URC | MRX-2 | Owners manual | URC MRX-2 Owners Manual

URC MRX-2 Owners Manual
Owner’s Manual
MRX-2
Network Base Station
MRX-2 Owner’s Manual ©2014 Universal Remote Control, Inc.
The information in this manual is copyright protected. No part of
this manual may be copied or reproduced in any form without prior
written consent from Universal Remote Control, Inc.
UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR
OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS
MADE IN THIS MANUAL.
The information in this manual may be subject to change without
prior notice.
Total Control is a registered trademark of Universal Remote Control,
Inc.
Complete Control is a registered trademark of Universal Remote Control,
Inc.
URC - Control the Experience is a registered trademark of Universal
Remote Control, Inc.
All other brand or product names are trademarks or registered
trademarks of their respective companies or organizations.
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: (914) 835-4484 Fax: (914) 835-4532
TABLE OF CONTENTS
Introduction
1
Features and Benefits
2
Parts Guide
3
Front and Rear Panel Descriptions
4
Network Installation
6
Specifications
7
Limited Warranty Statement
8
End User Agreement
10
Federal Communication Commission Interference Statement
11
Declaration of Conformity
12
MRX-2 NETWORK BASE STATION
Introduction
The MRX-2 Network Base Station allows for control of your
components by sending infrared and serial commands to your system.
This base station can be used with either a Total Control or a
Complete Control system.
When used in a Total Control System:
Expand zones throughout the home or commercial space by
installing multiple MRX-2’s.
Control equipment such as shades and TV lifts using the base
stations sensors, relays and RS-232 ports.
Control URC RF Lighting using the optional RFTX-1 transmitter.
When used in a Complete Control System:
The MRX-2 is required to use the CC Control App for iOS devices,
like the iPad and iPhone.
Extend control to other rooms by installing multiple MRX-2’s
throughout the home or commercial space.
The MRX-2 offers traditional IR only control from compatible
URC MX series remotes via an optional RFX-250.
Page 1
MRX-2 NETWORK BASE STATION
Features and Benefits
When used in a Total Control System:
Expand Control: Add an MRX-2 to a Total Control system to
expand control to other rooms/areas in the home or office.
Components located out of reach from the MRX Advanced
Network System Controller may be controlled via IR, RS-232 or
Relays by using an MRX-2 to expand the scope of a Total
Control system.
Lighting Control: By connecting an optional RFTX-1 RF
Transmitter, take control of your URC lighting (within range).
Control a specific light, a whole room or even the entire home
from any remote control or iOS device.
When used in a Complete Control System:
Enables iOS Control: The addition of an MRX-2 base station to
a control system, allows for control via URC’s CC Control iOS
app for iPads, iPhones and iPod touch. Each iDevice requires
programming by a qualified custom install professional.
Note: Requires the purchase of CC Control Setup code (one
code per system).
No Aiming: Using a base station results in flawless control of
your components without having to aim the remote! The signal
travels to the base station via RF or Wi-Fi and is then converted
back to infrared before being sent to the device being
controlled; perfect for hidden components.
Note: An optional RFX-250 Antenna is required for use with
URC remote controls.
Page 2
MRX-2 NETWORK BASE STATION
Parts Guide
The MRX-2 Network Base Station includes:
1 - MRX-2 Network Base Station
1 - 12V-1000mA Power Supply
6 - Visible Emitters with 10 foot plug
in cables including 1 pink sleeved
emitter for the RFTX-1 port
1 - Two Meter 3.5mm Stereo to
3.5mm Stereo (for daisy chaining
multiple MRX-2 with one RFX-250)
1 - Adjustment Tool
1 - Mounting Plate for wall mounting
the MRX-2
Page 3
MRX-2 NETWORK BASE STATION
Front and Rear Panel Descriptions
Front
The front panel consists of 4 indicator lights which will illuminate
when in use.
Power
Status
Sensor
Ethernet
Reset: Bottom
Power: Illuminates when the power supply is connected to an outlet.
Status: Flashes blue when an RF or Network signal is received.
Sensor: Illuminates to indicate when the sensor is activated.
Ethernet: Illuminates when connected to an active network.
Reset: Press the Reset button located under the MRX-2 to restart the
unit.
Page 4
MRX-2 NETWORK BASE STATION
Rear
The rear panel ports are:
Power
Relay:NO,
NC, COM
IR Outputs: #1-6
RFTX Port: #6
Sensor
Ethernet RS-232 Ports
IR IN
RF IN
RF ID
RF Out
Power: Uses the included 12V/1Amp power supply.
LAN: Plug an ethernet cable (RJ45) to the LAN(Local Area network).
Relay NO, NC, COM: Configurable switch closure control.
RS-232 Ports: Two RS232 ports provide direct control.
Sensor: Connect with one of URC’s or compatible third party,
sensors.
IR IN: Allows MRX-2 control from a base station such as a MRF-260.
Note:IR Routing is lost from commands received from this input.
IR Outputs: Connect emitters for IR control of connected devices.
RFTX Port: Dual port #6 for the RFTX-1 connecting cable or
included sleeved IR emitter.
RF IN: Connects to an optional single RFX-250 (Only for MX series
products.)
RF Out: Used for daisy chaining MRX-2s for RF Operation (Refer to
the RFX-250 manual.)
RF ID: 15 unique RF ID's provide RF control and routing to multiple
MRX-2’s in the same home.
Note: DO NOT USE RF ID #0, as it is the interference "sniffer", used
to detect RF interference in the area.
Page 5
MRX-2 NETWORK BASE STATION
Network Installation
The MRX-2 can be installed in either a Total Control or a Complete
Control System. Connect the Ethernet cable (RJ45) to the rear of the
MRX-2 and the other end to the active network.
Total Control Install
Complete Control Install
Page 6
MRX-2 NETWORK BASE STATION
Specifications
Network: One 10/100 Ethernet port
Relay: One relay configurable to be NO, NC or Momentary
Sensor: One sensor supports Video or Voltage sensing via URC
sensors.
RS-232: Two RS-232 ports support TX, RX and GND two way
communication via URC cables.
IR: Six adjustable IR ports enable the included URC emitters to
control IR devices Note: 6th IR Output requires the included
sleeved emitter (identified by a pink connector), since it can
optionally be used to connect an RFTX-1
Weight: 8.4 oz.
Size: 248 x 120mm x28mm
Power: 12V External Power Supply
Page 7
MRX-2 NETWORK BASE STATION
Limited Warranty Statement
1. LIMITED WARRANTY AND DISCLAIMERS
Universal Remote Control, Inc. (“URC”) warrants that URC
equipment purchased directly from URC or from an authorized URC
dealer or distributor shall be free from defects in material and
workmanship under normal usage for a period of one (1) year from
the date of purchase of the product by the end-user, but no longer
than thirty-six (36) months from the date of shipment of the URC
equipment by URC to an authorized URC dealer or distributor,
except that with respect to Total Control® whole-house products, the
warranty extends for two (2) years from the date of purchase by the
end-user, but no longer than forty-eight (48) months from the date of
shipment of the URC equipment by URC to an authorized URC
dealer or distributor.
This limited warranty is valid only in the United States of America.
URC equipment purchased from other than an authorized URC
dealer or distributor is without warranty.
URC warrants that the software will substantially conform in any
material respect to its functional specifications at the time of delivery.
URC SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR
EDITORIAL ERRORS AND/OR OMISSIONS MADE IN THE URC
DOCUMENTATION. URC DOES NOT WARRANT THAT THE URC
SOFTWARE IS BUG-FREE OR ERROR FREE OR THAT THERE ARE
NO ERRORS/BUGS IN THE URC SOFTWARE.
URC warrants that at the time of purchase the URC equipment and
the URC software complied with all applicable regulations and
policies of the Federal Communications Commission ("FCC")
regarding electromagnetic interference caused by
electronic/computing devices and to the extent that the URC
equipment and/or the URC software fails to so comply, URC shall, at
its own expense, take all reasonable measures to promptly cause
such to comply.
THIS LIMITED WARRANTY DOES NOT COVER TECHNICAL
ASSISTANCE FOR HARDWARE OR SOFTWARE USAGE EXCEPT AS
EXPRESSLY PROVIDED FOR HEREIN.
CERTAIN IMPLIED WARRANTIES, INCLUDING AN IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, MAY BE AVAILABLE WITH RESPECT TO
URC EQUIPMENT. IMPLIED WARRANTIES VARY FROM STATE TO
STATE. URC EXPRESSLY LIMITS THESE IMPLIED WARRANTIES, TO
THE EXTENT ALLOWABLE BY LAW, TO THE TIME PERIODS
COVERED BY THE EXPRESS WRITTEN WARRANTIES PROVIDED
HEREIN. OTHERWISE AND EXCEPT AS PROVIDED FOR HEREIN,
URC EXPRESSLY DISCLAIMS ALL WARRANTIES, EXPRESS,
STATUTORY OR IMPLIED, AND MAKES NO REPRESENTATIONS
REGARDING THE USE OF, OR THE RESULTS OF THE USE OF, THE
EQUIPMENT, SOFTWARE OR DOCUMENTATION IN TERMS OF
CORRECTNESS, ACCURACY, RELIABILITY OR OTHERWISE.
Page 8
MRX-2 NETWORK BASE STATION
EXCEPT AS EXPRESSLY PROVIDED FOR HEREIN, TECHNICAL
SERVICES ARE SUPPLIED "AS IS", WITHOUT ANY WARRANTY,
EXPRESS, STATUTORY OR IMPLIED, OF ANY KIND. TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, URC
EXPRESSLY DISCLAIMS ALL WARRANTIES RELATING TO
TECHNICAL SERVICES, EXPRESS, STATUTORY OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
QUALITY OR REASONABLE SKILL AND CARE, OR OUTCOME OR
RESULTS.
WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE
OTHER PROVISIONS HEREIN, THIS LIMITED WARRANTY DOES
NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT OR ACTS OF
NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH THIRD
PARTY CONTENT, OR (IV) BEYOND THE WARRANTY PERIOD
AND/ OR FAILURE TO FOLLOW URC WARRANTY CLAIM
PROCEDURE.
The warranty limitations and warranty disclaimers may not apply to
end user in whole or in part, where such are restricted or excluded
by applicable law, and such shall apply to the maximum extent
permitted by applicable law.
In the event of any warranty claim, URC will, at its sole option,
repair the URC equipment using new or comparable rebuilt parts, or
exchange the URC equipment for new or rebuilt equipment. In the
event of a defect, these are the end user's exclusive remedies.
All the URC equipment returned for service, exchange or repair
require an RGA number. To obtain an RGA number, you must
complete a Return Request Form which you may obtain by calling
(914) 835-4484 or contacting URC at
returnrequest@universalremote.com. To obtain warranty service, end
user must deliver the URC equipment, freight prepaid, in its original
packaging or packaging affording adequate protection to URC at 420
Columbus Avenue, Valhalla, NY 10595. It is end user's responsibility
to backup any macro programming, artwork, software or other
materials that may have been programmed into the unit. It is likely
that such data, software, or other materials will be lost during service
and URC will not be responsible for any such damage or loss. A
dated purchase receipt, bill of sale, installation contract or other
verifiable proof of purchase is required. For the URC equipment
support and other important information, please visit URC's website
available at www.universalremote.com or call the Customer Service
Center at (914) 835-4484.
This limited warranty only covers the URC equipment issues caused
by defects in material or workmanship during ordinary consumer
use. It does not cover product issues caused by any other reason,
including but not limited to product issues due to commercial use,
acts of God, third-party installation, misuse, limitations of technology,
or modification of or to any part of the URC equipment. This limited
warranty does not cover the URC equipment sold as used, as is,
refurbished, so called "B stock" or consumables (such as batteries).
This limited warranty is invalid if the factory applied serial number
has been altered or removed from the URC equipment. This limited
warranty specifically excludes the URC equipment sold by
unauthorized resellers.
Page 9
MRX-2 NETWORK BASE STATION
With the exception of URC's IR-only, broad-based consumer remotes,
none of URC's PC programmable remotes or any of our Total
Control® whole-house equipment are authorized for online internet
sales. Buying URC's PC programmable remotes or any of our Total
Control® whole-house equipment online means buying equipment
that does not have URC's limited warranty. Such equipment is not
eligible for URC tech support or software support, either.
2. URC'S LIMITATIONS OF LIABILITY
IN NO EVENT SHALL URC BE LIABLE FOR INDIRECT, SPECIAL,
INCIDENTAL, EXEMPLARY, PUNITIVE OR CONSEQUENTIAL
DAMAGES OF ANY KIND OR LOSS OF PROFITS OR BUSINESS
OPPORTUNITY, EVEN IF URC IS ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
IN NO EVENT SHALL URC BE LIABLE FOR LOSS OF OR DAMAGE
TO DATA, COMPUTER SYSTEMS OR COMPUTER PROGRAMS.
URC'S LIABILITY, IF ANY, FOR DIRECT DAMAGES OF ANY FORM
SHALL BE LIMITED TO ACTUAL DAMAGES, NOT IN EXCESS OF
AMOUNTS PAID BY END USER FOR THE URC EQUIPMENT.
IN NO EVENT SHALL URC BE LIABLE FOR ANY EVENTS BEYOND
ITS CONTROL, INCLUDING ANY INSTANCE OF FORCE MAJEURE.
IN NO EVENT SHALL URC BE LIABLE FOR THE ACTS OR
OMISSIONS OF END USER OR ANY THIRD PARTY.
THE LIMITATIONS OF LIABILITY MAY NOT APPLY TO END USER
IN WHOLE OR IN PART, WHERE SUCH ARE RESTRICTED LIMITED
OR EXCLUDED BY APPLICABLE LAW AND SUCH SHALL APPLY
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW.
URC SHALL NOT BE HELD RESPONSIBLE FOR THE STATEMENTS
MADE BY OTHERS.
SOME STATES OR JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO END USER.
THIS LIMITED WARRANTY GIVES END USER SPECIFIC LEGAL
RIGHTS AND END USER MAY HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE OR JURISDICTION TO
JURISDICTION.
End User Agreement
The terms and conditions of the End User Agreement available at
www.universalremote.com/eua.php shall apply.
Page 10
MRX-2 NETWORK BASE STATION
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one more of the following measures:
u Reorient or relocate the receiving antenna.
u Increase the separation between the equipment and receiver.
u Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
u Consult the dealer or an experienced radio/TV technician for
help.
Warning!
Changes or modifications not expressly approved by the manufacturer could
void the user's authority to operate the equipment.
Note : The manufacturer is not responsible for any Radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user's authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
Page 11
MRX-2 NETWORK BASE STATION
Declaration of Conformity
Company Name
:
OH SUNG ELECTRONICS CO., LTD.
Company Address
:
#181 GONG DAN-DONG, GUMI, GYEONG BUK,
REPUBLIC OF KOREA
Phone: +82-54-468-7281, Fax: +82-54-461-8368
Contact Information
:
Brand Name
:
UNIVERSAL remote control
Product Name
:
Network Base Station
Model Name
:
MRX-2
This product herewith complies with the requirements of EMC Directive (2004/108/EC)
issued by the Commission of the European Community
Compliance with these directives implies conformity to the following European Community
n EMC Directive
l
EN 55022
l
EN 55024
l
EN 61000-3-2
l
EN 61000-3-3
List of test reports and/or certificate verified compliance with the standards above
n EMC Directive
l
Report No.
l
Testi ng Labora tory
: Gumi College EMC Center
Date of issue
:
Name and signature of authorized person
:
Page 12
January 30, 2013
James Novak
Senior Product Manager
Universal Remote Control Inc.
NOTE
Page 13
NOTE
Page 14
NOTE
Page 15
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: (914) 835-4484 Fax: (914) 835-4532
www.universalremote.com
OCE-0076D Rev 03_RH
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising