EdgeStar | VBR440 | Owner Manual | EdgeStar VBR440 Built-In Commercial Beverage Merchandiser Owner Manual

EdgeStar VBR440 Built-In Commercial Beverage Merchandiser Owner Manual
Beverage Cooler
VBR440
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the EdgeStar beverage cooler and/or injury to the user. This beverage
cooler is designed for domestic indoor use only. Any other use may invalidate the warranty. Please review the rating
label located on the lower left side of the inner cabinet of the unit for electrical and other technical data related to this
unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire, electric shock or injury.
Electrical Safety
 Do not exceed the power outlet ratings.
 It is recommended the beverage cooler be
connected on its own circuit.
 The unit must be installed in accordance with
state and local electrical codes.
 A standard electrical supply (115 V, 60Hz), that is
properly grounded in accordance with the
National Electrical Code and local codes and
ordinances is required.
 Use outlets that cannot be turned off by a switch
or pull chain.
 Always turn the unit off and unplug it from the
outlet when cleaning.
 Unplug the unit if it is not going to be used for an
extended period of time.
 Do not operate the unit with a power plug missing
the ground plug, a damaged cord or a loose
socket.
 Be sure the beverage cooler is properly
grounded.
 Never plug or unplug the unit with wet hands.
 Do not bypass, cut or remove the grounding plug.
 Do not use extension cords or power strips with
this unit. You may need to contact your electrician
if it is necessary to use a longer cord or if you do
not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other
appliances.
 Do not start or stop the unit by switching the
circuit’s power on and off.
 If the power cord is damaged, it must be replaced
by the manufacturer or a qualified technician.
 Never repair the unit while it is plugged in.
 Immediately unplug the unit if it makes strange
sounds, emits smells or smoke comes out of it,
and contact customer service.
 Do not remove any part of the casing unless
instructed by an authorized technician.
 You should never attempt to repair the unit
yourself.
 Contact customer service for service options if the
unit needs service.
i
General Safety
 To prevent back and other types of injuries, use at
least two people to move and install the beverage
cooler.
 This appliance is not intended for use by persons,
including children, with reduced physical, sensory or
mental capabilities, unless they have been given
supervision or instruction concerning the use of the
appliance by the person(s) responsible for their
safety.
 Install the beverage cooler in a well-ventilated area
where the ambient temperature is above 60°F and
below 90°F.
 The temperature range for this cooler is optimized
for beverage storage. Perishable food items may
require a different storage environment.
 Do not place hot or warm items into the cooler
before they cool down to room temperature.
 This unit is designed to be installed indoors, and
protected from rain, sleet, snow, and/or moisture.
 This unit is not intended to be used by children.
 Children should be supervised to ensure that they
do not play with this product.
 Never allow children to crawl inside the beverage
cooler. If disposing the unit, remove the door.
 Do not use this appliance near flammable gas or
combustibles, such as gasoline, benzene, thinner,
etc.
 Do not place the unit near heat sources such as
ovens, grills, or direct sunlight.
 Only use in an upright position on a flat, level
surface and provide proper ventilation.
 Do not pinch or kink the power supply line between
the unit and cabinet.
 Do not leave any cleaning solutions in the unit
 Do not use solvent-based cleaning agents or
abrasive solutions to clean the unit as they may
damage the interior and exterior.
 Do not place any other appliances on top of the unit.
 Do not turn the unit upside down, on its side, or at
an angle off level.
 If your model beverage cooler is equipped with a
lock, take care to keep the keys away from children.
 Do not move the unit without emptying the contents
and securing the door in a closed position.
Important Safety Information (Continued)
R600a
This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a), which is
environmentally friendly, but flammable. It does not damage the ozone layer, nor does it contribute to
greenhouse gases. Care must be taken during transportation and set up of the appliance. Make sure
to check that no parts of the cooling system are damaged. Leaking coolant can ignite and may cause
personal injury.
In the event of any damage:







Avoid open flames and anything that may create a spark.
Disconnect from the main power supply.
Vent the room in which the appliance is located for several minutes.
Contact the EdgeStar Customer Service Department for advice.
The more coolant there is in an appliance, the larger the room it should be installed in. In the
event of a leak, if the appliance is in a small room, there is the danger of combustible gases
building up. For every ounce of coolant at least 325 cubic feet of room space is required. The
amount of coolant in the appliance is stated on the rating label in the lower left side of the
inner cabinet of the appliance. It is hazardous for anyone other than an Authorized Service
Person to carry out servicing or repairs to this appliance.
Take serious care when handling, moving and using the appliance to avoid either damaging
the refrigerant tubing, or increasing the risk of a leak.
Replacing component parts and servicing must be done by manufacturer authorized service
personnel, so as to minimize the risk of possible ignition due to incorrect parts or improper
service.
Risk of child entrapment!
Before discarding your old appliance:


Take off the door(s).
Leave the shelves in place so that children cannot easily crawl into the unit.
- SAVE THESE INSTRUCTIONS -
EdgeStar Beverage Cooler
ii
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I
IMPORTANT SAFETY INFORMATION (CONTINUED) ....................................... II
INTRODUCTION ................................................................................................... 1
PARTS IDENTIFICATION ..................................................................................... 2
FRONT VIEW ........................................................................................................ 2
INSTALLING THE BEVERAGE COOLER ........................................................... 3
TYPES OF INSTALLATION....................................................................................... 3
Freestanding installation: .............................................................................. 3
Built-in installation: ........................................................................................ 3
ELECTRICAL REQUIREMENTS ................................................................................ 5
Recommended grounding method ................................................................ 5
LEVELING THE BEVERAGE COOLER ....................................................................... 5
INSTALLING AND REMOVING THE SHELVES ............................................................ 6
INSTALLING THE HANDLE ...................................................................................... 7
OPERATION .......................................................................................................... 8
INSTALLATION CHECKLIST BEFORE OPERATION ..................................................... 8
USING THE TEMPERATURE CONTROL PANEL ......................................................... 8
NORMAL SOUNDS .............................................................................................. 10
DEFROSTING ..................................................................................................... 10
PREPARING THE BEVERAGE COOLER FOR STORAGE............................................ 10
CLEANING AND MAINTENANCE ...................................................................... 11
EXTERIOR CLEANING ......................................................................................... 11
INTERIOR CLEANING ........................................................................................... 11
TROUBLESHOOTING ........................................................................................ 11
TROUBLESHOOTING CONTINUED ......................................................................... 12
TROUBLESHOOTING CONTINUED ......................................................................... 13
SPECIFICATIONS ............................................................................................... 14
First Time Operating Instructions
Before use, make sure all packaging labels and materials are all removed from
the unit. Be sure to keep track of all included parts and pieces before discarding
packaging materials. It is advised that you keep the original box and packaging
materials in case you are ever to move or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling
components time to settle from transit. The instruction manual should be read
before use.
This owner’s manual is provided for reference use only. Specifications may
change without prior notice. Refer to the product label on the back of your
beverage cooler for the latest technical information.
iii
Introduction
Thank you for purchasing this EdgeStar beverage cooler. We are glad you chose
us. We believe that your purchase of this product opens a relationship between
you and EdgeStar. We will provide the customer support needed to nurture that
relationship.
This manual contains important information regarding the proper installation, use
and maintenance of your beverage cooler. Following this manual will ensure that
your product will work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport
your beverage cooler.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located on the
rating label on the lower left side of the inner cabinet of your
unit and are needed to obtain warranty service. You may also
want to staple your receipt to this manual as it is the proof of
your purchase, and is also needed for service under your
warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
1

If you received a damaged product, immediately contact the retailer or
dealer that sold you the product.

Read and follow this instruction manual carefully to help you install, use
and maintain your beverage cooler.

Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.

Visit us on the web at http://www.edgestar.com to register your
product, download product guides, additional troubleshooting resources
and up-to-date information.

If you need warranty service, our friendly customer service
representatives are available via email at service@edgestar.com or by
telephone at 1 (866) 319-5473.
Parts Identification
Front View
Tip: Gather the model
and serial number
from the product label
and write them down
before installing the
beverage cooler.
EdgeStar Beverage Cooler
2
Installing the Beverage Cooler
The beverage cooler should be installed in accordance with local
electrical code requirements. The beverage cooler should also be placed
in a location that is strong enough to support its total weight, keeping in
mind that it will weigh substantially more when fully loaded than when
empty.
Before you plug the beverage cooler into a power supply, be sure to let it
stand upright for at least 24 hours to allow the compressor’s oils to settle.
Unpacking the Beverage Cooler
WARNING: Use two or more people to move and install the beverage
cooler. Failure to do so can result in back or other injury. Carefully remove
the packaging materials. Remove any shipping tape and glue from your
beverage cooler before using. Do not use sharp instruments, rubbing
alcohol, flammable fluids, or abrasive cleaners to remove tape or glue.
These products can damage the surface of your beverage cooler.
IMPORTANT: Do not remove any safety, warning, or product information
labels from your beverage cooler.
Types of Installation
Important Notes:
• Choose a location that has
ambient temperatures above
60°F and below 90°F.
Operation outside these
temperatures may result in
lowered efficiency or cause
other adverse effects.
• This unit MUST be installed
in an area protected from the
elements, e.g., wind, rain,
water spray or drips.
• The beverage cooler should
not be located next to ovens,
grills or other high heat
sources.
• Do not kink or pinch the
power supply cord between
the beverage cooler and wall.
This beverage cooler has been designed for freestanding or built-in
installation. Regardless of installation type, there must be adequate
ventilation and access for service.
Freestanding installation:
A freestanding installation will allow you to install the beverage cooler in
almost any place you desire. However, the unit does need an open
environment in order to vent properly. You must follow the stated
instructions for electrical requirements, and leveling the beverage cooler.
Built-in installation:
A recessed installation will allow you to install the beverage cooler under
a counter or in a kitchen cabinet provided the required clearance space
around the beverage cooler is followed.
It is necessary to allow adequate ventilation space around the unit (make
sure there is at least some ventilation room for the back of the unit). The
following additional items must be observed.
1. Place the beverage cooler in front of the installation location. Adjust
the feet and place the unit flat on the floor or on a platform depending
on your installation requirements.
2. If the electrical outlet for the beverage cooler is behind the cabinet,
plug in the beverage cooler.
3. Push the beverage cooler into position.
WARNING: Do NOT install the beverage cooler behind a closed cabinet
door.
3
Installation Clearance Requirements
When installing the beverage cooler under a counter, follow the
recommended spacing dimensions shown.
• To ensure proper service access and ventilation, allow at least 2/5”
clearance at the back, 1/5” at top and 1/5” at sides. The installation
should allow the unit to be pulled forward for servicing, if necessary.
Top View
Back of unit
Door Hinge
Side View
• The beverage cooler should be installed on a firm and level surface that
will be able to support the entire weight of a fully loaded unit. It is
important for the beverage cooler to be level in order to work properly. If
needed, you can adjust the height of the beverage cooler by rotating the
feet. See the “Leveling the Beverage Cooler” section.
• A standard electrical supply (115 VAC only, 60 Hz), properly grounded
in accordance with National Electrical Code and local codes and
ordinances is required.
EdgeStar Beverage Cooler
4
Electrical Requirements





ELECTRIC SHOCK HAZARD!
Plug into a grounded 3-prong outlet.
Never remove the grounding prong from the plug.
Never use an adapter to bypass the grounding prong.
DO NOT use an extension cord.
Failure to follow these instructions can result in fire,
electrical shock, or death.
Before you move your beverage cooler into its final location, it is
important to make sure you have the proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in
accordance with the National Electrical Code and local codes and
ordinances, is required.
It is recommended that a separate circuit, serving only your beverage
cooler, be provided. Use receptacles that cannot be turned off by a switch
or pull chain.
The fuse (or circuit breaker) size should be 15 Amps.
Recommended grounding method
For your personal safety, this appliance must be grounded. It is equipped
with a power supply cord having a 3-prong grounding plug. To minimize
possible shock hazard, the cord must be plugged into a mating 3-pronged
wall socket, and grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall socket is not
available, it is the personal responsibility of the customer to have a
properly grounded, 3-prong wall receptacle installed by a qualified
electrician.
Leveling the Beverage Cooler
It is important for the beverage cooler to be leveled in order to work
properly. It can be raised or lowered by rotating the plastic sheaths
around each of the feet on the bottom of the machine. If you find that the
surface is not level, rotate the feet until the beverage cooler becomes
level .You may need to make several adjustments to level it. We
recommend using a carpenter’s level to check the machine.
1. Place a carpenter’s level on top of the product to see if the beverage
cooler is level from front to back and side to side.
2. Adjust the height of the feet as follows:
Turn the leveling feet to the right to lower that side of the cooler.
Turn the leveling feet to the left to raise that side of the cooler.
IMPORTANT: Once you are ready to install it in a cabinet or directly on
the floor, you must adjust the feet to level the beverage cooler.
5
Installing and Removing the Shelves
To prevent damaging the door gasket, make sure to open the door all the
way before pulling the shelves out of their track.
To install the shelves:
1. Open the door completely.
2. Slide the shelf on the shelf track and slowly push back until it stops.
3. Push down on the front of the shelf to allow the back of the shelf to lift
over the plastic post. (Imagine a seesaw movement.) Continue to push
the shelf back until both notches pass through the plastic posts on each
side of the shelf track.
4. Continue to push the shelf back.
To remove the shelves:
1. Open the door completely.
2. If necessary, make sure you remove all the contents sitting on the
shelf.
3. Pull the shelf forward until the notch aligns with the plastic post on each
side of the shelf track.
4. Lift the shelf until both notches pass through the posts.
5. Continue to pull the shelf forward until it is completely removed from
the inner compartment.
EdgeStar Beverage Cooler
6
Installing the Handle
IMPORTANT: Do not over tighten the screws and do not use power tools
to install the handle.
Place the handle over the fixing pin(s) of the door. Using the supplied Allen
wrench, tighten the grub screw(s) to secure the handle.
7
OPERATION
Installation Checklist Before Operation
1. Have all packing materials and tape been removed from the interior and
exterior of the beverage cooler?
2. Have the installation instructions been followed, including connecting the
machine to electricity? And has proper grounding been installed for the beverage
cooler?
3. Has the machine been leveled?
4. Is the beverage cooler in a site where the ambient temperature is between
60ºF and 90ºF all year round?
Using the Temperature Control Panel
Basic Functions
To turn the beverage cooler on/off, press and hold the
button for five (5) seconds.
Note: Whether your
beverage cooler can reach
the actual set temperature
depends on the ambient
environmental conditions.
(power)
Use the up and down buttons to adjust the temperature. The temperature
displayed can be in Fahrenheit or Celsius. This beverage cooler has a
temperature range from 36°F to 43°F or 2°C to 6°C. To toggle between
Fahrenheit and Celsius display, press and hold the
(5) seconds.
button for five
Press the
button on the control panel to lower the temperature
by one (1) degree increments.
Press the
button on the control panel to raise the temperature
by one (1) degree increments.
Caution: If you powered off
the unit, please wait at least
5 minutes before powering it
back on.
Press the
button to toggle between interior lighting modes. By
default, the unit will be in functional mode. In this mode, the interior light
will only turn on when the door is open. This unit is also equipped with a
showcase mode. In showcase mode, the interior light always stays on.
This beverage cooler has two displays, a Set Display that shows the set
temperature, and a Current Temperature Display that shows the current
temperature. Note: It is normal to see the set temperature and current
temperature displays being a few degrees off from each other. If,
however, the current temperature deviates more than 9°F from the set
temperature, the display will continue to flash.
EdgeStar Beverage Cooler
8
Allow at least 24 hours
before storing your
beverages to allow the
temperature to acclimate.
Advanced Functions
This unit is equipped with a temperature alarm. The alarm will sound and
the temperature display will flash under the following conditions:
- The door has been left open for more than 60 seconds.
- There has been a lengthy interruption to the power supply.
- The ventilation opening is covered or there is a large build-up of
debris.
Simply pressing the power button once will disable the alarm.
Sabbath Mode
This unit is equipped with Sabbath mode for the observance of religious
holidays. This mode turns off the display, interior light and the alarm.
To enable Sabbath mode, press and hold the
and
buttons for five (5) seconds. A small red light in the lower right corner of
the display will flash four (4) times, confirming that the unit is now in
Sabbath mode. The unit will exit Sabbath mode automatically after 96
hours or the user can once again press and hold the
buttons for five (5) seconds.
and
Silent Mode
By default, this beverage cooler uses powerful fan forced air circulation
for even cooling. While these fans are extremely quiet, you can turn them
off by entering the unit into silent mode. Press and hold the
for
approximately five (5) seconds. The unit will beep three (3) times to
confirm it is in silent mode. To change back to normal fan operation,
press and hold the
key for five (5) seconds. The unit will beep
five (5) times to confirm it has resumed normal operation.
9
Normal Sounds
Your new beverage cooler may make sounds that are not familiar to
you. Most of the new sounds are normal. Hard surfaces like the
floor and walls can make the sounds seem louder than they
actually are. The following describes the kinds of sounds that might
be new to you and what may be making them.
 Rattling noises may come from the flow of the refrigerant. Items
stored on top of the beverage cooler can also make noises.
 The high efficiency compressor may make a pulsating or highpitched sound.
 As each cycle ends, you may hear a gurgling sound due to the
refrigerant flowing in your beverage cooler.
 You may hear air being forced over the condenser by the
condenser fan.
Defrosting
Note that under most refrigerating settings, the unit will
automatically defrost under most ambient conditions. However, on
colder settings, some frost may build up. Additionally, the more
humid the ambient conditions, the more frost may build up. Keep
the door closed as much as possible and avoid opening the door
unnecessarily to minimize frost build-up.
If frost is preventing the door from closing properly, you may need
to power the unit off until the frost melts. Use a soft absorbent towel
to dry the unit.
WARNING: Never attempt to remove frost with a sharp object!
Preparing the Beverage Cooler for Storage
If the beverage cooler will not be used for a long time, or is to be
moved to another place, it will be necessary to defrost the unit and
dry the interior.
IMPORTANT:
1. Disconnect the cooler from the power supply by removing the
power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent
mold, mildew and unpleasant smells.
• Do not touch the power plug
when your hands are wet.
• Never unplug the unit by
pulling on the plug.
CAUTION: Store the unit out of the reach of children. If you have
children, you may want to take additional precautions such as
removing the door to prevent a child from being trapped inside the
cooler!
EdgeStar Beverage Cooler
10
CLEANING AND MAINTENANCE
Periodic cleaning and proper maintenance will ensure efficiency, top
performance, and long life.
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and
lukewarm water solution such as 2 tablespoons of baking soda to 1 quart
of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and
rinse with clean water. Wipe with a soft clean towel to prevent water
spotting. If the door panel is stainless steel, it can discolor when exposed
to chlorine gas and moisture. Clean stainless steel with a cloth dampened
with a mild detergent and warm water solution. Never use an abrasive or
caustic cleaning agent.
Interior Cleaning
The beverage cooler’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and beverages.
6. Reconnect power to the unit.
TROUBLESHOOTING
Before Calling for Help
If the unit appears to be malfunctioning, read through the OPERATION
section of this manual first. If the problem persists, check the
Troubleshooting Guide below and on the following page. The problem
could be something that can easily be solved or explained.
Symptoms
The beverage cooler
turns on and off
frequently.
11
Possible causes
Solutions
The room temperature is
higher than the
recommended ambient
environment.
Run the cooler at the appropriate ambient temperature.
The door is being opened
often.
Minimize the number of times the door is opened.
The door is not completely
closed.
Make sure the door is completely closed.
The door gasket is not
sealing properly.
Make sure the door gasket is properly sealing.
The cooler does not have the
suggested ventilation.
Read and follow the “Installation Clearance
Requirements” section.
Troubleshooting Continued
Issue
The beverage cooler
does not turn on.
The beverage cooler will
not reach the desired
temperature
Possible cause
Solution
There is a power failure.
Ensure the cooler is plugged in and the power outlet has
power.
The cooler is not plugged in.
Plug the unit in to a power outlet that has sufficient
amperage.
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in your fuse box or reset the
breaker.
The cooler is placed too
close to a heat source.
Keep the cooler away from direct sun light or other heat
sources.
The cooler does not have
sufficient ventilation.
Read and follow the “Installation Clearance Requirements”
section.
The door is opened too
frequently or for a long
period of time.
Close the door tightly and do not open the door too
frequently or for a long period of time.
Certain sounds are normal.
Read the “Normal Sounds” section.
The unit is not level or is
touching another appliance.
Check to make sure that the cooler is level, and that it is
not in contact with another appliance or furniture.
The unit is not grounded
properly.
Contact your local electrician to test your electrical
grounding system.
The environment is humid.
Though the unit uses an “auto-defrost” system, under
certain conditions, manual defrosting may be required. If
frost builds up, you can try running the cooler on a warmer
temperature setting, minimizing the number of times you
open the door, or unplugging the unit to allow the frost to
melt.
The beverage cooler is
making strange noises
The body of the beverage
cooler is electrified.
Frost is forming in the
beverage cooler.
The ambient temperature is
too low.
The door is being opened
too frequently.
Your cooler is not level.
The door gasket is dirty.
The door will not shut
properly.
EdgeStar Beverage Cooler
Make sure the cooler is on a level surface.
Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is properly installed.
The shelves are incorrectly
installed.
Correctly install the shelves.
12
Troubleshooting Continued
Issue
Display shows E1, E2 or
E7.
The display shows --.
The alarm sounds and
the temperature display
flashes.
13
Possible cause
Solution
E1 or E2 indicate that the
air temperature sensor has
failed.
Contact an EdgeStar customer service agent.
E7 indicates that the door
switch has failed.
Contact an EdgeStar customer service agent.
The display temperature is
out of the unit’s range.
The display can only show temperatures within the range of
16 - 99°F or 9 - 37°C.
The appliance door has
been open longer than 60
seconds.
Close the beverage cooler’s door.
There has been a lengthy
interruption to the unit’s
power supply.
Restore power to the unit.
The ventilation opening is
covered or there is a large
build-up of debris.
Clean the unit of any debris and make sure to maintain
minimal clearance requirements. Read and follow the
“Installation Clearance Requirements” section.
Specifications
Description of product
Beverage Cooler
Model
VBR440
Voltage/Frequency
AC 115V~60Hz
Amperage
1.7A
Input Power
180W
Color
White Cabinet; Stainless Steel
Door
Refrigerant
R600a, 1.66 oz.
Temperature Range
36 - 43ºF
Dimensions
(Height x Width x Depth )
58 1/8” x 23 1/2” x 24 1/4”
Weight
141 pounds
Note: Technical data and performance information is provided for
reference only.
Specifications are subject to change. Check the rating label on the
beverage cooler for the most accurate information.
EdgeStar Beverage Cooler
14
Limited Warranty: Full One-Year Parts and Labor
This product is warranted by EdgeStar and is subject to any conditions set forth as follows:
WHAT IS COVERED:
For a period of ONE (1) YEAR from the date of
original retail purchase, EdgeStar will repair or
replace any part free of charge including labor
that fails due to a defect in materials or
workmanship. Labor will be performed free of
charge at an authorized EdgeStar repair facility
and EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may
request a defective part be returned in
exchange for the replacement part. All
replacement parts or products will be new,
remanufactured, or refurbished. All products and
parts replaced by EdgeStar under warranty
service become the property of EdgeStar. After
the 12 month period, EdgeStar will no longer be
responsible for labor charges incurred or
replacement parts. All defective products and
parts covered by this warranty will be repaired or
replaced on a mail-in basis to an EdgeStar
authorized repair facility.
This warranty applies to the original purchaser
only, and only covers defects in workmanship
experienced during operation of the product
under normal service, maintenance, and usage
conditions. This warranty applies to the purchase
and use of this product in residential settings
within the United
States of America.
Exceptions: Commercial or Rental Use
Warranty
90 days labor and parts from date of original
purchase. No other warranty applies.
WHAT IS NOT COVERED- The following limitations apply to the
coverage of this warranty. This warranty does not cover:
-Labor charges for installation, setup or training to use the
product.
-Shipping damage, and any damage caused by improper
packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse,
including abnormal service, handling, or usage.
-Cosmetic damage such as scratches and dents.
-Normal wear and tear on parts or replacement of parts designed
to be replaced, e.g. filters, cartridges, batteries.
-Service trips to deliver, pick-up, or repair, install the product, or to
instruct in proper usage of the product.
-Damages or operating problems resulting from misuse, abuse,
operation outside environmental specifications, uses contrary to
instructions provided in the owner’s manual, accidents, acts of
God, vermin, fire, flood, improper installation, unauthorized
service, maintenance negligence, unauthorized installation or
modification, or commercial use.
-Labor, service transportation, and shipping charges for the
removal and replacement of defective parts, beyond the initial 12
month period.
-Products that have been modified to perform outside of
specifications without the prior written permission of EdgeStar.
-Products lost in shipment, or theft.
-Products sold AS IS or from an unauthorized reseller.
-Products that have had their serial numbers removed, defaced,
or with serial numbers that have been invalidated.
-Damage from other than normal household use.
-Replacement or repair of household fuses, circuit breakers, wiring
or plumbing.
-Damage to personal property from use of product.
-Damage from service other than from an authorized EdgeStar
repair facility.
-Hoses, knobs, lint trays and all attachments, accessories and
disposable parts.
-Any service charges not specifically identified as normal such as
normal service area or hours.
-Any special or consequential damages arising out of the use of
the product.
OBTAINING WARRANTY SERVICE: If you believe your product is defective, contact EdgeStar Customer Support for
troubleshooting assistance and warranty service at www.edgestar.com or call 1-866-319-5473. Before contacting
Customer Support you are required to have your model number, serial number and proof of purchase available upon
request. Once an EdgeStar authorized representative has confirmed that your product is defective and eligible for
warranty service, the product must be returned to an EdgeStar authorized repair facility. EdgeStar is not responsible for
damage resulting from shipper mishandling or improper packaging. Do not return a defective product to the place of
purchase. Products received without a return authorization number will be refused.
THISWARRANTYISINLIEUOFANYOTHERWARRANTY,EXPRESSORIMPLIED,INCLUDINGWITHOUTLIMITATION,ANYWARRANTYOFMERCHANTABILITYOR
FITNESSFORAPARTICULARPURPOSE.TOTHEEXTENTANYIMPLIEDWARRANTYISREQUIREDBYLAW,ITISLIMITEDINDURATIONTOTHEEXPRESSWARRANTY
PERIODABOVE.NEITHERTHEMANUFACTURERNORITSDISTRIBUTORSSHALLBELIABLEFORANYINCIDENTAL,CONSEQUENTIAL,INDIRECT,SPECIAL,OR
PUNITIVEDAMAGESOFANYNATURE,INCLUDINGWITHOUTLIMITATION,LOSTREVENUESORPROFITS,ORANYOTHERDAMAGEWHETHERBASEDIN
CONTRACT,TORT,OROTHERWISE.SOMESTATESDONOTALLOWTHEEXCLUSIONOFINCIDENTALORCONSEQUENTIALDAMAGES,SOTHEABOVEEXCLUSION
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: service@edgestar.com
Register your product, download owner’s manuals, access additional troubleshooting
resources, and obtain more information on other great EdgeStar products on the web at:
http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2015 Living Direct, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising