Texas Instruments | TMP75B 1.8-V Digital Temperature Sensor with Two-Wire Interface and Alert (Rev. B) | Datasheet | Texas Instruments TMP75B 1.8-V Digital Temperature Sensor with Two-Wire Interface and Alert (Rev. B) Datasheet

Texas Instruments TMP75B 1.8-V Digital Temperature Sensor with Two-Wire Interface and Alert (Rev. B) Datasheet
Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
TMP75B 1.8-V Digital Temperature Sensor with Two-Wire Interface and Alert
1 Features
3 Description
•
•
The TMP75B is an integrated digital temperature
sensor with a 12-bit analog-to-digital converter (ADC)
that can operate at a 1.8-V supply, and is pin and
register compatible with the industry-standard LM75
and TMP75. This device is available in SOIC-8 and
VSSOP-8 packages, and requires no external
components to sense the temperature. The TMP75B
is capable of reading temperatures with a resolution
of 0.0625°C and is specified over a temperature
range of –55°C to +125°C.
1
•
•
•
•
•
•
•
•
•
•
Low-Voltage Alternative to LM75 and TMP75
Digital Output with Standard Two-Wire Serial
Interface
Up to 8 Pin-Programmable Bus Addresses
Overtemperature ALERT Pin with Programmable
Trip Values
Shutdown Mode for Battery Power Saving
One-Shot Conversion Mode for Custom Update
Rates
Operating Temperature Range: –55°C to +125°C
Operating Supply Range: 1.4 V to 3.6 V
Quiescent Current:
– 45 μA Active (typ)
– 0.3 μA Shutdown (typ)
Accuracy:
– ±0.5°C (typ) from –20°C to +85°C
– ±1°C (typ) from –55°C to +125°C
Resolution: 12 Bits (0.0625°C)
Packages: SOIC-8 and VSSOP-8
2 Applications
•
•
•
•
•
•
•
•
•
The TMP75B features SMBus and two-wire interface
compatibility, and allows up to eight devices on the
same bus with the SMBus overtemperature alert
function. The programmable temperature limits and
the ALERT pin allow the sensor to operate as a
stand-alone thermostat, or an overtemperature alarm
for power throttling or system shutdown.
The factory-calibrated temperature accuracy and the
noise-immune digital interface make the TMP75B the
preferred solution for temperature compensation of
other sensors and electronic components, without the
need for additional system-level calibration or
elaborate board layout for distributed temperature
sensing.
The TMP75B is ideal for thermal management and
protection of a variety of consumer, computer,
communication,
industrial,
and
environmental
applications.
Server and Computer Thermal Management
Telecommunication Equipment
Office Machines
Video Game Consoles
Set-Top Boxes
Power Supply and Battery Thermal Protection
Thermostat Control
Environmental Monitoring and HVAC
Electrical Motor Driver Thermal Protection
Device Information(1)
DEVICE NAME
TMP75B
PACKAGE
BODY SIZE (NOM)
SOIC (8)
4.90 mm × 3.90 mm
VSSOP (8)
3.00 mm × 3.00 mm
(1) For all available packages, see the package option addendum
at the end of the datasheet.
Temperature Accuracy (Error) vs Ambient
Temperature
Simplified Schematic
1.4 V to 3.6 V
3
TMP75B
1
2
Two-Wire
Host Controller
3
SDA
VS
SCL
A0
ALERT
A1
8
7
6
Temperature Error (ƒC)
2
0.01 PF
1
0
±1
Mean
±2
4
GND
A2
Mean - 61
5
Mean + 61
±3
±75
±50
±25
0
25
50
75
Temperature (ƒC)
100
125
150
C005
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
6
Absolute Maximum Ratings ......................................
Handling Ratings.......................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 7
7.1 Overview ................................................................... 7
7.2 Functional Block Diagram ......................................... 7
7.3 Feature Description................................................... 8
7.4 Device Functional Modes........................................ 15
7.5 Programming........................................................... 16
7.6 Register Map........................................................... 16
8
Application and Implementation ........................ 19
8.1 Application Information............................................ 19
8.2 Typical Application ................................................. 19
9 Power Supply Recommendations...................... 20
10 Layout................................................................... 21
10.1 Layout Guidelines ................................................. 21
10.2 Layout Example .................................................... 21
11 Device and Documentation Support ................. 22
11.1
11.2
11.3
11.4
Documentation Support .......................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
22
22
22
22
12 Mechanical, Packaging, and Orderable
Information ........................................................... 22
4 Revision History
Changes from Revision A (April 2014) to Revision B
•
Added DGK (VSSOP-8) package to data sheet .................................................................................................................... 1
Changes from Original (April 2014) to Revision A
•
2
Page
Page
Changed from product preview to production data ................................................................................................................ 1
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
5 Pin Configuration and Functions
D and DGK Packages
SOIC-8 and VSSOP-8
(Top View)
SDA
1
8
VS
SCL
2
7
A0
ALERT
3
6
A1
GND
4
5
A2
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
A0
7
I
Address select. Connect to GND or VS.
A1
6
I
Address select. Connect to GND or VS.
A2
5
I
Address select. Connect to GND or VS.
ALERT
3
O
Overtemperature alert. Open-drain output; requires a pull-up resistor.
GND
4
—
Ground.
SCL
2
I
SDA
1
I/O
VS
8
I
Serial clock.
Serial data. Open-drain output; requires a pull-up resistor.
Supply voltage, 1.4 V to 3.6 V.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
3
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1)
MIN
MAX
UNIT
4
V
V
Supply voltage, VS
Input voltage
Sink current
SDA, SCL, ALERT, A2, A1
-0.3
4
A0
-0.3
(VS) + 0.3
V
10
mA
150
°C
SDA, ALERT
Operating junction temperature
(1)
-55
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 Handling Ratings
MIN
Tstg
Storage temperature range
V(ESD)
(1)
Electrostatic Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins
discharge
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins (2)
(1)
(2)
MAX
UNIT
°C
-60
150
–2000
2000
–1000
1000
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
Supply voltage
1.4
1.8
Operating free-air temperature, TA
-55
MAX
UNIT
3.6
V
125
°C
6.4 Thermal Information
TMP75B
THERMAL METRIC (1)
D (SOIC)
DGK (VSSOP)
8 PINS
8 PINS
188.1
RθJA
Junction-to-ambient thermal resistance
125.4
RθJC(top)
Junction-to-case (top) thermal resistance
71.5
79.1
RθJB
Junction-to-board thermal resistance
65.8
109.6
ψJT
Junction-to-top characterization parameter
21.1
15.3
ψJB
Junction-to-board characterization parameter
65.3
108
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
N/A
(1)
4
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
6.5 Electrical Characteristics
At TA = –55°C to +125°C and VS = +1.4 V to +3.6 V, unless otherwise noted. Typical values at TA = 25°C and VS = +1.8 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
+125
°C
TEMPERATURE INPUT
Temperature range
–55
Temperature resolution
Temperature accuracy
(error)
0.0625
–20°C to +85°C
°C
±0.5
±2
°C
±1
±3
°C
0.7(VS)
VS
V
-0.3
0.3(VS)
V
1
μA
0.4
V
–55°C to +125°C
DIGITAL INPUT/OUTPUT
VIH
High-level input voltage
VIL
Low-level input voltage
IIN
Input current
0 V < VIN < (VS) + 0.3 V
VOL
Low-level output
voltage
VS ≥ 2 V, IOUT = 3 mA
VS < 2 V, IOUT = 3 mA
0.2(VS)
ADC resolution
Conversion time
Conversion modes
V
12
One-shot mode
20
27
Bit
35
ms
CR1 = 0, CR0 = 0 (default)
37
Conv/s
CR1 = 0, CR0 = 1
18
Conv/s
CR1 = 1, CR0 = 0
9
Conv/s
CR1 = 1, CR0 = 1
4
Conv/s
Timeout time
38
54
70
ms
3.6
V
POWER SUPPLY
Operating supply range
IQ
ISD
Quiescent current
Shutdown current
1.4
Serial bus inactive, CR1 = 0, CR0 = 0 (default)
45
89
μA
Serial bus inactive, CR1 = 0, CR0 = 1
22
48
μA
Serial bus inactive, CR1 = 1, CR0 = 0
12
30
μA
Serial bus inactive, CR1 = 1, CR0 = 1
6.5
21
μA
Serial bus inactive
0.3
8
μA
Serial bus active, SCL frequency = 400 kHz
10
μA
Serial bus active, SCL frequency = 3.4 MHz
80
μA
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
5
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
6.6 Typical Characteristics
At TA = 25°C and VS = +1.8 V (unless otherwise noted).
100
80
70
Vs = 1.4V
9
Vs = 1.8V
8
Vs = 3.6V
7
60
ISD (A)
IQ (A)
10
CR = '0h'
CR = '1h'
CR = '2h'
CR = '3h'
90
50
40
6
5
4
30
3
20
2
10
1
0
0
±75
±50
±25
0
25
50
75
100
125
±75
150
Temperature (ƒC)
±25
0
25
50
75
100
125
150
Temperature (ƒC)
Figure 1. Quiescent Current vs Temperature
C002
Figure 2. Shutdown Current vs Temperature
30
200
29
175
28
Ta = -Û&
7D Û&
7D Û&
150
27
125
26
IQ (A)
Conversion Time (ms)
±50
C001
25
24
100
75
23
22
21
Vs = 1.4V
50
Vs = 1.8V
25
Vs = 3.6V
20
±75
±50
±25
0
25
50
75
100
125
Temperature (ƒC)
0
150
10
Figure 3. Conversion Time vs Temperature
100
1000
10000
Bus Frequency (kHz)
C003
C004
Figure 4. Quiescent Current vs Bus Frequency
3
Population
1
0
±1
Mean
±2
Mean - 61
Mean + 61
±3
±75
±50
±25
0
25
50
75
100
125
Temperature (ƒC)
150
-1
-0.9
-0.8
-0.7
-0.6
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Temperature Error (ƒC)
2
C005
Temperature Error (ƒC)
C006
Figure 5. Temperature Error vs Temperature
6
Submit Documentation Feedback
Figure 6. Temperature Error at 25°C
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
7 Detailed Description
7.1 Overview
The TMP75B is a digital temperature sensor optimal for thermal management and thermal protection
applications. The TMP75B is two-wire and SMBus interface compatible, and is specified over a temperature
range of –55°C to +125°C.
The temperature sensing device for the TMP75B is the chip itself. A bipolar junction transistor (BJT) inside the
chip is used in a band-gap configuration to produce a voltage proportional to the chip temperature. The voltage is
digitized and converted to a 12-bit temperature result in degrees Celsius, with a resolution of 0.0625°C. The
package leads provide the primary thermal path because of the lower thermal resistance of the metal. Thus, the
temperature result is equivalent to the local temperature of the printed circuit board (PCB) where the sensor is
mounted.
7.2 Functional Block Diagram
VS
Device
Voltage Regulator
Register Bank
Oscillator
SDA
Serial Interface
Control Logic
SCL
A0
NxI
I
ALERT
A1
A2
ADC
Thermal
BJT
GND
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
7
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
7.3 Feature Description
7.3.1 Digital Temperature Output
The 12-bit digital output from each temperature measurement conversion is stored in the read-only temperature
register. Two bytes must be read to obtain the data, as shown in Figure 15. Note that byte 1 is the most
significant byte, followed by byte 2, the least significant byte. The temperature result is left-justified with the 12
most significant bits used to indicate the temperature. There is no need to read the second byte if resolution
below 1°C is not required. Table 1 summarizes the temperature data format. One LSB equals 0.0625°C.
Negative numbers are represented in binary twos complement format.
Table 1. Temperature Data Format (1)
DIGITAL OUTPUT
(1)
TEMPERATURE (°C)
BINARY
HEX
128
0111 1111 1111
7FF
127.9375
0111 1111 1111
7FF
100
0110 0100 0000
640
80
0101 0000 0000
500
75
0100 1011 0000
4B0
50
0011 0010 0000
320
25
0001 1001 0000
190
0.25
0000 0000 0100
004
0
0000 0000 0000
000
–0.25
1111 1111 1100
FFC
–25
1110 0111 0000
E70
–55
1100 1001 0000
C90
The temperature sensor resolution is 0.0625°C/LSB.
Table 1 does not supply a full list of all temperatures. Use the following rules to obtain the digital data format for
a given temperature, and vice versa.
To convert positive temperatures to a digital data format:
Divide the temperature by the resolution. Then, convert the result to binary code with a 12-bit, left-justified
format, and MSB = 0 to denote a positive sign.
Example: (+50°C) / (0.0625°C / LSB) = 800 = 320h = 0011 0010 0000
To convert a positive digital data format to temperature:
Convert the 12-bit, left-justified binary temperature result, with the MSB = 0 to denote a positive sign, to a
decimal number. Then, multiply the decimal number by the resolution to obtain the positive temperature.
Example: 0011 0010 0000 = 320h = 800 × (0.0625°C / LSB) = +50°C
To convert negative temperatures to a digital data format:
Divide the absolute value of the temperature by the resolution, and convert the result to binary code with a
12-bit, left-justified format. Then, generate the twos complement of the result by complementing the binary
number and adding one. Denote a negative number with MSB = 1.
Example: (|–25°C|) / (0.0625°C / LSB) = 400 = 190h = 0001 1001 0000
Two's complement format: 1110 0110 1111 + 1 = 1110 0111 0000
To convert a negative digital data format to temperature:
Generate the twos compliment of the 12-bit, left-justified binary number of the temperature result (with MSB
= 1, denoting negative temperature result) by complementing the binary number and adding one. This
represents the binary number of the absolute value of the temperature. Convert to decimal number and
multiply by the resolution to get the absolute temperature, then multiply by –1 for the negative sign.
Example: 1110 0111 0000 has twos compliment of 0001 1001 0000 = 0001 1000 1111 + 1
Convert to temperature: 0001 1001 0000 = 190h = 400; 400 × (0.0625°C / LSB) = 25°C = (|–25°C|);
(|–25°C|) × (–1) = –25°C
8
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
7.3.2 Temperature Limits and Alert
The temperature limits are stored in the TLOW and THIGH registers (Table 8 and Table 9) in the same format as
the temperature result, and their values are compared to the temperature result on every conversion. The
outcome of the comparison drives the behavior of the ALERT pin, which can operate as a comparator output or
an interrupt, and is set by the TM bit in the configuration register (Table 7).
In comparator mode (TM = 0, default), the ALERT pin becomes active when the temperature is equal to or
exceeds the value in THIGH (fault conditions) for a consecutive number of conversions as set by the FQ bits of the
configuration register. ALERT clears when the temperature falls below TLOW for the same consecutive number of
conversions. The difference between the two limits acts as a hysteresis on the comparator output, and a fault
counter prevents false alerts as a result of environmental noise.
In interrupt mode (TM = 1), the ALERT pin becomes active when the temperature equals or exceeds the value in
THIGH for a consecutive number of fault conditions. The ALERT pin remains active until a read operation of any
register occurs, or the device successfully responds to the SMBus alert response address. The ALERT pin is
also cleared if the device is placed in shutdown mode (see Shutdown Mode section for shutdown mode
description). After the ALERT pin is cleared, this pin becomes active again only when the temperature falls below
TLOW for a consecutive number of fault conditions, and remains active until cleared by a read operation of any
register, or a successful response to the SMBus alert response address. After the ALERT pin is cleared, the
cycle repeats with the ALERT pin becoming active when the temperature equals or exceeds THIGH, and so on.
The ALERT pin can also be cleared by resetting the device with the general-call reset command. This action also
clears the state of the internal registers in the device and the fault counter memory, returning the device to
comparator mode (TM = 0).
The active state of the ALERT pin is set by the POL bit in the configuration register. When POL = 0 (default), the
ALERT pin is active low. When POL = 1, the ALERT pin is active high. The operation of the ALERT pin in
various modes is illustrated in Figure 7.
THIGH
Measured
Temperature
TLOW
Device ALERT PIN
(Comparator Mode)
POL = 0
Device ALERT PIN
(Interrupt Mode)
POL = 0
Device ALERT PIN
(Comparator Mode)
POL = 1
Device ALERT PIN
(Interrupt Mode)
POL = 1
Read
Read
Read
Time
Figure 7. ALERT Pin Modes of Operation
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
9
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
7.3.3 Serial Interface
The TMP75B operates as a slave device only on the two-wire bus and SMBus. Connections to the bus are made
using the open-drain I/O lines, SDA and SCL. The SDA and SCL pins feature integrated spike-suppression filters
and Schmitt triggers to minimize the effects of input spikes and bus noise. The TMP75B supports the
transmission protocol for both fast (1 kHz to 400 kHz) and high-speed (1 kHz to 3 MHz) modes. All data bytes
are transmitted MSB first.
7.3.3.1 Bus Overview
The device that initiates the transfer is called a master, and the devices controlled by the master are slaves. The
bus must be controlled by a master device that generates the serial clock (SCL), controls the bus access, and
generates the start and stop conditions.
To address a specific device, initiate a start condition by pulling the data line (SDA) from a high to a low logic
level while SCL is high. All slaves on the bus shift in the slave address byte; the last bit indicates whether a read
or write operation follows. During the ninth clock pulse, the slave being addressed responds to the master by
generating an acknowledge bit and pulling SDA low.
Data transfer is then initiated and sent over eight clock pulses followed by an acknowledge bit. During data
transfer, SDA must remain stable while SCL is high because any change in SDA while SCL is high is interpreted
as a start or stop signal.
After all data have been transferred, the master generates a stop condition indicated by pulling SDA from low to
high, while SCL is high.
7.3.3.2 Serial Bus Address
To communicate with the TMP75B, the master must first communicate with slave devices using a slave address
byte. The slave address byte consists of seven address bits, and a direction bit indicating the intent of executing
either a read or write operation. The TMP75B features three address pins that allow up to eight devices to be
addressed on a single bus. The TMP75B latches the status of the address pins at the start of a communication.
Table 2 describes the pin logic levels and the corresponding address values.
Table 2. Address Pin Connections and Slave Addresses
DEVICE TWO-WIRE ADDRESS
A2
A1
A0
1001000
GND
GND
GND
1001001
GND
GND
VS
1001010
GND
VS
GND
1001011
GND
VS
VS
1001100
VS
GND
GND
1001101
VS
GND
VS
1001110
VS
VS
GND
1001111
VS
VS
VS
7.3.3.3 Writing and Reading Operation
Accessing a particular register on the TMP75B is accomplished by writing the appropriate value to the pointer
register. The value for the pointer register is the first byte transferred after the slave address byte with the R/W
bit low. Every write operation to the TMP75B requires a value for the pointer register (see Figure 9).
When reading from the TMP75B, the last value stored in the pointer register by a write operation is used to
determine which register is read by a read operation. To change the register pointer for a read operation, a new
value must be written to the pointer register. This action is accomplished by issuing a slave address byte with the
R/W bit low, followed by the pointer register byte. No additional data are required. The master can then generate
a start condition and send the slave address byte with the R/W bit high to initiate the read command. See
Figure 10 for details of this sequence. If repeated reads from the same register are desired, there is no need to
continually send the pointer register bytes because the TMP75B stores the pointer register value until it is
changed by the next write operation.
Note that register bytes are sent with the most significant byte first, followed by the least significant byte.
10
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
7.3.3.4 Slave-Mode Operations
The TMP75B can operate as a slave receiver or slave transmitter.
7.3.3.4.1 Slave Receiver Mode:
The first byte transmitted by the master is the slave address, with the R/W bit low. The TMP75B then
acknowledges reception of a valid address. The next byte transmitted by the master is the pointer register. The
TMP75B then acknowledges reception of the pointer register byte. The next byte or bytes are written to the
register addressed by the pointer register. The TMP75B acknowledges reception of each data byte. The master
can terminate data transfer by generating a start or stop condition.
7.3.3.4.2 Slave Transmitter Mode:
The first byte transmitted by the master is the slave address, with the R/W bit high. The slave acknowledges
reception of a valid slave address. The next byte is transmitted by the slave and is the most significant byte of
the register indicated by the pointer register. The master acknowledges reception of the data byte. The next byte
transmitted by the slave is the least significant byte. The master acknowledges reception of the data byte. The
master can terminate data transfer by generating a not-acknowledge bit on reception of any data byte, or by
generating a start or stop condition.
7.3.3.5 SMBus Alert Function
The TMP75B supports the SMBus alert function. When the TMP75B operates in interrupt mode (TM = 1), the
ALERT pin may be connected as an SMBus alert signal. When a master senses that an alert condition is present
on the ALERT line, the master sends an SMBus alert command (00011001) to the bus. If the ALERT pin is
active, the device acknowledges the SMBus alert command and responds by returning its slave address on the
SDA line. The eighth bit (LSB) of the slave address byte indicates whether the alert condition is caused by the
temperature exceeding THIGH or falling below TLOW. The LSB is high if the temperature is greater than THIGH, or
low if the temperature is less than TLOW. See Figure 11 for details of this sequence.
If multiple devices on the bus respond to the SMBus alert command, arbitration during the slave address portion
of the SMBus alert command determines which device clears its alert status first. If the TMP75B wins the
arbitration, its ALERT pin becomes inactive at the completion of the SMBus alert command. If the TMP75B loses
the arbitration, its ALERT pin remains active.
7.3.3.6 General Call
The TMP75B responds to a two-wire general call address (0000000) if the eighth bit is 0. The device
acknowledges the general call address and responds to commands in the second byte. If the second byte is
00000100, the TMP75B latches the status of the address pin, but does not reset. If the second byte is 00000110,
the TMP75B internal registers are reset to power-up values.
7.3.3.7 High-Speed (Hs) Mode
In order for the two-wire bus to operate at frequencies above 400 kHz, the master device must issue an SMBus
Hs-mode master code (00001xxx) as the first byte after a start condition to switch the bus to high-speed
operation. The TMP75B does not acknowledge this byte, but does switch its input filters on SDA and SCL and its
output filters on SDA to operate in Hs-mode, allowing transfers at up to 3 MHz. After the Hs-mode master code
has been issued, the master transmits a two-wire slave address to initiate a data-transfer operation. The bus
continues to operate in Hs-mode until a stop condition occurs on the bus. Upon receiving the stop condition, the
TMP75B switches the input and output filters back to fast-mode operation.
7.3.3.8 Timeout Function
The TMP75B resets the serial interface if SCL or SDA are held low for 54 ms (typ) between a start and stop
condition. If the TMP75B is pulled low, it releases the bus and then waits for a start condition. To avoid activating
the timeout function, it is necessary to maintain a communication speed of at least 1 kHz for the SCL operating
frequency.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
11
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
7.3.3.9 Two-Wire Timing
The TMP75B is two-wire and SMBus compatible. Figure 8 to Figure 11 describe the various operations on the
TMP75B. Parameters for Figure 8 are defined in Table 3. Bus definitions are:
Bus Idle
Both SDA and SCL lines remain high.
Start Data Transfer A change in the state of the SDA line, from high to low, while the SCL line is high defines a
start condition. Each data transfer is initiated with a start condition.
Stop Data Transfer A change in the state of the SDA line from low to high while the SCL line is high defines a
stop condition. Each data transfer is terminated with a repeated start or stop condition.
Data Transfer The number of data bytes transferred between a start and a stop condition is not limited, and is
determined by the master device.
The receiver acknowledges the transfer of data. It is also possible to use the TMP75B for
single-byte updates. To update only the MS byte, terminate communication by issuing a start
or stop condition on the bus.
Acknowledge Each receiving device, when addressed, must generate an acknowledge bit.
A device that acknowledges must pull down the SDA line during the acknowledge clock
pulse so that the SDA line is stable low during the high period of the acknowledge clock
pulse. Setup and hold times must be taken into account. When a master receives data, the
termination of the data transfer can be signaled by the master generating a not-acknowledge
(1) on the last byte transmitted by the slave.
Table 3. Timing Diagram Requirements
FAST MODE
SYMBOL
f(SCL)
PARAMETER
SCL operating frequency
HIGH-SPEED MODE
MIN
MAX
MIN
MAX
UNIT
VS ≥ 1.8 V
0.001
0.4
VS < 1.8 V
0.001
0.4
0.001
3
MHz
0.001
2.5
VS ≥ 1.8 V
1300
160
MHz
ns
VS < 1.8 V
1300
260
ns
t(BUF)
Bus free time between
stop and start conditions
t(HDSTA)
Hold time after repeated start condition.
After this period, the first clock is generated.
600
160
ns
t(SUSTA)
Repeated start condition setup time
600
160
ns
t(SUSTO)
Stop condition setup time
600
t(HDDAT)
Data hold time
t(SUDAT)
Data setup time
160
ns
VS ≥ 1.8 V
0
900
0
100
ns
VS < 1.8 V
0
900
0
140
ns
VS ≥ 1.8 V
100
10
ns
VS < 1.8 V
100
20
ns
VS ≥ 1.8 V
1300
190
ns
VS < 1.8 V
1300
240
ns
t(LOW)
SCL clock low period
t(HIGH)
SCL clock high period
tR(SDA), tF(SDA)
Data rise and fall time
300
80
ns
tR(SCL), tF(SCL)
Clock rise and fall time
300
40
ns
tR
Clock and data rise time for SCLK ≤ 100 kHz
12
600
Submit Documentation Feedback
60
1000
ns
ns
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
7.3.3.10 Two-Wire Timing Diagrams
t(LOW)
tF
tR
t(HDSTA)
SCL
t(HDSTA)
t(HIGH)
t(SUSTO)
t(SUSTA)
t(HDDAT)
t(SUDAT)
SDA
t(BUF)
P
S
S
P
Figure 8. Two-Wire Timing Diagram
1
9
1
9
SCL
¼
1
SDA
0
0
1
A2(1)
A1(1)
A0(1)
R/W
Start By
Master
0
0
0
0
0
0
P1
P0
ACK By
Device
¼
ACK By
Device
Frame 2 Pointer Register Byte
Frame 1 Two-Wire Slave Address Byte
9
1
1
9
SCL
(Continued)
SDA
(Continued)
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
ACK By
Device
D0
ACK By
Device
Stop By
Master
Frame 4 Data Byte 2
Frame 3 Data Byte 1
(1)
D1
The value of A0, A1, and A2 are determined by the connections of the corresponding pins.
Figure 9. Two-Wire Timing Diagram for Write Word Format
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
13
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
1
9
1
9
SCL
¼
SDA
1
0
0
1
A2
(1)
A1
(1)
(1)
A0
R/W
Start By
Master
0
0
0
0
0
0
P1
P0
ACK By
Device
ACK By
Device
Frame 1 Two-Wire Slave Address Byte
Stop By
Master
Frame 2 Pointer Register Byte
1
9
1
9
SCL
(Continued)
¼
SDA
(Continued)
1
0
0
1
A2
(1)
A1
(1)
(1)
A0
R/W
Start By
Master
D7
D6
D5
D4
D3
D2
ACK By
Device
D0
¼
ACK By
From
Device
Frame 3 Two-Wire Slave Address Byte
1
D1
Master
(2)
Frame 4 Data Byte 1 Read Register
9
SCL
(Continued)
SDA
(Continued)
D7
D6
D5
D4
D3
D2
D1
D0
From
Device
ACK By
Master
Stop By
Master
(3)
Frame 5 Data Byte 2 Read Register
(1)
The value of A0, A1, and A2 are determined by the connections of the corresponding pins.
(2)
Master should leave SDA high to terminate a single-byte read operation.
(3)
Master should leave SDA high to terminate a two-byte read operation.
Figure 10. Two-Wire Timing Diagram for Read Word Format
ALERT
1
9
1
9
SCL
SDA
0
0
0
1
Start By
Master
1
0
0
R/W
1
0
1
A2
(1)
ACK By
Device
Frame 1 SMBus ALERT Response Address Byte
(1)
0
A1
(1)
A0
From
Device
(1)
Status
NACK By
Master
Stop By
Master
Frame 2 Slave Address From Device
The value of A0, A1, and A2 are determined by the connections of the corresponding pins.
Figure 11. Timing Diagram for SMBus Alert
14
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
7.4 Device Functional Modes
7.4.1 Continuous-Conversion Mode
The default mode of the TMP75B is continuous conversion, where the ADC performs continuous temperature
conversions and stores each result to the temperature register, overwriting the result from the previous
conversion. Conversion rate bits CR1 and CR0 in the configuration register configure the TMP75B for typical
conversion rates of 37 Hz, 18 Hz, 9 Hz, or 4 Hz. The TMP75B has a typical conversion time of 27 ms. To
achieve different conversion rates, the TMP75B makes a conversion, and then powers down and waits for the
appropriate delay set by CR1 and CR0. The default rate is 37 Hz (no delay between conversions).Table 4 shows
the settings for CR1 and CR0.
Table 4. Conversion Rate Settings
CR1
CR0
CONVERSION RATE (TYP)
IQ (TYP)
0
0
37 Hz (continuous conversion, default)
45 μA
0
1
18 Hz
22 μA
1
0
9 Hz
12 μA
1
1
4 Hz
6.5 μA
After power-up or a general-call reset, the TMP75B immediately starts a conversion, as shown in Figure 12. The
first result is available after 27 ms (typical). The active quiescent current during conversion is 45 μA (typical at
+25°C). The quiescent current during delay is 1 μA (typical at +25°C).
Delay
(1)
Delay
(1)
27 ms
27 ms
27 ms
Startup
(1)
Start of
Conversion
Start of
Conversion
Delay is set by the CR bits in the configuration register.
Figure 12. Conversion Start
7.4.2 Shutdown Mode
Shutdown mode saves maximum power by shutting down all device circuitry other than the serial interface, and
reduces current consumption to typically less than 0.3 μA. Shutdown mode is enabled when the SD bit in the
configuration register is set to 1; the device shuts down after the current conversion is completed. When SD is
equal to 0, the device operates in continuous-conversion mode. When shutdown mode is enabled, the ALERT
pin and fault counter clear in both comparator and interrupt modes; however, this clearing occurs with the rising
edge of the shutdown signal. After shutdown is enabled, reprogramming shutdown does not clear the ALERT pin
and the fault counter until a rising edge is generated on the shutdown signal.
7.4.3 One-Shot Mode
The TMP75B features a one-shot temperature measurement mode. When the device is in shutdown mode,
writing a 1 to the OS bit starts a single temperature conversion. The device returns to the shutdown state at the
completion of the single conversion. This mode reduces power consumption in the TMP75B when continuous
temperature monitoring is not required. When the configuration register is read, the OS bit always reads zero.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
15
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
7.5 Programming
Figure 13 shows the internal register structure of the TMP75B. Use the 8-bit pointer register to address a given
data register. The pointer register uses the two LSBs to identify which of the data registers respond to a read or
write command. Figure 14 identifies the bits of the pointer register byte.
Pointer
Register
Temperature
Register
SCL
Configuration
Register
I/O
Control
Interface
TLOW
Register
SDA
THIGH
Register
Figure 13. Internal Register Structure
7.6 Register Map
Table 5 describes the registers available in the TMP75B with their pointer addresses, followed by the description
of the bits in each register.
Table 5. Register Map and Pointer Addresses
P1
P0
0
0
Temperature register (read only, default)
REGISTER
0
1
Configuration register (read/write)
1
0
TLOW register (read/write)
1
1
THIGH register (read/write)
Figure 14. Pointer Register (pointer = N/A) [reset = 00h]
7
6
5
4
3
Reserved
W-0h
2
1
P1
W-0h
0
P0
W-0h
LEGEND: R/W = Read/Write; R = Read only; W = Write only; -n = value after reset
16
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
Figure 15. Temperature Register (pointer = 0h) [reset = 0000h]
15
T11
14
T10
13
T9
12
T8
7
T3
6
T2
5
T1
4
T0
11
T7
10
T6
3
2
9
T5
8
T4
1
0
R-0h
Reserved
R-0h
R-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 6. Temperature Register Description
Name
Description
T11 to T4
The 8 MSBs of the temperature result (resolution of 1°C)
T3 to T0
The 4 LSBs of the temperature result (resolution of 0.0625°C)
Figure 16. Configuration Register (pointer = 1h) [reset = 00FFh]
15
OS
R/W-0h
14
7
6
13
12
CR
R/W-0h
11
10
POL
R/W-0h
9
TM
R/W-0h
8
SD
R/W-0h
3
2
1
0
FQ
R/W-0h
5
4
Reserved
R-FFh
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 7. Configuration Register Description
Name
OS
Description
One-shot mode
In shutdown (SD = 1), write 1 to start a conversion. OS always reads back 0.
CR
Conversion rate control
CR = 0h: 37-Hz conversion rate (typ) (default)
CR = 1h: 18-Hz conversion rate (typ)
CR = 2h: 9-Hz conversion rate (typ)
CR = 3h: 4-Hz conversion rate (typ)
FQ
Fault queue to trigger the ALERT pin
FQ = 0h: 1 fault (default)
FQ = 1h: 2 faults
FQ = 2h: 4 faults
FQ = 3h: 6 faults
POL
ALERT polarity control
POL = 0: ALERT is active low (default)
POL = 1: ALERT is active high
TM
ALERT thermostat mode control
TM = 0: ALERT is in comparator mode (default)
TM = 1: ALERT is in interrupt mode
SD
Shutdown control bit
SD = 0: Device is in continuous conversion mode (default)
SD = 1: Device is in shutdown mode
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
17
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
Figure 17. TLOW - Temperature Low Limit Register (pointer = 2h) [reset = 4B00h] (1)
15
L11
14
L10
13
L9
12
L8
11
L7
10
L6
3
2
9
L5
8
L4
1
0
R/W-4Bh
7
L3
6
L2
5
L1
4
L0
Reserved
R-0h
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
(1)
4B00h = 75°C.
Table 8. TLOW Register Description
Name
Description
L11 to L4
The 8 MSBs of the temperature low limit (resolution of 1°C)
L3 to L0
The 4 LSBs of the temperature low limit (resolution of 0.0625°C)
Figure 18. THIGH - Temperature High Limit Register (pointer = 3h) [reset = 5000h] (1)
15
H11
14
H10
13
H9
12
H8
11
H7
10
H6
3
2
9
H5
8
H4
1
0
R/W-50h
7
H3
6
H2
5
H1
4
H0
Reserved
R-0h
R/W-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
(1)
5000h = 80°C.
Table 9. THIGH Register Description
Name
Description
H11 to H4
The 8 MSBs of the temperature high limit (resolution of 1°C)
H3 to H0
The 4 LSBs of the temperature high limit (resolution of 0.0625°C)
18
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
8 Application and Implementation
8.1 Application Information
The TMP75B is used to measure the PCB temperature of the location it is mounted. The programmable address
options allow up to eight locations on the board to be monitored on a single serial bus. Connecting the ALERT
pins together and programming the temperature limit registers to desired values allows for a temperature
watchdog operation of all devices, interrupting the host controller only if the temperature exceeds the limits.
8.2 Typical Application
1.4 V to 3.6 V
0.01 PF
TMP75B
1
2
Two-Wire
Host Controller
3
4
SDA
VS
SCL
A0
ALERT
A1
GND
A2
8
7
6
Connect to VS or
GND for up to 8
Address
Combinations
5
1.4 V to 3.6 V
TMP75B
1
2
3
4
0.01 PF
SDA
VS
SCL
A0
ALERT
A1
GND
A2
8
7
6
Connect to VS or
GND for up to 8
Address
Combinations
5
Additional
Sensor
Locations
Figure 19. Temperature Monitoring of Multiple Locations on a PCB
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
19
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
Typical Application (continued)
8.2.1 Design Requirements
The TMP75B only requires pull-up resistors on SDA and ALERT, although a pull-up resistor is typically present
on the SCL as well. A 0.01-μF bypass capacitor on the supply is recommended, as shown in Figure 19. The
SCL, SDA, and ALERT lines can be pulled up to a supply that is equal to or higher than VS through the pull-up
resistors. To configure one of eight different addresses on the bus, connect A0, A1, and A2 to either VS or GND.
8.2.2 Detailed Design Procedure
The TMP75B should be placed in close proximity to the heat source to be monitored, with a proper layout for
good thermal coupling. This ensures that temperature changes are captured within the shortest possible time
interval.
8.2.3 Application Curves
Temperature (ƒC)
Figure 20 shows the step response of the TMP75B to a submersion in an oil bath of 100°C from room
temperature (27°C). The time-constant, or the time for the output to reach 63% of the input step, is 1.5 seconds.
100
95
90
85
80
75
70
65
60
55
50
45
40
35
30
25
±1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Time (s)
C007
Figure 20. Temperature Step Response
9 Power Supply Recommendations
The TMP75B operates with power supply in the range of 1.4 V to 3.6 V. It is optimized for operation at 1.8-V
supply but can measure temperature accurately in the full supply range.
A power-supply bypass capacitor is required for stability; place this capacitor as close as possible to the supply
and ground pins of the device. A typical value for this supply bypass capacitor is 0.01 μF. Applications with noisy
or high-impedance power supplies may require additional decoupling capacitors to reject power-supply noise.
20
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
TMP75B
www.ti.com
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
10 Layout
10.1 Layout Guidelines
Place the power-supply bypass capacitor as close as possible to the supply and ground pins. The recommended
value of this bypass capacitor is 0.01 μF. Additional decoupling capacitance can be added to compensate for
noisy or high-impedance power supplies.
Pull up the open-drain output pins (SDA and ALERT) to a supply voltage rail (VS or higher but up to 3.6 V)
through 10-kΩ pull-up resistors.
10.2 Layout Example
Via to Power or Ground Plane
Via to Internal Layer
Pull-Up Resistors
Supply Bypass
Capacitor
Supply Voltage
SDA
VS
SCL
A0
ALERT
A1
GND
A2
Ground Plane for
Thermal Coupling
to Heat Source
Serial Bus Traces
Heat Source
Figure 21. Layout Example
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
21
TMP75B
SBOS706B – APRIL 2014 – REVISED AUGUST 2014
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
SBOU141 — TMP75xEVM User's Guide
11.2 Trademarks
All trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
22
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TMP75B
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TMP75BID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-1-260C-UNLIM
-55 to 125
TMP75B
TMP75BIDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-55 to 125
T75B
TMP75BIDGKT
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-55 to 125
T75B
TMP75BIDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-1-260C-UNLIM
-55 to 125
TMP75B
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TMP75B :
• Automotive: TMP75B-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
31-May-2019
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TMP75BIDGKR
VSSOP
DGK
8
TMP75BIDGKT
VSSOP
DGK
TMP75BIDR
SOIC
D
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
8
250
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
31-May-2019
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TMP75BIDGKR
VSSOP
DGK
8
2500
366.0
364.0
50.0
TMP75BIDGKT
VSSOP
DGK
8
250
366.0
364.0
50.0
TMP75BIDR
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
A
.004 [0.1] C
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.150
[3.81]
.189-.197
[4.81-5.00]
NOTE 3
4X (0 -15 )
4
5
B
8X .012-.020
[0.31-0.51]
.010 [0.25]
C A B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 -8
.016-.050
[0.41-1.27]
DETAIL A
(.041)
[1.04]
TYPICAL
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
6X (.050 )
[1.27]
SYMM
5
4
(R.002 ) TYP
[0.05]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
METAL
SOLDER MASK
OPENING
EXPOSED
METAL
.0028 MAX
[0.07]
ALL AROUND
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
EXPOSED
METAL
.0028 MIN
[0.07]
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
6X (.050 )
[1.27]
SYMM
5
4
(R.002 ) TYP
[0.05]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising