Ideal | Chip-Lok® LED CoB Array Holder, 50MM for Sharp/Magazen, Box of 500 | Instructions | Ideal Chip-Lok® LED CoB Array Holder, 50MM for Sharp/Magazen, Box of 500 instructions

Ideal Chip-Lok® LED CoB Array Holder, 50MM for Sharp/Magazen, Box of 500 instructions
Models
50-2101CR, 50-2102CR, 50-2303CR,
50-2103CT, 50-2204CT, 50-2100LG,
50-2100NC, 50-2103NC, 50-2100SH
50-2234C, 50-2102SL
CHIP-LOK® COB Array Holder
Installation Instructions
WARNING
Electrical Shock Hazard.
Contact with high voltage may cause falling, serious injury, or death. Disconnect power
before servicing. Never install holder without COB array. COBs manufactured by Edison,
Lextar, LG Innotek and Osram have exposed live components; use in Class 2 or SELV
applications only unless Luminaire provides sufficient electrical protection.
Electrical Fire Hazard.
Use in application exceeding voltage and current ratings listed can cause an electrical
fire resulting in serious injury or death. Only use in accordance with Table 1 and local
electrical wiring code.
For factory assembly into portable lamps and luminaires.
TABLE 1: Rated Wire (Use copper conductors only)
WIRE TYPE
C
US
Solid
18-24 AWG
0,25 - 1,0mm2
Tin Bonded
18-24 AWG
0,25 - 1,0mm2
Stranded
18 -22 AWG
0,50 - 1,0mm2
Voltage (except as noted below)*
250V*
150V*
Current (except as noted below)*
4A*
2A
110°C
T-110
Temperature
*COBs manufactured by Edison, Lextar, LG Innotek and Osram have exposed live components;
use in Class 2/SELV applications only unless Luminaire provides sufficient electrical protection.
Wire Insertion Instructions
1. Strip wires to 7 mm (1/4”-5/16”).
2. Grip wire firmly and push conductor into
wire port (Figure 1). Do not pre-twist
stranded wire. Gently pull conductor to
ensure proper insertion. Repeat with
other wires.
3. Use only one conductor per port and assure
that no copper is exposed on any of the
wires inserted.
Figure 1
7mm
Installation Instructions:
1. Preinstall M3 #4 or #5 pan head screws into
luminaire. (Except 50-2234C/50-2204CT)
2. Hold CHIP-LOK® holder in one hand;
LED array in other hand.
3. Locate and align the “+” marking on both
products.
4. Set LED array into holder so that the edge of
array touches side of spring leg.
(Figure 2)
5. Push array toward spring leg and down to
seat into holder. (Never install holder
without COB array.) Energizing luminaire
without COB array installed could cause
electrical shorting to heatsink.
6. Apply thermal paste/pad to array or heatsink
(Max. pad thickness of 0,5mm)
7. Insert holder/array assembly over screws
through keyways (Figure 3) and rotate holder
clockwise (Except 50-2234C/50-2204CT).
8. Tighten screw farther from spring leg first.
9. Torque screws to 0.3 – 0.5 N-m
(2.5 – 4.5 in-lb). Contact IDEAL for a proper
torque if using thread forming screws.
Removal of Wires:
1. Insert a 0.040 inch (1 mm) diameter pin in
to wire removal slot. (Figure 4)
2. Pull wire to release.
Figure 2
Figure 3
Figure 4
IDEAL INDUSTRIES GmbH
Gutenbergstrasse 10
D - 85737 Ismaning, Germany
+49-89-99686-0
germanysales@idealnwd.com
IDEAL INDUSTRIES LIMITED
Unit 3, Europa Court, Europa Boulevard
Westbrook, Warrington, WA5 7TN
United Kingdom
+44 (0) 1925 444446
electrical.enquiries@idealnwd.com
IDEAL INDUSTRIES SAS
Route de Gisy, • ZA Burospace – Bât 7
F – 91571 Bievres Cedex • Bièvres, France
+33 (0) 1 69 35 54 70
francesales@idealnwd.com
IDEAL INDUSTRIES, INC.
Becker Place • Sycamore, IL 60178, U.S.A.
+1-800-324-9571 Customer Assistance
oem@idealindustries.com
www.idealind.com ND 7868-9
IDEAL INDUSTRIES ASIA LIMITED 美国理想工业
Tel: 86-21-31263188 Ext: 209
Address: No.61, Lane1000, Zhangheng Road, Pudong District,
Shanghai, 201203, China
地址:上海市浦东新区张衡路1000弄61号 邮编:201203
U.S. Patent Nos. 9,146,027 & 9,249,955
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising