Vision | Quick Release QR-91 114L/146L | Installation instructions | Vision Quick Release QR-65 112L/143L Installation Instructions

Vision Quick Release QR-65 112L/143L Installation Instructions
QR Installation Instructions
Published – May, 2010.
ZS104.v0 © Full Speed Ahead
WASHER
QR LEVER
OK
CAM
OK
Fig.3
Fig.2
OK
NO!
Fig.4
QR Lever Fully Closed- Lever full closed after moderate force.
retention safety tabs
QR Lever 3/4 Closed- Lever tension should have increased
enough to require moderate force to close, but not so much
that closing lever is difficult or painful to hand.
Fig.1
QR Lever 1/2 Closed- Lever should be under light tension.
QR Nut- tighten until contacst the
frame when lever is fully open
Fig.5
QR Lever Fully Open- Should be zero tension on the lever
Introduction
Congratulations on your Full Speed Ahead product. Please read these instructions and follow them for correct use. Failure to follow the warnings and instructions could result in damage to product which is not covered
under warranty, damage to bicycle; or cause an accident resulting in injury or death. Since specific tools and experience are necessary for proper installation, it is recommended that the product be installed by a
qualified bicycle technician.
Warranty
Full Speed Ahead (FSA) warrants all FSA, Gravity, Vision and RPM products to be free from defects in materials or workmanship for a period of two years after original purchase unless otherwise stated in the full
warranty policy. The warranty is non-transferable and valid to the original purchaser of the product only. Full warranty policy is available at http://www.fullspeedahead.com/techdoc
Regularly check the wheels to be certain they are fastened securely to the bicycle fork. If the Quick Release is not installed correctly, the wheel may become separated
from the fork and result in an accident, personal injury or death.
It is the user’s responsibility to examine the product on a regular basis to determine the need for service or replacement. Cyclists should inspect their bicycle and parts on a regular basis in order to detect damage
that may have occurred from normal use or for missing parts. Check all parts for damage and wear before every use. Should any problems or concerns arise discontinue riding the bicycle and have it inspected by a
qualified bicycle technician. Do not ride the bicycle until all problems are corrected, repaired, or replaced.
FSA Quick Release Specification
PRODUCT
FSA MERCURY CARBON
VISION MERCURY CARBON
FSA MERCURY ALLOY
VISION MERCURY ALLOY
FSA SCATTO Road
QR-88
QR-89
QR-66
QR-89
QR-61
ITEM CODE
750-0035
750-0036
750-0039
750-0037
750-0005
WHEEL COMPATIBILITY
Road Only Standard Front / 130mm Hub Spacing Rear
FSA SCATTO ATB
FSA QR-60 Road
QR-61 Black Finish
750-0010
MTB Standard Front / 135mm Hub Spacing Rear
QR-60 Black Finish
750-0025
Road Standard Front / 130mm Hub Spacing Rear
FSA QR-60 ATB
QR-60 Black Finish
750-0030
MTB Standard Front / 135mm Hub Spacing Rear
FSA QR-22
QR-22 Black Finish
Carbon Finish FSA Logo
Carbon Finish Vision Logo
Black Finish FSA Logo
Black Finish Vision Logo
Black Finish
Road Only Standard Front / 130mm Hub Spacing Rear
Road Standard Front / 130mm Hub Spacing Rear
Road Standard Front / 130mm Hub Spacing Rear
Wheel Installation
 This Quick Release device is designed and intended for use only on bicycle wheels.
 FSA Quick Release devices are intended to be used only with forks that have retention safety tabs on the dropouts to prevent accidental wheel detachment from the fork (Fig.1).
 If you are unfamiliar with Quick Release assembly it is recommended to ask for advice from your local bike shop. Riding with an improperly assembled Quick Release can cause the wheel to shift while in use
resulting in accident and injury.
 Regularly check the QR adjustment. If the Quick Release is not installed correctly, the wheel may become separated from the fork and result in an accident, personal injury or death.
 When the QR is on the closed position make sure that the lever cam is correctly seated in the cam guide washer (Fig.2 Fig.3).
 Always close the skewer lever completely. Do not allow a frame or fork tube or any other member to inhibit full lever travel when closing. Failure to close the lever completely will limit cam engagement and
the skewer's ability to hold the wheel in place. (Fig.4)
 The QR must be periodically lubricated at the pivot points so it can exert maximum sideways force.
1. Insert Quick Releases into wheels. The lever of the Quick Releases should go on the non-drive side. Thread the Quick Release nut, but do not tighten. Note: Front Quick Release is shorter than Rear.
2. Install the Front and Rear Wheels into the drop-outs of the fork and frame. With the QR lever in the open position, tighten the QR nut until it is in contact with the frame or fork dropouts. Close the QR lever.
The QR lever should require substantial effort to close the last 25-30 degrees. If it closes with only moderate hand pressure, the QR must be readjusted by opening the QR lever, then turning the QR nut
clockwise until the closing action of the QR lever requires the recommended force. See (Fig.5) for details.
Scatto Model quick release levers have a higher leverage ratio than other models. Scatto levers require less effort to close properly than tradition quick release levers. Using too much leverage can cause damage to
the lever making it difficult to remove, or cause the wheel to shift while riding causing loss of control of the bicycle. Always seek advice from a qualified bicycle technician in regards to proper quick release lever use
and installation.
Quick Release Maintenance
Check periodically all QR parts, clean and lubricate lever’s cam mechanism, pivot points and spindle to prevent corrosion. If the QR shows signs of wear, it must be replaced before riding.
Replacement parts are available for purchase through all bicycle service and retail locations. If the bicycle shop does not stock the necessary parts, they can be ordered by the retail location from a VISION distributor
or VISION directly. A list of distributors is available at www.fullspeedahead.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising