Texas Instruments | TDC1000-C2000EVM | User Guides | Texas Instruments TDC1000-C2000EVM User guides

Texas Instruments TDC1000-C2000EVM User guides
TDC1000-C2000EVM User’s Guide
User's Guide
Literature Number: SNIU023
December 2014
Contents
6
7
8
9
............................................................................................................... 4
....................................................................................................................... 5
Equipment List .................................................................................................................... 6
Quick Start .......................................................................................................................... 6
Software Installation ............................................................................................................. 7
4.1
Graphical User Interface (GUI) ......................................................................................... 7
4.2
Installing the Driver ...................................................................................................... 7
4.3
Opening the GUI ......................................................................................................... 8
Hardware Configuration ........................................................................................................ 9
5.1
EVM Connections ........................................................................................................ 9
5.2
Jumpers ................................................................................................................... 9
5.3
LEDs...................................................................................................................... 10
GUI and operation .............................................................................................................. 10
Board Layout ..................................................................................................................... 14
Schematic ......................................................................................................................... 19
Bill of Materials .................................................................................................................. 22
2
Table of Contents
1
EVM Key Features
1.1
2
3
4
5
EVM
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
www.ti.com
List of Figures
1
TDC1000-C2000EVM Evaluation Board .................................................................................. 5
2
Water Container with 1-MHz Transducer ................................................................................. 6
3
Device Manager with COM Port Name ................................................................................... 7
4
TDC1000-C2000 GUI ....................................................................................................... 8
5
EVM J5 and J2 Connectors ................................................................................................ 9
6
EVM LEDs................................................................................................................... 10
7
EVM GRAPH................................................................................................................ 10
8
TOF of Water in Test Cell ................................................................................................. 11
9
EVM GUI - TDC1000 Tap ................................................................................................. 12
10
START, COMPIN and STOP Signals on Oscilloscope
11
12
13
14
15
16
17
18
...............................................................
Top Assembly Layer .......................................................................................................
Top Layer Routing .........................................................................................................
Power Layer Routing ......................................................................................................
Ground Layer Routing .....................................................................................................
Bottom Layer Routing (Flipped) ..........................................................................................
Schematic 1 .................................................................................................................
Schematic 2 .................................................................................................................
Schematic 3 .................................................................................................................
13
14
15
16
17
18
19
20
21
List of Tables
1
TDC1000-C2000EVM Bill of Materials
..................................................................................
SNIU023 – December 2014
Submit Documentation Feedback
List of Figures
Copyright © 2014, Texas Instruments Incorporated
22
3
User's Guide
SNIU023 – December 2014
General Description
This guide details the use of the TDC1000-C2000EVM evaluation module (referred to as EVM for the
remainder of this document). The TDC1000-C2000EVM is an evaluation module that allows users to
evaluate the operation and performance of the TDC1000-Q1 ultrasonic analog-front-end with C2000 RealTime Control microcontroller. The board can be used for many ultrasonic sensing applications such as
automotive fluid level detection, concentration and fluid identification, and proximity or distance
measurements. The EVM allows for two ultrasonic transducer connections, and two Resistance
Temperature Detectors (RTD) connections for temperature measurements. The EVM comes with a userfriendly Graphic User Interface (GUI) to modify the registers and display the data.
1
EVM Key Features
1.
2.
3.
4.
5.
6.
4
Evaluate TDC1000 Ultrasonic Analog-Front-End (AFE)
On-board C2000-TMS320F28035PAG Microcontroller
User Friendly TDC1000-C2000 GUI interface
Ports for two Ultrasonic Transducers
Ports for two RTD Sensors
Powered by USB
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
EVM Key Features
www.ti.com
1.1
EVM
Figure 1. TDC1000-C2000EVM Evaluation Board
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
5
Equipment List
2
www.ti.com
Equipment List
1.
2.
3.
4.
5.
TDC1000-C2000EVM or TIDA-00322EVM
TDC1000-C2000 GUI
Mini-USB cable
PC with Windows XP or Windows 7
Transducer (also known as an ultrasonic sensor)
(a) For water application, we recommend STEMiNC’s 1-Mhz transducer (p/n SMD10T2R111). The
sensor should be mounted in a water container. An acrylic container that we recommend can be
purchased from Tap Plastics. The example in this user guide uses a 30 mm × 30 mm × 50 mm
acrylic container with the STEMiNC’s transducer mounted on the side (see Figure 2).
Figure 2. Water Container with 1-MHz Transducer
(b) For air application, we recommend Murata’s 40kHz transducer (p/n MA40H1S-R) or ProWave’s 40
kHz transducer (p/n 400PT160).
3
Quick Start
1.
2.
3.
4.
5.
6.
7.
6
Download and Install TDC1000-C2000EVM (GUI) Software.
Fill a test cell with water. Make sure the water level is above the transducer.
Connect the test cell to TX1 and GND via J5 connector.
Connect the EVM board with a mini USB cable to the PC
Launch the GUI.
On the “GRAPH” tab, press the “START GRAPH” button.
The time of flight should be read in the TDC AVG VALUE section will show the TOF
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Software Installation
www.ti.com
4
Software Installation
This section describes software installation, firmware upgrade, and updating USB Driver.
4.1
Graphical User Interface (GUI)
Steps to install Windows GUI Installation file (version v1.0.2.59)
1. The latest Software for the EVM can be downloaded from the following locations:
(a) TDC1000-Q1 Tools and Software (http://www.ti.com/product/TDC1000-Q1/toolssoftware) or
(b) TIDA-00322 (http://www.ti.com/tool/TIDA-00322)
2. Notes on the software:
(a) The software must be installed before connecting the boards to the PC.
(b) The software is compatible with Windows XP and Windows 7.
3. Unzip the software folder
4. Run the “setup.exe” file
5. Follow the on-screen instructions to install the software. When the installation completes, click the
“Finish” button to exit.
4.2
Installing the Driver
1.
2.
3.
4.
To download the UART driver, go to http://www.ti.com/product/tusb3410/toolssoftware >>
Download the “TI WDF USBUART Single Driver" to your PC.
Connect the USB cable from the TDC1000-C2000EVM (J2) to a Windows7 PC/Laptop.
On your computer, right click on “My Computer” and select “System Properties”. Open the Device
Manager.
5. Scroll to Ports (COM & LPT) and expand this entry. Right click on “Ports (COM & LPT)”, then select
“Scan for hardware changes”
6. Select the UART driver that you downloaded (step 2)
7. Once completed, you should be able to see “TUSB3410 Device (COMx)” as seen below.
Figure 3. Device Manager with COM Port Name
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
7
Software Installation
4.3
www.ti.com
Opening the GUI
1. Run the TDC1000_C2000 GUI from the “Start Menu”. By default it is located in “Programs\Texas
Instruments\TDC1000_C2000”
2. GUI should automatically connect and show the following screen:
Figure 4. TDC1000-C2000 GUI
8
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Hardware Configuration
www.ti.com
5
Hardware Configuration
This section describes how to properly set up the connections on the EVM.
5.1
EVM Connections
1. If you haven’t done so, connect the USB cable to (J2) on the EVM and the other end of the cable to
the PC.
2. Attach one of the transducer wires to the terminals TX1 (J5.P10) and the other side to any of the
ground in (J5) connector (see Figure 5).
Figure 5. EVM J5 and J2 Connectors
5.2
Jumpers
For default operation, place jumpers on the following:
1. JP1.P1 - CLK-INT
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
9
Hardware Configuration
5.3
www.ti.com
LEDs
1. The V3p3 (D11) and VDUT (D10) LED are on if the board is powered.
2. If the 3p3V and DUT_VDD LED is off, check the physical connection to the PC.
3. The LINK LED is on if there is an established communication with the PC. If the LINK LED is blinking
when the EVM is connected to the PC without the GUI running, then the crystal oscillator has a fault.
NOTE: The LINK LED will blink while the GRAPH in the GUI is running.
Figure 6. EVM LEDs
6
GUI and operation
1. The EVM GUI software can be run by clicking on Start >> All Programs >> Texas Instruments >>
TDC1000_C2000.
Figure 7. EVM GRAPH
10
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
GUI and operation
www.ti.com
2. The message at the bottom of Figure 7 -- “Read All No Errors” -- means that the GUI is up and
running and all the registers and hardware connection are correct. Otherwise, refer to Section 4 and
make sure to follow all the steps.
3. Go to the “GRAPH” tab on the TDC1000-C2000EVM GUI and click “START GRAPH”.
(a) If you are using a 30 mm × 30 mm × 50 mm acrylic water container with STEMiNC’s 1 MHz
transducer mounted on the side (as discussed in Section 2), then you should be able to read the
TDC AVG VALUE ~40.8 µs as shown below.
Figure 8. TOF of Water in Test Cell
4. If the substance under test experiences any disturbance, either by impurities being added or by
shaking the container, the graph will represent this as a change on the TOF.
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
11
GUI and operation
www.ti.com
5. Follow the next steps to verify the TOF of the GUI on the oscilloscope.
(a) Enable constant trigger on the TDC1000 Tap on the GUI. The message "Start Continuous Trigger
Successful!!" should appear at the bottom of the GUI (see Figure 9).
(b) Connect the oscilloscope to the following connector:
(i) START (J4)
(ii) STOP (J3)
(iii) COMP_IN (J7).
Figure 9. EVM GUI - TDC1000 Tap
NOTE: Each of the registers of this tap are explained in the TDC1000 datasheet
12
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
GUI and operation
www.ti.com
Figure 10. START, COMPIN and STOP Signals on Oscilloscope
6. Observe the START (pink), STOP (blue) and COMP_IN (green) signals on the oscilloscope and
measure the time difference between the rising edge of the START signal to the rising edge of the
STOP signal. Verify the time difference between the rising edge of the START signal to the rising edge
of the STOP signal matches the “TDC AVG VALUE” on the GUI.
7. To verify TOF, use the following equation to find the width of the test cell. To corroborate the
calculated value measure the test cell with a metric Caliper.
t
d= v
2
where
•
•
•
d is the width of the test cell
t is the time of flight (TOF)
v is the speed of sound through the medium (water = 1484 m/s at 23°C.)
(1)
For example, the TOF of the test cell filled with water is 40.805 µs would be calculated as follows:
d=
40.805 ´ 10-3 s
´ 1484m / s = 30.28mm
2
(2)
The acrylic water container test cell is therefore 30.28 mm wide.
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
13
Board Layout
7
www.ti.com
Board Layout
NOTE:
The board layout is not to scale. The following figures are intended to show how the board
is laid out. It is not intended to be used for manufacturing.
Figure 11. Top Assembly Layer
14
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Board Layout
www.ti.com
Figure 12. Top Layer Routing
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
15
Board Layout
www.ti.com
Figure 13. Power Layer Routing
16
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Board Layout
www.ti.com
Figure 14. Ground Layer Routing
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
17
Board Layout
www.ti.com
Figure 15. Bottom Layer Routing (Flipped)
18
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Schematic
www.ti.com
8
Schematic
Figure 16. Schematic 1
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
19
Schematic
www.ti.com
Figure 17. Schematic 2
20
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Schematic
www.ti.com
Figure 18. Schematic 3
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
21
Bill of Materials
9
www.ti.com
Bill of Materials
Table 1. TDC1000-C2000EVM Bill of Materials
DESIGNATOR
QTY.
EVM
1
C1, C7, C9, C13, C18,
C21, C24, C26, C27,
C38, C46
11
C2, C6
VALUE
SV601136
0.1 uF
CAP, CERM, 0.1uF,
0603
16V, +/-5%, X7R, 0603
0603YC104JAT2A
10 pF
CAP, CERM, 10pF,
50V, +/-5%, C0G/NP0,
0603
0603
06035A100JAT2A
0.01 uF
CAP, CERM, 0.01uF,
50V, +/-10%, X7R,
0603
0603
C1608X7R1H103K
300 pF
CAP, CERM, 300pF,
50V, +/-5%, C0G/NP0,
0603
0603
GRM1885C1H301JA0
1D
2200 pF
CAP, CERM, 2200pF,
50V, +/-10%, X7R,
0603
0603
C0603X222K5RACTU
1 uF
CAP, CERM, 1uF,
10V, +/-10%, X7T,
0603
0603
GRM185D71A105KE3
6D
1000 pF
CAP, CERM, 1000 pF,
50 V, +/- 5%,
C0G/NP0, 0603
0603
C1608C0G1H102J
2.2 uF
CAP, CERM, 2.2uF,
10V, +/-10%, X6S,
0603
0603
GRM188C81A225KE3
4D
51 pF
CAP, CERM, 51pF,
100V, +/-5%,
C0G/NP0, 0603
0603
GRM1885C2A510JA0
1D
22 pF
CAP, CERM, 22pF,
50V, +/-5%, C0G/NP0,
0402
0402
GRM1555C1H220JA0
1D
33 pF
CAP, CERM, 33pF,
50V, +/-5%, C0G/NP0,
0402
0402
C0402C330J5GAC
1 uF
CAP, CERM, 1 µF, 10
V, +/- 10%, X7T, 0603
0603
GRM185D71A105KE3
6D
15 pF
CAP, CERM, 15pF,
50V, +/-5%, C0G/NP0,
0603
0603
06035A150JAT2A
10 uF
CAP, CERM, 10 µF,
10 V, +/- 10%, X7R,
0805
0805
GRM21BR71A106KE5
1L
6.8 pF
CAP, CERM, 6.8pF,
50V, +/-4%, C0G/NP0,
0603
0603
06035A6R8CAT2A
10 uF
CAP, CERM, 10uF,
10V, +/-10%, X7R,
0805
0805
GRM21BR71A106KE5
1L
0.1 uF
CAP, CERM, 0.1 µF,
16 V, +/- 5%, X7R,
0603
0603
0603YC104JAT2A
12
C4, C5
2
C10
1
C14, C22, C28, C29,
C35, C40, C44, C47,
C50, C55, C56, C57
12
C15
1
C16
1
C19, C20
2
C30, C32
2
C33, C34
2
C36, C41
2
C39, C42
2
C49, C52
2
C53
1
C54
1
C58
1
22
PART
NUMBER
TDC1000_C2000EVM
2
C3, C8, C12, C17,
C23, C25, C31, C37,
C43, C45, C48, C51
PACKAGE
REFERENCE
DESCRIPTION
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Bill of Materials
www.ti.com
Table 1. TDC1000-C2000EVM Bill of Materials (continued)
DESIGNATOR
QTY.
VALUE
D1, D2, D3, D4, D8,
D9
D10, D11, D12
1
3
TPD1E10B06DPYR
100 V
Diode, Ultrafast, 100V,
0.15A, SOD-123
SOD-123
1N4148W-7-F
Yellow
LED, Yellow, SMD
Yellow LED
SML-P12YTT86
FID1, FID2, FID3
H1, H2, H3, H4
N/A
3
Fiducial mark. There is Fiducial
nothing to buy or
mount.
4
Bumpon, Hemisphere,
0.44 X 0.20, Clear
Transparent Bumpon
SJ-5303 (CLEAR)
Header, TH, 100mil,
7x2, Gold plated, 230
mil above insulator
7x2 Header
TSW-107-07-G-D
1
MINI USB 2.0 SMT
9.2x9.9x4 mm
TYPE AB 5
CONTACTS R/A, SMD
651-305-142-821
1
1
Receptacle, 100mil,
7x2, Gold, R/A, TH
Receptacle, 7x2,
2.54mm, R/A, TH
SSW-107-02-G-D-RA
Connector,
Receptacle, 100mil,
5x2, Gold plated, R/A,
TH
5x2 R/A Header
Receptacle
PPPC052LJBN-RC
1
Header, TH, 100mil,
3x1, Gold plated, 230
mil above insulator
3x1 Header
TSW-103-07-G-S
1
Ferrite Bead, 60 ohm
@ 100MHz, 0.8A,
0603
0603
BK1608HS600-T
3
Thermal Transfer
Printable Labels,
0.650" W x 0.200" H 10,000 per roll
PCB Label 0.650"H x
0.200"W
THT-14-423-10
1
2.21k
RES, 2.21k ohm, 1%,
0.1W, 0603
0603
CRCW06032K21FKEA
51
RES, 51 ohm, 5%,
0.1W, 0603
0603
CRCW060351R0JNEA
200
RES, 200, 0.1%, 0.1
W, 0603
0603
RG1608P-201-B-T5
33.0
RES, 33.0 ohm, 1%,
0.1W, 0603
0603
CRCW060333R0FKEA
49.9
RES, 49.9 ohm, 1%,
0.1W, 0603
0603
CRCW060349R9FKEA
1.00k
RES, 1.00k ohm, 1%,
0.1W, 0603
0603
CRCW06031K00FKEA
10.0k
RES, 10.0k ohm, 1%,
0.1W, 0603
0603
RC0603FR-0710KL
0
RES, 0 ohm, 5%,
0.1W, 0603
0603
CRCW06030000Z0EA
56.0
RES, 56.0 ohm, 1%,
0.1W, 0603
0603
RC0603FR-0756RL
J1
J2
J5
J6
JP1
L1, L2, L3
60 ohm
LBL1
R1, R18, R77, R78
R2
R3, R4
R5, R6, R9, R16, R17,
R26, R29, R40, R42,
R43, R47, R85
R7, R11
R8, R14, R27
4
1
2
12
2
3
R10, R12, R13, R19,
R36, R38, R46
7
R21, R28, R32, R34,
R57, R58, R71, R80,
R81
9
R22
PART
NUMBER
ESD in 0402 Package DPY0002A
with 10 pF
Capacitance and 6 V
Breakdown, 1
Channel, -40 to +125
degC, 2-pin X2SON
(DPY), Green (RoHS &
no Sb/Br)
6
D5
PACKAGE
REFERENCE
DESCRIPTION
1
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
23
Bill of Materials
www.ti.com
Table 1. TDC1000-C2000EVM Bill of Materials (continued)
DESIGNATOR
R30
R33, R48, R52, R59,
R60, R61, R67, R73
R35, R75
R37, R54, R64, R65
R39, R49
R41
R50
R51
R53, R55, R79
R62, R63
R70
R72
R82, R83
R84
SH-JP1
SW1
QTY.
VALUE
RES, 5.36 k, 1%, 0.1
W, 0603
0603
CRCW06035K36FKEA
15.0k
RES, 15.0k ohm, 1%,
0.1W, 0603
0603
CRCW060315K0FKEA
100
RES, 100 ohm, 1%,
0.1W, 0603
0603
CRCW0603100RFKEA
1.50k
RES, 1.50k ohm, 1%,
0.1W, 0603
0603
CRCW06031K50FKEA
33.0k
RES, 33.0k ohm, 1%,
0.1W, 0603
0603
CRCW060333K0FKEA
1.00k
RES, 1.00 k, 0.01%,
0.063 W, 0603
0603
RNCF0603TKY1K00
90.9k
RES, 90.9k ohm, 1%,
0.1W, 0603
0603
RC0603FR-0790K9L
100k
RES, 100k ohm, 1%,
0.1W, 0603
0603
RC0603FR-07100KL
330
RES, 330 ohm, 5%,
0.1W, 0603
0603
CRCW0603330RJNEA
49.9
RES, 49.9, 1%, 0.1 W,
0603
0603
CRCW060349R9FKEA
51.1k
RES, 51.1k ohm, 1%,
0.1W, 0603
0603
CRCW060351K1FKEA
143k
RES, 143k ohm, 1%,
0.1W, 0603
0603
CRCW0603143KFKEA
10.0Meg
RES, 10.0 M, 1%, 0.1
W, 0603
0603
CRCW060310M0FKE
A
0
RES, 0, 5%, 0.1 W,
0603
0603
CRCW06030000Z0EA
1x2
Shunt, 100mil, Gold
plated, Black
Shunt
969102-0000-DA
Switch, Push Button,
SMD
2.9x2x3.9mm SMD
SKRKAEE010
Red
Test Point, Miniature,
Red, TH
Red Miniature
Testpoint
5000
Black
Test Point, Miniature,
Black, TH
Black Miniature
Testpoint
5001
TDC1000 Precision
AFE for Time of Flight,
PW0028A
PW0028A
TDC1000PW
1
Piccolo(TM)
Microcontrollers,
PAG0064A
PAG0064A
TMS320F28035PAG
1
8
2
4
2
1
1
1
3
2
1
1
2
1
1
1
13
TP8, TP9, TP10,
TP11, TP18
5
U1
U2
U3
TUSB3410
RS232 / IrDA Serial-to- RHB0032E
USB Converter, 2
MIPs, 16 KBytes,
8052, 3.3V, -40 to 85
degC, 32-Pin QFN
(RHB), Green (RoHS
& no Sb/Br)
TUSB3410IRHB
LMH6601MG
2.4V R-R Out CMOS
Video Op Amp with
Shutdown
MAA06A_L
LMH6601MG
2
1
Dual Buffer Gate,
DBV0006A
DBV0006A
SN74LVC2G34DBV
1
U4, U5
24
PART
NUMBER
5.36k
1
TP1, TP2, TP3, TP4,
TP5, TP6, TP15,
TP17, TP19, TP20,
TP21, TP22, TP23
U6
PACKAGE
REFERENCE
DESCRIPTION
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Bill of Materials
www.ti.com
Table 1. TDC1000-C2000EVM Bill of Materials (continued)
DESIGNATOR
QTY.
VALUE
U7
TPD8E003DQDR
TPD4S014DSQR
1
Complete USB Port
Protection Device, 4
Channels, -40 to +85
degC, 10-pin SON
(DSQ), Green (RoHS
& no Sb/Br)
1
128-Kbit Serial I2C
SOIC-8
Bus EEPROM, SOIC-8
M24128-BWMN6TP
MF05A
1
Micropower 150 mA
Low-Noise Ultra LowDropout Regulator, 5pin SOT-23, Pb-Free
LP2985AIM53.3/NOPB
MF05A
LP2980IM5X-ADJ
1
Micropower 50 mA
Ultra Low-Dropout
Adjustable Voltage
Regulator, 5-pin SOT23
SINGLE 2-INPUT
POSITIVE-OR GATE,
DCK0005A
DCK0005A
1
SN74AHC1G32TDCK
RQ1
OSC, 8 MHz, 1.8 3.3V, SMD
4-Pin SMD, Body 3.2 x ASEMB-8.000MHZ-LY2.5 mm , Height 0.9
T
mm
Crystal, 12Mhz, 18pF,
SMD
ABM3
ABM3-12.000MHZ-B2T
1
Crystal, 20 MHz, 10
pF, SMD
Crystal, 3.2x1.1x5.x
mm
ABM3B-20.000MHZ10-1-U-T
CAP, CERM, xxxF,
xxV, [TempCo], xx%,
[PackageReference]
Used in PnP output
Used in BOM report
0
Diode, Ultrafast, 100V,
0.15A, SOD-123
SOD-123
1N4148W-7-F
0
Connector, TH, BNC
Amphenol_112404
112404
6x1 Header
TSW-106-07-G-S
0
Header, TH, 100mil,
6x1, Gold plated, 230
mil above insulator
0
RES, 0 ohm, 5%,
0.1W, 0603
0603
CRCW06030000Z0EA
0
RES, 33 ohm, 5%,
0.1W, 0603
0603
CRCW060333R0JNEA
RES, xxx ohm, x%,
xW,
[PackageReference]
Used in PnP output
Used in BOM report
U8
TPD4S014
U10
U11
U12
Y1
1
Y2
Y3
1
815-ABM3-12-B2-T
C11
D6, D7
J3, J4, J7, J8, J9
0
100V
J10
R15, R56
R20
0
0
R23
0
R24, R25
0
4.7k
CRCW06034K70JNEA
RES, xxx ohm, x%,
xW,
[PackageReference]
Used in PnP output
Used in BOM report
3.0k
RES, 3.0k ohm, 5%,
0.1W, 0603
0603
CRCW06033K00JNEA
33.0
RES, 33.0 ohm, 1%,
0.1W, 0603
0603
CRCW060333R0FKEA
0
R45
0
0
DSQ0010A
RES, 4.7 k, 5%, 0.1 W, 0603
0603
R31
R44
PART
NUMBER
ESD Array For
DQD0008A
Portable Space-Saving
Applications, 8
Channels, -40 to +85
degC, 8-pin WSON
(DQD), Green (RoHS
& no Sb/Br)
1
U9
PACKAGE
REFERENCE
DESCRIPTION
SNIU023 – December 2014
Submit Documentation Feedback
General Description
Copyright © 2014, Texas Instruments Incorporated
25
Bill of Materials
www.ti.com
Table 1. TDC1000-C2000EVM Bill of Materials (continued)
DESIGNATOR
R66, R68
R69
R74
R76
TP7, TP12, TP13,
TP14, TP16
26
QTY.
0
0
0
0
0
VALUE
PACKAGE
REFERENCE
DESCRIPTION
PART
NUMBER
0
RES, 0, 5%, 0.1 W,
0603
0603
MCR03EZPJ000
1.00k
RES, 1.00k ohm, 1%,
0.1W, 0603
0603
CRCW06031K00FKEA
0
RES, 0 ohm, 5%,
0.1W, 0603
0603
ERJ-3GEY0R00V
100k
TRIMMER, 100K,
0.25W, SMD
4.8x3.71x4.6mm
3224J-1-104E
Red
Test Point, Miniature,
Red, TH
Red Miniature
Testpoint
5000
General Description
SNIU023 – December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan are NOT certified by
TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, User is required by Radio Law of Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising