Elan | gSC2 | ELAN gSC2 Quick Install Guide | ELAN gSC2 Guide

ELAN gSC2 Guide
gSC2
Rear Panel Connections
Dimension: 8-1/2” W x 1-9/16” H x 5” D (half rack)
(215.9mm W x 39.69mm H x 127mm D)
Factory use
ONLY
WIFI Antenna
802.11 b/g/n
Serial
Connections
Sense Input
Connections
Relay
Connections
2 bi-directional RS-232 Ports
2 ELAN Sensor
input Ports
2 Normally Open Relays
12VDC 24VAC @ 1
AMP Compatibility
IR Outputs
USB Modem Connections
USB - See Integration Notes for compatible equipment
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
4 discrete IR channels.
Compatible with Xantech
single and dual emitters.
Ethernet Connection
Ethernet - 10/100 Mbps
PoE IEEE 802.3at Type 2
48 VDC, 600 mA
DC Power
Connection
Reset's the
unit's IP address
to factory default
(DHCP).
Press and hold
for programming
reset.
Cet émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d’antennes énumérés cidessous avec le gain maximal admissible et impédance
d’antenne requise pour chaque type d’antenne indiqué. Types d’antennes n’est pas inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type,
sont strictement interdits pour une utilisation avec cet appareil.
Peak Gain
Dipole Antenna
2.09dBi
®
Reset
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required
antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type,
are strictly prohibited for use with this device.
Antenna Type
gSC2
Quick Install Guide
Informations concernant l’exposition aux fréquences radio (RF):
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite ‘exposition aux fréquences radio d’Industry Canada (IC). Utilisez l’appareil de sans fil de
façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d’exposition aux
RF d’IC dans des conditions d’exposition à des appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d’une personne).
English
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves or other apparatus
(including amplifiers) that produce heat.
9. Only use attachments/accessories specified
by the manufacturer.
10. Unplug this apparatus during Iightning storms or when
unused for long periods of time.
11. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
FCC and IC Information:
This Class B digital apparatus complies with Part 15 of the
FCC rules and with Canadian ICES-003 and RSS-210.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation
of the device.
®
Cet appareil numérique de classe B est conforme aux normes
canadiennes ICES-003 et RSS-210. Son fonctionnement est
soumis aux deux conditions suivantes : (1) cet appareil ne doit
pas causer d’interférence et (2) cet appareil doit accepter toute
interférence, notamment les interférences qui peuvent affecter
son fonctionnement.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC and IC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment and meets the exemption
from the routine evaluation limits in section 2.5 of RSS 102.
1. This Transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment.
This equipment should be installed and operated
with a minimum distance of 20 centimeters from user
and bystanders.
Warning: The device meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102, and users can
obtain Canadian information on RF exposure and compliance
from the Canadian Representative Product Solutions Group
at Tel: (519) 763-4538.
Notice: Use only the antenna provided with the product:
R-SMA Antenna, Aristotle Enterprises Inc.
p/n RFA-02-L2M2-M10-N, gain of 2.0 dBi.
®
®
© 2013 Core Brands, LLC. All rights reserved. ELAN , g! and Panamax
are registered trademarks of Core Brands, LLC, a Nortek company.
P/N 9901333 Rev. E 05 /2014
HC4/HC8 INSTALLATION MANUAL
ELAN
2
To protect your equipment from power surges and momentary power interruptions we strongly
suggest you utilize a battery-backed power supply (UPS) with this equipment.
ELAN recommends Panamax UPS and power conditioning products for use with your new gSC2.
Unpack the gSC2. Verify that you have all packaging contents.
Serial Connections
5
Connect up to 2 RS-232 serial controlled devices using the
RS-232
Connections
(Continued)
included DB9 to RJ-45 adapters. The gSC2 serial outputs are not
compatible with RS-485 serial devices.
your shows
projectthe
requires
The tableIfbelow
568A and 568B color codes and the function of each conductor
RS-485 connections you will need
use a ports.
gSC10 Note
controller.
of thetoRS-232
that Comm ports one and two use pins two and three for
hardware handshaking. Some 3rd party devices require these connections.
See the Integration Notes for the devices you are connecting to determine which Comm
Ports
and DB9 to RJ45 adapters are appropriate
RS-232 wiring pin-outs are as
follows:
You should have received:
a. gSC2f. 1ea RJ-45 to serial DB-9
b. 12vDC Power Supply
null modem adaptor (P/N 8900599)
c. Wall mounting brackets
g. Relay wiring connector
d. Wall mounting hardware
h. WiFi antenna
e. 2ea RJ-45 to serial DB9 male adaptors i. Quick Install Guide (this document)
(P/N 8900597)
RS-232 Port Pin #
The g! Training Guide contains valuable hardware and software reference documentation and is considered
an important supplement to this document. You would have received the training guide while attending
568A Color Code
1
White/Green
2
Green
3
White/Orange
4
Blue
568B Color Code
White/Orange
Function
N/C
Serial
Orange
Connections
DCD
Blue RS-232 Ports
2 bi-directional
GND
White/Green
DTR
Sense Input
N/C
Connections
RTS
White/Blue
RXD
6
Orange
Green
TXD
TXD
Note: The gSC2 does not have a ViaNET connection. If your installation has devices that require
7
White/Brown
White/Brown
CTS
CTS
IR Outputs
ViaNET communication you will need to connect an ELAN SC1 to one of the serial RS-232 ports.
8
Brown
Brown
RTS
RTS
www.elanhomesystems.com
8
4 discrete IR channels.
Compatible with Xantech
single and dual emitters.
RS-232 Connections
The table shows the 568A and 568B color codes and the
function of each conductor of the RS-232 ports. Please refer to
the ELAN Integration Note for the specific device to determine
the proper RJ45 to DB9 adaptor to use.
Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus.
7
N/C
White/Blue
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
3
Shelf Mounting:
The gSC2 has rubber feet to protect finished surfaces.
Set the gSC2 in a location that will allow you to properly
manage connected wiring so that tension is not placed on the
connections. The gSC2 is relatively small and wire tension
will cause the unit to move and may cause wires to become
disconnected.
Wall Mounting:
The Wall Mounting Brackets included with the gSC2 attach to the
chassis using the included screws.
Do not use longer screws to attach the brackets as this may
permanently damage the gSC2. Utilizing the Wall Mount Brackets the gSC2 may be mounted in any orientation that suits your
installation.
Using the unit with the attached brackets as a template mark
the keyhole screw locations and the security screw locations.
Pre-drill all holes and insert only the keyholes screws. Hang the
gSC2 on the keyholes screws and then insert the security screws.
Structured Wiring Cabinet Mounting: Mounting the gSC2 in
a structured wiring cabinet is essentially the same as Wall
Mounting it. The difference is that you must supply mounting
screws that are short enough to not penetrate through the wall
behind the enclosure.
Relay Connections
Two normally open relays are available for controlling
Sense Input Connections
third party devices. The included removable connector will
accept up to The
16gaSense
bareInputs
copper
careful
verify
of theleads.
HC4 (2)Be
/ HC8
(4) aretoused
to conditionally execute macros and to
that no portiontrigger
of one
wire
touches
the
other
wire. Prior
to System Controller using the ELAN
Event
Maps
that have
been
programmed
into the
configuration
software. load does not exceed 24volts
connection verify
that the connected
AC/DC or 1amp.
If either parameter is exceeded, add a higher
When used with a conditional macro the sensor is connected to the device being
capacity relay to
control the
load and
use the software
gSC2 output
monitored.
The ELAN
configuration
can be to
used to create a macro that checks
control that relay.
the status of the sensor prior to issuing a command. This “conditional programming” can
be used to prevent a TV, for example, from being inadvertently turned on or off when
changing sources or turning a zone on or off.
4
Dimension: 8-1/2” W x 1-9/16” H x 5” D (half rack)
(215.9mm W x 39.69mm H x 127mm D)
Serial
Connections
2 bi-directional RS-232 Ports
2 bi-directional RS-232 Ports
Ethernet Connection
Connect
the
Ethernet
connection
to an available
10/100
Mbps
WIFI
Antenna
Relay
port on the network. This is the preferred connection.
802.11 b/g/n
Connections
The gSC2
may be powered over Ethernet (PoE). PoE connection
must meet IEEE 802.3at Type 2 requirements of up to 25W
(@50VDC
600mA Open
max). Relays
2 Normally
12VDC 24VAC @ 1
AMP Compatibility
WiFi Antenna
The gSC2 includes a WiFi radio for installations where
USB Modem
a hardwired
Ethernet Connections
connection is not available. This flexibility
allowsUSB
the- See
gSC2
to beNotes
usedfor as
both an
primary
Integration
compatible
equipment
controller and to act as an extender when necessary. Ethernet
connection is preferred, and should always be used when
Ethernet
Connection
available.
The WiFi
radio should be used sparingly and only in
Ethernet
- 10/100
Mbps
Extender
Mode. The
antenna
connector is a standard R SMA type
connector.
Use 802.3at
only antennas
PoE IEEE
Type 2 provided with the equipment
or as listed
on 600
pagemA
2 of this document. Configuring the WiFi
48 VDC,
radio may only be accomplished while the gSC2 is connected to
an Ethernet connection and is covered in the g! Configurator
reference guide.
2 ELAN Sensor
input Ports
DC Power
Connection
Reset
IR Outputs
the
4 discreteReset's
IR channels.
unit's
address
Compatible
with IP
Xantech
single andtodual
emitters.
factory default
(DHCP).
Press and hold
for programming
reset.
HC4/HC8 INSTALLATION MANUAL
ELAN
Mount the gSC2 in the desired location
The gSC2 is designed to mount on a shelf, hang in a cabinet
or rack, or mount in a structured wiring enclosure.
USB connection
Some accessories may be connected to the gSC2’s USB
connector. Refer to the ELAN Integration Note for the device prior
Serial
Sense Input
to connection.
Connections
Factory Connections
use
ONLY
(Ports 3 +)
5
the ELAN Dealer website at www.elanhomesystems.com and following the “dealer” link.
6
Function
GND
2 ELAN Sensor
input PortsRXD
g!School, however the g! Training Guide is updated regularly. Make sure you have the latest version by visiting
1
IR Output Connections
Four discrete IR outputs are supplied to control third party devices.
The outputs may be configured in g! programming to utilize a
carrier or not. Each output is compatible with Xantech single and
dual emitters.
© ELAN
2010
| All Connections
rights reserved.
Sense
Input
Event Maps can be programmed that execute a command or sequence of commands when
ELAN sensors acan
beInput
usedis to
input aForstatus
from
3rd party
Sense
triggered.
example,
a driveway
sensor can be used to activate an
ELANcan
contact
closure
sensor
to trigger
an Event
Mapto
that turns on the outside lights. The
devices. The status
either
be ON
or OFF.
This can
be used
sensor canofbeanused
to make
triggering of the Event Map conditional. If
trigger an eventstatus
map of
oraaslight
a condition
event
map.the
Connect
it is daytime
theports.
lights don’t come on. If it is nighttime, they do.
ONLY ELAN sensors
to these
Relay
Sense
Input
The HC4/HC8 provides +5 VDC to the TIP (VSNS) connection to power the Sensor. When
the Sensor is activated, it shorts the ring (SNS) to the
sleeve (GND) thereby triggering the
Connections
Connections
HC4/HC8’s Sense Input. See Figure 3-7.
Figure 3-7: Sense Inputs
9
RESET Switch
When pressed momentarily the RESET switch will clear the static IP setup and return the gSC2 to
DHCP as well as reset the WiFi configuration to factory default. When pressed and
held for more than 15 seconds the programming of the current version will be reset to
default. Pressing RESET while applying power will reset the software to the factory version.
WARNING! THIS CANNOT BE UNDONE!!!
TEST
The TEST connection is for factory and repair access only.
Do not plug anything into the TEST port. Plugging anything into
DC Power
Page 20 Factory use
the TEST port will void the warranty and release the magic smoke.
10
WIFI Antenna
Reset
Power Connection
11 Once all other connections have been completed, connect the
802.11 b/g/n
supplied 12VDC power supply and engage the power switch on
the front of the gSC2.
Reset's the
unit's IP address
Connecting to the gSC2 on your network
to factory
default
The gSC2 is set from
the factory
for DHCP networking, which
means it receives(DHCP).
its IP address from the network router.
Use g!Tools to find the address and connect to the gSC2.
2 ELAN Sensor
input Ports
2 Normally Open Relays
12VDC 24VAC @ 1
AMP Compatibility
IR Outputs
USB Modem Connections
USB - See Integration Notes for compatible equipment
4 discrete IR channels.
Compatible with Xantech
Ethernet Connection
Available ELAN sensors include: AUDIO, VIDEO, CONTACT CLOSURE,
andanddual
emitters. FIELD sensors.Ethernet - 10/100 Mbps
VOLTAGE, single
LED/LIGHT,
CURRENT/MAGNETIC
Available ELAN sensors include: AUDIO, VIDEO, CONTACT CLOSURE, and VOLTAGE,
LED/LIGHT, and CURRENT/MAGNETIC FIELD sensors.
PoE IEEE 802.3at Type 2
48 VDC, 600 mA
Connection
ONLY
12
13
Press and hold
Software upgrade
for programming
Prior to configuring the product, upgrade the gSC2 software to
reset.
the latest version of
g! Core Module. Core Module can be found
on the ELAN dealer website. The gSC2 is not compatible with g!
Core Module releases prior to g!7.0.
Relay
Connectio
2 Normally
12VDC 24
AMP Comp
USB Mod
USB - See
Ethernet
Ethernet PoE IEEE 8
48 VDC, 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising