Texas Instruments | LMT01 0.5°C Accurate 2-Pin Digital Output Temperature Sensor With Pulse Count Interface (Rev. D) | Datasheet | Texas Instruments LMT01 0.5°C Accurate 2-Pin Digital Output Temperature Sensor With Pulse Count Interface (Rev. D) Datasheet

Texas Instruments LMT01 0.5°C Accurate 2-Pin Digital Output Temperature Sensor With Pulse Count Interface (Rev. D) Datasheet
Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
LMT01 0.5°C Accurate 2-Pin Digital Output Temperature Sensor With Pulse Count
Interface
1 Features
3 Description
•
The LMT01 device is a high-accuracy, 2-pin
temperature sensor with an easy-to-use pulse count
current loop interface, which makes it suitable for
onboard and offboard applications in automotive,
industrial, and consumer markets. The LMT01 digital
pulse count output and high accuracy over a wide
temperature range allow pairing with any MCU
without concern for integrated ADC quality or
availability, while minimizing software overhead. TI’s
LMT01 device achieves a maximum ±0.5°C accuracy
with very fine resolution (0.0625°C) over a
temperature range of –20°C to 90°C without system
calibration or hardware and software compensation.
1
•
•
•
•
•
•
•
High Accuracy Over –50°C to 150°C Wide
Temperature Range
– –20°C to 90°C: ±0.5°C (Maximum)
– 90°C to 150°C: ±0.625°C (Maximum)
– –50°C to –20°C: ±0.7°C (Maximum)
Precision Digital Temperature Measurement
Simplified in a 2-Pin Package
Pulse Count Current Loop Easily Read by
Processor. Number of Output Pulses is
Proportional to Temperature With 0.0625°C
Resolution
Communication Frequency: 88 kHz
Conversion Current: 34 µA
Continuous Conversion Plus Data-Transmission
Period: 100 ms
Floating 2-V to 5.5-V (VP–VN) Supply Operation
With Integrated EMI Immunity
Multiple 2-Pin Package Offerings: TO-92/LPG (3.1
mm × 4 mm × 1.5 mm) – ½ the Size of Traditional
TO-92 and WSON With Wettable Flanks
Device Information(1)
2 Applications
•
•
•
•
•
The LMT01’s pulse count interface is designed to
directly interface with a GPIO or comparator input,
thereby
simplifying
hardware
implementation.
Similarly, the LMT01's integrated EMI suppression
and simple 2-pin architecture makes it suitable for
onboard and offboard temperature sensing in a noisy
environment. The LMT01 device can be easily
converted into a two-wire temperature probe with a
wire length up to two meters. See LMT01-Q1 for the
automotive qualified version.
PART NUMBER
Digital Output Wired Probes
White Goods
HVAC
Power Supplies
Battery Management
PACKAGE
LMT01LPG
TO-92 (2)
4.00 mm × 3.15 mm
LMT01DQX
WSON (2)
1.70 mm × 2.50 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
2-Pin IC Temperature Sensor
LMT01 Accuracy
VDD: 3.0V to 5.5V
GPIO
1.0
0.8
Temperature Accuracy (ƒC)
BODY SIZE (NOM)
Up to 2m
Max Limit
0.6
VP
0.4
0.2
LMT01
0.0
VN
Min 2.0V
-0.2
MCU/
FPGA/
ASIC
GPIO/
COMP
-0.4
-0.6
LMT01 Pulse Count Interface
Min Limit
-0.8
Conversion Time
-1.0
±50
±25
0
25
50
75
100
LMT01 Junction Temperaure (ƒC)
Typical units plotted in center of curve.
125
ADC Conversion Result
150
Power Off
C014
Power On
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
Absolute Maximum Ratings ...................................... 4
ESD Ratings.............................................................. 4
Recommended Operating Conditions ...................... 4
Thermal Information .................................................. 4
Electrical Characteristics........................................... 5
Electrical Characteristics - TO-92/LPG Pulse Count
to Temperature LUT................................................... 6
6.7 Electrical Characteristics - WSON/DQX Pulse Count
to Temperature LUT................................................... 7
6.8 Switching Characteristics .......................................... 7
6.9 Timing Diagram......................................................... 8
6.10 Typical Characteristics ............................................ 9
7
Detailed Description ............................................ 13
7.2 Functional Block Diagram ....................................... 13
7.3 Feature Description................................................. 13
7.4 Device Functional Modes........................................ 16
8
Application and Implementation ........................ 17
8.1 Application Information............................................ 17
8.2 Typical Application .................................................. 18
8.3 System Examples .................................................. 20
9 Power Supply Recommendations...................... 22
10 Layout................................................................... 23
10.1 Layout Guidelines ................................................. 23
10.2 Layout Example .................................................... 23
11 Device and Documentation Support ................. 24
11.1
11.2
11.3
11.4
11.5
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
24
24
24
24
24
12 Mechanical, Packaging, and Orderable
Information ........................................................... 24
7.1 Overview ................................................................. 13
4 Revision History
Changes from Revision C (June 2017) to Revision D
Page
•
Added device stamp to the TO-92 pinout top view ................................................................................................................ 3
•
Changed the TO-92S pin numbers in the Pin Functions........................................................................................................ 3
Changes from Revision B (April 2017) to Revision C
Page
•
Removed Electrical Characteristics: WSON/DQX table; Combined the LPG and DQX Electrical Characteristics
tables together ........................................................................................................................................................................ 5
•
Changed IOL maximum value from: 39 µA to: 40 µA .............................................................................................................. 5
•
Changed leakage value from: 1 µA to 3.5 µA ........................................................................................................................ 5
•
Moved the thermal response time parameters to the Electrical Characteristics table ........................................................... 5
•
Added Missing Cross References ........................................................................................................................................ 13
Changes from Revision A (June 2015) to Revision B
Page
•
Added new WSON/DQX package throughout data sheet ..................................................................................................... 1
•
Changed updated package information. ................................................................................................................................ 3
•
Added Electrical Characteristics - WSON/DQX Pulse Count to Temperature LUT ............................................................... 7
•
Added -40 for Sample Calculations Table ........................................................................................................................... 14
•
Added missing cross reference ........................................................................................................................................... 15
Changes from Original (June 2015) to Revision A
Page
•
Added full datasheet. ............................................................................................................................................................. 1
•
Added clarification note. ........................................................................................................................................................ 1
2
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
5 Pin Configuration and Functions
DQX Package
2-Pin WSON
Bottom View
VP
VN
LPG Package
2-Pin TO-92
Top View
LM
YM
LL
F
T0
1
VN
VP
Pin Functions
PIN
NAME
TO-92S
WSON
VP
2
1
VN
1
2
TYPE
Input
DESCRIPTION
Positive voltage pin; may be connected to system power supply or bias resistor.
Output Negative voltage pin; may be connected to system ground or a bias resistor.
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
3
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
(1) (2)
See
.
MIN
MAX
UNIT
Voltage drop (VP – VN)
−0.3
6
V
Storage temperature, Tstg
−65
175
°C
(1)
(2)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Soldering process must comply with Reflow Temperature Profile specifications. Refer to www.ti.com/packaging.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±750
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
Free-air temperature
MIN
MAX
UNIT
−50
150
°C
2
5.5
V
Voltage drop (VP – VN)
6.4 Thermal Information
LMT01
THERMAL METRIC
(1)
DQX (WSON)
LPG (TO-92)
2 PINS
2 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
213
177
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
71
94
°C/W
RθJB
Junction-to-board thermal resistance
81
152
°C/W
ψJT
Junction-to-top characterization parameter
2.4
33
°C/W
ψJB
Junction-to-board characterization parameter
79
152
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
6.5 Electrical Characteristics
Over operating free-air temperature range and operating VP-VN range (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ACCURACY
Temperature accuracy
Temperature accuracy
(1) (2)
(1) (2)
150°C
–0.625
0.625
°C
125°C
-0.625
0.625
°C
120°C
–0.625
0.625
°C
110°C
–0.5625
0.5625
°C
100°C
VP – VN of
2.15 V to 5.5 V 90°C
–0.5625
0.5625
°C
–0.5
0.5
°C
25°C
–0.5
0.5
°C
–20°C
–0.5
0.5
°C
–30°C
–0.5625
0.5625
°C
–40°C
–0.625
0.625
°C
VP – VN of
–50°C
2.15 V to 5.5 V
–0.6875
±0.4
0.6875
°C
800
808
±0.125
PULSE COUNT TRANSFER FUNCTION
Number of pulses at 0°C
Output pulse range
Theoretical max (exceeds
device rating)
816
15
3228
1
4095
Resolution of one pulse
0.0625
°C
OUTPUT CURRENT
IOL
IOH
Output current variation
Low level
28
34
40
µA
High level
112.5
125
143
µA
3.1
3.7
4.5
40
133
m°C/V
0.002
3.5
µA
High-to-Low level output current ratio
POWER SUPPLY
Accuracy sensitivity to change in VP – VN
2.15 V ≤ VP – VN ≤ 5. 0 V (3)
Leakage Current VP – VN
VDD ≤ 0.4 V
THERMAL RESPONSE
Stirred oil thermal response time to 63% of final value DQX (WSON)
(package only)
LPG (TO-92)
0.4
DQX (WSON)
9.4
LPG (TO-92)
28
Still air thermal response time to 63% of final value
(package only)
(1)
(2)
(3)
0.8
s
s
Calculated using Pulse Count to Temperature LUT and 0.0625°C resolution per pulse, see section Electrical Characteristics - TO92/LPG Pulse Count to Temperature LUT and Electrical Characteristics - WSON/DQX Pulse Count to Temperature LUT.
Error can be linearly interpolated between temperatures given in table as shown in the Accuracy vs Temperature curves in section
Typical Characteristics.
Limit is using end point calculation.
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
5
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
6.6 Electrical Characteristics - TO-92/LPG Pulse Count to Temperature LUT
Over operating free-air temperature range and VP-VN operating range (unless otherwise noted). LUT is short for Look-up
Table.
PARAMETER
Digital output code
6
MIN
TYP
MAX
–50°C
TEST CONDITIONS
15
26
37
–40°C
172
181
190
–30°C
329
338
347
–20°C
486
494
502
–10°C
643
651
659
0°C
800
808
816
10°C
958
966
974
20°C
1117
1125
1133
30°C
1276
1284
1292
40°C
1435
1443
1451
50°C
1594
1602
1610
60°C
1754
1762
1770
70°C
1915
1923
1931
80°C
2076
2084
2092
90°C
2237
2245
2253
100°C
2398
2407
2416
110°C
2560
2569
2578
120°C
2721
2731
2741
130°C
2883
2893
2903
140°C
3047
3057
3067
150°C
3208
3218
3228
Submit Documentation Feedback
UNIT
pulses
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
6.7 Electrical Characteristics - WSON/DQX Pulse Count to Temperature LUT
Over operating free-air temperature range and 2.15 V ≤ VP – VN ≤ 5. 0 V power supply operating range (unless otherwise
noted). LUT is short for Look-up Table.
PARAMETER
Digital output code
MIN
TYP
MAX
–50°C
TEST CONDITIONS
15
26
37
–40°C
172
181
190
–30°C
328
337
346
–20°C
486
494
502
–10°C
643
651
659
0°C
800
808
816
10°C
958
966
974
20°C
1117
1125
1133
30°C
1276
1284
1292
40°C
1435
1443
1451
50°C
1594
1603
1611
60°C
1754
1762
1771
70°C
1915
1923
1931
80°C
2076
2084
2092
90°C
2237
2245
2254
100°C
2398
2407
2416
110°C
2560
2569
2578
120°C
2721
2731
2741
125°C
2802
2814
2826
130°C
2883
2894
2904
140°C
3047
3058
3068
150°C
3210
3221
3231
UNIT
pulses
6.8 Switching Characteristics
Over operating free-air temperature range and operating VP – VN range (unless otherwise noted).
PARAMETER
tR, tF
Output current rise and fall time
fP
Output current pulse frequency
TEST CONDITIONS
Output current duty cycle
tCONV
Temperature conversion time (1)
tDATA
Data transmission time
(1)
MIN
CL = 10 pF, RL = 8 k
2.15 V to 5.5 V
TYP
MAX
1.45
UNIT
µs
82
88
94
40%
50%
60%
kHz
46
50
54
ms
44
47
50
ms
Conversion time includes power up time or device turn on time that is typically 3 ms after POR threshold of 1.2 V is exceeded.
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
7
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
6.9 Timing Diagram
tCONV
tDATA
Power
125µA
34µA
tR
Power Off
Output
Current
tF
1/fP
Figure 1. Timing Specification Waveform
8
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
6.10 Typical Characteristics
1.0
1.0
0.8
Max Limit
Temperature Accuracy (ƒC)
Temperature Accuracy (ƒC)
0.8
0.6
0.4
0.2
0.0
-0.2
-0.4
-0.6
Min Limit
-0.8
0.2
0.0
-0.2
-0.4
-0.6
Min Limit
-1.0
±50
±25
0
25
50
75
100
125
LMT01 Junction Temperaure (ƒC)
150
±50
±25
0
25
50
75
100
125
LMT01 Junction Temperaure (ƒC)
C017
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.15 V
150
C016
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.4 V
Figure 2. Accuracy vs LMT01 Junction Temperature
Figure 3. Accuracy vs LMT01 Junction Temperature
1.0
1.0
0.8
0.8
Max Limit
Temperature Accuracy (ƒC)
Temperature Accuracy (ƒC)
0.4
-0.8
-1.0
0.6
0.4
0.2
0.0
-0.2
-0.4
-0.6
Min Limit
-0.8
Max Limit
0.6
0.4
0.2
0.0
-0.2
-0.4
-0.6
Min Limit
-0.8
-1.0
-1.0
±50
±25
0
25
50
75
100
125
LMT01 Junction Temperaure (ƒC)
150
±50
±25
0
25
50
75
100
125
LMT01 Junction Temperaure (ƒC)
C015
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.7 V
150
C014
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 3 V
Figure 4. Accuracy vs LMT01 Junction Temperature
Figure 5. Accuracy vs LMT01 Junction Temperature
1.0
1.0
0.8
0.8
Max Limit
Temperature Accuracy (ƒC)
Temperature Accuracy (ƒC)
Max Limit
0.6
0.6
0.4
0.2
0.0
-0.2
-0.4
-0.6
Min Limit
-0.8
Max Limit
0.6
0.4
0.2
0.0
-0.2
-0.4
-0.6
Min Limit
-0.8
-1.0
-1.0
±50
±25
0
25
50
75
100
125
LMT01 Junction Temperaure (ƒC)
150
±50
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 4 V
Figure 6. Accuracy vs LMT01 Junction Temperature
±25
0
25
50
75
100
125
LMT01 Junction Temperaure (ƒC)
C013
150
C012
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 5 V
Figure 7. Accuracy vs LMT01 Junction Temperature
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
9
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
Typical Characteristics (continued)
1.00
-0.625°C
Min Limit
Max Limit
0.60
0.625°C
Max Limit
0.40
Frequency
Temperature Accuracy (ƒC)
0.80
0.20
0.00
-0.20
-0.40
-0.60
Min Limit
-0.80
-1.00
±50
±25
0
25
50
75
100
125
150
LMT01 Junction Temperature (ƒC)
-1
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 5.5 V
Figure 9. Accuracy Histogram at 150°C
0.5°C
Max Limit
Frequency
+1
0
Accuracy (ƒC)
-1
C024
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.15 V to 5.5 V
Figure 11. Accuracy Histogram at –20°C
0.5625°C
Max Limit
-0.5625°C
Min Limit
Frequency
+1
0
Accuracy (ƒC)
-1
C022
Using LUT Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.15 V to 5.5 V
0.5625°C
Max Limit
0
Accuracy (ƒC)
+1
C021
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.15 V to 5.5 V
Figure 12. Accuracy Histogram at -30°C
10
C023
Frequency
-0.5625°C
Min Limit
+1
0
Accuracy (ƒC)
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.15 V to 5.5 V
Figure 10. Accuracy Histogram at 30°C
-1
0.5°C
Max Limit
-0.5°C
Min Limit
Frequency
-1
C025
Using Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.15 V to 5.5 V
Figure 8. Accuracy vs LMT01 Junction Temperature
-0.5°C
Min Limit
+1
0
Accuracy (ƒC)
C011
Submit Documentation Feedback
Figure 13. Accuracy Histogram at -40°C
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
Typical Characteristics (continued)
3.0
Temperature Accuracy (ƒC)
2.5
0.6875°C
Max Limit
Frequency
-0.6875°C
Min Limit
2.0
1.5
1.0
0.5
0.0
-0.5
-1.0
-1
+1
0
Accuracy (ƒC)
±50
Using LUT Electrical Characteristics - TO-92/LPG Pulse Count to
Temperature LUT
VP – VN = 2.15 V to 5.5 V
25
50
75
100
125
150
C018
Using Temp = (PC/4096 × 256°C ) – 50°C
VP – VN = 2.15 V
Figure 15. Accuracy Using Linear Transfer Function
3.0
150
2.5
125
2.0
Output Current (µA)
Temperature Accuracy (ƒC)
0
LMT01 Junction Temperaure (ƒC)
Figure 14. Accuracy Histogram at -50°C
1.5
1.0
0.5
0.0
High Level Current
100
75
Low Level Current
50
25
-0.5
-1.0
0
±50
±25
0
25
50
75
100
125
LMT01 Junction Temperaure (ƒC)
150
2
3
4
5
VP - VN (V)
C019
Using Temp = (PC/4096 × 256°C ) – 50°C
VP – VN = 5.5V
6
C004
TA = 30°C
Figure 16. Accuracy Using Linear Transfer Function
Figure 17. Output Current vs VP-VN Voltage
150
Percent of (Final - Initial) Value (%)
110
125
Output Current (µA)
±25
C020
High Level Current
100
75
Low Level Current
50
25
0
100
90
80
70
60
50
40
30
20
10
0
±50
±25
0
25
50
75
100
125
LMT01 Juntion Temperature (ƒC)
150
0
120 240 360 480 600 720 840 960 1080 1200
Time (seconds)
C003
VP – VN = 3.3 V
TINITIAL = 23°C,
VP – VN = 3.3 V
Figure 18. Output Current vs Temperature
C033
TFINAL = 70°C
Figure 19. Thermal Response in Still Air (TO92S/LPG
Package)
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
11
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
110
110
100
100
Percent of (Final - Initial) Value (%)
Percent of (Final - Initial) Value (%)
Typical Characteristics (continued)
90
80
70
60
50
40
30
20
10
0
80
70
60
50
40
30
20
10
0
0
20
40
60
80
100 120 140 160 180 200
Time (seconds)
VP – VN = 3.3 V
TINITIAL = 23°C,
TFINAL = 70°C
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0
Time (seconds)
C032
Air Flow = 2.34
meters/sec
Figure 20. Thermal Response in Moving Air (TO92S/LPG
Package)
12
90
VP – VN = 3.3 V
TINITIAL = 23°C,
C031
TFINAL = 70°C
Figure 21. Thermal Response in Stirred Oil (TO92S/LPG
Package)
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
7 Detailed Description
7.1 Overview
The LMT01 temperature output is transmitted over a single wire using a train of current pulses that typically
change from 34 µA to 125 µA. A simple resistor can then be used to convert the current pulses to a voltage. With
a 10-kΩ resistor, the output voltage levels range from 340 mV to 1.25 V, typically. A simple microcontroller
comparator or external transistor can be used convert this signal to valid logic levels the microcontroller can
process properly through a GPIO pin. The temperature can be determined by gating a simple counter on for a
specific time interval to count the total number of output pulses. After power is first applied to the device the
current level will remain below 34 µA for at most 54 ms while the LMT01 is determining the temperature. When
the temperature is determined, the pulse train begins. The individual pulse frequency is typically 88 kHz. The
LMT01 will continuously convert and transmit data when the power is applied approximately every 104 ms
(maximum).
The LMT01 uses thermal diode analog circuitry to detect the temperature. The temperature signal is then
amplified and applied to the input of a ΣΔ ADC that is driven by an internal reference voltage. The ΣΔ ADC
output is then processed through the interface circuitry into a digital pulse train. The digital pulse train is then
converted to a current pulse train by the output signal conditioning circuitry that includes high and low current
regulators. The voltage applied across the pins of the LMT01 is regulated by an internal voltage regulator to
provide a consistent Chip VDD that is used by the ADC and its associated circuitry.
7.2 Functional Block Diagram
VP
Chip VDD
Chip VSS
Thermal Diode
Analog Circuitry
Data
ADC
Interface
Voltage
Regulator
and
Output
Signal
Conditioning
VREF
LMT01
VN
7.3 Feature Description
7.3.1 Output Interface
The LMT01 provides a digital output in the form of a pulse count that is transmitted by a train of current pulses.
After the LMT01 is powered up, it transmits a very low current of 34 µA for less than 54 ms while the part
executes a temperature to digital conversion, as shown in Figure 22. When the temperature-to-digital conversion
is complete, the LMT01 starts to transmit a pulse train that toggles from the low current of 34 µA to a high current
level of 125 µA. The pulse train total time interval is at maximum 50 ms. The LMT01 transmits a series of pulses
equivalent to the pulse count at a given temperature as described in Electrical Characteristics - TO-92/LPG Pulse
Count to Temperature LUT. After the pulse count has been transmitted the LMT01 current level will remain low
for the remainder of the 50 ms. The total time for the temperature to digital conversion and the pulse train time
interval is 104 ms (maximum). If power is continuously applied, the pulse train output will repeat start every 104
ms (maximum).
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
13
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
Feature Description (continued)
Start of data
transmission
Power
ON
End of data
54ms
max
Start of next
conversion result data
End of data
104ms max
Power
50ms max
50ms max
Power
Off
Pulse
Train
Figure 22. Temperature to Digital Pulse Train Timing Cycle
The LMT01 can be powered down at any time to conserve system power. Take care to ensure that a minimum
power-down wait time of 50 ms is used before the device is turned on again.
7.3.2 Output Transfer Function
TheLMT01 outputs at minimum 1 pulse and a theoretical maximum 4095 pulses. Each pulse has a weight of
0.0625°C. One pulse corresponds to a temperature less than –50°C while a pulse count of 4096 corresponds to
a temperature greater than 200°C. Note that the LMT01 is only ensured to operate up to 150°C. Exceeding this
temperature by more than 5°C may damage the device. The accuracy of the device degrades as well when
150°C is exceeded.
Two different methods of converting the pulse count to a temperature value are discussed in this section. The
first method is the least accurate and uses a first order equation, and the second method is the most accurate
and uses linear interpolation of the values found in the look-up table (LUT) as described in Electrical
Characteristics - TO-92/LPG Pulse Count to Temperature LUT.
The output transfer function appears to be linear and can be approximated by Equation 1:
§ PC
·
Temp ¨
u 256qC ¸ 50qC
© 4096
¹
where
•
•
PC is the Pulse Count
Temp is the temperature reading
(1)
Table 1 shows some sample calculations using Equation 1.
Table 1. Sample Calculations Using Equation 1
14
TEMPERATURE (°C)
NUMBER OF PULSES
–49.9375
1
–49.875
2
–40
160
–20
480
0
800
30
1280
50
1600
100
2400
150
3200
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
The curve shown in Figure 23 shows the output transfer function using equation Equation 1 (blue line) and the
look-up table (LUT) found in Electrical Characteristics - TO-92/LPG Pulse Count to Temperature LUT (red line).
The LMT01 output transfer function as described by the LUT appears to be linear, but upon close inspection, it
can be seen as truly not linear. To actually see the difference, the accuracy obtained by the two methods must
be compared.
4096
3584
Pulse Count
3072
2560
2048
1536
1024
512
0
±50 ±25
0
25
50
75
100 125 150 175 200 225
LMT01 Junction Temperature (ƒC)
C002
Figure 23. LMT01 Output Transfer Function
For more exact temperature readings the output pulse count can be converted to temperature using linear
interpolation of the values found in Electrical Characteristics - TO-92/LPG Pulse Count to Temperature LUT.
3.0
1.0
2.5
0.8
Temperature Accuracy (ƒC)
Temperature Accuracy (ƒC)
The curves in Figure 24 and Figure 25, show the accuracy of typical units when using the Equation 1 and linear
interpolation using Electrical Characteristics - TO-92/LPG Pulse Count to Temperature LUT, respectively. When
compared, the improved performance when using the LUT linear interpolation method can clearly be seen. For a
limited temperature range of 25°C to 80°C, the error shown in Figure 24 is flat, so the linear equation will provide
good results. For a wide temperature range, TI recommends that linear interpolation and the LUT be used.
2.0
1.5
1.0
0.5
0.0
-0.5
Max Limit
0.6
0.4
0.2
0.0
-0.2
-0.4
-0.6
Min Limit
-0.8
-1.0
-1.0
±50
±25
0
25
50
75
100
125
LMT01 Junction Temperaure (ƒC)
150
±50
Figure 24. LMT01 Typical Accuracy When Using First
Order Equation Equation 1 – 92 Typical Units Plotted at
(VP – VN) = 2.15 V
±25
0
25
50
75
100
LMT01 Junction Temperaure (ƒC)
C018
125
150
C017
Figure 25. LMT01 Accuracy Using Linear Interpolation of
LUT Found In Electrical Characteristics - TO-92/LPG Pulse
Count to Temperature LUT – 92 typical units plotted at
(VP – VN) = 2.15 V
7.3.3 Current Output Conversion to Voltage
The minimum voltage drop across the LMT01 must be maintained at 2.15 V during the conversion cycle. After
the conversion cycle, the minimum voltage drop can decrease to 2.0 V. Thus the LMT01 can be used for low
voltage applications. See Application Information for more information on low voltage operation and other
information on picking the actual resistor value for different applications conditions. The resistor value is
dependent on the power supply level and the variation and the threshold level requirements of the circuitry the
resistor is driving (that is, MCU, GPIO, or Comparator).
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
15
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
Stray capacitance can be introduced when connecting the LMT01 through a long wire. This stray capacitance
influences the signal rise and fall times. The wire inductance has negligible effect on the AC signal integrity. A
simple RC time constant model as shown in Figure 26 can be used to determine the rise and fall times.
POWER
tHL
LMT01
VF
VHL
OUTPUT
C
100pF
34 and
125 µA
R
10k
VS
Figure 26. Simple RC Model for Rise and Fall Times
§ V VS ·
Ru Cu In ¨ F
¸
© VF VHL ¹
tHL
where
•
•
•
•
RC as shown in Figure 26
VHL is the target high level
the final voltage VF = 125 µA × R
the start voltage VS = 34 µA × R
(2)
For the 10% to 90% level rise time (tr), Equation 2 simplifies to:
tr = R×C×2.197
(3)
Take care to ensure that the LMT01 voltage drop does not exceed 300 mV under reverse bias conditions, as
given in the Absolute Maximum Ratings.
7.4 Device Functional Modes
The only functional mode the LMT01 has is that it provides a pulse count output that is directly proportional to
temperature.
16
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Mounting, Temperature Conductivity, and Self-Heating
The LMT01 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be
glued or cemented to a surface to ensure good temperature conductivity. The temperatures of the lands and
traces to the leads of the LMT01 also affect the temperature reading, so they must be a thin as possible.
Alternatively, the LMT01 can be mounted inside a sealed-end metal tube, and then can be dipped into a bath or
screwed into a threaded hole in a tank. As with any IC, the LMT01 and accompanying wiring and circuits must be
kept insulated and dry to avoid excessive leakage and corrosion. Printed-circuit coatings are often used to
ensure that moisture cannot corrode the leads or circuit traces.
The junction temperature of the LMT01 is the actual temperature being measured by the device. The thermal
resistance junction-to-ambient (RθJA) is the parameter (from Thermal Information) used to calculate the rise of a
device junction temperature (self-heating) due to its average power dissipation. The average power dissipation of
the LMT01 is dependent on the temperature it is transmitting as it effects the output pulse count and the voltage
across the device. Equation 4 is used to calculate the self-heating in the die temperature of the LMT01 (TSH).
ª§
tCONV
·
u VCONV ¸
ǬIOL u
tCONV tDATA
¹
¬«©
TSH
§ ª§ PC
tDATA
·º
I
I · § 4096 PC
u OL OH ¸ ¨
u IOL ¸» u
¨ «¨
¨ © 4096
2
¹ © 4096
¹¼ t CONV tDATA
©¬
º
·
¸ u VDATA » u RTJA
¸
¹
¼»
where
•
•
•
•
•
•
•
•
TSH is the ambient temperature
IOL and IOH are the output low and high current level, respectively
VCONV is the voltage across the LMT01 during conversion
VDATA is the voltage across the LMT01 during data transmission
tCONV is the conversion time
tDATA is the data transmission time
PC is the output pulse count
RθJA is the junction to ambient package thermal resistance
(4)
Plotted in the curve Figure 27 are the typical average supply current (black line using left y axis) and the resulting
self-heating (red and violet lines using right y axis) during continuous conversions. A temperature range of –50°C
to +150°C, a VCONV of 5 V (red line) and 2.15 V (violet line) were used for the self-heating calculation. As can be
seen in the curve, the average power supply current and thus the average self-heating changes linearly over
temperature because the number of pulses increases with temperature. A negligible self-heating of about 45m°C
is observed at 150°C with continuous conversions. If temperature readings are not required as frequently as
every 100 ms, self-heating can be minimized by shutting down power to the part periodically thus lowering the
average power dissipation.
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
17
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
60
0.06
50
0.05
40
0.04
30
0.03
20
0.02
10
0.01
Average Current
Self Heating at VP-VN=5V
Self Heating at VP-VN=2.15V
0
-100
-50
0
50
100
150
Self Heating (ƒC)
Average Current (µA)
Application Information (continued)
0.00
200
Temperature (ƒC)
C001
Figure 27. Average Current Draw and Self-Heating Over Temperature
8.2 Typical Application
8.2.1 3.3-V System VDD MSP430 Interface - Using Comparator Input
VDD 3.3V
MSP430
GPIO
Divider
VP
LMT01
VREF
2.73V
or
2.24V
TIMER2
VN
COMP_B
CLOCK
+
VR
IR = 34
and 125 µA
R
6.81k
1%
Figure 28. MSP430 Comparator Input Implementation
8.2.1.1 Design Requirements
The design requirements listed in are used in the detailed design procedure.
Table 2. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
VDD
3.3 V
VDD minimum
3.0 V
LMT01 VP – VN minimum during conversion
2.15 V
LMT01 VP – VN minimum during data
transmission
2.0 V
Noise margin
50 mV minimum
Comparator input current over temperature range
of interest
Resistor tolerance
18
< 1 uA
1%
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
8.2.1.2 Detailed Design Procedure
First, select the R and determine the maximum logic low voltage and the minimum logic high voltage while
ensuring that when the LMT01 is converting, the minimum (VP – VN) requirement of 2.15 V is met.
1. Select R using minimum VP-VN during data transmission (2 V) and maximum output current of the LMT01
(143.75 µA)
– R = (3.0 V – 2 V) / 143.75 µA = 6.993 k the closest 1% resistor is 6.980 k
– 6.993 k is the maximum resistance so if using 1% tolerance resistor the actual resistor value needs to be
1% less than 6.993 k and 6.98 k is 0.2% less than 6.993 k thus 6.81 k must be used.
2. Check to see if the 2.15-V minimum voltage during conversion requirement for the LMT01 is met with the
maximum IOL of 39 µA and maximum R of 6.81 k + 1%:
– VLMT01 = 3 V – (6.81 k × 1.01) × 39 µA = 2.73 V
3. Find the maximum low level voltage range using the maximum R of 6.81 k and maximum IOL of 39 µA:
– VRLmax = (6.81 k × 1.01) × 39 µA = 268 mV
4. Find the minimum high level voltage using the minimum R of 6.81 k and minimum IOH of 112.5 µA:
– VRHmin = (6.81 k × 0.99) × 112.5 µA = 758 mV
Now select the MSP430 comparator threshold voltage that enables the LMT01 to communicate to the MSP430
properly.
1. The MSP430 voltage is selected by selecting the internal VREF and then choosing the appropriate 1 of n/32
settings for n of 1 to 31.
– VMID= (VRLmax – VRHmin) / 2 + VRHmin = (758 mV – 268 mV) / 2 + 268 mV = 513 mV
– n = (VMID / VREF ) × 32 = (0.513 / 2.5) × 32 = 7
2. To prevent oscillation of the comparator, output hysteresis must be implemented. The MSP430 allows this by
enabling different n for the rising edge and falling edge of the comparator output. For a falling comparator
output transition, N must be set to 6.
3. Determine the noise margin caused by variation in comparator threshold level. Even though the comparator
threshold level theoretically is set to VMID, the actual level varies from device to device due to VREF tolerance,
resistor divider tolerance, and comparator offset. For proper operation, the COMP_B worst case input
threshold levels must be within the minimum high and maximum low voltage levels presented across R,
VRHmin and VRLmax, respectively
N N_TOL
VCHmax VREF u 1 V_REF_TOL u
COMP_OFFSET
32
where
•
•
•
•
•
VCLmin
VREF is the MSP430 COMP_B reference voltage for this example at 2.5 V
V_REF_TOL is the tolerance of the VREF of 1% or 0.01,
N is the divisor for the MSP430 or 7
N_TOL is the tolerance of the divisor or 0.5
COMP_OFFSET is the comparator offset specification or 10 mV
VREF u 1 V_REF_TOL u
N N_TOL
32
(5)
COMP_OFFSET
where
•
•
•
•
•
VREF is the MSP430 COMP_B reference voltage for this example at 2.5 V,
V_REF_TOL is the tolerance of the VREF of 1% or 0.01,
N is the divisor for the MSP430 for the hysteresis setting or 6,
N_TOL is the tolerance of the divisor or 0.5,
COMP_OFFSET is the comparator offset specification or 10 mV
(6)
The noise margin is the minimum of the two differences:
(VRHmin – VCHmax) or (VCHmin – VRLmax)
(7)
which works out to be 145 mV.
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
19
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
Comparator Threshold and VR
VDD
Pulse
Count
Signal
VRHmax
VRHmin
Noise Margin
VCHmax
VMID
VCHmin
Noise Margin
VRLmax
VRLmin
GND
Time (µs)
Figure 29. Pulse Count Signal Amplitude Variation
8.2.1.2.1 Setting the MSP430 Threshold and Hysteresis
The comparator hysteresis determines the noise level that the signal can support without causing the comparator
to trip falsely and resulting in an inaccurate pulse count. The comparator hysteresis is set by the precision of the
MSP430 and what thresholds it is capable of. For this case, as the input signal transitions high, the comparator
threshold is dropped by 77 mV. If the noise on the signal is kept below this level as it transitions, the comparator
will not trip falsely. In addition, the MSP430 has a digital filter on the COMP_B output that be used to further filter
output transitions that occur too quickly.
8.2.1.3 Application Curves
Amplitude = 200 mV/div
Time Base = 10 µs/div
Δy at cursors = 500 mV
Δx at cursors = 11.7 µs
Figure 30. MSP430 COMP_B Input Signal No Capacitance
Load
Amplitude = 200 mV/div
Time Base = 10 µs/div
Δy at cursors = 484 mV
Δx at cursors = 11.7 µs
Figure 31. MSP430 COMP_B Input Signal 100-pF
Capacitance Load
8.3 System Examples
The LMT01 device can be configured in a number of ways. Transistor level shifting can be used so that the
output pulse of the device can be read with a GPIO (see Figure 32). An isolation block can be inserted to
achieve electrical isolation (see Figure 33). Multiple LMT01 devices can be controlled with GPIOs enabling
temperature monitor for multiple zones. Lastly, the LMT01 device can be configured to have a common ground
with a high side signal (see Figure 35).
20
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
System Examples (continued)
3.3V
VDD
MCU/
FPGA/
ASIC
VP
LMT01
100k
VN
GPIO
MMBT3904
34 and
125 µA
7.5k
Figure 32. Transistor Level Shifting
3V to 5.5V
3V to 5.5V
ISO734x
VCC1
VCC2
VDD
VP
ISOLATION
LMT01
MCU/FPGA/
ASIC
Min
2.0V
100k
VN
GPIO
MMBT3904
34 and
125 µA
7.5k
GND2
GND1
Figure 33. Isolation
VDD
3V to 5.5V
GPIO1
GPIO2
GPIO n
Up to 2.0m
VP
VP
VP
LMT01
U1
LMT01
U2
LMT01
Un
VN
VN
VN
MCU/FPGA/
ASIC
Min
2.0V
GPIO/
COMP
34 and
125 µA
6.81k
(for 3V)
Note: to turn off an LMT01 set the GPIO pin connected to VP to high impedance state as setting it low would cause
the off LMT01 to be reverse biased. Comparator input of MCU must be used.
Figure 34. Connecting Multiple Devices to One MCU Input Pin
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
21
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
System Examples (continued)
3.3V
VDD
34 and
125 µA
7.5k
MCU/
FPGA/
ASIC
MMBT3906
VP
LMT01
GPIO
VN
100k
Note: the VN of the LMT01 must be connected to the MCU GND.
Figure 35. Common Ground With High-Side Signal
9 Power Supply Recommendations
Because the LMT01 is only a 2-pin device the power pins are common with the signal pins, thus the LMT01 has
a floating supply that can vary greatly. The LMT01 has an internal regulator that provides a stable voltage to
internal circuitry.
Take care to prevent reverse biasing of the LMT01 as exceeding the absolute maximum ratings may cause
damage to the device.
Power supply ramp rate can effect the accuracy of the first result transmitted by the LMT01. As shown in
Figure 36 with a 1-ms rise time, the LMT01 output code is at 1286, which converts to 30.125°C. The scope photo
shown in Figure 37 reflects what happens when the rise time is too slow. In Figure 37, the power supply (yellow
trace) is still ramping up to final value while the LMT01 (red trace) has already started a conversion. This causes
the output pulse count to decrease from the previously shown 1286, to 1282 (or 29.875°C). Thus, for slow ramp
rates, TI recommends that the first conversion be discarded. For even slower ramp rates, more than one
conversion may have to be discarded as TI recommends that either the power supply be within final value before
a conversion is used or that ramp rates be faster than 2.5 ms.
Yellow trace = 1 V/div, Red trace = 100 mV/div, Time Base = 20
ms/div
TA= 30°C
LMT01 Pulse Count = 1286
VP-VN = 3.3 V
Rise Time = 1 ms
Figure 36. Output Pulse Count With Appropriate Power
Supply Rise Time
22
Yellow trace = 1V/div, Red trace = 100 mV/div, Time base = 20
ms/div
TA=30°C
LMT01 Pulse Count = 1282
VP-VN=3.3 V
Rise Time = 100 ms
Figure 37. Output Pulse Count With Slow Power Supply
Rise Time
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
LMT01
www.ti.com
SNIS189D – JUNE 2015 – REVISED JUNE 2018
10 Layout
10.1 Layout Guidelines
The LMT01 can be mounted to a PCB as shown in Figure 38 and Figure 39. Take care to make the traces
leading to the pads as small as possible to minimize their effect on the temperature the LMT01 is measuring.
10.2 Layout Example
VP
VN
Figure 38. Layout Example (TO92S/LPG Package)
VN
VP
Figure 39. Layout Example for the DQX (WSON) Package
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
23
LMT01
SNIS189D – JUNE 2015 – REVISED JUNE 2018
www.ti.com
11 Device and Documentation Support
11.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
24
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
Product Folder Links: LMT01
PACKAGE OPTION ADDENDUM
www.ti.com
23-Apr-2019
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMT01DQXR
ACTIVE
WSON
DQX
2
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-50 to 150
13N
LMT01DQXT
ACTIVE
WSON
DQX
2
250
Green (RoHS
& no Sb/Br)
CU
Level-1-260C-UNLIM
-50 to 150
13N
LMT01LPG
ACTIVE
TO-92
LPG
2
1000
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
-50 to 150
LMT01
LMT01LPGM
ACTIVE
TO-92
LPG
2
3000
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
-50 to 150
LMT01
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
23-Apr-2019
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMT01 :
• Automotive: LMT01-Q1
• Space: LMT01-SP
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-May-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LMT01DQXR
WSON
DQX
2
3000
180.0
8.4
2.0
2.8
1.0
4.0
8.0
Q1
LMT01DQXT
WSON
DQX
2
250
180.0
8.4
2.0
2.8
1.0
4.0
8.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-May-2018
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMT01DQXR
WSON
DQX
2
3000
203.0
203.0
35.0
LMT01DQXT
WSON
DQX
2
250
203.0
203.0
35.0
Pack Materials-Page 2
GENERIC PACKAGE VIEW
DQX 2
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
1.7 x 2.5, 0 mm pitch
This image is a representation of the package family, actual package may vary.
Refer to the product data sheet for package details.
4225319/A
www.ti.com
PACKAGE OUTLINE
DQX0002A
WSON - 0.8 mm max height
SCALE 5.200
PLASTIC SMALL OUTLINE - NO LEAD
1.75
1.65
A
B
PIN 1 INDEX AREA
2.55
2.45
C
0.8 MAX
SEATING PLANE
0.05
0.00
(0.2) TYP
(0.45)
4X
0.3
0.2
2X 0.1 MIN
2
(0.15)
2X (0.05)
SYMM
PIN 1 ID
(45 X0.2)
1.1
0.9
1
SYMM
(0.2) TYP
0.8
0.6
0.1
C A B
4222491/E 03/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
DQX0002A
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(0.7)
SYMM
1
(1.2)
SYMM
(1.7)
2
(0.25)
(0.35)
(R0.05) TYP
4X (0.25)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:30X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL EDGE
METAL UNDER
SOLDER MASK
EXPOSED
METAL
EXPOSED
METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4222491/E 03/2019
NOTES: (continued)
3. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271).
4. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown on this view.
It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
DQX0002A
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(0.225) TYP
1
(1.225)
TYP
2X (0.6)
(0.55)
SYMM
2X (0.7)
(0.15)
4X (0.45)
(R0.05) TYP
2
4X (0.25)
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
81% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
SCALE:30X
4222491/E 03/2019
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
PACKAGE OUTLINE
LPG0002A
TO-92 - 5.05 mm max height
SCALE 1.300
TO-92
4.1
3.9
3.25
3.05
3X
2.3
2.0
2
1
0.51
0.40
5.05
MAX
2 MAX
6X 0.076 MAX
2X
15.5
15.1
3X
0.48
0.33
3X
2X 1.27 0.05
0.51
0.33
2.64
2.44
2.68
2.28
1.62
1.42
2X (45° )
(0.55)
1
2
0.86
0.66
4221971/A 03/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
LPG0002A
TO-92 - 5.05 mm max height
TO-92
0.05 MAX
ALL AROUND
TYP
(1.07)
METAL
TYP
3X ( 0.75) VIA
(1.7)
(R0.05) TYP
SOLDER MASK
OPENING
TYP
(1.7)
2
1
(1.27)
(1.07)
(2.54)
LAND PATTERN EXAMPLE
NON-SOLDER MASK DEFINED
SCALE:20X
4221971/A 03/2015
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising