Texas Instruments | ADS8383 EVM | User Guides | Texas Instruments ADS8383 EVM User guides

Texas Instruments ADS8383 EVM User guides
ADS8383EVM
User’s Guide
December 2003
Data Acquistion
SLAU119
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third−party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products & application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Secruity
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated
EVM IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION
PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided
may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective
considerations, including product safety measures typically found in the end product incorporating the goods.
As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic
compatibility and therefore may not meet the technical requirements of the directive.
Should this evaluation kit not meet the specifications indicated in the EVM User’s Guide, the kit may be returned
within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE
WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED,
IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user
indemnifies TI from all claims arising from the handling or use of the goods. Please be aware that the products
received may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). Due to the open construction
of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic
discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE
TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not
exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein.
Please read the EVM User’s Guide and, specifically, the EVM Warnings and Restrictions notice in the EVM
User’s Guide prior to handling the product. This notice contains important safety information about temperatures
and voltages. For further safety concerns, please contact the TI application engineer.
Persons handling the product must have electronics training and observe good laboratory practice standards.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any
machine, process, or combination in which such TI products or services might be or are used.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input voltage range of ±6 V and the output voltage
range of 0 V and 5.5 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible
damage to the EVM. If there are questions concerning the input range, please contact a TI
field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or
possible permanent damage to the EVM. Please consult the EVM User’s Guide prior to
connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than
60°C. The EVM is designed to operate properly with certain components above 60°C as long
as the input and output ranges are maintained. These components include but are not limited
to linear regulators, switching transistors, pass transistors, and current sense resistors. These
types of devices can be identified using the EVM schematic located in the EVM User’s Guide.
When placing measurement probes near these devices during operation, please be aware
that these devices may be very warm to the touch.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated
Related Documentation From Texas Instruments
Preface
About This Manual
This users guide describes the characteristics, operation, and use of the
ADS8383 18-bit, 500 kHz parallel interface analog to digital converter
evaluation board. A complete circuit description as well as schematic diagram
and bill of materials is included.
How to Use This Manual
This document contains the following chapters:
- Chapter 1 – EVM Overview
- Chapter 2 – Analog Interface
- Chapter 3 – Digital Interface
- Chapter 4 – Power Supply Requirements
- Chapter 5 – Using the EVM
- Chapter 6 − ADS8383EVM BOM, Layout and Schematic
Related Documentation From Texas Instruments
To obtain a copy of any of the following TI documents, call the Texas
Instruments Literature Response Center at (800) 477−8924 or the Product
Information Center (PIC) at (972) 644−5580. When ordering, identify this
booklet by its title and literature number. Updated documents can also be
obtained through our website at www.ti.com
Data Sheets:
ADS8383
REF3040
REF3020
SN74AHC138
SN74AHC245
SN74AHC1G04
THS4031
Literature Number:
SLAS005
SBVS032
SBVS032
SCLS258
SCLS230
SCLS318
SLOS224
iii
Contents
FCC Warning
This equipment is intended for use in a laboratory test environment only. It generates, uses, and can radiate radio frequency energy and has not been tested
for compliance with the limits of computing devices pursuant to subpart J of
part 15 of FCC rules, which are designed to provide reasonable protection
against radio frequency interference. Operation of this equipment in other environments may cause interference with radio communications, in which case
the user at his own expense will be required to take whatever measures may
be required to correct this interference.
iv
Contents
1
EVM Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
2
Analog Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1
Signal Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
3
Digital Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
4
Power Supply Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5
Using the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1
As a Reference Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
As a Prototype Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3
As a Software Test Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5-2
5-2
5-2
6
ADS8383EVM BOM, Layout, and Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1
ADS8383EVM Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
ADS8383EVM Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3
ADS8383EVM Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1
6-2
6-5
6-6
v
Contents
2−1
6−1
6−2
6−3
6−4
Input Buffer Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Top Layer—Layer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground Plane—Layer 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Plane— Layer 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bottom Layer—Layer 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
6-5
6-5
6-5
6-5
2−1
2−2
3−1
3−2
3−3
3−4
4−1
4−2
6−1
vi
Analog Input Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sholder Short Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pinout for Parallel Control Connector P2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Bus Connector P3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pinout for Converter Control Connector J4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Connector, J1, Pin Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADS8383EVM Bill Of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-3
3-1
3-2
3-2
3-2
4-1
4-1
6-2
Chapter 1
This chapter contains the features of the ADS8383EVM.
Topic
1.1
Page
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
EVM Overview
1-1
Features
1.1 Features
- Full-featured evaluation board for the high-speed ADS8383 18-bit, single
channel, parallel interface SAR type analog to digital converters.
- Onboard signal conditioning
- Onboard reference
- Input and output digital buffer
- Onboard decoding for stacking multiple EVMs
1-2
Chapter 2
The ADS8383 analog-to-digital converter has both a positive and negative
analog input pin. The EVM provides ground for the negative input close the device via SJP3, or allows a user-furnished ground wire. The negative input pin
has a range of –200 mV up to 200 mV, and is shorted on the EVM via SJP3.
A signal for the positive input pin can be applied at connector P1, pin 2 (shown
in Table 2−1 ), or applied to the center pin of SMA connector J2.
Table 2−1. Analog Input Connector
Description
Signal Name
Pin tied to Ground
Reserved
Reserved
Reserved
Pin tied to Ground
Pin tied to Ground
Reserved
Pin tied to Ground
Pin tied to Ground
Reserved
AGND
N/A
N/A
N/A
AGND
AGND
N/A
AGND
AGND
N/A
Connector.Pin#
P1.1
P1.3
P1.5
P1.7
P1.9
P1.11
P1.13
P1.15
P1.17
P1.19
P1.2
P1.4
P1.6
P1.8
P.10
P1.12
P1.14
P1.16
P1.18
P1.20
Signal Name
Description
+
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
REF+
Noninverting Input Channel
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
External Reference Input
Topic
Page
2.1
Signal Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Analog Interface
2-1
Signal Conditioning
2.1 Signal Conditioning
The factory recommends the analog input to any SAR type converter be
buffered and low-pass filtered. It is important to note that the input buffer circuit
of the ADS8383EVM, shown in Figure 2−1, utilizes the THS4031 configured
as an inverting gain of one. The amplifier is not stable in a conventional a
gain-of-one configuration. The THS4031 was selected for it’s low noise, high
slew rate and fast settling time. The low pass filter resistor and capacitor values
were selected such that ADS8383EVM would meet the 100 kHz AC
performance specifications listed in the data sheet. The series resistor works
in conjunction with the capacitor to filter the input signal, but also isolates the
amplifier from the 6800 pF capacitive load. The capacitor to ground at the input
of the A/D works in conjunction with the series resistor to filter the input signal,
and acts like a charge reservoir. This external filter capacitor works with the
amplifier to charge the internal sampling capacitor during sampling mode.
The EVM has a provision to offset the input voltage by adjusting R23, a 10-kΩ
potentiometer.
Figure 2−1. Input Buffer Circuit
1 kΩ
1 kΩ
−VCC
VI
0.1 µF
1 µF
4.096 V
−
10 Ω
THS4031
+
10 kΩ
500 Ω
(+) IN
1 µF
6800 pF
0.1 µF
0.22 µF
(−) IN
+VCC
2-2
Reference
2.2 Reference
The ADS8383EVM provide an onboard 4.096-V reference circuit. The EVM
also has the provision for users to supply a reference voltage via connecter P1
pin 20. This reference voltage may be filtered by installing amplifier U1. The
converter itself has onboard reference buffer, therefore it is not necessary to
buffer externally. The reference buffer circuit on the EVM is not populated with
an amplifier. The EVM allows users to select from two reference sources. Set
SJP1 and SJP2 to select onboard reference voltage (REF3040) or a
user-supplied reference voltage via P1 pin 20. See Table 2−2 for jumper
settings. See Chapter 6 for the full schematic.
Table 2−2. Solder Short Jumper Setting
Jumper Setting
Reference
Designator
Description
1−2
2−3
Select REF3040 output for reference voltage
Installed†
Not installed
Select buffered reference voltage
Not installed
Installed
Select U3, REF3040, as 4.096V reference
Installed†
Buffer User supplied reference voltage
Not Installed
Installed
SJP3
Short (−)IN pin to ground
Installed†
N/A
SJP4
Apply offset voltage to A/D buffer
Not Installed
N/A
SJP5
Set amplifier U1 negative supply to ground
Installed
Set amplifier U1 negative supply to −VCC
Not Installed
Installed†
Set amplifier U2 negative supply to ground
Installed
Not Installed
Set amplifier U2 negative supply to −VCC
Not Installed
Installed†
SJP1
SJP2
SJP6
† Factory set condition
Analog Interface
2-3
2-4
Chapter 3
The ADS8383EVM is designed for easy interfacing to multiple platforms.
Samtec part numbers SSW−110−22−F−D−VS−K and TSM−110−01−T−DV−P
provide a convenient dual row header/socket combination at P2 and P3.
Consult Samtec at www.samtec.com or 1−800−SAMTEC−9 for a variety of
mating connector options.
Table 3−1. Pinout for Parallel Control Connector P2
Connector.Pin
Signal
P2.1
DC_CS
Description
Daughter card Board Select pin
P2.3
P2.5
P2.7
A0
Address line from processor
P2.9
A1
Address line from processor
P2.11
A2
Address line from processor
P2.13
P2.15
P2.17
P2.19
Note:
INTc
Set jumper W3 to select BUSY or inverted signal
to be applied to this pin.
All even numbered pins of P2 are tied to DGND.
Read (RD) and conversion start (CONVST) signals to the converter can be
assigned to two different addresses in memory via jumper settings. This allows
for the stacking of up to two ADS8383EVMs into processor memory. See
Table 3−2 for jumper settings. Note, the evaluation module does not allow chip
select (CS) line of the converter to be assigned to different memory locations.
It is therefore suggested the CS line be grounded or wired to an appropriate
signal of the processor.
Digital Interface
3-1
Table 3−2. Jumper Settings
Jumper Settings
Reference Designator
W1
W2
W3
Description
1−2
2−3
Set A[2..0] = 0x1 to generate RD pulse
Installed†
Not installed
Set A[2..0] = 0x2 to generate RD pulse
Not installed
Installed
Set A[2..0] = 0x3 to generate CONVST pulse
Installed†
Not installed
Set A[2..0] = 0x4 to generate CONVST pulse
Not installed
Installed
Apply BUSY to P3 pin 19
Not installed
Installed†
Apply inverted BUSY to P3 pin 19
Installed†
Not installed
† Factory set condition
The data bus is available at connector P3, see Table 3−3 for pin out
information.
Table 3−3. Data Bus Connector P3
Connector.Pin
Signal
P3.1
D0
Buffered Data Bit 0 (LSB)
P3.3
D1
Buffered Data Bit 1
P3.5
D2
Buffered Data Bit 2
P3.7
D3
Buffered Data Bit 3
Note:
Description
P3.9
D4
Buffered Data Bit 4
P3.11
D5
Buffered Data Bit 5
P3.13
D6
Buffered Data Bit 6
P3.15
D7
Buffered Data Bit 7
P3.17
D8
Buffered Data Bit 8
P3.19
D9
Buffered Data Bit 9
P3.21
D10
Buffered Data Bit 10
P3.23
D11
Buffered Data Bit 11
P3.25
D12
Buffered Data Bit 12
P3.27
D13
Buffered Data Bit 13
P3.29
D14
Buffered Data Bit 14
P3.31
D15
Buffered Data Bit 15
P3.33
D16
Buffered Data Bit 16
P3.35
D17
Buffered Data Bit 17 (MSB)
All even numbered pins of P3 are tied to DGND.
This evaluation module provides direct access to all the analog-to-digital
converter control signals via connector J4, see Table 3−4.
Table 3−4. Pinout for Converter Control Connector J4
Connector.Pin
Signal
J4.1
CS
Chip Select pin. Active low
J4.3
RD
Read pin. Active low
J4.5
CONVST
J4.7
BYTE
J4.9
BUS 18/16
J4.11
BUSY
Note:
3-2
Description
Convert start pin. Active low
Byte select input. Used for 8-bit bus reading.
Bus size select input. Used for selecting 18-bit or 16-bit wide bus transfer.
Converter Status Output. High when a conversion is in progress.
All even numbered pins of P4 are tied to DGND.
Chapter 4
!""# $ %
The EVM accepts four power supplies.
- A dual ±Vs DC supply for the dual supply op−amps. Recommend ±6VDC
supply.
- A single +5.0 V DC supply for analog section of the board (A/D + Refer-
ence).
- A single +5.0 V or +3.3 VDC supply for digital section of the board (A/D +
address decoder + buffers).
There are two ways to provide these voltages.
1) Wire in the voltages at test points on the EVM. See Table 4−1.
Table 4−1. Power Supply Test Points
Test Point
Signal
Description
TP16
+BVDD
Apply +3.3 V or +5.0 V. See ADC datasheet for full range.
TP20
+AVCC
Apply +5.0 V.
TP14
+VA
Apply +6.0 V. Positive supply for amplifier.
TP18
−VA
Apply –6.0 V. Negative supply for amplifier.
2) Use the power connector J1, and derive the voltages elsewhere. The
pinout for this connector is shown below. If using this connector, set W4
jumper to connect +3.3 V or +5 V from connector to +BVDD. Short
between pins 1−2 to select +5 VD, or short between pins 2−3 to select
+3.3 VD as the source for the digital buffer voltage supply (+BVDD).
Table 4−2. Power Connector, J1, Pin Out
Signal
Power Connector − J1
Signal
+VA(+6V)
1
2
–VA (–6V)
+5VA
3
4
N/C
DGND
5
6
AGND
N/C
7
8
N/C
+3.3VD
9
10
+5VD
Power Supply Requirements
4-1
4-2
Chapter 5
& The ADS8383EVM serves three functions
1) As a reference design
2) As a prototype board and
3) As software test platform
Topic
Page
5.1
As a Reference Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.2
As a Prototype Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.3
As a Software Test Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Using the EVM
5-1
As a Reference Board
5.1 As a Reference Board
As a reference design, the ADS8383EVM contains the essential circuitry to
showcase the analog-to-digital converter. This essential circuitry includes the
input amplifier, reference circuit, and buffers. The EVM analog input circuit is
optimized for 100 kHz sine wave, therefore users may need to adjust the
resistor and capacitor values of the A/D input RC circuit. In AC type
applications where signal distortion is a concern, polypropylene capacitors
should be used in the signal path.
5.2 As a Prototype Board
As a prototype board, the buffer circuit consists of footprint is a standard 8-pin
SOIC and resistor pads for inverting and noninverting configurations. The
ADS8383EVM can be used to evaluate both dual and single supply amplifiers.
The EVM comes installed with a dual supply amplifier as it allows the user to
take advantage of the full input voltage range of the converter. For applications
that require signal supply operation and smaller input voltage range, the
THS4031 can be replaced with the single supply amplifier like OPA300. Pad
jumper SJP6 should be shorted between pads 1 and 2, as it shorts the minus
supply pin of the amplifier to ground. Positive supply voltage can be applied
via test point TP14 or connector J1 pin 1.
5.3 As a Software Test Platform
As a software test platform, connectors P1, P2, P3 plug into the parallel
interface connectors of the 5−6K interface card. The 5−6K interface card sits
on the C5000 and C6000 Digital Signal Processor starter kit (DSK). The
ADS8383EVM is then mapped into the processor’s memory space. This card
also provides an area for signal conditioning. This area can be used to install
application circuit(s) for digitization by the ADS8383 analog-to-digital
converter. Refer to the 5−6K interface card user’s guide (SLAU104) for more
information.
For the software engineer the ADS8383EVM provides a simple platform for
interfacing to the converter. The EVM provides standard 0.1” headers and
sockets to wire into prototype boards. The user need only provide in 3 address
lines (A2, A1, A0) and address valid line(DC_CS) to connector P2. To choose
which address combinations will generate RD and CONVST set jumpers as
shown in Table 3−2. Recall chip select (CS) signal is not memory mapped or
tied to P2, therefore it must be controlled via general purpose pin or shorted
to ground at J3 pin 1. If address decoding is not required, the EVM provides
direct access to converter data bus via P3 and control via J3.
5-2
Chapter 6
!'('( )* +# * !% This chapter contains the ADS8383EVM bill of materials, the layouts, and the
schematic.
Topic
Page
6.1
ADS8383EVM Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.2
ADS8383EVM Layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
6.3
ADS8383EVM Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
ADS8383EVM BOM, Layout, and Schematic
6-1
ADS8383EVM Bill of Materials
6.1 ADS8383EVM Bill of Materials
Table 6−1 contains a complete bill of materials for the ADS8383EVM. The
schematic diagram is also provided for reference. Contact the Product
Information Center or e−mail dataconvapps@list.ti.com for questions
regarding this EVM.
Table 6−1. ADS8383EVM Bill Of Materials
Item
No.
QTY
1
2
0
R4 R21
Panasonic − ECG or
Alternate
ERJ−3GEY0R00V
Resistor 0 Ω 1/16W 5% 0603
SMD
2
1
0
R1
Panasonic − ECG or
Alternate
ERJ−6GEY0R00V
Resistor 0.0 Ω 1/10W 5%
0805 SMD
3
1
10
R13
Panasonic − ECG or
Alternate
ERJ−6ENF10R0V
Resistor 10.0 Ω 1/10W 1%
0805 SMD
4
1
50
R24
Panasonic − ECG or
Alternate
ERJ−6ENF49R9V
Resistor 49.9 Ω 1/10W 1%
0805 SMD
5
2
100
R14 R15
Panasonic − ECG or
Alternate
ERJ−3EKF1000V
Resistor 100 Ω 1/16W 1%
0603 SMD
6
1
100
R25
Panasonic − ECG or
Alternate
ERJ−6ENF1000V
Resistor 100 Ω 1/10W 1%
0805 SMD
7
1
499
R2
Panasonic − ECG or
Alternate
ERJ−6ENF4990V
Resistor 499 Ω 1/10W 1%
0805 SMD
8
2
1k
R6 R10
Panasonic − ECG or
Alternate
ERJ−6ENF1001V
Resistor 1.00 kΩ 1/10W 1%
0805 SMD
9
5
10k
R16 R17
R18 R19
R20
Panasonic − ECG or
Alternate
ERJ−3EKF1002V
Resistor 10.0 kΩ 1/16W 1%
0603 SMD
10
1
10k
R7
Panasonic − ECG or
Alternate
ERA−S15J103V
Resistor 10 kΩ 1/10W 1500
PPM 5%0805
Value
Reference
Designators
Mfg
Mfg’s Part Number
Description
11
1
NI
R3
NOT INSTALLED
NOT INSTALLED
12
1
NI
R11
NOT INSTALLED
NOT INSTALLED
13
4
1 nF
C3 C5
C11 C23
Kemet or Alternate
C1206C102J5GACTU
Capacitor 1000 pF 50V
ceramic NPO 1206
14
1
6800 pF
C39
WIMA or Alternate
MKP2 6800/630/5
6800 pF polypropylene
capacitor
15
9
0.01 µF
C21 C41
C44 C46
C48 C53
C56 C65
C50
Kemet or Alternate
C0603C103J5RACTU
Capaciator 10000 pF 50V
Ceramic X7R 0603
16
2
0.01 µF
C10 C20
Kemet or Alternate
C0805C103K5RACTU
Capacitor 10000 pF 50V
Ceramic X7R 0805
17
2
0.01 µF
C4 C26
Kemet or Alternate
C1206C103J5RACTU
Capacitor 10000 pF 50V
Ceramic X7R 1206
18
14
0.1 µF
C25 C40
C42 C43
C47 C51
C52 C54
C55 C57
C58 C59
C64 C38
Kemet or Alternate
C0603C104K3RACTU
Capacitor 0.1 µF 25V
Ceramic X7R 0603
6-2
ADS8383EVM Bill of Materials
Reference
Designators
Item
No.
QTY
19
7
0.1 µF
C7 C9 C15
C22 C32
C34 C36
20
4
1 µF
21
2
22
Value
Mfg
Mfg’s Part Number
Description
Kemet or Alternate
C0805C104J5RACTU
Capacitor .10 µF 50V
ceramic X7R 0805
C8 C16
C31 C37
Panasonic − ECG or
Alternate
ECJ−GVB1C105K
Capacitor 1 µF 16V ceramic
X5R 0805
1 µF
C2 C28
Kemet or Alternate
C1206C105K3RACTU
Capacitor 1.0 µF 25V
ceramic X7R 1206
1
0.22 µF
C33
Panasonic − ECG or
Alternate
ECJ−2VB1C224K
Capacitor 0.22 µF 16V
ceramic X7R 0805
23
2
0.47 µF
C61 C63
Panasonic − ECG or
Alternate
ECJ−1VF1C474Z
Capacitor 0.47 µF 16V
ceramic Y5V 0603
24
1
10 µF
C62
Panasonic − ECG or
Alternate
ECJ−2FF1A106Z
Capacitor 10 µF 10V ceramic
F 0805
25
4
10 µF
C1 C6 C12
C19
Panasonic − ECG or
Alternate
ECJ−3YB1C106M
Capacitor 10 µF 16V ceramic
X5R 1206
26
5
10 µF
C14 C24
C27 C29
C49
Kemet or Alternate
T491B106K016AS
Capacitor TANT 10 µF 16V
10% SMT
27
1
22 µF
C17
Panasonic − ECG or
Alternate
ECJ−3YB0J226M
Capacitor 22 µF 6.3V
ceramic X5R 1206
28
4
NI
C13 C18
C45 C60
NOT INSTALLED
NOT INSTALLED
29
3
NI
C30 C35 R5
NOT INSTALLED
NOT INSTALLED
30
2
1K
RP1 RP3
CTS Corporation
742C163102JTR
RES ARRAY 1K OHM
16TERM 8RES SMD
31
1
100
RP2
CTS Corporation
742C163101JTR
RES ARRAY 100 OHM
16TRM 8RES SMD
32
1
1K
RP4
CTS Corporation
744C083102JTR
RES ARRAY 1K OHM
8TERM 4RES SMD
33
1
10k
R23
Bourns
3214W−1−103E
TRIMPOT 10K OHM 4MM
TOP ADJ SMD
34
4
BLM21AJ601SN
1L
L1 L2 L3
L4
Murata ERIE
BLM31PG601SN1L
Chip ferrite beads− 600 Ω at
100 MHz
35
1
OPA627
U1
NOT INSTALLED
NOT INSTALLED
Amplifier
36
1
THS4031
U2
Texas Instruments
THS4031IDR
100−MHz low-noise
high-speed amplifier
37
1
REF3040
U3
Texas Instruments
REF3040AIDBZT
REF3040 50 ppm/°C, 50 µA
in SOT23−3 CMOS voltage
reference
38
1
ADS8383
U4
Texas Instruments
ADS8383IPFB
ADS8383 18-bIT 500 KSPS
39
4
SN74AHC245P
WR
U5 U6 U7
U8
Texas Instruments
SN74AHC245PWR
Octal bus transceiver, 3-state
40
1
SOIC-8
Footprint
U9
NOT INSTALLED
NOT INSTALLED
Footprint for 8 pin SOIC
reference that operates from
+5V.
41
1
REF3020
U10
Texas Instruments
REF3020AIDBZT
REF3020 50 ppm/°C, 50 µA
in SOT23−3 CMOS voltage
reference
42
1
SN74AHC138P
WR
U11
Texas Instruments
SN74AHC138PWR
3-Line to 8-Line decoder/
demultiplexer
ADS8383EVM BOM, Layout, and Schematic
6-3
ADS8383EVM Bill of Materials
Reference
Designators
Item
No.
QTY
Value
43
1
SN74AHC1G04
DBV
U12
Texas Instruments
SN74AHC1G04DBVR
Single inverter gate
44
1
5X2X.1
J1
Samtec
SSW−105−22−S−D−VS
0.025” SMT socket − bottom
side of PWB
Samtec
TSM−105−01−T−D−V−P 0.025” SMT plug − top side of
PWB
Mfg
Mfg’s Part Number
Description
45
1
SMA_PCB_MT
J2
Johnson
Components Inc.
142−0701−301
Right angle SMA connector
46
1
6X2X.1
J4
Samtec
SSW−106−22−S−D−VS
0.025” SMT socket − bottom
side of PWB
Samtec
TSM−106−01−T−D−V−P 0.025” SMT plug − top side of
PWB
Samtec
SSW−118−22−S−D−VS
0.025” SMT socket − bottom
side of PWB
Samtec
TSM−118−01−T−D−V−P
0.025” SMT plug − top side of
PWB
Samtec
SSW−110−22−S−D−VS
0.025” SMT socket − bottom
side of PWB
Samtec
TSM−110−01−T−D−V−P
0.025” SMT plug − top side of
PWB
47
48
1
2
18X2X.1_SMT_
PLUG_&_
SOCKET
P3
10X2X.1
P1 P2
49
2
SJP2
SJP3 SJP4
NOT INSTALLED
NOT INSTALLED
Pad 2 position jumper
50
4
SJP3
SJP1 SJP2
SJP5 SJP6
NOT INSTALLED
NOT INSTALLED
Pad 3 Postion jumper
51
4
3POS_JUMPER
W1 W2
W3 W4
Samtec
TSW−103−07−L−S
3 Position jumper _ 0.1”
spacing
52
16
TP_0.025
TP1 TP2
TP3 TP4
TP5 TP6
TP7 TP8
TP9 TP14
TP15 TP16
TP17 TP18
TP19 TP20
Keystone Electronics
5000K–ND
Test point − single 0.025” pin
6-4
ADS8383EVM Layout
6.2 ADS8383EVM Layout
Figure 6−1. Top Layer—Layer 1
Figure 6−2. Ground Plane—Layer 2
ADS8383EVM BOM, Layout, and Schematic
6-5
ADS8383EVM Layout
Figure 6−3. Power Plane—Layer 3
Figure 6−4. Bottom Layer—Layer 4
6-6
ADS8383EVM Schematic
6.3 ADS8383EVM Schematic
The schematic follows this page.
ADS8383EVM BOM, Layout, and Schematic
6-7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising