Elan | EL-TSTAT-8810 | ELAN EL-TSTAT-8810 Manual | ELAN EL-TSTAT-8810 Manual

ELAN EL-TSTAT-8810 Manual
EL-TSTAT-8810
Owner’s Manual
TABLE OF CONTENTS EL-TSTAT-8810
TABLE OF CONTENTS
ABOUT YOUR NEW THERMOSTAT
Thermostat features____________________________________________________________________ 3
Controls & display overview_______________________________________________________________ 4
WI-FI SETUP________________________________________________________________ 5-6
OPERATION & PROGRAMMING
Select system mode (OFF/HEAT/EM-HEAT/COOL)________________________________________________ 7
Change temperature setting______________________________________________________________ 7
Select Event-Based™ air cleaning setting_____________________________________________________ 8
Reset service reminder messages__________________________________________________________ 8
Set time and day______________________________________________________________________ 9
Understanding program schedules_______________________________________________________ 9-10
Progressive recovery___________________________________________________________________ 10
Changing program schedules____________________________________________________________ 11
Program schedule overrides (temporary, permanent)__________________________________________12-13
WI-FI MAINTENANCE AND TROUBLESHOOTING
Accessing Wi-Fi settings menu_________________________________________________________14-15
Clearing router settings_________________________________________________________________ 15
Disabling the Wi-Fi radio________________________________________________________________ 16
Troubleshooting Wi-Fi connection________________________________________________________16-17
WARRANTY
Limited warranty and registration__________________________________________________________ 18
2
www.elanhomesystems.com
FEATURES EL-TSTAT-8810
ABOUT YOUR NEW THERMOSTAT
THERMOSTAT FEATURES
• Remote access and control over Wi-Fi.*
• Event-Based™ Air Cleaning.
• Large, clear, backlit display is easy to read
– even in the dark.
• Displays room temperature, temperature setting,
and optional outdoor temperature.
• Built in compressor protection.
• Air filter and humidifier service indicators.
• Auto backlight (activated with first button press).
• 7 day programmability.
• Easy to use temperature control can override
program schedule at any time.
• Progressive recovery.
*Requires a Control System
DISCLAIMER
THANK YOU FOR PURCHASING THIS PRODUCT
For optimum performance and safety, please read these
instructions carefully before connecting, operating or adjusting
this product. Please keep this manual for future reference.
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may
be damaged by electrical spikes, surges, electric shock, lightning
strikes, etc. Use of surge protection systems is highly
recommended in order to protect and extend the life
of your equipment.
contact techsupport@elanhomesystems.com
SAFETY AND PERFORMANCE NOTICE
EIA/TIA-568-B termination (T568B) of cables is recommended
for optimal performance.
To minimize interference of the unshielded twisted pairs in the
CAT5e/6 cable do not run the HDBaseT/Cat5e/6/6a cabling with
or in close parallel proximity to mains power cables.
Do not substitute or use any other power supply other than the
enclosed unit, or a ELAN approved replacement.
Do not disassemble the unit for any reason. Doing so will void
the manufacturer’s warranty.
3
ABOUT YOUR NEW THERMOSTAT EL-TSTAT-8810
CONTROLS & DISPLAY OVERVIEW
CURRENT INDOOR TEMPERATURE
CURRENT TIME
OUTDOOR TEMPERATURE (OPTIONAL)
SYSTEM MODE
SETTING
TEMPERATURE SETTING
EQUIPMENT STATUS
CLEAN AIR
SETTING
UP
SYSTEM MODE
DOWN
CLEAN AIR
HOLD
PROGRAM
INDICATORS SHOW THROUGH HOUSING
HEAT PUMP ONLY
EMERGENCY HEAT OR
AUXILIARY HEAT (RED)
SYSTEM FAULT (YELLOW)
Includes Event-Based ™ Air Cleaning
MAINTENANCE REMINDER
(YELLOW FLASHING)
COVER
QUICK REFERENCE CARD
CURRENT SCHEDULE PERIOD
MESSAGE CENTER
WI-FI SIGNAL STRENGTH
NOTE: BACKLIGHT IS ACTIVATED WITH FIRST BUTTON PRESS AND AUTOMATICALLY TURNS OFF.
4
www.elanhomesystems.com
WI-FI SET UP EL-TSTAT-8810
WI-FI SET UP
If you are not connecting your thermostat to a control system and plan to only control the unit from its touchpanel,
you do not need to enable WiFi.
To connect the EL-TSTAT-8810 thermostat to a Wi-Fi network follow the steps below.
Note: You will need a computer or mobile device with Wi-Fi and a web browser.
IMPORTANT
Setting up your thermostat with an ELAN Controller
If you are installing an ELAN Thermostat with an
ELAN Controller, please refer to the “ELAN Thermostat”
Integration Note for Wi-Fi setup and software
configuration. ELAN Integration Notes are served
through the ELAN tools and on elanhomesystems.com/
dealer-resources.
If you are planning to install the ELAN Thermostats
when an ELAN controller is not present, please follow
the instructions below.
contact techsupport@elanhomesystems.com
STEP 1
Verify the thermostat is in
Wi-Fi Connection Mode.
The thermostat by default will be in Wi-Fi Connection
Mode. To confirm that the thermostat is in Wi-Fi
Connection Mode, verify that the radio bars on the
thermostat are strobing as shown below.
Note: If the thermostat is not in Wi-Fi Connection Mode,
refer to the Owner’s manual for instructions on clearing
the Wi-Fi settings.
5
WI-FI SET UP EL-TSTAT-8810
WI-FI SET UP (Continued)
STEP 2
STEP 3
Connect to the thermostat using
a computer or mobile device.
Verify the thermostat is connected
to the Wi-Fi network.
On your computer or mobile device, scan for
available networks. The thermostat should appear as
ELANSTAT8810XXXX followed by a unique identifier,
corresponding to the last 4 digits of the MAC address.
Connect to the thermostat you want to configure.
Once all the required information is entered in the
web browser interface, the thermostat will connect to
the Wi-Fi network you selected. After the thermostat
is connected to the Wi-Fi network, the thermostat
will display the radio bars based on the Wi-Fi signal
strength. If the radio bars are not displaying the signal
strength, refer to Wi-Fi Maintenance and Troubleshooting
in the Owner’s manual.
If you are installing multiple thermostats, you can
determine the MAC address of the specific thermostat
you are trying to configure by removing the cover on the
front of the thermostat to access the MAC address label.
.
Open a web browser on your computer or mobile device.
In the browser enter:
http://192.168.1.99/elan.html
In the web browser interface select the network you
want to connect the thermostat to, and enter the
network’s security credentials
6
www.elanhomesystems.com
OPERATION & PROGRAMMING EL-TSTAT-8810
OPERATION & PROGRAMMING
When connected to an ELAN controller, it is recommended that you use the scheduling functions within
ELAN to control the thermostats. If you are installing thermostats outside of an ELAN environment, you can
use the programming functions described below.
SELECT SYSTEM MODE
(OFF/HEAT/EM-HEAT/COOL/AUTO)
Press
CHANGE TEMPERATURE SETTING
to select:
AUTO: Thermostat automatically selects heating or cooling depending
on the indoor temperature. “Auto” mode is not supported when
interfacing with an ELAN controller.
OFF: Heating and cooling systems are off.
HEAT: Thermostat controls only the heating system.
COOL: Thermostat controls only the cooling system.
EM-HEAT: Thermostat controls emergency/auxiliary heat.
Heat pump will not operate. (Only for heat pumps with auxiliary heat.)
contact techsupport@elanhomesystems.com
Press
or
current setting.
to adjust the
In AUTO use
to switch between
the HEAT and COOL setting.
7
OPERATION & PROGRAMMING EL-TSTAT-8810
OPERATION & PROGRAMMING (Continued)
SELECT EVENT-BASED™ AIR CLEANING SETTING
CIRC-30/HR: The air cleaner will run a minimum of
30 minutes every hour. The air cleaner will monitor
the amount of time your heating and cooling system
runs; if 30 minutes is not reached the air cleaner will
automatically turn on. This will maximize the amount of
air cleaning while minimizing energy consumption.
EVENT-3HR: When selected, the air cleaner will run
continuously and then return to the most recent mode of
AUTO, CIRC-30/HR, or ON-24/7. Use this option when
the air needs cleaning; an example would be while
vacuuming.
Press
to select:
ON-24/7: This option will provide the maximum amount
of air cleaning available. The air cleaner will be active for
24 hours a day seven days a week.
AUTO: Air cleaning will not occur for the sole purpose
of air cleaning, but will occur during fan operation for
heating and cooling.
8
ALLERGY-24HR: When seasonal allergies spike and
outside air quality is at its worst, choose this option.
Your air cleaner will run continuously for 24 hours
and then return to the most recent mode of AUTO,
CIRC-30/HR, or ON-24/7.
RESET SERVICE REMINDER MESSAGES
Press and hold
and
together for three
seconds to reset a service reminder message.
www.elanhomesystems.com
OPERATION & PROGRAMMING EL-TSTAT-8810
OPERATION & PROGRAMMING (Continued)
SET TIME AND DAY
Note: If configured to do so, the home automation
system can send periodic time updates to the
thermostat. If the thermostat is configured to be
used with an ELAN account the thermostat’s time
and date will be updated periodically, and will update
automatically for daylight savings.
to enter time setting mode.
1. Press
The hour is flashing.
UNDERSTANDING PROGRAM SCHEDULES
The daily schedule is split into four sections:
WAKE: 6am-8am – Temperature you would prefer to
wake up to, until you leave for the day.
or
to adjust the hour.
2. Press
Press
,
the
minutes
flash. Press
3.
to adjust the minutes.
, the day flashes. Press
4. Press
to adjust day.
or
or
to end. “DONE” will display.
5. Press
The thermostat will return to normal mode if no key is
pressed within 3 seconds.
contact techsupport@elanhomesystems.com
LEAVE: 8am-5pm – Temperature when you are away
from the house during the day.
RETURN: 5pm-10pm – Temperature you would prefer to
return to, until bedtime.
SLEEP: 10pm-6am – Temperature you would prefer
during the night.
The times shown are the defaults. The start time and
temperature of each section can be changed to fit your
schedule (see page 11).
9
OPERATION & PROGRAMMING EL-TSTAT-8810
UNDERSTANDING PROGRAM SCHEDULES
Setpoint
Event
Event designator
Start time
Heat
Cool
1
WAKE
6:00AM
70°F (21°C)
78°F (25.5°C)
2
LEAVE
8:00AM
62°F (16.5°C)
85°F (29.5°C)
3
RETURN
5:00PM
70°F (21°C)
78°F (25.5°C)
4
SLEEP
10:00PM
62°F (16.5°C)
82°F (27.5°C)
PROGRESSIVE RECOVERY
The Progressive Recovery feature allows the thermostat
to activate the heating and cooling equipment prior to an
event in order to reach the desired temperature at the
start of the next scheduled event.
10
Example:
Set the WAKE time to 6 am, and the heat setpoint
to 70°F. The heat will come on before 6 am, so the
temperature is 70°F by the time you wake at 6 am.
www.elanhomesystems.com
OPERATION & PROGRAMMING EL-TSTAT-8810
CHANGING PROGRAM SCHEDULES
twice to enter program setting mode.
1. Press
Start time of the WAKE event is flashing.
5. Press
Press
or
to adjust the start time
2. Press
Press
,
HEAT
setting
flashes. Press
3.
or
to adjust the heat setting.
to advance the next event, and repeat
6. Press
steps 2-6 for LEAVE, RETURN and SLEEP events.
, COOL setting flashes. Press
4. Press
or
to adjust the cool setating.
contact techsupport@elanhomesystems.com
or
, CLEAN AIR/FAN setting flashes.
to adjust the clean air/fan setting.
to advance to the next day. Repeat
7. Press
steps 2-6 for each day of the week.
to end. “DONE” will display.
8. Press
The thermostat will return to normal mode if no button
is pressed in 3 seconds.
11
OPERATION & PROGRAMMING EL-TSTAT-8810
PROGRAM SCHEDULE OVERRIDES (TEMPORARY, PERMANENT, AWAY, HEAT BLAST)
TEMPORARY PROGRAM OVERRIDE
PERMANENT HOLD
Press
or
to immediately adjust
the temperature. This will temporarily override the
temperature setting for the current programmed time
period. The new temperature setting will be maintained
until the next time period of the programmed schedule.
Press
to permanently hold the temperature at
its current setting. This will override the temperature
settings for all time periods of the programmed
schedule. With the thermostat in permanent hold, the
thermostat temperature can be manually adjusted and
will stay at that setting until the hold is cancelled.
To cancel the temporary override, press
twice.
To cancel the permanent hold press
12
.
www.elanhomesystems.com
OPERATION & PROGRAMMING EL-TSTAT-8810
PROGRAM SCHEDULE OVERRIDES (TEMPORARY, PERMANENT, AWAY, HEAT BLAST)
AWAY
HEAT BLAST®
The Away feature, if enabled, allows the thermostat to
be set to a predefined setpoint(s) by simply pressing
the Away button in your home automation interface
(if supported). By default the cooling setpoint is 85°F
(29.5°C), the default heating setpoint is 62°F (16.5°C)
and the default clean air/fan mode is Auto. The default
settings can be modified in the home automation
interface (if supported).
The Heat Blast® feature will raise the current room
temperature by 3°F to 5°F based on the Installer
Setup, and then resume normal operation. To activate
a Heat Blast, press the Heat Blast button in the home
automation interface (if supported).
Note: Heat Blast can only be activated in the home
automation interface (if supported), and is only available
if it is enabled in the Installer Setup and the thermostat is
in Heat or Emergency Heat mode.
To cancel Heat Blast at the thermostat press
,
or the
or
buttons.
To cancel Away at the thermostat press
contact techsupport@elanhomesystems.com
.
13
WI-FI MAINTENANCE AND TROUBLESHOOTING EL-TSTAT-8810
ACCESSING WI-FI SETTINGS MENU
The following instructions explain how to enter the Wi-Fi
Settings menu and change settings. The table on page
15 describes each setting. Default settings are shown
in bold.
How to enter the Wi-Fi settings menu to change
settings.
Press and hold
and
for three seconds.
The screen will display the first setting.
Press
or
Press
to change to the next option.
to change the setting.
Press
after the last setting.
“DONE” will be displayed.
The thermostat will return to Normal mode if no button
is pressed in 60 seconds.
SETTING VALUE
WI-FI SETTING NUMBER
Includes Event-Based ™ Air Cleaning
14
www.elanhomesystems.com
WI-FI MAINTENANCE AND TROUBLESHOOTING EL-TSTAT-8810
ACCESSING WI-FI SETTINGS MENU
Factory default setting
(bold) and setting range
Wi-Fi setting
Description
47. Wi-Fi Disconnect and
Clear Settings
Disconnects the Thermostat from the router and clears the Wi-Fi
settings. Use this to set the thermostat back to provisioning mode so it
can be connected to a new Wi-Fi router.
0: No
48. T urn Wi-Fi Radio
On/Off
Use to turn the Wi-Fi radio on or off. Wi-Fi settings will be maintained
if the radio is set to Off.
0: Off
1: Yes
1: On
CLEARING ROUTER SETTINGS
If you purchase a new Wi-Fi router or change the security settings on your existing router the router settings in the
thermostat need to be cleared so the new Wi-Fi router settings can be entered. To do this, enter the Wi-Fi settings
menu as described in the Accessing Wi-Fi Settings Menu section on page 14. Change the setting for Wi-Fi Disconnect
and Clear Settings to Yes then press
three times, “DONE” will be displayed. This will remove all of the previous
Wi-Fi settings. Refer to Wi-Fi Setup on pages 5-6 for instructions on connecting the thermostat to your Wi-Fi Network.
contact techsupport@elanhomesystems.com
15
WI-FI MAINTENANCE AND TROUBLESHOOTING EL-TSTAT-8810
DISABLING THE WI-FI RADIO
To turn off the Wi-Fi radio on the thermostat, enter the Wi-Fi settings menu as described in the Accessing Wi-Fi Settings
Menu section on page 14. Change the setting for Turn Wi-Fi Radio On/Off to Off and then press
, “DONE” will
be displayed. This will turn off the Wi-Fi radio, but maintain all network settings. To turn the Wi-Fi radio back on simply
enter the Wi-Fi setting menu and change the setting for Turn Wi-Fi Radio On/Off to On and then press
, “DONE”
will be displayed.
TROUBLESHOOTING WI-FI CONNECTION
The Wi-Fi connection status is communicated through the use of the radio strength indicator. The following table
describes the various statuses and the corresponding radio bar display.
16
www.elanhomesystems.com
WI-FI MAINTENANCE AND TROUBLESHOOTING EL-TSTAT-8810
Wi-Fi connection status
Radio status indicator
Normal Operation.
Wi-Fi signal strength is indicated
by the appropriate number of bars.
The thermostat Wi-Fi settings have not been entered. Refer to
Wi-Fi Setup on pages 5-6 for instructions for entering the Wi-Fi
settings.
The frame is displayed and the bars cycle from 0 to 4.
The thermostat cannot connect to the Wi-Fi router. Verify that the
router is functioning properly.
The frame and all bars
flash on and off.
Indicates the thermostat was not configured properly when
connecting to the router. Confirm there is no IP conflict and
repeat Wi-Fi setup. Note: If the thermostat is configured to work
with an ELAN account this indicates that the thermostat cannot
connect to the ELAN web interface. Confirm that the internet
connection is working.
The display will alternate between displaying the frame and
all bars.
There is an internal error with the thermostat Wi-Fi radio. The
thermostat will continue to control the HVAC, but will not be able
to connect to Wi-Fi. Contact an HVAC professional for repair.
The frame will flash on and off.
Wi-Fi radio turned off. Refer to the Accessing Wi-Fi Settings
Menu section on page 14 for information about turning the Wi-Fi
radio on.
Not displayed.
contact techsupport@elanhomesystems.com
17
WARRANTY / FCC DECLARATION EL-TSTAT-8810
ELECTRONIC THERMOSTAT FIVE YEAR LIMITED WARRANTY
Your ELAN Thermostat unit is expressly warranted for five (5) years
from date of installation to be free from defects in materials or
workmanship.
ELAN’s exclusive obligation under this warranty shall be to supply,
without charge, a replacement for any thermostat which is found to
be defective within such five (5) year period and which is returned,
together with the date of installation, no later than thirty (30) days after
said five (5) year period by you to either your original supplier or to
Core Brands, Petaluma, CA 94954.
THIS WARRANTY SHALL NOT OBLIGATE RESEARCH PRODUCTS
CORPORATION FOR ANY LABOR COSTS AND SHALL NOT APPLY TO
DEFECTS IN WORKMANSHIP OR MATERIALS FURNISHED BY YOUR
INSTALLER AS CONTRASTED TO DEFECTS IN THE THERMOSTAT
ITSELF.
IMPLIED WARRANTIES OF MERCHANTABILITY OF FITNESS FOR
A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO
THE AFORESAID FIVE YEAR PERIOD. RESEARCH PRODUCTS
CORPORATION’S LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OTHER THAN DAMAGES FOR PERSONAL INJURIES,
RESULTING FROM ANY BREACH OF THE AFORESAID IMPLIED
WARRANTIES OR THE ABOVE LIMITED WARRANTY IS EXPRESSLY
EXCLUDED. THIS LIMITED WARRANTY IS VOID IF DEFECT(S) RESULT
FROM FAILURE TO HAVE THIS THERMOSTAT INSTALLED BY A
18
QUALIFIED HEATING AND AIR CONDITIONING CONTRACTOR. IF THE
LIMITED WARRANTY IS VOID DUE TO FAILURE TO USE A QUALIFIED
CONTRACTOR, ALL DISCLAIMERS OF IMPLIED WARRANTIES SHALL
BE EFFECTIVE UPON INSTALLATION.
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential
damages, so the above exclusions or limitations may not apply to you.
This warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
FCC DECLARATION
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
www.elanhomesystems.com
FCC DECLARATION / IC STATEMENT EL-TSTAT-8810
FCC DECLARATION (Continued)
IC STATEMENT
FCC Interference Statement (Part 15.105 (b))
RSS-GEN, Sec. 7.1.2
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is
not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d’un type et
d’un gain maximal (ou inférieur) approuvé pour l’émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir
le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée quivalente (p.i.r.e.) ne dépassepas l’intensité nécessaire à
l’établissement d’une communication satisfaisante.
RSS-GEN, Sec. 7.1.3
FCC RF Radiation Exposure statement
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
To comply with FCC/IC RF exposure limits for general population /
uncontrolled exposure, the antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with
any other antenna or transmitter.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
contact techsupport@elanhomesystems.com
19
main:
1 (800) 472-5555 - US
1 (707) 283-5900 - International
1 (707) 283-5901 - Fax
© 2017 ELAN® is a registered trademark of Core Brands, LLC.
tech support:
techsupport@elanhomesystems.com
web:
elanhomesystems.com
10018964 Rev-A0, 10/2017
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising