Texas Instruments | TPD1E6B06 Single-Channel ESD Protection Diode in 0201 Package (Rev. E) | Datasheet | Texas Instruments TPD1E6B06 Single-Channel ESD Protection Diode in 0201 Package (Rev. E) Datasheet

Texas Instruments TPD1E6B06 Single-Channel ESD Protection Diode in 0201 Package (Rev. E) Datasheet
Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
TPD1E6B06
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
TPD1E6B06 Single-Channel ESD Protection Diode in 0201 Package
1 Features
3 Description
•
The TPD1E6B06 device is a single-channel TVS
diode for electrostatic discharge (ESD) protection in a
small 0201 package. The TPD1E6B06 is rated to
dissipate ESD strikes above the maximum level
specified in the IEC 61000-4-2 international standard
(Level 4), with ±15-kV contact discharge and ±15-kV
air-gap ESD protection. The device has a back-toback TVS diode configuration for bipolar or
bidirectional signal support. The 6-pF line
capacitance is suitable to provide transient voltage
suppression circuit protection for a wide range of
applications,
supporting
data
rates
up
to
800 Mbps.
1
•
•
•
•
•
•
•
•
IEC 61000-4-2 Level 4 ESD Protection
– ±15-kV Contact Discharge
– ±15-kV Air-Gap Discharge
IEC 61000-4-5 Surge: 3.8 A (8/20 µs)
I/O Capacitance: 6 pF (Typical)
RDYN: 0.55 Ω (Typical)
DC Breakdown Voltage: ±6 V (Minimum)
Low Leakage Current: 10 nA (Typical)
Low ESD Clamping Voltage
Industrial Temperature Range: –40°C to 125°C
Space-Saving 0201 Footprint
(0.6 mm × 0.3 mm × 0.3 mm)
2 Applications
•
•
End Equipment
– Mobile Phones
– Tablets
– Wearables
– Remote Controllers
– Electronic Point of Sale (EPOS)
Interfaces
– Audio Lines
– General-Purpose Input/Output (GPIO)
– Pushbuttons
Typical application interfaces for the TPD1E6B06 are
audio
lines
(microphone,
earphone,
and
speakerphone), SD interfacing, keypad or other
buttons, as well as the VBUS and ID pins of USB
ports. With its industry-standard 0201 package, The
TPD1E6B06 has an extremely small footprint, making
it ideal for space-saving end equipment like mobile
phones, tablets, and wearables.
Device Information(1)
PART NUMBER
TPD1E6B06
PACKAGE
X2SON (2)
BODY SIZE (NOM)
0.60 mm × 0.30 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
IO Line 1
IO Line 2
Connector
(Source of ESD)
1
1
2
2
ESD Sensitive Device
GND Line
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPD1E6B06
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
6.1
6.2
6.3
6.4
6.5
6.6
3
3
4
4
4
5
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 7
7.1 Overview ................................................................... 7
7.2 Functional Block Diagram ......................................... 7
7.3 Feature Description................................................... 7
7.4 Device Functional Modes.......................................... 7
8
Application and Implementation .......................... 8
8.1 Application Information.............................................. 8
8.2 Typical Application ................................................... 8
9 Power Supply Recommendations...................... 10
10 Layout................................................................... 10
10.1 Layout Guidelines ................................................. 10
10.2 Layout Example .................................................... 10
11 Device and Documentation Support ................. 11
11.1
11.2
11.3
11.4
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
11
11
11
11
12 Mechanical, Packaging, and Orderable
Information ........................................................... 11
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (April 2015) to Revision E
Page
•
Added test condition frequency to capacitance ..................................................................................................................... 4
•
Added Community Resources ............................................................................................................................................. 11
Changes from Revision C (February 2013) to Revision D
•
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes section, Application and Implementation section, Power Supply Recommendations section, Layout section,
Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .................. 1
Changes from Revision B (August 2012) to Revision C
•
Page
Page
Updated TOP-SIDE MARKING in the ORDERING INFORMATION table. ........................................................................... 1
Changes from Revision A (April 2012) to Revision B
Page
•
Updated IEC 61000-4-5 (Surge) value in FEATURES........................................................................................................... 1
•
Updated RDYN value in FEATURES........................................................................................................................................ 1
•
Updated Absolute Maximum Ratings. .................................................................................................................................... 3
•
Updated TYPICAL CHARACTERISTICS section................................................................................................................... 4
Changes from Original (February 2012) to Revision A
Page
•
Changed 0402 Package to 0201 Package in title. ................................................................................................................. 1
•
Added RDYN to FEATURES. ................................................................................................................................................... 1
•
Changed supporting data rates from 150Mbps to 800Mbps in the DESCRIPTION section.. ................................................ 1
•
Added ILEAK parameter to the Electrical Characteristics table. ............................................................................................... 4
•
Changed supporting data rates from 150Mbps to 800Mbps in the DESCRIPTION section.. ................................................ 7
2
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
TPD1E6B06
www.ti.com
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
5 Pin Configuration and Functions
DPL Package
2-Pin X2SON
(Top View)
1
2
Pin Functions
PIN
1
2
I/O
DESCRIPTION
I/O
ESD-Protected I/O
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1)
MIN
MAX
UNIT
–5
5
V
3.8
A
VRWM
Maximum voltage allowed from pin 1 to pin 2, or pin 2 to pin 1
IPP
Peak pulse current (tp = 8/20 μs)
PPP
Peak pulse power (tp = 8/20 μs)
50
W
TA
Operating temperature
–40
125
°C
Tstg
Storage temperature
–65
155
°C
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2500
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±1000
IEC 61000-4-2 contact discharge
±15000
IEC 61000-4-2 air-gap discharge
±15000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Pins listed as ±2500
V may actually have higher performance.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Pins listed as ±1000
V may actually have higher performance.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
3
TPD1E6B06
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
www.ti.com
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
Operating free-air temperature, TA
Operating Voltage
Pin 1 to 2 or Pin 2 to 1
NOM
MAX
UNIT
–40
125
°C
–5
5
V
6.4 Thermal Information
TPD1E6B06
THERMAL METRIC (1)
DPL (X2SON)
UNIT
2 PINS
RθJA
Junction-to-ambient thermal resistance
567.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
253.2
°C/W
RθJB
Junction-to-board thermal resistance
31.6
°C/W
ψJT
Junction-to-top characterization parameter
379.1
°C/W
ψJB
Junction-to-board characterization parameter
31.6
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VRWM
Reverse stand-off voltage
ILEAK = 100 nA
ILEAK
Leakage current
Pin 1 = 5 V, Pin 2 = 0 V
VClamp1,2
Clamp voltage with ESD strike on pin 1, pin 2
grounded.
IPP = 1 A, tp = 8/20 μs
10
IPP = 5 A, tp = 8/20 μs
14
VClamp2,1
Clamp voltage with ESD strike on pin 2, pin 1
grounded.
IPP = 1 A, tp = 8/20 μs
10
IPP = 5 A, tp = 8/20 μs
14
RDYN
Dynamic resistance
CIO
I/O capacitance
VIO = 2.5 V; ƒ = 1 MHz
VBR1,2
Breakdown voltage, pin 1 to pin 2
IIO = 1 mA
6
V
VBR2,1
Breakdown voltage, pin 2 to pin 1
IIO = 1 mA
6
V
(1)
4
Pin 1 to Pin 2 (1)
0.55
Pin 2 to Pin 1 (1)
0.55
6
±5
V
100
nA
V
V
Ω
pF
Extraction of RDYN using least squares fit of TLP characteristics between IPP = 10 A and IPP = 20 A.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
TPD1E6B06
www.ti.com
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
6.6 Typical Characteristics
10
80
0
70
-10
60
-20
Amplitude (V)
50
40
30
-30
-40
-50
20
-60
10
-70
0
-80
-10
-15
15
45
75
105
135
Time (ns)
165
195
-90
-15
225
30
30
27
27
24
24
21
21
18
15
12
6
3
3
0
0
16
20
24
Voltage (V)
28
32
36
165
195
40
0
4
8
12
16
20
24
Voltage (V)
D001
Figure 3. Clamping Voltage VTLP = F(ITLP), PIN1 to PIN2
D001
28
32
36
40
D001
Figure 4. Clamping Voltage VTLP = F(ITLP), PIN2 to PIN1
6
1
90
I
P
0.8
5
0.6
Current (A)
0.4
Current (mA)
225
12
6
12
105
135
Time (ns)
15
9
8
75
18
9
4
45
Figure 2. ESD Clamp Voltage –8-kV Contact ESD
Current (A)
Current (A)
Figure 1. ESD Clamp Voltage +8-kV Contact ESD
0
15
D001
0.2
0
-0.2
-0.4
-0.6
75
4
60
3
45
2
30
1
15
Power (W)
Amplitude (V)
90
-0.8
-1
-12 -10 -8
0
-6
-4
-2
0 2 4
Voltage (V)
6
8
10 12 14 16
0
5
D001
Figure 5. IV Curve
10
15
20
25
30
Time (Ps)
35
40
45
0
50
D001
Figure 6. Surge Graph, Pin 1 to Pin 2
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
5
TPD1E6B06
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
6
I
P
5
90
3
75
-3
0
-6
60
45
2
30
1
15
Loss (dB)
3
-9
Power (W)
Current (A)
4
-12
-15
-18
-21
-24
-27
-30
9
9
10
2x
10
0x
1x
6
6
10
D001
10
-33
0
45
x1
40
10
35
6
25
30
Time (Ps)
10
20
1x
15
3
10
0x
5
10
0
0
50
10
0
D001
Frequency (Hz)
Figure 7. Surge Graph, Pin 2 to Pin 1
Figure 8. Insertion Loss, Pin 1 to Pin 2
3
0
-3
-6
Loss (dB)
-9
-12
-15
-18
-21
-24
-27
-30
9
9
0
2x
1
10
1x
6
0
x1
6
10
x1
0
10
0
6
1x
10
0
x1
0
3
10
-33
D001
Frequency (Hz)
Figure 9. Insertion Loss, Pin 2 to Pin 1
6
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
TPD1E6B06
www.ti.com
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
7 Detailed Description
7.1 Overview
The TPD1E6B06 is a single-channel TVS diode for ESD protection in a small 0201 package. The TPD1E6B06 is
rated to dissipate ESD strikes above the maximum level specified in the IEC 61000-4-2 international standard
(Level 4), with ±15-kV contact discharge and ±15-kV air-gap ESD protection. The device has a back-to-back TVS
diode configuration for bipolar or bidirectional signal support. The 6-pF line capacitance is suitable to provide
transient voltage suppression circuit protection for a wide range of applications, supporting data rates up to
800 Mbps. Typical application interfaces for the TPD1E6B06 are audio lines (microphone, earphone, and
speakerphone), SD interfacing, keypad or other buttons, as well as the VBUS and ID pins of USB ports.
7.2 Functional Block Diagram
1
2
7.3 Feature Description
The TPD1E6B06 is a single-channel TVS diode for ESD protection. This device provides circuit protection from
ESD strikes up to ±15-kV contact and ±15-kV air-gap as specified in the IEC 61000-4-2 international standard.
The device can also handle up to 3.8 A of surge current (IEC61000-4-5 8/20 μs). The TPD1E6B06 has 6 pF
(typical) of capacitance which allows this device to support data rates up to 800 Mbps. Additionally, this low
capacitance can even be necessary for an audio signal (for example, if a Class D amplifier is used). The
TPD1E6B06 also has a small dynamic resistance of 0.55Ω (typical). This makes the clamping voltage low when
it is protecting other circuits, which is crucial for protecting ICs during ESD events. The breakdown is bidirectional
so that this protection device is a good fit for GPIO and especially audio lines which carry bidirectional signals.
Low leakage current allows the diode to conserve power when working below the VRWM. The industrial
temperature range of –40°C to 125°C makes this ESD device to work well at extensive temperatures in most
environments. The space-saving 0201 package is designed for small electronic devices like mobile phones and
wearables.
7.4 Device Functional Modes
The TPD1E6B06 is a passive clamp that has low leakage during normal operation and activates whenever the
voltage between pin 1 and pin 2 goes above VRWM or below -VRWM. During IEC ESD events, transient voltages
as high as ±15 kV can be clamped between the two pins. When the voltages on the protected lines fall below the
trigger voltage, the device reverts back to the low leakage passive state.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
7
TPD1E6B06
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
When a system contains a human interface connector, it becomes vulnerable to large system-level ESD strikes
that standard ICs cannot survive. TVS ESD protection diodes are typically used to suppress ESD at these
connectors. TPD1E6B06 is a single-channel ESD protection device containing back-to-back TVS diodes, which
is typically used to provide a path to ground for dissipating ESD events on bidirectional signal lines between a
human interface connector and a system. As the current from an ESD event passes through the TVS diode, only
a small voltage drop is present across the diode structure. This is the voltage presented to the protected IC. The
low RDYN of the triggered TVS holds this voltage, VCLAMP, to a tolerable level to the protected IC.
8.2 Typical Application
L Audio IN
Audio Amplifier
Class AB
(ESD Sensitive)
L Audio
L
GND
R Audio IN
Speaker
Connector
(Source of ESD)
1
Audio Amplifier
Class AB
(ESD Sensitive)
1
R Audio
R
GND
2
GND
2
Figure 10. Audio Application Schematic
8.2.1 Design Requirements
For this design example, two TPD1E6B06s will be used to protect left and right audio channels. For this audio
application, the following system parameters are known.
Table 1. Design Parameters
DESIGN PARAMETER
VALUE
Audio amplifier class
AB
Audio signal voltage range
–3 V to 3 V
Audio frequency content
20 Hz to 20 kHz
Required IEC 61000-4-2 ESD protection
±8 kV Contact and ±15kV Air-Gap
8.2.2 Detailed Design Procedure
To begin the design process, some parameters must be decided upon; the designer should make sure:
• Voltage range on the protected line must not exceed the reverse standoff voltage of the TVS diode(s) (VRWM).
• Operating frequency is supported by the I/O capacitance CIO of the TVS diode.
8
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
TPD1E6B06
www.ti.com
•
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
IEC 61000-4-2 protection requirement is covered by the IEC performance of the TVS diode.
For this application, the audio signal voltage range is –3 V to 3 V. The VRWM for our TVS is –5 V to 5 V;
therefore, our bidirectional TVS will not break down during normal operation, and therefore normal operation of
our audio signal will not be effected due to the signal voltage range. Note that in this application, a bidirectional
TVS like TPD1E6B06 is required.
Next, consider the frequency content of this audio signal. In this application with the class AB amplifier, the
frequency content is from 20 Hz to 20 kHz; ensure that the TVS I/O capacitance will not distort this signal by
filtering it. With TPD1E6B06 typical capacitance of 6 pF, which leads to a typical 3-dB bandwidth of 700 MHz,
this diode has sufficient bandwidth to pass the audio signal without distorting it.
Finally, the human interface in this application requires standard Level 4 IEC 61000-4-2 system-level ESD
protection (±8-kV Contact/ ±15-kV Air-Gap). TPD1E6B06 can survive ±15-kV Contact/ ±15-kV Air-Gap, which
indicates that our device can provide sufficient protection for the interface. For any TVS diode to provide its full
range of ESD protection capabilities, as well as to minimize the noise and EMI disturbances the board will
undergo during ESD events, it is crucial that a system designer uses proper board layout of their TVS ESD
protection diodes. For instructions on properly laying out TPD1E6B06, see Layout.
8.2.3 Application Curves
Figure 11 and Figure 12 are captures of the voltage clamping waveforms of TPD1E6B06 during a +8-kV Contact
IEC 61000-4-2 ESD strike and a -8-kV Contact IEC 61000-4-2 ESD strike, respectively, in a typical application
with proper board layout.
10
80
0
70
-10
60
-20
Amplitude (V)
Amplitude (V)
90
50
40
30
-30
-40
-50
20
-60
10
-70
0
-80
-10
-15
15
45
75
105
135
Time (ns)
165
195
225
-90
-15
15
45
75
105
135
Time (ns)
165
195
D001
Figure 11. IEC 61000-4-2 ESD Clamp Voltage +8-kV
Contact ESD
225
D001
Figure 12. IEC 61000-4-2 ESD Clamp Voltage -8-kV Contact
ESD
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
9
TPD1E6B06
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
www.ti.com
9 Power Supply Recommendations
This device is a passive TVS diode-based ESD protection device so there is no need to power it. Take care to
make sure that the maximum voltage specifications for each pin are not violated.
10 Layout
10.1 Layout Guidelines
•
The optimum placement is as close to the connector as possible.
– EMI during an ESD event can couple from the trace being struck to other nearby unprotected traces,
resulting in early system failures.
– The PCB designer must minimize the possibility of EMI coupling by keeping any unprotected traces away
from the protected traces which are between the TVS and the connector.
Route the protected traces as straight as possible.
Eliminate any sharp corners on the protected traces between the TVS and the connector by using rounded
corners with the largest radii possible.
– Electric fields tend to build up on corners, increasing EMI coupling.
If pin 1 or pin 2 is connected to ground, use a thick and short trace for this return path
•
•
•
10.2 Layout Example
To connector
To protected IC
Place pin 1 on the signal line
Minimum
distance
from
connector
(source of
ESD)
Thick and short return path to GND
Figure 13. Layout Recommendation
10
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
TPD1E6B06
www.ti.com
SLLSEB2E – FEBRUARY 2012 – REVISED OCTOBER 2015
11 Device and Documentation Support
11.1 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.2 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: TPD1E6B06
11
PACKAGE OPTION ADDENDUM
www.ti.com
12-Oct-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TPD1E6B06DPLR
ACTIVE
X2SON
DPL
2
15000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
H
TPD1E6B06DPLT
ACTIVE
X2SON
DPL
2
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
H
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
12-Oct-2015
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Jan-2020
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPD1E6B06DPLR
X2SON
DPL
2
15000
178.0
8.4
0.36
0.66
0.33
2.0
8.0
Q3
TPD1E6B06DPLT
X2SON
DPL
2
250
178.0
8.4
0.36
0.66
0.33
2.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Jan-2020
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPD1E6B06DPLR
X2SON
DPL
2
15000
205.0
200.0
33.0
TPD1E6B06DPLT
X2SON
DPL
2
250
205.0
200.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising