Texas Instruments | TL431LI / TL432LI Programmable Shunt Regulator with Optimized Reference Current (Rev. A) | Datasheet | Texas Instruments TL431LI / TL432LI Programmable Shunt Regulator with Optimized Reference Current (Rev. A) Datasheet

Texas Instruments TL431LI / TL432LI Programmable Shunt Regulator with Optimized Reference Current (Rev. A) Datasheet
Product
Folder
Order
Now
Support &
Community
Tools &
Software
Technical
Documents
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
TL431LI / TL432LI Programmable Shunt Regulator with Optimized Reference Current
1 Features
3 Description
•
The TL431LI device is a three-terminal adjustable
shunt regulator, with specified thermal stability over
applicable automotive, commercial, and military
temperature ranges. The output voltage can be set to
any value between Vref (approximately 2.495 V) and
36 V, with two external resistors. These devices have
a typical output impedance of 0.3 Ω. Active output
circuitry provides a very sharp turn-on characteristic,
making these devices excellent replacements for
Zener diodes in many applications, such as onboard
regulation, adjustable power supplies, and switching
power supplies. This device is a pin-to-pin alternative
to the industry standard TL431, with optimized Iref and
IIdev performance. The lower Iref and IIdev values
enable designers to achieve higher system accuracy
and lower leakage current. The TL432LI device has
exactly the same functionality and electrical
specifications as the TL431LI device, but has a
different pinout for the DBZ package.
1
•
•
•
•
•
•
•
•
Reference Voltage Tolerance at 25°C
– 0.5% (B Grade)
– 1% (A Grade)
Minimum Typical Output Voltage: 2.495 V
Adjustable Output Voltage: Vref to 36 V
Operation From −40°C to +125°C (Q Temp)
Maximum Temperature Drift
– 10 mV (C Temp)
– 17 mV (I Temp)
– 27 mV (Q Temp)
0.3-Ω Typical Output Impedance
Sink-Current Capability
– Imin = 1 mA (max)
– IKA = 15 mA (max)
Reference Input Current IREF: 0.4 μA (max)
Deviation of Reference Input Current over
Temperature, II(dev): 0.3 μA (max)
The TL431LI device is offered in two grades, with
initial tolerances (at 25°C) of 0.5% and 1%, for the B
and A grade, respectively. In addition, low output drift
versus temperature ensures good stability over the
entire temperature range.
2 Applications
•
•
•
•
•
•
Adjustable Voltage and Current Referencing
Secondary Side Regulation in Flyback SMPS
Zener Diode Replacement
Voltage Monitoring
Precision Constant Current Sink/Source
Comparator with Integrated Reference
The TL43xLIxQ devices are
operation from –40°C to 125°C.
characterized
for
Device Information(1)
PART NUMBER
TL43xLI
PACKAGE (PIN)
SOT-23 (3)
BODY SIZE (NOM)
2.90 mm x 1.30 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
VKA
Input
IKA
Vref
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
4
7.1
7.2
7.3
7.4
7.5
7.6
4
4
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Thermal Information ..................................................
Recommended Operating Conditions.......................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Parameter Measurement Information .................. 9
8.1 Temperature Coefficient............................................ 9
8.2 Dynamic Impedance ............................................... 10
9
Detailed Description ............................................ 11
9.1 Overview ................................................................. 11
9.2 Functional Block Diagram ....................................... 11
9.3 Feature Description................................................. 12
9.4 Device Functional Modes........................................ 12
10 Applications and Implementation...................... 13
10.1 Application Information.......................................... 13
10.2 Typical Applications .............................................. 13
10.3 System Examples ................................................. 21
11 Power Supply Recommendations ..................... 24
12 Layout................................................................... 24
12.1 Layout Guidelines ................................................. 24
12.2 Layout Example .................................................... 25
13 Device and Documentation Support ................. 26
13.1
13.2
13.3
13.4
13.5
13.6
13.7
Related Links ........................................................
Documentation Support ........................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
26
26
26
26
27
27
27
14 Mechanical, Packaging, and Orderable
Information ........................................................... 27
4 Revision History
Changes from Original (July 2018) to Revision A
•
2
Page
Changed TL43xLI status from Advance Information to Production Data release ................................................................. 1
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
5 Device Comparison Table
DEVICE PINOUT
INITIAL ACCURACY
OPERATING FREE-AIR TEMPERATURE (TA)
TL431LI
TL432LI
A: 1%
B: 0.5%
C: 0°C to 70°C
I: -40°C to 85°C
Q: -40°C to 125°C
6 Pin Configuration and Functions
TL431LI DBZ Package
3-Pin SOT-23
Top View
CATHODE
TL432LI DBZ Package
3-Pin SOT-23
Top View
1
3
ANODE
REF
1
CATHODE
2
3
ANODE
2
REF
Pin Functions
PIN NUMBER
NAME
TL431LIx
TL432LIx
DBZ
DBZ
TYPE
DESCRIPTION
ANODE
3
3
O
Common pin, normally connected to ground
CATHODE
1
2
I/O
Shunt Current/Voltage input
REF
2
1
I
Threshold relative to common anode
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
3
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
VKA
Cathode Voltage (2)
IKA
Continuos Cathode Current Range
II(ref)
Reference Input Current
TJ
Tstg
(1)
(2)
MAX
UNIT
37
V
–10
18
mA
–5
10
mA
Operating Junction Temperature Range
–40
150
C
Storage Temperature Range
–65
150
C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to ANODE, unless otherwise noted.
7.2 ESD Ratings
VALUE
Electrostatic
discharge
V(ESD)
(1)
(2)
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001pins (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22- ±1000
VC101 (2)
±1000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Thermal Information
TL43xLI
THERMAL METRIC (1)
DBZ
UNIT
3 PINS
RθJA
Junction-to-ambient thermal resistance
371.7
C/W
RθJC(top)
Junction-to-case (top) thermal resistance
145.9
C/W
RθJB
Junction-to-boardthermal resistance
104.7
C/W
ψJT
Junction-to-top characterization resistance
23.9
C/W
ψJB
Junction-to-board characterization resistance
102.9
C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
7.4 Recommended Operating Conditions
See
(1)
VKA
Cathode Voltage
IKA
Continuous Cathode Current Range
MIN
MAX
VREF
36
V
1
15
mA
0
70
C
TL43xLIxI
–40
85
C
TL43xLIxQ
–40
125
C
TL43xLIxC
TA
(1)
4
Operating Free-Air Temperature
UNIT
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
7.5 Electrical Characteristics
over recommended operating conditions, TA = 25°C (unless otherwise noted)
PARAMETER
Vref
TEST CIRCUIT
Reference Voltage
See Figure 14
Deviation of reference
input voltage over full
temperature range (1)
ΔVref /
ΔVKA
Ratio of change in
reference voltage to the
change in cathode
voltage
Iref
Reference Input Current See Figure 15
II(dev)
Deviation of reference
input current over full
temperature range (1)
Imin
Minimum cathode
current for regulation
Ioff
Off-state cathode
current
|ZKA|
(1)
(2)
Dynamic Impedance
VKA = Vref, IKA = 1 mA
MIN
See Figure 14
VKA = Vref, IKA = 1 mA
TYP MAX
UNIT
TL43xLIAx devices
2470 2495 2520
mV
TL43xLIBx devices
2483 2495 2507
mV
TL43xLIxC devices
VI(dev)
(2)
TEST CONDITIONS
TL43xLIxI devices
TL43xLIxQ devices
2.5
11
mV
6
17
mV
10
27
–1.4
–2.7
mV/V
–1
–2
mV/V
IKA = 1 mA, R1 = 10kΩ, R2 = ∞
0.2
0.4
µA
See Figure 15
IKA = 1 mA, R1 = 10kΩ, R2 = ∞
0.1
0.3
µA
See Figure 14
VKA = Vref
1
mA
See Figure 16
VKA = 36 V, Vref = 0
0.1
1
µA
See Figure 14
VKA = Vref, IKA = 1 mA to 15 mA
0.3
0.65
Ω
ΔVKA = 10 V - Vref
See Figure 15
IKA = 1 mA
ΔVKA = 36 V - 10 V
mV
The deviation parameters VI(dev) and II(dev) are defined as the differences between the maximum and minimum values obtained over the
rated temperature range. For more details on VI(dev) and how it relates to the average temperature coefficient, see Parameter
Measurement Information.
The dynamic impedance is defined by |ZKA| = ΔVKA/ΔIKA. For more details on |ZKA| and how it relates to VKA, see Parameter
Measurement Information.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
5
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
7.6 Typical Characteristics
Data at high and low temperatures are applicable only within the recommended operating free-air temperature
ranges of the various devices.
1
2.5005
0.9
Iref - Reference Current - µA
Vref - Reference Voltage - V
Vka = Vref
2.499 I = 1 mA
KA
2.4975
2.496
2.4945
2.493
2.4915
2.49
2.4885
0.7
0.6
0.5
0.4
0.3
0.2
0
-50
-25
0
25 50 75 100 125 150
TA - Free-Air Temperature - °C
D001
Book
Figure 1. Reference Voltage vs Free-Air Temperature
-25
0
25
50
75 100
TA - Free-Air Temperature - °C
125
D002
Figure 2. Reference Current vs Free-Air Temperature
0.064
15
VKA = Vref
TA = 25°C
12
Ioff - Off-State Cathode Current - PA
IKA - Cathode Current - mA
0.8
0.1
2.487
2.4855
-50
IKA = 1 mA
9
6
3
0
0.5
1
1.5
2
2.5
VKA - Cathode Voltage -V
0.048
0.04
0.032
0.024
0.016
0.008
0
-50
-3
0
VKA = 36 V
0.056 VREF = 0 V
3
-25
0
25
50
75 100
TA - Free-Air Temperature - °C
125
D003
D004
Figure 4. Off-State Cathode Current
vs Free-Air Temperature
Figure 3. Cathode Current vs Cathode Voltage
-1.05
VKA = 3 V to 36 V
Y AXIS TITLE (Unit)
-1.2
-1.35
-1.5
-1.65
-1.8
-50
-25
0
25
50
75
Temperature (°C)
100
125
D006
Figure 5. Ratio of Delta Reference Voltage to Delta Cathode Voltage vs Free-Air Temperature
6
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
75
IKA = 10 mA
TA = 25°C
200
Gain
Phase
60
160
45
120
30
80
15
Phase - Degrees
AV - Small-Signal Voltage Amplification - dB
Typical Characteristics (continued)
Output
IKA
15 kΩ
9 µF
+
40
−
8.25 kΩ
0
100
1k
10k
100k
f - Frequency - Hz
0
10M
1M
Gain
Figure 6. Small-Signal Voltage Amplification
vs Frequency
GND
Figure 7. Test Circuit for Voltage Amplification
100
|ZKA| - Reference Impedance - Ohms
232 Ω
1 kΩ
IKA = 10 mA
50 T = 25°C
A
30
20
Output
IKA
10
50 Ω
5
3
2
−
+
1
GND
0.5
0.3
0.2
0.1
1k
10k
100k
f - Frequency - Hz
1M
D005
Figure 9. Test Circuit for Reference Impedance
Figure 8. Reference Impedance vs Frequency
6
Input and Output Voltage - V
Input
220 Ω
TA = 25qC
Output
5
4
3
Pulse
Generator
f = 100 kHz
Output
2
50 Ω
1
GND
0
-1
0
1
2
3
4
t - Time - Ps
5
6
7
puls
Figure 10. Pulse Response
Figure 11. Test Circuit for Pulse Response
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
7
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
Typical Characteristics (continued)
150 Ω
IKA - Cathode Current - mA
15
12
A VKA = Vref
B VKA = 5 V
C VKA = 10 V
IKA
+
VBATT
CL
Stable Region
−
9
6
TEST CIRCUIT FOR CURVE A
3
0
0.001
IKA
0.01
0.1
1
CL - Load Capacitance - µF
R1 = 10 kΩ
10
Copy
TL43
The areas under the curves represent conditions that may cause the
device to oscillate. For curves B and C, R2 and V+ are adjusted to
establish the initial VKA and IKA conditions, with CL = 0. VBATT and CL
then are adjusted to determine the ranges of stability.
Figure 12. Stability Boundary Conditions for All TL431LI,
TL432LI Devices
150 Ω
CL
+
R2
VBATT
−
TEST CIRCUIT FOR CURVES B, C, AND D
Figure 13. Test Circuits for Stability Boundary Conditions
8
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
8 Parameter Measurement Information
VKA
Input
IKA
Vref
Figure 14. Test Circuit for VKA = Vref
Input
VKA
IKA
R1
Iref
R2
Vref
R1 ö
æ
VKA = Vref ç 1 +
÷ + Iref × R1
R2 ø
è
Figure 15. Test Circuit for VKA > Vref
Input
VKA
Ioff
Figure 16. Test Circuit for Ioff
8.1 Temperature Coefficient
The deviation of the reference voltage, Vref, over the full temperature range is known as VI(dev). The parameter of
VI(dev) can be used to find the temperature coefficient of the device. The average full-range temperature
coefficient of the reference input voltage, αVref, is defined as:
αVref is positive or negative, depending on whether minimum Vref or maximum Vref, respectively, occurs at the
lower temperature. The full-range temperature coefficient is an average and therefore any subsection of the rated
operating temperature range can yield a value that is greater or less than the average. For more details on
temperature coefficient, check out Voltage Reference Selection Basics.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
9
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
8.2 Dynamic Impedance
'VKA
'IKA . When the device is operating with two external resistors
The dynamic impedance is defined as:
'V
z'
'I which is approximately equal to
(see Figure 15), the total dynamic impedance of the circuit is given by:
R1 ·
§
ZKA ¨ 1
¸
© R2 ¹ .
ZKA
Itest
P/
IKA (mA)
The VKA of the TL431LI can be affected by the dynamic impedance. The TL431LI test current Itest for VKA is
specified on the Eletrical Characteristics . Any deviation from Itest can cause deviation on the output VKA.
Figure 17 shows the effect of the dynamic impedance on the VKA.
IKA
IKA(min)
0
VKA (V)
Ps
Figure 17. Dynamic Impedance
10
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
9 Detailed Description
9.1 Overview
This standard device has proven ubiquity and versatility across a wide range of applications, ranging from power
to signal path. This is due to its key components containing an accurate voltage reference and op amp, which
are very fundamental analog building blocks. TL43xLI is used in conjunction with it's key components to behave
as a single voltage reference, error amplifier, voltage clamp or comparator with integrated reference.
TL43xLI can be operated and adjusted to cathode voltages from 2.495V to 36V, making this part optimum for a
wide range of end equipments in industrial, auto, telecom and computing. In order for this device to behave as a
shunt regulator or error amplifier, >1mA (Imin(max)) must be supplied in to the cathode pin. Under this condition,
feedback can be applied from the Cathode and Ref pins to create a replica of the internal reference voltage.
Various reference voltage options can be purchased with initial tolerances (at 25°C) of 0.5%, and 1%. These
reference options are denoted by B (0.5%) and A (1.0%) after the TL431LI or TL432LI. TL431LI and TL432LI are
both functionally the same, but have separate pinout options.
The TL43xLIxC devices are characterized for operation from 0°C to 70°C, the TL43xLIxI devices are
characterized for operation from –40°C to 85°C, and the TL43xLIxQ devices are characterized for operation from
–40°C to 125°C.
9.2 Functional Block Diagram
CATHODE
+
REF
_
Vref
ANODE
Figure 18. Equivalent Schematic
CATHODE
REF
ANODE
Figure 19. Detailed Schematic
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
11
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
9.3 Feature Description
TL43xLI consists of an internal reference and amplifier that outputs a sink current based on the difference
between the reference pin and the virtual internal pin. The sink current is produced by the internal Darlington
pair, shown in the above schematic (Figure 19). A Darlington pair is used in order for this device to be able to
sink a maximum current of 15 mA.
When operated with enough voltage headroom (≥ 2.495 V) and cathode current (IKA), TL43xLI forces the
reference pin to 2.495 V. However, the reference pin can not be left floating, as it needs IREF ≥ 0.4 µA (please
see Specifications). This is because the reference pin is driven into an npn, which needs base current in order
operate properly.
When feedback is applied from the Cathode and Reference pins, TL43xLI behaves as a Zener diode, regulating
to a constant voltage dependent on current being supplied into the cathode. This is due to the internal amplifier
and reference entering the proper operating regions. The same amount of current needed in the above feedback
situation must be applied to this device in open loop, servo or error amplifying implementations in order for it to
be in the proper linear region giving TL43xLI enough gain.
Unlike many linear regulators, TL43xLI is internally compensated to be stable without an output capacitor
between the cathode and anode. However, if it is desired to use an output capacitor Figure 12 can be used as a
guide to assist in choosing the correct capacitor to maintain stability.
9.4 Device Functional Modes
9.4.1 Open Loop (Comparator)
When the cathode/output voltage or current of TL43xLI is not being fed back to the reference/input pin in any
form, this device is operating in open loop. With proper cathode current (Ika) applied to this device, TL43xLI will
have the characteristics shown in Figure 18. With such high gain in this configuration, TL43xLI is typically used
as a comparator. With the reference integrated makes TL43xLI the preferred choice when users are trying to
monitor a certain level of a single signal. Look at SLVA987 for more details on open loop comparator applications
on the TL431LI.
9.4.2 Closed Loop
When the cathode/output voltage or current of TL43xLI is being fed back to the reference/input pin in any form,
this device is operating in closed loop. The majority of applications involving TL43xLI use it in this manner to
regulate a fixed voltage or current. The feedback enables this device to behave as an error amplifier, computing
a portion of the output voltage and adjusting it to maintain the desired regulation. This is done by relating the
output voltage back to the reference pin in a manner to make it equal to the internal reference voltage, which can
be accomplished through resistive or direct feedback.
12
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
10 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
As this device has many applications and setups, there are many situations that this datasheet can not
characterize in detail. The linked application notes help the designer make the best choices when using this part.
Application note Designing with the Improved TL431LI, SNOAA00 provides a deeper understanding of this
device's accuracy in a flyback optocoupler application. Application note Setting the Shunt Voltage on an
Adjustable Shunt Regulator, SLVA445 assists designers in setting the shunt voltage to achieve optimum
accuracy for this device.
10.2 Typical Applications
10.2.1 Comparator With Integrated Reference
Vsup
Rsup
Vout
CATHODE
R1
VIN
RIN
REF
VL
+
R2
2.5V
ANODE
Figure 20. Comparator Application Schematic
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
13
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
Typical Applications (continued)
10.2.1.1 Design Requirements
For this design example, use the parameters listed in Table 1 as the input parameters.
Table 1. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Input Voltage Range
0 V to 5 V
Input Resistance
10 kΩ
Supply Voltage
24 V
Cathode Current (Ik)
5 mA
Output Voltage Level
~2 V – VSUP
Logic Input Thresholds VIH/VIL
VL
10.2.1.2 Detailed Design Procedure
When using TL43xLI as a comparator with reference, determine the following:
• Input Voltage Range
• Reference Voltage Accuracy
• Output logic input high and low level thresholds
• Current Source resistance
10.2.1.2.1 Basic Operation
In the configuration shown in Figure 20 TL43xLI will behave as a comparator, comparing the VREF pin voltage to
the internal virtual reference voltage. When provided a proper cathode current (IK), TL43xLI will have enough
open loop gain to provide a quick response. This can be seen in Figure 21, where the RSUP=10 kΩ (IKA=500 µA)
situation responds much slower than RSUP=1 kΩ (IKA=5 mA). With the TL43xLI max Operating Current (IMIN)
being 1 mA, operation below that could result in low gain, leading to a slow response.
10.2.1.2.1.1 Overdrive
Slow or inaccurate responses can also occur when the reference pin is not provided enough overdrive voltage.
This is the amount of voltage that is higher than the internal virtual reference. The internal virtual reference
voltage will be within the range of 2.495 V ±(0.5% or 1.0%) depending on which version is being used. The more
overdrive voltage provided, the faster the TL43xLI will respond.
For applications where TL43xLI is being used as a comparator, it is best to set the trip point to greater than the
positive expected error (that is +1.0% for the A version). For fast response, setting the trip point to >10% of the
internal VREF should suffice.
For minimal voltage drop or difference from Vin to the ref pin, TI recommends to use an input resistor <10 kΩ to
provide Iref.
14
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
10.2.1.2.2 Output Voltage and Logic Input Level
In order for TL43xLI to properly be used as a comparator, the logic output must be readable by the receiving
logic device. This is accomplished by knowing the input high and low level threshold voltage levels, typically
denoted by VIH and VIL.
As seen in Figure 21, TL43xLI's output low level voltage in open-loop/comparator mode is approximately 2 V,
which is typically sufficient for 5 V supplied logic. However, would not work for 3.3 V and 1.8 V supplied logic. To
accommodate this a resistive divider can be tied to the output to attenuate the output voltage to a voltage legible
to the receiving low voltage logic device.
TL43xLI's output high voltage is equal to VSUP due to TL43xLI being open-collector. If VSUP is much higher than
the receiving logic's maximum input voltage tolerance, the output must be attenuated to accommodate the
outgoing logic's reliability.
When using a resistive divider on the output, be sure to make the sum of the resistive divider (R1 and R2 in
Figure 20) is much greater than RSUP in order to not interfere with TL43xLI's ability to pull close to VSUP when
turning off.
10.2.1.2.2.1 Input Resistance
TL43xLI requires an input resistance in this application in order to source the reference current (IREF) needed
from this device to be in the proper operating regions while turning on. The actual voltage seen at the ref pin will
be VREF=VIN-IREFRIN. Because IREF can be as high as 0.4 µA it is recommended to use a resistance small enough
that will mitigate the error that IREF creates from VIN.
10.2.1.3 Application Curve
5.5
5
4.5
4
Voltage (V)
3.5
3
2.5
2
1.5
1
Vin
Vka(Rsup=10k:)
Vka(Rsup=1k:)
0.5
0
-0.5
-0.001
-0.0006
-0.0002
0.0002
Time (s)
0.0006
0.001
D001
Figure 21. Output Response With Various Cathode Currents
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
15
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
10.2.2 Precision Constant Current Sink
VI(BATT)
IO
IO =
TL43xLIx
Vref
RS
RS
0.1%
Copyright © 2017, Texas Instruments Incorporated
Figure 22. Precision Constant Current Sink Application Schematic
10.2.2.1 Design Requirements
For this design example, use the parameters listed in Table 1 as the input parameters.
Table 2. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Supply Voltage (VI(BATT))
5V
Sink Current (IO)
100mA
Cathode Current (Ik)
5 mA
10.2.2.2 Detailed Design Procedure
When using TL43xLI as a constant current sink, determine the following:
• Output Current Range
• Output Current Accuracy
• Power Consumption for TL43xLI
10.2.2.2.1 Basic Operation
In the configuration shown, TL43xLI acts as a control component within a feedback loop of the constant current
sink. Working with an external passing component such as an BJT, TL43xLI provides precision current sink with
accuracy set by itself and the sense resistor RS. This circuit can also be used as LED driving circuit.
10.2.2.2.1.1 Output Current Range and Accuracy
The output current range of the circuit is determined by the equation shown in the configuration. Keep in mind
that the VREF equals to 2.495V. When choosing the sense resistor RS, it needs to generate 2.495V for the
TL43xLI when IO reaches the target current. If the overhead voltage of 2.495V is not acceptable, please consider
lower voltage reference devices such as TLV43x or TLVH43x.
The output current accuracy is determined by both the accuracy of TL43xLI chosen, as well as the accuracy of
the sense resistor RS. The internal virtual reference voltage of TL43xLI will be within the range of 2.495 V ±(0.5%
or 1.0%) depending on which version is being used. Another consideration for the output current accuracy is the
temperature coefficient of the TL43xLI and RS. Please refer to the electrical characterization table for the
specification of these parameters.
10.2.2.2.2 Power Consumption
In order for TL43xLI to properly be used as a control component in this circuit, the minimum operating current
needs to be reached. This is accomplished by setting the external biasing resistor in series with the TL43xLI.
For TL43xLI, the minimum operating current is 1mA and with margin consideration, most of the designs set this
current to be higher than 1mA. To achieve lower power consumption, please consider devices such as ATL43x
and ATL43xLI.
16
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
10.2.3 Shunt Regulator/Reference
RSUP
VSUP
VO = ( 1 +
R1
0.1%
CATHODE
REF
Vr ef
R1
) Vref
R2
R2
0.1%
TL43xLIx
ANODE
CL
Copyright © 2017, Texas Instruments Incorporated
Figure 23. Shunt Regulator Schematic
10.2.3.1 Design Requirements
For this design example, use the parameters listed in Table 1 as the input parameters.
Table 3. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Reference Initial Accuracy
1.0 %
Supply Voltage
24 V
Cathode Current (Ik)
5 mA
Output Voltage Level
2.495 V - 36 V
Load Capacitance
2 µF
Feedback Resistor Values and Accuracy (R1 and R2)
10 kΩ
10.2.3.2 Detailed Design Procedure
When using TL43xLI as a Shunt Regulator, determine the following:
• Input Voltage Range
• Temperature Range
• Total Accuracy
• Cathode Current
• Reference Initial Accuracy
• Output Capacitance
10.2.3.2.1
Programming Output/Cathode Voltage
In order to program the cathode voltage to a regulated voltage a resistive bridge must be shunted between the
cathode and anode pins with the mid point tied to the reference pin. This can be seen in Figure 23, with R1 and
R2 being the resistive bridge. The cathode/output voltage in the shunt regulator configuration can be
approximated by the equation shown in Figure 23. The cathode voltage can be more accurate determined by
taking in to account the cathode current:
Vo=(1+R1/R2)VREF-IREFR1
(1)
In order for this equation to be valid, TL43xLI must be fully biased so that it has enough open loop gain to
mitigate any gain error. This can be done by meeting the Imin spec denoted in Specifications.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
17
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
10.2.3.2.2 Total Accuracy
When programming the output above unity gain (VKA=VREF), TL43xLI is susceptible to other errors that may
effect the overall accuracy beyond VREF. These errors include:
•
•
•
•
R1 and R2 accuracies
VI(dev) - Change in reference voltage over temperature
ΔVREF / ΔVKA - Change in reference voltage to the change in cathode voltage
|zKA| - Dynamic impedance, causing a change in cathode voltage with cathode current
Worst case cathode voltage can be determined taking all of the variables in to account. Application note Setting
the Shunt Voltage on an Adjustable Shunt Regulator, SLVA445 assists designers in setting the shunt voltage to
achieve optimum accuracy for this device.
10.2.3.2.3 Stability
Though TL43xLI is stable with no capacitive load, the device that receives the shunt regulator's output voltage
could present a capacitive load that is within the TL43xLI region of stability, shown in Figure 12. Also, designers
may use capacitive loads to improve the transient response or for power supply decoupling. When using
additional capacitance between Cathode and Anode, refer to Figure 12. Also, application note Understanding
Stability Boundary Conditions Charts in TL431, TL432 Data Sheet, SLVA482 provides a deeper understanding of
this devices stability characteristics and aid the user in making the right choices when choosing a load capacitor.
10.2.3.2.4 Start-up Time
As shown in Figure 24, TL43xLI has a fast response up to approximately 2 V and then slowly charges to it's
programmed value. This is due to the compensation capacitance (shown in Figure 19) the TL43xLI has to meet
it's stability criteria. Despite the secondary delay, TL43xLI still has a fast response suitable for many clamp
applications.
10.2.3.3 Application Curve
27
Vsup
Vka=Vref
R1=10k: & R2=10k:
R1=38k: & R2=10k:
24
21
Voltage (V)
18
15
12
9
6
3
0
-3
-6
-5E-6
-3E-6
-1E-6
1E-6
Time (s)
3E-6
5E-6
D001
Figure 24. TL43xLI Start-Up Response
18
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
10.2.4 Isolated Flyback with Optocoupler
VOUT
VIN AC
VDD
VPC
VDD
VSC
HV
UCC28740
PWM Controller
VS
UCC24636
SR Controller
DRV
DRV
FB
TBLK
CS
TL431LI
GND
Copyright © 2018, Texas Instruments Incorporated
Figure 25. Isolated Flyback with Optocoupler
10.2.4.1 Design Requirements
The TL431LI is used in the feedback network on the secondary side in an isolated flyback with optocoupler
design. Figure 25 shows the simplified flyback converter with the TL431LI. For this design example, use the
parameters in Table 4 as the input parameters. In this example, a simplified design procedure will be discussed.
The compensation network for the feedback network is beyond the scope of this section. Details on
compensation network can be found on SLUA671.
Table 4. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Voltage Output
15 V
Secondary Side Feedback Loop Accuracy
< 3%
10.2.4.1.1 Detailed Design Procedure
The goal of this design is to design a high accuracy feedback network to meet 3% VOUT accuracy requirements
over the full temperature range. To meet the design requirements, the total secondary side feedback loop error
will have to be below 3%. In order to meet these requirements it is necessary to take full advantage of the
improved temperature drift, Iref(min), and II(dev) of the TL431LI.
VOUT
Rs
Error|Iref
R1 = 40.2 lQ
IREF
TL431LIBI
Error|Vref
R2 = 8.06 lQ
Copyright © 2017, Texas Instruments Incorporated
Figure 26. Feedback Quiescent Current
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
19
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
10.2.4.1.1.1 TL431 Feedback Loop Error Calculation
Figure 26 shows the simplified version of the feedback network. The accuracy of the output voltage is dependent
on the regulation voltage accuracy of the TL431LI. A simplified VOUT can be seen in Equation 2 but this equation
does not include errors that will deviate the output.
R1
VOUT Vref u (1
) R1u (Iref )
R2
40.2k:
VOUT (2.495 V) u (1
) 40.2k: u (0.4 PA)
8.06k:
VOUT
14.955 V
(2)
The primary sources of error are the Error|Vref and Error|Iref. The Error|Vref primarily consists of the errors that
affect the internal bandgap voltage reference of the TL431LI. This consists of errors from the initial accuracy,
temperature drift, ratio of change in reference voltage to the change in cathode voltage, and dynamic impedance.
The benefit of the TL431LI is its low temperature drift, VI(dev), which allows the Vref to be more accurate across
the full temperature range compared to typical TL431LI devices. Equation 3 shows a simplified worst case Vref
with initial accuracy and temperature drift.
Vref (Error |Vref ) Vref u (1 Initial Accuracy) VI(dev) ...
Vref (Error |Vref )
2.495 V u (1 0.5%) 17mV ...
Vref (Error |Vref ) | 2.524 V
(3)
The Error|Iref in Figure 26 is dependent on the Iref and II(dev) along with R1. The TL431LI has improved Iref and
II(dev) which allows the values of the resistor R1 to be increased to save power. Typically optocoupler feedback
design requires the Iref to be taken into account when doing VOUT calculations but the error comes from the
deviation from the maximum to typical value of Iref. In addition to this, the II(dev) is the temperature deviation on
the Iref current which will affect the overall reference current into the TL431LI. Equation 4 shows the VOUT of the
TL431LI for Figure 26 which includes the improved Iref and II(dev). The VOUT equation assumes that the resistors
R1 and R2 have a 0.5% accuracy tolerance.
R1
VOUT (Error |Iref ) Vref (Error |Vref ) u (1
) R1 u (Iref II(dev) )
R2
40.2k: u (1 0.5%)
VOUT (Error |Iref ) (2.495 V u (1 0.5%) 0.017 V) u (1
)
8.06k: u (1 0.5%)
40.2k: u (1 0.5%) u (0.4 PA 0.3 PA)
VOUT 15.270 V
(4)
Comparing the calculated VOUT without and without error the expected worst case max error is 2.1% which meets
the 3% error target.
20
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
10.3 System Examples
VI(BATT)
R
(see Note A)
2N222
2N222
30 Ω
4.7 kΩ
0.01 µF
TL43xLIx
VO
R2
0.1%
R1
0.1%
R1 ö
æ
VO = ç 1 +
÷ Vref
R2 ø
è
Copyright © 2017, Texas Instruments Incorporated
A.
R should provide cathode current ≥1 mA to the TL431LI at minimum V(BATT).
Figure 27. Precision High-Current Series Regulator
VI(BATT)
IN
uA7805
OUT
Common
VO
R1
TL43xLIx
(
(
VO = 1 + R1 Vref
R2
Minimum V
V + 5V
O = ref
R2
Copyright © 2017, Texas Instruments Incorporated
Figure 28. Output Control of a Three-Terminal Fixed Regulator
VO
VI(BATT)
(
R2
(
VO = 1 + R1 Vref
R2
R1
TL43xLIx
Copyright © 2017, Texas Instruments Incorporated
Figure 29. High-Current Shunt Regulator
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
21
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
System Examples (continued)
VI(BATT)
VO
R1
TL43xLIx
C
(see Note A)
R2
Copyright © 2017, Texas Instruments Incorporated
A.
Refer to the stability boundary conditions in Figure 12 to determine allowable values for C.
Figure 30. Crowbar Circuit
IN
VI(BATT)
LM317
8.2 kΩ
OUT
VO ≈5 V, 1.5 A
Adjust
243 Ω
0.1%
TL43xLIx
243 Ω
0.1%
Copyright © 2017, Texas Instruments Incorporated
Figure 31. Precision 5-V, 1.5-A Regulator
VI(BATT)
VO ≈5 V
Rb
(see Note A)
27.4 kΩ
0.1%
TL43xLIx
27.4 kΩ
0.1%
Copyright © 2017, Texas Instruments Incorporated
A.
Rb should provide cathode current ≥1 mA to the TL431LI.
Figure 32. Efficient 5-V Precision Regulator
22
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
System Examples (continued)
12 V
VCC
6.8 kΩ
10 kΩ
5V
−
10 kΩ
0.1%
+
X
Not
Used
TL43xLIx
10 kΩ
0.1%
TL598
Feedback
Copyright © 2017, Texas Instruments Incorporated
Figure 33. PWM Converter With Reference
R3
(see Note A)
VI(BATT)
R4
(see Note A)
R1B
R1A
TL43xLIx
Low Limit = 1 + R1B V ref
R2B
High Limit = 1 + R1A V ref
R2A
R2A
LED on When Low Limit < VI(BATT) < High Limit
R2B
Copyright © 2017, Texas Instruments Incorporated
A.
Select R3 and R4 to provide the desired LED intensity and cathode current ≥1 mA to the TL431LI at the available
VI(BATT).
Figure 34. Voltage Monitor
650 Ω
12 V
R
2 kΩ
TL43xLIx
Off
On
C
æ
12 V
Delay = R × C × In çç
12
V
– Vref
è
ö
÷÷
ø
Copyright © 2017, Texas Instruments Incorporated
Figure 35. Delay Timer
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
23
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
System Examples (continued)
RCL
0.1%
VI(BATT)
IO
Iout =
R1
R1 =
TL43xLIx
V ref
+ IKA
R CL
V I(BATT)
I
O
h FE
+ IKA
Copyright © 2017, Texas Instruments Incorporated
Figure 36. Precision Current Limiter
VI(BATT)
IO
IO =
TL43xLIx
Vref
RS
RS
0.1%
Copyright © 2017, Texas Instruments Incorporated
Figure 37. Precision Constant-Current Sink
11 Power Supply Recommendations
When using TL43xLI as a Linear Regulator to supply a load, designers typically use a bypass capacitor on the
output/cathode pin. When doing this, be sure that the capacitance is within the stability criteria shown in
Figure 12.
In order to not exceed the maximum cathode current, be sure that the supply voltage is current limited. Also, be
sure to limit the current being driven into the Ref pin, as not to exceed it's absolute maximum rating.
For applications shunting high currents, pay attention to the cathode and anode trace lengths, adjusting the width
of the traces to have the proper current density.
12 Layout
12.1 Layout Guidelines
Bypass capacitors should be placed as close to the part as possible. Current-carrying traces need to have widths
appropriate for the amount of current they are carrying; in the case of the TL43xLIx, these currents are low.
24
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
12.2 Layout Example
TL43xLIx - DBZ
(TOP VIEW)
Rref
Vin
REF
1
Rsup
Vsup
ANODE
3
CATHODE
2
GND
CL
GND
Copyright © 2017, Texas Instruments Incorporated
Figure 38. DBZ Layout example
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
25
TL431LI
TL432LI
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
www.ti.com
13 Device and Documentation Support
13.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to order now.
Table 5. Related Links
PARTS
PRODUCT FOLDER
ORDER NOW
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
TL431LI
Click here
Click here
Click here
Click here
Click here
TL432LI
Click here
Click here
Click here
Click here
Click here
13.2 Documentation Support
13.2.1 Device Nomenclature
TI assigns suffixes and prefixes to differentiate all the combinations of the TL43xLI family. More details and
possible orderable combinations are located in the Package Option Addendum.
TL431LI X X XXX X
Product
1: TL431LI
2: TL432LI*
*(Cathode and REF
pins are switched)
Initial
Accuracy
B: 0.5%
A: 1%
Operating Free-Air
Temperature
C: 0°C to 70°C
I: -40°C to 85°C
Q: -40°C to 125°C
Package
Type
Package
Quantity
DBZ: SOT-23-3
R: Tape & Reel
13.2.2 Related Documentation
For related documentation see the following:
• Understanding Stability Boundary Conditions Charts in TL431, TL432 Data Sheet, SLVA482
• Setting the Shunt Voltage on an Adjustable Shunt Regulator, SLVA445
• Designing With the Improved TL431LI, SNOAA00
13.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
13.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
26
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
TL431LI
TL432LI
www.ti.com
SLVSDQ6A – JULY 2018 – REVISED NOVEMBER 2018
13.5 Trademarks
E2E is a trademark of Texas Instruments.
13.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
13.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Product Folder Links: TL431LI TL432LI
27
PACKAGE OPTION ADDENDUM
www.ti.com
5-Jun-2019
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TL431LIACDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
0 to 70
1TMP
TL431LIAIDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 85
1TOP
TL431LIAQDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 125
1BLP
TL431LIBCDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
0 to 70
1TNP
TL431LIBIDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 85
1TPP
TL431LIBQDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 125
1BMP
TL432LIACDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
0 to 70
1TQP
TL432LIAIDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 85
1TSP
TL432LIAQDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 125
1BNP
TL432LIBCDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
0 to 70
1TRP
TL432LIBIDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 85
1TTP
TL432LIBQDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 125
1BOP
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
5-Jun-2019
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TL431LI, TL432LI :
• Automotive: TL431LI-Q1, TL432LI-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jun-2019
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
TL431LIACDBZR
SOT-23
DBZ
3
3000
178.0
9.2
TL431LIACDBZR
SOT-23
DBZ
3
3000
178.0
TL431LIAIDBZR
SOT-23
DBZ
3
3000
178.0
TL431LIAIDBZR
SOT-23
DBZ
3
3000
TL431LIAQDBZR
SOT-23
DBZ
3
TL431LIAQDBZR
SOT-23
DBZ
TL431LIBCDBZR
SOT-23
DBZ
TL431LIBCDBZR
SOT-23
TL431LIBIDBZR
TL431LIBIDBZR
3.15
2.77
1.22
4.0
8.0
Q3
9.0
3.15
2.77
1.22
4.0
8.0
Q3
9.2
3.15
2.77
1.22
4.0
8.0
Q3
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
3000
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
3
3000
178.0
9.2
3.15
2.77
1.22
4.0
8.0
Q3
3
3000
178.0
9.2
3.15
2.77
1.22
4.0
8.0
Q3
DBZ
3
3000
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
SOT-23
DBZ
3
3000
178.0
9.2
3.15
2.77
1.22
4.0
8.0
Q3
SOT-23
DBZ
3
3000
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
TL431LIBQDBZR
SOT-23
DBZ
3
3000
178.0
9.2
3.15
2.77
1.22
4.0
8.0
Q3
TL431LIBQDBZR
SOT-23
DBZ
3
3000
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
TL432LIACDBZR
SOT-23
DBZ
3
3000
178.0
9.2
3.15
2.77
1.22
4.0
8.0
Q3
TL432LIACDBZR
SOT-23
DBZ
3
3000
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
TL432LIAIDBZR
SOT-23
DBZ
3
3000
178.0
9.2
3.15
2.77
1.22
4.0
8.0
Q3
TL432LIAIDBZR
SOT-23
DBZ
3
3000
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
TL432LIAQDBZR
SOT-23
DBZ
3
3000
178.0
9.2
3.15
2.77
1.22
4.0
8.0
Q3
TL432LIAQDBZR
SOT-23
DBZ
3
3000
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jun-2019
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
TL432LIBCDBZR
SOT-23
DBZ
3
3000
178.0
9.2
TL432LIBCDBZR
SOT-23
DBZ
3
3000
178.0
9.0
TL432LIBIDBZR
SOT-23
DBZ
3
3000
178.0
TL432LIBIDBZR
SOT-23
DBZ
3
3000
178.0
TL432LIBQDBZR
SOT-23
DBZ
3
3000
TL432LIBQDBZR
SOT-23
DBZ
3
3000
W
Pin1
(mm) Quadrant
3.15
2.77
1.22
4.0
8.0
Q3
3.15
2.77
1.22
4.0
8.0
Q3
9.0
3.15
2.77
1.22
4.0
8.0
Q3
9.2
3.15
2.77
1.22
4.0
8.0
Q3
178.0
9.0
3.15
2.77
1.22
4.0
8.0
Q3
178.0
9.2
3.15
2.77
1.22
4.0
8.0
Q3
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TL431LIACDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIACDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIAIDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIAIDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIAQDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIAQDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIBCDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIBCDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIBIDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIBIDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL431LIBQDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jun-2019
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TL431LIBQDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIACDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIACDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIAIDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIAIDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIAQDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIAQDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIBCDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIBCDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIBIDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIBIDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIBQDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
TL432LIBQDBZR
SOT-23
DBZ
3
3000
180.0
180.0
18.0
Pack Materials-Page 3
4203227/C
PACKAGE OUTLINE
DBZ0003A
SOT-23 - 1.12 mm max height
SCALE 4.000
SMALL OUTLINE TRANSISTOR
C
2.64
2.10
1.4
1.2
PIN 1
INDEX AREA
1.12 MAX
B
A
0.1 C
1
0.95
3.04
2.80
1.9
3X
3
0.5
0.3
0.2
2
(0.95)
C A B
0.25
GAGE PLANE
0 -8 TYP
0.10
TYP
0.01
0.20
TYP
0.08
0.6
TYP
0.2
SEATING PLANE
4214838/C 04/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC registration TO-236, except minimum foot length.
www.ti.com
EXAMPLE BOARD LAYOUT
DBZ0003A
SOT-23 - 1.12 mm max height
SMALL OUTLINE TRANSISTOR
PKG
3X (1.3)
1
3X (0.6)
SYMM
3
2X (0.95)
2
(R0.05) TYP
(2.1)
LAND PATTERN EXAMPLE
SCALE:15X
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
NON SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214838/C 04/2017
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBZ0003A
SOT-23 - 1.12 mm max height
SMALL OUTLINE TRANSISTOR
PKG
3X (1.3)
1
3X (0.6)
SYMM
3
2X(0.95)
2
(R0.05) TYP
(2.1)
SOLDER PASTE EXAMPLE
BASED ON 0.125 THICK STENCIL
SCALE:15X
4214838/C 04/2017
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising