Texas Instruments | LM137HVQML 3-Terminal Adjustable Negative Regulators (High Voltage) (Rev. A) | Datasheet | Texas Instruments LM137HVQML 3-Terminal Adjustable Negative Regulators (High Voltage) (Rev. A) Datasheet

Texas Instruments LM137HVQML 3-Terminal Adjustable Negative Regulators (High Voltage) (Rev. A) Datasheet
LM137HVQML
www.ti.com
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
LM137HVQML 3-Terminal Adjustable Negative Regulators (High Voltage)
Check for Samples: LM137HVQML
FEATURES
1
•
•
2
•
•
•
•
•
•
•
•
•
•
Output Voltage Adjustable from −47V to −1.2V
1.5A Output Current Specified, −55°C ≤ TJ ≤
+150°C
Line Regulation Typically 0.01%/V
Load Regulation Typically 0.3%
Excellent Thermal Regulation, 0.002%/W
77 dB Ripple Rejection
Excellent Rejection of Thermal Transients
50 ppm/°C Temperature Coefficient
Temperature-Independent Current Limit
Internal Thermal Overload Protection
Standard 3-Lead Transistor Package
Output Short Circuit Protected
DESCRIPTION
The LM137HV is an adjustable 3-terminal negative
voltage regulator capable of supplying in excess of
−1.5A over an output voltage range of −47V to −1.2V.
This regulators is exceptionally easy to apply,
requiring only 2 external resistors to set the output
voltage and 1 output capacitor for frequency
compensation. The circuit design has been optimized
for excellent regulation and low thermal transients.
Further, the LM137HV features internal current
limiting,
thermal
shutdown
and
safe-area
compensation, making them virtually blowout-proof
against overloads.
The LM137HV serves a wide variety of applications
including local on-card regulation, programmableoutput voltage regulation or precision current
regulation. The LM137HV is an ideal complement to
the LM117HV adjustable positive regulator.
Connection Diagrams
See Physical Dimensions section for further information
Figure 1. TO Package – Bottom View
See Package Number NDT0003A
Figure 2. TO-3 Package (Bottom View)
See Package Number K
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2013, Texas Instruments Incorporated
LM137HVQML
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
www.ti.com
Typical Applications
†
C1 = 1 μF solid tantalum or 10 μF aluminum electrolytic required for stability. Output capacitors in the range of 1 μF
to 1000 μF of aluminum or tantalum electrolytic are commonly used to provide improved output impedance and
rejection of transients.
*
C2 = 1 μF solid tantalum is required only if regulator is more than 4″ from power-supply filter capacitor.
Figure 3. Adjustable Negative Voltage Regulator
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1)
Power Dissipation (2)
Internally limited
Input—Output Voltage Differential
50V
−55°C ≤ TA ≤
+125°C
Operating Ambient Temperature Range
Maximum Junction Temperature Range
+150°C
−65°C ≤ TA ≤
+150°C
Storage Temperature
Lead Temperature (Soldering, 10 sec.)
Thermal Resistance
θJA
θJC
300°C
NDT0003A pkg. (Still Air @ 0.5W)
174°C/W
NDT0003A pkg. (500LF / Min Air Flow @ 0.5W)
64°C/W
K pkg. (Still Air @ 0.5W)
42°C/W
K pkg. (500LF / Min Air Flow @ 0.5W)
14°C/W
NDT0003A pkg. (@ 1.0W)
15°C/W
K pkg.
4°C/W
Package Weight (Typical)
NDT0003A pkg
K pkg
ESD Rating (3)
(1)
(2)
(3)
2
955mg
12,750mg
4000V
“Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature),
θJA (package junction to ambient thermal resistance, and TA (ambient temperature). The maximum allowable power dissipation at any
temperature is PDmax = (TJmax − TA) / θJA or the number given in the Absolute Maximum Ratings, whichever is lower.
Human body model, 100pF discharged through 1.5KΩ
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
LM137HVQML
www.ti.com
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
Table 1. Quality Conformance Inspection
Mil-Std-883, Method 5004 and Method 5005
(1)
Subgroup (1)
Description
1
Static tests at
+25°C
2
Static tests at
+125°C
Temp (°C)
3
Static tests at
-55°C
4
Dynamic tests at
+25°C
5
Dynamic tests at
+125°C
6
Dynamic tests at
-55°C
7
Functional tests at
+25°C
8A
Functional tests at
+125°C
8B
Functional tests at
-55°C
9
Switching tests at
+25°C
10
Switching tests at
+125°C
11
Switching tests at
-55°C
Group “A” sample only, test at all temperature.
LM137HVH 883 Electrical Characteristics DC Parameters
The following conditions apply, unless otherwise specified. VIN = −4.0V, IO = 0.53A, VO = VRef
Symbol
Parameter
Conditions
Notes
VIN = -4.25V, IO = 8 mA
VRef
RLine
Line Regulation
IAdj
Adjustment Pin Current
ΔIAdj
Adjustment Pin Current Change
RLoad
Load Regulation
VRth
Thermal Regulation
ICL
(1)
Current Limit
Unit
Subgroups
-1.272
-1.23
V
1
2, 3
-1.28
-1.225
V
-1.23
V
1
-1.28
-1.225
V
2, 3
VO = -1.7V, VIN = -4.25V
3.0
mA
1, 2, 3
VO = -1.7V, VIN = -11.75V
3.0
mA
1, 2, 3
VO = -1.7V, VIN = -42V
5.0
mA
1, 2, 3
-42V ≤ VIN ≤ -4.25V, IO = 8mA
9.4
mV
1, 2, 3
VIN = -42V, IO = 8mA
100
µA
1, 2, 3
VIN = -4.25V, IO = 8mA
100
µA
1, 2, 3
VIN = -54V, IO = 8mA
100
µA
1
-42V ≤ VIN ≤ -4.25V, IL = 8mA
6.0
µA
1, 2, 3
VIN = -6.25V, 8mA ≤ IO ≤ 0.53A
5.0
µA
1, 2, 3
-54V ≤ VIN ≤ -4.25V, IO = 8mA
6.0
µA
1
VIN = -54V, 10mA ≤ IO ≤ 60mA
25
mV
1
VIN = -6.25V, 8mA ≤ IO ≤ 0.53A
25
mV
1
IO = 0.53A, VIN = -14.5V
5
mV
1
VIN = -42V, IO = 8mA
Minimum Load Current
Max
-1.272
Reference Voltage
IQ
Min
VIN ≤ -14.25
VIN = -51.25V
See (1)
0.5
1.6
A
1
(1)
0.1
0.5
A
1
See
Specified parameter not tested.
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
3
LM137HVQML
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
www.ti.com
LM137HVH 883 Electrical Characteristics AC Parameters
Symbol
RR
Parameter
Ripple Rejection
Conditions
VIN = -6.25V, VO = VRef, f = 120Hz,
eI = 1VRMS, IL = 125mA
Notes
Min
See (1) (2)
Max
Unit
Subgroups
66
dB
4, 5, 6
Tested at +25°C, specified, but not tested at +125°C and −55°C
Bench test per (SG)RPI-3–362 Use TDN 70256657 (NSSG)
(1)
(2)
LM137HVK 883 Electrical Characteristics DC Parameters
The following conditions apply, unless otherwise specified. VIN = −40V, IL = 8.0mA, VO = VRef = −1.25V (nominal)
Symbol
Parameter
Conditions
Notes
VIN = -4.25V
VRef
Reference Voltage
RLine
Line Regulation
RLoad
Load Regulation
VRth
Thermal Regulation
IAdj
Adjustment Pin Current
ΔIAdj
Adjustment Pin Current Change
IQ
Minimum Load Current
ISC
Short Circuit
Subgroups
Max
Unit
1.272
-1.23
V
1
-1.28
-1.225
V
2, 3
VIN = -42V
-1.272
-1.23
V
1
VIN = -41.3V
-1.28
-1.225
V
2, 3
9.4
mV
1
2, 3
-42V ≤ VIN ≤ -4.25V
-41.3V ≤ VIN ≤ -4.25V
9.4
mV
VIN = -54V, 10mA ≤ IO ≤ 110mA
-25
25
mV
1
VIN = -6.25V, 8mA ≤ IO ≤ 1.5A
-25
25
mV
1, 2, 3
IO = 1.5A, VIN = -14.5V,
t = 10mS
-5.0
5.0
mV
1
VIN = -42V
100
µA
1
VIN = -41.3V
100
µA
2, 3
VIN = -4.25V
100
µA
1, 2, 3
VIN = -54V
100
µA
1
-42V ≤ VIN ≤ -4.25V
-5.0
5.0
µA
1
-41.3V ≤ VIN ≤ -4.25V
-5.0
5.0
µA
2, 3
-54V ≤ VIN ≤ -4.25V
-6.0
6.0
µA
1
VIN = -6.25V, 8mA ≤ IO ≤ 1.5A
-5.0
5.0
µA
1, 2, 3
VO = 1.7V, VIN = -4.25V
3.0
mA
1, 2, 3
VO = -1.7V, VIN = -11.75V
3.0
mA
1, 2, 3
VO = -1.7V, VIN = -42V
5.0
mA
1
VO = -1.7V, VIN = -41.3V
5.0
mA
2, 3
-2.85
-1.6
A
1
-3.5
-1.6
A
2, 3
-0.8
-0.2
A
1
VIN = -5V
VIN = -51.25V
(1)
Min
See (1)
Specified parameter not tested.
LM137HVK 883 Electrical Characteristics AC Parameters:
The following conditions apply, unless otherwise specified. VIN = −40V, IL = 8.0mA, VO = VRef = −1.25V (nominal)
Symbol
RR
(1)
(2)
4
Parameter
Ripple Rejection
Conditions
Notes
Min
VIN = -6.25V, VO = VRef,
f = 120Hz, ein = 1V RMS,
IL = 0.5A
See (1) (2)
66
Max
Unit
Subgroups
dB
4, 5, 6
Tested at +25°C, specified, but not tested at +125°C and −55°C
Bench test per (SG)RPI-3–362 Use TDN 70256657 (NSSG)
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
LM137HVQML
www.ti.com
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
Schematic Diagram
Thermal Regulation
When power is dissipated in an IC, a temperature gradient occurs across the IC chip affecting the individual IC circuit
components. With an IC regulator, this gradient can be especially severe since power dissipation is large. Thermal regulation
is the effect of these temperature gradients on output voltage (in percentage output change) per Watt of power change in a
specified time. Thermal regulation error is independent of electrical regulation or temperature coefficient, and occurs within 5
ms to 50 ms after a change in power dissipation. Thermal regulation depends on IC layout as well as electrical design. The
thermal regulation of a voltage regulator is defined as the percentage change of VOUT, per Watt, within the first 10 ms after a
step of power is applied. The LM137HV's specification is 0.02%/W, max.
In Figure 4, a typical LM137HV's output drifts only 3 mV (or 0.03% of VOUT = −10V) when a 10W pulse is applied for 10 ms.
This performance is thus well inside the specification limit of 0.02%/W x 10W = 0.2% max. When the 10W pulse is ended, the
thermal regulation again shows a 3 mV step as the LM137HV chip cools off. Note that the load regulation error of about 8 mV
(0.08%) is additional to the thermal regulation error. In Figure 5, when the 10W pulse is applied for 100 ms, the output drifts
only slightly beyond the drift in the first 10 ms, and the thermal error stays well within 0.1% (10 mV).
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
5
LM137HVQML
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
www.ti.com
When power is dissipated in an IC, a temperature gradient occurs across the IC chip affecting the individual IC circuit
components. With an IC regulator, this gradient can be especially severe since power dissipation is large. Thermal regulation
is the effect of these temperature gradients on output voltage (in percentage output change) per Watt of power change in a
specified time. Thermal regulation error is independent of electrical regulation or temperature coefficient, and occurs within 5
ms to 50 ms after a change in power dissipation. Thermal regulation depends on IC layout as well as electrical design. The
thermal regulation of a voltage regulator is defined as the percentage change of VOUT, per Watt, within the first 10 ms after a
step of power is applied. The LM137HV's specification is 0.02%/W, max.
In Figure 4, a typical LM137HV's output drifts only 3 mV (or 0.03% of VOUT = −10V) when a 10W pulse is applied for 10 ms.
This performance is thus well inside the specification limit of 0.02%/W x 10W = 0.2% max. When the 10W pulse is ended, the
thermal regulation again shows a 3 mV step as the LM137HV chip cools off. Note that the load regulation error of about 8 mV
(0.08%) is additional to the thermal regulation error. In Figure 5, when the 10W pulse is applied for 100 ms, the output drifts
only slightly beyond the drift in the first 10 ms, and the thermal error stays well within 0.1% (10 mV).
LM137HV, VOUT = −10V
VIN−VOUT = −40V
IL = 0A→0.25A→0A
Vertical sensitivity, 5 mV/div
Figure 4.
LM137HV, VOUT = −10V
VIN−VOUT = −40V
IL = 0A→0.25A→0A
Horizontal sensitivity, 20 ms/div
Figure 5.
6
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
LM137HVQML
www.ti.com
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
When power is dissipated in an IC, a temperature gradient occurs across the IC chip affecting the individual IC circuit
components. With an IC regulator, this gradient can be especially severe since power dissipation is large. Thermal regulation
is the effect of these temperature gradients on output voltage (in percentage output change) per Watt of power change in a
specified time. Thermal regulation error is independent of electrical regulation or temperature coefficient, and occurs within 5
ms to 50 ms after a change in power dissipation. Thermal regulation depends on IC layout as well as electrical design. The
thermal regulation of a voltage regulator is defined as the percentage change of VOUT, per Watt, within the first 10 ms after a
step of power is applied. The LM137HV's specification is 0.02%/W, max.
In Figure 4, a typical LM137HV's output drifts only 3 mV (or 0.03% of VOUT = −10V) when a 10W pulse is applied for 10 ms.
This performance is thus well inside the specification limit of 0.02%/W x 10W = 0.2% max. When the 10W pulse is ended, the
thermal regulation again shows a 3 mV step as the LM137HV chip cools off. Note that the load regulation error of about 8 mV
(0.08%) is additional to the thermal regulation error. In Figure 5, when the 10W pulse is applied for 100 ms, the output drifts
only slightly beyond the drift in the first 10 ms, and the thermal error stays well within 0.1% (10 mV).
Typical Applications
Full output current not available at high input-output voltages
*The 10 μF capacitors are optional to improve ripple rejection
Figure 6. Adjustable High Voltage Regulator
Figure 7. Current Regulator
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
7
LM137HVQML
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
www.ti.com
When power is dissipated in an IC, a temperature gradient occurs across the IC chip affecting the individual IC circuit
components. With an IC regulator, this gradient can be especially severe since power dissipation is large. Thermal regulation
is the effect of these temperature gradients on output voltage (in percentage output change) per Watt of power change in a
specified time. Thermal regulation error is independent of electrical regulation or temperature coefficient, and occurs within 5
ms to 50 ms after a change in power dissipation. Thermal regulation depends on IC layout as well as electrical design. The
thermal regulation of a voltage regulator is defined as the percentage change of VOUT, per Watt, within the first 10 ms after a
step of power is applied. The LM137HV's specification is 0.02%/W, max.
In Figure 4, a typical LM137HV's output drifts only 3 mV (or 0.03% of VOUT = −10V) when a 10W pulse is applied for 10 ms.
This performance is thus well inside the specification limit of 0.02%/W x 10W = 0.2% max. When the 10W pulse is ended, the
thermal regulation again shows a 3 mV step as the LM137HV chip cools off. Note that the load regulation error of about 8 mV
(0.08%) is additional to the thermal regulation error. In Figure 5, when the 10W pulse is applied for 100 ms, the output drifts
only slightly beyond the drift in the first 10 ms, and the thermal error stays well within 0.1% (10 mV).
Figure 8. Adjustable Current Regulator
*When CL is larger than 20 μF, D1 protects the LM137HV in case the input supply is shorted
**When C2 is larger than 10 μF and −VOUT is larger than −25V, D2 protects the LM137HV is case the output is
shorted
Figure 9. Negative Regulator with Protection Diodes
*Use resistors with good tracking TC < 25 ppm/°C
Figure 10. High Stability −40V Regulator
8
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
LM137HVQML
www.ti.com
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
Typical Performance Characteristics
(H and K-STEEL Package)
Load Regulation
Current Limit
Figure 11.
Figure 12.
Adjustment Current
Dropout Voltage
Figure 13.
Figure 14.
Temperature Stability
Minimum Operating Current
Figure 15.
Figure 16.
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
9
LM137HVQML
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
(H and K-STEEL Package)
10
Ripple Rejection
Ripple Rejection
Figure 17.
Figure 18.
Ripple Rejection
Output Impedance
Figure 19.
Figure 20.
Line Transient Response
Load Transient Response
Figure 21.
Figure 22.
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
LM137HVQML
www.ti.com
SNVS314A – DECEMBER 2010 – REVISED APRIL 2013
REVISION HISTORY
Date Released
Revision
12/16/2010
A
04/17/2013
A
Section
New Release, Corporate format
Changes
2 MDS data sheets converted into one Corp. Data
sheet format. MNLM137HV-K rev 0A0, MNLM137HVH rev 2A0 MDS datasheets will be archived.
Changed layout of National Data Sheet to TI format.
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LM137HVQML
11
PACKAGE OPTION ADDENDUM
www.ti.com
17-Sep-2019
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM137HVH/883
ACTIVE
TO
NDT
3
20
TBD
Call TI
Call TI
-55 to 150
LM137HVK MD8
ACTIVE
DIESALE
Y
0
100
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM120H-15P+
LM137HVH/883 Q ACO
LM137HVH/883 Q >T
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
17-Sep-2019
Addendum-Page 2
MECHANICAL DATA
NDT0003A
H03A (Rev D)
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising