EdgeStar | KC7000SSODTRIP | Owner Manual | EdgeStar KC7000BLTWIN - Full Size Dual Tap Kegerator Owner Manual

EdgeStar KC7000BLTWIN - Full Size Dual Tap Kegerator Owner Manual
Built-In Kegerator
BR7001SS / BR7001SSOD
BR7001BL
Refrigerators for the KC7000 Series of Kegerators
Owner’s Manual
For more information on other great EdgeStar products on the web, go to https://www.edgestar.com
To use the EdgeStar self-diagnostic tool, go to https://support.edgestar.com
V2.4-07132018
Important Safety Information
Improper handling can cause serious damage to the EdgeStar kegerator and/or injury to the
user. This kegerator is designed for domestic use only. Do not use the unit for industrial or
commercial use. Any other use may invalidate the warranty. Please review the ratings label
located on the rear panel of the unit for electrical and other technical data related to this unit.
The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire,
electric shock, or injury.
Electrical Safety



















Do not exceed the power outlet ratings.
It is recommended that the kegerator be connected on its own circuit.
The unit must be installed in accordance with state and local electrical codes.
A standard electrical supply (115 V, 60 Hz), that is properly grounded in accordance with the
National Electrical Code and local codes and ordinances is required.
Use outlets that cannot be turned off by a switch or pull chain.
Always turn the unit off and unplug it from the outlet when cleaning.
Unplug the unit if it is not going to be used for an extended period of time.
Do not operate the unit with a power plug missing the ground plug, a damaged cord, or a loose
socket.
Be sure the kegerator is properly grounded.
Never plug or unplug the unit with wet hands.
Do not bypass, cut, or remove the grounding plug.
Do not use extension cords or power strips with this unit. You may need to contact your electrician if
it is necessary to use a longer cord or if you do not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other appliances.
Do not start or stop the unit by switching the circuit’s power on and off.
If the power cord is damaged, it must be replaced by the manufacturer or a qualified technician.
Never repair the unit while it is plugged in.
Immediately unplug the unit if it makes strange sounds, emits smells, or smoke comes out of it, and
contact customer service.
Do not remove any part of the casing unless instructed to do so by an authorized technician.
You should never attempt to repair the unit yourself.
Contact customer service for service options if the unit needs service.
Note: Flammable Refrigerant Used! When handling, moving, and using the refrigerator: make
sure to avoid either damaging the refrigerant tubing, or increasing the risk of a leak.
i.
General Safety



















To prevent back and other types of injuries, use at least two people to move and install the
kegerator.
This unit is not intended for use by persons, including children, with reduced physical, sensory, or
mental capabilities, unless they have been given supervision or instruction concerning the use of
the appliance by the person(s) responsible for their safety.
Install the unit in a well-ventilated area where the ambient temperature is above 50°F and below
95°F.
The temperature range for this kegerator is optimized for beverage storage. Perishable food items
may require a different storage environment.
Do not place hot or warm items into the kegerator before they cool down to room temperature.
This unit is designed to be installed indoors (except for the BR7001SSOD), and protected from rain,
sleet, snow and/or moisture (all units).
This unit is not intended to be used by children.
Children should be supervised to ensure that they do not play with this product.
Never allow children to crawl inside the kegerator. If disposing of the unit, remove the door.
Do not use this unit near flammable gas or combustibles, such as gasoline, benzene, thinner, etc.
Do not place the unit near heat sources such as ovens, grills, or direct sunlight.
Only use in an upright position on a flat, level surface and provide proper ventilation.
Do not pinch or kink the power supply line between the unit and cabinet.
Do not leave any cleaning solutions in the unit.
Do not use solvent-based cleaning agents or abrasive solutions to clean the unit as they may
damage the interior and exterior.
Do not place any other appliances on top of the unit.
Do not turn the unit upside down, on its side, or at an angle off level.
If your model is equipped with a lock, take care to keep the keys away from children.
Do not move the unit without emptying the contents and securing the door in a closed position.
Note: This owner’s manual is provided for reference use only. Specifications may change
without prior notice. Refer to the product label on the back of your kegerator for the latest
technical information.
2
Table of Contents
IMPORTANT SAFETY INFORMATION……………………………………………………………………………………... I
TABLE OF CONTENTS……………………………………………………………………………………………………….. 3
INTRODUCTION……………………………………………………………………………………………………………….. 4
PARTS IDENTIFICATION…………………………………………………………………………………………………….. 5
FRONT VIEW……………………………………………………………………………………………………………………… 5
BACK VIEW……………………………………………………………………………………………………………………….. 5
ACCESSORIES………………………………………………………………………………………………………………… 6
STANDARD ACCESSORIES………………………………………………………………………………………………………. 6
INSTALLING THE KEGERATOR…………………………………………………………………………………………….. 6
ELECTRICAL REQUIREMENTS……………………………………………………………………………………………………. 7
Recommended Grounding Method…………………………………………………………………………………………… 8
LEVELING THE KEGERATOR……………………………………………………………………………………………………… 8
INSTALLING THE STAINLESS STEEL DOOR HANDLE…………………………………………………………………………….. 8
INSTALLING THE CASTERS……………………………………………………………………………………………………….. 9
REVERSING THE DOOR SWING…………………………………………………………………………………………………... 9
FREE STANDING INSTALLATION………………………………………………………………………………………………….. 11
Guard Rail……………………………………………………………………………………………………………………….. 11
Drip Tray………………………………………………………………………………………………………………………….11
BUILT-IN INSTALLATION…………………………………………………………………………………………………………... 12
Countertop Opening for Dispense Kit………………………………………………………………………………………… 12
Installation Requirements……………………………………………………………………………………………………… 13
Enclose Space Between Cabinet and Countertop………………………………………………………………………….. 14
KEG LOADING…………………………………………………………………………………………………………………. 15
OPERATION……………………………………………………………………………………………………………………. 16
INSTALLATION CHECK LIST BEFORE OPERATION……………………………………………………………………………….. 16
USING THE TEMPERATURE CONTROL PANELS………………………………………………………………………………….. 16
NORMAL SOUNDS………………………………………………………………………………………………………………… 17
DEFROSTING………………………………………………………………………………………………………………………17
PREPARING THE KEGERATOR FOR STORAGE…………………………………………………………………………………… 17
CLEANING AND MAINTENANCE…………………………………………………………………………………………… 18
EXTERIOR CLEANING…………………………………………………………………………………………………………….. 18
INTERIOR CLEANING……………………………………………………………………………………………………………… 18
TROUBLESHOOTING………………………………………………………………………………………………………… 18
SPECIFICATIONS………………………………………………………………………………………………………………20
EDGESTAR LIMITED WARRANTY………………………………………………………………………………..………….. 21
3
First Time Operating Instructions
Before use, make sure all packaging labels and materials are all removed from the unit. Be
sure to keep track of all included parts and pieces before discarding packaging materials. It
is advised that you keep the original box and packaging materials in case you are ever to
move or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling components
time to settle from transit. The instruction manual should be read before use.
Introduction
Thank you for purchasing this EdgeStar kegerator. We hope that this purchase will be the
beginning of a lasting and rewarding relationship between you and EdgeStar. We will provide the
customer support and exemplary products necessary to nurture that relationship.
This manual contains important information regarding the proper installation, use and
maintenance of your kegerator. Following this manual will ensure that your product will work at its
peak performance and efficiency.
Please save the original product packaging in case you need to safely transport your kegerator.
For Your Records:
Please write down the model number and serial number below for future reference.
Both numbers are located on the ratings label on the back of your unit and are needed
to obtain warranty service. You may also want to staple your receipt to this manual as it
is the proof of your purchase, and is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
For a more efficient experience, please do the following before contacting customer service:

If you received a damaged product, immediately contact the retailer or dealer that sold you
the product.

Read and follow this instruction manual carefully to help you install, use, and maintain your
kegerator.

Read the troubleshooting section of this manual as it will help you diagnose and solve
common issues.

Visit us on the web at https:/www.edgestar.com to register your product, download product
guides, additional troubleshooting resources, and up-to-date information. You can also find an
interactive self-diagnostic tool at https://support.edgestar.com

If you need warranty service, our friendly customer service representatives are available via
email at service@edgestar.com or by telephone at 1 (866) 319-5473.
4
Parts Identification
Tip: Gather the model and serial number from the product label and write them down before
installing the kegerator.
Front View
Back View
5
Accessories
Your kegerator will come with a set of standard accessories. These include a drip tray, guard
rail, guard rail installation pegs, door handle, casters, and dispense tower screws. The other
equipment / accessories you receive for the dispense kit and CO2 tank will be based upon the
type of kegerator you purchased.
Standard Accessories
(1) Drip Tray
(1) Door Handle
(Not included
with BR7001BL)
(1)Guard
GuardRail
Rail
(1)
(4) Casters
(Includes 16
screws for
installation)
(4) Guard Rail
Installation Pegs
(4) Dispense
Tower Screws
(For attaching
dispense tower
to cabinet)
Note: The variation of kegerator you purchase will determine the type of accessories you will
receive for the dispense kit. The most common options include single, dual, and triple taps.
Installing the Kegerator
The kegerator should be installed in accordance with local electrical code requirements. The
6
kegerator should also be placed in a location that is strong enough to support its total weight,
keeping in mind that it will weigh substantially more when fully loaded than when empty.
Before you plug the kegerator into a power supply, be sure to let it stand upright for at least 24
hours to allow the compressor’s oils to settle.
Unpacking the Kegerator
Warning: Use two or more people to move and install the kegerator. Failure to do so can result
in back or other injury.
Carefully remove the packaging materials. Remove any shipping tape and glue from your
kegerator before using. Do not use sharp instruments, rubbing alcohol, flammable fluids, or
abrasive cleaners to remove tape or glue. These products can damage the surface of your
kegerator.
Important: Do not remove any safety, warning, or product information labels from your
kegerator.
Electrical Requirements





ELECTRIC SHOCK HAZARD!
Plug into a grounded 3-prong outlet.
Never remove the grounding prong from the plug.
Never use an adapter to bypass the grounding prong.
DO NOT use an extension cord.
Failure to follow these instructions can result in fire, electrical shock, or death.
Before you move your kegerator into its final location, it is important to make sure you have the
proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in accordance with the National
Electrical Code and local codes and ordinances, is required.
It is recommended that a separate circuit, serving only your kegerator, be provided. Use
receptacles that cannot be turned off by a switch or pull chain.
The fuse (or circuit breaker) size should be 10 Amps or greater.
7
Recommended Grounding Method
For your personal safety, this appliance must be grounded. It is equipped with a power
supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord
must be plugged into a mating 3-pronged wall socket, and grounded in accordance with the
National Electrical Code and local codes and ordinances. If a mating wall socket is not
available, it is the personal responsibility of the customer to have a properly grounded, 3prong wall receptacle installed by a qualified electrician.
Leveling the Kegerator
It is important for the kegerator to be leveled in order to work properly. It can be raised or
lowered by rotating the plastic sheaths around each of the feet on the bottom of the machine. If
you find that the surface is not level, rotate the feet until the kegerator becomes level .You may
need to make several adjustments to level it. We recommend using a carpenter’s level to check
the machine.
1.
2.
Place a carpenter’s level on top of the product to see if the kegerator is level from front to
back and side to side.
Adjust the height of the feet as follows:
Turn the leveling feet to the right to lower that side of the kegerator.
Turn the leveling feet to the left to raise that side of the kegerator.
Important: Once you are ready to install it in a cabinet or directly on the floor, you must adjust
the feet to level the kegerator.
Installing the Stainless Steel Door Handle
BR7001SS, BR7001SSOD models only
To install a door handle:
1. Remove the four screws from the side of the door. This
should be the side opposite of the door hinge.
2. Place and align the openings of the handle hinges over the
screw holes in the side of the door.
3. Insert and tighten the screws to hold the handle in place.
8
Caution: Do not over-tighten the screws as this may cause damage to the handle or to the
stainless steel door.
Installing the Casters
This unit comes with four (4) casters. These are an optional accessary to assemble if you would
like to make the unit more mobile. To install the casters:
1. Remove the four leveling legs from the bottom of the unit.
2. Separate the front casters and back casters. The front casters have a lever for a brake lock.
3. Place the top plate of the caster over the area of the removed leveling leg and align the
opening to the screw hole openings.
4. Insert the screws to attach the caster to the cabinet.
5. Make sure the screws are tight so the caster is installed firmly.
Reversing the Door Swing
Important: Before you begin, unplug the kegerator.
Follow the instructions below to reverse the door swing.
To reverse the door from right swing to left swing:
1.
Open the door and, using a Phillips screwdriver, remove the bottom screws from the
lower hinge.
9
2.
Carefully slide the bottom of the door forward and down, and place it on a padded
surface to prevent damaging it.
3.
Remove the screws from the upper right hinge. Place the upper right hinge in a safe
place in case you need to reverse the door in the future. Remove the plastic caps from
the upper left hinge corner. Install the upper left hinge by fastening the screws through
the left hinge to the cabinet. Insert the plastic caps into the upper right corner.
4.
Remove the bottom right support bracket. Remove the plastic caps from the bottom left
hinge corner. Insert the plastic caps into the bottom right corner. Install the bottom left
support bracket from the plastic bag that was included with the instruction manual.
5.
Carefully insert the door into the upper left corner hinge. Install the lower hinge on the left
corner of the door.
6.
Slide the door on top of the lower hinge and secure the door by installing the lower
screws.
10
Free Standing Installation
Note: Please refer to the dispense kit installation guide to complete the full assembly of the
kegerator.
A free standing installation will allow you to install the kegerator in almost any place you desire.
Please follow the safety information referenced on the “Important Safety Information” page in this
manual.
Guard Rail
The guard rail helps to hold glasses on the top of the cabinet in order to avoid spills or
broken glass.
1.
2.
3.
Insert the four installation pegs on the outer edges of the top of the cabinet.
Place the guard rail onto the four installation pegs. You may need to push down on the
guard rail to ensure the rail has clicked into place on the pegs.
Screw the four small guard rail screws into the guard rail. This will lock the rail into
position.
Drip Tray
The surface mount drip tray is a reservoir designed to collect any runoff liquid from
overfilled glasses, leaking faucets, or spills. There are two pieces included for this tray.
Place it on top of the cabinet (or countertop) and position under the faucet(s).
11
Built-in Installation
Note: Please refer to the dispense kit installation guide to complete the full assembly of the
kegerator.
A built-in installation allows the kegerator to be placed under counter. This installation requires
several more steps and considerations than a free standing installation.
Countertop Opening for Dispense Kit
Important Notes:
 Choose a location that has ambient temperatures above 50°F and below 95°F. Operation
outside these temperatures may result in lowered efficiency or cause other adverse
effects.
 This unit MUST be installed in an area protected from the elements, e.g., wind, rain, water
spray, or drips.
 The kegerator should not be located next to ovens, grills, or other high heat sources.
 Do not kink or pinch the power supply cord between the kegerator and the wall or cabinet.
Once the location of the kegerator installation is determined the first step is to create an
opening in the counter for the dispense kit lines to pass through. Mark off a spot on the
countertop where the opening will be created. Align that spot so it will be directly above the
opening of the kegerator that will be placed under the counter. You will need to drill or cut
(depending on the material of your countertop) an opening into your counter the same size
as the opening of the top of the kegerator. Do not cut it larger than that size as the
dispense tower will be optimized for that size hole.
12
Installation Requirements
Once an opening is created in the countertop the next step is to install the cabinet. When
installing the kegerator under a counter, follow the recommended spacing dimensions shown
below.

Make sure the top cover, guard rail, drip tray, and installation pegs are NOT installed on
the top of the cabinet. These items will create an obstacle for the cabinet to be installed
under counter.

Move the kegerator so the opening on the top of the cabinet is aligned with the opening
in the counter.

The kegerator should be installed on a firm and level surface that will be able to support
the entire weight of a fully loaded unit. It is important for the kegerator to be level in
order to work properly. If needed, you can adjust the height of the kegerator by rotating
the feet. See the “Leveling the Kegerator” section.

A standard electrical supply (115 VAC only, 60 Hz), properly grounded in accordance
with National Electrical Code and local codes and ordinances is required.
13
Enclose Space Between Cabinet and Countertop
Once the cabinet is installed and the two openings of the cabinet and countertop are
aligned, you must seal off the open space that will be created above the kegerator cabinet
and under the countertop. If this open space is not properly sealed, the cabinet will lose its
cold air and allow warm air to enter. Similarly to leaving the kegerator door open, an
improper seal can result in kegerator performance issues such as temperature
inconsistency, foam problems, and excessive frost build up in certain cases.
To close the opening you will need to run a short connecting tube from the cabinet to the
countertop. There is not an accessory included for this connection with the unit. Common
materials for this connection include PVC pipe, insulated pipe tubing, or rubber lining
material. It is important to form a seal between the kegerator cabinet opening and the bottom
surface of the countertop. If you use PVC or foam tubing, your sealing apparatus may extend
from the interior of the kegerator cabinet up through the countertop and into the base of the
faucet tower.
Note: This installation tip applies to front vented, built-in capable kegerator models only.
Improper installation of a kegerator that is not intended for a built in application will result in
damage to your appliance.
14
Keg Loading



Half Barrel Keg
5 lb. CO2 tank
Double Gauge
Regulator




Slim Quarter Keg
Sixth Barrel Keg
5 lb. CO2 tank
Double Gauge
Regulator

Three Sixth Barrel
Kegs
5 lb. CO2 tank
Double Gauge
Regulator


15
Operation
Installation Check List Before Operation
1. Have all packing materials and tape been removed from the interior and exterior of the
kegerator?
2. Have the installation instructions been followed, including connecting the machine to electricity?
And has proper grounding been installed for the kegerator?
3. Has the machine been leveled?
4. Is the kegerator in a site where the ambient temperature is between 50ºF and 95ºF all
year round?
Using the Temperature Control Panels
Caution: If you power off the unit, please wait at least 5 minutes before powering it back on.
Use the up and down buttons to adjust the temperature. The temperature displayed can be in
Fahrenheit or Celsius. This kegerator has a temperature range from 32°F to 60°F.
This kegerator has one display. The unit will display the set temperature only. The kegerator also
has a memory function that allows the unit to revert back to the most recent set temperature in
the event of a power outage, or if the unit is manually powered off and back on.
Press the
button on the control panel to lower the temperature by a 1 degree increments.
Press the
button on the control panel to increase the temperature by a 1 degree increments.
Press the
button to turn the inner light on or off.
Press and hold the power button for approximately three (3) seconds to turn the unit’s power on
or off. The Run Light will illuminate when the unit is working.
The Celsius or Fahrenheit light will be lit depending on what scale temperature is being
displayed. To switch between C and F, press and hold the and
buttons at the same time for
approximately five (5) seconds until the temperature scale changes.
Note: Whether your kegerator can reach the actual set temperature depends on the ambient
environmental conditions.
16
Normal Sounds
Your new kegerator may make sounds that are not familiar to you. Most of the new sounds are
normal. Hard surfaces like the floor and walls can make the sounds seem louder than they
actually are. The following describes the kinds of sounds that might be new to you and what may
be making them.

Rattling noises may come from the flow of the refrigerant or the water line. Items stored on
top of the kegerator can also make noises.

The high efficiency compressor may make a pulsating or high-pitched sound.

Water running from the evaporator to the water bin may make a splashing sound.

As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your
kegerator.

You may hear air being forced over the condenser by the condenser fan.
Defrosting
Note that under most refrigerating settings, the unit will automatically defrost under most ambient
conditions. However, on colder settings, some frost may build up. Additionally, the more humid
the ambient conditions, the more frost may build up. Keep the door closed as much as possible
and avoid opening the door unnecessarily to minimize frost build-up.
If frost is preventing the door from closing properly, you may need to power the unit off until the
frost melts. Use a soft absorbent towel to dry the unit.
Warning: Never attempt to remove frost with a sharp object!
Preparing the Kegerator for Storage
If the kegerator will not be used for a long time, or is to be moved to another place, it will be
necessary to defrost the unit and dry the interior.
1.
2.
Disconnect the unit from the power supply by removing the power plug from the wall socket.
Leave the door open to allow for air circulation and to prevent mold, mildew, and unpleasant
smells.
Caution: Store the unit out of the reach of children. If you have children, you may want to take
additional precautions such as removing the doors to prevent a child from being trapped
inside the unit!
Important:
 Do not touch the power plug when your hands are wet.
 Never unplug the unit by pulling on the plug.
17
Cleaning and Maintenance
Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life.
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such
as 2 tablespoons of baking soda to 1 quart of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water.
Wipe with a soft clean towel to prevent water spotting. If the door panel is stainless steel, it can
discolor when exposed to chlorine gas and moisture. Clean stainless steel with a cloth
dampened with a mild detergent and warm water solution. Never use an abrasive or caustic
cleaning agent.
Interior Cleaning
The kegerator’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the doors and remove the contents.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reconnect power to the unit.
Troubleshooting
Before Calling for Help
If the unit appears to be malfunctioning, read through the “Operation” section of this manual first.
If the problem persists, check the Troubleshooting Guide below and on the following page. The
problem could be something that can easily be solved or explained.
Symptoms
The kegerator turns on and
off frequently.
The body of the kegerator is
electrified.
Possible Causes
The room temperature is
higher than the recommended
ambient temperature.
The door is being opened too
often.
The door is not completely
closed.
The door gasket is not sealing
properly.
Solutions
Run the unit at the appropriate
ambient temperature.
The unit is not grounded
properly.
Contact your local electrician
to test your electrical
grounding system.
18
Minimize the number of times
the door is opened.
Make sure the door is
completely closed.
Make sure the door gasket is
properly sealing.
Troubleshooting Continued
Symptoms
The Kegerator does not turn
on.
Possible Cause
There is a power failure.
The unit is not plugged in.
A house fuse has blown or
the circuit breaker is tripped.
The kegerator will not reach
the desired temperature.
The unit is placed too close to
a heat source.
The door is opened too
frequently or for a long period
of time.
The kegerator is making
strange noises.
Certain sounds are normal.
The unit is not level or is
touching another appliance.
Frost is forming in the
kegerator.
The space between the top of
the kegerator and bottom of
the countertop is not sealed
properly.
The environment is humid.
The ambient temperature is
too low.
The door is being opened too
frequently.
The door will not shut
properly.
Your unit is not level.
The door gasket is dirty.
The door gasket is not
installed correctly.
19
Solution
Ensure the unit is plugged in
and the power outlet has
power.
Plug the unit in to a power
outlet that has sufficient
amperage.
Replace the broken fuse in
your fuse box or reset the
breaker.
Keep the unit away from direct
sun light or other heat
sources.
Close the door tightly and do
not open the door too
frequently or for a long period
of time.
Read the “Normal Sounds”
section.
Check to make sure that the
kegerator is level, and that it is
not in contact with another
appliance, or furniture.
Reference the “Enclose Space
Between Cabinet and
Countertop” section in this
manual.
Though the unit uses an
“auto-defrost” system, under
certain conditions, manual
defrosting may be required. If
frost builds up, you can try
running the kegerator on a
warmer temperature setting,
minimizing the number of
times you open the door, or
unplugging the unit to allow
the frost to melt.
Make sure the unit is on a
level surface.
Clean the door gasket.
Make sure the door gasket is
properly installed.
Specifications
Note: Technical data and performance information are provided for reference only.
Description of
product
EdgeStar 24” Built-in
Kegerator
EdgeStar 24” Built-in
Indoor/Outdoor
Kegerator
EdgeStar 24” Built-in
Kegerator
Model
BR7001SS
BR7001SSOD
BR7001BL
Voltage / Frequency
AC 115 V~60 Hz
AC 115 V~60 Hz
AC 115 V~60 Hz
Amperage
1.5 A
1.5 A
1.5 A
Input Power
120 W
120 W
120 W
Color
Black Cabinet;
Stainless Steel Door
Stainless Steel
cabinet; Stainless
Steel Door
Black Cabinet; Black
Powder Coated
Stainless Steel Door
Refrigerant
R600a, 1.2 oz.
R600a, 1.2 oz.
R600a, 1.2 oz.
Temperature Range
32°F – 60°F
32°F – 60°F
32°F – 60°F
Dimensions
(Height x Width x
Depth )
Weight
34 3/8” X 23 13/16” X
27 3/8” **
34 3/8” X 23 13/16” X
27 3/8” **
34 3/8” X 23 13/16” X
27 3/8” **
99 lbs.
90 lbs.
99 lbs.
Specifications are subject to change. Check the rating label on the kegerator for the most accurate
information.
** Dimensions are for the fridge only including the handle. Depth without handle is 25 3/8”. Height with
casters and guardrail installed is 40 3/4”. See dimension guide for additional measurement information.
20
EdgeStar Limited Warranty
WHAT IS COVERED:
Full One-Year Parts and Labor
This product is warranted by EdgeStar and is subject to any conditions set forth as follows:
For a period of ONE (1) YEAR from the date of original retail purchase, EdgeStar will repair or replace any part free of charge including labor
that fails due to a defect in materials or workmanship. Labor will be performed free of charge at an authorized EdgeStar repair facility and
EdgeStar will supply new, rebuilt, or refurbished parts free of charge. EdgeStar may request a defective part be returned in exchange for the
replacement part. All replacement parts or products will be new, remanufactured, or refurbished. All products and parts replaced by EdgeStar
under warranty service become the property of EdgeStar. After the 12 month period, EdgeStar will no longer be responsible for labor charges
incurred or replacement parts. All defective products and parts covered by this warranty will be repaired or replaced on a mail-in basis to an
EdgeStar authorized repair facility.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during operation of the product
under normal service, maintenance, and usage conditions. This warranty applies to the purchase and use of this product in residential settings
within the contiguous United
States of America.
Exceptions: Commercial or Rental Use Warranty
90 days labor and parts from date of original purchase. No other warranty applies.
WHAT IS NOT COVERED- The following limitations apply to the coverage of this warranty. This warranty does not cover:
-Labor charges for installation, setup, or training to use the product.
-Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and any damaged caused by
improper voltage or any other misuse, including abnormal service, handling, or usage.
-Cosmetic damage such as scratches and dents.
-Normal wear and tear on parts or replacement of parts designed to be replaced, e.g. filters, cartridges, batteries.
-Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
-Damages or operating problems resulting from misuse, abuse, operation outside environmental specifications, uses contrary to instructions
provided in the owner’s manual, accidents, acts of God, vermin, fire, flood, improper installation, unauthorized service, maintenance
negligence, unauthorized installation or modification, or commercial use.
-Labor, service transportation, and shipping charges for the removal and replacement of defective parts, beyond the initial 12 month period.
-Products that have been modified to perform outside of specifications without the prior written permission of EdgeStar.
-Products lost in shipment, or theft.
-Products sold AS IS or from an unauthorized reseller.
-Products that have had their serial numbers removed, defaced, or with serial numbers that have been invalidated.
-Damage from other than normal household use.
-Replacement or repair of household fuses, circuit breakers, wiring or plumbing.
-Damage to personal property from use of product.
-Damage from service other than from an authorized EdgeStar repair facility.
-Hoses, knobs, lint trays and all attachments, accessories and disposable parts.
-Any service charges not specifically identified as normal such as normal service area or hours.
-Any special or consequential damages arising out of the use of the product.
OBTAINING WARRANTY SERVICE: If you believe your product is defective, contact EdgeStar Customer Support for troubleshooting
assistance and warranty service at www.edgestar.com or call 1-866-319-5473. Before contacting Customer Support you are required to have
your model number, serial number, and proof of purchase available upon request. Once an EdgeStar authorized representative has confirmed
that your product is defective and eligible for warranty service, the product must be returned to an EdgeStar authorized repair facility. EdgeStar
is not responsible for damage resulting from shipper mishandling or improper packaging. Do not return a defective product to the place of
purchase. Products received without a return authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD
ABOVE. NEITHER THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES
OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
IN NO EVENT AND UNDER NO CIRCUMSTANCE OF ANY TYPE OR KIND SHALL THE SELLER, MANUFACTURER AND/OR DISTRIBUTOR BE
LIABLE FOR ANY REASON, UNDER ANY THEORY, FOR MORE THAN THE BASIC COST OF THE PRODUCT TO THE PURCHASER OR END
USER. SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising