Clarity | D702HS | User guide | Clarity D702HS 30dB Expandable Handset for Clarity® D700 Series Phones User guide

Clarity D702HS 30dB Expandable Handset for Clarity® D700 Series Phones User guide
D704HS™
D702HS™
User Guide
Expandable Handset for Clarity®
Cordless Phones
D702HS is compatible with:
• D702
• D712
• D722
D704HS is compatible with:
• D704
• D714
• D724
Clarity, a Division of Plantronics, Inc.
6131 Preservation Drive,
Chattanooga,TN 37416
Tel: 800-426-3738 Fax: 800-325-8871
E-mail: claritycs@plantronics.com
Website: www.clarityproducts.com
©2011 Clarity, a Division of Plantronics, Inc.All rights reserved.
Clarity, D702HS, D704HS are trademarks or registered
trademarks of Plantronics, Inc.
Rev.C (12-15)
PRINTED IN CHINA
IMPORTANT SAFETY INSTRUCTIONS
Privacy of communications may not be ensured when using this phone.
Warning: To maintain the compliance with the FCC’s RF exposure guideline,
place the base unit at least 20 cm from nearby persons.
Warning: To reduce the risk of fire or injury to persons, read and follow these
instructions.
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the telephone.
3. Avoid contact with liquids. Do not locate base unit or handset near water,
for example, near a bathtub, wash basin, sink or laundry tub, in a wet
basement or near a swimming pool.
4. Avoid using a telephone (other than a cordless type) during a storm. There
may be a remote risk of electrical shock from lightning.
5. Do not use the telephone to report a gas leak in the vicinity of the leak.
6. Unplug this telephone from the wall outlets before cleaning. Do not use
liquid cleaners or aerosol cleaners on the telephone. Use a damp cloth for
cleaning.
7. Place this telephone on a stable surface. Serious damage and/or injury may
result if the telephone falls.
8. Do not cover the slots and openings on this telephone. This telephone
should never be placed near or over a radiator or heat register. This
telephone should not be placed in a built-in installation unless proper
ventilation is provided.
9. Operate this telephone using the electrical voltage as stated on the base unit
or the owner’s manual. If you are not sure of the voltage in your home,
consult your dealer or local power company.
10. Do not allow anything to rest on the power cord or locate this product in
an area where the power cord is likely to be damaged by furniture or foot
traffic.
11. Do not overload wall outlets or extension cords as this can increase the
risk of fire or electrical shock.
12. Never push any objects through the slots in the telephone. They can touch
dangerous voltage points or short out parts that could result in a risk of
fire or electrical shock. Never spill liquid of any kind on the telephone.
4
1
2
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
13. To reduce the risk of electrical shock, do not take this phone apart. Opening
or removing covers may expose you to dangerous voltages or other
risks. Incorrect reassembly can cause electric shock when the appliance is
subsequently used.
14. Unplug this product from the wall outlet and refer servicing to the
manufacturer under the following conditions: when the power supply
cord or plug is frayed or damaged; if liquid has been spilled into the
product; if the telephone has been exposed to rain or water; if the
telephone has been dropped or the case has been damaged; if the
telephone exhibits a distinct change in performance; if the telephone does
not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions. Improper
adjustment may require extensive work by a qualified technician to restore
the telephone to normal operation; if the telephone does not operate
normally by following the operating instructions.
15. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your local power company.
16. Do not attempt to open the AC adapter. There are potentially dangerous
voltages inside, and there are no serviceable parts.
17. Discontinue use of product and contact Clarity if the product overheats,
has a damaged cord or plug, if the product has been dropped or damaged
or if the product has come into contact with liquids.
18. Use only the AC adapter provided with this product or a replacement AC
adapter provided by Clarity.
19. This phone amplifies sound to loud volumes. To prevent hearing damage, all
users of the phone should be informed of the high volume capability of
the phone and children should only use the phone when supervised by an
adult.
20. Exposure to high volume sound levels or excessive sound pressure may
cause temporary or permanent damage to your hearing. Although there
is no single volume setting that is appropriate for everyone, you should
always use your telephone with the volume set at moderate levels and
avoid prolonged exposure to high volume sound levels. The louder the
volume, the less time is required before your hearing could be affected. If
you experience hearing discomfort, you should have your hearing checked
by a doctor. To protect your hearing, you should:
• Set the volume control in a low position and gradually increase the volume as needed. Before pressing the BOOST button, reduce
the volume to the lowest level. Use the phone on the lowest volume
setting as possible.
• Limit the amount of time you use the telephone at high volume evels.
21. If you experience a skin irritation after using this product, discontinue use
and contact Clarity.
BATTERY SAFETY INSTRUCTIONS
Dispose of used batteries according to the instructions.
1. Do not dispose of the battery in a fire as it may explode. Check with local
codes for possible special disposal instructions.
2. Do not open or mutilate the battery. Released electrolyte is corrosive and
may cause damage to the eyes and skin. It may be toxic if swallowed.
3. Exercise care in handling batteries in order not to short the battery
with conducting materials such as rings, bracelets and keys. The battery or
conduction material may overheat and cause burns.
4. Remove batteries when they are discharged and when the equipment will not
be used for an extended period of time. Dispose of batteries according to local
environmental laws.
5. Do not disassemble, heat, crush, deform or puncture batteries.
6. Do not attempt to charge non-rechargeable batteries.
7. Keep batteries out of the reach of children.
3
PACKAGING CONTENTS/LOCATION
The package contains the following items:
• 1 Handset
• 1 Charger base with attached power adapter
• 1 Belt clip
• 2 Rechargeable batteries
• 1 User guide
INSTALLING YOUR HANDSET
Connecting the charger base station
1) Locate the charger base; note that the power adapter is
permanently connected to your charger base.
2) Plug the end of power supply into the wall socket, as shown.
Your package includes all the items as shown here. If there is anything missing,
please contact our Customer Care Department immediately.
NOTE: PLEASE RETAIN A COPY OF PROOF OF PURCHASE FOR YOUR
RECORDS.
Location
For maximum coverage and reduce the interference, here are some guidelines
you should consider when you place the base unit:
- place it at a convenient, high,and central location with no obstructions
between the handset and base unit in an indoor environment.
- place it away from electronic appliances such as televisions, microwave ovens,
radios, personal computers, wireless devices or other cordless phones.
- avoid facing radio frequency transmitters, such as external antennas of mobile
phone cell stations.
- avoid plugging it into the same circuit as other major household electrical
appliances because of the potential for interference. Try moving the appliance
or the base unit to another power outlet.
If the reception for a base unit location is not satisfactory, move it to another
location for better reception.
Depending on the surrounding conditions as well as spatial and structural
factors, the range may be reduced. The range indoors is normally less than
outdoors.
4
LineCord
5
INSTALLING/CHARGING BATTERIES
1)
2)
3)
4)
Slide out the battery compartment cover.
Place the two batteries as indicated. Follow the polarity.
Slide the battery compartment cover back.
Put the handset on the base and charge for 16 hours first
time. A beep indicates that the handset is properly placed on
the base or charger.
Use only NiMH rechargeable batteries.
NOTE: Please refer to the Battery Safety Instructions on page 6 for
proper use and disposal of the batteries.
HOW TO REGISTER YOUR HANDSET
Your telephone (sold separately) can support up to five cordless
handsets. The additional handset(s) needs to register with the
telephone base before use.You must register each additional handset
separately.
The handsets provided within your main unit (sold separately) are
already registered as HANDSET 1 and so forth. Additional handsets
are assigned numbers in the order they are registered (HANDSET 2
to HANDSET 5).
When first purchased, all expansion handsets alternately display
• Press FIND on base 4 sec
and
• Then press # on handset.
The new handset should be charged without interruption for at least
30 minutes before registering to the telephone base.
How to add (register) your handset to the main unit
(sold separately)
NOTE: You must be in close proximity of your main unit's base in
order to register the handset; please move to where you can access
the FIND button on your main base (sold separately).
1. In idle mode, press <MENU/SELECT>, then <UP/DOWN> to
select Registration.
2. Press <MENU/SELECT> and screen will alternately show
• Press FIND on base 4 sec
and
6
7
HOW TO REGISTER YOUR HANDSET
• Then press # on handset
3. Press and hold FIND on the telephone base for about four
seconds.
4. Press # (pound key) on the handset. The screen shows
Registering...Please wait.
When the handset is registered successfully, HANDSET
registered and then HANDSET X appears on the screen, with X
being the handset number (1-5).
If the registration is not successful, the handset screen shows
Registration failed. Please start again from step 1 above.
Note: You cannot register a handset if any other system handset is in
use. To register an expansion handset, follow from the step 3 as above.
HOW TO DEREGISTER YOUR HANDSET(S)
Deregister all handsets
You can deregister handsets.You may need to deregister your handsets
if:
You have five registered handsets and need to replace a handset.
-ORYou wish to change the designated handset number of your
registered handsets.
You must first deregister ALL the handsets, and then register each
handset you wish to use again, one at a time.
If the base of your main unit is represented by either of the drawings
below, follow the directions below the drawings:
1. Press and hold FIND on the telephone base for about 24
seconds; release FIND.
2. Immediately press FIND again.
3. When complete, the handset screen alternately shows
• Press FIND on base 4 sec
and
8
9
HOW TO DEREGISTER YOUR HANDSET(S)
• Then press # on handset.
4. To register the handset(s) to the telephone base again, follow
the registration instructions in section Register a handset.
NOTE: There are no visual or audible alerts to indicate
the base is under deregistration mode.
If the base of your main unit is represented by the drawing below,
follow the directions below the drawing:
HOW TO DEREGISTER YOUR HANDSET(S)
Note:
•
If the deregistration process is not successful, you might need to
reset the system and try again. To reset, unplug the power from
the telephone base and plug it back in.
•
You cannot deregister the handset(s) if any system handset is in
use.
Note:
•
If your handset is registered to a base, you can re-register it to
a different base without deregistering it from the original base.
Just follow the directions in the section How to add (register) your
handset to the main unit (sold separately).
1. Press and hold FIND on the telephone base for about 10
seconds, until the SPEAKER light starts flashing; release FIND.
2. Immediately press FIND again; you will hear two quick beep
tones.
3. When complete, the handset screen alternately shows
• Press FIND on base 4 sec
and
• Then press # on handset.
4. To register the handset(s) to the telephone base again, follow
the registration instructions in section Register a handset.
10
11
FOR ADDITIONAL INFORMATION...
...Please refer to the user guide included with the main unit (sold
separately). Once registered, your additional handset will perform the
same functions as your existing main handset.
To identify the model number of your additional handset:
• Turn the charger base of your unit upside down; locate the
colored round label on your base.
• Orange label: D704HS™, up to 40dB of gain
• Compatible with:
• D704;
• D714;
• D724.
• Green label: D702HS™, up to 30dB of gain.
• Compatible with:
• D702;
• D712;
• D722.
Thank you...
new system.
If you have any questions regarding the operation of this telephone, please contact
one of our Customer Service Representatives for prompt and useful information.
TECHNICAL INFORMATION
• D702HS™ - 30dB
• D704HS™ - 40dB
Dimensions
• Handset Size: 7” x2 1/4” x 1 1/2” (H x W x D)
• Base Size: 2” x 3 3/4” x 3 1/2” (H x W x D)
Weight
• Handset Weight: 6.125 oz. (with batteries)
• Base Weight: 2.75 oz.
Power Requirements:
• AC Adapter (attached to base):
Input: 100V - 120V
Output: 6V DC 450 mA
• Battery: 2 X AAA, 600mAh Ni-MH
Use only NiMH rechargeable batteries.
NOTE: DO NOT MIX BATTERIES; REPLACE BOTH
BATTERIES WHEN NEEDED.
Phone: 800-426-3738
Fax: 800-325-8871
Email: claritycs@plantronics.com
Website: www.clarityproducts.com
12
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising