Texas Instruments | Single 3-Input Positive OR-AND Gate | Datasheet | Texas Instruments Single 3-Input Positive OR-AND Gate Datasheet

Texas Instruments Single 3-Input Positive OR-AND Gate Datasheet
SN74LVC1G3208-Q1
www.ti.com
SCES822 – DECEMBER 2010
SINGLE 3-INPUT POSITIVE OR-AND GATE
Check for Samples: SN74LVC1G3208-Q1
FEATURES
1
•
•
•
•
•
•
•
Qualified for Automotive Applications
Supports 5-V VCC Operation
Inputs Accept Voltages to 5.5 V
Max tpd of 5 ns at 3.3 V
Low Power Consumption, 10-mA Max ICC
±24-mA Output Drive at 3.3 V
Input Hysteresis Allows Slow Input Transition
and Better Switching Noise Immunity at the
Input
(Vhys = 250 mV Typ at 3.3 V)
Can Be Used in Three Combinations:
– OR-AND Gate
– OR Gate
– AND Gate
Ioff Supports Partial-Power-Down Mode
Operation
•
•
DESCRIPTION/ORDERING INFORMATION
This device is designed for 1.65-V to 5.5-V VCC
operation.
The SN74LVC1G3208-Q1 is a single 3-input positive
OR-AND gate. It performs the Boolean function Y =
(A + B) ⋅ C in positive logic.
By tying one input to GND or VCC, the
SN74LVC1G3208-Q1 offers two more functions.
When C is tied to VCC, this device performs as a
2-input OR gate (Y = A + B). When A is tied to GND,
the device works as a 2-input AND gate (Y = B ⋅ C).
This device also works as a 2-input AND gate when
B is tied to GND (Y = A ⋅ C).
This device is fully specified for partial-power-down
applications using Ioff. The Ioff circuitry disables the
outputs, preventing damaging current backflow
through the device when it is powered down.
ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C SOT (SC-70) – DCK
(1)
ORDERABLE PART NUMBER
Reel of 3000
CLVC1G3208IDCKRQ1
TOP-SIDE MARKING
DGR
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
FUNCTION TABLE (1)
INPUTS
B
C
OUTPUT
Y
H
X
H
H
X
H
H
H
X
X
L
L
L
L
H
L
A
(1)
X = Valid H or L
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
SN74LVC1G3208-Q1
SCES822 – DECEMBER 2010
www.ti.com
LOGIC DIAGRAM (POSITIVE LOGIC)
A
B
1
3
4
C
Y
6
FUNCTION SELECTION TABLE
LOGIC FUNCTION
FIGURE
2-Input AND Gate
Figure 1
2-Input OR Gate
Figure 2
Y = (A + B) ⋅ C
Figure 3
LOGIC CONFIGURATIONS
VCC
B
VCC
A
Y
C
B
1
6
2
5
3
4
C
Y
A
C
Y
1
6
2
5
3
4
C
Y
Figure 1. 2-Input AND Gate
VCC
A
Y
B
A
B
1
6
2
5
3
4
Y
Figure 2. 2-Input OR Gate
VCC
A
B
A
Y
C
B
1
6
2
5
3
4
C
Y
Figure 3. Y = (A + B) ⋅ C
2
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74LVC1G3208-Q1
SN74LVC1G3208-Q1
www.ti.com
SCES822 – DECEMBER 2010
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VCC
MIN
MAX
Supply voltage range
–0.5
6.5
UNIT
V
(2)
VI
Input voltage range
–0.5
6.5
V
VO
Voltage range applied to any output in the high-impedance or power-off state (2)
–0.5
6.5
V
VO
Voltage range applied to any output in the high or low state (2)
–0.5
VCC + 0.5
IIK
Input clamp current
VI < 0
–50
mA
IOK
Output clamp current
VO < 0
–50
mA
IO
Continuous output current
±50
mA
±100
mA
259
°C/W
150
°C
(3)
Continuous current through VCC or GND
qJA
Package thermal impedance
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
(4)
DCK package
–65
V
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
The value of VCC is provided in the recommended operating conditions table.
The package thermal impedance is calculated in accordance with JESD 51-7.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74LVC1G3208-Q1
3
SN74LVC1G3208-Q1
SCES822 – DECEMBER 2010
www.ti.com
RECOMMENDED OPERATING CONDITIONS (1)
VCC
Supply voltage
Operating
Data retention only
VCC = 1.65 V to 1.95 V
VIH
High-level input voltage
VCC = 2.3 V to 2.7 V
VCC = 3 V to 3.6 V
VCC = 4.5 V to 5.5 V
MIN
MAX
1.65
5.5
1.5
UNIT
V
0.65 × VCC
1.7
V
2
0.7 × VCC
VCC = 1.65 V to 1.95 V
0.35 × VCC
VCC = 2.3 V to 2.7 V
0.7
VCC = 3 V to 3.6 V
0.8
VIL
Low-level input voltage
VI
Input voltage
0
5.5
V
VO
Output voltage
0
VCC
V
VCC = 4.5 V to 5.5 V
0.3 × VCC
VCC = 1.65 V
–4
VCC = 2.3 V
IOH
High-level output current
V
–8
VCC = 3 V
–16
mA
–24
VCC = 4.5 V
IOL
Low-level output current
–32
VCC = 1.65 V
4
VCC = 2.3 V
8
VCC = 3 V
16
mA
24
Δt/Δv
Input transition rise or fall rate
VCC = 4.5 V
32
VCC = 1.8 V ± 0.15 V, 2.5 V ± 0.2 V
20
VCC = 3.3 V ± 0.3 V
10
VCC = 5 V ± 0.5 V
TA
(1)
4
Operating free-air temperature
ns/V
5
–40
85
°C
All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74LVC1G3208-Q1
SN74LVC1G3208-Q1
www.ti.com
SCES822 – DECEMBER 2010
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IOH = –100 mA
VOH
1.65 V to 5.5 V
1.65 V
1.2
IOH = –8 mA
2.3 V
1.9
4.5 V
1.65 V to 5.5 V
0.1
IOL = 4 mA
1.65 V
0.45
IOL = 8 mA
2.3 V
0.3
VI = 5.5 V or GND
VI or VO = 5.5 V
ICC
VI = 5.5 V or GND
IO = 0
ΔICC
One input at VCC – 0.6 V,
Other inputs at VCC or GND
Ci
VI = VCC or GND
V
0.4
0.55
4.5 V
Ioff
(1)
3.8
3V
IOL = 32 mA
II
2.3
IOL = 100 mA
IOL = 24 mA
A, B, or
C inputs
V
IOH = –32 mA
IOL = 16 mA
UNIT
2.4
3V
IOH = –24 mA
MAX
VCC – 0.1
IOH = –4 mA
IOH = –16 mA
VOL
MIN TYP (1)
VCC
0.55
0 to 5.5 V
±5
mA
0
±10
mA
1.65 V to 5.5 V
10
mA
3 V to 5.5 V
500
mA
3.3 V
3.5
pF
All typical values are at VCC = 3.3 V, TA = 25°C.
Switching Characteristics
over recommended operating free-air temperature range, CL = 30 pF or 50 pF (unless otherwise noted) (see Figure 4)
FROM
(INPUT)
TO
(OUTPUT)
A, B, or C
Y
PARAMETER
tpd
VCC = 1.8 V
± 0.15 V
VCC = 2.5 V
± 0.2 V
VCC = 3.3 V
± 0.3 V
VCC = 5 V
± 0.5 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
2.5
17.5
1.8
7.6
1.8
5.9
1.3
4.2
UNIT
ns
Operating Characteristics
TA = 25°C
PARAMETER
Cpd
Power dissipation capacitance
TEST
CONDITIONS
VCC = 1.8 V
VCC = 2.5 V
VCC = 3.3 V
VCC = 5 V
TYP
TYP
TYP
TYP
f = 10 MHz
15
15
16
17
UNIT
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74LVC1G3208-Q1
pF
5
SN74LVC1G3208-Q1
SCES822 – DECEMBER 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION
VLOAD
S1
RL
From Output
Under Test
CL
(see Note A)
Open
GND
RL
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
VLOAD
GND
LOAD CIRCUIT
INPUTS
VCC
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
5 V ± 0.5 V
VI
tr/tf
VCC
VCC
3V
VCC
≤2 ns
≤2 ns
≤2.5 ns
≤2.5 ns
VM
VLOAD
CL
RL
V∆
VCC/2
VCC/2
1.5 V
VCC/2
2 × VCC
2 × VCC
6V
2 × VCC
30 pF
30 pF
50 pF
50 pF
1 kΩ
500 Ω
500 Ω
500 Ω
0.15 V
0.15 V
0.3 V
0.3 V
VI
Timing Input
VM
0V
tw
tsu
VI
Input
VM
VM
th
VI
Data Input
VM
VM
0V
0V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VOLTAGE WAVEFORMS
PULSE DURATION
VI
VM
Input
VM
0V
VOH
VM
Output
VM
VOL
VM
0V
VLOAD/2
VM
tPZH
VOH
Output
VM
tPLZ
Output
Waveform 1
S1 at VLOAD
(see Note B)
tPLH
tPHL
VM
tPZL
tPHL
tPLH
VI
Output
Control
VM
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
VOL + V∆
VOL
tPHZ
Output
Waveform 2
S1 at GND
(see Note B)
VM
VOH − V∆
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
Figure 4. Load Circuit and Voltage Waveforms
6
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74LVC1G3208-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2019
PACKAGING INFORMATION
Orderable Device
Status
(1)
CLVC1G3208IDCKRQ1
ACTIVE
Package Type Package Pins Package
Drawing
Qty
SC70
DCK
6
3000
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Op Temp (°C)
Device Marking
(4/5)
-40 to 85
DGR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SN74LVC1G3208-Q1 :
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2019
• Catalog: SN74LVC1G3208
• Enhanced Product: SN74LVC1G3208-EP
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
25-Sep-2019
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
CLVC1G3208IDCKRQ1
Package Package Pins
Type Drawing
SC70
DCK
6
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
3000
180.0
8.4
Pack Materials-Page 1
2.47
B0
(mm)
K0
(mm)
P1
(mm)
2.3
1.25
4.0
W
Pin1
(mm) Quadrant
8.0
Q3
PACKAGE MATERIALS INFORMATION
www.ti.com
25-Sep-2019
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
CLVC1G3208IDCKRQ1
SC70
DCK
6
3000
202.0
201.0
28.0
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising