Elan | EL-IP-OTF2-BK | Quick Start Guide | ELAN EL-IP-OTF2-BK Quick Start Guide

ELAN EL-IP-OTF2-BK Quick Start Guide
EL-IP-OTF2-WH
Quick Start Guide
QUICK START GUIDE
BEGINNING USING THIS CAMERA
IMPORTANT!!
If you are installing an ELAN Cameras and/or ELAN NVR with an
ELAN Controller, please refer to the “ELAN Surveillance” Integration
Note for setup and software configuration. E
LAN Integration Notes
are served through the ELAN tools and on elanhomesystems.com/
dealer-resources. The software configuration information in this
document can be used to extend device control parameters for use
within an ELAN controller environment, or be used to operate this
hardware independent of an ELAN controller.
NOTES
2
www.elanhomesystems.com
EL-IP-OTF2-WH
NOTE
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
contact techsupport@elanhomesystems.com
3
QUICK START GUIDE
Unit: mm
PART DESCRIPTION & DIMENSIONS
1
Upper cover
2
Lens
3
Infrared LED (IR LED)
4
Light sensor
5
RJ-45 Ethernet connector (supports PoE)
6
Power jack (DC12V ±10%)
7
Reset Wire (strip off the wire insulation if needed;
after the camera is reset, cut off the bare wire)
4
www.elanhomesystems.com
EL-IP-OTF2-WH
INSTALLATION
1. Retrieve the camera and remove the bottom bracket from the upper
cover with a hex key (FIG.1). Use the included screws (M4.0x25)
through the holes marked as “a,” and fix the camera in the desired
location (FIG.2 & FIG.3).
contact techsupport@elanhomesystems.com
5
QUICK START GUIDE
2. Attach the Ethernet and power cables to the RJ-45 connector and the
DC-in connector, respectively (FIG.4).
Connect the RJ-45 Ethernet cable with a waterproof connector
First, remove the waterproof connector and unscrew the waterproof nut.
Insert the Ethernet cable and connect to the RJ-45 connector with proper
tools (FIG.5). Then, tighten the waterproof connector and nut before the
RJ-45 connector is connected to the camera (FIG.6).
6
www.elanhomesystems.com
EL-IP-OTF2-WH
3. Secure the upper cover to the bottom bracket with a hex key FIG.7).
4. Adjust the pan, tilt, and azimuth of the camera to the desired location
(FIG.8). After the adjustment, tighten the screws to complete the
installation.
Make sure the light sensor is at the lowest side of the camera (FIG.1).
contact techsupport@elanhomesystems.com
7
QUICK START GUIDE
SYSTEM ARCHITECTURES
For connecting EL-IP-OTF2-WH Camera series to the network,
please follow one of the system architectures:
(1). Use DC12V power adaptor and network switch connected to a network.
EL-IP-OTF2-WH
(2). Use with PoE of the network switch connected to the network.
EL-IP-OTF2-WH
(3). Use PoE power injector and the network switch connected to the network.
EL-IP-OTF2-WH
8
www.elanhomesystems.com
EL-IP-OTF2-WH
EMERGENCY FACTORY DEFAULT
To restore the hardware to factory default settings, please follow these steps:
1. Short the “RESET wire” for 10 seconds before releasing.
2. The camera will be restored to factory default settings after approximately
90 seconds and will reboot automatically.
3. Search for the IP device using the IPScan software.
4. Start the IP device via an Internet browser.
5. Enter the default username “ELAN” and password “3526” to operate.
NOTE: Cameras are configured to use DHCP by default but will revert to the
default address 192.168.0.200 if a DHCP server is not available.
BEFORE ACCESSING IP CAMERAS
Before accessing the IP camera, make sure that the camera’s RJ-45 network,
audio, and power cables are properly connected. To set the IP address,
consult your network administrator for an available IP address. The default IP
address for each IP camera is 192.168.0.200. Users can use the default IP
address to verify the camera’s network connection.
contact techsupport@elanhomesystems.com
9
QUICK START GUIDE
SOFTWARE REQUIREMENTS
Universal ActiveX software components are required for online display of
MJPEG or H.264 Full HD video. When you log in to the IP camera from
Internet Explorer, a security warning dialog box will prompt the installation of
the Universal ActiveX plug-in. Click Install to download it.
10
www.elanhomesystems.com
EL-IP-OTF2-WH
INTERNET BROWSER SETTINGS
& APPLICATION REQUIRED
Make sure your Internet browser
allows the signed ActiveX plug-in to
work on your computer. To do this,
open Internet Explorer and go to
Tools-> Options-> Security Settings.
Set “Download Signed ActiveX
plug-in controls” to “Prompt” and
“Run ActiveX control and plug-in” to
“Enable”.
Once complete, you can access the
IP camera’s live video by entering the
default IP address via your Internet
browser. When the security warning
dialog box appears, click OK to
download the ActiveX plug-in directly
from the IP camera.
There are two levels of user authentication (admin and guest) that can
access the IP camera. Administrator is
authorized to reset basic mode settings
andsee live video, while the guest is
only allowed to see live video.
The default usernames
and passwords are as follows:
Username
ELAN
Password
3526
To log on to the IP camera, please enter the username and password on the login
page and click Submit to enter the system.
contact techsupport@elanhomesystems.com
11
main:
1 (800) 472-5555 - US
1 (707) 283-5900 - International
1 (707) 283-5901 - Fax
Core Brands, LLC, 1800 S McDowell Blvd., Petaluma, CA 94954, USA
©2017 Core Brands, LLC. All rights reserved.
ELAN is a registered trademark of Core Brands, LLC.
tech support:
techsupport@elanhomesystems.com
web:
elanhomesystems.com
10019569 Rev-A0, 11/2017
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising