Texas Instruments | TSC2008EVM and TSC2008EVM-PDK | User Guides | Texas Instruments TSC2008EVM and TSC2008EVM-PDK User guides

Texas Instruments TSC2008EVM and TSC2008EVM-PDK User guides
User's Guide
SLAU248 – May 2008
TSC2008EVM and TSC2008EVM-PDK User's Guide
This user's guide describes the characteristics, operation, and use of the TSC2008EVM, both by itself and
as part of the TSC2008EVM-PDK. This evaluation module (EVM) is a 4-wire touch screen controller EVM
which also has auxiliary input and temperature measuring capabilities. A complete circuit description,
schematic diagram, and bill of materials are included.
The following related documents are available through the Texas Instruments Web site at www.ti.com.
Table 1. EVM-Compatible Device Data Sheets
1
2
3
4
5
6
7
8
9
Device
Literature Number
TSC2008
SBAS406
TAS1020B
SLES025
REG1117-5
SBVS001
TPS767D318
SLVS209
SN74LVC125A
SCAS290
SN74LVC1G125
SCES223
SN74LVC1G07
SCES296
Contents
EVM Overview ............................................................................................................... 2
Analog Interface ............................................................................................................. 2
Digital Interface .............................................................................................................. 2
Power Supplies .............................................................................................................. 3
EVM Operation .............................................................................................................. 4
Kit Operation ................................................................................................................. 5
EVM Bill of Materials ...................................................................................................... 10
TSC2008EVM Schematic ................................................................................................ 12
USB-MODEVM Schematic ............................................................................................... 12
List of Figures
......................................................................................
..................................................................................................
1
TSC2008EVM-PDK Block Diagram
6
2
Default Software Screen
7
1
EVM-Compatible Device Data Sheets ................................................................................... 1
2
Analog Interface Pinout .................................................................................................... 2
3
Digital Interface Pinout ..................................................................................................... 3
4
Power Supply Pinout ....................................................................................................... 3
5
Power Selection Options - JMP1
6
List of Jumpers .............................................................................................................. 5
2
TSC2008EVM Bill of Materials
2
USB-MODEVM Bill of Materials
List of Tables
.........................................................................................
..........................................................................................
........................................................................................
4
10
11
NI Speedy-33 is a trademark of Hyperception, Inc.
Windows is a trademark of Microsoft Corporation.
SPI is a trademark of Motorola, Inc.
I2C is a trademark of Philips Corporation.
SLAU248 – May 2008
Submit Documentation Feedback
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
1
EVM Overview
www.ti.com
1
EVM Overview
1.1
Features
•
•
Full-featured evaluation board for the TSC2008 4-wire resistive touch screen controller (TSC).
Modular design for use with a variety of DSP and microcontroller interface boards.
The TSC2008EVM-PDK is a complete evaluation kit, which includes a USB-based motherboard and
evaluation software for use with a personal computer running Microsoft Windows™ operating systems.
1.2
Introduction
The TSC2008EVM is in the Texas Instruments modular EVM form factor, which allows direct evaluation of
the performance and operating characteristics of the TSC2008 and eases software development and
system prototyping. This EVM is compatible with the 5-6K Interface Board (SLAU104) from Texas
Instruments and additional third-party boards such as the NI Speedy-33™ from National Instruments
Corporation. (www.ni.com)
The TSC2008EVM-PDK is a complete evaluation/demonstration kit, which includes a USB-based
motherboard called the USB-MODEVM interface board and evaluation software for use with a personal
computer running Microsoft Windows operating systems.
2
Analog Interface
For maximum flexibility, the TSC2008EVM is designed for easy interfacing to multiple analog sources.
Samtec part numbers SSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a convenient 10-pin,
dual-row header/socket combination at J1. This header/socket provides access to the analog input pins of
the TSC. Consult Samtec at www.samtec.com, or call 1-800-SAMTEC-9 for a variety of mating connector
options.
Table 2. Analog Interface Pinout
3
Pin Number
Signal
Description
J1.2
X-
Touch screen X+ electrode
J1.4
X-
Touch screen X- electrode
J1.6
Y+
Touch screen Y+ electrode
J1.8
Y-
Touch screen Y- electrode
J1.10
Unused
J1.12
AUX
J1.14
Unused
J1.16
Unused
J1.18
Unused
J1.20
Unused
J1.15
Unused
J1.1-J1.J19 (odd)
AGND
Auxiliary input, 0 V to VREF
Analog ground connections (except J1.15)
Digital Interface
The TSC2008EVM is designed to easily interface with multiple control platforms. Samtec part numbers
SSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a convenient 10-pin, dual-row header/socket
combination at J2. This header/socket provides access to the digital control and serial data pins of the
TSC. Consult Samtec at www.samtec.com or call 1-800-SAMTEC-9 for a variety of mating connector
options.
2
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
SLAU248 – May 2008
Submit Documentation Feedback
Power Supplies
www.ti.com
Table 3. Digital Interface Pinout
4
Pin Number
Signal
J2.1
Unused
Description
J2.2
Unused
J2.3
SCLK
SPI serial clock
J2.4
DGND
Digital ground
J2.5
Unused
J2.6
Unused
J2.7
CS
J2.8
Unused
J2.9
Unused
J2.10
DGND
Digital ground
J2.11
SDI
SPI MOSI - serial data input to TSC from host
J2.12
Unused
J2.13
SDO
J2.14
Unused
J2.15
PENIRQ
PENIRQ Pen interrupt output from TSC, active low
J2.16
SCL
I2C™ bus serial clock
J2.17
Unused
J2.18
DGND
J2.19
Unused
J2.20
SDA
SPI chip selection, active low
SPI MISO - serial data output from TSC to host
Digital ground
I2C bus serial data line
Power Supplies
J3 provides connection to the common power bus for the TSC2008EVM. Power is supplied on the pins
listed in Table 4.
Table 4. Power Supply Pinout
Signal
Pin Number
Signal
Unused
1
2
Unused
Unused
3
4
Unused
DGND
5
6
AGND
+1.8VD
7
8
Unused
+3.3VD
9
10
Unused
When power is supplied to J3, JMP1 allows for one of two different DC voltages to be selected as power
for the TSC. See the schematic and PCB silkscreen for details.
The TSC2008EVM-PDK motherboard (the USB-MODEVM interface board) supplies power to J3 of the
TSC2008EVM. Power for the motherboard is supplied either through its USB connection or via terminal
blocks on the board.
4.1
TSC Power
Power for the TSC2008 VDD can be supplied either from the +1.8VD terminal or from the +3.3VD terminal.
JMP1 selects which of these voltages is routed to the TSC2008. When JMP1 is in the default factory
condition (shunt on pins 2-3), power to the TSC comes from J3.9 (+3.3VD). When the shunt is installed on
JMP1 pins 1-2, power comes from J3.7 (+1.8VD). Removing the shunt on JMP1, the user can connect
any DC power supply between 1.2VD and 3.6VD to VCC by connecting the power to JMP1 pin 2.
SLAU248 – May 2008
Submit Documentation Feedback
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
3
EVM Operation
www.ti.com
Table 5. Power Selection Options - JMP1
4.2
SHUNT ON PINS
VDD
VOLTAGE FROM J3 PIN
1-2
+1.8VD
7
2-3
+3.3VD
9
Removed
+1.2VD and +3.6VD
External
Stand-Alone Operation
When used as a stand-alone EVM, power can be applied to TP6 (VDD), referenced to TP12 (GND).
CAUTION
Verify that all power supplies are within the safe operating limits shown on the
TSC2008 data sheet (SBAS406) before applying power to the EVM.
4.3
USB-MODEVM Interface Power
The USB-MODEVM interface board can be powered from several different sources:
• USB
• 6VDC-10 VDC AC/DC external wall supply (not included)
• Laboratory power supply
When powered from the USB connection, JMP6 should have a shunt from pins 1-2 (this is the default
factory configuration). When powered from 6VDC-10 VDC, either through the J8 terminal block or J9
barrel jack, JMP6 should have a shunt installed on pins 2-3. If power is applied in any of these ways,
onboard regulators generate the required supply voltages, and no further power supplies are necessary.
If laboratory supplies are used to provide the individual voltages required by the USB-MODEVM interface
board, JMP6 should have no shunt installed. Voltages then are applied to J2 (+5VA), J3 (+5VD), J4
(+1.8VD), and J5 (+3.3VD). The +1.8VD and +3.3VD also can be generated on the board by the onboard
regulators from the +5VD supply; to enable this supply, the switches on SW1 need to be set to enable the
regulators by placing them in the ON position (lower position, looking at the board with text reading
right-side up). If +1.8VD and +3.3VD are supplied externally, disable the onboard regulators by placing
SW1 switches in the OFF position.
Each power supply voltage has an LED (D1-D7) which lights when the power supplies are active.
5
EVM Operation
The following section provides information on the analog input, digital control, and general operating
conditions of the TSC2008EVM.
5.1
Analog Input
The analog input sources (touch screen and auxiliary input) can be applied directly to J1 (top or bottom
side) or through signal-conditioning modules available for the modular EVM system.
5.2
Digital Control
The digital control signals can be applied directly to J2 (top or bottom side). The modular TSC2008EVM
also can be connected directly to a DSP or microcontroller interface board, such as the USB-MODEVM
interface board if purchased as part of the TSC2008EVM-PDK. See the product folder for the TSC2008 for
a current list of compatible interface and/or accessory boards.
5.3
Default Jumper Locations
Table 6 provides a list of jumpers found on the EVM and their factory default conditions.
4
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
SLAU248 – May 2008
Submit Documentation Feedback
Kit Operation
www.ti.com
Table 6. List of Jumpers
6
Jumper
Shunt Position
Jumper Description
JMP1
2-3
Analog power select (default is +3.3VD)
JMP2
Closed
EEPROM address select. When installed and used with the USB-MODEVM, firmware for the
motherboard is executed from the EEPROM on the TSC2008EVM. This is the default mode.
Kit Operation
The following section provides information on using the TSC2008EVM-PDK, including setup, program
installation, and program usage.
6.1
TSC2008EVM-PDK Block Diagram
A block diagram of the TSC2008EVM-PDK is shown in Figure 1. The evaluation kit consists of two circuit
boards connected together. The motherboard is designated as the USB-MODEVM interface board; the
daughtercard is the TSC2008EVM described previously in this manual.
SLAU248 – May 2008
Submit Documentation Feedback
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
5
Kit Operation
www.ti.com
TSC2008EVM
X+
X−
Y+
Y−
AUX
TSC2008
SCLK
SS
MOS2
MT5C
PENIRQ
EVM Position 1
Control Interface
SPI, I2C
TAS1020B
USB 8052
microcontroller
EVM Position 2
USB
I2S, AC97
Audio Interface
Figure 1. TSC2008EVM-PDK Block Diagram
The USB-MODEVM interface board is intended to be used in USB mode, where control of the installed
EVM is accomplished using the onboard USB controller device. However, provision is made for driving all
the data buses (I2C, SPI™, and I2S/AC97) externally. The source of these signals is controlled by SW2 on
the USB-MODEVM.
6.2
Quick Start
Before installing the TSC2008EVM board on top of the USB-MODEVM board, check SW2-1, SW2-2, and
SW2-3 on the USB-MODEVM board to ensure that at least one of these three is OFF
Ensure that the TSC2008EVM is installed on the USB-MODEVM interface board. The TSC2008EVM
should be installed in the topmost position, using J11, J12, and J13 on the USB-MODEVM.
6
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
SLAU248 – May 2008
Submit Documentation Feedback
Kit Operation
www.ti.com
Place the CD-ROM into your personal computer (PC) CD-ROM drive. Locate the Setup program on the
disk, and run it. The Setup program installs the TSC2008 Evaluation software on your PC.
Accept the license agreement, and continue the installation.
When the installation completes, click Finish on the TSC2008EVM installer window. You may be prompted
to restart your computer.
When installation is complete, attach a USB cable from your PC to the USB-MODEVM interface board. As
configured at the factory, the board is powered from the USB interface; so, the power indicator LEDs on
the USB-MODEVM should light. Once this occurs, launch the TSC2008 evaluation software on your PC. It
is suggested that users read the readme_install.txt file for up-to-date, step-by-step instructions.
The software should automatically find the TSC2008EVM, and a screen similar to the one shown in
Figure 2 should appear.
Figure 2. Default Software Screen
In order to use the touch screen features, a user needs to connect a 4-wire resistive touch screen to J1 of
the TSC2008EVM, as described previously.
SLAU248 – May 2008
Submit Documentation Feedback
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
7
Kit Operation
6.3
www.ti.com
USB-MODEVM Interface Board
The simple diagram shown in Figure 1 shows only the basic features of the USB-MODEVM interface
board. The board is built around a TAS1020B streaming audio USB controller with an 8051-based core.
The board features two positions for modular EVMs, or one double-wide serial modular EVM may be
installed.
For use with the TSC2008, the TSC2008EVM is installed in the topmost EVM slot, which connects the
TSC2008 digital control interface to the SP1 port, realized using the TAS1020B. Because the TSC2008
has no audio features, the lower EVM slot, which is connected to the TAS1020B digital audio interface, is
not used.
As configured from the factory, the board is ready to use with the TSC2008EVM.
6.4
Program Description
After the TSC2008EVM-PDK software installation (described in Section 6.2), evaluation and development
with the TSC2008 can begin.
6.4.1
Touch Screen Functions Panel
The touch screen box in this panel is updated when a touch is detected on the touch screen. As the touch
screen is drawn on, the motion on the touch screen is translated into pixels on this box. The software
takes X, Y, and Z readings which are shown to the right of the touch screen box. As the touch pressure is
increased, the pixel size increases; a lighter touch results in smaller pixel sizes.
The Z-value displayed is not what is described in the TSC2008 data sheet, because in the data sheet
equation, it is assumed that the sheet resistance of the touch screen being used is known. The value used
in this program is calculated by Equation 2 of the TSC2008 data sheet, but without multiplying it by the
RX-plate resistance. This value ranges from 0 to 3, and larger, with larger numbers representing a more
forceful press on the screen. Using the Maximum Z Value to Display knob, you can set a threshold so
that the program does not display lightly pressed points. This threshold setting helps to eliminate display
of spurious points that may result from touch screen mechanical bouncing.
The display can be cleared by pressing the Clear Graph button on the screen.
6.4.2
Data Acquisition Functions Panel
The TSC2008 has provision for measuring one auxiliary input voltages (AUX) and temperature. This panel
displays the measured values for these parameters. Measurements are updated only when the touch
screen is not being pressed.
Temperature is displayed using both methods described in the TSC2008 data sheet. Using the TEMP0
and TEMP1 measurements, a temperature reading with 2°C resolution and accuracy is achieved. Using
only the TEMP0 measurement, a reading with 0.3°C resolution is possible, but this option requires
knowing the TEMP0 value at +25°C; this normally is a calibration that the user performs. This program
assumes that TEMP0 = 600 mV at +25°C.
6.4.3
Configuration Panel
The TSC2008 can be configured to operate in 8-bit or 12-bit resolution modes. Control over the mode
used is selected in this panel.
Touch screen measurements can be made in either single-ended or differential mode; see the TSC2008
data sheet for a discussion of these modes. The touch screen measurement mode can also be selected in
this panel. If single-ended mode is used, an external reference is highly recommended; however,
single-ended measurements are discouraged for touch screen use because differential mode yields far
more accurate results.
The two power-down bits of the TSC2008 can be set from this panel as well. A brief description of the
mode selected is shown on the screen when setting these bits; see Table 3 (Command Byte Definitions)
of the TSC2008 data sheet (SBAS406) for details on what these bits do.
8
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
SLAU248 – May 2008
Submit Documentation Feedback
Kit Operation
www.ti.com
6.4.4
Setup Panel
TSC2008 has several software programmable features that can be set up by TSC2008 in the setup mode,
when A[2:0] = 2h.
Software reset can bring TSC2008 to its power-up default condition. When clicking on the LED and it
becomes green, the TSVC2008 is software reset.
TSC2008 can be totally compatible to TSC2046 on their data protocols, that is: the MSB of MISO signal
from the TSC starts at the falling edge of the ninth SCLK, that is: the SDO data is readable from the rising
edge of the tenth SCLK. Besides, TSC2008 can have its SDO output readable from the rising edge of the
ninth SCLK. This option can be selected by clicking on the TSC2046 Timing button. TSC2008 output
starting from the tenth SCLK when the TSC2046 Timing is enabled; and TSC2008 outputs starting from
the ninth SLK when the TSC2046 Timing is disabled. TSC2008 is defaulted with the TSC2046 Timing
being enabled.
TSC2008 has a built-in MVA filter, which is enabled by default. The MV filter can be disabled/enabled by
clicking on the MVA Filter button.
The PENIRQ can be used as an interrupt to the host and is pulled up by RIRQ internally. The RIRQ is with a
programmable value of either 50 kΩ (default) or 90 kΩ. The Internal PENIRQ Pullup button is used to
select the RIRQ.
For more details on the programmable features, see the data sheet.
6.4.5
Datalogging
The software can record the data it takes from the TSC2008 to a tab-delimited file, suitable for importing
into spreadsheets. To do this, first go into the File menu, and select Log Data to File..., which opens a
file-select window and allows you to specify a file to which to write the data. At the same time, this enables
the Datalogging menu.
When ready to begin recording data to a file, select Datalogging → Start Logging. Data is written to the file
until Datalogging → Stop Logging is selected. When the screen is not touched, the AUX and TEMP values
are written to the file, and the X, Y, Z1, and Z2 parameters are written to the file with values of 9999, to
indicate that they are not updated. When the screen is touched, the X, Y, Z1, and Z2 parameters are
written while the AUX and TEMP values are written to the file as 9999. Because the program constantly
updates at a rate of about 400 readings per second, datalog files can quickly grow large; therefore, log
only that data which is necessary.
The format of the data file has the first column as the time in milliseconds (which is just a timer in the
program; it can arbitrarily start at any number), then X, Y, Z1, Z2, AUX, TEMP0, and TEMP1 columns.
Every new reading is a new row in the file.
SLAU248 – May 2008
Submit Documentation Feedback
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
9
EVM Bill of Materials
7
www.ti.com
EVM Bill of Materials
Table 7 and Table 8 contain a complete bill of materials for the modular TSC2008EVM evaluation board
and the USB-MODEVM interface board, respectively (included only in the TSC2008EVM-PDK).
Table 7. TSC2008EVM Bill of Materials
Qty
Value
Ref Des
Description
Vendor
Part Number
1
100
R1
1/8W 5% Chip Resistor
Panasonic
ERJ-6GEYJ101V
2
2.7K
R2, R3
1/10W 5% Chip Resistor
Panasonic
ERJ-6GEYJ272V
1
20K
R4
1/10W 5% Chip Resistor
Panasonic
ERJ-6GEYJ203V
1
0.1μF
C1
25V Ceramic Chip Capacitor, ±10%,
X7R
TDK
C2012X7R1E104K
2
1μF
C6, C7
16V Ceramic Chip Capacitor, ±10%,
X7R
TDK
C2012X7R1C105K
1
U1
Touch Screen Controller
Texas Instruments
TSC2008IRGV
1
U2
I2C 64K EEPROM, 1.8–5.5V
Microchip
24AA64-I/SN
2
J1A, J2A
20 Pin SMT Plug
Samtec
TSM-110-01-L-DV-P
1
J3A
10 Pin SMT Plug
Samtec
TSM-105-01-L-DV-P
2
J1B, J2B
20 pin SMT Socket
Samtec
SSW-110-22-F-D-VS-K
1
J3B
10 pin SMT Socket
Samtec
SSW-105-22-F-D-VS-K
1
N/A
TSC2008 EVM PWB
Texas Instruments
6495737
1
JMP2
Terminal Strip, 2 pin (2×1)
Samtec
TSW-102-07-G-S
1
JMP1
Terminal Strip, 3 pin (3×1)
Samtec
TSW-103-07-G-S
2
TP6, TP12
Testpoint, Large-Loop
Keystone Electronics
5011
TP1–TP5, TP7–TP11
Testpoint, Mini-Loop
Keystone Electronics
5000
N/A
Shorting Blocks
Samtec
SNT-100-BK-G-H
10
2
Not
Installed
ATTENTION: All components should be RoHS compliant. Some part numbers may be either leaded or RoHS. Verify purchased
components are RoHS compliant.
10
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
SLAU248 – May 2008
Submit Documentation Feedback
EVM Bill of Materials
www.ti.com
Table 8. USB-MODEVM Bill of Materials
Reference Designator
Description
Manufacturer
Manufacturer's Part No.
R4
10Ω 1/10W 5% Chip Resistor
Panasonic
ERJ-3GEYJ100V
R10, R11
27.4Ω 1/16W 1% Chip Resistor
Panasonic
ERJ-3EKF27R4V
R20
75Ω 1/4W 1% Chip Resistor
Panasonic
ERJ-14NF75R0U
R19
220Ω 1/10W 5% Chip Resistor
Panasonic
ERJ-3GEYJ221V
R14, R21, R22
390Ω 1/10W 5% Chip Resistor
Panasonic
ERJ-3GEYJ391V
R13
649Ω 1/16W 1% Chip Resistor
Panasonic
ERJ-3EKF6490V
R9
1.5KΩ 1/10W 5% , Chip Resistor
Panasonic
ERJ-3GEYJ152V
R1–R3, R5–R8
2.7KΩ 1/10W 5% , Chip Resistor
Panasonic
ERJ-3GEYJ272V
R12
3.09KΩ 1/16W 1% , Chip Resistor
Panasonic
ERJ-3EKF3091V
R15, R16
10KΩ 1/10W 5%, Chip Resistor
Panasonic
ERJ-3GEYJ103V
R17, R18
100KΩ 1/10W 5%, Chip Resistor
Panasonic
ERJ-3GEYJ104V
RA1
10KΩ 1/8W Octal Isolated, Resistor Array
CTS Corporation
742C163103JTR
C18, C19
33pF 50V Ceramic, Chip Capacitor, ±5%, NPO
TDK
C1608C0G1H330J
C13, C14
47pF 50V Ceramic, Chip Capacitor, ±5%, NPO
TDK
C1608C0G1H470J
C20
100pF 50V Ceramic Chip Capacitor, ±5%, NPO
TDK
C1608C0G1H101J
C21
1000pF 50V Ceramic Chip Capacitor, ±5%, NPO
TDK
C1608C0G1H102J
C15
0.1μF 16V Ceramic Chip Capacitor, ±10%,X7R
TDK
C1608X7R1C104K
C16, C17
0.33μF 16V Ceramic Chip Capacitor, ±20%,Y5V
TDK
C1608X5R1C334K
C9–C12–C28
1µF 6.3V Ceramic Chip Capacitor, ±10%, X5R
TDK
C1608X5R0J105K
C1–C8
10μF 6.3V Ceramic Chip Capacitor, ±10%, X5R
TDK
C3216X5R0J106K
D1
50V, 1A, Diode MELF SMD
Micro Commercial
Components
DL4001
D2
Yellow Light Emitting Diode
Lumex
SML-LX0603YW-TR
D3, D4, D6, D7
Green Light Emitting Diode
Lumex
SML-LX0603GW-TR
D5
Red Light Emitting Diode
Lumex
SML-LX0603IW-TR
Q1, Q2
N-Channel MOSFET
Zetex
ZXMN6A07F
X1
6MHz Crystal SMD
Epson
MA-505 6.000M-C0
U8
USB Streaming Controller
Texas Instruments
TAS1020BPFB
U2
5V LDO Regulator
Texas Instruments
REG1117-5
U9
3.3V/1.8V Dual Output LDO Regulator
Texas Instruments
TPS767D318PWP
U3, U4
Quad, 3-State Buffers
Texas Instruments
SN74LVC125APW
U5–U7
Single IC Buffer Driver with Open Drain o/p
Texas Instruments
SN74LVC1G07DBVR
U10
Single 3-State Buffer
Texas Instruments
SN74LVC1G125DBVR
U1
64K 2-Wire Serial EEPROM I2C
Microchip
24LC64I/SN
USB-MODEVM PCB
Texas Instruments
6463995
TP1–TP6, TP9–TP11
Miniature test point terminal
Keystone Electronics
5000
TP7, TP8
Multipurpose test point terminal
Keystone Electronics
5011
J7
USB Type B Slave Connector Thru-Hole
Mill-Max
897-30-004-90-000000
J1–J5, J8
2-position terminal block
On Shore Technology
ED555/2DS
J9
2.5mm power connector
CUI Stack
PJ-102B
J10
BNC connector, female, PC mount
AMP/Tyco
414305-1
J11A, J12A, J21A, J22A
20-pin SMT plug
Samtec
TSM-110-01-L-DV-P
J11B, J12B, J21B, J22B
20-pin SMT socket
Samtec
SSW-110-22-F-D-VS-K
J13A, J23A
10-pin SMT plug
Samtec
TSM-105-01-L-DV-P
J13B, J23B
10-pin SMT socket
Samtec
SSW-105-22-F-D-VS-K
J6
4-pin double row header (2x2) 0.1"
Samtec
TSW-102-07-L-D
J14, J15
12-pin double row header (2x6) 0.1"
Samtec
TSW-106-07-L-D
JMP1–JMP4
2-position jumper, 0.1" spacing
Samtec
TSW-102-07-L-S
SLAU248 – May 2008
Submit Documentation Feedback
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
11
TSC2008EVM Schematic
www.ti.com
Table 8. USB-MODEVM Bill of Materials (continued)
Reference Designator
Description
Manufacturer
Manufacturer's Part No.
JMP8–JMP14
2-position jumper, 0.1" spacing
Samtec
TSW-102-07-L-S
JMP5, JMP6
3-position jumper, 0.1" spacing
Samtec
TSW-103-07-L-S
JMP7
3-position dual row jumper, 0.1" spacing
Samtec
TSW-103-07-L-D
SW1
SMT, half-pitch 2-position switch
C&K Division, ITT
TDA02H0SK1
SW2
SMT, half-pitch 8-position switch
C&K Division, ITT
TDA08H0SK1
Jumper plug
Samtec
SNT-100-BK-T
8
TSC2008EVM Schematic
The schematic diagram is provided as a reference.
9
USB-MODEVM Schematic
The schematic diagram is provided as a reference.
12
TSC2008EVM and TSC2008EVM-PDK User's Guide
Copyright © 2008, Texas Instruments Incorporated
SLAU248 – May 2008
Submit Documentation Feedback
1
2
3
4
5
6
REVISION HISTORY
REV
ENGINEERING CHANGE NUMBER
APPROVED
D
D
TP5
TP6
J1
TP9
TP10
J2A (TOP) = SAM_TSM-110-01-L-DV-P
J2B (BOTTOM) = SAM_SSW-110-22-F-D-VS-K
+VDD
J2
1
3
5
7
9
11
13
15
17
19
C6
1uF
AUX
U1
TP3
Y-
C
R1
12
AUX
100 ohm
X+
Y+
XY-
SCLK
CS
SDI
AUX
SDO
PENIRQ
C3
NI
C4
NI
C5
NI
SCLK
SS
MOSI
16
15
MISO
PENIRQ
TP11
+VDD
R2
2.7K
C
U2
+VDD
8
R4
C7
20k
1uF
TP12
TSC2008IRGV
R3
2.7K
DAUGHTER-SERIAL
GND
C2
NI
10
C1
0.1uF
4
3
2
2
4
6
8
10
12
14
16
18
20
GPIO0
DGND
GPIO1
GPIO2
DGND
GPIO3
GPIO4
SCL
DGND
SDA
5
HEADER-10X2
6
7
8
9
X+
Y+
X-
CNTL
CLKX
CLKR
FSX
FSR
DX
DR
INT
TOUT
GPIO5
6
X+
XY+
Y-
TP8
5
2
4
6
8
10
12
14
16
18
20
VDD/REF
1
3
5
7
9
11
13
15
17
19
TP7
4
VCC
SCL
TP4
VSS
WP
TP2
SDA
TP1
A0
A1
A2
J1A (TOP) = SAM_TSM-110-01-L-DV-P
J1B (BOTTOM) = SAM_SSW-110-22-F-D-VS-K
2
JMP2
7
1
2
3
24AA64I/SN
1
J3A (TOP) = SAM_TSM-105-01-L-DV-P
J3B (BOTTOM) = SAM_SSW-105-22-F-D-VS-K
B
B
J3
GND
1
3
5
7
9
+VA
+5VA
DGND
+1.8VD
+3.3VD
-VA
-5VA
AGND
VD1
+5VD
2
4
6
8
10
DAUGHTER-POWER
1
2
3
+VDD
JMP1
ti
A
DATA ACQUISITION PRODUCTS
HIGH-PERFORMANCE ANALOG DIVISION
SEMICONDUCTOR GROUP
12500 TI Blvd., Dallas, TX 75243, USA
TITLE
ENGINEER
Wendy Fang
DRAWN BY
Robert Benjamin
DOCUMENT CONTROL NO. 6495738
SHEET
1
2
3
4
5
1
OF
1
TSC2008 Evaluation Module
SIZE B
DATE
REV A
1-JAN-2008
FILE
6
A
1
2
3
4
6
5
REVISION HISTORY
REV
IOVDD
R5
2.7K
2
5
9
12
1
USB MCK
4
10
USB I2S
13
J6
Q2
ZXMN6A07F
EXTERNAL I2C
SDA
SCL
WP
8
A0
A1
A2
U1
VCC
C9
1uF
4
1
1
3
5
7
9
11
3
2
44
43
42
41
40
39
37
38
36
35
34
32
R12
3.09K
.001uF
R10
27.4
R11
C13
47pF
C14
47pF
R7
2.7K
JMP8
1
2
P1.2
P1.1
P1.0
+3.3VD
C11
1uF
C12
1uF
C
MOSI
SS
SCLK
RESET
14
VCC
J15
1
3
5
7
9
11
3
6
8
11
1Y
2Y
3Y
4Y
7
GND
2
4
6
8
10
12
EXTERNAL SPI
USB RST
USB SPI
P3.5
JMP13
1
2
D2
+3.3VD
YELLOW
C25
R8
2.7K
P3.4
JMP14
1
2
IOVDD
P3.3
B
U6
1uF
4
2
INT
3
J8
5
B
1A
2A
3A
4A
1OE
2OE
3OE
4OE
JMP12
1
2
SML-LX0603YW-TR
MISO
SN74LVC1G07DBV
SN74LVC125APW
MRESET
649
2
U4
2
5
9
12
1
4
10
13
USB ACTIVE
R13
4
1uF
JMP11
1
2
C10
1uF
EXTERNAL AUDIO DATA
C27 IOVDD
JMP10
1
2
C24
1uF
SW DIP-8
P1.3
JMP9
1
2
SN74LVC1G07DBV
ED555/2DS
+5VD
EXT PWR IN
+1.8VD
R14
390
U9
5
6
4
1
2
3
6VDC-10VDC IN
D3
SML-LX0603GW-TR
JMP6
PWR SELECT
GREEN
3
9
U2
REG1117-5
3
C15 DL4001
0.1uF
VIN
C16
0.33uF
VOUT
GND
D1
10
11
12
2
R15
10K
C6
10uF
1
J9
R16
10K
+5VD
A
+3.3VD
+1.8VD
IOVDD
JMP7
1
2
3
4
5
6
TP6
1IN
1IN
1EN
1GND
2GND
2EN
2IN
2IN
1RESET
1OUT
1OUT
2RESET
2OUT
2OUT
TPS767D318PWP
CUI-STACK PJ102-B
2.5 MM
SW1
1
2
4
3
24
23
22
18
17
R17
100K
C7
10uF
D5
SML-LX0603IW-TR
R18
100K
R4
10
+3.3VD
RED
R19
220
ti
C8
10uF
D4
SML-LX0603GW-TR
C17
0.33uF
1.8VD ENABLE
3.3VD ENABLE
28
GREEN
DATA ACQUISITION PRODUCTS
REGULATOR ENABLE
6730 SOUTH TUCSON BLVD., TUCSON, AZ 85706 USA
TITLE
ENGINEER RICK DOWNS
USB-MODEVM INTERFACE
DRAWN BY ROBERT BENJAMIN
DOCUMENT CONTROL NO. 6463996
SHEET 1
2
A
HIGH PERFORMANCE ANALOG DIVISION
SEMICONDUCTOR GROUP
IOVDD SELECT
1
SW2
1
2
3
4
5
6
7
8
PWR_DWN
U7
31
30
29
27
26
25
24
23
8
21
33
2
16
15
14
13
12
11
10
9
2
4
6
8
10
12
1uF
TP11
+3.3VD
IOVDD
C26
3
P1.7
P1.6
P1.5
P1.4
P1.3
P1.2
P1.1
P1.0
DVDD
DVDD
DVDD
AVDD
9
10
11
12
13
14
15
17
18
19
20
22
27.4
XTALO
XTALI
PLLFILI
PLLFILO
MCLKI
PUR
DP
DM
DVSS
DVSS
DVSS
AVSS
MRESET
TEST
EXTEN
RSTO
P3.0
P3.1
P3.2/XINT
P3.3
P3.4
P3.5
NC
NC
7
1
2
3
1.5K
+3.3VD
U8
TAS1020BPFB
SCL
SDA
VREN
RESET
MCLKO2
MCLKO1
CSCLK
CDATO
CDATI
CSYNC
CRESET
CSCHNE
46
47
48
1
3
5
6
7
4
16
28
45
100pF
C21
R9
J14
1uF
33pF
MA-505 6.000M-C0
6.00 MHZ
J7 USB SLAVE CONN
897-30-004-90-000000
I2SDOUT
C23
U5
C19
C20
4
3
2
1
BCLK
SN74LVC1G07DBV
33pF
24LC64I/SN
GND
D+
DVCC
X1
C18
A0
A1
A2
USB I2S
USB MCK
USB SPI
USB RST
EXT MCK
LRCLK
IOVDD
4
VSS
R20
75
MCLK
7
GND
R6
2.7K
RA1
10K
I2SDIN
6
5
+3.3VD
SCL
C
SN74LVC1G125DBV
3
6
8
11
1Y
2Y
3Y
4Y
D
2
SN74LVC125APW
+3.3VD
TP10
14
VCC
+3.3VD
5
1
3
1A
2A
3A
4A
1OE
2OE
3OE
4OE
5
2
4
4
1uF
U3
APPROVED
J10
EXT MCLK
U10
3
R3
2.7K
TP9
SDA
1uF
5
C22
Q1
ZXMN6A07F
D
C28 IOVDD
IOVDD
+3.3VD
ENGINEERING CHANGE NUMBER
3
4
5
OF
2
FILE
SIZE B
DATE 10-Jun-2004
REV A
G:\USB Motherboard - Modular Evm\Schematic\USB Motherboard - ModEvm.ddb - Docume
6
1
2
3
4
6
5
REVISION HISTORY
REV
ENGINEERING CHANGE NUMBER
APPROVED
D
1
2
3
D
J11
J12
A0(+)
A1(+)
A2(+)
A3(+)
A4
A5
A6
A7
REFREF+
2
4
6
8
10
12
14
16
18
20
+5VA
J13A (TOP) = SAM_TSM-105-01-L-DV-P
J13B (BOTTOM) = SAM_SSW-105-22-F-D-VS-K
DAUGHTER-ANALOG
J11A (TOP) = SAM_TSM-110-01-L-DV-P
J11B (BOTTOM) = SAM_SSW-110-22-F-D-VS-K
+5VA
+5VD
JMP1
1
2
+VA
+5VA
AGND
+1.8VD
+3.3VD
-VA
-5VA
DGND
VD1
+5VD
2
4
6
8
10
GPIO0
DGND
GPIO1
GPIO2
DGND
GPIO3
GPIO4
SCL
DGND
SDA
SCLK
SS
P3.3
J12A (TOP) = SAM_TSM-110-01-L-DV-P
J12B (BOTTOM) = SAM_SSW-110-22-F-D-VS-K
TP8
DGND
+5VA
TP2
10uF
C2
+5VD
TP3
10uF
C3
TP4
10uF
JMP3
PWR_DWN
INT
JMP4
MISO
+3.3VD
MOSI
R1
R21
390
J1
-5VA
R22
390
SCL
2.7K
J2
+5VA
D6
SML-LX0603GW-TR
D7
SML-LX0603GW-TR
GREEN
GREEN
J3
+5VD
TP5
+1.8VD
C
RESET
IOVDD
2
C1
P3.5
P1.0
1
-5VA
P3.4
+5VD
JMP2
1
2
TP1
JMP5
2
4
6
8
10
12
14
16
18
20
-5VA
DAUGHTER-POWER
TP7
AGND
JPR-2X1
C
CNTL
CLKX
CLKR
FSX
FSR
DX
DR
INT
TOUT
GPIO5
DAUGHTER-SERIAL
J13
1
3
5
7
9
1
3
5
7
9
11
13
15
17
19
2
A0(-)
A1(-)
A2(-)
A3(-)
AGND
AGND
AGND
VCOM
AGND
AGND
1
1
3
5
7
9
11
13
15
17
19
C4
C5
10uF
10uF
J4
+1.8VD
R2
SDA
2.7K
I2SDOUT
J5
+3.3VD
I2SDIN
LRCLK
BCLK
J21
1
3
5
7
9
11
13
15
17
19
B
A0(-)
A1(-)
A2(-)
A3(-)
AGND
AGND
AGND
VCOM
AGND
AGND
J22
A0(+)
A1(+)
A2(+)
A3(+)
A4
A5
A6
A7
REFREF+
2
4
6
8
10
12
14
16
18
20
1
3
5
7
9
11
13
15
17
19
+5VA
DAUGHTER-ANALOG
J21A (TOP) = SAM_TSM-110-01-L-DV-P
J21B (BOTTOM) = SAM_SSW-110-22-F-D-VS-K
+1.8VD
+VA
+5VA
AGND
+1.8VD
+3.3VD
GPIO0
DGND
GPIO1
GPIO2
DGND
GPIO3
GPIO4
SCL
DGND
SDA
2
4
6
8
10
12
14
16
18
20
P1.1
B
P1.2
P1.3
MCLK
DAUGHTER-SERIAL
J23
1
3
5
7
9
CNTL
CLKX
CLKR
FSX
FSR
DX
DR
INT
TOUT
GPIO5
-VA
-5VA
DGND
VD1
+5VD
2
4
6
8
10
-5VA
J22A (TOP) = SAM_TSM-110-01-L-DV-P
J22B (BOTTOM) = SAM_SSW-110-22-F-D-VS-K
DAUGHTER-POWER
+3.3VD
+5VD
J23A (TOP) = SAM_TSM-105-01-L-DV-P
J23B (BOTTOM) = SAM_SSW-105-22-F-D-VS-K
ti
A
DATA ACQUISITION PRODUCTS
A
HIGH-PERFORMANCE ANALOG DIVISION
SEMICONDUCTOR GROUP
6730 SOUTH TUCSON BLVD., TUCSON, AZ 85706 USA
TITLE
ENGINEER
RICK DOWNS
DRAWN BY
ROBERT BENJAMIN
USB-MODEVM INTERFACE
DOCUMENT CONTROL NO. 6463996
SHEET 2
1
2
3
4
5
OF
2
FILE
SIZE B
DATE 10-Jun-2004
REV A
G:\USB Motherboard - Modular Evm\Schematic\USB Motherboard - ModEvm.ddb - Docume
6
EVALUATION BOARD/KIT IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have
electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental
measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does
not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling
(WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or
services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI’s environmental and/or
safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio
frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are
designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input voltage range of 1-2 V to 3-6 V and the output voltage range of 0 V to 3.6 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions
concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM.
Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than 30°C. The EVM is designed to operate
properly with certain components above 85°C as long as the input and output ranges are maintained. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during operation,
please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising