Vision | TEAM CLIP-ON S-BEND | Installation instructions | Vision TEAM CLIP-ON J-BEND Installation Instructions

Vision TEAM CLIP-ON J-BEND Installation Instructions
Vision Team Clip-On Handlebar Installation Instructions
Published – Dec, 2016.
ZS192.v0 © Full Speed Ahead
Introduction
Congratulations on your Vision product. Please read these instructions and follow them for correct use. Failure to follow
the warnings and instructions could result in damage to product not covered under warranty, damage to bicycle; or
cause an accident resulting in injury or death. Since specific tools and experience are necessary for proper installation, it
is recommended that the product be installed by a qualified bicycle technician. FSA & Vision assumes no responsibility
for damages or injury related to improperly installed components.
Warranty
Full Speed Ahead (FSA) warrants all FSA, Vision, Metropolis and RPM products to be free from defects in materials or
workmanship for a period of two years after original purchase unless otherwise stated in the full warranty policy. The
warranty is non-transferable and valid to the original purchaser of the product only. Any attempt to modify the product in
any way such as drilling, grinding, and painting will void the warranty. For more information on warranty policy and
instructions for completing a warranty claim, check out the Full Warranty Policy found at our website:
http://www.visiontechusa.com/support/warranty-policy/
Always use a calibrated torque wrench to tighten all screws and bolts when assembling and adjusting the
vision handlebar to the bicycle. Failure to use a calibrated torque wrench can cause damage to the handlebar making it
unsafe to ride, and is not covered under warranty. Check bolt and screw torque before each ride to ensure they have not
loosened during use.
Periodically inspect your aerboars for any cracks, chips, scratches, and any other visible damage. In the
event of an accident do not ride the bicycle until the handlebars have been inspected by an experienced mechanic as the
aerobars may be damaged or weakened even if no visible damage is apparent. If there is any visible damage, the
aerobars should not be used any further and replaced.
Specification
These instructions are for the installation and adjustment of the following Vision Brand components only:
Item Number / Model Name HB-RO-a410/SB / Team Clip-on Bar-Close (1-Piece)
HB-RO-a420/JB / Team Clip-on Bar-Open (2-Piece)
Components
Follow the assembly order in the illustration:
① Handlebar
② Clamp Bolts (16 mm)x4
③ Lower Clamp x2
④ Upper Clamp x2
⑤ Armrest Mount (L & R) x2
⑥ Aero Extension (L & R) x2
⑦ Aero Extension Bolts (35 mm) x2
⑧
⑨
⑩
⑪
⑫
⑬
⑭
Armrest Plates (L & R) x2
Washer x4
Armrest Plates Fixing Bolts (10mm) x4
Adhesive Velcro Strips x2
Armrest Pad x2
Aero Extension Front Plug x2
Aero Extension Rear Plug x2
Clip-On Aerobar installation
1. Vision clip-on bar clamps are Φ31.8mm diameter. Ensure handlebar is compatible with clip-on aero bars and is Φ31.8mm diameter. FSA reccommends using carbon installation compound between clamp surfaces and handlebar,
especially on clip-on compatible carbon handlebars. DO NOT apply grease to any of the clamping surfaces.
Installing clip-on aerobars on a non-compatible handlebar can cause damage to the handlebar and may result in accident, injury or death.
2. Install Upper and Lower Clamps ③, ④ on the handlebar ①. Move the clamp plates to the desired width. Alternately tighten Clamp Bolts ② to 60 kgf.cm / 6 Nm / 53 in.lbs.
To ensure clamping security and safety, install clip-on bars only on the round center section of handlebar. Do not install clip-on bar on any tapered or shaped section of handlebar.
Installing clip-on bar in any location other than the round center section may cause slippage or damage to handlebar or aerobar resulting in loss of control, accident, injury or death.
3. Install Aero Extensions ⑥ in to Upper Clamp ④ and Armrest Mount ⑤. Set to desired length. Alternately tighten Aero Extension Bolts ⑦ to 60 kgf.cm / 6 Nm / 53 in.lbs.
4. Choose the desired armrest position and attach the Armrest Plate ⑧ to Armrest mount ⑤. Install Armrest Plate Fixing Bolts ⑩ and Washers ⑨ and tighten to 60 kgf.cm / 6 Nm / 53 in.lbs.
Always use a calibrated torque wrench to tighten armrest fixing bolts.
Always install the armrest bolts with washers. Installing armrest bolts without washers can cause armrests to crack and fail unexpectedly while riding resulting in loss of control of bicycle.
5. Remove the adhesive velcro strips ⑪ from armrest pads ⑫ and attach to the top surface of left and right armrest plates.
6. Press Aero Extension Front and Rear Plugs ⑬, ⑭ in to aero extension.
Use only supplied Vision bolts for installation. Using bolts other than original supplied bolts may cause damage to extension bar threads resulting in armrest plate position deflection while riding, resulting in loss of
control of bicycle and can cause serious accident or injury. Apply threadlocker to the fixing bolts threads.
Team Clip on aerobars must not be trimmed or cut from the front or rear. Cutting aerobars will void the warranty.
Team Clip-on aerobars are not compatible with bar-end shifters. Using bar-end shifters with Team Clip-on aerobars will void the warranty.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising