Texas Instruments | DAC121S101EVM | User Guides | Texas Instruments DAC121S101EVM User guides

Texas Instruments DAC121S101EVM User guides
DAC121S101EVM Booster Pack User’s Guide
User's Guide
Literature Number: SNAU169
August 2014
Contents
1
DAC121S101 BoosterPack Components ................................................................................. 4
2
Software Installation ............................................................................................................. 5
2.1
2.2
2.3
3
Graphical User Interface (GUI)............................................................................................. 5
LaunchPad Firmware Upgrade ............................................................................................ 6
Update USB Driver .......................................................................................................... 7
DAC121S101 BoosterPack Setup and Operation ...................................................................... 8
3.1
3.2
Connections .................................................................................................................. 8
Launching the Software ..................................................................................................... 9
4
Board Layout ..................................................................................................................... 10
5
Schematic
6
......................................................................................................................... 15
Bill of Materials .................................................................................................................. 16
2
Contents
SNAU169 – August 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com
List of Figures
1-1.
DAC121S101EVM Evaluation Board...................................................................................... 4
2-1.
DAC12xSxxx Installation Directory ........................................................................................ 5
2-2.
USB Firmware Upgrade Window .......................................................................................... 6
2-3.
Driver Not Installed .......................................................................................................... 7
3-1.
DAC121S101EVM Attached to MSP430 ................................................................................. 8
3-2.
Part Select .................................................................................................................... 9
4-1.
Top Assembly Layer ....................................................................................................... 10
4-2.
Top Layer Routing
11
4-3.
Power Layer Routing
12
4-4.
4-5.
5-1.
.........................................................................................................
......................................................................................................
Ground Layer Routing .....................................................................................................
Bottom Layer Routing......................................................................................................
DAC121S101EVM Schematic ............................................................................................
13
14
15
List of Tables
1-1.
Device and Package Configurations ...................................................................................... 4
6-1.
DAC121S101 Bill of Materials ............................................................................................ 16
SNAU169 – August 2014
Submit Documentation Feedback
List of Figures
Copyright © 2014, Texas Instruments Incorporated
3
Chapter 1
SNAU169 – August 2014
DAC121S101 BoosterPack Components
Figure 1-1. DAC121S101EVM Evaluation Board
Table 1-1. Device and Package Configurations
4
DEVICE
IC
PACKAGE
U1
LM4120IM5-4.1
SOT-23
U2
DAC128S085CIMK
SOT-6
DAC121S101 BoosterPack Components
Copyright © 2014, Texas Instruments Incorporated
SNAU169 – August 2014
Submit Documentation Feedback
Chapter 2
SNAU169 – August 2014
Software Installation
2.1
Graphical User Interface (GUI)
To use the DAC121S101EVM install the DAC12xSxxx Software:
1. The DAC12xSxxx software is located http://www.ti.com/product/dac121s101, scroll down to the
“software” section, and download the latest evaluation software.
2. Unzip the downloaded file into a known directory, and run the “setup.exe” file located in [Unzip
location]\ DAC12xSxxx \EVM_GUI\ DAC12xSxxx _Installer_v1.zip\ DAC12xSxxx
_Installer\Installer\Volume. Follow the pop-screen instructions by clicking the “Next” button to install the
software.
Figure 2-1. DAC12xSxxx Installation Directory
3. When the installation is finished, please click “Finish” button.
SNAU169 – August 2014
Submit Documentation Feedback
Software Installation
Copyright © 2014, Texas Instruments Incorporated
5
LaunchPad Firmware Upgrade
2.2
www.ti.com
LaunchPad Firmware Upgrade
The MSP430F5529 LaunchPad board can purchased at http://www.ti.com/tool/msp-exp430f5529lp.
MSP430 Firmware Upgrade Application Installation
1. Navigate tohttp://www.ti.com/tool/msp430usbdevpack and click on Get Software.
2. Scroll-down to the end of the page to find the USB Collateral Installers section.
3. Click on MSP430_USB_Firmware_Upgrade_Example-x-x-x-Setup.exe to download the tool; the page
will redirect to a submission form.
4. Complete the information requested and submit the form; if approved, a download button will appear.
5. Run the installation file and follow the on-screen instructions until completion. When asked about the
setup type, select Application Only. Click Finish when done.
SPACE
Firmware upgrade
1. Open the MSP430 USB Firmware Upgrade application. By default, the application can be launched
from Start >> Programs >> Texas Instruments >> MSP430 USB Firmware Upgrade Example.
2. Click Next to proceed on the first prompt; read and accept the license agreement and click Next to
continue.
Figure 2-2. USB Firmware Upgrade Window
3. Enable the Select Firmware button and browse to the downloaded firmware “dac12xsxxx_fw-v0.87.txt”.
4. Press the BSL button on the MSP430 LaunchPad and connect to the PC with a USB cable; if detected,
the text on the Firmware Upgrade tool will change from “No device connected” to “Found 1 device”.
5. Click on the Upgrade Firmware button to program the LaunchPad. Close the application when done.
6
Software Installation
SNAU169 – August 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Update USB Driver
www.ti.com
2.3
Update USB Driver
1. Before launching the DAC12xSxxx software, connect the DAC121S101EVM board to a USB port of
your PC. Go to Device Manager and find “MSP43-USB Example”. Right click and select Update Driver
Software.
Figure 2-3. Driver Not Installed
2. On the next screen, select the “Browse my computer for driver software” option and go to the directory
of your install files and select the “TI_ADC_DAC_EVMs_Driver.inf” file.
3. If prompted with a warning window select “Install this Driver Anyway”. Close the installation window
when it is done. The device manager should now display a “TI_ADC_DAC_EVMs” item followed by a
COM port number.
SNAU169 – August 2014
Submit Documentation Feedback
Software Installation
Copyright © 2014, Texas Instruments Incorporated
7
Chapter 3
SNAU169 – August 2014
DAC121S101 BoosterPack Setup and Operation
3.1
Connections
1. Attach the DAC121S101EVM BoosterPack onto the MSP430F5529 LaunchPad using connectors JA,
JB, JC, JD. The proper orientation of the LaunchPad and DAC121S101EVM is when the text
“LaunchPad” and “2013 TI” are in the same direction.
Figure 3-1. DAC121S101EVM Attached to MSP430
2. Connect the USB cable from the LaunchPad to the PC.
8
DAC121S101 BoosterPack Setup and Operation
Copyright © 2014, Texas Instruments Incorporated
SNAU169 – August 2014
Submit Documentation Feedback
Launching the Software
www.ti.com
3.2
Launching the Software
1. The DAC12xSxxx GUI software can be run by clicking on Start >> All Program >> DAC12xSxxx. After
running the GUI select DAC121S101.
Figure 3-2. Part Select
2. GUI Descriptions
• DB[15:12]: These 4 bits control different operational and power down modes. Bits 14 and 15 are
don’t care bits. See the DAC121S101 datasheet for more details.
• DB[11:0]: These 12 bits are for setting the DAC output codes.
• DB[11:0] Output Type: This field changes DB[11:0] to either binary, decimal, or hexadecimal type.
3. Quick start:
(a) Input “0000” to DB[15:12] to go into normal operation mode
(b) Input “800” to DB[11:0] to output 2.048V (Vref/2)
(c) Click “Write” to send the command to the DAC121S101 part
SNAU169 – August 2014
Submit Documentation Feedback
DAC121S101 BoosterPack Setup and Operation
Copyright © 2014, Texas Instruments Incorporated
9
Chapter 4
SNAU169 – August 2014
Board Layout
Figure 4-1. Top Assembly Layer
10
Board Layout
SNAU169 – August 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com
Figure 4-2. Top Layer Routing
SNAU169 – August 2014
Submit Documentation Feedback
Board Layout
Copyright © 2014, Texas Instruments Incorporated
11
www.ti.com
Figure 4-3. Power Layer Routing
12
Board Layout
SNAU169 – August 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com
Figure 4-4. Ground Layer Routing
SNAU169 – August 2014
Submit Documentation Feedback
Board Layout
Copyright © 2014, Texas Instruments Incorporated
13
www.ti.com
Figure 4-5. Bottom Layer Routing
14
Board Layout
SNAU169 – August 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
JA-7
JA-2
3.3V
1
2
3
4
5
6
7
8
9
10
JA
JC
1
2
3
4
5
6
7
8
9
10
5V
4
6
5
JA-2
JA-7
SCLK
SYNC
DIN
VA
GND
VOUT
3
2
1
U2
DAC121S101CIMK/NOPB
JB-6
R1
VA
C5
0.1µF
200
C4
0.01µF
5V
1
2
EN
IN
GND
REF
OUT
TSW-102-07-G-S
J1
C2
0.1µF
3
4
1
5
U1
LM4120IM5-4.1/NOPB
2
C1
0.047µF
VA
DNP
GND
C7
10µF
1
2
3
VA-EXT
DNP
JVA
SH-JVA_2-3
1
2
3
4
5
6
7
8
9
10
JD
JB
1
2
3
4
5
6
7
8
9
10
JB-6
Chapter 5
SNAU169 – August 2014
Schematic
Figure 5-1. DAC121S101EVM Schematic
SNAU169 – August 2014
Submit Documentation Feedback
Schematic
Copyright © 2014, Texas Instruments Incorporated
15
Chapter 6
SNAU169 – August 2014
Bill of Materials
Table 6-1. DAC121S101 Bill of Materials
16
Designator
Quantity
!PCB
1
Value
Description
Part Number
Manufacturer
Printed Circuit Board
SV601042
Any
CAP, CERM, 0.047uF, 6.3V,
+/-10%, X7R, 0603
GRM188R70J473KA01
D
MuRata
C1
1
0.047µ
ƒ
C2, C5
2
0.1µF
CAP, CERM, 0.1uF, 10V, +/10%, X7R, 0603
C0603C104K8RACTU
Kemet
C4
1
0.01µF
CAP, CERM, 0.01uF, 25V,
+/-10%, X7R, 0603
GRM188R71E103KA01
D
MuRata
C7
1
10µF
CAP, TA, 10uF, 10V, +/-10%,
0.9 ohm, SMD
TPSA106K010R0900
AVX
J1
1
Header, TH, 100mil, 2x1,
Gold plated, 230 mil above
insulator
TSW-102-07-G-S
Samtec
JA, JB, JC, JD
4
Connector, Receptacle,
100mil, 10x1, Gold plated, TH
SSW-110-23-F-S
Samtec
JVA
1
Header, 100mil, 3x1, Tin
plated, TH
PEC03SAAN
Sullins Connector
Solutions
LBL1
1
Thermal Transfer Printable
Labels, 0.650" W x 0.200" H 10,000 per roll
THT-14-423-10
Brady
R1
1
200
RES, 200 ohm, 1%, 0.1W,
0603
CRCW0603200RFKEA
Vishay-Dale
SH-JVA_2-3
1
1×2
Shunt, 100mil, Gold plated,
Black
382811-6
AMP
U1
1
Precision Micropower Low
Dropout Voltage Reference,
5-pin SOT-23, Pb-Free
LM4120IM5-4.1/NOPB
Texas Instruments
U2
1
12-Bit Micro Power, RRO
Digital-to-Analog Converter,
6-pin Tiny SOT23, Pb-Free
DAC121S101CIMK/NO
PB
Texas Instruments
FID1, FID2, FID3
0
Fiducial mark. There is
nothing to buy or mount.
N/A
N/A
GND
0
Black
Test Point, TH, Multipurpose,
Black
5011
Keystone
Electronics
VA-EXT
0
Red
Test Point, TH, Multipurpose,
Red
5010
Keystone
Electronics
Bill of Materials
SNAU169 – August 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
ADDITIONAL TERMS AND CONDITIONS, WARNINGS, RESTRICTIONS, AND DISCLAIMERS FOR
EVALUATION MODULES
Texas Instruments Incorporated (TI) markets, sells, and loans all evaluation boards, kits, and/or modules (EVMs) pursuant to, and user
expressly acknowledges, represents, and agrees, and takes sole responsibility and risk with respect to, the following:
1.
User agrees and acknowledges that EVMs are intended to be handled and used for feasibility evaluation only in laboratory and/or
development environments. Notwithstanding the foregoing, in certain instances, TI makes certain EVMs available to users that do not
handle and use EVMs solely for feasibility evaluation only in laboratory and/or development environments, but may use EVMs in a
hobbyist environment. All EVMs made available to hobbyist users are FCC certified, as applicable. Hobbyist users acknowledge, agree,
and shall comply with all applicable terms, conditions, warnings, and restrictions in this document and are subject to the disclaimer and
indemnity provisions included in this document.
2. Unless otherwise indicated, EVMs are not finished products and not intended for consumer use. EVMs are intended solely for use by
technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical
mechanical components, systems, and subsystems.
3. User agrees that EVMs shall not be used as, or incorporated into, all or any part of a finished product.
4. User agrees and acknowledges that certain EVMs may not be designed or manufactured by TI.
5. User must read the user's guide and all other documentation accompanying EVMs, including without limitation any warning or
restriction notices, prior to handling and/or using EVMs. Such notices contain important safety information related to, for example,
temperatures and voltages. For additional information on TI's environmental and/or safety programs, please visit www.ti.com/esh or
contact TI.
6. User assumes all responsibility, obligation, and any corresponding liability for proper and safe handling and use of EVMs.
7. Should any EVM not meet the specifications indicated in the user’s guide or other documentation accompanying such EVM, the EVM
may be returned to TI within 30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE
EXCLUSIVE WARRANTY MADE BY TI TO USER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR
STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. TI SHALL
NOT BE LIABLE TO USER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RELATED TO THE
HANDLING OR USE OF ANY EVM.
8. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which EVMs might be or are used. TI currently deals with a variety of customers, and therefore TI’s arrangement with
the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services with respect to the handling or use of EVMs.
9. User assumes sole responsibility to determine whether EVMs may be subject to any applicable federal, state, or local laws and
regulatory requirements (including but not limited to U.S. Food and Drug Administration regulations, if applicable) related to its handling
and use of EVMs and, if applicable, compliance in all respects with such laws and regulations.
10. User has sole responsibility to ensure the safety of any activities to be conducted by it and its employees, affiliates, contractors or
designees, with respect to handling and using EVMs. Further, user is responsible to ensure that any interfaces (electronic and/or
mechanical) between EVMs and any human body are designed with suitable isolation and means to safely limit accessible leakage
currents to minimize the risk of electrical shock hazard.
11. User shall employ reasonable safeguards to ensure that user’s use of EVMs will not result in any property damage, injury or death,
even if EVMs should fail to perform as described or expected.
12. User shall be solely responsible for proper disposal and recycling of EVMs consistent with all applicable federal, state, and local
requirements.
Certain Instructions. User shall operate EVMs within TI’s recommended specifications and environmental considerations per the user’s
guide, accompanying documentation, and any other applicable requirements. Exceeding the specified ratings (including but not limited to
input and output voltage, current, power, and environmental ranges) for EVMs may cause property damage, personal injury or death. If
there are questions concerning these ratings, user should contact a TI field representative prior to connecting interface electronics including
input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or inaccurate
operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the applicable EVM user's guide prior
to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During
normal operation, some circuit components may have case temperatures greater than 60°C as long as the input and output are maintained
at a normal ambient operating temperature. These components include but are not limited to linear regulators, switching transistors, pass
transistors, and current sense resistors which can be identified using EVMs’ schematics located in the applicable EVM user's guide. When
placing measurement probes near EVMs during normal operation, please be aware that EVMs may become very warm. As with all
electronic evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in
development environments should use EVMs.
Agreement to Defend, Indemnify and Hold Harmless. User agrees to defend, indemnify, and hold TI, its directors, officers, employees,
agents, representatives, affiliates, licensors and their representatives harmless from and against any and all claims, damages, losses,
expenses, costs and liabilities (collectively, "Claims") arising out of, or in connection with, any handling and/or use of EVMs. User’s
indemnity shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if EVMs fail to perform as
described or expected.
Safety-Critical or Life-Critical Applications. If user intends to use EVMs in evaluations of safety critical applications (such as life support),
and a failure of a TI product considered for purchase by user for use in user’s product would reasonably be expected to cause severe
personal injury or death such as devices which are classified as FDA Class III or similar classification, then user must specifically notify TI
of such intent and enter into a separate Assurance and Indemnity Agreement.
RADIO FREQUENCY REGULATORY COMPLIANCE INFORMATION FOR EVALUATION MODULES
Texas Instruments Incorporated (TI) evaluation boards, kits, and/or modules (EVMs) and/or accompanying hardware that is marketed, sold,
or loaned to users may or may not be subject to radio frequency regulations in specific countries.
General Statement for EVMs Not Including a Radio
For EVMs not including a radio and not subject to the U.S. Federal Communications Commission (FCC) or Industry Canada (IC)
regulations, TI intends EVMs to be used only for engineering development, demonstration, or evaluation purposes. EVMs are not finished
products typically fit for general consumer use. EVMs may nonetheless generate, use, or radiate radio frequency energy, but have not been
tested for compliance with the limits of computing devices pursuant to part 15 of FCC or the ICES-003 rules. Operation of such EVMs may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: For EVMs including a radio, the radio included in such EVMs is intended for development and/or
professional use only in legally allocated frequency and power limits. Any use of radio frequencies and/or power availability in such EVMs
and their development application(s) must comply with local laws governing radio spectrum allocation and power limits for such EVMs. It is
the user’s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power limitations.
Any exceptions to this are strictly prohibited and unauthorized by TI unless user has obtained appropriate experimental and/or development
licenses from local regulatory authorities, which is the sole responsibility of the user, including its acceptable authorization.
U.S. Federal Communications Commission Compliance
For EVMs Annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications could void the user's authority to operate the equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at its own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Compliance (English)
For EVMs Annotated as IC – INDUSTRY CANADA Compliant:
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs Including Radio Transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs Including Detachable Antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Canada Industry Canada Compliance (French)
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
spacer
Important Notice for Users of EVMs Considered “Radio Frequency Products” in Japan
EVMs entering Japan are NOT certified by TI as conforming to Technical Regulations of Radio Law of Japan.
If user uses EVMs in Japan, user is required by Radio Law of Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use EVMs only after user obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs, or
Use of EVMs only after user obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect
to EVMs. Also, do not transfer EVMs, unless user gives the same notice above to the transferee. Please note that if user does not
follow the instructions above, user will be subject to penalties of Radio Law of Japan.
http://www.tij.co.jp
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 本開発キットは技術基準適合証明を受けておりません。 本製品の
ご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
http://www.tij.co.jp
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising