case of the ADC084S101, this is 16 SCLK
periods.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
9
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
TA = +25°C, fSAMPLE = 500 ksps to 1 Msps, fSCLK = 8 MHz to 16 MHz, fIN = 40.3 kHz unless otherwise stated.
10
DNL - VA = 3.0V
INL - VA = 3.0V
Figure 6.
Figure 7.
DNL - VA = 5.0V
INL - VA = 5.0V
Figure 8.
Figure 9.
DNL vs. Supply
INL vs. Supply
Figure 10.
Figure 11.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
TA = +25°C, fSAMPLE = 500 ksps to 1 Msps, fSCLK = 8 MHz to 16 MHz, fIN = 40.3 kHz unless otherwise stated.
DNL vs. Clock Frequency
INL vs. Clock Frequency
Figure 12.
Figure 13.
DNL vs. Clock Duty Cycle
INL vs. Clock Duty Cycle
Figure 14.
Figure 15.
DNL vs. Temperature
INL vs. Temperature
Figure 16.
Figure 17.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
11
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
TA = +25°C, fSAMPLE = 500 ksps to 1 Msps, fSCLK = 8 MHz to 16 MHz, fIN = 40.3 kHz unless otherwise stated.
12
SNR vs. Supply
THD vs. Supply
Figure 18.
Figure 19.
SNR vs. Clock Frequency
THD vs. Clock Frequency
Figure 20.
Figure 21.
SNR vs. Clock Duty Cycle
THD vs. Clock Duty Cycle
Figure 22.
Figure 23.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
TA = +25°C, fSAMPLE = 500 ksps to 1 Msps, fSCLK = 8 MHz to 16 MHz, fIN = 40.3 kHz unless otherwise stated.
SNR vs. Input Frequency
THD vs. Input Frequency
Figure 24.
Figure 25.
SNR vs. Temperature
THD vs. Temperature
Figure 26.
Figure 27.
SFDR vs. Supply
SINAD vs. Supply
Figure 28.
Figure 29.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
13
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
TA = +25°C, fSAMPLE = 500 ksps to 1 Msps, fSCLK = 8 MHz to 16 MHz, fIN = 40.3 kHz unless otherwise stated.
14
SFDR vs. Clock Frequency
SINAD vs. Clock Frequency
Figure 30.
Figure 31.
SFDR vs. Clock Duty Cycle
SINAD vs. Clock Duty Cycle
Figure 32.
Figure 33.
SFDR vs. Input Frequency
SINAD vs. Input Frequency
Figure 34.
Figure 35.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
TA = +25°C, fSAMPLE = 500 ksps to 1 Msps, fSCLK = 8 MHz to 16 MHz, fIN = 40.3 kHz unless otherwise stated.
SFDR vs. Temperature
SINAD vs. Temperature
Figure 36.
Figure 37.
ENOB vs. Supply
ENOB vs. Clock Frequency
Figure 38.
Figure 39.
ENOB vs. Clock Duty Cycle
ENOB vs. Input Frequency
Figure 40.
Figure 41.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
15
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
TA = +25°C, fSAMPLE = 500 ksps to 1 Msps, fSCLK = 8 MHz to 16 MHz, fIN = 40.3 kHz unless otherwise stated.
16
ENOB vs. Temperature
Spectral Response - 3V, 1 Msps
Figure 42.
Figure 43.
Spectral Response - 5V, 1 Msps
Spectral Response - 3V, 500 ksps
Figure 44.
Figure 45.
Spectral Response - 5V, 500 ksps
Power Consumption vs. Throughput
Figure 46.
Figure 47.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
APPLICATIONS INFORMATION
ADC084S101 OPERATION
The ADC084S101 is a successive-approximation analog-to-digital converter designed around a chargeredistribution digital-to-analog converter. Simplified schematics of the ADC084S101 in both track and hold modes
are shown in Figure 48 and Figure 49, respectively. In Figure 48, the ADC084S101 is in track mode: switch SW1
connects the sampling capacitor to one of four analog input channels through the multiplexer, and SW2 balances
the comparator inputs. The ADC084S101 is in this state for the first three SCLK cycles after CS is brought low.
Figure 49 shows the ADC084S101 in hold mode: switch SW1 connects the sampling capacitor to ground,
maintaining the sampled voltage, and switch SW2 unbalances the comparator. The control logic then instructs
the charge-redistribution DAC to add fixed amounts of charge to the sampling capacitor until the comparator is
balanced. When the comparator is balanced, the digital word supplied to the DAC is the digital representation of
the analog input voltage. The ADC084S101 is in this state for the fourth through sixteenth SCLK cycles after CS
is brought low.
The time when CS is low is considered a serial frame. Each of these frames should contain an integer multiple of
16 SCLK cycles, during which time a conversion is performed and clocked out at the DOUT pin and data is
clocked into the DIN pin to indicate the multiplexer address for the next conversion.
CHARGE
REDISTRIBUTION
DAC
IN1
MUX
SAMPLING
CAPACITOR
IN4
SW1
SW2
AGND
+
-
CONTROL
LOGIC
VA
2
Figure 48. ADC084S101 in Track Mode
CHARGE
REDISTRIBUTION
DAC
IN1
MUX
SAMPLING
CAPACITOR
IN4
SW1
SW2
AGND
+
-
CONTROL
LOGIC
VA
2
Figure 49. ADC084S101 in Hold Mode
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
17
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
USING THE ADC084S101
An ADC084S101 timing diagram and a serial interface timing diagram for the ADC084S101 are shown in the
Timing Diagrams section. CS is chip select, which initiates conversions and frames the serial data transfers.
SCLK (serial clock) controls both the conversion process and the timing of serial data. DOUT is the serial data
output pin, where a conversion result is sent as a serial data stream, MSB first. Data to be written to the
ADC084S101's Control Register is placed on DIN, the serial data input pin. New data is written to the ADC at
DIN with each conversion.
A serial frame is initiated on the falling edge of CS and ends on the rising edge of CS. Each frame must contain
an integer multiple of 16 rising SCLK edges. The ADC output data (DOUT) is in a high impedance state when
CS is high and is active when CS is low. Thus, CS acts as an output enable. Additionally, the device goes into a
power down state when CS is high, and also between continuous conversion cycles.
During the first 3 cycles of SCLK, the ADC is in the track mode, acquiring the input voltage. For the next 13
SCLK cycles the conversion is accomplished and the data is clocked out, MSB first, starting on the 5th clock. If
there is more than one conversion in a frame, the ADC will re-enter the track mode on the falling edge of SCLK
after the N*16th rising edge of SCLK, and re-enter the hold/convert mode on the N*16+4th falling edge of SCLK,
where "N" is an integer.
When CS is brought high, SCLK is internally gated off. If SCLK is stopped in the low state while CS is high, the
subsequent fall of CS will generate a falling edge of the internal version of SCLK, putting the ADC into the track
mode. This is seen by the ADC as the first falling edge of SCLK. If SCLK is stopped with SCLK high, the ADC
enters the track mode on the first falling edge of SCLK after the falling edge of CS.
During each conversion, data is clocked into the DIN pin on the first 8 rising edges of SCLK after the fall of CS.
For each conversion, it is necessary to clock in the data indicating the input that is selected for the conversion
after the current one. See Table 2, Table 3, and Table 4.
If CS and SCLK go low within the times defined by tCSU and tCLH, the rising edge of SCLK that begins clocking
data in at DIN may be one clock cycle later than expected. It is, therefore, best to strictly observe the minimum
tCSU and tCLH times given in the Timing Specifications.
There are no power-up delays or dummy conversions required with the ADC084S101. The ADC is able to
sample and convert an input to full conversion immediately following power up. The first conversion result after
power-up will be that of IN1.
Table 2. Control Register Bits
Bit 7 (MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DONTC
DONTC
ADD2
ADD1
ADD0
DONTC
DONTC
DONTC
Table 3. Control Register Bit Descriptions
Bit #:
Symbol:
7 - 6, 2 - 0
DONTC
5
ADD2
4
ADD1
3
ADD0
Description
Don't care. The value of these bits do not affect device operation.
These three bits determine which input channel will be sampled and converted in the next
track/hold cycle. The mapping between codes and channels is shown in Table 4.
Table 4. Input Channel Selection
18
ADD2
ADD1
ADD0
Input Channel
x
0
0
IN1 (Default)
x
0
1
IN2
x
1
0
IN3
x
1
1
IN4
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
ADC084S101 TRANSFER FUNCTION
The output format of the ADC084S101 is straight binary. Code transitions occur midway between successive
integer LSB values. The LSB width for the ADC084S101 is VA/256. The ideal transfer characteristic is shown in
Figure 50. The transition from an output code of 0000 0000 to a code of 0000 0001 is at 1/2 LSB, or a voltage of
VA/512. Other code transitions occur at steps of one LSB.
111...111
111...000
|
|
ADC CODE
111...110
1LSB = VA/256
011...111
000...010
|
000...001
000...000
0V
+VA - 1 LSB
1 LSB
ANALOG INPUT
Figure 50. Ideal Transfer Characteristic
TYPICAL APPLICATION CIRCUIT
A typical application of the ADC084S101 is shown in Figure 51. Power is provided in this example by the Texas
Instruments LP2950 low-dropout voltage regulator, available in a variety of fixed and adjustable output voltages.
The power supply pin is bypassed with a capacitor network located close to the ADC084S101.
Because the reference for the ADC084S101 is the supply voltage, any noise on the supply will degrade device
noise performance. To keep noise off the supply, use a dedicated linear regulator for this device, or provide
sufficient decoupling from other circuitry to keep noise off the ADC084S101 supply pin. Because of the
ADC084S101's low power requirements, it is also possible to use a precision reference as a power supply to
maximize performance. Because of the ADC084S101's low power requirements, it is also possible to use a
precision reference as a power supply to maximize performance. The four-wire interface is also shown
connected to a microprocessor or DSP.
LP2950
1 PF
VA
IN1
IN2
IN3
1 PF
0.1 PF
SCLK
ADC084S101
IN4
0.1 PF
5V
CS
DIN
MICROPROCESSOR
DSP
DOUT
GND
Figure 51. Typical Application Circuit
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
19
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
ANALOG INPUTS
An equivalent circuit for one of the ADC084S101's input channels is shown in Figure 52. Diodes D1 and D2
provide ESD protection for the analog inputs. At no time should any input go beyond (VA + 300 mV) or (GND −
300 mV), as these ESD diodes will begin conducting, which could result in erratic operation. For this reason,
these ESD diodes should NOT be used to clamp the input signal.
The capacitor C1 in Figure 52 has a typical value of 3 pF, and is mainly the package pin capacitance. Resistor
R1 is the on resistance of the multiplexer and track / hold switch, and is typically 500 ohms. Capacitor C2 is the
ADC084S101 sampling capacitor, and is typically 30 pF. The ADC084S101 will deliver best performance when
driven by a low-impedance source to eliminate distortion caused by the charging of the sampling capacitance.
This is especially important when using the ADC084S101 to sample AC signals. Also important when sampling
dynamic signals is a band-pass or low-pass filter to reduce harmonics and noise, improving dynamic
performance.
VA
D1
R1
C2
30 pF
VIN
C1
3 pF
D2
Conversion Phase - Switch Open
Track Phase - Switch Closed
Figure 52. Equivalent Input Circuit
20
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
ADC084S101
www.ti.com
SNAS285D – APRIL 2005 – REVISED MARCH 2013
DIGITAL INPUTS AND OUTPUTS
The ADC084S101's digital output DOUT is limited by, and cannot exceed, the supply voltage, VA. The digital
input pins are not prone to latch-up and, and although not recommended, SCLK, CS and DIN may be asserted
before VA without any latchup risk.
POWER SUPPLY CONSIDERATIONS
The ADC084S101 is fully powered-up whenever CS is low, and fully powered-down whenever CS is high, with
one exception: the ADC084S101 automatically enters power-down mode between the 16th falling edge of a
conversion and the 1st falling edge of the subsequent conversion (see Timing Diagrams).
The ADC084S101 can perform multiple conversions back to back; each conversion requires 16 SCLK cycles.
The ADC084S101 will perform conversions continuously as long as CS is held low.
The user may trade off throughput for power consumption by simply performing fewer conversions per unit time.
The Power Consumption vs. Sample Rate curve in the Typical Performance Characteristics section shows the
typical power consumption of the ADC084S101 versus throughput. To calculate the power consumption, simply
multiply the fraction of time spent in the normal mode by the normal mode power consumption , and add the
fraction of time spent in shutdown mode multiplied by the shutdown mode power dissipation.
Power Management
When the ADC084S101 is operated continuously in normal mode, the maximum throughput is fSCLK/16.
Throughput may be traded for power consumption by running fSCLK at its maximum 16 MHz and performing fewer
conversions per unit time, putting the ADC084S101 into shutdown mode between conversions. A plot of typical
power consumption versus throughput is shown in the Typical Performance Characteristics section. To calculate
the power consumption for a given throughput, multiply the fraction of time spent in the normal mode by the
normal mode power consumption and add the fraction of time spent in shutdown mode multiplied by the
shutdown mode power consumption. Generally, the user will put the part into normal mode and then put the part
back into shutdown mode. Note that the curve of power consumption vs. throughput is nearly linear. This is
because the power consumption in the shutdown mode is so small that it can be ignored for all practical
purposes.
Power Supply Noise Considerations
The charging of any output load capacitance requires current from the power supply, VA. The current pulses
required from the supply to charge the output capacitance will cause voltage variations on the supply. If these
variations are large enough, they could degrade SNR and SINAD performance of the ADC. Furthermore,
discharging the output capacitance when the digital output goes from a logic high to a logic low will dump current
into the die substrate, which is resistive. Load discharge currents will cause "ground bounce" noise in the
substrate that will degrade noise performance if that current is large enough. The larger is the output
capacitance, the more current flows through the die substrate and the greater is the noise coupled into the
analog channel, degrading noise performance.
To keep noise out of the power supply, keep the output load capacitance as small as practical. If the load
capacitance is greater than 50 pF, use a 100 Ω series resistor at the ADC output, located as close to the ADC
output pin as practical. This will limit the charge and discharge current of the output capacitance and improve
noise performance.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
21
ADC084S101
SNAS285D – APRIL 2005 – REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (March 2013) to Revision D
•
22
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 21
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC084S101
PACKAGE OPTION ADDENDUM
www.ti.com
23-Aug-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
ADC084S101CIMM/NOPB
ACTIVE
Package Type Package Pins Package
Drawing
Qty
VSSOP
DGS
10
1000
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
Op Temp (°C)
Device Marking
(4/5)
-40 to 85
X25C
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Aug-2017
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
ADC084S101CIMM/NOPB VSSOP
DGS
10
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
1000
178.0
12.4
Pack Materials-Page 1
5.3
B0
(mm)
K0
(mm)
P1
(mm)
3.4
1.4
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Aug-2017
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADC084S101CIMM/NOPB
VSSOP
DGS
10
1000
210.0
185.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
DGS0010A
VSSOP - 1.1 mm max height
SCALE 3.200
SMALL OUTLINE PACKAGE
C
5.05
TYP
4.75
SEATING PLANE
PIN 1 ID
AREA
A
0.1 C
10
1
3.1
2.9
NOTE 3
8X 0.5
2X
2
5
6
B
10X
3.1
2.9
NOTE 4
SEE DETAIL A
0.27
0.17
0.1
C A
1.1 MAX
B
0.23
TYP
0.13
0.25
GAGE PLANE
0 -8
0.15
0.05
0.7
0.4
DETAIL A
TYPICAL
4221984/A 05/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-187, variation BA.
www.ti.com
EXAMPLE BOARD LAYOUT
DGS0010A
VSSOP - 1.1 mm max height
SMALL OUTLINE PACKAGE
10X (0.3)
10X (1.45)
(R0.05)
TYP
SYMM
1
10
SYMM
8X (0.5)
6
5
(4.4)
LAND PATTERN EXAMPLE
SCALE:10X
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4221984/A 05/2015
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DGS0010A
VSSOP - 1.1 mm max height
SMALL OUTLINE PACKAGE
10X (1.45)
10X (0.3)
SYMM
1
(R0.05) TYP
10
SYMM
8X (0.5)
6
5
(4.4)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:10X
4221984/A 05/2015
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising