Texas Instruments | TPS65218 Power Management for ARM Cortex-A8/A9 SOCs (Rev. D) | Datasheet | Texas Instruments TPS65218 Power Management for ARM Cortex-A8/A9 SOCs (Rev. D) Datasheet

Texas Instruments TPS65218 Power Management for ARM Cortex-A8/A9 SOCs (Rev. D) Datasheet
Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
Reference
Design
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
TPS65218 Power Management for ARM® Cortex™-A8/A9 SOCs
Not Recommended for New Designs
1 Device Overview
1.1
Features
1
• Three Adjustable Step-Down Converters With
Integrated Switching FETs (DCDC1, DCDC2,
DCDC3):
– DCDC1: 1.1-V Default, up to 1.8 A
– DCDC2: 1.1-V Default, up to 1.8 A
– DCDC3: 1.2-V Default, up to 1.8 A
– VIN Range From 2.7 V to 5.5 V
– Adjustable Output Voltage Range 0.85 V to
1.675 V (DCDC1 and DCDC2)
– Adjustable Output Voltage Range 0.9 V to 3.4 V
(DCDC3)
– Power Save Mode at Light Load Current
– 100% Duty Cycle for Lowest Dropout
– Active Output-Discharge When Disabled
• One Adjustable Buck-Boost Converter With
Integrated Switching FETs (DCDC4):
– DCDC4: 3.3 V Default, up to 1.6 A
– VIN Range From 2.7 V to 5.5 V
– Adjustable Output Voltage Range 1.175 V to 3.4
V
– Active Output-Discharge When Disabled
• Two Low-Quiescent Current, High Efficiency StepDown Converters for Battery Backup Domain
(DCDC5, DCDC6)
– DCDC5: 1-V Output
– DCDC6: 1.8-V Output
– VIN Range from 2.2 V to 5.5 V
– Supplied From System Power or Coin-Cell
Backup Battery
• Adjustable General-Purpose LDO (LDO1)
1.2
•
•
•
•
•
•
Applications
Industrial Automation
Electronic Point of Sale (ePOS)
1.3
•
– LDO1: 1.8-V Default up to 400 mA
– VIN Range From 1.8 V to 5.5 V
– Adjustable Output Voltage Range From 0.9 V to
3.4 V
– Active Output-Discharge When Disabled
Low-Voltage Load Switch (LS1) With 350-mA
Current Limit
– VIN Range From 1.2 V to 3.6 V
– 110-mΩ (Max) Switch Impedance at 1.35 V
5-V Load Switch (LS2) With 100-mA or 500-mA
Selectable Current Limit
– VIN Range From 4 V to 5.5 V
– 500-mΩ (Max) Switch Impedance at 5 V
High-Voltage Load Switch (LS3) With 100-mA or
500-mA Selectable Current Limit
– VIN Range From 1.8 V to 10 V
– 500-mΩ (Max) Switch Impedance
Supervisor With Built-in Supervisor Function
Monitors
– DCDC1, DCDC2 ±4% Tolerance
– DCDC3, DCDC4 ±5% Tolerance
– LDO1 ±5% Tolerance
Protection, Diagnostics, and Control:
– Undervoltage Lockout (UVLO)
– Always-on Push-Button Monitor
– Overtemperature Warning and Shutdown
– Separate Power-Good Output for Backup and
Main Supplies
– I2C Interface (Address 0x24) (See Timing
Requirements for I2C Operation at 400 kHz)
•
•
Test and Measurement
Personal Navigation
Description
The TPS65218 is a single chip power management IC, specifically designed to support both portable (LiIon battery) and non-portable (5-V adapter) applications. The device is characterized across a –40°C to
+105°C temperature range, making it suitable for a wide range of industrial applications.
Device Information (1)
PART NUMBER
TPS65218
(1)
PACKAGE
BODY SIZE (NOM)
VQFN (48)
6.00 mm × 6.00 mm
HTQFP (48)
7.00 mm × 7.00 mm
For all available packages, see the orderable addendum at the end of the data sheet.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
1.4
www.ti.com
Simplified Schematic
+
10 …F
VIO
VIO
1 …F
4.7 …F
CC
GPIO3
IN_BU
NC
NC
LS1
IN_LS1
IN_LS2
LS2
GPO2
IN_BIAS
INT_LDO
100 k
100 k
4.7 …F
4.7 …F
L3
10 …F
L6
1.5 µH
VDD_18
(DCDC6)
100 k
10 …F
1.5 µH
FB3
FB6
nWAKEUP
FB5
FB2
L5
L2
100 k
100 k
1.5 µH
22 …F
IN_nCC
DC34_SEL
nINT
PFI
PWR_EN
DCDC4
FB1
IN_DCDC4
GPIO1
L4A
VIO
100 k
100 k
nPFO
AC_DET
VIO
PGOOD
IN_BIAS
VIO
10 …F
10 …F
100 k
100 k
LS3
IN_LS3
IN_LDO1
LDO1
SCL
SDA
100 k
VIO
100 k
VIO
4.7 …F
47 …F
1.5 µH
L1
1.5 µH
100 nF
L4B
IN_DCDC1
VIO
100 k
22 …F
PGOOD_BU
PB
IN_BIAS
10 µH
TPS65218
IN_DCDC2
4.7 …F
1 …F
SYS_BU
IN_DCDC3
10 …F
±
10
10 …F
4.7 …F
4.7 …F
Copyright © 2017, Texas Instruments Incorporated
Figure 1-1. Simplified Schematic
2
Device Overview
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Table of Contents
1
Device Overview ......................................... 1
1.1
Features .............................................. 1
1.2
Applications ........................................... 1
1.3
Description ............................................ 1
1.4
Simplified Schematic ................................. 2
2
3
Revision History ......................................... 3
Pin Configuration and Functions ..................... 6
4
Specifications
3.1
5
Pin Functions ......................................... 6
............................................
Absolute Maximum Ratings .......................... 8
4.2
ESD Ratings .......................................... 8
4.3
Recommended Operating Conditions ................ 9
4.4
Thermal Information .................................. 9
4.5
Electrical Characteristics ............................ 10
4.6
Timing Requirements
4.7
Typical Characteristics .............................. 20
19
Detailed Description ................................... 21
5.1
5.2
............................................
Functional Block Diagram ...........................
Overview
7
8
8
4.1
...............................
6
21
22
9
.................................
...........................
5.5
Register Maps .......................................
Application and Implementation ....................
6.1
Application Information ..............................
6.2
Typical Application ..................................
Power Supply Recommendations ..................
Layout ....................................................
8.1
Layout Guidelines ...................................
8.2
Layout Example .....................................
Device and Documentation Support ...............
9.1
Device Support ......................................
9.2
Documentation Support .............................
9.3
Receiving Notification of Documentation Updates ..
9.4
Community Resources ..............................
9.5
Trademarks..........................................
9.6
Electrostatic Discharge Caution .....................
9.7
Glossary .............................................
5.3
Feature Description
23
5.4
Device Functional Modes
46
48
90
90
92
96
96
96
96
98
98
98
98
98
98
99
99
10 Mechanical, Packaging, and Orderable
Information .............................................. 99
2 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (August 2017) to Revision D
•
Page
Added the Not Recommended for New Designs statement o the data sheet ................................................ 1
Changes from Revision B (February 2016) to Revision C
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Page
Changed adjustable output voltage range to show separate values for DCDC1, DCDC2, and DCDC3 in
Features section ...................................................................................................................... 1
Changed DCDC4 default from 1.0 A : to 1.6 A in Features section ........................................................... 1
Changed DCDC4 adjustable output voltage minimum from 0.85 V : to 1.175 V in Features section ..................... 1
Changed 5-V load switch VIN range minimum from 3.0 V : to 4 V in Features section ..................................... 1
Changed the Simplified Schematic ................................................................................................. 2
Added updates to Description column in the Pin Functions table .............................................................. 6
Changed input voltage for LS1 max value from 3.3 V : to 3.6 V in the Recommended Operating Conditions section . 9
Changed the maximum value for the input voltage for LS3 parameter in the Recommended Operating
Conditions table ....................................................................................................................... 9
Added individual output voltage values for DCDC1, DCDC2, DCDC3, DCDC4 in the Recommended Operating
Conditions section .................................................................................................................... 9
Changed output voltage for DCDC5 from 1.0 V (MAX) and 1.1 V (MIN) : to 1 V (TYP) in the Recommended
Operating Conditions section........................................................................................................ 9
Changed output voltage for DCDC6 from 1.8 V (MAX) and 1.8 V (MIN) : to 1.8 V (TYP) in the Recommended
Operating Conditions section........................................................................................................ 9
Added additional voltage conditions on output current for DCDC4 in the Recommended Operating Conditions
section .................................................................................................................................. 9
Changed output current for DCDC5, DCDC6 max value from 10 mA : to 25 mA in the Recommended Operating
Conditions section .................................................................................................................... 9
Changed output current max value for LS2 from 1000 mA : to 920 mA in the Recommended Operating
Conditions section .................................................................................................................... 9
Added voltage conditions to output current for LS3 in the Recommended Operating Conditions section ................ 9
Deleted Note 2 in the Electrical Characteristics section ....................................................................... 10
Revision History
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
3
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
www.ti.com
Added SYS_BU subsection in the Electrical Characteristics section.........................................................
Changed first parameter of the INT_LDO subsection from VOUT : to VINT_LDO in the Electrical Characteristics
section ................................................................................................................................
Added additional test conditions to tHOLD in the Electrical Characteristics section ..........................................
Added typ value to INT_LDO COUT in the Electrical Characteristics section ................................................
Changed output voltage range max value for VDCDC1,2 from 1.65 V : to 1.675 V in the Electrical Characteristics
section ................................................................................................................................
Changed test condition for DCDC1, DCDC2 (1.1-V BUCK) and DCDC3 (1.2-V BUCK) IOUT from < 2.8 V : to <
2.7 V in the Electrical Characteristics section ...................................................................................
Changed power-good threshold, VOUT falling values for DCDC1, DCDC2 (1.1-V BUCK) VPG from 96% MIN and
97% MAX : to 95.9% MIN and 97.1% MAX in the Electrical Characteristics section ......................................
Added STRICT = 1 test condition for all VOV parameters in the Electrical Characteristics section .......................
Changed overvoltage detection threshold for DCDC1, DCDC2 (1.1-V BUCK) VOV from 103% MIN and 104%
MAX : to 102.9% MIN and 104.1% MAX in the Electrical Characteristics section .........................................
Deleted tolerance for all COUT except INT_LDO COUT in the Electrical Characteristics section ...........................
Added min and typ values for DCDC1, DCDC2 (1.1-V BUCK) COUT in the Electrical Characteristics section .........
Changed max value for DCDC1, DCDC2 (1.1-V BUCK) COUT from 500 µF : to 100 µF in the Electrical
Characteristics section..............................................................................................................
Added additional test condition to DCDC3 (1.2-V BUCK) DC accuracy in the Electrical Characteristics section ......
Added typ value for DCDC3 (1.2-V BUCK) COUT in the Electrical Characteristics section ................................
Added additional test condition to VDCDC4 output voltage ripple in the Electrical Characteristics section................
Changed power-good threshold, VOUT falling values for DCDC4 (3.3-V BUCK-BOOST) VPG from 96% MIN and
97% MAX : to 95.9% MIN and 97.1% MAX in the Electrical Characteristics section ......................................
Changed overvoltage detection threshold for DCDC4 (3.3-V BUCK-BOOST) VOV from 104% MIN and 105%
MAX : to 103.9% MIN and 105.1% MAX in the Electrical Characteristics section .........................................
Added typ value for DCDC4 (3.3-V BUCK-BOOST) COUT in the Electrical Characteristics section ......................
Deleted VCC voltage range test conditions from VIN_BU in the Electrical Characteristics section ..........................
Added additional test condition to tRISE in the Electrical Characteristics section ............................................
Added QINRUSH to the DCDC5, 6 POWER PATH in the Electrical Characteristics section ................................
Changed DC accuracy values for VDCDC5 from –1.5% (MIN) and 1.5% (MAX) : to –2% (MIN) and 4% (MAX) ........
Added and updated test conditions for VDCDC5 DC accuracy in the Electrical Characteristics section ...................
Changed operators in test conditions for DCDC5 (1-V BATTERY BACKUP SUPPLY) and DCDC6 (1.8-V
BATTERY BACKUP SUPPLY) IOUT from < : to ≤ in the Electrical Characteristics section ................................
Deleted IINRUSH from DCDC5 (1.0-V BATTERY BACKUP SUPPLY) and DCDC6 (1.8-V BATTERY BACKUP
SUPPLY) in the Electrical Characteristics section ..............................................................................
Changed DC accuracy values for VDCDC6 from –1.5% and 1.5% : to –2% and 2% in the Electrical Characteristics
section ................................................................................................................................
Changed DC accuracy min value for VDCDC6 from –10% : to –5% in the Electrical Characteristics section ............
Added test conditions for IOUT when device is on IN_BU in the Electrical Characteristics section .......................
Changed short circuit limit min value for LDO1 (1.8-V LDO) ILIMIT from 490 mA : to 445 mA in the Electrical
Characteristics section..............................................................................................................
Added test condition to all RDIS internal discharge resistor at output parameters in the Electrical Characteristics
section ................................................................................................................................
Changed operator in test conditions for LOAD SWITCH 2 (LS2) ILIMIT from < : to ≤ in the Electrical
Characteristics section..............................................................................................................
Changed min value for ILIMIT, LS2ILIM[1:0] = 00 from 100 mA : to 94 mA in the Electrical Characteristics section ...
Changed min value for ILIMIT, LS2ILIM[1:0] = 10 from 200 mA : to 188 mA in the Electrical Characteristics section ..
Changed min value for ILIMIT, LS2ILIM[1:0] = 01 from 500 mA : to 465 mA in the Electrical Characteristics section ..
Changed min value for ILIMIT, LS2ILIM[1:0] = 11 from 1000 mA : to 922 mA in the Electrical Characteristics section
Changed min value for ILIMIT, VIN_LS3 > 2.3 V, LS3ILIM[1:0] = 00 from 100 mA : to 98 mA in the Electrical
Characteristics section..............................................................................................................
Changed min value for ILIMIT, VIN_LS3 > 2.3 V, LS3ILIM[1:0] = 10 from 200 mA : to 194 mA in the Electrical
Characteristics section..............................................................................................................
Changed min value for ILIMIT, VIN_LS3 > 2.3 V, LS3ILIM[1:0] = 01 from 500 mA : to 475 mA in the Electrical
Characteristics section..............................................................................................................
Changed min value for ILIMIT, VIN_LS3 > 2.3 V, LS3ILIM[1:0] = 11 from 950 mA : to 900 mA in the Electrical
Characteristics section..............................................................................................................
Changed min value for ILIMIT, VIN_LS3 ≤ 2.3 V, LS3ILIM[1:0] = 00 from 100 mA : to 98 mA in the Electrical
Characteristics section..............................................................................................................
Changed min value for ILIMIT, VIN_LS3 ≤ 2.3 V, LS3ILIM[1:0] = 10 from 200 mA : to 194 mA in the Electrical
Revision History
10
10
10
10
10
10
11
11
11
11
11
11
12
12
12
13
13
13
13
13
13
14
14
14
14
14
14
14
15
15
16
16
16
16
16
17
17
17
17
17
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Characteristics section..............................................................................................................
Changed min value for ILIMIT, VIN_LS3 ≤ 2.3 V, LS3ILIM[1:0] = 01 from 500 mA : to 475 mA in the Electrical
Characteristics section..............................................................................................................
Changed high level output voltage, PGOOD_BU min value in VOH from (VDD_1 8 – 10 mV): to (VDCDC6 – 10 mV)
in the Electrical Characteristics section ..........................................................................................
Changed test condition in VOH from GPO2_CNF : to GPO2_BUF in the Electrical Characteristics section ............
Added test conditions to VOL for nPFO in the Electrical Characteristics section ............................................
Added new Note 2 in the Electrical Characteristics section ...................................................................
Added updates to Overview section ..............................................................................................
Changed the Functional Block Diagram..........................................................................................
Added updates to Power-Up Sequencing section ..............................................................................
Added updates to Power-Down Sequencing section ...........................................................................
Added updates to Supply Voltage Supervisor and Power Good (PGOOD) section ........................................
Added updates and changes to Internal LDO (INT_LDO) section ............................................................
Added updates and changes to Current Limited Load Switches section ....................................................
Changed Typical Application of Load Switch 2 figure in the Load Switch 2 (LS2) section ................................
Added updates to Load Switch 3 (LS3) section .................................................................................
Added updates and changes to UVLO section ..................................................................................
Added updates to Battery-Backup Supply Power-Path section ...............................................................
Added updates to Push Button Input (PB) section..............................................................................
Added updates to AC_DET Input (AC_DET) section ...........................................................................
Changed Modes of Operation Diagram in Device Functional Modes section ...............................................
Changed description for Bit 5 in the STATUS Register Field Descriptions table ...........................................
Added updates to the CONFIG2 Register Field Descriptions table ..........................................................
Changed description for Bits 2-0 in the SLEW Register Field Descriptions table ..........................................
Added updates to Layout section .................................................................................................
Added Receiving Notification of Documentation Updates section to Device and Documentation Support section ....
Added the Documentation Support section .....................................................................................
Changed the Electrostatic Discharge Caution statement ......................................................................
Changes from Revision A (September 2015) to Revision B
•
•
17
18
18
18
19
21
22
23
25
27
29
30
31
31
32
35
40
42
46
55
62
76
96
98
98
98
Page
Updated description for PGOOD to clarify that the output can be configured as open drain ............................... 6
Added VIN_LS3 conditions to ILIMIT for Load Switch 3 and updated the values ............................................... 17
Changes from Original (November 2014) to Revision A
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
17
Page
Added part number TPS65218B101 .............................................................................................. 1
Increased VIN range for low voltage load switch with 350-mA current limit .................................................. 1
Moved Tstg to the Absolute Maximum Ratings table and updated Handling Ratings table to an ESD Ratings table ... 8
Added device part number to Thermal Information table ........................................................................ 9
Added test conditions and values for VUVLO hysteresis......................................................................... 10
Changed test conditions for input voltage ranges from "VIN_BIAS > 2.7 V" to "VIN_BIAS > VUVLO" .......................... 10
Updated values for DCDC1-4 VOUT falling and rising ........................................................................... 11
Added more test conditions and values for VIN_DCDC4 .......................................................................... 12
Updated VDCDC4 test conditions and values and added output voltage ripple specification for PFM mode ............ 12
Updated test conditions and added new values for VDCDC5, VDCDC6 DC accuracy .......................................... 14
Updated VIN_LS1 max value and added additional test condition for RDS(ON) ................................................ 15
Added note for tHIGH ................................................................................................................ 19
Updated and added a note ........................................................................................................ 44
Added note to Application and Implementation ................................................................................ 90
Added Community Resources .................................................................................................... 98
Revision History
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
5
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
3 Pin Configuration and Functions
IN_DCDC2
L2
FB2
nWAKEUP
FB3
L3
IN_DCDC3
42
41
40
39
38
37
IN_DCDC3
37
PB
L3
38
43
FB3
39
nINT
nWAKEUP
40
44
FB2
41
PWR_EN
L2
42
45
IN_DCDC2
43
INT_LDO
FB1
PB
44
IN_BIAS
35
46
nINT
45
36
2
L1
PWR_EN
46
1
SDA
47
FB1
47
IN_DCDC1
48
L1
48
Figure 3-1 shows the 48-pin RSL Plastic Quad Flatpack No-Lead. Figure 3-2 shows the 48-pin PHP
PowerPAD™ Plastic Quad Flatpack.
IN_DCDC1
1
36
IN_BIAS
SDA
2
35
INT_LDO
SCL
3
34
GPO2
LDO1
4
33
LS2
SCL
3
34
GPO2
LDO1
4
33
LS2
IN_LDO1
5
32
IN_LS2
IN_LDO1
5
32
IN_LS2
IN_LS3
6
31
IN_LS1
IN_LS3
6
31
IN_LS1
LS3
7
30
LS1
LS3
7
30
LS1
PGOOD
8
29
N/C
PGOOD
8
29
N/C
AC_DET
9
28
N/C
AC_DET
9
28
N/C
nPFO
10
27
IN_BU
nPFO
10
27
IN_BU
GPIO1
11
26
GPIO3
GPIO1
11
26
GPIO3
IN_DCDC4
12
25
CC
IN_DCDC4
12
25
CC
3.1
24
SYS_BU
23
L6
22
FB6
21
FB5
20
L5
L4A
19
24
SYS_BU
PGOOD_BU
23
L6
18
22
FB6
IN_nCC
21
FB5
17
20
L5
DC34_SEL
19
PGOOD_BU
16
18
IN_nCC
PFI
17
DC34_SEL
Figure 3-1. 48-Pin RSL VQFN With Exposed
Thermal Pad
(Top View, 6 mm × 6 mm × 1 mm With 0.4-mm
Pitch)
15
16
PFI
Not to scale
DCDC4
15
DCDC4
Pad
14
14
L4B
Thermal
13
13
L4A
Pad
L4B
Thermal
Not to scale
Figure 3-2. 48-Pin PHP PowerPAD™ HTQFP
(Top View, 7 mm × 7 mm × 1 mm With 0.5-mm
Pitch)
Pin Functions
Pin Functions
PIN
NO.
NAME
TYPE
DESCRIPTION
1
IN_DCDC1
P
2
SDA
I/O
3
SCL
I
Clock input for the I2C interface. Connect to pullup resistor.
4
LDO1
O
Output voltage pin for LDO1. Connect to capacitor.
5
IN_LDO1
P
Input supply pin for LDO1.
6
IN_LS3
P
Input supply pin for load switch 3.
7
LS3
O
Output voltage pin for load switch 3. Connect to capacitor.
8
PGOOD
O
Power-good output (configured as open drain).
Pulled low when either DCDC1-4 or LDO1 are out of regulation. Load switches and DCDC5-6 do not affect
PGOOD pin.
9
AC_DET
I
AC monitor input and enable for DCDC1-4, LDO1 and load switches. See Section 5.4.1 for details. Tie pin to
IN_BIAS if not used.
10
nPFO
O
Power-fail comparator output, deglitched (open drain). Pin is pulled low when PFI input is below power-fail
threshold.
11
GPIO1
I/O
Pin configured as DDR reset-input (driving GPO2) or as general-purpose, open-drain output. See
Section 5.3.1.14 for more information.
12
IN_DCDC4
P
Input supply pin for DCDC4.
13
L4A
P
Switch pin for DCDC4. Connect to inductor.
14
L4B
P
Switch pin for DCDC4. Connect to inductor.
6
Input supply pin for DCDC1.
Data line for the I2C interface. Connect to pullup resistor.
Pin Configuration and Functions
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Pin Functions (continued)
PIN
TYPE
DESCRIPTION
NO.
NAME
15
DCDC4
P
Output voltage pin for DCDC4. Connect to capacitor.
16
PFI
I
Power-fail comparator input. Connect to resistor divider.
17
DC34_SEL
I
Power-up default selection pin for DCDC3 or DCDC4. Power-up default is programmed by a resistor
connected to ground. See Section 5.3.1.13 for resistor options.
18
IN_nCC
O
Output pin indicates if DCDC5 and DCDC6 are powered from main supply (IN_BU) or coin-cell battery (CC).
Pin is push-pull output. Pulled low when PMIC is powered from coin cell battery. Pulled high when PMIC is
powered from main supply (IN_BU).
19
PGOOD_BU
O
Power-good, push-pull output for DCDC5 and DCDC6. Pulled low when either DCDC5 or DCDC6 is out of
regulation. Pulled high (to DCDC6 output voltage) when both rails are in regulation.
20
L5
P
Switch pin for DCDC5. Connect to inductor.
21
FB5
I
Feedback voltage pin for DCDC5. Connect to output capacitor.
22
FB6
I
Feedback voltage pin for DCDC6. Connect to output capacitor.
23
L6
P
Switch pin for DCDC6. Connect to inductor.
24
SYS_BU
P
System voltage pin for battery-backup supply power path. Connect to 1-µF capacitor. Connecting any
external load to this pin is not recommended.
25
CC
P
Coin cell battery input. Serves as the supply to DCDC5 and DCDC6 if no voltage is applied to IN_BU. Tie this
pin to ground if it is not in use.
26
GPIO3
I/O
27
IN_BU
P
Default input supply pin for battery backup supplies (DCDC5 and DCDC6).
28
N/C
29
N/C
—
No connect. Leave pin floating.
Pin can be configured as warm reset (negative edge) for DCDC1/2 or as a general-purpose, open-drain
output. See Section 5.3.1.14 for more details.
30
LS1
O
Output voltage pin for load switch 1. Connect to capacitor.
31
IN_LS1
P
Input supply pin for load switch 1.
32
IN_LS2
P
Input supply pin for load switch 2.
33
LS2
O
Output voltage pin for load switch 2. Connect to capacitor.
34
GPO2
O
Pin configured as DDR reset signal (controlled by GPIO1) or as general-purpose output. Buffer can be
configured as push-pull or open-drain.
35
INT_LDO
P
Internal bias voltage. Connecting any external load to this pin is not recommended.
36
IN_BIAS
P
Input supply pin for reference system.
37
IN_DCDC3
P
Input supply pin for DCDC3.
38
L3
P
Switch pin for DCDC3. Connect to inductor.
39
FB3
I
Feedback voltage pin for DCDC3. Connect to output capacitor.
40
nWAKEUP
O
Signal to SOC to indicate a power on event (active low, open-drain output).
41
FB2
I
Feedback voltage pin for DCDC2. Connect to output capacitor.
42
L2
P
Switch pin for DCDC2. Connect to inductor.
43
IN_DCDC2
P
Input supply pin for DCDC2.
44
PB
I
Push-button monitor input. Typically connected to a momentary switch to ground (active low). See
Section 5.4.1 for details.
45
nINT
O
Interrupt output (active low, open drain). Pin is pulled low if an interrupt bit is set. The pin returns to Hi-Z state
after the bit causing the interrupt has been read. Interrupts can be masked.
46
PWR_EN
I
Power enable input for DCDC1-4, LDO1 and load switches. See Section 5.4.1 for details.
47
FB1
I
Feedback voltage pin for DCDC1. Connect to output capacitor.
48
L1
P
Switch pin for DCDC1. Connect to inductor.
—
Thermal Pad
P
Power ground and thermal relief. Connect to ground plane.
Pin Configuration and Functions
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
7
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
4 Specifications
4.1
Absolute Maximum Ratings
Operating under free-air temperature range (unless otherwise noted) (1)
Supply voltage
Input voltage
Output voltage
MIN
MAX
IN_BIAS, IN_LDO1, IN_LS2, IN_DCDC1, IN_DCDC2,
IN_DCDC3, IN_DCDC4
–0.3
7
IN_LS1, CC
–0.3
3.6
IN_LS3
–0.3
11.2
IN_BU
–0.3
5.8
DC34_SEL
–0.3
3.6
All pins unless specified separately
–0.3
7
DC34_SEL
–0.3
3.6
All pins unless specified separately
–0.3
7
Source or sink
current
GPO2
6
PGOOD_BU, IN_nCC
1
Sink current
PGOOD, nWAKEUP, nINT, nPFO, SDA, GPIO1, GPIO3
UNIT
V
V
V
mA
6
mA
TA
Operating ambient temperature
–40
105
°C
TJ
Junction temperature
–40
125
°C
Tstg
Storage temperature
–65
150
°C
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
4.2
ESD Ratings
VALUE
V(ESD)
(1)
(2)
8
Electrostatic
discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
4.3
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Supply voltage, IN_BIAS
2.7
5.5
V
Input voltage for DCDC1, DCDC2, DCDC3, DCDC4
2.7
5.5
V
Supply voltage, IN_BU
2.2
5.5
V
Supply voltage, CC
2.2
3.3
V
Input voltage for LDO1
1.8
5.5
V
Input voltage for LS1
1.2
3.6
V
Input voltage for LS2
3
5.5
V
Input voltage for LS3
1.8
10
V
Output voltage for DCDC1
0.85
1.675
V
Output voltage for DCDC2
0.85
1.675
V
Output voltage for DCDC3
0.9
3.4
V
Output voltage for DCDC4
1.175
3.4
V
Output voltage for DCDC5
1
V
Output voltage for DCDC6
1.8
V
Output voltage for LDO1
Output current for DCDC1, DCDC2, DCDC3
Output current for DCDC4
0.9
3.4
V
0
1.8
A
VIN_DCDC4 = 2.8 V
1
VIN_DCDC4 = 3.6 V
1.3
VIN_DCDC4 = 5 V
1.6
A
Output current for DCDC5, DCDC6
0
25
mA
Output current for LDO1
0
400
mA
Output current for LS1
0
300
mA
Output current for LS2
0
920
mA
VIN_LS3 > 2.3 V
0
900
VIN_LS3 ≤ 2.3 V
0
475
Output current for LS3
4.4
mA
Thermal Information
TPS65218
THERMAL METRIC
(1)
RSL (VQFN)
PHP (HTQFP)
16 PINS
16 PINS
UNIT
RθJC(top)
Junction-to-case (top)
17.2
13.3
°C/W
RθJB
Junction-to-board
5.8
7.9
°C/W
RθJA
Thermal resistance, junction to ambient. JEDEC 4-layer, high-K board.
30.6
26.7
°C/W
ΨJT
Junction-to-package top
0.2
0.3
°C/W
ΨJB
Junction-to-board
5.6
7.8
°C/W
Junction-to-case (bottom)
1.5
0.7
°C/W
RθJC(bot)
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
9
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
4.5
www.ti.com
Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
INPUT VOLTAGE AND CURRENTS
VIN_BIAS
VUVLO
Input supply voltage range
Undervoltage lockout
VUVLO
Normal operation
2.7
5.5
EEPROM programming
4.5
5.5
Supply falling; measured in
respect to VIN_BIAS
UVLO[1:0] = 00b
2.7
2.75
2.8
V
UVLO[1:0] = 01b
2.85
2.95
3.05
V
UVLO[1:0] = 10b
3.15
3.25
3.35
V
UVLO[1:0] = 11b
3.25
3.35
3.45
V
Supply rising; VIN_BIAS slew
rate < 30 V/s
UVLOHYS = 0b
Supply rising; VIN_BIAS slew
rate > 30 V/s
Hysteresis
V
(1)
200
mV
400
mV
UVLOHYS = 0b (1)
0
mV
UVLOHYS = 1b
0
mV
5
ms
5
µA
220
µA
UVLOHYS = 1b
Deglitch time
IOFF
OFF state current, total current
into IN_BIAS, IN_DCDCx,
IN_LDO1, IN_LSx, IN_BU
VIN = 3.6 V; All rails disabled.
TJ = 0°C to 85°C
ISUSPEND
SUSPEND current, total current
into IN_BIAS, IN_DCDCx,
IN_LDO1, IN_LSx, IN_BU
VIN = 3.6 V; DCDC3 enabled, low-power mode, no
load.
All other rails disabled.
TJ = 0°C to 105°C
VSYS_BU
SYS_BU voltage range
Powered from VIN_BU or VCC
CSYS_BU
Recommended SYS_BU
capacitor
Ceramic, X5R or X7R, see Table 6-3
Tolerance
Ceramic, X5R or X7R, rated voltage ≥ 6.3 V
SYS_BU
2.2
5.5
1
–20%
V
µF
20%
INT_LDO
VINT_LDO
Output voltage
2.5
DC accuracy
IOUT < 10 mA
IOUT
Output current range
Maximum allowable external load
ILIMIT
Short circuit current limit
Output shorted to GND
Hold-up time
Measured from VINT_LDO = 2.5 V to VINT_LDO = 1.8 V
All rails enabled before power off,
VIN_BIAS = 2.8 V to 0 V in < 1 µs
No external load on INT_LDO
CINT_LDO = 22 µF, see Table 6-3
150
Nominal output capacitor value
Ceramic, X5R or X7R, see Table 6-3
0.1
Tolerance
Ceramic, X5R or X7R, rated voltage ≥ 6.3 V
tHOLD
COUT
V
–2%
2%
0
10
23
mA
mA
ms
1
–20%
22
µF
20%
DCDC1 (1.1-V BUCK)
VIN_DCDC1
VDCDC1
IOUT
IQ
RDS(ON)
ILIMIT
(1)
10
Input voltage range
VIN_BIAS > VUVLO
2.7
5.5
V
Output voltage range
Adjustable through I2C
0.85
1.675
V
DC accuracy
2.7 V ≤ VIN ≤ 5.5 V; 0 A ≤ IOUT ≤ 1.8 A
–2%
2%
Continuous output current
VIN_DCDC1 > 2.7 V
Quiescent current
Total current from IN_DCDC1 pin; Device not
switching, no load
High-side FET on resistance
Low-side FET on resistance
1.8
A
25
50
µA
VIN_DCDC1 = 3.6 V
230
355
VIN_DCDC1 = 3.6 V
90
145
High-side current limit
VIN_DCDC1 = 3.6 V
2.8
Low-side current limit
VIN_DCDC1 = 3.6 V
3.1
mΩ
A
200-mV hysteresis option is available for the TPS65218B101 device option.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Power-good threshold
VOUT falling
Hysteresis
VOUT rising
VPG
VOUT falling
Deglitch
VOUT rising
MIN
TYP
STRICT = 0b
88.5%
90%
91.5%
STRICT = 1b
95.9%
96.5%
97.1%
STRICT = 0b
3.8%
4.1%
4.4%
STRICT = 1b
0.25%
STRICT = 0b
1
ms
STRICT = 1b
50
µs
STRICT = 0b
10
µs
STRICT = 1b
10
µs
5
ms
Time-out
Overvoltage detection threshold
VOUT rising, STRICT = 1b
Hysteresis
VOUT falling, STRICT = 1b
0.25%
Deglitch
VOUT rising, STRICT = 1b
50
IINRUSH
Inrush current
VIN_DCDC1 = 3.6 V; COUT = 10 µF to 100 µF
RDIS
Discharge resistor
VOV
Nominal inductor value
L
102.9%
See Table 6-2
Tolerance
COUT
Output capacitance value
MAX UNIT
103.5%
104.1%
µs
500
mA
150
250
350
Ω
1
1.5
2.2
µH
22
100 (2)
µF
–30%
30%
Ceramic, X5R or X7R, see Table 6-3
10
VIN_BIAS > VUVLO
2.7
5.5
V
V
DCDC2 (1.1-V BUCK)
VIN_DCDC2
Input voltage range
2
Output voltage range
Adjustable through I C
0.85
1.675
DC accuracy
2.7 V ≤ VIN ≤ 5.5 V; 0 A ≤ IOUT ≤ 1.8 A
–2%
2%
IOUT
Continuous output current
VIN_DCDC2 > 2.7 V
IQ
Quiescent current
Total current from IN_DCDC2 pin; Device not
switching, no load
High-side FET on resistance
VDCDC2
RDS(ON)
ILIMIT
1.8
A
25
50
µA
VIN_DCDC2 = 3.6 V
230
355
Low-side FET on resistance
VIN_DCDC2 = 3.6 V
90
145
High-side current limit
VIN_DCDC2 = 3.6 V
2.8
Low-side current limit
VIN_DCDC2 = 3.6 V
3.1
Power-good threshold
VOUT falling
Hysteresis
VPG
VOUT rising
VOUT falling
Deglitch
VOUT rising
88.5%
90%
91.5%
STRICT = 1b
95.9%
96.5%
97.1%
STRICT = 0b
3.8%
4.1%
4.4%
0.25%
STRICT = 0b
1
ms
STRICT = 1b
50
µs
STRICT = 0b
10
µs
STRICT = 1b
10
µs
5
ms
Time-out
VOV
Overvoltage detection threshold
VOUT rising, STRICT = 1b
Hysteresis
VOUT falling, STRICT = 1b
0.25%
50
Deglitch
VOUT rising, STRICT = 1b
IINRUSH
Inrush current
VIN_DCDC2 = 3.6 V; COUT = 10 µF to 100 µF
RDIS
Discharge resistor
Nominal inductor value
L
See Table 6-2
Tolerance
COUT
Output capacitance value
A
STRICT = 0b
STRICT = 1b
mΩ
102.9%
103.5%
150
250
1
1.5
–30%
Ceramic, X5R or X7R, see Table 6-3
10
104.1%
µs
500
mA
350
Ω
2.2
µH
30%
22
100 (2)
µF
DCDC3 (1.2-V BUCK)
(2)
500-µF of remote capacitance can be supported for DCDC1/2.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
11
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
VIN_DCDC3
TEST CONDITIONS
MIN
TYP
MAX UNIT
Input voltage range
VIN_BIAS > VUVLO
2.7
5.5
V
Output voltage range
Adjustable through I2C
0.9
3.4
V
DC accuracy
2.7 V ≤ VIN ≤ 5.5 V; 0 A ≤ IOUT ≤ 1.8 A,
VIN_DCDC3 ≥ (VDCDC3 + 700 mV)
–2%
2%
IOUT
Continuous output current
VIN_DCDC3 > 2.7 V
IQ
Quiescent current
Total current from IN_DCDC3 pin;
Device not switching, no load
High-side FET on resistance
Low-side FET on resistance
VDCDC3
RDS(ON)
ILIMIT
1.8
A
25
50
µA
VIN_DCDC3 = 3.6 V
230
345
VIN_DCDC3 = 3.6 V
100
150
High-side current limit
VIN_DCDC3 = 3.6 V
2.8
Low-side current limit
VIN_DCDC3 = 3.6 V
3
Power-good threshold
VOUT falling
Hysteresis
VPG
STRICT = 0b
VOUT rising
VOUT falling
Deglitch
VOUT rising
90%
STRICT = 1b
95%
95.5%
96%
STRICT = 0b
3.8%
4.1%
4.4%
0.25%
STRICT = 0b
1
ms
STRICT = 1b
50
µs
STRICT = 0b
10
µs
STRICT = 1b
10
µs
5
VOUT rising, STRICT = 1b
104%
Hysteresis
VOUT falling, STRICT = 1b
0.25%
50
Deglitch
VOUT rising, STRICT = 1b
IINRUSH
Inrush current
VIN_DCDC3 = 3.6 V; COUT = 10 µF to 100 µF
RDIS
Discharge resistor
L
See Table 6-2
Tolerance
COUT
Output capacitance value
91.5%
STRICT = 1b
Overvoltage detection threshold
Nominal inductor value
A
88.5%
Time-out
VOV
mΩ
104.5%
µs
500
mA
150
250
350
Ω
1.0
1.5
2.2
µH
–30%
Ceramic, X5R or X7R, see Table 6-3
ms
105%
10
30%
22
100
µF
DCDC4 (3.3-V BUCK-BOOST) / ANALOG AND I/O
VIN_DCDC4
Input voltage soft-start range
Input voltage operating range
VDCDC4
VIN_BIAS > VUVLO, –40°C to +55°C
3.4
VIN_BIAS > VUVLO, 56°C to 105°C
3.8
VIN_BIAS > VUVLO, –40°C to +105°C
2.7
5.5
V
1.175
3.4
V
–2%
2%
2
Output voltage range
Adjustable through I C
DC accuracy
2.7 V ≤ VIN ≤ 5.5 V;
0 A ≤ IOUT ≤ 1 A
Output voltage ripple
PFM mode enabled;
4.2 V ≤ VIN ≤ 5.5 V;
0 A ≤ IOUT ≤ 1 A
COUT = 80 µF
VOUT = 3.3 V
V
200 mVpp
Minimum duty cycle in stepdown mode
IOUT
Continuous output current
IQ
Quiescent current
fSW
Switching frequency
12
18%
VIN_DCDC4 = 2.8 V, VOUT = 3.3 V
1
VIN_DCDC4 = 3.6 V, VOUT = 3.3 V
1.3
VIN_DCDC4 = 5 V, VOUT = 3.3 V
1.6
Total current from IN_DCDC4 pin; Device not
switching, no load
25
2400
Specifications
50
A
µA
kHz
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
High-side FET on resistance
VIN_DCDC3 = 3.6 V
Low-side FET on resistance
VIN_DCDC3 = 3.6 V
Average switch current limit
VIN_DCDC4 = 3.6 V
Power-good threshold
VOUT falling
RDS(ON)
ILIMIT
Hysteresis
VPG
VOUT rising
MIN
Deglitch
VOUT rising
L4B to DCDC4
149
L4A to GND
142
190
144
190
L4B to GND
3000
88.5%
90%
91.5%
STRICT = 1b
94.9%
95.5%
96.1%
STRICT = 0b
3.8%
4.1%
4.4%
0.25%
STRICT = 0b
1
ms
STRICT = 1b
50
µs
STRICT = 0b
10
µs
STRICT = 1b
10
µs
5
ms
Overvoltage detection threshold
VOUT rising, STRICT = 1b
Hysteresis
VOUT falling, STRICT = 1b
0.25%
Deglitch
VOUT rising, STRICT = 1b
50
IINRUSH
Inrush current
VIN_DCDC4 = 3.6 V; COUT = 10 µF to 100 µF
RDIS
Discharge resistor
Nominal inductor value
L
See Table 6-2
Tolerance
COUT
Output capacitance value
mΩ
mA
STRICT = 0b
Time-out
VOV
MAX UNIT
166
STRICT = 1b
VOUT falling
TYP
IN_DCDC4 to L4A
103.9%
104.5%
150
250
1.2
1.5
–30%
Ceramic, X5R or X7R, see Table 6-3
40
VIN_BU = 0 V
105.1%
µs
500
mA
350
Ω
2.2
µH
30%
80
100
µF
2.2
3.3
V
2.2
5.5
V
DCDC5, DCDC6 POWER PATH
VCC
DCDC5, 6 input voltage range
VIN_BU
DCDC5, 6 input voltage range (3)
tRISE
VCC, VIN_BU rise time
VCC = 0 V to 3.3 V, VIN_BU = 0 V to 5.5 V
Power path switch impedance
CC to SYS_BU
VCC = 2.4 V, VIN_BU = 0 V
14.5
Power path switch impedance
IN_BU to SYS_BU
VIN_BU = 3.6 V
10.5
Forward leakage current
Into CC pin;
VCC = 3.3 V, VIN_BU = 0 V;
OFF state; FSEAL = 0b;
over full temperature range
Reverse leakage current
Out of CC pin;
VCC = 1.5 V; VIN_BU = 5.5 V;
over full temperature range
RCC
Acceptable CC source
impedance
IOUT,
IOUT,
IQ
Quiescent current
Average current into CC pin; RECOVERY or
POWER_OFF state; VIN_BU = 0 V; VCC = 2.4 V;
DCDC5 and DCDC6 enabled, no load TJ = 25°C
350
nA
QINRUSH
Inrush charge
VIN_BIAS = decaying; CC = 3 V; CSYS_BU = 1 µF;
SYS_BU = 2.5 V to 3 V; CCseries_resist = 10 Ω CCC =
4.7 µF
720
nC
RDS(ON)
ILEAK
DCDC5
DCDC6
30
µs
Ω
50
300
nA
500
< 10 µA;
< 10 µA
1000
Ω
DCDC5 (1-V BATTERY BACKUP SUPPLY)
(3)
IN_BU has priority over CC input.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
13
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
Output voltage
VDCDC5
DC accuracy
IOUT
TYP
ILIMIT
VPG
L
–2%
4%
2.2 V ≤ VCC ≤ 3.3 V;
IOUT ≥ 1 µA at –40°C ≤ TA ≤ 35°C
IOUT ≥ 4 µA at 35°C < TA ≤ 65°C
IOUT ≥ 7 µA at TA > 65°C
VIN_BIAS decay rate during CC transition > 150 V/s
–2%
4%
2.2 V ≤ VCC ≤ 3.3 V;
IOUT ≥ 1 µA at –40°C ≤ TA ≤ 35°C
IOUT ≥ 4 µA at 35°C < TA ≤ 65°C
IOUT ≥ 7 µA at TA > 65°C
VIN_BIAS decay rate during CC transition < 150 V/s
–10%
5%
Output voltage ripple
L = 10 µH; COUT = 22 µF; 100-µA load
Continuous output current
2.2 V ≤ VCC ≤ 3.3 V
VIN_BU = 0 V
32 (4) mVpp
10
100
µA
25
mA
High-side FET on resistance
VIN_BU = 2.8 V
2.5
3.5
Low-side FET on resistance
VIN_BU = 2.8 V
2
3
High-side current limit
VIN_BU = 2.8 V
Power-good threshold
VOUT falling
Hysteresis
VOUT rising
Nominal inductor value
Chip inductor, see Table 6-2
50
79%
Output capacitance value
85%
Ω
mA
91%
6%
4.7
Tolerance
COUT
V
2.7 V ≤ VIN_BU ≤ 5.5 V;
IOUT ≥ 1 µA at –40°C ≤ TA ≤ 35°C
IOUT ≥ 4 µA at 35°C < TA ≤ 65°C
IOUT ≥ 7 µA at TA > 65°C
2.7 V ≤ VIN_BU ≤ 5.5 V
RDS(ON)
MAX UNIT
1
Ceramic, X5R or X7R, see Table 6-3
Tolerance
10
22
–30%
30%
20 (5)
47
–20%
20%
µH
µF
DCDC6 (1.8-V BATTERY BACKUP SUPPLY)
VDCDC6
Output voltage
VDCDC6
DC accuracy
1.8
–2%
2%
2.2 V ≤ VCC ≤ 3.3 V;
1 µA ≤ IOUT ≤ 100 µA
VIN_BIAS decay rate during CC transition > 150 V/s
–2%
2%
2.2 V ≤ VCC ≤ 3.3 V;
1 µA ≤ IOUT ≤ 100 µA
VIN_BIAS decay rate during CC transition < 150 V/s
–5%
5%
VDCDC6
Output voltage ripple
L = 10 µH; COUT = 22 µF; 100-µA load
IOUT
Continuous output current
2.2 V ≤ VCC ≤ 3.3 V
VIN_BU = 0 V
30 (4) mVpp
10
2.7 V ≤ VIN_BU ≤ 5.5 V
RDS(ON)
ILIMIT
VPG
L
(4)
(5)
14
V
2.7 V ≤ VIN_BU ≤ 5.5 V;
1 µA ≤ IOUT ≤ 25 mA
100
µA
25
mA
High-side FET on resistance
VIN_BU = 3 V
2.5
3.5
Low-side FET on resistance
VIN_BU = 3 V
2
3
High-side current limit
VIN_BU = 3 V
50
Power-good threshold
VOUT falling
Hysteresis
VOUT rising
Nominal inductor value
Chip inductor, see Table 6-2
Tolerance
87%
91%
Ω
mA
95%
3%
4.7
–30%
10
22
µH
30%
For PHP package: 160mVpp at -40°C, and 120mVpp from 25°C to 105°C.
For PHP package: 40µF.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
COUT
Output capacitance value
TEST CONDITIONS
MIN
Ceramic, X5R or X7R, see Table 6-3
20 (5)
47
–20%
20%
Tolerance
TYP
MAX UNIT
µF
LDO1 (1.8-V LDO)
VIN_LDO1
Input voltage range
VIN_BIAS > VUVLO
IQ
Quiescent current
No load
Output voltage range
Adjustable through I2C
DC accuracy
VOUT + 0.2 V ≤ VIN ≤ 5.5 V; 0 A ≤ IOUT ≤ 200 mA
VOUT
3.4
2%
VIN_LDO1 – VDO = VOUT
0
200
VIN_LDO1 > 2.7 V, VOUT = 1.8 V
0
400
ILIMIT
Short circuit current limit
Output shorted to GND
VDO
Dropout voltage
IOUT = 100 mA, VIN = 3.6 V
VOUT falling
Power-good threshold
Hysteresis, VOUT rising
VOUT falling
Deglitch
VOUT rising
445
550
V
mA
mA
200
STRICT = 0b
86%
90%
94%
STRICT = 1b
95%
95.5%
96%
STRICT = 0b
3%
4%
5%
STRICT = 1b
V
µA
0.9
Output current range
mV
0.25%
STRICT = 0b
1
ms
STRICT = 1b
50
µs
STRICT = 0b
10
µs
STRICT = 1b
10
µs
Time-out
VOV
5.5
35
–2%
IOUT
VPG
1.8
5
VOUT rising, STRICT = 1b
Hysteresis
VOUT falling, STRICT = 1b
0.25%
VOUT rising, STRICT = 1b
50
µs
VOUT falling, STRICT = 1b
1
ms
Deglitch
RDIS
Discharge resistor
COUT
Nominal output capacitance
value
104%
150
104.5%
ms
Overvoltage detection threshold
250
105%
350
Ω
Ceramic, X5R or X7R
10
100
µF
VIN_BIAS > VUVLO
1.2
3.6
V
LOAD SWITCH 1 (LS1)
VIN_LS1
RDS(ON)
Input voltage range
Static on resistance
VIN_LS1 = 3.3 V, IOUT = 300 mA, over full
temperature range
110
VIN_LS1 = 1.8 V, IOUT = 300 mA,
DDR2, LPDDR, MDDR at 266 MHz over full
temperature range
110
VIN_LS1 = 1.5 V, IOUT = 300 mA,
DDR3 at 333 MHz over full temperature range
110
VIN_LS1 = 1.35 V, IOUT = 300 mA,
DDR3L at 333 MHz over full temperature range
110
VIN_LS1 = 1.2 V, IOUT = 200 mA,
LPDDR2 at 333 MHz over full temperature range
150
ILIMIT
Short circuit current limit
Output shorted to GND
tBLANK
Interrupt blanking time
Output shorted to GND until interrupt is triggered
RDIS
Internal discharge resistor at
output (6)
LS1DCHRG = 1
TOTS
(6)
(7)
Overtemperature shutdown (7)
Hysteresis
350
mΩ
mA
15
ms
150
250
350
125
132
139
10
Ω
°C
Discharge function disabled by default.
Switch is temporarily turned OFF if temperature exceeds OTS threshold.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
15
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
Nominal output capacitance
value
COUT
TEST CONDITIONS
MIN
Ceramic, X5R or X7R, see Table 6-3
10
TYP
MAX UNIT
100
µF
5.5
V
2.7
V
LOAD SWITCH 2 (LS2)
VIN_LS2
VUVLO
RDS(ON)
ILIMIT
Input voltage range
VIN_BIAS > VUVLO
Undervoltage lockout
Measured at IN_LS2. Supply falling (8)
Hysteresis
Input voltage rising
Static on resistance
VIN_LS2 = 5 V, IOUT = 500 mA, over full temperature
range
Short circuit current limit
Output shorted to GND;
VIN_LS2 ≥ 4 V
4
2.48
2.6
170
500
LS2ILIM[1:0] = 00b
94
126
LS2ILIM[1:0] = 01b
188
251
LS2ILIM[1:0] = 10b
465
631
LS2ILIM[1:0] = 11b
922
1290
ILEAK
Reverse leakage current
VLS2 > VIN_LS2 + 1 V
12
tBLANK
Interrupt blanking time
Output shorted to GND until interrupt is triggered
15
RDIS
Internal discharge resistor at
output (6)
LS2DCHRG = 1b
TOTS
COUT
(8)
16
Overtemperature shutdown (8)
30
250
380
125
132
139
10
Ceramic, X5R or X7R, see Table 6-3
1
mΩ
mA
µA
ms
150
Hysteresis
Nominal output capacitance
value
mV
100
Ω
°C
µF
Switch is temporarily turned OFF if input voltage drops below UVLO threshold.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
LOAD SWITCH 3 (LS3)
VIN_LS3
RDS(ON)
Input voltage range
Static on resistance
VIN_BIAS > VUVLO
440
VIN_LS3 = 5 V, IOUT= 500 mA, over full temperature
range
526
VIN_LS3 = 2.8 V, IOUT= 200 mA, over full temperature
range
656
VIN_LS3 = 1.8 V, IOUT= 200 mA, over full temperature
range
910
Short circuit current limit
VIN_LS3 ≤ 2.3 V,
Output shorted to GND
98
126
LS3ILIM[1:0] = 01b
194
253
LS3ILIM[1:0] = 10b
475
738
LS3ILIM[1:0] = 11b
900
1234
LS3ILIM[1:0] = 00b
98
126
LS3ILIM[1:0] = 01b
194
253
LS3ILIM[1:0] = 10b
475
Interrupt blanking time
Output shorted to GND until interrupt is triggered
RDIS
Internal discharge resistor at
output (6)
LS3DCHRG = 1
COUT
Overtemperature shutdown (8)
ms
650
1000
1500
Ω
125
132
139
°C
10
Ceramic, X5R or X7R, see Table 6-3
mA
738
15
Hysteresis
Nominal output capacitance
value
V
mΩ
LS3ILIM[1:0] = 00b
tBLANK
TOTS
10
VIN_LS3 = 9 V, IOUT= 500 mA, over full temperature
range
VIN_LS3 > 2.3 V,
Output shorted to GND
ILIMIT
1.8
1
100
°C
220
µF
BACKUP BATTERY MONITOR
VTH
Comparator threshold
Ideal level
3
V
Good level
2.6
V
Low level
2.3
Accuracy
–3%
RLOAD
Load impedance
Applied from CC to GND during comparison
tDLY
Measurement delay
RLOAD is connected during delay time. Measurement
is taken at the end of delay.
70
V
3%
100
130
600
kΩ
ms
I/O LEVELS AND TIMING CHARACTERISTICS
PGDLY
PGOOD delay time
PGDLY[1:0] = 00b
10
PGDLY[1:0] = 01b
20
PGDLY[1:0] = 10b
50
PGDLY[1:0] = 11b
PB input
AC_DET input
tDG
Deglitch time
PWR_EN input
GPIO1
GPIO3
ms
150
Rising edge
100
ms
Falling edge
50
ms
Rising edge
100
µs
Falling edge
10
ms
Rising edge
10
ms
Falling edge
100
µs
Rising edge
1
ms
Falling edge
1
ms
Rising edge
5
µs
Falling edge
5
µs
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
17
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
tRESET
Reset time
TEST CONDITIONS
PB input held low
MIN
8
TRST = 1b
15
SCL, SDA, GPIO1, GPIO3
VIH
High level input voltage
VIL
Low level input voltage
Low level output voltage
VPFI
AC_DET, PB
VDC34_SEL
RDC34_SEL
IBIAS
ILEAK
0
0.4
GPO2; ISOURCE = 5 mA; GPO2_BUF = 1
VIN_LS1 –
0.3
VIN_LS1
PGOOD_BU; ISOURCE = 100 µA
VDCDC6 –
10 mV
0
0.3
nPFO; ISINK = 2 mA
0
0.35
PGOOD_BU; ISINK = 100 µA
0
Input falling
Hysteresis
Input rising
DC34_SEL bias current
DCDC3 / DCDC4 power-up
default selection thresholds
DCDC3 / DCDC4 power-up
default selection resistor values
Input bias current
Pin leakage current
V
V
nWAKEUP, nINT, SDA, PGOOD, GPIO1, GPO2,
GPIO3; ISINK = 2 mA
V
0.3
800
mV
40
Accuracy
IDC34_SEL
V
1.3
SCL, SDA, PWR_EN, AC_DET, PB, GPIO1, GPIO3
Power-fail comparator threshold
Deglitch
s
1.3
High level output voltage
VOL
MAX UNIT
0.66 ×
IN_BIAS
PWR_EN
VOH
TYP
TRST = 0b
–4%
mV
4%
Input falling
25
µs
Input rising
10
ms
Enabled only at power-up
10
µA
Threshold 1
100
Threshold 2
163
Threshold 3
275
Threshold 4
400
Threshold 5
575
Threshold 6
825
Threshold 7
1200
mV
Setting 0
0
0
7.7
Setting 1
11.3
12.1
13
Setting 2
18.1
20
22
Setting 3
30.9
31.6
32.3
Setting 4
44.8
45.3
46.4
Setting 5
64.2
64.9
Setting 6
92.9
95.3
Setting 7
135.3
150
SCL, SDA, GPIO1 (9), GPIO3 (9); VIN = 3.3 V
0.01
kΩ
96.9
1
µA
PB, AC_DET, PFI; VIN = 3.3 V
500
nA
nINT, nWAKEUP, nPFO, PGOOD, PWR_EN,
GPIO1 (10), GPO2 (11), GPIO3 (10)
VOUT = 3.3 V
500
nA
OSCILLATOR
ƒOSC
Oscillator frequency
Frequency accuracy
2400
TJ = –40°C to +105°C
–12%
kHz
12%
(9) Configured as input.
(10) Configured as output.
(11) Configured as open-drain output.
18
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
135
145
MAX UNIT
OVERTEMPERATURE SHUTDOWN
TOTS
TWARN
4.6
Overtemperature shutdown
Increasing junction temperature
Hysteresis
Decreasing junction temperature
High-temperature warning
Increasing junction temperature
Hysteresis
Decreasing junction temperature
155
20
90
100
110
15
°C
Timing Requirements
MIN
Serial clock frequency
tHD;STA
Hold time (repeated) START condition. After this period, the
first clock pulse is generated.
LOW period of the SCL clock
tHIGH
HIGH period of the SCL clock
tSU;STA
Set-up time for a repeated START condition
Data hold time
tSU;DAT
Data set-up time
tr
Rise time of both SDA and SCL signals
tf
Fall time of both SDA and SCL signals
tSU;STO
Set-up time for STOP condition
MAX
UNIT
kHz
400
tLOW
tHD;DAT
NOM
100
fSCL
SCL = 100 kHz
4
µs
SCL = 400 kHz
600
ns
SCL = 100 kHz
4.7
SCL = 400 kHz
1.3
SCL = 100 kHz
4
SCL = 400 kHz (1)
1
µs
µs
SCL = 100 kHz
4.7
SCL = 400 kHz
600
µs
SCL = 100 kHz
0
3.45
µs
SCL = 400 kHz
0
900
ns
SCL = 100 kHz
250
SCL = 400 kHz
100
ns
ns
SCL = 100 kHz
1000
SCL = 400 kHz
300
SCL = 100 kHz
300
SCL = 400 kHz
300
ns
ns
SCL = 100 kHz
4
µs
SCL = 400 kHz
600
ns
SCL = 100 kHz
4.7
tBUF
Bus free time between STOP and START condition
SCL = 400 kHz
1.3
tSP
Pulse width of spikes which must be suppressed by the input SCL = 100 kHz
filter
SCL = 400 kHz
— (2)
— (2)
0
50
Cb
Capacitive load for each bus line
(1)
(2)
°C
µs
SCL = 100 kHz
400
SCL = 400 kHz
400
ns
pF
The SCL duty cycle at 400 kHz must be > 40%.
The inputs of I2C devices in Standard-mode do not require spike suppression.
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
19
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
4.7
www.ti.com
Typical Characteristics
0.3%
0.25%
0.2%
0.15%
0.1%
0.05%
0
-0.05%
-0.1%
-0.15%
-0.2%
-0.25%
-0.3%
-0.35%
-0.4%
VIN = 3.6 V
VIN = 5 V
Accuracy
Accuracy
at TJ = 25°C unless otherwise noted
0
0.2
0.4
0.6
0.8
1
1.2
Output Current (A)
1.4
1.6
0.15%
0.1%
0.05%
0
-0.05%
-0.1%
-0.15%
-0.2%
-0.25%
-0.3%
-0.35%
-0.4%
-0.45%
-0.5%
-0.55%
VIN = 3.6 V
VIN = 5 V
0
1.8
0.2
0.4
D001
VOUT = 1.1 V
1.8
D002
0.75%
VIN = 3.6 V
VIN = 5 V
0.05%
VIN = 3.6 V
VIN = 5 V
0.5%
0.25%
Accuracy
0
Accuracy
1.6
Figure 4-2. DCDC2 Accuracy
0.1%
-0.05%
-0.1%
-0.15%
0
-0.25%
-0.5%
-0.75%
-0.2%
-1%
-0.25%
-1.25%
0
0.2
0.4
0.6
0.8
1
1.2
Output Current (A)
1.4
1.6
1.8
0
0.2
0.4
D003
VOUT = 1.2 V
VIN = 3.6 V
VIN = 5 V
1%
0.8%
Accuracy
0.6%
0.4%
0.2%
0
-0.2%
-0.4%
-0.6%
-0.8%
0
0.005
0.01
0.015
Output Current (A)
1.2
1.4
1.6
D004
Figure 4-4. DCDC4 Accuracy
1.4%
1.2%
0.6
0.8
1
Output Current (A)
VOUT = 3.3 V
Figure 4-3. DCDC3 Accuracy
Accuracy
1.4
VOUT = 1.1 V
Figure 4-1. DCDC1 Accuracy
0.02
0.025
0.05%
0
-0.05%
-0.1%
-0.15%
-0.2%
-0.25%
-0.3%
-0.35%
-0.4%
-0.45%
-0.5%
-0.55%
-0.6%
VIN = 3.6 V
VIN = 5 V
0
D005
VOUT = 1 V
0.005
0.01
0.015
Output Current (A)
0.02
0.025
D006
VOUT = 1.8 V
Figure 4-5. DCDC5 Accuracy
20
0.6
0.8
1
1.2
Output Current (A)
Figure 4-6. DCDC6 Accuracy
Specifications
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5 Detailed Description
5.1
Overview
The TPS65218 provides three step-down converters, three load switches, three general-purpose I/Os, two
battery backup supplies, one buck-boost converter and one LDO. The system can be supplied by a single
cell Li-Ion battery or regulated 5-V supply. A coin-cell battery can be added to supply the two always-on
backup supplies. The device is characterized across a –40°C to +105°C temperature range, which makes
it suitable for various industrial applications.
The I2C interface provides comprehensive features for using TPS65218. All rails, load switches,, and
GPIOs can be enabled / disabled. Voltage thresholds for the UVLO and supervisor can be customized.
Power-up and power-down sequences can also be programmed through I2C. Interrupts for
overtemperature, overcurrent, and undervoltage can be monitored for the load-switches (LSx).
The integrated voltage supervisor monitors DCDC 1-4 and LDO1. It has two settings; the standard
settings only monitor for undervoltage, while the strict settings implement tight tolerances on both
undervoltage and overvoltage. A power good signal is provided to report the regulation state of the five
rails.
The three hysteretic step-down converters can each supply up to 1.8 A of current. The default output
voltages for each converter can be adjusted through the I2C interface. DCDC 1 and 2 feature dynamic
voltage scaling with adjustable slew rate. The step-down converters operate in a low power mode at light
load, and can be forced into PWM operation for noise sensitive applications.
The battery backup supplies consist of two low power step-down converters optimized for very light loads
and are monitored with a separate power good signal (PGOOD_BU). The converters can be configured to
operate as always-on supplies with the addition of a coin cell battery. The state of the battery can be
monitored over I2C.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
21
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.2
www.ti.com
Functional Block Diagram
PGOOD_BU
To SOC
VDD_10 (1 V)
Battery-backup
22 …F domain supply
L5 10 µH
DCDC6 (1.8 V)
DCDC5_PG
DCDC6_PG
FB5
DCDC5
DCDC6 (1.8 V)
IN_nCC
To SOC
L6 10 µH
FB6
DCDC6
22 …F
IN_BU
2.7-V to 5.5-V
system power
10
Coin
cell
CC
SYS_BU
+
1 …F
4.7 …F 4.7 …F
±
From 1.8-V to 5.5-V
supply
IN_LDO1
0.9-V to 3.3-V analog supply
(adjustable, default 1.8 V)
LDO1
Always-on coin-cell battery backup supplies
LS2
LDO1
IN_LS2
From 3-V to 5.5-V
supply
LS2
100-mA / 500-mA
load switch
10 …F
10 …F
IN_LS1
From 1.2-V to 3.3-V
supply
LS1
200-mA load switch
LS3
LS1
IN_LS3
From 1.8-V to 9.9-V
supply
LS3
500-mA load
switch
10 …F
10 …F
IN_DCDC3
From 2.7-V to 5.5-V
system power
IN_DCDC1
4.7 …F
4.7 …F
FB3
10 …F
DCDC3
DCDC1
IN_DCDC
From 2.7-V to 5.5-V
system power
4.7 …F
FB1
1.1-V core supply
(adjustable)
10 …F
IN_DCDC2
From 2.7-V to 5.5-V
system power
4.7 …F
L4A
L2 10 µH
L4B
DCDC4
DCDC2
FB2
1.1-V MPU supply
(adjustable)
10 …F
DCDC4
3.3-V I/O supply
(adjustable)
IN_BIAS
47 …F
System power
PFI
VREF
VIO
10
SDA
From SOC
PWR_EN
From SOC
1 …F
Supervisor
and up, down
sequencer
OD
+
±
OD
I2C
nWAKEUP
OD
To SOC
To SOC
To SOC
To SOC
DIGITAL
GPIO1
IN_LS1
AC_DET
IN_BIAS
100 k
Momentatary push-button
nPFO
nINT
100 k
IN_BIAS
100 k
VIO
VIO
VIO
VDD_18
(1.8 V / (1.8 V / (DCDC6) (1.8 V /
3.3 V)
3.3 V) 3.3 V)
PGOOD
OD
SCL
10
INT_LDO
BIAS
VSELECT
VDCDC1
VDCDC2
VDCDC3
VDCDC4
LDO1
VIO
From 2.7-V to 5.5-V
system power
100 nF
DC34_SEL
From external
charger
From 2.7-V to 5.5-V
system power
L1 10 µH
L3
1.5-V DDR3 supply
(adjustable)
From SOC
Battery-backup
domain supply
OD
GPIO2
OD
GPIO3
PB
From SOC
To DDR3 memory
From SOC
OD
Thermal
Pad
Copyright © 2017, Texas Instruments Incorporated
22
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
5.3
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Feature Description
5.3.1
Wake-Up and Power-Up and Power-Down Sequencing
The TPS65218 has a predefined power-up and power-down sequence, which in a typical application does
not need to be changed. The user can define custom sequences with I2C. The power-up sequence is
defined by a series of ten strobes and nine delay times. Each output rail is assigned to a strobe to
determine the order of enabling rails. A single rail is assigned to only one strobe, but multiple rails can be
assigned to the same strobe. The delay times between strobes are between 2 ms and 5 ms.
5.3.1.1
Power-Up Sequencing
When the power-up sequence initiates, STROBE1 occurs, and any rail assigned to this strobe is enabled.
After a delay time of DLY1, STROBE2 occurs and the rail assigned to this strobe is powered up. The
sequence continues until all strobes occur and all DLYx times execute. Strobe assignments and delay
times are defined in the SEQx registers, and are changed under I2C control. The power-up sequence
executes if one of the following events occurs:
• From the OFF state:
– The push-button (PB) is pressed (falling edge on PB) OR
– The AC_DET pin is pulled low (falling edge) OR
– The PWR_EN is asserted (driven to high-level) OR
– The main power is connected (IN_BIAS) and AC_DET is grounded AND
– The device is not in undervoltage lockout (UVLO) or overtemperature shutdown (OTS).
• From the PRE_OFF state:
– The PB is pressed (falling edge on PB) OR
– The AC_DET pin is pulled low (falling edge) OR
– PWR_EN is asserted (driven to high-level) AND
– The device is not in UVLO or OTS.
• From the SUSPEND state:
– The PB is pressed (falling edge on PB) OR
– The AC_DET pin is pulled low (falling edge) OR
– The PWR_EN pin is pulled high (level sensitive) AND
– The device is not in UVLO or OTS.
When a power-up event is detected, the device enters a WAIT_PWR_EN state and triggers the power-up
sequence. The device remains in WAIT_PWR_EN as long as the PWR_EN and either the PB or AC_DET
pin are held low. If both, the PB and AC_DET return to logic-high state and the PWR_EN pin has not been
asserted within 20 s of entering WAIT_PWR_EN state, the power-down sequence is triggered and the
device returns to OFF state. Once PWR_EN is asserted, the device advances to ACTIVE state, which is
functionally equivalent to WAIT_PWR_EN. However, the AC_DET pin is ignored and power-down is
controlled by the PWR_EN pin only.
Rails not assigned to a strobe (SEQ = 0000b) are not affected by power-up and power-down sequencing
and remain in their current ON/OFF state regardless of the sequencer. A rail can be enabled/disabled at
any time by setting the corresponding enable bit in the ENABLEx register, with the exception that the
ENABLEx register cannot be accessed while the sequencer is active. Enable bits always reflect the
current enable state of the rail, for example the sequencer sets and resets the enable bits for the rails
under its control.
NOTE
The power-up sequence is defined by strobes and delay times, and can be triggered by the
PB, AC_DET (not shown, same as PB), or PWR_EN pin.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
23
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
PB (input)
nWAKEUP
(output)
PWR_EN
(input)
DLY1
DLY2
DLY3
DLY4
DLY5
DLY6
DLY7
DLY8
DLY9
STROBE1
STROBE2
STROBE 3
STROBE 4
STROBE 5
STROBE 6
STROBE 7
STROBE 8
STROBE 9 STROBE 10
SEQ = 0001b SEQ = 0010b SEQ = 0011b SEQ = 0100b SEQ = 0101b SEQ = 0110b SEQ = 0111b SEQ = 1000b SEQ = 1001b SEQ = 1010b
Push-button deglitch time is not shown.
Figure 5-1. Power-Up Sequences from OFF or SUSPEND State;
PB is Power-Up Event
PB (input)
nWAKEUP
(output)
PWR_EN
(input)
DLY1
DLY2
DLY3
DLY4
DLY5
DLY6
DLY7
DLY8
DLY9
STROBE1
STROBE2
STROBE 3
STROBE 4
STROBE 5
STROBE 6
STROBE 7
STROBE 8
STROBE 9 STROBE 10
SEQ = 0001b SEQ = 0010b SEQ = 0011b SEQ = 0100b SEQ = 0101b SEQ = 0110b SEQ = 0111b SEQ = 1000b SEQ = 1001b SEQ = 1010b
Figure 5-2. Power-Up Sequences from SUSPEND State;
PWR_EN is Power-Up Event
FAULT Recovery
PB (input)
nWAKEUP
(output)
PWR_EN
(input)
DLY1
DLY2
DLY3
DLY4
DLY5
DLY6
DLY7
DLY8
DLY9
STROBE1
STROBE2
STROBE 3
STROBE 4
STROBE 5
STROBE 6
STROBE 7
STROBE 8
STROBE 9 STROBE 10
SEQ = 0001b SEQ = 0010b SEQ = 0011b SEQ = 0100b SEQ = 0101b SEQ = 0110b SEQ = 0111b SEQ = 1000b SEQ = 1001b SEQ = 1010b
Figure 5-3. Power-Up Sequences from RECOVERY State
24
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
5.3.1.2
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Power-Down Sequencing
By default, the power-down sequence follows the reverse of the power-up sequence. When the powerdown sequence is triggered, STROBE10 occurs and any rail assigned to STROBE10 is shut down and its
discharge circuit is enabled. After a delay time of DLY9, STROBE9 occurs and any rail assigned to it is
shut down and its discharge circuit is enabled. The sequence continues until all strobes occur and all
DLYx times execute. The DLYx times are extended by a factor of 10x to provide ample time for discharge,
and preventing output voltages from crossing during shut-down. The DLYFCTR bit is applied globally to all
power-down delay times. Regardless of the DLYx and DLYFCTR settings, the PMIC enters OFF,
SUSPEND, or RECOVERY state 500 ms after the power-down sequence initiates, to ensure that the
discharge circuits remain enabled for a minimum of 150 ms before the next power-up sequence starts.
A power-down sequence executes if one of the following events occurs:
• The device is in the WAIT_PWR_EN state, the PB and AC_DET pins are high, PWR_EN is low, and
the 20-s timer has expired.
• The device is in the ACTIVE state and the PWR_EN pin is pulled low.
• The device is in the WAIT_PWR_EN, ACTIVE, or SUSPEND state and the push-button is held low for
> 8 s (15 s if TRST = 1b)
• A fault occurs in the IC (OTS, UVLO, PGOOD failure).
When transitioning from ACTIVE to SUSPEND state, rails not controlled by the power-down sequencer
maintains the same ON/OFF state in SUSPEND state that it had in ACTIVE state. This allows for the
selected power rails to remain powered up when in the SUSPEND state.
When transitioning to the OFF or RECOVERY state, rails not under sequencer control are shut-down as
follows:
• DCDC1, 2, 3, 4, LDO1, and LS1 shut down at the beginning of the power-down sequence, if not under
sequencer control (SEQ = 0b).
• LS2 and LS3 shut down as the state machine enters an OFF or RECOVERY state; 500 ms after the
power-down sequence is triggered.
If the supply voltage on IN_BIAS drops below 2.5 V, the digital core is reset and all power rails are shut
down instantaneously and are pulled low to ground by their internal discharge circuitry (DCDC1-4, and
LDO1). The amount of time the discharge circuitry remains active is a function of the INT_LDO hold up
time (see Section 5.3.1.6 for more details).
5.3.1.3
Strobes 1 and 2
STROBE1 and STROBE2 are dedicated to DCDC5 and DCDC6 which are always-on; powered up as
soon as the device exits the OFF state, and ON in any other state. STROBE 1 and 2 options are available
only for DCDC5 and DCDC6, not for any other rails.
STROBE 1 and STROBE 2 occur in every power-up sequence, regardless if the rail is already powered
up. If the rail is not to be powered up, its respective strobe setting must be set to 0x00.
When a power-down sequence initiates, STROBE1 and STROBE2 occur only if the FSEAL bit is 0b.
Otherwise, both strobes are omitted and DCDC5 and DCDC6 maintain state.
NOTE
The power-down sequence follows the reverse of the power-up sequence. STROBE2 and
STROBE1 are executed only if FSEAL bit is 0b.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
25
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
PB (input)
nWAKEUP
(output)
PWR_EN
(input)
DLY9
DLY8
DLY7
DLY6
DLY5
DLY4
DLY3
DLY2
DLY1
STROBE 10 STROBE 9
STROBE 8
STROBE 7
STROBE 6
STROBE 5
STROBE 4
STROBE 3
STROBE2
STROBE1
SEQ = 1010b SEQ = 1001b SEQ = 1000b SEQ = 0111b SEQ = 0110b SEQ = 0101b SEQ = 0100b SEQ = 0011b SEQ = 0010b SEQ = 0001b
Figure 5-4. Power-Down Sequences to OFF State;
PWR_EN is Power-Down Event; FSEAL = 0b
PB (input)
nWAKEUP
(output)
PWR_EN
(input)
DLY9
DLY8
DLY7
DLY6
DLY5
DLY4
DLY3
STROBE 10 STROBE 9
STROBE 8
STROBE 7
STROBE 6
STROBE 5
STROBE 4
STROBE 3
SEQ = 1010b SEQ = 1001b SEQ = 1000b SEQ = 0111b SEQ = 0110b SEQ = 0101b SEQ = 0100b SEQ = 0011b
STROBE2 and STROBE1 are not shown.
Figure 5-5. Power-Down Sequences to SUSPEND State;
PWR_EN is Power-Down Event; FSEAL = 1b
PB (input)
PWR_EN
(input)
FAULT
nWAKEUP
(output)
DLY9
DLY8
DLY7
DLY6
DLY5
DLY4
DLY3
STROBE 10 STROBE 9
STROBE 8
STROBE 7
STROBE 6
STROBE 5
STROBE 4
STROBE 3
SEQ = 1010b SEQ = 1001b SEQ = 1000b SEQ = 0111b SEQ = 0110b SEQ = 0101b SEQ = 0100b SEQ = 0011b
STROBE2 and STROBE1 are not shown.
Figure 5-6. Power-Down Sequences to RECOVERY State;
TSD or UV is Power-Down Event; FSEAL = 1b
26
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
5.3.1.4
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Supply Voltage Supervisor and Power Good (PGOOD)
Power-good (PGOOD) is an open-drain output of the built-in voltage supervisor that monitors DCDC1,
DCDC2, DCDC3, DCDC4, and LDO1. The output is Hi-Z when all enabled rails are in regulation and
driven low when one or more rails encounter a fault which brings the output voltage outside the specified
tolerance range. In a typical application PGOOD drives the reset signal of the SOC.
The supervisor has two modes of operation, controlled by the STRICT bit. With the STRICT bit set to 0, all
enabled rails of the five regulators are monitored for undervoltage only with relaxed thresholds and
deglitch times. With the STRCT bit set to 1, all enabled rails of the five regulators are monitored for
undervoltage and overvoltage with tight limits and short deglitch times. Table 5-1 summarizes these
details.
Table 5-1. Supervisor Characteristics Controlled by the STRICT Bit
PARAMETER
STRICT = 0b (TYP)
STRICT = 1b (TYP)
90%
96.5% (DCDC1, DCDC2)
95.5% (DCDC3, DCDC4, LDO1)
Deglitch (output falling)
1 ms
50 µs
Deglitch (output rising)
10 µs
10 µs
Threshold (output falling)
N/A
103.5% (DCDC1, DCDC2)
104.5% (DCDC3, DCDC4, LDO1)
Deglitch (output falling)
N/A
1 ms
Deglitch (output rising)
N/A
50 µs
Threshold (output falling)
Undervoltage
monitoring
Overvoltage
monitoring
Overvoltage threshold
(output rising)
LDO1
Hysteresis
Undervoltage threshold
(output falling)
Hysteresis
Power-good comparator
output (internal signal)
Voltage droop has no effect on
PGOOD output if duration is
less than deglitch time.
Voltage droop has no effect on
PGOOD output if duration is
less than deglitch time.
PGOOD
Deglitch time
Figure 5-7. Definition of Undervoltage, Overvoltage Thresholds, Hysteresis, and Deglitch Times
The following rules apply to the PGOOD output:
• The power-up default state for PGOOD is low. When all rails are disabled, PGOOD output is driven
low.
• Only enabled rails are monitored. Disabled rails are ignored.
• Power-good monitoring of a particular rail starts 5 ms after the rail is enabled and is continuously
monitored thereafter. This allows the rail to power-up.
• PGOOD is delayed by PGDLY time after the sequencer is finished and the last rail is enabled.
• If an enabled rail is continuously outside the monitoring threshold for longer than the deglitch time,
PGOOD is pulled low, and all rails are shut-down following the power-down sequence. PGDLY does
not apply.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
27
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
•
•
•
www.ti.com
Disabling a rail manually by resetting the DCx_EN or LDO1_EN bit has no effect on the PGOOD pin. If
all rails are disabled, PGOOD is driven low as the last rail is disabled.
If the power-down sequencer is triggered, PGOOD is driven low.
PGOOD is driven low in SUSPEND state, regardless of the number of rails that are enabled.
Figure 5-8 shows a typical power-up sequence and PGOOD timing.
VSYS
5 s (maximum)
PB
nWAKEUP
PWR_EN
(deglitched)
LDO1
DLY1 + DLY2
5 ms
DLY4 + DLY3
PG LDO1
(internal)
DCDC3
FAULT
DLY3 + DLY4
5 ms
DLY6 + DLY5
PG DCDC3
(internal)
DLY5 + DLY6
DCDC4
5 ms
DLY7
PG DCDC4
(internal)
DLY7
DCDC1
5 ms
DLY8
PG DCDC1
(internal)
DLY8
DCDC2
5 ms
DLY9
PG DCDC2
(internal)
PG_DLY
PGOOD
Figure 5-8. Typical Power-Up Sequence of the Main Output Rails
5.3.1.5
Backup Supply Power-Good (PGOOD_BU)
PGOOD_BU is a push-pull output indicating if DCDC5 and DCDC6 are in regulation. The output is driven
to high when both rails are in regulation, and driven low if at least one of the rails is below the power-good
threshold. The output-high level is equal to the output voltage of DCDC6.
PGOOD_BU is the logical AND between PGOOD(DCDC5) and PGOOD(DCDC6), and has no delay time
built-in. Unlike main power-good, a fault on DCDC5 or DCDC6 does not trigger the power-down
sequencer, does not disable any of the rails in the system, and has no effect on the PGOOD pin. DCDC5
and DCDC6 recover automatically once the fault is removed.
NOTE
In this example, the power-down is triggered by a fault on DCDC3.
28
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
VSYS
5 s (maximum)
PB
nWAKEUP
PWR_EN
(deglitched)
DCDC6
PG DCDC6
(internal)
DCDC5
DLY1
PG DCDC5
(internal)
PGOOD_BU
Figure 5-9. Typical Power-Up Sequence of DCDC5 and DCDC6
5.3.1.6
Internal LDO (INT_LDO)
The internal LDO provides a regulated voltage to the internal digital core and analog circuitry. The internal
LDO has a nominal output voltage of 2.5 V and can support up to 10 mA of external load.
When system power fails, the UVLO comparator triggers the power-down sequence. If system power
drops below 2.5 V, the digital core is reset and all remaining power rails are shut down instantaneously
and are pulled low to ground by their internal discharge circuitry (DCDC1-4, and LDO1).
The internal LDO reverse blocks to prevent the discharging of the output capacitor (CINT_LDO) on the
INT_LDO pin. The remaining charge on the INT_LDO output capacitor provides a supply for the power rail
discharge circuitry to ensure the outputs are discharged to ground even if the system supply has failed.
The amount of hold-up time specified in Section 4.5 is a function of the output capacitor value (CINT_LDO)
and the amount of external load on the INT_LDO pin, if any. The design allows for enough hold-up time to
sufficiently discharge DCDC1-4, and LDO1 to ensure proper processor power-down sequencing. The
amount of hold-up time is a function of the output capacitor value, which should not exceed 22 μF and the
amount of external load, if any.
From
system
power
IN_BIAS
INT_LDO
10 …F
UVLO
RESET
Digital Core
Power-Rail
Discharge Circuitry
EEPROM
Figure 5-10. Internal LDO and UVLO Sensing
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
29
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.3.1.7
www.ti.com
Current Limited Load Switches
The TPS65218 provides three current limited load switches with individual inputs, outputs, and enable
control. Each switch provides the following control and diagnostic features:
• The ON/OFF state of the switch is controlled by the corresponding LSx_EN bit in the ENABLE register.
• LS1 can be controlled by the sequencer or through I2C communication.
• LS2 and LS3 can ONLY be controlled through I2C communication. The sequencer has no control over
LS2 and LS3.
• Each switch has an active discharge function, disabled by default, and enabled through the
LSxDCHRG bit. When enabled, the switch output is discharged to ground whenever the switch is
disabled.
• When the PFI input drops below the power-fail threshold (the power-fail comparator trips), the load
switches are automatically disabled to shed system load. This function must be individually enabled for
each switch through the corresponding LSxnPFO bit. The switches do not turn back on automatically
as the system voltage recovers, and must be manually re-enabled.
• An interrupt (LSx_I) issues whenever a load switch actively limits the output current, such as when the
output load exceeds the current limit value. The switch remains ON and provides current to the load
according to the current-limit setting.
• All three load switches have local overtemperature sensors which disable the corresponding switch if
the power dissipation and junction temperature exceeds safe operating value. The switch automatically
recovers once the temperature drops below the OTS threshold value minus hysteresis. The LSx_F
(fault) interrupt bit is set while the switch is held OFF by the OTS function.
5.3.1.7.1 Load Switch 1 (LS1)
LS1 is a non-reverse blocking, low-voltage (< 3.6 V), low-impedance switch intended to support DDRx
self-refresh mode by cutting off the DDRx supply to the SOC DDRx interface during SUSPEND mode. In a
typical application, the input of LS1 is tied to the output of DCDC3 while the output of LS1 is connected to
the memory-interface supply pin of the SOC. LS1 can be controlled by the internal sequencer, just as any
power rail.
LS1_EN
LS1DIS
LS1nPFO
SOC
IN_LS1
LS1
From DCDC3
250
10 …F
DDR Memory
Interface
LS1_I
LS1_F
Figure 5-11. Typical Application of Load Switch 1
30
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.3.1.7.2 Load Switch 2 (LS2)
LS2 is a reverse-blocking, 5 V, low-impedance switch. Load switch 2 provides four different current limit
values (100/200/500/1000 mA) that are selectable through LS2ILIM[1:0] bits. Overcurrent is reported
through the LS2_I interrupt.
LS2 has its own input-undervoltage protection which forces the switch OFF if the switch input voltage
(VIN_LS2) is <2.7 V. Similar to OTS, the LS2_F interrupt is set when the switch is held OFF by the local
UVLO function, and the switch recovers automatically when the input voltage rises above the UVLO
threshold.
LS2_EN
LS2DIS
LS2nPFO
LS2ILIM[1:0]
IN_LS2
LS2
+5 V
5-V boost
0.1 …F
250
120 …F
GND
5-V
Port
LS2_I
LS2_F
Figure 5-12. Typical Application of Load Switch 2
5.3.1.7.3 Load Switch 3 (LS3)
LS3 is a non-reverse blocking, medium-voltage (< 10 V), low-impedance switch that can be used to
provide 1.8-V to 10-V power to an auxiliary port. LS3 has four selectable current limit values that are
selectable through LS3ILIM[1:0].
LS3_EN
LS3DIS
LS3nPFO
LS3ILIM[1:0]
IN_LS3
LS3
From any
1.8-V to 10-V supply
250
VPORT
0.1 …F
120 …F
GND
AUX
Port
LS3_I
LS3_F
Figure 5-13. Typical Application of Load Switch 3
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
31
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.3.1.8
www.ti.com
LDO1
LDO1 is a general-purpose LDO intended to provide power to analog circuitry on the SOC. LDO1 has an
input voltage range from 1.8 V to 5.5 V, and can be connected either directly to the system power or the
output of a DCDC converter. The output voltage is programmable in the range of 0.9 V to 3.4 V with a
default of 1.8 V. LDO1 supports up to 200 mA at the minimum specified headroom voltage, and up to 400
mA at the typical operating condition of VOUT = 1.8 V, VIN_LDO1 > 2.7 V.
5.3.1.9
Coin Cell Battery Voltage Acquisition
CC
10
LOW (2.3 V)
+
DISABLED
+
±
CC_AQ = 1
Coin Cell
VREF
±
GOOD (2.6 V)
+
Enable 100-k
load resistor on CC
input.
Enable comparators.
VREF
±
CC_STAT[1:0]
IDEAL (3 V)
LOGIC CORE
+
VREF
±
Wait 600 ms
LOAD ENABLE
Latch comparator outputs;
Store result in CC_STAT[1:0]
Disable 100-k load resistor.
Disable comparators
Restore CC_AQ bit to 0 (CC_AQ = 0)
Issue interrupt (CC_AQC = 1)
CC_STAT[1:0] = 00b ± VCC < VLOW; Coin cell is not present or at end-of-life (EOL)
CC_STAT[1:0] = 01b ± VLOW < VCC < VGOOD; Coin cell is LOW
CC_STAT[1:0] = 10b ± VGOOD < VCC < VIDEAL; Coin cell is GOOD
CC_STAT[1:0] = 11b ± VIDEAL < VCC; Coin cell voltage is IDEAL
Figure 5-14. Left: Flow Chart for Acquiring Coin Cell Battery Voltage
Right: Comparator Circuit
5.3.1.10 UVLO
Depending on the slew rate of the input voltage into the IN_BIAS pin, the power rails of TPS65218 will be
enabled at either VULVO or VULVO + VHYS.
If the slew rate of the IN_BIAS voltage is greater than 30 V/s, then TPS65218 will power up at VULVO.
Once the input voltage rises above this level, the input voltage may drop to the VUVLO level before the
PMIC shuts down. In this scenario, if the input voltage were to fall below VUVLO but above 2.55 V, the input
voltage would have to recover above VUVLO in less than 5 ms for the device to remain active.
32
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
If the slew rate of the IN_BIAS voltage is less than 30 V/s, then TPS65218 will power up at VULVO + VHYS.
Once the input voltage rises above this level, the input voltage may drop to the VUVLO level before the
PMIC shuts down. In this scenario, if the input voltage were to fall below VUVLO but above 2.5 V, the input
voltage would have to recover above VUVLO + VHYS in less than 5 ms for the device to remain active.
In either slew rate scenario, if the input voltage were to fall below 2.5 V, the digital core is reset and all
remaining power rails are shut down instantaneously and are pulled low to ground by their internal
discharge circuitry (DCDC1-4, and LDO1).
UVLO hysteresis
UVLO threshold, supply falling
< 5 ms
VIN_BIAS
UVLO active
UVLO (internal signal)
UVLO inactive
> 5-ms
deglitch
Figure 5-15. Definition of UVLO and Hysteresis, IN_BIAS Slew Rate > 30 V/s
UVLO hysteresis
UVLO threshold, supply falling
< 5 ms
VIN_BIAS
UVLO active
UVLO (internal signal)
UVLO inactive
> 5-ms
deglitch
Figure 5-16. Definition of UVLO and Hysteresis, IN_BIAS Slew Rate < 30 V/s
After the UVLO triggers, the internal LDO blocks current flow from its output capacitor back to the IN_BIAS
pin, allowing the digital core and the discharge circuits to remain powered for a limited amount of time to
properly shut-down and discharge the output rails. The hold-up time is determined by the value of the
capacitor connected to INT_LDO. See Section 5.3.1.6 for more details.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
33
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.3.1.11 Power-Fail Comparator
The power-fail comparator notifies the system host if the system supply voltage drops and the system is at
risk of shutting down. The comparator has an internal 800-mV threshold and the trip-point is adjusted by
an external resistor divider.
By default, the power-fail comparator has no impact on any of the power rails or load switches. Load
switches are configured individually, to be disabled when the PFI comparator trips to shed system load
and extend hold-up time as described in Section 5.3.1.7. The power-fail comparator also triggers the
power-down sequencer, such that all or selective rails power down when the system voltage fails. To tie
the power-fail comparator into the power-down sequence, the OFFnPFO bit in the CONTROL register
must be set to 1.
The power-fail comparator cannot be monitored by software, such that no interrupt or status bit is
associated to this function.
System supply voltage
nPFO
PFI
+
VREF
(800 mV)
Deglitch
±
PFI hysteresis
PFI threshold, supply falling
<25 µs
VPFI
nPFO inactive
nPFO (pin)
nPFO active
10-ms deglitch
25-µs deglitch
Figure 5-17. Power-Fail Comparator Simplified Circuit and Timing Diagram
34
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.3.1.12 Battery-Backup Supply Power-Path
VSYS_BU
DCDC5 and DCDC6 are supplied from either the CC (coin-cell battery) input or IN_BU (main system
supply). The power-path is designed to prioritize IN_BU to maximize coin-cell battery life. Whenever the
PMIC is powered-up (WAIT_PWR_EN, ACTIVE, SUSPEND, RECOVERY state), the power-path is forced
to select the IN_BU input. In OFF mode the power-path selects the higher of the two inputs with a built-in
hysteresis of 150 mV as shown in Figure 5-18.
VIN_BU,
VSYS_BU
VCC
VCC
VIN_BU
VSYS_BU
VINT_LDO
VINT_LDO = 2.5 V
150 mV
0V
ACTIVE State OFF State, FSEAL = 1b
Rapid decay of VIN_BIAS (preregulator)
VCC
VIN_BU
Figure 5-18. Switching Behavior of the BatteryBackup-Supply Power-Path;
Power-Path Hysteresis
Figure 5-19. Switching Behavior of the BatteryBackup-Supply Power-Path;
Main Power Supply Removal
VIN_BU
VSYS_BU
VINT_LDO
VUVLO
VUVLO + VHYST
VCC
VINT_LDO = 2.5 V
VINT_LDO = 2.5 V
VIN_BU
VSYS_BU
VINT_LDO
VCC = 2.2 V
ACTIVE State OFF State, FSEAL = 1b
VIN_BU= 2.05 V
(VIN_BIAS slow decay)
ACTIVE State OFF State, FSEAL = 1b
VIN_BIAS slow decay
Figure 5-20. Switching Behavior of the BatteryBackup-Supply Power-Path;
Weakening Main Battery, Strong Coin-Cell
Figure 5-21. Switching Behavior of the BatteryBackup-Supply Power-Path;
Weakening Main Battery, Weak Coin-Cell
When VIN_BIAS drops below the UVLO threshold, the PMIC shuts down all rails and enters OFF mode. At
this point the power-path selects the higher of the two input supplies. If the coin-cell battery is less than
150 mV above the UVLO threshold, SYS_BU remains connected to IN_BU (see Figure 5-20). If the coincell is >150 mV above the UVLO threshold, the power-path switches to the CC input as shown in
Figure 5-21. With no load on the main supply, the input voltage may recover over time to a value greater
than the coin-cell voltage and the power-path switches back to IN_BU. This is a typical behavior in a Li-Ion
battery powered system.
Depending on the system load, VIN_BIAS may drop below VINT_LDO before the power-down sequence is
completed. In that case, INT_LDO is turned OFF and the digital core is reset forcing the unit into OFF
mode and the power-path switches to IN_BU as shown in Figure 5-19.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
35
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.3.1.13 DCDC3 / DCDC4 Power-Up Default Selection
INT_LDO
10 µA
DC34_SEL current source disabled.
All comparators disabled.
SOURCE ENABLE
DC34_SEL
+
Sequence is triggered by any
event forcing register reset
1200 mV
RSEL
+
Enable 10 µA DC34_SEL current source.
Enable comparators.
825 mV
575 mV
400 mV
Disable comparators
Disable DC34_SEL current source.
100 mV
V3
DCDC4[5:0]
V2
V1
±
+
Start power-up sequencer
DCDC3[5:0]
±
+
163 mV
LOGIC CORE
±
+
275 mV
V4
±
+
Latch comparator outputs;
Depending on result, over-write
DCDC3[5:0] and / or DCDC4[5:0]
power-up default.
V5
±
+
Wait 100 µs
V6
±
V0
±
Figure 5-22. Left: Flow Chart for Selecting DCDC Power-Up Default Voltage
Right: Comparator Circuit
Table 5-2. Power-Up Default Values of DCDC3 and DCDC4
RSEL [KΩ]
MIN
36
TYP
POWER-UP DEFAULT
MAX
DCDC3[5:0]
DCDC4[5:0]
0
0
7.7
Programmed default (1.2 V)
Programmed default (3.3 V)
11.3
12.1
13
0x12 (1.35 V)
Programmed default (3.3 V)
18.1
20
22
0x18 (1.5 V)
Programmed default (3.3 V)
30.9
31.6
32.3
0x1F (1.8 V)
Programmed default (3.3 V)
44.8
45.3
46.4
64.2
64.9
92.9
95.3
135.3
150
0x3D (3.3 V)
0x01 (1.2 V)
Programmed default (1.2 V)
0x07 (1.35 V)
96.9
Programmed default (1.2 V)
0x0D (1.5 V)
Tied to
INT_LDO
Programmed default (1.2 V)
0x14 (1.8 V)
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.3.1.14 I/O Configuration
The device has two GPIOs and one GPO pin which are configured as follows:
• GPIO1:
– General-purpose, open-drain output controlled by GPO1 user bit or sequencer
– DDR3 reset input signal from SOC. Signal is either latched or pass-through to GPO2 pin. See
Table 5-3 for details.
• GPO2:
– General-purpose output controlled by GPO2 user bit
– DDR3 reset output signal. Signal is controlled by GPIO1 and PGOOD. See Table 5-4 for details.
– Output buffer is configured as open-drain or push-pull.
• GPIO3:
– General-purpose, open-drain output controlled by GPO3 user bit or sequencer
– Reset input-signal for DCDC1 and DCDC2
Table 5-3. GPIO1 Configuration
IO1_SEL
(EEPROM)
GPO1
(USER BIT)
PGOOD
(PMIC SIGNAL)
GPIO1
(I/O PIN)
0
0
X
0
0
1
X
HiZ
1
X
0
X
Pin is configured as input and intended as DDR RESET
signal. Coming out of POR, GPO2 is driven low. Otherwise,
GPO2 status is latched at falling edge of PGOOD. See
Figure 5-25.
1
X
1
0
Pin is configured as input and intended as DDR RESET
signal. GPO2 is driven low.
1
X
1
1
Pin is configured as input and intended as DDR RESET
signal. GPO2 is driven high.
COMMENTS
Open-drain output, driving low
Open-drain output, HiZ
Table 5-4. GPO2 Configuration
IO1_SEL
(EEPROM)
GPO2_BUF
(EEPROM)
GPO2
(USER BIT)
0
0
0
GPO2 is open drain output controlled by GPO2 user bit (driving low).
0
0
1
GPO2 is open drain output controlled by GPO2 user bit (HiZ).
0
1
0
GPO2 is push-pull output controlled by GPO2 user bit (driving low).
0
1
1
GPO2 is push-pull output controlled by GPO2 user bit (driving high).
1
0
X
GPO2 is open drain output controlled by GPIO1/PGOOD.
1
1
X
GPO2 is push-pull output controlled by GPIO1/PGOOD.
COMMENTS
Table 5-5. GPIO3 Configuration
DC12_RST
(EEPROM)
GPO3
(USER BIT)
GPIO3
(I/O PIN)
0
0
0
0
1
HiZ
1
X
Active low
COMMENTS
Open-drain output, driving low
Open-drain output, HiZ
GPIO3 is DCDC1 and DCDC2 reset input signal to PMIC (active low). See
Section 5.3.1.14.2 for details.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
37
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.3.1.14.1 Configuring GPO2 as Open-Drain Output
GPO2 may be configured as open-drain or push-pull output. The supply for the push-pull driver is
internally connected to the IN_LS1 input pin, whereas an external pullup resistor and supply are required
in the open-drain configuration. Because of the internal connection to IN_LS1, the external pullup supply
must not exceed the voltage on the IN_LS1 pin, otherwise leakage current may be observed from GPO2
to IN_LS1 as shown in Figure 5-23.
IN_LS1
External
pullup supply
Leakage path if external
pullup supply is > IN_LS1
GPO2
Push-Pull
Driver
Open-Drain
Driver
Figure 5-23. GPO2 as Open-Drain Output
NOTE
When configured as open-drain output, the external pullup supply must not exceed the
voltage level on IN_LS1 pin.
5.3.1.14.2 Using GPIO3 as Reset Signal to DCDC1 and DCDC2
With the DC12_RST bit set to 1, GPIO3 is an edge-sensitive reset input to the PMIC. The reset signal
affects DCDC1 and DCDC2 only, so that only those two registers are reset to the power-up default
whenever GPIO3 input transitions from high to low, while all other registers maintain their current values.
DCDC1 and DCDC2 transition back to the default value following the SLEW settings, and are not power
cycled. This function recovers the processor from reset events while in low-power mode.
38
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
PGOOD (1ms delayed)
GPIO1
Latch,
Gating
IO1_SEL (EEPROM: 0b = output, 1b = input)
GPO1 (user register bit / sequencer control enabled)
GPO2_BUF (EEPROM: 0b = open drain, 1b = push-pull)
IN_LS1
GPO2
EN
1
0
GPO2 (user register bit)
DC12_RST (EEPROM: 0b = disabled, 1b = enabled)
GPIO3
DCDC1/2 reset
GPO3 (user register bit, sequencer control enabled)
Figure 5-24. I/O Pin Logic
PMIC power-up
PGOOD
GPIO1 (DDR_RESET_IN)
(coming from SOC)
1 ms
GPO2 (DDR_RESET_OUT)
(going to DDR memory)
1 ms
RESET_OUT follows RESET_IN
RESET_IN is latched
RESET_OUT follows RESET_IN
Figure 5-25. DDR3 Reset Timing Diagram
NOTE
GPIO must be configured as input (IO1_SEL = 1b). GPO2 is automatically configured as
output.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
39
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.3.1.15 Push Button Input (PB)
The PB pin is a CMOS-type input used to power-up the PMIC. Typically, the PB pin is connected to a
momentary switch to ground and an external pullup resistor. The power-up sequence is triggered if the PB
input is held low for 600 ms.
<100 ms
PB pin (input)
System Power
(5.5 V)
Push
Button
100 ms
50 ms
100 k
PB
PB deglitched
(internal signal)
550 ms
Power-up event
(internal signal)
Figure 5-26. Left: Typical PB Input Circuit
Right: Push-Button Input (PB) Deglitch and Power-Up Timing
In ACTIVE mode, the TPS65218 monitors the PB input and issues an interrupt when the pin status
changes, such as when it drops below or rises above the PB input-low or input-high thresholds. The
interrupt is masked by the PBM bit in the INT_MASK1 register.
40
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
PB is pressed, INT
pin is pulled low,
PB_STATE bit is
set
PB is released.
INT pin is pulled
low, PB_STATE bit
is reset.
PB is pressed, INT
pin is pulled low,
PB_STATE bit is
set
PB is released before
INT register is read
through I2C. INT pin
remains low,
PB_STATE bit is reset
PB pin
(50-ms deglitched input)
nWAKEUP
150 µs
PB interrupt bit
INT pin (output)
PB_STATE bit
I2C access to INT register
INT register is read
through I2C while PB
remains pressed. INT
pin is released,
PB_STATE bit remains
set.
INT register is read
through I2C. INT pin is
released.
INT register is read
through I2C.
Figure 5-27. PB Input-Low or Input-High Thresholds
NOTE
Interrupts are issued whenever the PB pin status changes. The PB_STATE bit reflects the
current status of the PB input. nWAKEUP is pulled low for 150 µs on every falling edge of
PB.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
41
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.3.1.15.1 Signaling PB-Low Event on the nWAKEUP Pin
In ACTIVE state, the nWAKEUP pin is pulled low for five 32-kHz clock cycles (approximately 150 µs)
whenever a falling edge on the PB input is detected. This allows the host processor to wakeup from DEEP
SLEEP mode of operation. It is recommended to pull-up the nWAKEUP pin to DCDC6 output through a 1MΩ resistor.
5.3.1.15.2 Push Button Reset
If the PB input is pulled low for 8 s (15 s if TRST = 1b) or longer, all rails except for DCDC5 and DCDC6
are disabled, and the device enters the RECOVERY state. The device powers up automatically after the
500 ms power-down sequence is complete, regardless of the state of the PB input. Holding the PB pin low
for 8 s (15 s if TRST = 1b), only turns off the device temporarily and forces a system restart, and is not a
power-down function. If the PB is held low continuously, the device power-cycles in 8-s and 15-s intervals.
5.3.1.16 AC_DET Input (AC_DET)
The AC_DET pin is a CMOS-type input used in three different ways to control the power-up of the PMIC:
• In a battery operated system, AC_DET is typically connected to an external battery charger with an
open-drain power-good output pulled low when a valid charger supply is connected to the system. A
falling edge on the AC_DET pin causes the PMIC to power up.
• In a non-portable system, the AC_DET pin may be shorted to ground and the IC powers up whenever
system power is applied to the chip.
• If none of the above behaviors are desired, AC_DET may be tied to system power (IN_BIAS). Powerup is then controlled through the push-button input or PWR_EN input.
System Power
(5.5 V)
System Power
(5.5 V)
100 k
AC_DET
AC_DET
(A)
A.
B.
C.
AC_DET
(B)
(C)
Portable Systems
Non-portable Systems
Disabled
Figure 5-28. AC_DET Pin Configurations
<100 ms
AC_DET pin
(input)
AC_DET
deglitched
(internal signal)
10 ms
100 ms
Power-up event
(internal signal)
Figure 5-29. AC_DET Input Deglitch and Power-Up Timing (Portable Systems)
42
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
In ACTIVE state, the TPS65218 monitors the AC_DET input and issues an interrupt when the pin status
changes, such as when it drops below or rises above the AC_DET input-low or input-high thresholds. The
interrupt is masked by the ACM bit in the INT_MASK1 register.
AC goes low, INT
pin is pulled low,
PC_STATE bit is
set
AC goes high. INT
pin is pulled low,
AC_STATE bit is
reset.
AC goes low, INT
pin is pulled low,
AC_STATE bit is
set
AC goes high before
INT register is read
through I2C. INT pin
remains low,
AC_STATE bit is reset
AC_DET pin
(10-ms deglitched input)
AC interrupt bit
INT pin (output)
AC_STATE bit
I2C access to INT register
INT register is read
through I2C while AC
remains low. INT pin is
released, AC_STATE bit
remains set.
INT register is read
through I2C. INT pin is
released.
INT register is read
through I2C.
Figure 5-30. AC_STATE Pin
NOTE
Interrupts are issued whenever the AC_DET pin status changes. The AC_STATE bit reflects
the current status of the AC_DET input.
5.3.1.17 Interrupt Pin (INT)
The interrupt pin signals any event or fault condition to the host processor. Whenever a fault or event
occurs in the IC, the corresponding interrupt bit is set in the INT register, and the open-drain output is
pulled low. The INT pin is released (returns to Hi-Z state) and fault bits are cleared when the host reads
the INT register. If a failure persists, the corresponding INT bit remains set and the INT pin is pulled low
again after a maximum of 32 µs.
The MASK register masks events from generating interrupts. The MASK settings affect the INT pin only,
and have no impact on the protection and monitor circuits.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
43
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.3.1.18 I2C Bus Operation
The TPS65218 hosts a slave I2C interface (address 0x24) that supports data rates up to 400kbps, autoincrement addressing.
(1)
Slave Address + R/nW
A4
A3
A2
A1
A0 R/nW A
S7
S6
S5
S4
S3
S2
Data
S
A6
S
Start Condition
A
Acknowledge
A6
...
A0
Device Address
Read, Not Write
P
Stop Condition
S7
...
S0
Subaddress
R/nW
A5
Register Address
S1
S0
A
D7
D6
D5
D4
D7
D3
...
D2
D0
D1
D0
A
P
Data
Figure 5-31. Subaddress in I2C Transmission
The I2C bus is a communications link between a controller and a series of slave terminals. The link is
established using a two-wired bus consisting of a serial clock signal (SCL) and a serial data signal (SDA).
The serial clock is sourced from the controller in all cases where the serial data line is bi-directional for
data communication between the controller and the slave terminals. Each device has an open drain output
to transmit data on the serial data line. An external pullup resistor must be placed on the serial data line to
pull the drain output high during data transmission.
Data transmission initiates with a start bit from the controller as shown in Figure 5-33. The start condition
is recognized when the SDA line transitions from high to low during the high portion of the SCL signal.
Upon reception of a start bit, the device receives serial data on the SDA input and checks for valid
address and control information. If the appropriate slave address is set for the device, the device issues
an acknowledge pulse and prepares to receive register address and data. Data transmission is completed
by either the reception of a stop condition or the reception of the data word sent to the device. A stop
condition is recognized as a low to high transition of the SDA input during the high portion of the SCL
signal. All other transitions of the SDA line must occur during the low portion of the SCL signal. An
acknowledge issues after the reception of valid slave address, register-address, and data words. The I2C
interfaces auto-sequence through register addresses, so that multiple data words can be sent for a given
I2C transmission. Reference Figure 5-32 and Figure 5-33 for details.
S
SLAVE ADDRESS
W A
REGISTER ADDRESS
A
DATAREGADDR
A
DATASUBADDR+n
A
DATASUBADDR+n+1
A
P
n bytes + ACK
S
SLAVE ADDRESS
W
A
REGISTER ADDRESS
A
S
SLAVE ADDRESS
R
DATAREGADDR+n
A
A
DATAREGADDR
DATAREGADDR+n+1
A
A
P
n bytes + ACK
From master to slave
R Read (high)
S Start
A Not Acknowledge
From slave to master
W Write (low)
P Stop
A Acknowledge
Top: Master Writes Data to Slave
Bottom: Master Reads Data from Slave
Figure 5-32. I2C Data Protocol
(1)
44
Note: The SCL duty cycle at 400 kHz must be >40%.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
SDA
1-7
SCL
8
9
1-7
8
9
1-7
8
9
S
P
START
ADDRESS
R/W
ACK
DATA
ACK
DATA
ACK/nACK
STOP
2
Figure 5-33. I C Protocol and Transmission Timing;
I2C Start/Stop/Acknowledge Protocol
SDA
tf
tLOW
tr
tSU;DAT
tHD;STA
tSP
tr
tBUF
SCL
tHD;STA
tSU;STA
tHD;DAT
tSU;STO
tHIGH
S
Sr
tf
P
S
2
Figure 5-34. I C Protocol and Transmission Timing;
I2C Data Transmission Timing
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
45
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.4
www.ti.com
Device Functional Modes
5.4.1
Modes of Operation
ANY STATE
NO POWER
External power and
Coin Cell removed
FSEAL
:0
PB low for > 8 s ||
OTS ||
PGOOD fault
VIN_BIAS < VUVLO ||
(OFFnPFO = 1 & VPFI < power-fail threshold)
SEQ DOWN
(500 ms)
DCDC1..4
DCDC5..6
LDO1
INT_LDO
I2C
PGOOD
PGOOD_BU
nWAKEUP
Registers
= OFF
= FSEAL dependent
= OFF
= ON
= NO
= low
= rail dependent
= low
: GHIDXOW
ANY STATE
SEQ DOWN
(500 ms)
VIN_BIAS > (VUVLO + hysteresis)
VIN_BIAS > (VUVLO + hysteresis) &
PB = high &
AC_DET = high &
PWR_EN = low
PRE_OFF
OFF
VIN_BIAS > (VUVLO + hysteresis) &
(PB (;) || AC_DET (;) ||
PWR_EN = high)
VIN_BIAS > (VUVLO + hysteresis) &
(PB (;) ||
AC_DET (;) ||
PWR_EN = high)
WAIT_PWR_EN
DCDC1..4
DCDC5..6
LDO1
INT_LDO
I 2C
PGOOD
PGOOD_BU
nWAKEUP
Registers
= OFF
= FSEAL dependent
= OFF
= OFF
OTS
= NO
= low
= rail dependent
RECOVERY
= low
: GHIDXOW
DCDC1..4
DCDC5..6
LDO1
INT_LDO
I2C
PGOOD
PGOOD_BU
FSEAL
nWAKEUP
= ON
= ON
= ON
= ON
= YES
= high (rail dependent)
= high (rail dependent)
= can be set to 1 but not to 0
= low
DCDC1..4
DCDC5..6
LDO1
INT_LDO
I2C
PGOOD
PGOOD_BU
FSEAL
nWAKEUP
= ON
= ON
= ON
= ON
= YES
= high (rail dependent)
= high (rail dependent)
= can be set to 1 but not to 0
= HiZ
DCDC1..4
DCDC5..6
LDO1
INT_LDO
I2C
PGOOD
PGOOD_BU
nWAKEUP
DCDC1 reg.
DCDC2 reg.
= seq. dependent
= seq. / FSEAL dependent
= seq. dependent
= ON
= YES
= low
= high (rail dependent)
= HiZ
: GHIDXOW
: GHIDXOW
DCDC1..4
DCDC5..6
LDO1
INT_LDO
I 2C
PGOOD
PGOOD_BU
nWAKEUP
FSEAL
Registers
= OFF
= FSEAL dependent
= OFF
= ON
= NO
= low
= high
= HiZ
= maintains state
: GHIDXOW
PWR_EN = high
20 s time-out &
PB = high &
PWR_EN = low
ACTIVE
PWR_EN = low
DCDC1..4 = OFF &
LDO1 = OFF
SEQ DOWN
(500 ms)
DCDC1 = ON || DCDC2 = ON ||
DCDC3 = ON || DCDC4 = ON ||
LDO1 = ON
SUSPEND
PWR_EN = high ||
AC_DET (;) ||
PB (;)
PB (↓) has 50 ms debounce.
AC_DET (↓) has 10 ms debounce.
(↓) = denotes falling edge of signal.
Figure 5-35. Modes of Operation Diagram
5.4.2
OFF
In OFF mode, the PMIC is completely shut down with the exception of a few circuits to monitor the
AC_DET, PWR_EN and PB input. All power rails are turned off and the registers are reset to their default
values. The I2C communication interface is turned off. This is the lowest-power mode of operation. To exit
OFF mode VIN_BIAS must exceed the UVLO threshold and one of the following wake-up events must occur:
• The PB input is pulled low.
• THE AC_DET input is pulled low.
• The PWR_EN input is pulled high.
46
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
To enter OFF state, ensure all power rails are assigned to e sequencer, then pull the PWR_EN pin low.
Additionally, if the OFFnPFO bit is set to 1b and the PFI input falls below the power fail threshold the
device transitions to the OFF state. If the freshness seal is broken, DCDC5 and DCDC6 remains on in the
OFF state.
If a PGOOD or OTS fault occurs while in the ACTIVE state, TPS65218 will transition to the RESET state.
5.4.3
ACTIVE
This is the typical mode of operation when the system is up and running. All DCDC converters, LDOs, and
load switches are operational and can be controlled through the I2C interface. After a wake-up event, the
PMIC enables all rails controlled by the sequencer and pulls the nWAKEUP pin low to signal the event to
the host processor. The device only enters ACTIVE state if the host asserts the PWR_EN pin within 20 s
after the wake-up event. Otherwise it will enter OFF state. The nWAKEUP pin returns to HiZ mode after
the PWR_EN pin is asserted. ACTIVE state can also be directly entered from SUSPEND state by pulling
the PWR_EN pin high. See SUSPEND state description for details. To exit ACTIVE mode, the PWR_EN
pin must be pulled low.
5.4.4
SUSPEND
SUSPEND state is a low-power mode of operation intended to support system standby. Typically all
power rails are turned off with the exception of any rail with an SEQ register set to 0h. DCDC5 and
DCDC6 also remain enabled if the freshness seal is broken. To enter SUSPEND state, pull the PWR_EN
pin low. All power rails controlled by the power-down sequencer are shut down, and after 500 ms the
device enters SUSPEND state. All rails not controlled by the power-down sequencer will maintain state.
Note that all register values are reset as the device enters the SUSPEND state. The device enters
ACTIVE state after it detects a wake-up event as described in the previous sections.
5.4.5
RESET
The TPS65218 can be reset by holding the PB pin low for more than 8 or 15 s, depending on the value of
the TRST bit. All rails are shut down by the sequencer and all register values reset to their default values.
Rails not controlled by the sequencer are shut down additionally. Note that the RESET function powercycles the device and only temporarily shuts down the output rails. Resetting the device does not lead to
OFF state. If the PB_IN pin is kept low for an extended amount of time, the device continues to cycle
between ACTIVE and RESET state, entering RESET every 8 or 15 s.
The device is also reset if a PGOOD or OTS fault occurs. The TPS65218 remains in the recovery state
until the fault is removed, at which time it transitions back to the ACTIVE state.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
47
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5
5.5.1
www.ti.com
Register Maps
Password Protection
Registers 0x11h through 0x26h are protected against accidental write by a 8-bit password. The password
must be written prior to writing to a protected register and automatically resets to 0x00h after the next I2C
transaction, regardless of the register accessed or transaction type (read or write). The password is
required for write access only and is not required for read access.
To write to a protected register:
1. Write the address of the destination register, XORed with the protection password (0x7Dh), to the
PASSWORD register (0x10h).
2. Write the data to the password protected register.
3. If the content of the PASSWORD register XORed with the address send matches 0x7Dh, the data
transfers to the protected register. Otherwise, the transaction is ignored. In either case the
PASSWORD register resets to 0x00 after the transaction.
The cycle must be repeated for any other register that is Level1 write protected.
5.5.2
Freshness Seal (FSEAL) Bit
The FSEAL (freshness seal) bit prevents accidental shut-down of the always-on supplies, DCDC5 and
DCDC6. The FSEAL bit exists in a default state of 0, and can be set to 1 and reset to 0 once for factory
testing. The second time the bit is set to 1, it remains 1 and cannot reset again under software control.
Coin-cell battery and main supply must be disconnected from the IC to reset the FSEAL bit again. With
the FSEAL bit set to 1, DCDC5 and DCDC6 are forced ON regardless of the state of the DC5_EN and
DC6_EN bit, and the rails do not turn off when the IC enters OFF mode.
A consecutive write of [0xB1, 0xFE, 0xA3] to the password register sets the FSEAL bit to 1. The three
bytes must be written consecutively for the sequence to be valid. No other read or write transactions are
allowed between the three bytes, or the sequence is invalid. After a valid sequence, the FSEAL bit in the
STATUS register reflects the new setting.
After setting the FSEAL bit, the IC can enter OFF or any other mode of operation without affecting the
state of the FSEAL bit, provided the coin-cell supply remains connected to the chip.
A second write of [0xB1, 0xFE, 0xA3] to the password register resets the FSEAL bit to 0. The three bytes
must be written consecutively for the sequence to be valid.
A third write of [0xB1, 0xFE, 0xA3] to the password register sets the FSEAL bit to 1 and locks it into this
state for as long as the coin-cell supply (CC) remains connected to the chip.
5.5.3
FLAG Register
The FLAG register contains a bit for each power rail and GPO to keep track of the enable state of the rails
while the system is suspended. The following rules apply to the FLAG register:
• The power-up default value for any flag bit is 0.
• Flag bits are read-only and cannot be written to.
• Upon entering a SUSPEND state, the flag bits are set to same value as their corresponding ENABLE
bits. Rails and GPOs enabled in a SUSPEND state have flag bits set to 1, while all other flag bits are
set to 0. Flag bits are not updated while in the SUSPEND state or when exiting the SUSPEND state.
• The FLAG register is static in WAIT_PWR_EN and ACTIVE state. The FLAG register reflects the
enable state of DCDC1, 2, 3, 4, LDO1, and GPO1, 2, 3 during the last SUSPEND state.
The host processor reads the FLAG register to determine if the system powered up from the OFF or
SUSPEND state. In the SUSPEND state, typically the DDR memory is kept in self refresh mode and
therefore the DC3_FLG or DC4_FLG bits are set.
48
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
5.5.4
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
TPS65218 Registers
Table 5-6 lists the memory-mapped registers for the TPS65218. All register offset addresses not listed in
Table 5-6 should be considered as reserved locations and the register contents should not be modified.
Table 5-6. TPS65218 Registers
SUBADDRESS
ACRONYM
REGISTER NAME
R/W
PASSWORD
PROTECTED
SECTION
0x0
CHIPID
CHIP ID
R
No
Go
0x1
INT1
INTERRUPT 1
R
No
Go
0x2
INT2
INTERRUPT 2
R
No
Go
0x3
INT_MASK1
INTERRUPT MASK 1
R/W
No
Go
0x4
INT_MASK2
INTERRUPT MASK 2
R/W
No
Go
0x5
STATUS
STATUS
R
No
Go
0x6
CONTROL
CONTROL
R/W
No
Go
0x7
FLAG
FLAG
R
No
Go
0x10
PASSWORD
PASSWORD
R/W
No
Go
0x11
ENABLE1
ENABLE 1
R/W
Yes
Go
0x12
ENABLE2
ENABLE 2
R/W
Yes
Go
0x13
CONFIG1
CONFIGURATION 1
R/W
Yes
Go
0x14
CONFIG2
CONFIGURATION 2
R/W
Yes
Go
0x15
CONFIG3
CONFIGURATION 3
R/W
Yes
Go
0x16
DCDC1
DCDC1 CONTROL
R/W
Yes
Go
0x17
DCDC2
DCDC2 CONTROL
R/W
Yes
Go
0x18
DCDC3
DCDC3 CONTROL
R/W
Yes
Go
0x19
DCDC4
DCDC4 CONTROL
R/W
Yes
Go
0x1A
SLEW
SLEW RATE CONTROL
R/W
Yes
Go
0x1B
LDO1
LDO1 CONTROL
R/W
Yes
Go
0x20
SEQ1
SEQUENCER 1
R/W
Yes
Go
0x21
SEQ2
SEQUENCER 2
R/W
Yes
Go
0x22
SEQ3
SEQUENCER 3
R/W
Yes
Go
0x23
SEQ4
SEQUENCER 4
R/W
Yes
Go
0x24
SEQ5
SEQUENCER 5
R/W
Yes
Go
0x25
SEQ6
SEQUENCER 6
R/W
Yes
Go
0x26
SEQ7
SEQUENCER 7
R/W
Yes
Go
Table 5-7 explains the common abbreviations used in this section.
Table 5-7. Common Abbreviations
Abbreviation
Description
R
Read
W
Write
R/W
Read and write capable
h
Hexadecimal notation of a group of bits
b
Hexadecimal notation of a bit or group of bits
X
Don't care reset value
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
49
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.1
www.ti.com
CHIPID Register (subaddress = 0x0) [reset = 0x5]
CHIPID is shown in Figure 5-36 and described in Table 5-8.
Return to Summary Table.
Figure 5-36. CHIPID Register
7
6
5
CHIP
R-0h
4
3
2
1
REV
R-5h
0
Table 5-8. CHIPID Register Field Descriptions
Bit
Field
Type
Reset
7-3
CHIP
R
0h
Description
Chip ID
0h = TPS65218
1h = Future use
...
1Fh = Future use
2-0
REV
R
5h
Revision code
0h = Revision 1.0
1h = Revision 1.1
2h = Revision 2.0
3h = Revision 2.1
4h = Revision 3.0
5h = Revision 4.0 (D0)
6h = Future use
7h = Future use
50
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
5.5.4.2
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
INT1 Register (subaddress = 0x1) [reset = 0x0]
INT1 is shown in Figure 5-37 and described in Table 5-9.
Return to Summary Table.
Figure 5-37. INT1 Register
7
6
RESERVED
R-0h
5
VPRG
R-0b
4
AC
R-0b
3
PB
R-0b
2
HOT
R-0b
1
CC_AQC
R-0b
0
PRGC
R-0b
Table 5-9. INT1 Register Field Descriptions
Bit
Field
Type
Reset
7-6
RESERVED
R
0h
VPRG
R
0b
5
Description
Programming voltage interrupt
0b = No significance
1b = Input voltage is too low for programming power-up default
values.
4
AC
R
0b
AC_DET pin status change interrupt. Note: Status information is
available in STATUS register
0b = No change in status
1b = AC_DET status change (AC_DET pin changed high to low or
low to high)
3
PB
R
0b
Push-button status change interrupt. Note: Status information is
available in STATUS register
0b = No change in status
1b = Push-button status change (PB changed high to low or low to
high)
2
HOT
R
0b
Thermal shutdown early warning
0b = Chip temperature is below HOT threshold
1b = Chip temperature exceeds HOT threshold
1
CC_AQC
R
0b
Coin cell battery voltage acquisition complete interrupt
0b = No significance
1b = Backup battery status comparators have settled and results are
available in STATUS register
0
PRGC
R
0b
EEPROM programming complete interrupt
0b = No significance
1b = Programming of power-up default settings has completed
successfully
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
51
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.3
www.ti.com
INT2 Register (subaddress = 0x2) [reset = 0x0]
INT2 is shown in Figure 5-38 and described in Table 5-10.
Return to Summary Table.
Figure 5-38. INT2 Register
7
6
RESERVED
R-0h
5
LS3_F
R-0b
4
LS2_F
R-0b
3
LS1_F
R-0b
2
LS3_I
R-0b
1
LS2_I
R-0b
0
LS1_I
R-0b
Table 5-10. INT2 Register Field Descriptions
Bit
Field
Type
Reset
7-6
RESERVED
R
0h
LS3_F
R
0b
5
Description
Load switch 3 fault interrupt
0b = No fault. Switch is working normally.
1b = Load switch exceeded operating temperature limit and is
temporarily disabled.
4
LS2_F
R
0b
Load switch 2 fault interrupt
0b = No fault. Switch is working normally.
1b = Load switch exceeded operating temperature limit or input
voltage dropped below minimum value. Switch is temporarily
disabled.
3
LS1_F
R
0b
Load switch 1 fault interrupt
0b = No fault. Switch is working normally.
1b = Load switch exceeded operating temperature limit and is
temporarily disabled.
2
LS3_I
R
0b
Load switch 3 current-limit interrupt
0b = Load switch is disabled or not in current limit
1b = Load switch is actively limiting the output current (output load is
exceeding current limit value)
1
LS2_I
R
0b
Load switch 2 current-limit interrupt
0b = Load switch is disabled or not in current limit
1b = Load switch is actively limiting the output current (output load is
exceeding current limit value)
0
LS1_I
R
0b
Load switch 1 current-limit interrupt
0b = Load switch is disabled or not in current limit
1b = Load switch is actively limiting the output current (output load is
exceeding current limit value)
52
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
5.5.4.4
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
INT_MASK1 Register (subaddress = 0x3) [reset = 0x0]
INT_MASK1 is shown in Figure 5-39 and described in Table 5-11.
Return to Summary Table.
Figure 5-39. INT_MASK1 Register
7
6
RESERVED
R-0h
5
VPRGM
R/W-0b
4
ACM
R/W-0b
3
PBM
R/W-0b
2
HOTM
R/W-0b
1
CC_AQCM
R/W-0b
0
PRGCM
R/W-0b
Table 5-11. INT_MASK1 Register Field Descriptions
Bit
Field
Type
Reset
7-6
RESERVED
R
0h
VPRGM
R/W
0b
5
Description
Programming voltage interrupt mask bit. Note: mask bit has no effect
on monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
4
ACM
R/W
0b
AC_DET interrupt masking bit.
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
Note: mask bit has no effect on monitoring function
3
PBM
R/W
0b
PB interrupt masking bit. Note: mask bit has no effect on monitoring
function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
2
HOTM
R/W
0b
HOT interrupt masking bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
1
CC_AQCM
R/W
0b
C_AQC interrupt masking bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
0
PRGCM
R/W
0b
PRGC interrupt masking bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
53
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.5
www.ti.com
INT_MASK2 Register (subaddress = 0x4) [reset = 0x0]
INT_MASK2 is shown in Figure 5-40 and described in Table 5-12.
Return to Summary Table.
Figure 5-40. INT_MASK2 Register
7
6
RESERVED
R-0h
5
LS3_FM
R/W-0b
4
LS2_FM
R/W-0b
3
LS1_FM
R/W-0b
2
LS3_IM
R/W-0b
1
LS2_IM
R/W-0b
0
LS1_IM
R/W-0b
Table 5-12. INT_MASK2 Register Field Descriptions
Bit
Field
Type
Reset
7-6
RESERVED
R
0h
LS3_FM
R/W
0b
5
Description
LS3 fault interrupt mask bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
4
LS2_FM
R/W
0b
LS2 fault interrupt mask bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
3
LS1_FM
R/W
0b
LS1 fault interrupt mask bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
2
LS3_IM
R/W
0b
LS3 current-limit interrupt mask bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
1
LS2_IM
R/W
0b
LS2 current-limit interrupt mask bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
0
LS1_IM
R/W
0b
LS1 current-limit interrupt mask bit. Note: mask bit has no effect on
monitoring function
0b = Interrupt is unmasked (interrupt event pulls nINT pin low)
1b = Interrupt is masked (interrupt has no effect on nINT pin)
54
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
5.5.4.6
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
STATUS Register (subaddress = 0x5) [reset = 00XXXXXXb]
Register mask: C0h
STATUS is shown in Figure 5-41 and described in Table 5-13.
Return to Summary Table.
Figure 5-41. STATUS Register
7
FSEAL
R-0b
6
EE
R-0b
5
AC_STATE
R-X
4
PB_STATE
R-X
3
2
1
STATE
R-X
0
CC_STAT
R-X
Table 5-13. STATUS Register Field Descriptions
Bit
7
Field
Type
Reset
FSEAL
R
0b
Description
Freshness seal (FSEAL) status. Note: See Section 5.5.2 for details.
0b = FSEAL is in native state (fresh)
1b = FSEAL is broken
6
EE
R
0b
EEPROM status
0b = EEPROM values have not been changed from factory default
setting
1b = EEPROM values have been changed from factory default
settings
5
AC_STATE
R
X
AC_DET input status bit
0b = AC_DET input is inactive (AC_DET input pin is high)
1b = AC_DET input is active (AC_DET input is low)
4
PB_STATE
R
X
PB input status bit
0b = Push Button input is inactive (PB input pin is high)
1b = Push Button input is active (PB input pin is low)
3-2
STATE
R
X
State machine STATE indication
0h = PMIC is in transitional state
1h = PMIC is in WAIT_PWR_EN state
2h = PMIC is in ACTIVE state
3h = PMIC is in SUSPEND state
1-0
CC_STAT
R
X
Coin cell state of charge. Note: Coin-cell voltage acquisition must be
triggered first before status bits are valid. See CC_AQ bit in
Section 5.5.4.7.
0h = VCC < VLOW_LEVEL; Coin cell is not present or approaching endof-life (EOL)
1h = VLOW_LEVEL < VCC < VGOOD_LEVEL; Coin cell voltage is LOW.
2h = VGOOD_LEVEL < VCC <VIDEAL_LEVEL; Coin cell voltage is GOOD.
3h = VIDEAL < VCC; Coin cell voltage is IDEAL.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
55
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.7
www.ti.com
CONTROL Register (subaddress = 0x6) [reset = 0x0]
CONTROL is shown in Figure 5-42 and described in Table 5-14.
Return to Summary Table.
Figure 5-42. CONTROL Register
7
6
5
4
3
2
RESERVED
R-0h
1
OFFnPFO
R/W-0b
0
CC_AQ
R/W-0b
Table 5-14. CONTROL Register Field Descriptions
Bit
Field
Type
Reset
7-2
RESERVED
R
0h
OFFnPFO
R/W
0h
1
Description
Power-fail shutdown bit
0b = nPFO has no effect on PMIC state
1b = All rails are shut down and PMIC enters OFF state when PFI
comparator trips (nPFO is low)
0
CC_AQ
R/W
0h
Coin Cell battery voltage acquisition start bit
0b = No significance
1b = Triggers voltage acquisition. Bit is automatically reset to 0.
56
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
5.5.4.8
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
FLAG Register (subaddress = 0x7) [reset = 0x0]
FLAG is shown in Figure 5-43 and described in Table 5-15.
Return to Summary Table.
Figure 5-43. FLAG Register
7
GPO3_FLG
R-0b
6
GPO2_FLG
R-0b
5
GPO1_FLG
R-0b
4
LDO1_FLG
R-0b
3
DC4_FLG
R-0b
2
DC3_FLG
R-0b
1
DC2_FLG
R-0b
0
DC1_FLG
R-0b
Table 5-15. FLAG Register Field Descriptions
Bit
7
Field
Type
Reset
GPO3_FLG
R
0b
Description
GPO3 Flag bit
0b = Device powered up from OFF or SUSPEND state and GPO3
was disabled while in SUSPEND.
1b = Device powered up from SUSPEND state and GPO3 was
enabled while in SUSPEND.
6
GPO2_FLG
R
0b
GPO2 Flag bit
0b = Device powered up from OFF or SUSPEND state and GPO2
was disabled while in SUSPEND.
1b = Device powered up from SUSPEND state and GPO2 was
enabled while in SUSPEND.
5
GPO1_FLG
R
0b
GPO1 Flag bit
0b = Device powered up from OFF or SUSPEND state and GPO1
was disabled while in SUSPEND.
1b = Device powered up from SUSPEND state and GPO1 was
enabled while in SUSPEND.
4
LDO1_FLG
R
0b
LDO1 Flag bit
0b = Device powered up from OFF or SUSPEND state and LDO1
was disabled while in SUSPEND.
1b = Device powered up from SUSPEND state and LDO1 was
enabled while in SUSPEND.
3
DC4_FLG
R
0b
DCDC4 Flag bit
0b = Device powered up from OFF or SUSPEND state and DCDC4
was disabled while in SUSPEND.
1b = Device powered up from SUSPEND state and DCDC4 was
enabled while in SUSPEND.
2
DC3_FLG
R
0b
DCDC3 Flag bit
0b = Device powered up from OFF or SUSPEND state and DCDC3
was disabled while in SUSPEND.
1b = Device powered up from SUSPEND state and DCDC3 was
enabled while in SUSPEND.
1
DC2_FLG
R
0b
DCDC2 Flag bit
0b = Device powered up from OFF or SUSPEND state and DCDC2
was disabled while in SUSPEND.
1b = Device powered up from SUSPEND state and DCDC2 was
enabled while in SUSPEND.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
57
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Table 5-15. FLAG Register Field Descriptions (continued)
Bit
0
Field
Type
Reset
DC1_FLG
R
0b
Description
DCDC1 Flag bit
0b = Device powered up from OFF or SUSPEND state and DCDC1
was disabled while in SUSPEND.
1b = Device powered up from SUSPEND state and GDCDC1PO3
was enabled while in SUSPEND.
5.5.4.9
PASSWORD Register (subaddress = 0x10) [reset = 0x0]
PASSWORD is shown in Figure 5-44 and described in Table 5-16.
Return to Summary Table.
Figure 5-44. PASSWORD Register
7
6
5
4
3
2
1
0
PWRD
R/W-0h
Table 5-16. PASSWORD Register Field Descriptions
58
Bit
Field
Type
Reset
7-0
PWRD
R/W
0h
Description
Register is used for accessing password protected registers (see
Section 5.5.1 for details). Breaking the freshness seal (see
Section 5.5.2 for details).Programming power-up default values (see
for details). Read-back always yields 0x00.
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.10 ENABLE1 Register (subaddress = 0x11) [reset = 0x0]
ENABLE1 is shown in Figure 5-45 and described in Table 5-17.
Return to Summary Table.
Password protected.
Figure 5-45. ENABLE1 Register
7
6
RESERVED
R-0h
5
DC6_EN
R/W-0b
4
DC5_EN
R/W-0b
3
DC4_EN
R/W-0b
2
DC3_EN
R/W-0b
1
DC2_EN
R/W-0b
0
DC1_EN
R/W-0b
Table 5-17. ENABLE1 Register Field Descriptions
Bit
Field
Type
Reset
7-6
RESERVED
R
0h
DC6_EN
R/W
0b
5
Description
DCDC6 enable bit. DCDC6 can only be disabled if FSEAL = 0. See
Section 5.5.2 for details.
0b = Disabled
1b = Enabled
4
DC5_EN
R/W
0b
DCDC5 enable bit. Note: At power-up/down this bit is automatically
updated by the internal power sequencer. DCDC5 can only be
disabled if FSEAL = 0. See Section 5.5.2 for details.
0b = Disabled
1b = Enabled
3
DC4_EN
R/W
0b
DCDC4 enable bit. Note: At power-up/down this bit is automatically
updated by the internal power sequencer.
0b = Disabled
1b = Enabled
2
DC3_EN
R/W
0b
DCDC3 enable bit. Note: At power-up/down this bit is automatically
updated by the internal power sequencer.
0b = Disabled
1b = Enabled
1
DC2_EN
R/W
0b
DCDC2 enable bit. Note: At power-up/down this bit is automatically
updated by the internal power sequencer.
0b = Disabled
1b = Enabled
0
DC1_EN
R/W
0b
DCDC1 enable bit. Note: At power-up/down this bit is automatically
updated by the internal power sequencer.
0b = Disabled
1b = Enabled
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
59
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.5.4.11 ENABLE2 Register (subaddress = 0x12) [reset = 0x0]
ENABLE2 is shown in Figure 5-46 and described in Table 5-18.
Return to Summary Table.
Password protected.
Figure 5-46. ENABLE2 Register
7
RESERVED
R-0b
6
GPIO3
R/W-0b
5
GPIO2
R/W-0b
4
GPIO1
R/W-0b
3
LS3_EN
R/W-0b
2
LS2_EN
R/W-0b
1
LS1_EN
R/W-0b
0
LDO1_EN
R/W-0b
Table 5-18. ENABLE2 Register Field Descriptions
Bit
Field
Type
Reset
7
RESERVED
R
0b
6
GPIO3
R/W
0b
Description
General purpose output 3 / reset polarity. Note: If DC12_RST bit
(register 0x14) is set to 1 this bit has no function.
0b = GPIO3 output is driven low
1b = GPIO3 output is HiZ
5
GPIO2
R/W
0b
General purpose output 2. Note: If IO_SEL bit (register 0x13) is set
to 1 this bit has no function.
0b = GPO2 output is driven low
1b = GPO2 output is HiZ
4
GPIO1
R/W
0b
General purpose output 1. Note: If IO_SEL bit (register 0x13) is set
to 1 this bit has no function.
0b = GPO1 output is driven low
1b = GPO1 output is HiZ
3
LS3_EN
R/W
0b
Load switch 3 (LS3) enable bit
0b = Disabled
1b = Enabled
2
LS2_EN
R/W
0b
Load switch 2 (LS2) enable bit
0b = Disabled
1b = Enabled
1
LS1_EN
R/W
0b
Load switch 1 (LS1) enable bit.
0b = Disabled
1b = Enabled
Note: At power-up/down this bit is automatically updated by the
internal power sequencer.
0
LDO1_EN
R/W
0b
LDO1 enable bit.
0b = Disabled
1b = Enabled
Note: At power-up/down this bit is automatically updated by the
internal power sequencer.
60
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.12 CONFIG1 Register (subaddress = 0x13) [reset = 0x4C]
CONFIG1 is shown in Figure 5-47 and described in Table 5-19.
Return to Summary Table.
Password protected.
Figure 5-47. CONFIG1 Register
7
TRST
R/W-0b
6
GPO2_BUF
R/W-1b
5
IO1_SEL
R/W-0b
4
3
PGDLY
R/W-1h
2
STRICT
R/W-1b
1
0
UVLO
R/W-0h
Table 5-19. CONFIG1 Register Field Descriptions
Bit
Field
Type
Reset
7
TRST
R/W
0b
Description
Push-button reset time constant
0b = 8s
1b = 15s
6
GPO2_BUF
R/W
1b
GPO2 output buffer configuration
0b = GPO2 buffer is configured as open-drain
1b = GPO2 buffer is configured as push-pull (high-level is driven to
IN_LS1)
5
IO1_SEL
R/W
0b
GPIO1 / GPO2 configuration bit. See Section 5.3.1.14 for details.
0b = GPIO1 is configured as general-purpose, open-drain output.
GPO2 is independent output
1b = GPIO1 is configured as input, controlling GPO2. Intended for
DDR3 reset signal control.
4-3
PGDLY
R/W
1h
Power-Good delay. Note: Power-good delay applies to rising-edge
only (power-up), not falling edge (power-down or fault)
0h = 10 ms
1h = 20 ms
2h = 50 ms
3h = 150 ms
2
STRICT
R/W
1b
Supply Voltage Supervisor Sensitivity selection. See Section 4.5 for
details.
0b = Power-good threshold (VOUT falling) has wider limits.
Overvoltage is not monitored
1b = Power-good threshold (VOUT falling) has tight limits.
Overvoltage is monitored.
1-0
UVLO
R/W
0h
UVLO setting
0h = 2.75 V
1h = 2.95 V
2h = 3.25 V
3h = 3.35 V
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
61
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.5.4.13 CONFIG2 Register (subaddress = 0x14) [TPS65218 reset = 0xC0; TPS65218B101 reset = 0x80]
CONFIG2 is shown in Figure 5-48 and described in Table 5-20.
Return to Summary Table.
Password protected.
Figure 5-48. CONFIG2 Register
7
DC12_RST
R/W-1b
6
UVLOHYS
R/W-1b
5
4
3
RESERVED
R-0h
2
LS3ILIM
R/W-0h
1
0
LS2ILIM
R/W-0h
Table 5-20. CONFIG2 Register Field Descriptions
Bit
7
Field
Type
Reset
DC12_RST
R/W
1b
Description
DCDC1 and DCDC2 reset-pin enable
0b = GPIO3 is configured as general-purpose output
1b = GPIO3 is configured as warm-reset input to DCDC1 and DCDC2
6
UVLOHYS
R/W
TPS65218: 1b
TPS65218B101: 0h
UVLO hysteresis
0b = 200 mV (1)
1b = 400 mV
5-4
RESERVED
R
0h
3-2
LS3ILIM
R/W
0h
Load switch 3 (LS3) current limit selection
0h = 100 mA, (MIN = 98 mA)
1h = 200 mA, (MIN = 194 mA)
2h = 500 mA, (MIN = 475 mA)
3h = 1000 mA, (MIN = 900 mA)
See the LS3 current limit specification in Section 4.5 for more details.
1-0
LS2ILIM
R/W
0h
Load switch 2 (LS2) current limit selection
0h = 100 mA, (MIN = 94 mA)
1h = 200 mA, (MIN = 188 mA)
2h = 500 mA, (MIN = 465 mA)
3h = 1000 mA, (MIN = 922 mA)
See the LS2 current limit specification in Section 4.5 for more details.
(1)
62
200-mV hysteresis option is available for TPS65218B101
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.14 CONFIG3 Register (subaddress = 0x15) [reset = 0x0]
CONFIG3 is shown in Figure 5-49 and described in Table 5-21.
Return to Summary Table.
Password protected.
Figure 5-49. CONFIG3 Register
7
6
RESERVED
R-0h
5
LS3nPFO
R/W-0b
4
LS2nPFO
R/W-0b
3
LS1nPFO
R/W-0b
2
LS3DCHRG
R/W-0b
1
LS2DCHRG
R/W-0b
0
LS1DCHRG
R/W-0b
Table 5-21. CONFIG3 Register Field Descriptions
Bit
Field
Type
Reset
7-6
RESERVED
R
0b
LS3nPFO
R/W
0b
5
Description
Load switch 3 power-fail disable bit
0b = Load switch status is not affected by power-fail comparator
1b = Load switch is disabled if power-fail comparator trips (nPFO is
low)
4
LS2nPFO
R/W
0b
Load switch 2 power-fail disable bit
0b = Load switch status is not affected by power-fail comparator
1b = Load switch is disabled if power-fail comparator trips (nPFO is
low)
3
LS1nPFO
R/W
0b
Load switch 1 power-fail disable bit
0b = Load switch status is not affected by power-fail comparator
1b = Load switch is disabled if power-fail comparator trips (nPFO is
low)
2
LS3DCHRG
R/W
0b
Load switch 3 discharge enable bit
0b = Active discharge is disabled
1b = Active discharge is enabled (load switch output is actively
discharged when switch is OFF)
1
LS2DCHRG
R/W
0b
Load switch 2 discharge enable bit
0b = Active discharge is disabled
1b = Active discharge is enabled (load switch output is actively
discharged when switch is OFF)
0
LS1DCHRG
R/W
0b
Load switch 1 discharge enable bit
0b = Active discharge is disabled
1b = Active discharge is enabled (load switch output is actively
discharged when switch is OFF)
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
63
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.5.4.15 DCDC1 Register (offset = 0x16) [reset = 0x99]
DCDC1 is shown in Figure 5-50 and described in Table 5-22.
Return to Summary Table.
Note 1: This register is password protected. For more information, see Section 5.5.1.
Note 2: A 5-ms blanking time of the overvoltage and undervoltage monitoring occurs when a write is
performed on the DCDC1 register.
Note 3: To change the output voltage of DCDC1, the GO bit or the GODSBL bit must be set to 1b in
register 0x1A.
Figure 5-50. DCDC1 Register
7
PFM
R/W-1b
6
RESERVED
R-0b
5
4
3
2
1
0
DCDC1
R/W-19h
Table 5-22. DCDC1 Register Field Descriptions
Bit
Field
Type
Reset
7
PFM
R/W
1b
Description
Pulse Frequency Modulation (PFM, also known as pulse-skip-mode)
enable. PFM mode improves light-load efficiency. Actual PFM mode
operation depends on load condition.
0b = Disabled (forced PWM)
1b = Enabled
6
64
RESERVED
R
0b
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Table 5-22. DCDC1 Register Field Descriptions (continued)
Bit
Field
Type
Reset
5-0
DCDC1
R/W
19h
Description
DCDC1 output voltage setting
0h = 0.850
1h = 0.860
2h = 0.870
3h = 0.880
4h = 0.890
5h = 0.900
6h = 0.910
7h = 0.920
8h = 0.930
9h = 0.940
Ah = 0.950
Bh = 0.960
Ch = 0.970
Dh = 0.980
Eh = 0.990
Fh = 1.000
10h = 1.010
11h = 1.020
12h = 1.030
13h = 1.040
14h = 1.050
15h = 1.060
16h = 1.070
17h = 1.080
18h = 1.090
19h = 1.100
1Ah = 1.110
1Bh = 1.120
1Ch = 1.130
1Dh = 1.140
1Eh = 1.150
1Fh = 1.160
20h = 1.170
21h = 1.180
22h = 1.190
23h = 1.200
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
65
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Table 5-22. DCDC1 Register Field Descriptions (continued)
Bit
Field
Type
Reset
Description
24h = 1.210
25h = 1.220
26h = 1.230
27h = 1.240
28h = 1.250
29h = 1.260
2Ah = 1.270
2Bh = 1.280
2Ch = 1.290
2Dh = 1.300
2Eh = 1.310
2Fh = 1.320
30h = 1.330
31h = 1.340
32h = 1.350
33h = 1.375
34h = 1.400
35h = 1.425
36h = 1.450
37h = 1.475
38h = 1.500
39h = 1.525
3Ah = 1.550
3Bh = 1.575
3Ch = 1.600
3Dh = 1.625
3Eh = 1.650
3Fh = 1.675
66
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.16 DCDC2 Register (subaddress = 0x17) [reset = 0x99]
DCDC2 is shown in Figure 5-51 and described in Table 5-23.
Return to Summary Table.
Note 1: This register is password protected. For more information, see Section 5.5.1.
Note 2: A 5-ms blanking time of the overvoltage and undervoltage monitoring occurs when a write is
performed on the DCDC2 register.
Note 3: To change the output voltage of DCDC2, the GO bit or the GODSBL bit must be set to 1b in
register 0x1A.
Figure 5-51. DCDC2 Register
7
PFM
R/W-1b
6
RESERVED
R-0b
5
4
3
2
1
0
DCDC2
R/W-19h
Table 5-23. DCDC2 Register Field Descriptions
Bit
Field
Type
Reset
7
PFM
R/W
1b
Description
Pulse frequency modulation (PFM, also known as pulse-skip-mode)
enable. PFM mode improves light-load efficiency. Actual PFM mode
operation depends on load condition.
0b = Disabled (forced PWM)
1b = Enabled
6
RESERVED
R
0b
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
67
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Table 5-23. DCDC2 Register Field Descriptions (continued)
Bit
Field
Type
Reset
5-0
DCDC2
R/W
19h
Description
DCDC2 output voltage setting
0h = 0.850
1h = 0.860
2h = 0.870
3h = 0.880
4h = 0.890
5h = 0.900
6h = 0.910
7h = 0.920
8h = 0.930
9h = 0.940
Ah = 0.950
Bh = 0.960
Ch = 0.970
Dh = 0.980
Eh = 0.990
Fh = 1.000
10h = 1.010
11h = 1.020
12h = 1.030
13h = 1.040
14h = 1.050
15h = 1.060
16h = 1.070
17h = 1.080
18h = 1.090
19h = 1.100
1Ah = 1.110
1Bh = 1.120
1Ch = 1.130
1Dh = 1.140
1Eh = 1.150
1Fh = 1.160
20h = 1.170
21h = 1.180
22h = 1.190
23h = 1.200
68
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Table 5-23. DCDC2 Register Field Descriptions (continued)
Bit
Field
Type
Reset
Description
24h = 1.210
25h = 1.220
26h = 1.230
27h = 1.240
28h = 1.250
29h = 1.260
2Ah = 1.270
2Bh = 1.280
2Ch = 1.290
2Dh = 1.300
2Eh = 1.310
2Fh = 1.320
30h = 1.330
31h = 1.340
32h = 1.350
33h = 1.375
34h = 1.400
35h = 1.425
36h = 1.450
37h = 1.475
38h = 1.500
39h = 1.525
3Ah = 1.550
3Bh = 1.575
3Ch = 1.600
3Dh = 1.625
3Eh = 1.650
3Fh = 1.675
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
69
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.5.4.17 DCDC3 Register (subaddress = 0x18) [reset = 0x8C]
DCDC3 is shown in Figure 5-52 and described in Table 5-24.
Return to Summary Table.
Note 1: This register is password protected. For more information, see Section 5.5.1.
Note 2: A 5-ms blanking time of the overvoltage and undervoltage monitoring occurs when a write is
performed on the DCDC3 register.
NOTE
Power-up default may differ depending on RSEL value. See Section 5.3.1.13 for details.
Figure 5-52. DCDC3 Register
7
PFM
R/W-1b
6
RESERVED
R-0b
5
4
3
2
1
0
DCDC3
R/W-Ch
Table 5-24. DCDC3 Register Field Descriptions
Bit
Field
Type
Reset
7
PFM
R/W
1b
Description
Pulse Frequency Modulation (PFM, also known as pulse-skip-mode)
enable. PFM mode improves light-load efficiency. Actual PFM mode
operation depends on load condition.
0b = Disabled (forced PWM)
1b = Enabled
6
70
RESERVED
R
0b
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Table 5-24. DCDC3 Register Field Descriptions (continued)
Bit
Field
Type
Reset
5-0
DCDC3
R/W
Ch
Description
DCDC3 output voltage setting
0h = 0.900
1h = 0.925
2h = 0.950
3h = 0.975
4h = 1.000
5h = 1.025
6h = 1.050
7h = 1.075
8h = 1.100
9h = 1.125
Ah = 1.150
Bh = 1.175
Ch = 1.200
Dh = 1.225
Eh = 1.250
Fh = 1.275
10h = 1.300
11h = 1.325
12h = 1.350
13h = 1.375
14h = 1.400
15h = 1.425
16h = 1.450
17h = 1.475
18h = 1.500
19h = 1.525
1Ah = 1.550
1Bh = 1.600
1Ch = 1.650
1Dh = 1.700
1Eh = 1.750
1Fh = 1.800
20h = 1.850
21h = 1.900
22h = 1.950
23h = 2.000
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
71
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Table 5-24. DCDC3 Register Field Descriptions (continued)
Bit
Field
Type
Reset
Description
24h = 2.050
25h = 2.100
26h = 2.150
27h = 2.200
28h = 2.250
29h = 2.300
2Ah = 2.350
2Bh = 2.400
2Ch = 2.450
2Dh = 2.500
2Eh = 2.550
2Fh = 2.600
30h = 2.650
31h = 2.700
32h = 2.750
33h = 2.800
34h = 2.850
35h = 2.900
36h = 2.950
37h = 3.000
38h = 3.050
39h = 3.100
3Ah = 3.150
3Bh = 3.200
3Ch = 3.250
3Dh = 3.300
3Eh = 3.350
3Fh = 3.400
72
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.18 DCDC4 Register (subaddress = 0x19) [reset = 0xB2]
DCDC4 is shown in Figure 5-53 and described in Table 5-25.
Return to Summary Table.
Note 1: This register is password protected. For more information, see Section 5.5.1.
Note 2: A 5-ms blanking time of the overvoltage and undervoltage monitoring occurs when a write is
performed on the DCDC4 register.
NOTE
Power-up default may differ depending on RSEL value. See Section 5.3.1.13 for details. The
Reserved setting should not be selected and the output voltage settings should not be
modified while the converter is operating.
Figure 5-53. DCDC4 Register
7
PFM
R/W-1b
6
RESERVED
R-0b
5
4
3
2
1
0
DCDC4
R/W-32h
Table 5-25. DCDC4 Register Field Descriptions
Bit
Field
Type
Reset
7
PFM
R/W
1b
Description
Pulse Frequency Modulation (PFM, also known as pulse-skip-mode)
enable. PFM mode improves light-load efficiency. Actual PFM mode
operation depends on load condition.
0b = Disabled (forced PWM)
1b = Enabled
6
RESERVED
R
0b
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
73
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Table 5-25. DCDC4 Register Field Descriptions (continued)
Bit
Field
Type
Reset
5-0
DCDC4
R/W
32h
Description
DCDC4 output voltage setting
0h = 1.175
1h = 1.200
2h = 1.225
3h = 1.250
4h = 1.275
5h = 1.300
6h = 1.325
7h = 1.350
8h = 1.375
9h = 1.400
Ah = 1.425
Bh = 1.450
Ch = 1.475
Dh = 1.500
Eh = 1.525
Fh = 1.550
10h = 1.600
11h = 1.650
12h = 1.700
13h = 1.750
14h = 1.800
15h = 1.850
16h = 1.900
17h = 1.950
18h = 2.000
19h = 2.050
1Ah = 2.100
1Bh = 2.150
1Ch = 2.200
1Dh = 2.250
1Eh = 2.300
1Fh = 2.3500
20h = 2.400
21h = 2.450
22h = 2.500
23h = 2.550
74
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Table 5-25. DCDC4 Register Field Descriptions (continued)
Bit
Field
Type
Reset
Description
24h = 2.600
25h = 2.650
26h = 2.700
27h = 2.750
28h = 2.800
29h = 2.850
2Ah = 2.900
2Bh = 2.950
2Ch = 3.000
2Dh = 3.050
2Eh = 3.100
2Fh = 3.150
30h = 3.200
31h = 3.250
32h = 3.300
33h = 3.350
34h = 3.400
35h = reserved
36h = reserved
37h = reserved
38h = reserved
39h = reserved
3Ah = reserved
3Bh = reserved
3Ch = reserved
3Dh = reserved
3Eh = reserved
3Fh = reserved
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
75
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.5.4.19 SLEW Register (subaddress = 0x1A) [reset = 0x6]
SLEW is shown in Figure 5-54 and described in Table 5-26.
Return to Summary Table.
NOTE
Slew-rate control applies to DCDC1 and DCDC2 only. If changing from a higher voltage to
lower voltage while STRICT = 1 and converters are in a no load state, PFM bit for DCDC1
and DCDC2 must be set to 0.
Figure 5-54. SLEW Register
7
GO
R/W-0b
6
GODSBL
R/W-0b
5
4
RESERVED
R-0h
3
2
1
SLEW
R/W-6h
0
Table 5-26. SLEW Register Field Descriptions
Bit
7
Field
Type
Reset
GO
R/W
0b
Description
Go bit. Note: Bit is automatically reset at the end of the voltage
transition
0b = No change
1b = Initiates the transition from present state to the output voltage
setting currently stored in DCDC1 / DCDC2 register. SLEW setting
does apply.
6
GODSBL
R/W
0b
Go disable bit
0b = Enabled
1b = Disabled; DCDC1 and DCDC2 output voltage changes
whenever set-point is updated in DCDC1 / DCDC2 register without
having to write to the GO bit. SLEW setting does apply.
5-3
RESERVED
R
0h
2-0
SLEW
R/W
6h
Output slew rate setting
0h = 160 µs/step (0.0625 mV/µs at 10 mV per step)
1h = 80 µs/step (0.125 mV/µs at 10 mV per step)
2h = 40 µs/step (0.250 mV/µs at 10 mV per step)
3h = 20 µs/step (0.500 mV/µs at 10 mV per step)
4h = 10 µs/step (1.0 mV/µs at 10 mV per step)
5h = 5 µs/step (2.0 mV/µs at 10 mV per step)
6h = 2.5 µs/step (4.0 mV/µs at 10 mV per step)
7h = Immediate; Slew rate is only limited by control loop response
time. Note: The actual slew rate depends on the voltage step per
code. Refer to DCDCx registers for details.
76
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.20 LDO1 Register (subaddress = 0x1B) [reset = 0x1F]
LDO1 is shown in Figure 5-55 and described in Table 5-27.
Return to Summary Table.
Note 1: This register is password protected. For more information, see Section 5.5.1.
Note 2: A 5-ms blanking time of the overvoltage and undervoltage monitoring occurs when a write is
performed on the LDO1 register.
Figure 5-55. LDO1 Register
7
6
5
4
3
RESERVED
R-0h
2
1
0
LDO1
R/W-1Fh
Table 5-27. LDO1 Register Field Descriptions
Bit
Field
Type
Reset
7-6
RESERVED
R
0h
5-0
LDO1
R/W
1Fh
Description
LDO1 output voltage setting
0h = 0.900
1h = 0.925
2h = 0.950
3h = 0.975
4h = 1.000
5h = 1.025
6h = 1.050
7h = 1.075
8h = 1.100
9h = 1.125
Ah = 1.150
Bh = 1.175
Ch = 1.200
Dh = 1.225
Eh = 1.250
Fh = 1.275
10h = 1.300
11h = 1.325
12h = 1.350
13h = 1.375
14h = 1.400
15h = 1.425
16h = 1.450
17h = 1.475
18h = 1.500
19h = 1.525
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
77
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Table 5-27. LDO1 Register Field Descriptions (continued)
Bit
Field
Type
Reset
Description
1Ah = 1.550
1Bh = 1.600
1Ch = 1.650
1Dh = 1.700
1Eh = 1.750
1Fh = 1.800
20h = 1.850
21h = 1.900
22h = 1.950
23h = 2.000
24h = 2.050
25h = 2.100
26h = 2.150
27h = 2.200
28h = 2.250
29h = 2.300
2Ah = 2.350
2Bh = 2.400
2Ch = 2.450
2Dh = 2.500
2Eh = 2.550
2Fh = 2.600
30h = 2.650
31h = 2.700
32h = 2.750
33h = 2.800
34h = 2.850
35h = 2.900
36h = 2.950
37h = 3.000
38h = 3.050
39h = 3.100
3Ah = 3.150
3Bh = 3.200
3Ch = 3.250
3Dh = 3.300
3Eh = 3.350
3Fh = 3.400
78
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.21 SEQ1 Register (subaddress = 0x20) [reset = 0x0]
SEQ1 is shown in Figure 5-56 and described in Table 5-28.
Return to Summary Table.
Password protected.
Figure 5-56. SEQ1 Register
7
DLY8
R/W-0b
6
DLY7
R/W-0b
5
DLY6
R/W-0b
4
DLY5
R/W-0b
3
DLY4
R/W-0b
2
DLY3
R/W-0b
1
DLY2
R/W-0b
0
DLY1
R/W-0b
Table 5-28. SEQ1 Register Field Descriptions
Bit
Field
Type
Reset
7
DLY8
R/W
0b
Description
Delay8 (occurs after Strobe8 and before Strobe9)
0b = 2 ms
1b = 5 ms
6
DLY7
R/W
0b
Delay7 (occurs after Strobe7 and before Strobe8)
0b = 2 ms
1b = 5 ms
5
DLY6
R/W
0b
Delay6 (occurs after Strobe6 and before Strobe7)
0b = 2 ms
1b = 5 ms
4
DLY5
R/W
0b
Delay5 (occurs after Strobe5 and before Strobe6)
0b = 2 ms
1b = 5 ms
3
DLY4
R/W
0b
Delay4 (occurs after Strobe4 and before Strobe5)
0b = 2 ms
1b = 5 ms
2
DLY3
R/W
0b
Delay3 (occurs after Strobe3 and before Strobe4)
0b = 2 ms
1b = 5 ms
1
DLY2
R/W
0b
Delay2 (occurs after Strobe2 and before Strobe3)
0b = 2 ms
1b = 5 ms
0
DLY1
R/W
0b
Delay1 (occurs after Strobe1 and before Strobe2)
0b = 2 ms
1b = 5 ms
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
79
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.5.4.22 SEQ2 Register (subaddress = 0x21) [reset = 0x0]
SEQ2 is shown in Figure 5-57 and described in Table 5-29.
Return to Summary Table.
Password protected.
Figure 5-57. SEQ2 Register
7
DLYFCTR
R/W -0b
6
5
4
3
2
1
RESERVED
R-0h
0
DLY9
R/W -0b
Table 5-29. SEQ2 Register Field Descriptions
Bit
7
Field
Type
Reset
DLYFCTR
R/W
0b
Description
Power-down delay factor
0b = 1x
1b = 10x (delay times are multiplied by 10x during power-down)
Note: DLYFCTR has no effect on power-up timing.
6-1
0
RESERVED
R
0h
DLY9
R/W
0b
Delay9 (occurs after Strobe9 and before Strobe10)
0b = 2 ms
1b = 5 ms
80
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.23 SEQ3 Register (subaddress = 0x22) [reset = 0x98]
SEQ3 is shown in Figure 5-58 and described in Table 5-30.
Return to Summary Table.
Password protected.
Figure 5-58. SEQ3 Register
7
6
5
4
3
2
DC2_SEQ
R/W-9h
1
0
DC1_SEQ
R/W-8h
Table 5-30. SEQ3 Register Field Descriptions
Bit
Field
Type
Reset
7-4
DC2_SEQ
R/W
9h
Description
DCDC2 enable STROBE
0h = Rail is not controlled by sequencer
1h = Rail is not controlled by sequencer
2h = Rail is not controlled by sequencer
3h = Enable at STROBE3
4h = Enable at STROBE4
5h = Enable at STROBE5
6h = Enable at STROBE6
7h = Enable at STROBE7
8h = Enable at STROBE8
9h = Enable at STROBE9
Ah = Enable at STROBE10
Bh = Rail is not controlled by sequencer
Ch = Rail is not controlled by sequencer
Dh = Rail is not controlled by sequencer
Eh = Rail is not controlled by sequencer
Fh = Rail is not controlled by sequencer
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
81
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Table 5-30. SEQ3 Register Field Descriptions (continued)
Bit
Field
Type
Reset
3-0
DC1_SEQ
R/W
8h
Description
DCDC1 enable STROBE
0h = Rail is not controlled by sequencer
1h = Rail is not controlled by sequencer
2h = Rail is not controlled by sequencer
3h = Enable at STROBE3
4h = Enable at STROBE4
5h = Enable at STROBE5
6h = Enable at STROBE6
7h = Enable at STROBE7
8h = Enable at STROBE8
9h = Enable at STROBE9
Ah = Enable at STROBE10
Bh = Rail is not controlled by sequencer
Ch = Rail is not controlled by sequencer
Dh = Rail is not controlled by sequencer
Eh = Rail is not controlled by sequencer
Fh = Rail is not controlled by sequencer
82
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.24 SEQ4 Register (subaddress = 0x23) [reset = 0x75]
SEQ4 is shown in Figure 5-59 and described in Table 5-31.
Return to Summary Table.
Password protected.
Figure 5-59. SEQ4 Register
7
6
5
4
3
2
DC4_SEQ
R/W-7h
1
0
DC3_SEQ
R/W-5h
Table 5-31. SEQ4 Register Field Descriptions
Bit
Field
Type
Reset
7-4
DC4_SEQ
R/W
7h
Description
DCDC4 enable STROBE
0h = Rail is not controlled by sequencer
1h = Rail is not controlled by sequencer
2h = Rail is not controlled by sequencer
3h = Enable at STROBE3
4h = Enable at STROBE4
5h = Enable at STROBE5
6h = Enable at STROBE6
7h = Enable at STROBE7
8h = Enable at STROBE8
9h = Enable at STROBE9
Ah = Enable at STROBE10
Bh = Rail is not controlled by sequencer
Ch = Rail is not controlled by sequencer
Dh = Rail is not controlled by sequencer
Eh = Rail is not controlled by sequencer
Fh = Rail is not controlled by sequencer
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
83
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
Table 5-31. SEQ4 Register Field Descriptions (continued)
Bit
Field
Type
Reset
3-0
DC3_SEQ
R/W
5h
Description
DCDC3 enable STROBE
0h = Rail is not controlled by sequencer
1h = Rail is not controlled by sequencer
2h = Rail is not controlled by sequencer
3h = Enable at STROBE3
4h = Enable at STROBE4
5h = Enable at STROBE5
6h = Enable at STROBE6
7h = Enable at STROBE7
8h = Enable at STROBE8
9h = Enable at STROBE9
Ah = Enable at STROBE10
Bh = Rail is not controlled by sequencer
Ch = Rail is not controlled by sequencer
Dh = Rail is not controlled by sequencer
Eh = Rail is not controlled by sequencer
Fh = Rail is not controlled by sequencer
84
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
5.5.4.25 SEQ5 Register (subaddress = 0x24) [reset = 0x12]
SEQ5 is shown in Figure 5-60 and described in Table 5-32.
Return to Summary Table.
Password protected.
Figure 5-60. SEQ5 Register
7
6
5
4
RESERVED
R-0h
DC6_SEQ
R/W-1h
3
2
RESERVED
R-0h
1
0
DC5_SEQ
R/W-2h
Table 5-32. SEQ5 Register Field Descriptions
Bit
Field
Type
Reset
7-6
RESERVED
R
0h
5-4
DC6_SEQ
R/W
1h
Description
DCDC6 enable STROBE. Note: Strobe 1 and 2 are executed only if
FSEAL = 0. DCDC5 and 6 cannot be disabled by sequencer once
freshness seal is broken.
0h = Rail is not controlled by sequencer
1h = Enable at STROBE1
2h = Enable at STROBE2
3h = Rail is not controlled by sequencer
3-2
RESERVED
R
0h
1-0
DC5_SEQ
R/W
2h
DCDC5 enable STROBE. Note: Strobe 1 and 2 are executed only if
FSEAL = 0. DCDC5 and 6 cannot be disabled by sequencer once
freshness seal is broken.
0h = Rail is not controlled by sequencer
1h = Enable at STROBE1
2h = Enable at STROBE2
3h = Rail is not controlled by sequencer
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
85
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.5.4.26 SEQ6 Register (subaddress = 0x25) [reset = 0x63]
SEQ6 is shown in Figure 5-61 and described in Table 5-33.
Return to Summary Table.
Password protected.
Figure 5-61. SEQ6 Register
7
6
5
4
3
2
LS1_SEQ
R/W-6h
1
0
LDO1_SEQ
R/W-3h
Table 5-33. SEQ6 Register Field Descriptions
Bit
Field
Type
Reset
7-4
LS1_SEQ
R/W
6h
Description
LS1 enable STROBE
0h = Rail is not controlled by sequencer
1h = Rail is not controlled by sequencer
2h = Rail is not controlled by sequencer
3h = Enable at STROBE3
4h = Enable at STROBE4
5h = Enable at STROBE5
6h = Enable at STROBE6
7h = Enable at STROBE7
8h = Enable at STROBE8
9h = Enable at STROBE9
Ah = Enable at STROBE10
Bh = Rail is not controlled by sequencer
Ch = Rail is not controlled by sequencer
Dh = Rail is not controlled by sequencer
Eh = Rail is not controlled by sequencer
Fh = Rail is not controlled by sequencer
86
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Table 5-33. SEQ6 Register Field Descriptions (continued)
Bit
Field
Type
Reset
3-0
LDO1_SEQ
R/W
3h
Description
LDO1 enable STROBE
0h = Rail is not controlled by sequencer
1h = Rail is not controlled by sequencer
2h = Rail is not controlled by sequencer
3h = Enable at STROBE3
4h = Enable at STROBE4
5h = Enable at STROBE5
6h = Enable at STROBE6
7h = Enable at STROBE7
8h = Enable at STROBE8
9h = Enable at STROBE9
Ah = Enable at STROBE10
Bh = Rail is not controlled by sequencer
Ch = Rail is not controlled by sequencer
Dh = Rail is not controlled by sequencer
Eh = Rail is not controlled by sequencer
Fh = Rail is not controlled by sequencer
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
87
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
5.5.4.27 SEQ7 Register (subaddress = 0x26) [reset = 0x3]
SEQ7 is shown in Figure 5-62 and described in Table 5-34.
Return to Summary Table.
Password protected.
Figure 5-62. SEQ7 Register
7
6
5
4
3
2
GPO3_SEQ
R/W-0h
1
0
GPO1_SEQ
R/W-3h
Table 5-34. SEQ7 Register Field Descriptions
Bit
Field
Type
Reset
7-4
GPO3_SEQ
R/W
0h
Description
GPO3 enable STROBE
0h = Rail is not controlled by sequencer
1h = Rail is not controlled by sequencer
2h = Rail is not controlled by sequencer
3h = Enable at STROBE3
4h = Enable at STROBE4
5h = Enable at STROBE5
6h = Enable at STROBE6
7h = Enable at STROBE7
8h = Enable at STROBE8
9h = Enable at STROBE9
Ah = Enable at STROBE10
Bh = Rail is not controlled by sequencer
Ch = Rail is not controlled by sequencer
Dh = Rail is not controlled by sequencer
Eh = Rail is not controlled by sequencer
Fh = Rail is not controlled by sequencer
88
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Table 5-34. SEQ7 Register Field Descriptions (continued)
Bit
Field
Type
Reset
3-0
GPO1_SEQ
R/W
3h
Description
GPO1 enable STROBE
0h = Rail is not controlled by sequencer
1h = Rail is not controlled by sequencer
2h = Rail is not controlled by sequencer
3h = Enable at STROBE3
4h = Enable at STROBE4
5h = Enable at STROBE5
6h = Enable at STROBE6
7h = Enable at STROBE7
8h = Enable at STROBE8
9h = Enable at STROBE9
Ah = Enable at STROBE10
Bh = Rail is not controlled by sequencer
Ch = Rail is not controlled by sequencer
Dh = Rail is not controlled by sequencer
Eh = Rail is not controlled by sequencer
Fh = Rail is not controlled by sequencer
Detailed Description
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
89
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
6 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
6.1
Application Information
The TPS65218 is designed to pair with various application processors. For detailed information on using
TPS65218 with Sitara™ AM335x or Sitara AM437x processors, refer to Powering the AM335x/AM437x
with TPS65218.The typical application in Section 6.2 is based on and uses terminology consistent with the
Sitara™ family of processors.
6.1.1
Applications Without Backup Battery
In applications that require always-on supplies but no battery backup, the CC input to the power path must
be connected to ground.
DCDC6 (1.8 V)
To SOC
L5
PGOOD_BU
DCDC5_PG
DCDC6_PG
DCDC5
FB5
DCDC6 (1.8 V)
To SOC
2.7-V to 5.5-V
system power
IN_nCC
22 …F
VDD_10 (1 V)
Battery backup
domain supply
22 …F
VDD_18 (1.8 V)
Battery backup
domain supply
10 µH
L6 10 µH
DCDC6
FB6
IN_BU
4.7 …F
CC
SYS_BU
1 …F
Always-on coin-cell battery backup supplies
IN_BIAS
From 2.7-V to 6.5-V
system power
INT_LDO
BIAS
100 nF
Figure 6-1. CC Input to Power Path
NOTE
In applications without backup battery, CC input must be tied to ground.
90
Application and Implementation
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
6.1.2
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Applications Without Battery Backup Supplies
In applications that do not require always-on supplies, both inputs and the output of the power-path can
simply be grounded. All pins related to DCDC5 and DCDC6 are also tied to ground, and PGOOD_BU and
IN_nCC are kept floating. With the backup supplies completely disabled, the FSEAL bit in the STATUS
register is undefined and should be ignored.
DCDC6 (1.8 V)
L5
PGOOD_BU
DCDC5_PG
DCDC6_PG
No connect
DCDC5
FB5
DCDC6 (1.8 V)
L6
IN_nCC
DCDC6
No connect
FB6
IN_BU
CC
SYS_BU
Always-on coin-cell battery backup supplies
Figure 6-2. DCDC5 and DCDC6 Pins
NOTE
In applications that do not require always-on supplies, PGOOD_BU and IN_nCC can be kept
floating. All other pins are tied to ground.
Application and Implementation
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
91
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
6.2
www.ti.com
Typical Application
System Power (5.5 V)
DCDC6
VDDSHVx
for GPIOx
VDDSHV3
Push
Button
nWAKEUP
PB
RTC_WAKEUP
nINT
GPIOx
PGOOD
Digital
AC_DET
PWRONRSTn
PWR_EN
RTC_PMIC_EN
SCL/SDA
I2C0_SCL/SDA
GPIO3
10
Coin
Cell
Battery Backup
Supplies
+
±
IN_BU
2.7-V to 5.5-V
system power
PGOOD_BU
CC
IN_LDO1
DCDC5
DCDC6
LDO1
IN_DCDC1
DCDC1 (buck)
IN_DCDC2
IN_DCDC3
IN_DCDC4
IN_BIAS
From DCDC3
IN_LS1
DCDC2 (buck)
DCDC3 (buck)
DCDC4 (buck-boost)
RTC_PWRONRSTn
IN_nCC
1.0V (DCDC5)
CAP_VDD_RTC
1.8V (DCDC6)
VDDS_RTC
1.8V
1.8V Analog & I/O
0.95/1.1V
VDD_CORE
0.95/1.1/1.2/1.26/1.325V
VDD_MPU
1.35/1.5V
3.3V
3.3V Analog & I/O
DDR_RESETn
BIAS
LS1
LS1
VDDS_DDR
TPS65218
DDR3/L Memory
Copyright © 2017, Texas Instruments Incorporated
Figure 6-3. Typical Application Schematic
92
Application and Implementation
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
6.2.1
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Design Requirements
Table 6-1 lists the design requirements.
Table 6-1. Design Parameters
6.2.2
VOLTAGE
SEQUENCE
DCDC1
1.1 V
8
DCDC2
1.1 V
9
DCDC3
1.2 V
5
DCDC4
3.3 V
7
DCDC5
1.0 V
2
DCDC6
1.8 V
1
LDO1
1.8 V
3
Detailed Design Procedure
6.2.2.1
Output Filter Design
The step down converters (DCDC1, DCDC2, and DCDC3) on TPS65218 are designed to operate with
effective inductance values in the range of 1 to 2.2 µH and with effective output capacitance in the range
of 10 to 100 µF. The internal compensation is optimized to operate with an output filter of L = 1.5 µH and
COUT = 10 µF.
The buck boost converter (DCDC4) on TPS65218 is designed to operate with effective inductance values
in the range of 1.2 to 2.2 µH. The internal compensation is optimized to operate with an output filter of L =
1.5 µH and COUT = 47 µF.
The two battery backup converters (DCDC5 and DCDC6) are designed to operate with effective
inductance values in the range of 4.7 to 22 µH. The internal compensation is optimized with an output filter
of L = 10 µH and COUT = 20 µF.
Larger or smaller inductor/capacitance values can be used to optimize performance of the device for
specific operation conditions.
6.2.2.2
Inductor Selection for Buck Converters
The inductor value affects its peak to peak ripple current, the PWM to PFM transition point, the output
voltage ripple, and the efficiency. The selected inductor must be rated for its DC resistance and saturation
current. The inductor ripple current (∆L) decreases with higher inductance and increases with higher VIN or
VOUT. Equation 1 calculates the maximum inductor current ripple under static load conditions. The
saturation current of the inductor should be rated higher than the maximum inductor current as calculated
with Equation 2. This is recommended as during heavy load transient the inductor current will rise above
the calculated value.
V
± OUT
VIN
'I L VOUT u
/u¦
(1)
I L max
I OUT max
'I L
2
where
•
•
•
•
F = Switching frequency
L = Inductor value
∆IL = Peak-to-peak inductor ripple current
ILmax = Maximum inductor current
(2)
Application and Implementation
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
93
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
The following inductors have been used with the TPS65218 (see Table 6-2).
Table 6-2. List of Recommended Inductors
PART NUMBER
VALUE
SIZE (mm) [L × W × H]
MANUFACTURER
INDUCTORS FOR DCDC1, DCDC2, DCDC3, DCDC4
SPM3012T-1R5M
1.5 µH, 2.8 A, 77 mΩ
3.2 × 3.0 × 1.2
TDK
IHLP1212BZER1R5M11
1.5 µH, 4.0 A, 28.5 mΩ
3.6 × 3.0 × 2.0
Vishay
MLZ2012N100L
10 µH, 110 mA, 300 mΩ
2012 / 0805 (2.00 × 1.25 ×
1.25)
TDK
LQM21FN100M80
10 µH, 100 mA, 300 mΩ
2012 / 0805 (2.00 × 1.25 ×
1.25)
Murata
INDUCTORS FOR DCDC5, DCDC6
6.2.2.3
Output Capacitor Selection
The hysteretic PWM control scheme of the TPS65218 switching converters allows the use of tiny ceramic
capacitors. Ceramic capacitors with low ESR values have the lowest output voltage ripple and are
recommended. The output capacitor requires either an X7R or X5R dielectric.
At light load currents the converter operates in power save mode, and the output voltage ripple is
dependent on the output capacitor value and the PFM peak inductor current. Higher output capacitor
values minimize the voltage ripple in PFM Mode and tighten DC output accuracy in PFM mode.
The two battery backup converters (DCDC5 and DCDC6) always operate in PFM mode. For these
converters, a capacitor of at least 20 µF is recommended on the output to help minimize voltage ripple.
The buck-boost converter requires additional output capacitance to help maintain converter stability during
high load conditions. At least 40 µF of output capacitance is recommended and an additional 100-nF
capacitor can be added to further filter output ripple at higher frequencies.
Table 6-2 lists the recommended capacitors.
Table 6-3. List of Recommended Capacitors
PART NUMBER
VALUE
SIZE (mm) [L × W × H]
MANUFACTURER
GRM188R60J105K
1µF
1608 / 0603 (1.6 × 0.8 × 0.8)
Murata
CAPACITORS FOR VOLTAGES UP TO 5.5 V (1)
GRM21BR60J475K
4.7µF
2012 / 0805 (2.0 × 1.25 × 1.25)
Murata
GRM31MR60J106K
10µF
3216 / 1206 (3.2 × 1.6 × 1.6)
Murata
GRM31CR60J226K
22µF
3216 / 1206 (3.2 × 1.6 × 1.6)
Murata
GRM21BR60J106K
10µF
2012 / 0805 (2.0 × 1.25 × 1.25)
Murata
GRM31CR60J476M
47µF
3216 / 1206 (3.2 × 1.6 × 1.6)
Murata
CAPACITORS FOR VOLTAGES UP TO 3.3 V
(1)
94
(1)
The DC bias effect of ceramic capacitors must be considered when selecting a capacitor.
Application and Implementation
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
6.2.3
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Application Curves
at TJ = 25°C unless otherwise noted
100%
90%
80%
80%
70%
Efficiency
Efficiency
60%
60%
40%
50%
40%
30%
20%
20%
VIN = 2.8 V
VIN = 3.6 V
VIN = 5 V
VIN = 2.8 V
VIN = 3.6 V
VIN = 5 V
10%
0
0
0
400.001
800.001
1200.001
Output Current (mA)
1600.001
0
0.2
0.4
D007
0.6
0.8
1
1.2
Output Current(A)
VOUT = 1.1 V
1.4
1.6
1.8
D008
VOUT = 1.2 V
Figure 6-4. DCDC1/DCDC2 Efficiency
Figure 6-5. DCDC3 Efficiency
90%
100%
80%
80%
70%
Efficiency
Efficiency
60%
50%
40%
60%
40%
30%
20%
20%
VIN = 2.8 V
VIN = 3.6 V
VIN = 5 V
10%
0
VIN = 2.7 V
VIN = 3.6 V
VIN = 5 V
0
0
0.2
0.4
0.6
0.8
1
1.2
Output Current (A)
1.4
1.6
1.8
0
0.2
0.4
0.6
0.8
1
Output Current (A)
D009
VOUT = 1.5 V
1.2
1.4
1.6
D010
VOUT = 3.3 V
Figure 6-6. DCDC3 Efficiency
Figure 6-7. DCDC4 Efficiency
90%
85%
80%
Efficiency
75%
70%
65%
60%
55%
50%
DCDC5 (1 V)
DCDC6 (1.8 V)
45%
40%
0
IN_BU = 0 V
0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09
Output Current (mA)
0.1
D011
CC = 3 V
Figure 6-8. DCDC5/DCDC6 Efficiency
Application and Implementation
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
95
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
7 Power Supply Recommendations
The device is designed to operate with an input voltage supply range between 2.7 and 5.5 V. This input
supply can be from a single cell Li-Ion battery or other externally regulated supply. If the input supply is
located more than a few inches from the TPS65218 additional bulk capacitance may be required in
addition to the ceramic bypass capacitors. An electrolytic capacitor with a value of 47 µF is a typical
choice.
The coin cell back up input is designed to operate with a input voltage supply between 2.2 and 3.3 V This
input should be supplied by a coin cell battery with 3-V nominal voltage.
8 Layout
8.1
Layout Guidelines
Follow these layout guidelines:
• The IN_X pins should be bypassed to ground with a low ESR ceramic bypass capacitor. The typical
recommended bypass capacitance is 4.7-µF with a X5R or X7R dielectric.
• The optimum placement is closest to the IN_X pins of the device. Take care to minimize the loop area
formed by the bypass capacitor connection, the IN_X pin, and the thermal pad (PowerPAD for the
HTQFP packageof the device.
• The thermal pad should be tied to the PCB ground plane with a minimum of 25 vias. See Figure 8-2 for
an example.
• The LX trace should be kept on the PCB top layer and free of any vias.
• The FBX traces should be routed away from any potential noise source to avoid coupling.
• DCDC4 Output capacitance should be placed immediately at the DCDC4 pin. Excessive distance
between the capacitance and DCDC4 pin may cause poor converter performance.
8.2
Layout Example
VOUT
Output Filter
Capacitor
L1
Via to Ground Plane
Via to Internal Plane
FB1
Input Bypass
Capacitor
IN
Thermal
Pad
Figure 8-1. Layout Recommendation
96
Layout
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
s
Recommended Thermal Pad via size
Hole size (s) = 8 mil
Diameter (d) = 16 mil
d
Figure 8-2. PowerPAD™ Layout Recommendation
Layout
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
97
Not Recommended for New Designs
TPS65218
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
www.ti.com
9 Device and Documentation Support
9.1
9.1.1
Device Support
Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES
NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR
SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR
SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
9.2
9.2.1
Documentation Support
Related Documentation
For related documentation see the following:
• Texas Instruments, Basic Calculation of a Buck Converter's Power Stage application report
• Texas Instruments, Design Calculations for Buck-Boost Converters application report
• Texas Instruments, Empowering Designs With Power Management IC (PMIC) for Processor
Applications application report
• Texas Instruments, Powering the AM335x/AM437x with TPS65218 user's guide
• Texas Instruments, TPS65218EVM user's guide
• Texas Instruments, TPS65218 Power Management Integrated Circuit (PMIC) for Industrial Applications
application report
9.3
Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the
upper right corner, click on Alert me to register and receive a weekly digest of any product information that
has changed. For change details, review the revision history included in any revised document.
9.4
Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the
respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views;
see TI's Terms of Use.
TI E2E™ Online Community The TI engineer-to-engineer (E2E) community was created to foster
collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge,
explore ideas and help solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools
and contact information for technical support.
9.5
Trademarks
PowerPAD, Sitara, E2E are trademarks of Texas Instruments.
Cortex is a trademark of ARM Ltd.
ARM is a registered trademark of ARM Ltd.
All other trademarks are the property of their respective owners.
98
Device and Documentation Support
Copyright © 2014–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS65218
Not Recommended for New Designs
TPS65218
www.ti.com
9.6
SLDS206D – NOVEMBER 2014 – REVISED JANUARY 2018
Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
9.7
Glossary
TI Glossary This glossary lists and explains terms, acronyms, and definitions.
10 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and
revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2014–2018, Texas Instruments Incorporated
Mechanical, Packaging, and Orderable Information
Submit Documentation Feedback
Product Folder Links: TPS65218
99
PACKAGE OPTION ADDENDUM
www.ti.com
16-May-2018
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TPS65218B101PHPR
NRND
HTQFP
PHP
48
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 105
65218B101
TPS65218B101PHPT
NRND
HTQFP
PHP
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 105
65218B101
TPS65218B1PHPR
NRND
HTQFP
PHP
48
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 105
T65218B1
TPS65218B1PHPT
NRND
HTQFP
PHP
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 105
T65218B1
TPS65218B1RSLR
NRND
VQFN
RSL
48
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 105
TPS
65218B1
TPS65218B1RSLT
NRND
VQFN
RSL
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 105
TPS
65218B1
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
16-May-2018
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Sep-2019
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TPS65218B101PHPR
HTQFP
PHP
48
TPS65218B101PHPT
HTQFP
PHP
TPS65218B1PHPR
HTQFP
PHP
TPS65218B1PHPT
HTQFP
TPS65218B1RSLR
TPS65218B1RSLT
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
1000
330.0
16.4
9.6
9.6
1.5
12.0
16.0
Q2
48
250
330.0
16.4
9.6
9.6
1.5
12.0
16.0
Q2
48
1000
330.0
16.4
9.6
9.6
1.5
12.0
16.0
Q2
PHP
48
250
330.0
16.4
9.6
9.6
1.5
12.0
16.0
Q2
VQFN
RSL
48
2500
330.0
16.4
6.3
6.3
1.1
12.0
16.0
Q2
VQFN
RSL
48
250
180.0
16.4
6.3
6.3
1.1
12.0
16.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Sep-2019
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS65218B101PHPR
HTQFP
PHP
48
1000
336.6
336.6
31.8
TPS65218B101PHPT
HTQFP
PHP
48
250
336.6
336.6
31.8
TPS65218B1PHPR
HTQFP
PHP
48
1000
336.6
336.6
31.8
TPS65218B1PHPT
HTQFP
PHP
48
250
336.6
336.6
31.8
TPS65218B1RSLR
VQFN
RSL
48
2500
367.0
367.0
38.0
TPS65218B1RSLT
VQFN
RSL
48
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising