Texas Instruments | DS26LS31MQML Quad High Speed Differential Line Driver (Rev. B) | Datasheet | Texas Instruments DS26LS31MQML Quad High Speed Differential Line Driver (Rev. B) Datasheet

Texas Instruments DS26LS31MQML Quad High Speed Differential Line Driver (Rev. B) Datasheet
DS26LS31MQML
www.ti.com
SNOSAM5B – AUGUST 2005 – REVISED APRIL 2013
DS26LS31MQML Quad High Speed Differential Line Driver
Check for Samples: DS26LS31MQML
FEATURES
DESCRIPTION
•
•
•
The DS26LS31MQML is a quad differential line driver
designed for digital data transmission over balanced
lines. The DS26LS31MQML meets all the
requirements of EIA Standard RS-422 and Federal
Standard 1020. It is designed to provide unipolar
differential drive to twisted-pair or parallel-wire
transmission lines.
1
2
•
•
•
•
•
Operation from Single 5V Supply
Outputs Won't Load Line When VCC = 0V
Four Line Drivers in One Package for
Maximum Package Density
Output Short-Circuit Protection
Complementary Outputs
Meets the Requirements of EIA Standard RS422
Pin Compatible with AM26LS31
Glitch Free Power Up/Down
The circuit provides an enable and disable function
common to all four drivers. The DS26LS31MQML
features TRI-STATE outputs and logically ANDed
complementary outputs. The inputs are all LS
compatible and are all one unit load.
The DS26LS31 features a power up/down protection
circuit which keeps the output in a high impedance
state (TRI-STATE) during power up or down
preventing erroneous glitches on the transmission
lines.
Logic and Connection Diagrams
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2013, Texas Instruments Incorporated
DS26LS31MQML
SNOSAM5B – AUGUST 2005 – REVISED APRIL 2013
www.ti.com
Top View
Figure 1. CDIP Package
See Package Numbers NAJ0020A, NFE0016A, NAD0016A
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1)
Supply Voltage
7V
Input Voltage
7V
Output Voltage
5.5V
−0.25 to 6V
Output Voltage (Power OFF)
Maximum Power Dissipation at 25°C (2)
NFE0016A Package
1400 mW
NAJ0020A Package
1600 mW
NAD0016A Package
850 mW
Junction Temperature (TJ)
+150°C
Thermal Resistance, Junction-to-Ambient
θJA
NFE0016A Package
94°C/W derate above +25°C at 10.6 mW/°C
NAJ0020A Package
83°C/W derate above +25°C at 12 mW/°C
NAD0016A Package
163°C/W derate above +25°C at 6.1 mW/°C
Thermal Resistance, Junction-to-Case
θJC
NFE0016A Package
16°C/W
NAJ0020A Package
19°C/W
NAD0016A Package
14°C/W
ESD Tolerance
(1)
(2)
2500V
“Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be specified. They are not meant to imply
that the devices should be operated at these limits. The tables of “Electrical Characteristics” provide conditions for actual device
operation.
Derate CDIP = 11.5 mW/°C, LCCC = 13mW/°C, CLGA = 7.4mW/°C above 25°C.
Recommended Operating Conditions
Supply Voltage, VCC
4.5 V to 5.5 V
−55°C to +125°C
Temperature, TA
2
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: DS26LS31MQML
DS26LS31MQML
www.ti.com
SNOSAM5B – AUGUST 2005 – REVISED APRIL 2013
Radiation Features
DS26LS31MEFQML
300 Krads (Si)
DS26LS31MJFQML
300 Krads (Si)
DS26LS31MJFQMLV
300 Krads (Si)
DS26LS31MWFQML
300 Krads (Si)
DS26LS31MWFQMLV
300 Krads (Si)
Quality Conformance Inspection
MIL-STD-883, Method 5005 - Group A
Subgroup
Description
Temp (°C)
1
Static tests at
+25
2
Static tests at
+125
3
Static tests at
-55
4
Dynamic tests at
+25
5
Dynamic tests at
+125
6
Dynamic tests at
-55
7
Functional tests at
+25
8A
Functional tests at
+125
8B
Functional tests at
-55
9
Switching tests at
+25
10
Switching tests at
+125
11
Switching tests at
-55
DS26LS31M - SMD, QMLV & RH Electrical Characteristics DC Parameters
The following conditions apply, unless otherwise specified. +V = 5V, VCM = 0V. (1)
Parameter
Test Conditions
VIH
Logical "1" Input Voltage
VCC = 4.5V
VIL
Logical "0" Input Voltage
VCC = 5.5V
Notes
Min
See and (2)
(3)
2
See (2) and
.8
(3)
(3)
VOH
Logical "1" Output Voltage
VCC = 4.5V, IOH = -20mA
See
VOL
Logical "0" Output Voltage
VCC = 4.5V, IOL = 20mA
See (3)
(3)
Max
2.5
Unit
Subgroups
V
1, 2, 3
V
1, 2, 3
V
1, 2, 3
.5
V
1, 2, 3
IIH
Logical "1" Input Current
VCC = 5.5V, VIN= 2.7V
See
-2.0
20
uA
1, 2, 3
IIL
Logical "0" Input Current
VCC = 5.5V, VIN = .4V
See (3)
100
-360
uA
1, 2, 3
II
Input Reverse Current
VCC = 5.5V, VIN = 7V
See (3)
-.01
.1
mA
1, 2, 3
VCC = 5.5V, VO = .5V
See
(3)
-20
uA
1, 2, 3
VCC = 5.5V, VO = 2.5V
See (3)
20
uA
1, 2, 3
-1.5
V
1, 2, 3
-150
mA
1, 2, 3
80
mA
1, 2, 3
IO
TRI-STATE Output Current
VIC
Input Clamp Voltage
VCC = 4.5V, IIN = -18mA
See (3)
IOS
Output Short Circuit Current
VCC = 5.5V
See (3)
ICC
Power Supply Current
VCC = 5.5V, All Outputs Disabled or
Active
See (3)
(1)
(2)
(3)
-30
Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate
sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters
are ensured only for the conditions as specified in MIL-STD 883, Method 1019, Condition A.
Parameter tested go-no-go only.
Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: DS26LS31MQML
3
DS26LS31MQML
SNOSAM5B – AUGUST 2005 – REVISED APRIL 2013
www.ti.com
DS26LS31M - SMD, QMLV and RH Electrical Characteristics AC Parameters - Propagation Delay
Time
The following conditions apply, unless otherwise specified. VCC = 5V, VIN = 1.3V to VO = 1.3V, V (pulse) = 0 to 3V. (1)
Parameter
Test Conditions
Notes
tPLH
Input to Output
CL = 30 pF
See (2)
tPHL
Input to Output
CL = 30 pF
See (2)
tSkew
Output to Output
CL = 30 pF
See (2)
S2 Open, Enable, CL = 10 pF
See (2)
tPLZ
tPHZ
tPZL
tPZH
(1)
(2)
Min
Enable to Output
S2 Open, Enable, CL = 10 pF
See (2)
S1 Open, Enable, CL = 10 pF
See (2)
S1 Open, Enable, CL = 10 pF
See (2)
S2 Open, Enable, CL = 30 pF
See (2)
S2 Open, Enable, CL = 30 pF
See (2)
Enable to Output
Enable to Output
S1 Open, Enable, CL = 30 pF
See (2)
S1 Open, Enable, CL = 30 pF
See (2)
Enable to Output
Subgroups
Max
Unit
20
ns
9
30
ns
10, 11
20
ns
9
30
ns
10, 11
6
ns
9
9
ns
10, 11
35
ns
9
53
ns
10, 11
35
ns
9
53
ns
10, 11
30
ns
9
45
ns
10, 11
30
ns
9
45
ns
10, 11
45
ns
9
68
ns
10, 11
45
ns
9
68
ns
10, 11
40
ns
9
60
ns
10, 11
40
ns
9
60
ns
10, 11
Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate
sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters
are ensured only for the conditions as specified in MIL-STD 883, Method 1019, Condition A.
Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures.
DS26LS31M - SMD, QMLV and RH Electrical Characteristics DC Parameters - Drift Values
The following conditions apply, unless otherwise specified. Delta calculations performed on QMLV only devices after burn-in
and at Group B5.
Parameter
Test Conditions
Notes
Min
Max
Unit
Subgroups
VOL
Output Low Voltage
VCC = 4.5, IOL = 20 mA
See (1)
-50
50
mV
1
VOH
Output High Voltage
VCC = 4.5, IOH = -20 mA
See (1)
-250
250
mV
1
Power Supply Current
VCC = 5.5, All outputs disabled or
active
See (1)
-8
8
mA
1
Max
Unit
Subgroups
V
1, 2, 3
V
1, 2, 3
V
1, 2, 3
ICC
(1)
Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures.
DS26LS31M - 883 Electrical Characteristics DC Parameters
Parameter
VIH
Logical "1" Input Voltage
VIL
Logical "0" Input Voltage
VOH
Logical "1" Output Voltage
(1)
(2)
4
Test Conditions
Notes
See (1) and
(2)
Min
2
See (1) and
.8
(2)
VCC = 4.5V, IOH = -20mA
See (2)
2.5
Parameter tested go-no-go only.
Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: DS26LS31MQML
DS26LS31MQML
www.ti.com
SNOSAM5B – AUGUST 2005 – REVISED APRIL 2013
DS26LS31M - 883 Electrical Characteristics DC Parameters (continued)
Parameter
Test Conditions
Notes
Min
Max
Unit
Subgroups
VOL
Logical "0" Output Voltage
VCC = 4.5V, IOL = 20mA
See (2)
.5
V
1, 2, 3
IIH
Logical "1" Input Current
VCC = 5.5V, VIN = 2.7V
See (2)
20
uA
1, 2, 3
(2)
IIL
Logical "0" Input Current
VCC = 5.5V, VIN = .4V
See
-200
uA
1, 2, 3
II
Input Reverse Current
VCC = 5.5V, VIN = 7V
See (2)
.1
mA
1, 2, 3
VCC = 5.5V, VO = .5V
See (2)
-20
uA
1, 2, 3
20
uA
1, 2, 3
-1.5
V
1, 2, 3
mA
1, 2, 3
IO
TRI-STATE Output Current
VCC = 5.5V, VO = 2.5V
See
VIC
Input Clamp Voltage
VCC = 4.5V, IIN = -18mA
See (2)
IOS (min)
Output Short Circuit Current
VCC = 5.5V
See (2)
Output Short Circuit Current
VCC = 5.5V
See
(2)
-150
mA
1, 2, 3
Power Supply Current
VCC = 5.5V, All Outputs Disabled or
Active
See
(2)
60
mA
1, 2, 3
IOS (max)
ICC
(2)
-30
DS26LS31M - 883 Electrical Characteristics AC Parameters - Propagation Delay Time
The following conditions apply, unless otherwise specified. VCC = 5V, CL = 50pF or equivalent impedance provided by diode
load.
Parameter
tPLH
Input to Output
tPHL
Input to Output
tSkew
Output to Output
Test Conditions
(2)
See (1) and
(2)
See (1) and
(2)
Enable to Output
S2 Open, /Enable
S1 Open, Enable
tPHZ
Enable to Output
S1 Open, /Enable
S2 Open, Enable
tPZL
Enable to Output
S2 Open, /Enable
S1 Open, Enable
tPZH
Enable to Output
S1 Open, /Enable
(1)
(2)
Min
See (1) and
S2 Open, Enable
tPLZ
Notes
See (1) and
(2)
See (1) and
(2)
See (1) and
(2)
See (1) and
(2)
See (1) and
(2)
See (1) and
(2)
See (1) and
(2)
See (1) and
(2)
Subgroups
Max
Unit
15
ns
9
30
ns
10, 11.
15
ns
9
30
ns
10, 11.
6
ns
9
9
ns
10, 11.
35
ns
9
53
ns
10, 11.
35
ns
9
53
ns
10, 11.
25
ns
9
45
ns
10, 11.
25
ns
9
45
ns
10, 11.
30
ns
9
68
ns
10, 11.
30
ns
9
68
ns
10, 11.
30
ns
9
60
ns
10, 11.
30
ns
9
60
ns
10, 11.
Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures.
Subgroup 10 and 11 specified but not tested.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: DS26LS31MQML
5
DS26LS31MQML
SNOSAM5B – AUGUST 2005 – REVISED APRIL 2013
www.ti.com
AC TEST CIRCUIT AND SWITCHING TIME WAVEFORMS
S1 and S2 of load circuit are closed except where shown.
Figure 2. AC Test Circuit
f = 1 MHz, tr ≤ 15 ns, tf ≤ 6 ns
Figure 3. Propagation Delays
f = 1 MHz, tr ≤ 15 ns, tf ≤ 6 ns
Figure 4. Enable and Disable Times
TYPICAL APPLICATIONS
Figure 5. Two-Wire Balanced System, RS-422
RT is optional although highly recommended to reduce reflection.
6
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: DS26LS31MQML
DS26LS31MQML
www.ti.com
SNOSAM5B – AUGUST 2005 – REVISED APRIL 2013
Typical Performance Characteristics
DS26LS31MQMLCN Unloaded IC
vs
Frequency
vs
TA
DS26LS31MQML ICC
vs
VCC vs TA
Figure 6.
Figure 7.
DS26LS31MQMLCN VOH
vs
IOH vs TA
DS26LS31MQMLCN VOL
vs
IOL vs TA
Figure 8.
Figure 9.
DS26LS31MQMLCN VOD
vs
IO vs TA
Figure 10.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: DS26LS31MQML
7
DS26LS31MQML
SNOSAM5B – AUGUST 2005 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Date
Released
Revision
8/04/05
A
3/01/06
4/15/2013
8
Section
New Release, Corporate format
Ordering Info. Table, Absolute Ratings,
Maximum Operating Conditions, New
Radiation Section. Typos in QMLV &
RH, 883 AC Electrical Characteristics
Parameters Column
Originator
Changes
R. Malone
2 MDS data sheets converted into a Corp. data
sheet format. Following MDS data sheets will
be Archived MDDS26LS31M-X-RH, Rev.2A0,
MNDS26LS31M-X, Rev. 0A0
A1
R. Malone
Added: Juction temp., Thermal Resistance θJA
and θJC. Added a Radiation Section. Changed:
Maximum Operating Conditions to
Recommended Operating Conditions, Enable
and Disable Time to Enable to Output. Revision
A will be archived.
B
TIS
Changed layout of National Data Sheet to TI
format
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: DS26LS31MQML
PACKAGE OPTION ADDENDUM
www.ti.com
2-Oct-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
AM26LS31MW/883
ACTIVE
CFP
NAD
16
19
TBD
Call TI
Call TI
-55 to 125
DS26LS31MW
/883 Q ACO
/883 Q >T
DS26LS31ME-SMD
ACTIVE
LCCC
NAJ
20
50
TBD
Call TI
Call TI
-55 to 125
DS26LS31ME
-SMD Q
5962-78023
01Q2A ACO
01Q2A >T
DS26LS31MJ-SMD
ACTIVE
CDIP
NFE
16
25
TBD
Call TI
Call TI
-55 to 125
DS26LS31MJ-SMD
5962-7802301MEA Q
DS26LS31MJ/883
ACTIVE
CDIP
NFE
16
25
TBD
Call TI
Call TI
-55 to 125
DS26LS31MJ/883 Q
DS26LS31MW/883
ACTIVE
CFP
NAD
16
19
TBD
Call TI
Call TI
-55 to 125
DS26LS31MW
/883 Q ACO
/883 Q >T
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
2-Oct-2017
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF DS26LS31MQML, DS26LS31MQML-SP :
• Military: DS26LS31MQML
• Space: DS26LS31MQML-SP
NOTE: Qualified Version Definitions:
• Military - QML certified for Military and Defense Applications
• Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
Addendum-Page 2
MECHANICAL DATA
NAJ0020A
E20A (Rev F)
www.ti.com
MECHANICAL DATA
NFE0016A
J0016A
J16A (REV L)
www.ti.com
MECHANICAL DATA
NAD0016A
W16A (Rev T)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising