Texas Instruments | Low Power, 1.8/2.5/3.3-V Input, 3.3-V CMOS Output, Single Inverter Gate | Datasheet | Texas Instruments Low Power, 1.8/2.5/3.3-V Input, 3.3-V CMOS Output, Single Inverter Gate Datasheet

Texas Instruments Low Power, 1.8/2.5/3.3-V Input, 3.3-V CMOS Output, Single Inverter Gate Datasheet
SN74AUP1T04
www.ti.com
SCES800 – APRIL 2010
LOW POWER, 1.8/2.5/3.3-V INPUT, 3.3-V CMOS OUTPUT, SINGLE
INVERTER GATE
Check for Samples: SN74AUP1T04
FEATURES
1
•
•
•
•
•
•
•
•
Single-Supply Voltage Translator
Output Level Up to Supply VCC CMOS Level
– 1.8 V to 3.3 V (at VCC = 3.3 V)
– 2.5 V to 3.3 V (at VCC = 3.3 V)
– 1.8 V to 2.5 V (at VCC = 2.5 V)
– 3.3 V to 2.5 V (at VCC = 2.5 V
Schmitt-Trigger Inputs Reject Input Noise and
Provide Better Output Signal Integrity
Ioff Supports Partial Power Down (VCC = 0 V)
Very Low Static Power Consumption:
0.1 µA
Very Low Dynamic Power Consumption:
0.9 µA
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
Pb-Free Packages Available: SC-70 (DCK)
2 x 2.1 x 0.65 mm (Height 1.1 mm)
•
•
More Gate Options Available at
www.ti.com/littlelogic
ESD Performance Tested Per JESD 22
– 2000-V Human-Body Model
(A114-B, Class II)
– 1000-V Charged-Device Model (C101)
DCK PACKAGE
(TOP VIEW)
NC
1
A
2
GND
3
5
VCC
4
Y
DESCRIPTION/ORDERING INFORMATION
The SN74AUP1T04 performs the Boolean function Y = A with designation for logic-level translation applications
with output referenced to supply VCC.
AUP technology is the industry's lowest-power logic technology designed for use in extending battery-life in
operating. All input levels that accept 1.8-V LVCMOS signals, while operating from either a single 3.3-V or 2.5-V
VCC supply. This product also maintains excellent signal integrity (see Figure 1 and Figure 2).
The wide VCC range of 2.3 V to 3.6 V allows the possibility of switching output level to connect to external
controllers or processors.
Schmitt-trigger inputs (ΔVT = 210 mV between positive and negative input transitions) offer improved noise
immunity during switching transitions, which is especially useful on analog mixed-mode designs. Schmitt-trigger
inputs reject input noise, ensure integrity of output signals, and allow for slow input signal transition.
Ioff is a feature that allows for powered-down conditions (VCC = 0 V) and is important in portable and mobile
applications. When VCC = 0 V, signals in the range from 0 V to 3.6 V can be applied to the inputs and outputs of
the device. No damage occurs to the device under these conditions.
The SN74AUP1T04 is designed with optimized current-drive capability of 4 mA to reduce line reflections,
overshoot, and undershoot caused by high-drive outputs.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
SN74AUP1T04
SCES800 – APRIL 2010
www.ti.com
ORDERING INFORMATION (1)
PACKAGE (2)
TA
–40°C to 85°C
(1)
(2)
(3)
SOT (SC-70) – DCK
TOP-SIDE MARKING (3)
ORDERABLE PART NUMBER
Reel of 3000
SN74AUP1T04DCKR
Reel of 250
SN74AUP1T04DCKT
6C_
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
The actual top-side marking has one additional character that designates the wafer fab/assembly site.
FUNCTION TABLE
INPUT
(Lower Level Input)
OUTPUT
(VCC CMOS)
A
Y
H
L
L
H
Supply VCC = 2.3 V to 2.7 V (2.5 V)
INPUTS
VT+ max = VIH min
VT- min = VIL max
A
OUTPUT
CMOS
B
Y
VIH = 1.1 V
VOH = 1.85 V
VIL = 0.35 V
VOL = 0.45 V
Supply VCC = 3 V to 3.6 V (3.3 V)
INPUTS
VT+ max = VIH min
VT- min = VIL max
A
OUTPUT
CMOS
B
Y
VIH = 1.19 V
VOH = 2.55 V
VIL = 0.5 V
VOL = 0.45 V
LOGIC DIAGRAM (INVERTER GATE)
A
Static-Power Consumption
(µA)
2
Y
Dynamic-Power Consumption
(pF)
3
80%
2.5
60%
3.3-V
LVC
Logic†
40%
Voltage − V
100%
80%
3.3-V
40%
Logic†
20%
20%
AUP
0%
†
0%
AUP
Single, dual, and triple gates
Switching Characteristics
at 25 MHz†
3.5
100%
60%
2
1.5
1
Input
Output
0.5
0
−0.5
0
5
10
15
20 25 30
Time − ns
35
40
45
† AUP1G08 data at C = 15 pF
L
Figure 1. AUP – The Lowest-Power Family
2
4
Figure 2. Excellent Signal Integrity
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP1T04
SN74AUP1T04
www.ti.com
SCES800 – APRIL 2010
3.3 V
3.3 V
VIH = 1.19 V
VIL = 0.5 V
VIH = 1.19 V
VIL = 0.5 V
1.8-V
System
2.5-V
System
3.3-V
System
3.3-V
System
2.5 V
2.5 V
VIH = 1.10 V
VIL = 0.35 V
VIH = 1.10 V
VIL = 0.35 V
1.8-V
System
3.3-V
System
2.5-V
System
2.5-V
System
Figure 3. Typical Design Examples
3.3 V
1.8-V
System
3.3-V
System
VOH min
VT+ max = VIH min = 1.19 V
VT− min = V IL max = 0.5 V
VOL max
Input Switching Waveform
Output Switching Waveform
Figure 4. Switching Thresholds for 1.8-V to 3.3-V Translation
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP1T04
3
SN74AUP1T04
SCES800 – APRIL 2010
www.ti.com
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range
–0.5
4.6
V
VI
Input voltage range (2)
–0.5
4.6
V
VO
Voltage range applied to any output in the high-impedance or power-off state (2)
–0.5
4.6
V
–0.5
VCC + 0.5
(2)
UNIT
VO
Output voltage range in the high or low state
IIK
Input clamp current
VI < 0
–50
mA
IOK
Output clamp current
VO < 0
–50
mA
IO
Continuous output current
±20
mA
Continuous current through VCC or GND
±50
mA
259
°C/W
150
°C
qJA
Package thermal impedance (3)
Tstg
Storage temperature range
(1)
(2)
(3)
DCK package
–65
V
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS (1)
VCC
Supply voltage
VI
Input voltage
VO
Output voltage
IOH
High-level output current
IOL
Low-level output current
TA
Operating free-air temperature
(1)
4
MIN
MAX
2.3
3.6
V
0
3.6
V
VCC
V
0
VCC = 2.3 V
–3.1
VCC = 3 V
–4
VCC = 2.3 V
3.1
VCC = 3 V
4
–40
85
UNIT
mA
mA
°C
All unused inputs of the device must be held at VCC or GND to ensure proper device operation. See the TI application report Implications
of Slow or Floating CMOS Inputs, literature number SCBA004.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP1T04
SN74AUP1T04
www.ti.com
SCES800 – APRIL 2010
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA = –40°C
to 85°C
TA = 25°C
VCC
MIN
TYP
UNIT
MAX
MIN
MAX
VT+
Positive-going input
threshold voltage
2.3 V to 2.7 V
0.6
1.1
0.6
1.1
3 V to 3.6 V
0.75
1.16
0.75
1.19
VT–
Negative-going
input threshold
voltage
2.3 V to 2.7 V
0.35
0.6
0.35
0.6
3 V to 3.6 V
0.5
0.85
0.5
0.85
ΔVT
Hysteresis
(VT+ – VT–)
2.3 V to 2.7 V
0.23
0.6
0.1
0.6
3 V to 3.6 V
0.25
0.56
0.15
0.56
IOH = –20 mA
2.3 V to 3.6 V
IOH = –2.3 mA
VOH
2.3 V
IOH = –3.1 mA
IOH = –2.7 mA
3V
IOH = –4 mA
IOL = 20 mA
1.9
1.85
2.72
2.67
2.6
2.55
3V
IOL = 4 mA
All inputs
1.97
2.3 V
IOL = 3.1 mA
IOL = 2.7 mA
II
VCC – 0.1
2.05
2.3 V to 3.6 V
IOL = 2.3 mA
VOL
VCC – 0.1
VI = 3.6 V or GND
V
V
V
V
0.1
0.1
0.31
0.33
0.44
0.45
0.31
0.33
V
0.44
0.45
0 V to 3.6 V
0.1
0.5
mA
0V
0.1
0.5
mA
Ioff
VI or VO = 0 V to 3.6 V
ΔIoff
VI or VO = 3.6 V
0 V to 0.2 V
0.2
0.5
mA
ICC
VI = 3.6 V or GND, IO = 0
2.3 V to 3.6 V
0.5
0.9
mA
One input at 0.3 V or 1.1 V,
Other inputs at 0 or VCC, IO = 0
2.3 V to 2.7 V
4
One input at 0.45 V or 1.2 V,
Other inputs at 0 or VCC, IO = 0
3 V to 3.6 V
12
ΔICC
mA
Ci
VI = VCC or GND
3.3 V
1.5
pF
Co
VO = VCC or GND
3.3 V
3
pF
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V, VI = 1.8 V ± 0.15 V (unless otherwise noted)
(see Figure 5)
PARAMETER
tpd
FROM
(INPUT)
A
TO
(OUTPUT)
Y
CL
TA = –40°C
to 85°C
TA = 25°C
MIN
TYP
MAX
MIN
MAX
5 pF
1.8
2.3
2.9
0.5
6.8
10 pF
2.3
2.8
3.4
1
7.9
15 pF
2.6
3.1
3.8
1
8.7
30 pF
3.8
4.4
5.1
1.5
10.8
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP1T04
UNIT
ns
5
SN74AUP1T04
SCES800 – APRIL 2010
www.ti.com
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V, VI = 2.5 V ± 0.2 V (unless otherwise noted)
(see Figure 5)
PARAMETER
tpd
FROM
(INPUT)
A
TO
(OUTPUT)
Y
CL
TA = –40°C
to 85°C
TA = 25°C
MIN
TYP
MAX
MIN
UNIT
MAX
5 pF
1.8
2.3
3.1
0.5
6
10 pF
2.2
2.8
3.5
1
7.1
15 pF
2.6
3.2
5.2
1
7.9
30 pF
3.7
4.4
5.2
1.5
10
ns
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V, VI = 3.3 V ± 0.3 V (unless otherwise noted)
(see Figure 5)
PARAMETER
tpd
FROM
(INPUT)
A
TO
(OUTPUT)
Y
CL
TA = –40°C
to 85°C
TA = 25°C
UNIT
MIN
TYP
MAX
MIN
MAX
5 pF
2
2.7
3.5
0.5
5.5
10 pF
2.4
3.1
3.9
1
6.5
15 pF
2.8
3.5
4.3
1
7.4
30 pF
4
4.7
5.5
1.5
9.5
ns
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V, VI = 1.8 V ± 0.15 V (unless otherwise noted)
(see Figure 5)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
CL
A
Y
UNIT
MIN
TYP
MAX
MIN
MAX
1.6
2
2.5
0.5
8
10 pF
2
2.4
2.9
1
8.5
15 pF
2.3
2.8
3.3
1
9.1
30 pF
3.4
3.9
4.4
1.5
9.8
5 pF
tpd
TA = –40°C
to 85°C
TA = 25°C
ns
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V, VI = 2.5 V ± 0.2 V (unless otherwise noted)
(see Figure 5)
PARAMETER
tpd
6
FROM
(INPUT)
A
TO
(OUTPUT)
Y
CL
TA = –40°C
to 85°C
TA = 25°C
MIN
TYP
MAX
MIN
MAX
5 pF
1.6
1.9
2.4
0.5
5.3
10 pF
2
2.3
2.7
1
6.1
15 pF
2.3
2.7
3.1
1
6.8
30 pF
3.4
3.8
4.2
1.5
8.5
Submit Documentation Feedback
UNIT
ns
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP1T04
SN74AUP1T04
www.ti.com
SCES800 – APRIL 2010
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V, VI = 3.3 V ± 0.3 V (unless otherwise noted)
(see Figure 5)
PARAMETER
tpd
FROM
(INPUT)
A
TO
(OUTPUT)
Y
CL
TA = –40°C
to 85°C
TA = 25°C
MIN
TYP
MAX
MIN
MAX
5 pF
1.6
2.1
2.7
0.5
4.7
10 pF
2
2.4
3
1
5.7
15 pF
2.3
2.7
3.3
1
6.2
30 pF
3.4
3.8
4.4
1.5
7.8
UNIT
ns
OPERATING CHARACTERISTICS
TA = 25°C
PARAMETER
Cpd
Power dissipation capacitance
TEST CONDITIONS
f = 10 MHz
VCC = 2.5 V
VCC = 3.3 V
TYP
TYP
4
5
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP1T04
UNIT
pF
7
SN74AUP1T04
SCES800 – APRIL 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION
From Output
Under Test
CL
(see Note A)
VCC = 2.5 V
± 0.2 V
VCC = 3.3 V
± 0.3 V
5, 10, 15, 30 pF
VI/2
VCC/2
5, 10, 15, 30 pF
VI/2
VCC/2
1 MΩ
CL
VMI
VMO
LOAD CIRCUIT
VI
VMI
Input
VMI
0V
tPHL
tPLH
VOH
VMO
Output
VMo
VOL
tPHL
tPLH
VOH
Output
VMo
VMo
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
NOTES: A.
B.
C.
D.
CL includes probe and jig capacitance.
All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, slew rate ≥ 1 V/ns.
The outputs are measured one at a time, with one transition per measurement.
tPLH and tPHL are the same as tpd.
Figure 5. Load Circuit and Voltage Waveforms
8
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP1T04
PACKAGE OPTION ADDENDUM
www.ti.com
26-Apr-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
SN74AUP1T04DCKR
ACTIVE
SC70
DCK
Pins Package Eco Plan (2)
Qty
5
3000 Green (RoHS &
no Sb/Br)
Lead/Ball Finish
CU NIPDAU
MSL Peak Temp (3)
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Nov-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
SN74AUP1T04DCKR
Package Package Pins
Type Drawing
SC70
DCK
5
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
3000
178.0
9.0
Pack Materials-Page 1
2.4
B0
(mm)
K0
(mm)
P1
(mm)
2.5
1.2
4.0
W
Pin1
(mm) Quadrant
8.0
Q3
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Nov-2010
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN74AUP1T04DCKR
SC70
DCK
5
3000
180.0
180.0
18.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising