Texas Instruments | FPC402 Quad Port Controller (Rev. A) | Datasheet | Texas Instruments FPC402 Quad Port Controller (Rev. A) Datasheet

Texas Instruments FPC402 Quad Port Controller (Rev. A) Datasheet
Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
FPC402
SNLS583A – JUNE 2017 – REVISED OCTOBER 2017
FPC402 Quad Port Controller
1 Features
3 Description
•
The FPC402 quad port controller serves as a lowspeed signal aggregator for common port types such
as SFP, QSFP, Mini-SAS HD, and others. The
FPC402 aggregates all low-speed control and I2C
signals across four ports and presents a single easyto-use management interface to the host (I2C or SPI).
Multiple FPC402s can be used in high-port-count
applications with one common control interface to the
host. The FPC402 is designed to allow placement on
the bottom side of the PCB, underneath the press fit
connector, to simplify routing. This localized control of
the low-speed signals in the ports cuts system BOM
costs by enabling the use of smaller IO count control
devices (FPGAs, CPLDs, and MCUs) and by
reducing routing layer congestion.
1
•
•
•
•
•
•
•
•
•
•
Control Signal Management and I2C Aggregation
Across Four Ports
Combine Multiple FPC402s to Control 56 Total
Ports Through a Single Host Interface
Eliminate Need for Discrete I2C Muxes, LED
Drivers, and High-Pin-Count FPGA/CPLD Control
Devices
Reduce PCB Routing Complexity by Handling All
Low-Speed Control Signals Close to the Port
Selectable I2C (up to 1 MHz) or SPI (up to 10
MHz) Host Control Interface
Automatic Prefetching of Critical, User-Specified
Data From the Modules
Broadcast Mode Write to All Ports Simultaneously
Across All FPC402 Controllers
Advanced LED Features for Port Status
Indication, Including Programmable Blinking and
Dimming
Customizable Interrupt Events
Separate Host-Side I/O Voltage: 1.8 V to 3.3 V
Small WQFN Package Enabling Placement on
Bottom Side of PCB Underneath Ports
2 Applications
•
•
•
•
•
Device Information(1)
PART NUMBER
FPC402
PACKAGE
BODY SIZE (NOM)
WQFN (56)
5.00 mm × 11.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Device Comparison
PART
NUMBER
ACCESSIBLE DOWNSTREAM
ADDRESSES
PIN
COMPATIBLE
FPC402
All valid I2C addreses
Yes
FPC401
MSA Addresses: 0xA0, 0xA2
Yes
ToR/Aggregation/Core Switch and Router
Wireless Infrastructure Base Band Unit and
Remote Radio Unit
Video Switch and Router
Storage Cards and Storage Racks
SFP, QSFP, QSFP-DD, OSFP, Mini-SAS HD Port
Management
Simplified Block Diagram
HOST
CONTROLLER
INT
SCL
SDA
FPC402 QUAD PORT CONTROLLER
PORT 0
PORT 1
PORT 2
FPC402 QUAD PORT CONTROLLER
PORT 3
PORT 0
PORT 1
PORT 2
I2C,
STATUS,
CONTROL
PORT 3
I2C,
STATUS,
CONTROL
SFP,
QSFP,
QSFP-DD,
OSFP
SFP,
QSFP,
QSFP-DD,
OSFP
SFP,
QSFP,
QSFP-DD,
OSFP
SFP,
QSFP,
QSFP-DD,
OSFP
SFP,
QSFP,
QSFP-DD,
OSFP
SFP,
QSFP,
QSFP-DD,
OSFP
PORT 0
PORT 1
PORT2
PORT 3
PORT 4
PORT 5
SFP,
QSFP,
QSFP-DD,
OSFP
SFP,
QSFP,
QSFP-DD,
OSFP
PORT 6
PORT 7
Copyright © 2017, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
FPC402
SNLS583A – JUNE 2017 – REVISED OCTOBER 2017
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Description (continued).........................................
Device and Documentation Support....................
1
1
1
2
2
3
6.1 Documentation Support ........................................... 3
6.2
6.3
6.4
6.5
6.6
7
Receiving Notification of Documentation Updates....
Community Resources..............................................
Trademarks ...............................................................
Electrostatic Discharge Caution ................................
Glossary ....................................................................
3
3
3
3
3
Mechanical, Packaging, and Orderable
Information ............................................................. 3
4 Revision History
Changes from Original (June 2017) to Revision A
•
Page
Changed Advance Information to Production Data ............................................................................................................... 1
5 Description (continued)
The FPC402 is compatible with standard SFF-8431, SFF-8436, and SFF-8449 low-speed management
interfaces, including a dedicated 100- or 400-kHz I2C interface to each port. Additional general-purpose pins are
available to perform functions such as driving port status LEDs or controlling power switches. The LED drivers
have convenience features such as programmable blinking and dimming. The interface to the host controller can
operate on a separate supply voltage between 1.8 V and 3.3 V to support low-voltage I/Os.
The FPC402 can prefetch data from user-specified registers in each module, making the data readily accessible
to the host through a fast I2C (up to 1 MHz) or SPI (up to 10 MHz) interface. In addition, the FPC402 can trigger
an interrupt to the host whenever critical, user-configurable events occur associated with any of the ports the
device controls. This eliminates the need to continuously poll the modules.
2
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: FPC402
FPC402
www.ti.com
SNLS583A – JUNE 2017 – REVISED OCTOBER 2017
6 Device and Documentation Support
6.1 Documentation Support
6.1.1 Related Documentation
For related documentation see the following:
• FPC402 Programmer's Guide (SNLU227)
• FPC401 Evaluation Module (EVM) User's Guide (SNLU222)
6.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
6.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
6.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
6.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
6.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
7 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: FPC402
3
PACKAGE OPTION ADDENDUM
www.ti.com
20-Oct-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
FPC402RHUR
ACTIVE
WQFN
RHU
56
2000
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
FPC402
FPC402RHUT
ACTIVE
WQFN
RHU
56
250
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
FPC402
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
20-Oct-2017
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jan-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
FPC402RHUR
WQFN
RHU
56
2000
330.0
24.4
5.3
11.3
1.0
8.0
24.0
Q1
FPC402RHUT
WQFN
RHU
56
250
178.0
24.4
5.3
11.3
1.0
8.0
24.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jan-2018
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
FPC402RHUR
WQFN
RHU
56
2000
367.0
367.0
45.0
FPC402RHUT
WQFN
RHU
56
250
213.0
191.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising