Texas Instruments | SN74AUP2G126 Low-Power Dual Bus Buffer Gate With 3-State Outputs (Rev. D) | Datasheet | Texas Instruments SN74AUP2G126 Low-Power Dual Bus Buffer Gate With 3-State Outputs (Rev. D) Datasheet

Texas Instruments SN74AUP2G126 Low-Power Dual Bus Buffer Gate With 3-State Outputs (Rev. D) Datasheet
SN74AUP2G126
www.ti.com
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
LOW-POWER DUAL BUS BUFFER GATE WITH 3-STATE OUTPUTS
Check for Samples: SN74AUP2G126
FEATURES
1
•
•
•
•
•
•
•
•
Available in the Texas Instruments NanoStar™
Package
Low Static-Power Consumption
(ICC = 0.9 μA Max)
Low Dynamic-Power Consumption
(Cpd = 4 pF Typ at 3.3 V)
Low Input Capacitance (Ci = 1.5 pF Typ)
Low Noise – Overshoot and Undershoot
<10% of VCC
Input-Disable Feature Allows Floating Input
Conditions
Ioff Supports Partial-Power-Down Mode
Operation
Input Hysteresis Allows Slow Input Transition
and Better Switching Noise Immunity at Input
DCU PACKAGE
(TOP VIEW)
1OE
1A
2Y
GND
1
2
8
7
3
6
4
5
•
•
•
•
•
•
•
RSE PACKAGE
(TOP VIEW)
DQE PACKAGE
(TOP VIEW)
VCC
2OE
1Y
2A
1OE
1A
2Y
GND
1
8
2
7
3
6
4
5
VCC
2OE
1Y
2A
Wide Operating VCC Range of 0.8 V to 3.6 V
Optimized for 3.3-V Operation
3.6-V I/O Tolerant to Support Mixed-Mode
Signal Operation
tpd = 9.9 ns Max at 3.3 V
Suitable for Point-to-Point Applications
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Performance Tested Per JESD 22
– 2000-V Human-Body Model
(A114-B, Class II)
– 1000-V Charged-Device Model (C101)
YFP OR YZP PACKAGE
(TOP VIEW)
VCC
2OE
1
1Y
2
2A
3
8
4
7
1OE
6
1A
5
2Y
1OE
1A
2Y
GND
A1
1 8
A2
B1
2 7
B2
C1
3 6
C2
D1
45
D2
VCC
2OE
1Y
2A
GND
The exposed center pad, if used, must be connected
only as a secondary GND or left electrically open.
See mechanical drawings for dimensions.
DESCRIPTION/ORDERING INFORMATION
The AUP family is TI's premier solution to the industry's low-power needs in battery-powered portable
applications. This family ensures a very low static and dynamic power consumption across the entire VCC range
of 0.8 V to 3.6 V, resulting in an increased battery life. This product also maintains excellent signal integrity (see
Figure 1 and Figure 2).
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2009, Texas Instruments Incorporated
SN74AUP2G126
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
Static-Power Consumption
( mA)
www.ti.com
Switching Characteristics
Dynamic-Power Consumption
at 25 MHz†
(pF)
100%
100%
80%
80%
3.5
60%
60%
3.3-V
3.3-V
LVC
†
Logic
40%
40%
Voltage - V
3
†
Logic
2.5
Input
2
Output
1.5
1
0.5
20%
20%
AUP
0%
†
0
AUP
0%
-0.5
Single, dual, and triple gates
0
†
Figure 1. AUP – The Lowest Power Family
5
10
15
20
25
Time - ns
30
35
40
45
AUP1G08 data at CL = 15 pF
Figure 2. Excellent Signal Integrity
The SN74AUP2G126 is a dual bus driver/line driver with 3-state outputs, designed for 0.8-V to 3.6-V VCC
operation. The outputs are disabled when the associated output-enable (OE) input is low. This device has the
input-disable feature, which allows floating input signals.
To ensure the high-impedance state during power up or power down, OE should be tied to GND through a
pulldown resistor; the minimum value of the resistor is determined by the current-sourcing capability of the driver.
NanoStar™ package technology is a major breakthrough in IC packaging concepts, using the die as the
package.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
ORDERING INFORMATION (1)
–40°C to 85°C
(1)
(2)
(3)
ORDERABLE
PART NUMBER
PACKAGE (2)
TA
TOP-SIDE
MARKING (3)
NanoStar™ – WCSP (DSBGA)
0.23-mm Large Bump – YFP (Pb-free)
Reel of 3000
SN74AUP2G126YFPR
_ _ _ HN_
NanoStar™ – WCSP (DSBGA)
0.23-mm Large Bump – YZP (Pb-free)
Reel of 3000
SN74AUP2G126YZPR
_ _ _ HN_
uQFN – DQE
Reel of 5000
SN74AUP2G126DQER
PW
QFN – RSE
Reel of 5000
SN74AUP2G126RSER
HN
VSSOP – DCU
Reel of 3000
SN74AUP2G126DCUR
H26_
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
YFP/YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following
character to designate the wafer fab/assembly site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, • = Pb-free).
DCU: The actual top-side marking has one additional character to designate the wafer fab/assembly site.
FUNCTION TABLE
INPUTS
(1)
2
OE
A
OUTPUT
Y
H
H
H
H
L
L
L
X (1)
Z
Floating inputs allowed
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
SN74AUP2G126
www.ti.com
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
LOGIC DIAGRAMS (POSITIVE LOGIC)
DCU, DQE, YFP, and YZP Packages
1
1OE
2
6
1A
1Y
7
2OE
5
3
2A
2Y
RSE Package
7
1OE
6
2
1A
1Y
1
2OE
3
5
2A
2Y
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range
–0.5
4.6
V
VI
Input voltage range (2)
–0.5
4.6
V
VO
Voltage range applied to any output in the high-impedance or power-off state (2)
–0.5
4.6
V
(2)
UNIT
VO
Output voltage range in the high or low state
IIK
Input clamp current
VI < 0
–50
mA
IOK
Output clamp current
VO < 0
–50
mA
IO
Continuous output current
±20
mA
Continuous current through VCC or GND
±50
mA
θJA
Tstg
(1)
(2)
(3)
Package thermal impedance (3)
–0.5 VCC + 0.5
DCU package
227
DQE package
261
RSE package
253
YZP package
102
YFP package
98.8
Storage temperature range
–65
V
°C/W
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
The package thermal impedance is calculated in accordance with JESD 51-7.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
3
SN74AUP2G126
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
www.ti.com
RECOMMENDED OPERATING CONDITIONS (1)
VCC
Supply voltage
VCC = 0.8 V
VIH
High-level input voltage
VCC = 1.1 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3 V to 3.6 V
MIN
MAX
0.8
3.6
VCC
3.6
0.65 × VCC
3.6
1.6
3.6
2
3.6
VCC = 0.8 V
VIL
Low-level input voltage
VO
Output voltage
IOH
High-level output current
IOL
Low-level output current
Input transition rise or fall rate
TA
Operating free-air temperature
(1)
4
V
V
0
VCC = 1.1 V to 1.95 V
0 0.35 × VCC
VCC = 2.3 V to 2.7 V
0
VCC = 3 V to 3.6 V
0
0.9
Active state
0
VCC
3-state
0
3.6
0.7
VCC = 0.8 V
–20
VCC = 1.1 V
–1.1
VCC = 1.4 V
–1.7
VCC = 1.65 V
–1.9
VCC = 2.3 V
–3.1
VCC = 3 V
–4
VCC = 0.8 V
20
VCC = 1.1 V
1.1
VCC = 1.4 V
1.7
VCC = 1.65 V
1.9
VCC = 2.3 V
3.1
VCC = 3 V
Δt/Δv
UNIT
V
V
μA
mA
μA
mA
4
VCC = 0.8 V to 3.6 V
200
ns/V
85
°C
–40
All unused inputs of the device must be held at VCC or GND to ensure proper device operation. See the TI application report
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
SN74AUP2G126
www.ti.com
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
VOH
TEST CONDITIONS
VCC
MIN
0.8 V to 3.6 V
VCC – 0.1
VCC – 0.1
1.1 V
0.75 × VCC
0.7 × VCC
IOH = –1.7 mA
1.4 V
1.11
1.03
IOH = –1.9 mA
1.65 V
1.32
1.3
2.05
1.97
2.3 V
IOH = –2.7 mA
3V
IOH = –4 mA
IOL = 20 μA
1.9
1.85
2.72
2.67
2.6
2.55
0.8 V to 3.6 V
MAX
UNIT
V
0.1
0.1
0.3 ×
VCC
IOL = 1.1 mA
1.1 V
0.3 ×
VCC
IOL = 1.7 mA
1.4 V
0.31
0.37
IOL = 1.9 mA
1.65 V
0.31
0.35
0.31
0.33
0.44
0.45
0.31
0.33
0.44
0.45
0 V to 3.6 V
0.1
0.5
μA
IOL = 2.3 mA
2.3 V
IOL = 3.1 mA
IOL = 2.7 mA
3V
IOL = 4 mA
II
TA = –40°C to 85°C
MAX
IOH = –1.1 mA
IOH = –3.1 mA
A or OE
input
TYP
IOH = –20 μA
IOH = –2.3 mA
VOL
TA = 25°C
MIN
VI = GND to 3.6 V
V
Ioff
VI or VO = 0 V to 3.6 V
0V
0.2
0.6
μA
ΔIoff
VI or VO = 0 V to 3.6 V
0 V to 0.2 V
0.2
0.9
μA
IOZ
VO = VCC or GND
3.6 V
0.1
0.5
μA
ICC
VI = GND or (VCC to 3.6 V),
OE = VCC , IO = 0
0.8 V to 3.6 V
0.5
0.9
μA
A input
ΔICC
OE input
All inputs
VI = VCC – 0.6 V (1), IO = 0
VI = GND to 3.6 V,
OE = GND (2)
CI
VI = VCC or GND
Co
VO = VCC or GND
(1)
(2)
3.3 V
0.8 V to 3.6 V
0V
2
3.6 V
2
3.6 V
3
40
50
110
120
0
0
μA
pF
pF
One input at VCC – 0.6 V, other input at VCC or GND
To show ICC is very low when the input-disable feature is enabled
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
5
SN74AUP2G126
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
www.ti.com
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, CL = 5 pF (unless otherwise noted) (see Figure 3 and Figure 4)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
VCC
TA = 25°C
MIN
0.8 V
tpd
A
Y
OE
Y
OE
Y
MIN
MAX
UNIT
19.2
0.5
7.5
17.9
0.5
18.7
1.5 V ± 0.1 V
0.6
5.2
10.8
0.5
12.4
1.8 V ± 0.15 V
0.8
4.1
8.1
0.5
9.7
2.5 V ± 0.2 V
1.1
2.9
5
0.5
6.5
3.3 V ± 0.3 V
0.5
3
9.5
0.5
9.9
ns
19.6
1.2 V ± 0.1 V
0.5
8.4
20.8
0.5
21.8
1.5 V ± 0.1 V
0.5
5.6
11.8
0.5
13.7
1.8 V ± 0.15 V
0.7
4.3
8.8
0.5
10.6
2.5 V ± 0.2 V
0.9
2.9
5.4
0.5
7
3.3 V ± 0.3 V
0.5
2.8
8.8
0.5
9.3
0.8 V
tdis
TA = –40°C to 85°C
MAX
1.2 V ± 0.1 V
0.8 V
ten
TYP
ns
12.1
1.2 V ± 0.1 V
0.6
5.2
10.9
0.5
11.1
1.5 V ± 0.1 V
1.1
3.8
7
0.9
7.1
1.8 V ± 0.15 V
1.9
3.5
5.6
1.6
5.8
2.5 V ± 0.2 V
0.9
2.5
3.9
0.8
4.2
3.3 V ± 0.3 V
0.5
3.5
9.3
0.5
9.3
ns
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, CL = 10 pF (unless otherwise noted) (see Figure 3 and Figure 4)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
VCC
TA = 25°C
MIN
TYP
1.2 V ± 0.1 V
0.5
0.8 V
tpd
A
Y
OE
Y
6
OE
Y
MIN
MAX
8.7
20.6
0.5
21.3
1.5 V ± 0.1 V
1.2
6
12.2
0.5
13.7
1.8 V ± 0.15 V
1.4
4.8
9.2
0.5
10.8
2.5 V ± 0.2 V
1.5
3.4
5.8
0.5
7.2
3.3 V ± 0.3 V
0.5
3.4
8.9
0.5
9.4
UNIT
ns
21.9
1.2 V ± 0.1 V
0.5
9.7
23.1
0.5
24
1.5 V ± 0.1 V
1
6.4
13.2
0.5
15
1.8 V ± 0.15 V
1
5
9.9
0.5
11.7
2.5 V ± 0.2 V
1.2
3.4
10.4
0.5
12
3.3 V ± 0.3 V
0.5
3.2
8.1
0.5
8.7
0.8 V
tdis
MAX
23
0.8 V
ten
TA = –40°C to 85°C
ns
13.4
1.2 V ± 0.1 V
0.8
6.2
12.6
0.6
12.7
1.5 V ± 0.1 V
2.1
4.6
7.9
1.9
8.1
1.8 V ± 0.15 V
1.7
4.7
8.2
1.5
8.3
2.5 V ± 0.2 V
1
3.3
5.1
0.9
5.3
3.3 V ± 0.3 V
1.2
4.5
7.8
1.1
7.9
Submit Documentation Feedback
ns
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
SN74AUP2G126
www.ti.com
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, CL = 15 pF (unless otherwise noted) (see Figure 3 and Figure 4)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
VCC
TA = 25°C
MIN
0.8 V
tpd
A
Y
OE
Y
OE
Y
MIN
MAX
23.4
UNIT
26.2
0.5
9.7
22.7
0.5
1.5 V ± 0.1 V
1.7
4.6
13.6
0.5
15
1.8 V ± 0.15 V
1.7
5.4
10.2
0.5
11.7
2.5 V ± 0.2 V
1.7
3.9
6.5
0.5
7.9
3.3 V ± 0.3 V
0.5
3.7
8.4
0.5
8.9
25.6
ns
23
1.2 V ± 0.1 V
0.5
10.5
24.8
0.5
1.5 V ± 0.1 V
1.5
7.1
14.3
0.5
16
1.8 V ± 0.15 V
1.4
5.6
10.8
0.5
12.4
2.5 V ± 0.2 V
1.6
3.9
6.8
0.5
8.3
3.3 V ± 0.3 V
0.5
3.6
7.6
0.5
8.3
0.8 V
tdis
TA = –40°C to 85°C
MAX
1.2 V ± 0.1 V
0.8 V
ten
TYP
ns
13.6
1.2 V ± 0.1 V
1.1
6.5
12.7
1
12.8
1.5 V ± 0.1 V
0.5
4.8
9.1
0.5
9.2
1.8 V ± 0.15 V
1.8
5.4
9.2
1.7
9.3
2.5 V ± 0.2 V
1.6
3.7
5.5
1.5
5.7
3.3 V ± 0.3 V
2.8
5.3
7.9
2.7
7.9
ns
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, CL = 30 pF (unless otherwise noted) (see Figure 3 and Figure 4)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
VCC
TA = 25°C
MIN
0.8 V
tpd
A
Y
OE
Y
0.5
13
OE
Y
MIN
MAX
30.8
0.5
31.2
1.5 V ± 0.1 V
2.7
9.1
18
1.1
19.1
1.8 V ± 0.15 V
2.6
7.2
13.6
1
14.8
2.5 V ± 0.2 V
2.6
5.3
8.6
1.3
9.9
3.3 V ± 0.3 V
1.4
4.8
7.9
0.7
8.6
UNIT
ns
32.8
1.2 V ± 0.1 V
0.5
14.4
32.4
0.5
33.1
1.5 V ± 0.1 V
2.5
9.7
18.5
1.1
19.9
1.8 V ± 0.15 V
2.3
7.6
14.3
0.8
15.7
2.5 V ± 0.2 V
2.4
5.3
9
1.2
10.3
3.3 V ± 0.3 V
2.8
4.6
7.2
1.7
8.2
0.8 V
tdis
MAX
36.4
1.2 V ± 0.1 V
0.8 V
ten
TYP
TA = –40°C to 85°C
ns
20.1
1.2 V ± 0.1 V
0.5
10.3
19.3
0.5
19.3
1.5 V ± 0.1 V
1.9
7.6
14.5
1.8
14.5
1.8 V ± 0.15 V
3
8.8
14.9
2.8
14.9
2.5 V ± 0.2 V
2.9
6.5
10
2.9
10.1
3.3 V ± 0.3 V
0.5
8.2
17.9
0.5
17.9
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
ns
7
SN74AUP2G126
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
www.ti.com
OPERATING CHARACTERISTICS
TA = 25°C
PARAMETER
TEST CONDITIONS
Outputs enabled
Cpd
Power dissipation
capacitance
Outputs disabled
8
f = 10 MHz
f = 10 MHz
Submit Documentation Feedback
VCC
TYP
0.8 V
3.8
1.2 V ± 0.1 V
3.7
1.5 V ± 0.1 V
3.7
1.8 V ± 0.15 V
3.7
2.5 V ± 0.2 V
3.9
3.3 V ± 0.3 V
4
0.8 V
0
1.2 V ± 0.1 V
0
1.5 V ± 0.1 V
0
1.8 V ± 0.15 V
0
2.5 V ± 0.2 V
0
3.3 V ± 0.3 V
0
UNIT
pF
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
SN74AUP2G126
www.ti.com
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
PARAMETER MEASUREMENT INFORMATION
(Propagation Delays, Setup and Hold Times, and Pulse Width)
From Output
Under Test
CL
(see Note A)
1 MW
LOAD CIRCUIT
CL
VM
VI
VCC = 0.8 V
VCC = 1.2 V
± 0.1 V
VCC = 1.5 V
± 0.1 V
VCC = 1.8 V
± 0.15 V
VCC = 2.5 V
± 0.2 V
VCC = 3.3 V
± 0.3 V
5, 10, 15, 30 pF
VCC/2
VCC
5, 10, 15, 30 pF
VCC/2
VCC
5, 10, 15, 30 pF
VCC/2
VCC
5, 10, 15, 30 pF
VCC/2
VCC
5, 10, 15, 30 pF
VCC/2
VCC
5, 10, 15, 30 pF
VCC/2
VCC
tw
VCC
Input
VCC/2
VCC/2
VI
VM
Input
0V
VM
VOLTAGE WAVEFORMS
PULSE DURATION
0V
tPHL
tPLH
VOH
VM
Output
VM
VOL
tPHL
VCC
Timing Input
VCC/2
0V
tPLH
tsu
VOH
Output
VM
VCC
VM
VOL
Data Input
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
NOTES: A.
B.
C.
D.
E.
th
VCC/2
VCC/2
0V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
CL includes probe and jig capacitance.
All input pulses are supplied by generators having the following characteristics: PRR £ 10 MHz, ZO = 50 W, tr/tf = 3 ns.
The outputs are measured one at a time, with one transition per measurement.
tPLH and tPHL are the same as tpd.
All parameters and waveforms are not applicable to all devices.
Figure 3. Load Circuit and Voltage Waveforms
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
9
SN74AUP2G126
SCES687D – JANUARY 2007 – REVISED DECEMBER 2009
www.ti.com
PARAMETER MEASUREMENT INFORMATION
(Enable and Disable Times)
2 ´ VCC
S1
5 kW
From Output
Under Test
GND
CL
(see Note A)
5 kW
TEST
S1
tPLZ/tPZL
tPHZ/tPZH
2 ´ VCC
GND
LOAD CIRCUIT
CL
VM
VI
VD
VCC = 0.8 V
VCC = 1.2 V
± 0.1 V
VCC = 1.5 V
± 0.1 V
VCC = 1.8 V
± 0.15 V
VCC = 2.5 V
± 0.2 V
VCC = 3.3 V
± 0.3 V
5, 10, 15, 30 pF
VCC/2
VCC
0.1 V
5, 10, 15, 30 pF
VCC/2
VCC
0.1 V
5, 10, 15, 30 pF
VCC/2
VCC
0.1 V
5, 10, 15, 30 pF
VCC/2
VCC
0.15 V
5, 10, 15, 30 pF
VCC/2
VCC
0.15 V
5, 10, 15, 30 pF
VCC/2
VCC
0.3 V
VCC
Output
Control
Output
Waveform 1
S1 at 2 ´ VCC
(see Note B)
VCC/2
0V
tPZL
tPLZ
VCC
VCC/2
tPZH
Output
Waveform 2
S1 at GND
(see Note B)
VCC/2
VOL + VD
VOL
tPHZ
VCC/2
VOH
VOH - VD
»0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR £ 10 MHz, ZO = 50 W, tr/tf = 3 ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. All parameters and waveforms are not applicable to all devices.
Figure 4. Load Circuit and Voltage Waveforms
10
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): SN74AUP2G126
PACKAGE OPTION ADDENDUM
www.ti.com
24-Mar-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
SN74AUP2G126DCUR
ACTIVE
VSSOP
DCU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
H26R
SN74AUP2G126DQER
ACTIVE
X2SON
DQE
8
5000
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
PW
SN74AUP2G126RSER
ACTIVE
UQFN
RSE
8
5000
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
PW
SN74AUP2G126YFPR
ACTIVE
DSBGA
YFP
8
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
HNN
SN74AUP2G126YZPR
ACTIVE
DSBGA
YZP
8
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
HNN
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
24-Mar-2017
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Aug-2017
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SN74AUP2G126DCUR
VSSOP
DCU
8
3000
180.0
8.4
2.25
3.35
1.05
4.0
8.0
Q3
SN74AUP2G126DQER
X2SON
DQE
8
5000
180.0
8.4
1.2
1.6
0.55
4.0
8.0
Q1
SN74AUP2G126RSER
UQFN
RSE
8
5000
180.0
8.4
1.7
1.7
0.7
4.0
8.0
Q2
SN74AUP2G126YFPR
DSBGA
YFP
8
3000
178.0
9.2
0.9
1.75
0.6
4.0
8.0
Q1
SN74AUP2G126YZPR
DSBGA
YZP
8
3000
178.0
9.2
1.02
2.02
0.63
4.0
8.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Aug-2017
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN74AUP2G126DCUR
SN74AUP2G126DQER
VSSOP
DCU
8
3000
202.0
201.0
28.0
X2SON
DQE
8
5000
202.0
201.0
28.0
SN74AUP2G126RSER
UQFN
RSE
8
5000
202.0
201.0
28.0
SN74AUP2G126YFPR
DSBGA
YFP
8
3000
220.0
220.0
35.0
SN74AUP2G126YZPR
DSBGA
YZP
8
3000
220.0
220.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
YFP0008
DSBGA - 0.5 mm max height
SCALE 10.000
DIE SIZE BALL GRID ARRAY
B
E
A
BALL A1
CORNER
D
0.30
0.25
C
0.5 MAX
SEATING PLANE
0.19
0.13
0.05 C
SYMM
D
C
SYMM
1.2
TYP
D: Max = 1.59 mm, Min = 1.53 mm
B
E: Max = 0.79 mm, Min = 0.73 mm
0.4 TYP
A
8X
0.015
0.25
0.21
C A B
1
2
0.4 TYP
4225242/A 08/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
YFP0008
DSBGA - 0.5 mm max height
DIE SIZE BALL GRID ARRAY
(0.4) TYP
8X ( 0.23)
1
2
A
(0.4) TYP
B
SYMM
C
D
SYMM
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 50X
0.05 MAX
0.05 MIN
METAL UNDER
SOLDER MASK
( 0.23)
METAL
SOLDER MASK
OPENING
EXPOSED
METAL
( 0.23)
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
DEFINED
NON-SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
NOT TO SCALE
4225242/A 08/2019
NOTES: (continued)
3. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
See Texas Instruments Literature No. SNVA009 (www.ti.com/lit/snva009).
www.ti.com
EXAMPLE STENCIL DESIGN
YFP0008
DSBGA - 0.5 mm max height
DIE SIZE BALL GRID ARRAY
(0.4) TYP
(R0.05) TYP
8X ( 0.25)
1
2
A
(0.4) TYP
B
SYMM
METAL
TYP
C
D
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
SCALE: 50X
4225242/A 08/2019
NOTES: (continued)
4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.
www.ti.com
PACKAGE OUTLINE
RSE0008A
UQFN - 0.6 mm max height
SCALE 7.000
PLASTIC QUAD FLATPACK - NO LEAD
1.55
1.45
B
A
PIN 1 INDEX AREA
1.55
1.45
C
0.6
0.5
SEATING PLANE
0.05
0.00
0.05 C
2X
0.1
0.05
0.35
0.25
6X
C A B
C
0.4
0.3
2X
4
3
(0.12)
TYP
0.45
0.35
5
SYMM
2X
1
2X
7
1
4X 0.5
8
SYMM
PIN 1 ID
(45 X 0.1)
4X
0.25
0.15
0.1
0.05
C A B
C
0.3
0.2
0.1
0.05
C A B
C
4220323/B 03/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
RSE0008A
UQFN - 0.6 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
SYMM
(R0.05) TYP
2X (0.6)
8
6X (0.55)
7
1
4X (0.25)
SYMM
(1.3)
2X
(0.2)
4X (0.5)
5
3
4
2X (0.3)
(1.35)
LAND PATTERN EXAMPLE
SCALE:30X
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
METAL
UNDER
SOLDER MASK
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4220323/B 03/2018
NOTES: (continued)
3. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271).
www.ti.com
EXAMPLE STENCIL DESIGN
RSE0008A
UQFN - 0.6 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
SYMM
(R0.05) TYP
8
2X (0.6)
6X (0.55)
7
1
4X (0.25)
SYMM
(1.3)
4X (0.5)
2X (0.2)
5
3
4
2X
(0.3)
(1.35)
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICKNESS
SCALE: 30X
4220323/B 03/2018
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
PACKAGE OUTLINE
YZP0008
DSBGA - 0.5 mm max height
SCALE 8.000
DIE SIZE BALL GRID ARRAY
B
A
E
BALL A1
CORNER
D
C
0.5 MAX
SEATING PLANE
0.19
0.15
0.05 C
BALL TYP
0.5 TYP
D
C
SYMM
1.5
TYP
0.5
TYP
8X
0.015
D: Max = 1.918 mm, Min =1.858 mm
B
0.25
0.21
C A B
E: Max = 0.918 mm, Min =0.858 mm
A
1
2
SYMM
4223082/A 07/2016
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
YZP0008
DSBGA - 0.5 mm max height
DIE SIZE BALL GRID ARRAY
(0.5) TYP
8X ( 0.23)
2
1
A
(0.5) TYP
B
SYMM
C
D
SYMM
LAND PATTERN EXAMPLE
SCALE:40X
SOLDER MASK
OPENING
0.05 MAX
( 0.23)
SOLDER MASK
OPENING
0.05 MIN
( 0.23)
METAL
METAL UNDER
SOLDER MASK
NON-SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4223082/A 07/2016
NOTES: (continued)
3. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
For more information, see Texas Instruments literature number SNVA009 (www.ti.com/lit/snva009).
www.ti.com
EXAMPLE STENCIL DESIGN
YZP0008
DSBGA - 0.5 mm max height
DIE SIZE BALL GRID ARRAY
(0.5) TYP
8X ( 0.25)
(R0.05) TYP
1
2
A
(0.5)
TYP
B
SYMM
C
METAL
TYP
D
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
SCALE:40X
4223082/A 07/2016
NOTES: (continued)
4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising