Valor | 1700KN/KP | Installation manual | Valor 1700KN/KP Installation Manual

Valor 1700KN/KP Installation Manual
Installation Manual
L2
Direct Vent Zero Clearance
Gas Fireplace
natural gas 1700KN
propane gas 1700KP
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings
exactly could result in serious
injury, death, or property damage.
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
▪
Do not try to light any appliance.
▪
Do not touch any electrical switch; do
not use any phone in your building.
▪
Leave the building immediately.
▪
Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
▪
If you cannot reach your gas supplier,
call the fire department.
Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
DANGER
Hot glass
will cause burns.
Do not touch glass
until cooled.
Never allow children
to touch glass.
4008056-01
©2019, Miles Industries Ltd.
A barrier designed to reduce
the risk of burns from the hot
viewing glass is provided with this
appliance and must be installed for
the protection of children and
other at-risk individuals.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where
not prohibited by local codes. This
appliance is only for use with the type
of gas indicated on the rating plate.
This appliance is not convertible for
use with other gases, unless a certified
kit is used.
INSTALLER: Leave this manual with the
appliance.
CONSUMER: Retain this manual for
future reference.
Massachusetts:
This manual contains instructions to
install the ENGINE ONLY. A trim kit is
REQUIRED to complete the installation.
A barrier screen is provided with the
trim kit. Refer to the manual supplied
with the trim for installation.
This appliance is a domestic roomheating appliance. It must not be used
for any other purposes such as drying
clothes, etc.
This appliance is suitable for
installation in a bedroom or bed
sitting room.
Ce guide est disponible en français sur demande.
The piping and final gas connection must be
performed by a licensed plumber or gas fitter
in the State of Massachusetts. Also, see Carbon
Monoxide Detector requirements in the fireplace
installation manual.
WARNING
This product can expose you to chemicals
including Benzene, which is known to the State
of California to cause cancer and birth defects or
other reproductive harm. For more information
go to www.P65Warnings.ca.gov.
Note: Natural gas, in its original state, contains
Benzene.
Valor Fireplaces
190–2255 Dollarton Highway
North Vancouver, BC, Canada V7H 3B1
T 604.984.3496 F 604.984.0246
valorfireplaces.com
2
The information contained in this manual is believed
to be correct at the time of printing. Miles Industries
Ltd. reserves the right to change or modify any
information or specifications without notice. Miles
Industries Ltd. grants no warranty, implied or stated,
for the installation or maintenance of your heater,
and assumes no responsibility for any consequential
damage(s).
© Copyright Miles Industries Ltd., 2019. All rights reserved.
Designed and manufactured for Miles Industries Ltd.
Welcome to Valor®
This appliance has been professionally installed by:
Dealer Name: ________________________________
Phone:______________________________________
Fireplace Safety ................................................. 4
Specifications ..................................................... 6
Kits & Accessories.............................................. 7
Dimensions & Location..................................... 8
Installation Planning ......................................... 9
Before Installing ............................................................9
Overview ......................................................................10
Mantel Clearances ......................................................11
Framing.........................................................................13
Wall Finish ....................................................................16
Material Specifications ..............................................16
Non-Combustible Cement Board ............................16
Avoiding Cracking Wall Finishes ...............................18
Venting .............................................................. 19
Overview ......................................................................19
Co-Axial ....................................................................... 20
Typical Co-axial Venting Components ....................20
Venting Chart ..............................................................21
Restrictor Settings .....................................................22
Horizontal Vent Termination ....................................23
Vertical Vent Termination .........................................24
Co-Linear Conversion ................................................ 25
Installation into existing fireplace cavity................25
Installation partially into fireplace cavity ...............26
Installation into existing adjacent chimney ...........27
Example of co-linear conversion accessories........28
Please read this manual BEFORE
installing and operating this
appliance.
HeatShift™ System—if used .................................... 33
Install HeatShift Take-Off Collars to Appliance .....33
Remove Convection Baffle .......................................33
Electrical Wiring ......................................................... 34
Gas Supply................................................................... 36
Liners ........................................................................... 38
Fuel Beds ..................................................................... 40
Driftwood Kit 1705DWK ........................................... 40
Decorative Glass Murano 1700DGM.......................43
Rocks & Shale Set 1714RSS ...................................... 44
Split Wood Kit 1700SWK ............................................47
Birch Log Kit 1700BLK ................................................50
Window Re-Installation & Checking ....................... 53
Wall Switch .................................................................. 54
Remote Control Pairing............................................. 56
Checking Operation and Aeration .......................... 58
Trim & Barrier Screen ................................................ 59
Wiring Diagram ................................................ 60
Approved Venting Components .................... 61
Commonwealth of Massachusetts ............... 63
Appendix A—Lighting Instructions............... 65
Appendix B—Remote Control Operation .... 66
Appendix C—Wall Switch Operation ............ 73
Appendix D—HeatShift™System .................. 74
Appendix E—Spare Parts ............................... 94
Installation ....................................................... 29
Appliance Preparation .............................................. 29
Unpack Appliance ......................................................29
Fit Standoffs ................................................................29
Remove Heat Shield ...................................................29
Convert from Top to Rear Outlet (if required) .......30
Fit Appliance into Framing ........................................31
Remove Window ........................................................32
3
Fireplace Safety
This manual contains very important information about the safe installation and operation of the fireplace. Read and
understand all instructions carefully before installing and operating the fireplace. Failure to follow these instructions
may result in possible fire hazard and will void the warranty.
Replacement manuals are available by contacting the Valor Customer Service at 1-800-468-2567, or by visiting
valorfireplaces.com.
WARNING: Extremely Hot!
Heat and flammability
• Some parts of the fireplace are extremely hot, particularly the glass windows. Use the barrier screens
provided or a gate to reduce the risk of severe burns.
• The glass windows can exceed 500°F (260°C) at full
capacity.
• Always keep the appliance clear and free from combustible materials, gasoline, and other flammable
vapors and liquids.
• Be aware of hot wall surfaces! The walls directly above
the fireplace can get very hot when the fireplace
heats. Although safe, it may reach temperatures in excess of 200ºF (93°C) depending on choice of optional
accessories. Do not touch!
• Be aware of hot hearth/floor surfaces! Any projections
directly around the fireplace can get very hot when
the fireplace heats. Although safe, they may reach
temperatures in excess of 200ºF (93°C)depending on
elevation of hearth. Be careful of touching these! Temperature of projection surfaces will be reduced when
barrier screens are installed.
• Some materials or items, although safe, may discolor,
shrink, warp, crack, peel, and so on because of the
heat produced by the fireplace. Avoid placing candles,
paintings, photos and other combustible objects
sensitive to heat or furniture within 36 inches (0.9 m)
around the fireplace.
• Due to its high temperatures, the appliance should be
located out of traffic areas and away from furniture
and draperies.
)LUHSODFH
Hearth
Do not put
furniture or other objects
in this space in front of
WKHȴUHSODFH
36” [0.9 m]
• Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to operating the appliance.
• Children and adults should be alerted to the hazards
of high surface temperature and should stay away to
avoid burns or clothing ignition.
• Young children should be carefully supervised when
they are in the same room as the appliance. Toddlers,
young children, and others may be susceptible to
accidental contact burns. A physical barrier is recommended if there are at-risk individuals in the house. To
restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children, and
other at-risk individuals out of the room and away
from hot surfaces.
• A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and shall be installed for the protection of children
and other at-risk individuals.
• Clothing or flammable material should not be placed
on or near the appliance.
4
Fireplace Safety
Glass windows
WARNING
Do not operate this appliance with the
glass front removed, cracked, or broken.
Replacement of the glass front should
be performed by a licensed or qualified
service person. Do not strike or slam the
glass front.
• The glass front assemblies must be in place and
sealed before the unit can be placed into safe
operation.
• The glass front assemblies must only be replaced as
complete units, as supplied by the fireplace manufacturer. No substitute material may be used.
• Do not use abrasive cleaners on the glass front assemblies. Do not attempt to clean the glass when
it is hot.
Venting
• This unit must be used with a vent system as described in this manual. No other vent system or components may be used.
• Never obstruct the flow of combustion and ventilation
air. Keep the front of the appliance clear of all obstacles and materials for servicing and proper operation.
• This gas fireplace and vent assembly must be vented
directly to the outside and must never be attached to
a chimney serving a separate solid fuel burning appliance. Each gas appliance must use a separate vent
system. Common vent systems are prohibited.
Intended use
• This appliance is designed and approved as a supplemental heater and provides the potential for most
energy conservation when used while attended. The
use of an alternate primary heat source is advisable.
• This unit is not for use with solid fuel.
• Do not use this heater as a temporary source of heat
during construction.
Installation and Servicing
• Installation and repair should be done by a qualified
service person. The appliance should be inspected
before use and at least annually by a professional
service person. More frequent cleaning might be
required due to excessive lint from carpeting, bedding
material, et cetera. It is imperative that control compartments, burners, and circulating air passageways
of the appliance be kept clean.
WARNING
Ceiling outlet
Side outlets
Front outlet
HeatShift
System:
Do not cover
or place items
in front of or
above outlet(s)!
5
Specifications
Approval & Codes
Supply Gas
This appliance is certified to ANSI Z21.88-2017/CSA
2.33-2017 American National Standard / CSA Standard
for Vented Gas Fireplace Heaters for use in Canada
and USA, and to CGA 2.17-91 High Altitude Standard in
Canada. This appliance is for direct vent installations.
Heater engine 1700KN uses
natural gas.
Heater engine 1700KP uses
propane gas.
This appliance complies with CSA P.4.1-15 Testing
method for measuring annual fireplace efficiencies.
The installation must conform to local codes or, in
the absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 or the Natural Gas
and Propane Installation Code CAN/CGA-B149.1. Only
qualified licensed or trained personnel should install
this appliance.
This appliance must be electrically grounded in
accordance with local codes, or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70
or the Canadian Electrical Code, CSA C22.1.
Gas
Altitude (Ft.)*
1700KN
1700KN
Natural
Propane
0-4,500 feet*
Input Maximum (Btu/h)
36,000
36,000
Input Minimum (Btu/h)
21,000
22,500
Manifold Pressure (in w.c.)
4”
10”
Minimum Supply Pressure (in
w.c.)
5”
11”
Maximum Supply Pressure (in
w.c.)
10”
14”
Main Burner Injector Marking
DMS#32
DMS#49
51
30
220
160
Pilot Injector Marking
Min. Rate By-Pass Screw
*High Altitude Installations
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to 4,500
feet (1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the current
ANSI Z223.1 and/or local codes having jurisdiction.
Heating value of gas in some areas is reduced to
compensate for elevation—consult your local gas
utility to confirm.
For installations at elevations above 4,500 feet
(1,370 m) in Canada, please consult provincial and/or
local authorities having jurisdiction.
6
The supply pressure must be
between the limits shown in the Ratings section.
The supply connection is 3/8” NPT male and located on
the left hand side of the firebox. A shut-off valve (not
supplied) is required on the supply line to isolate the
unit during service. See Gas Supply Installation section
for details.
Conversion Kits
The 1700K are supplied as natural gas or propane
gas and are field convertible between fuels. See
instructions packaged with the conversion kits for
further information.
Electrical
Ratings
Model
X
The 1700K are designed to run on battery power and
do not require an electrical power source to operate
as a heater. However, they require electrical power
to operate optional 1595CFKV2 Circulating Fan Kit,
GV60WIFI WiFi Kit or 1270RBK Remote Blower Kit.
HeatShift™System
The 1700K are designed to allow the installation of the
optional HeatShift System, a convection system that
redistributes the warm air flow away from the fireplace
opening to a more desirable location using natural
convection, without use of a fan.
The warm air flow may be relocated to a position higher
up the wall, out the sidewalls, or even to another room.
The result is much cooler wall temperatures above the
fireplace opening for locating televisions, artwork, etc.
Please note that the framing and mantel clearances
are affected by the installation of the HeatShift
System. Refer to “Appendix D—HeatShift™System™” on
page 74 for more information.
Outdoor Conversion Kit
The 1700K models are supplied standard for indoor
applications and may be adapted for installation in
specific “outdoor” applications protected from weather
as defined in the GV60CKO outdoor conversion kit
manual.
Kits & Accessories
Required Kits Information accurate at the time of printing and subject to change
without notice.
Fuel Beds (choose one)
1705DWK
Driftwood Kit
1700DGM
Decorative Glass Murano Kit
1714RSS
Rock & Shale Kit
1700SWK
Split Wood Kit
1700BLK
Birch Logs Kit
Liners Panels (choose one)
1715FBL
Fluted Black Liners
1725RGL
Reflective Glass Liners (requires 1725RGL-3 Glass Retainer Kit)
1735LML
Limestone Liner Set
1740SSL
Stacked Stone Liners
Trims (choose one)
Barrier Screen
1730CIK
Clean Install Kit - Fine Mesh - REQUIRES HeatShift
4007675
1750v2
Linear 3-1/2” Surrounds
4004221
1775LFB
Linear 1” Finishing Trim Black
4005562
Optional Accessories Information accurate at the time of printing and subject to change
without notice.
Gas Conversion Kits
1700KNGK
Conversion to natural gas
1700KPGK
Conversion to propane gas
Other Accessories
GV60WIFI
WiFi kits - REQUIRES GV60 V-module
GV60CKO
Outdoor Fireplace Conversion Kit
1506DRK
Additional rocks for Driftwood Kit
1595CFKV2
Circulating Fan Kit - REQUIRES GV60 V-module
1270RBK
Remote Blower Kit
LDK
HeatShift System Kits (gravity flow) - MANDATORY with 1730CIK
Hearth Gate
Hearth gates such as Cardinal’s VersaGate are available at retail stores carrying
safety products for children.
WARNING
HeatShift System MUST be installed on
this appliance when using 1730CIK—Clean
Installation Kit!
WARNING
Optional electrical accessories ARE NOT
ALLOWED when adapting appliance for
outdoor use.
7
Dimensions & Location
Dimensions
57-3/4” [ 1467 mm]
52” [ 1321 mm]
HeatShift System
outlets (remove plates)
15-1/16”
[383 mm]
18”
[457 mm]
19-7/8”
[505 mm]
Center
Line
Li
Top View
Heat shield
required for
rear vent
outlet
applications
18-1/2”
[470 mm]
15-1/16”
[383 mm]
6-5/8” dia.
Venting
ȴHOG
convertible
from top to
rear outlet
Zero Clearance
6WDQG2΍V
Header
33-1/8” [841 mm]
9-3/8””
[238 mm]
3-3/4”
[95 mm]
Gas Line
Access Point
Left Side View
49-11/16” [ 1262 mm]
Electrical
El
t i l
Inlet Point
Front View
Right Side View
Zero Clearance
Zero Clearance
WR6WDQGR΍V
DWEDFNFRUQHUV
DW%DFNDQG6LGHV
Location
20-1/2”
[519 mm]
Zero Clearance
DWEDFNFRUQHUV
Face of
Framing
88
”[
22
35
m
m
]
Corner Dimensions
8
1270RBK Remote
Blower Kit outlet
(remove plate)
62-1/4” [ 1581 mm]
1270RBK Remote
Blower Kit outlet
(remove plate)
14-1/2
2”
[369 mm]
Min. 43” [ 1092 mm]
to underside of header
4”
[102 mm]
Min. 44-1/2” [ 1130 mm]
to top of cement board
32-3/8” [822 mm]
Center of vent
Installation Planning
Before Installing
Caution
Only qualified, licensed, or trained personnel
should install this appliance.
1. YOU NEED TO KNOW FROM THE HOMEOWNER:
•
Will optional HeatShift System* be used;
•
Height of appliance and shelf, if used;
•
Thickness and type of wall finish around
appliance;
•
Trim used*;
•
Other optional accessories used (if any);
•
Venting configuration.
2. Unpack the appliance, removing all items packed
inside and around it. Recycle the packaging.
3. Check that you have everything, using the Pack Content sheet. Also, check that you have:
•
Fuel bed (packed separately);
•
Liner panels (packed separately);
•
Remote Battery and Wall Switch Kit;
•
HeatShift System components (if used);
•
Gas conversion kit (if necessary);
•
Venting accessories;
•
Electrical accessories (if used).
4. Carefully read the Installer’s Checklist included with
the fireplace for the installation sequence.
WARNING
*HeatShift System MUST be installed on
this appliance when using 1730CIK—Clean
Installation Kit!
9
Installation Planning
Overview
Note: This appliance may be installed in outdoor, weather protected environments as defined in the GV60CKO
Outdoor Conversion Kit instruction manual.
Mantel—See Mantel & Hearth Clearances
Framing—See Framing Requirements
1/2 inch thick non-combustible cement board –NOT supplied
Surround
d Pllate
with Barrier Screen
(required)
Supplied as vertical outlet, field convertible to horizontal
outlet. Note - Vertical rise required in vent system
Optional HeatShift System
outlets (4)—Required with
1730CIK
Narrrow 1” Trim 1775LFB and
wide
er 3-1/2” steel Trim 1750
adjuss table, accept additional
non--combustible finish over
cement board and
behind trim.
1730CIK’s narrow trim
requires HeatShift.
Cement board finishes up to
perimeter of trim.
Note: 1730CIK installs before
cement bo
b ard.
1700K heater
Remote
Handset
Wall Holder
Electrical
junction box
(not supplied) to
connect power
when using
optional fan, WiFi
Wall
ll Fiiniish
h
Any wall finishes applied
over cement board must
be non-combustible.
Com
mbustible mantel are ok
provided they conform to
chart on p
pag
g page
ge
g 11.
Combustible Floor
Hearth: not required.
If used, must be minimum 4”
below fireplace opening unless
using HeatShift (see “Appendix D—
HeatShift™System” on page 74)
WARNING
Some materials or items, although safe,
may discolor, shrink, warp, crack, peel,
and so on because of the heat produced
by the fireplace. Avoid placing candles,
paintings, photos, and other items
sensitive to heat around the fireplace.
10
Remote Battery
and Wall Switch Kit
(required) (35-foot wire
length) (supplied)
Combustible Framing Allowed Beneath Fireplace. When the appliance
is installed directly on carpeting, tile or other combustible material
other than wood flooring, the appliance shall be installed on a metal
or wood panel extending the full width and recessed depth of the
appliance.
WARNING
HOT WALL SURFACES! The wall directly
above the fireplace is constructed of noncombustible materials and, although safe,
it may reach temperatures in excess of
200°F (93°C) depending on choice of trims.
Do not touch. Finish wall using materials
suitable for these temperatures.
Installation Planning
Mantel Clearances
Combustible Mantel—Left Side View
NOTE
Ceiling
Use for the optional HeatShift
System affects mantel and hearth
clearances. See HeatShift section in
Appendix D of this manual.
Mantel Projection
HeatShift System MUST be installed
on this appliance when using
1730CIK—Clean Installation Kit!
0 2” 4” 6” 8” 10”12”
44”
42”
40”
38”
Face of 1/2” thick
non-combustible
cement board
Fireplace
Opening
Mantel
Height
(from
Bottom
of Unit)
24” Min. to Ceiling
WARNING
(from Face of Cement Board)
23-7/8”
Do not put
furniture or objects
within 36” (914 mm)
of front of appliance
4” minimum to
combustible or
non-combustible hearth
9-3/8”
Bottom of Unit
11
Installation Planning
Mantel Clearances
Combustible Sidewall / Mantel Leg—Top View
FIREPLACE
Face of
Finished
Wall
Fireplace Opening
49-11/16”
Wall
Min. 4” to
wall or
combustible
mantel leg
12
Installation Planning
Framing
Framing Dimensions
NOTE
Use fo the optional HeatShift
System affects mantel and hearth
clearances. See HeatShift section in
Appendix D of this manual.
WARNING
HeatShift System MUST be installed
on this appliance when using
1730CIK—Clean Installation Kit!
NOTE: Height of cavity may be
D΍HFWHGE\YHQWFRQȴJXUDWLRQ
- see page 15
1/2” thick non-combustible
cement board required above,
on each side and below
engine opening (NOT supplied)
NOTE: This unit requires a
solid platform to support it.
Combustible framing allowed
EHQHDWKȴUHSODFH:KHQWKH
appliance is installed directly
on carpeting, tile or other
combustible material other
WKDQZRRGȵRRULQJWKH
appliance shall be installed
on a metal or wood panel
H[WHQGLQJWKHIXOOZLGWK
and recessed depth of the
appliance
Between underside
of header and bottom
RIȴUHER[
43”
20”
57-3/4”
No hearth required.
If using a hearth,
see page 11.
13
Installation Planning
Framing
Framing with Partial Shelf—Top Outlet
ȋWKLFN
non-combustible
Cement Board
9-3/8”
[238 mm]
Fireplace
Opening
14-1/2”
[369 mm]
Min. 1”
[25 mm]
clearance to
combustibles
around
vertical
vent pipe
43” [ 1093 mm] to underside of combustible cavity
19-1/4”
[489 mm]
15-1/16”
[383 mm]
Approx. 10-3/4”
[274 mm]
from back
surface of
ZDOOȴQLVKWR
front surface
of appliance
case w/no
YHQWR΍VHW
PARTIAL SHELF, top outlet
14
Installation Planning
Framing
Venting Considerations—Vertical Takeoff
*Notes—ALL venting considerations
• Dimensions of venting are based on using Dura-Vent elbows. Elbow curve radius
dimensions will vary when using other
brands. In general, other brands have
slightly bigger radius.
• Minimum 24 inches vertical pipe section
required right at unit. Refer to venting chart
on page 30 for allowable horizontal runs.
43” [ 1093 mm] to underside of combustible cavity
19-1/4”
[489 mm]
14-1/2”
[369 mm]
Fireplace Left Side View
9-3/8”
[238 mm]
Min 1”
[25 mm]
Required
clearance
to vertical
pipe is
within
stand-off
space
Stand-off
37” [940 mm]
*67-1/2” [ 1715 mm] with 24” vent pipe
24” pipe section
• 3 inches clearance to combustibles required above horizontal pipe. Slope horizontal pipe upwards 1/4 inch per foot. 1
inch clearance required around sides and
bottom of horizontal pipe and around vertical pipe.
• When calculating effective pipe lengths
subtract approximately 1-1/2 inch for pipe
joint - for example, a 12 inches pipe section will add approximately 10-1/2 inches
overall.
Venting Considerations—Horizontal Takeoff
Fireplace Left side view
43” [ 1093 mm] to underside of combustible cavity
19-1/4”
[489 mm]
2-1/2”
[64 mm]
9-3/8”
[238 mm]
14-1/2”
[369 mm]
36-1/2” [927 mm]
*70” [ 1778 mm] with 24” vent pipe
24” pipe section
15
Installation Planning
Wall Finish
Material Specifications
Non-Combustible Cement Board
Non-Combustible
The L2 Linear fireplace requires a 1/2” (13 mm) thick
non-combustible cement board to be used as a wall
surface immediately surrounding the unit’s opening—
see diagram for minimum coverage.
Material which will not ignite and burn. Such materials
are those consisting entirely of steel, iron, brick, tile,
concrete, slate, glass or plasters, or any combination
thereof.
Extending the cement board well beyond the minimum
shown will help avoid cracking due to differential
expansion of materials.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750°C shall be considered
non-combustible materials.
Pre-drill cement board with oversized holes and do
not over-tighten screws to avoid cracking due to heat
expansion.
Combustible
Materials made of or surfaced with wood, compressed
paper, plant fibers, plastics, or other material that
can ignite and burn, whether flame proofed or not,
or plastered or unplastered shall be considered
combustible materials.
Standard gypsum wall board may be used beyond the
perimeter of the cement board.
Minimal coverage area of non-combustible cement board.
Any wall ȴQLVKDSSOLHGWRVKDGHGDUHDPXVWEHQRQFRPEXVWLEOH
NON-COMBUSTIBLE MATERIALS ONLY
READ INSTRUCTIONS
MATÉRIAUX INCOMBUSTIBLES SEULEMENT
CONSULTEZ LE GUIDE D’INSTALLATION
Min. 60” [1524 mm]
E
D
Non-combustible
cement board
required thickness:
1/2” [13 mm]
Min. 44-1/2” [1130 mm]
A
NON-COMBUSTIBLE MATERIALS ONLY
NON-COMBUSTIBLE MATERIALS ONLY
READ INSTRUCTIONS
READ INSTRUCTIONS
MATÉRIAUX INCOMBUSTIBLES
SEULEMENT
MATÉRIAUX
INCOMBUSTIBLES SEULEMENT
CONSULTEZ LE
GUIDE D’INSTALLATION
CONSULTEZ LE GUIDE D’INSTALLATION
Linear 1700 outline
LQFOXGLQJVWDQGR΍V
B
Joints preferred at corners
to prevent cracking
C
Flush with bottom of unit;
add extra cement board
to overlap framing.
With 1750 or
1775 trims
with 1730CIK kit
A
Min. 20-1/2 [521]
Min. 20-1/8 [511]
B
14-3/4 [375]
15-13/16 [401]
C
Min. 9-1/4 [235]
Min. 8-9/16 [218]
D
Min. 5 [127]
Min. 4-1/2 [114]
E
Min. 50 [1270]
Min. 51-1/16 [1296]
inches [mm]
16
D
Installation Planning
Non-Combustible Finishing Over Cement
Board
Additional non-combustible material such as tile, etc.,
may be applied over top of the cement board or you
may choose to leave it finished clean with no tile, etc.
Wall Finish
Wider trim (1750)
can adjust up to 1”
forward of surface of
cement board.
Cement board tucks
behind trim.
Be aware that a trim is always required. Finish should
not cover the trims.
(2 1/4
35 ”
m
m
)
Po
(inssib
th le s
e d cre
es w
ign lo
atec
d
1775 and 1750 Trims
Only the 1775 and 1750 style trims will accept tile, etc.
tucked behind them (up to 5/8” thick for the 1775 and
up to 1 inch thick for the 1750).
1730 Trim
1730 trim must be installed BEFORE cement board.
Cement board and finishes are applied to the perimeter
of the trim frame. Cement board and finished CANNOT
be tucked under this trim.
Narrow trim (1775)
can adjust up to 5/8”
forward of surface of
cement board.
Cement board tucks
behind trim.
of ard f
h l
ov eat ush
erl er; wi
ap ad th
p i n d bo
g f extr
ram a
ing
Clean Installation
Kit 1730CIK requires
HeatShift. Cement
board finishes up to
perimeter of frame.
Must install
BEFORE cement
board.
17
Installation Planning
Avoiding Cracking Wall Finishes
We recommend installing the optional HeatShift
System to reduce the wall temperatures and minimize
the possibility of cracking wall finishes.
WARNING
HeatShift System MUST be installed on
this appliance when using 1730CIK—Clean
Installation Kit.
Wall Finish
• Always pre-drill screw holes through cement board
and use screws specific for material used.
• Always use mesh tape over joints.
• Always stagger joints in wall board.
• Behind joints, double up studs or use studs “on the
flat” to add extra support to the joint. Adhesive on
the backside of wall board behind any joints can help
control differential movement.
• Use multiple, thinner coats of joint compound and allow to dry thoroughly between coats.
• Ensure framing materials are dry.
If a clean finish with no tile, etc. is desired, joints in the
cement board and the transition to gypsum board
will require special attention if future cracking is to be
controlled. Be aware that temperatures on the noncombustible wall surface above the appliance can
exceed 200°F (93°C).
• After finishing the wall, introduce heat gradually to
slowly dry any excess moisture rather than drying too
fast.
Below are some tips on how to best avoid any cracking:
• Avoid using lage one-piece slab of material with a
cut-out in the middle as a surround for the fireplace.
Expansion above the opening will cause cracking at inside corners. Provide a joint that intersects the inside
corner to avoid cracking.
• Allow materials to dry thoroughly before finishing the
wall. Cement board has the ability to absorb up to 30
percent of its weight in water and may shrink as much
as 1/8” over a 48” length when drying from a saturated condition. Running the fireplace for an extended
period before final finishing will help drive out moisture.
• Avoid notching cement board or tiles around corners
of window opening and instead provide a joint that
intersects the corner.
Provide joints
either here or
here
Cracks
18
Venting
Overview
Top or Rear Outlet
Framing Vent in Combustible Walls & Ceilings
This unit is supplied with a top vent outlet which can
be field-converted to a rear vent outlet. See Appliance
Preparation section for more information.
When penetrating through combustible walls and
ceilings, frame a minimum of 10 in x 10 in opening and
ensure that the insulation is kept clear of the vent pipe
using either a wall thimble or an attic insulation shield.
Follow the installation instructions supplied with the
individual venting components.
Vent Material
This unit is approved for installation using
4 x 6-5/8 inches co-axial direct vent pipe and
accessories as listed in the Approved Venting Components
section on pages 61–62 of this manual. Follow the
installation instructions supplied with the individual
venting accessories.
This unit may also be converted to co-linear (1 x 3 in by
1 x 4 in) venting for use in solid-fuel burning fireplaces
and chimneys using adapters and accessories—see list
in the Approved Venting Components section on pages
61–62 of this manual.
Align the vent center
to the center of the
frame
10” (254 mm)
Vent Sealing
Seal all outer coaxial pipe and elbow joints, including
sectioned elbow joints, using high quality, high temperature 2 inch wide self-adhesive aluminum foil tape
(Nashua-322-2 brand or similar). Wrap the tape completely around all joints and press firmly to seal.
A high temperature black silicone sealant may be used
in the outer joints as a substitute to foil tape.
Ensure all the pipe joints have a minimum of 1 ¼ inch
overlap.
Tape all joints
(including all
elbow joints)
10” (254 mm)
Important Installer Notice – Weather
Sealing & Vapor Barriers
It is the installer’s responsibility to ensure that vent
installations through exterior walls are caulked and
weatherproofed in such a manner as to:
• Prevent rain water from entering the wall from the
weather side by adequately caulking the outer vent
plate to the exterior wall surface.
• Prevent moisture inside the home from penetrating into the wall structure by ensuring the inside
wall plate is adequately sealed to the inside vapor
barrier.
• Prevent rain water and moisture from entering the
walls by sealing the joints between the outer vent
tube and the inner and outer wall plates.
Wall Thickness
The appliance vent is suitable for penetrating a
combustible wall assembly up to 8 inches in thickness.
A non-combustible wall can be of any thickness up to
the maximum horizontal run of vent pipe allowed for
the particular installation.
We recommend the use of a high quality
polyurethane sealant.
All horizontal pipe runs must be graded 1/4 inch per
foot upwards in the direction of the exhaust flow. The
final pipe length, when terminating through the wall
may be graded downwards slightly to prevent water
migration.
19
Venting
Co-Axial
Typical Co-axial Venting Components
2-PIECE
WALL THIMBLE
90˚ ELBOW
HORIZONTAL
TERMINATION
PIPE
LENGTH
VERTICAL
TERMINATION
STORM
COLLAR
PIPE
LENGTH
FLASHING
90˚ ELBOW
ATTIC
INSULATION
SHIELD
HORIZONTAL
TERMINATION
ATTIC
FIRESTOP
CEILING
FIRESTOP
Rear Outlet
PIPE LENGTH
2-PIECE
WALL THIMBLE
PIPE
LENGTH
90˚ ELBOW
PIPE
LENGTH
Top Outlet
20
PIPE
LENGTH
Top Outlet
Venting
Co-Axial
How to Read the Venting Chart
be used. Excludes the 45 degrees take-off elbow
shipped with the appliance.
The chart below applies to co-axial roof or wall
termination.
1.
6. Each 90 degrees elbow installed on the horizontal
plane is equivalent to a 3 feet horizontal pipe;
therefore, 3 feet must be subtracted from allowable
horizontal run. (45 degrees elbow is equivalent to
18 inches horizontal pipe.)
A minimum vertical rise of 24 inches is required
directly off the unit or after first elbow, as shown.
2. The total length of the vent pipe cannot exceed
40 feet.
7.
3. The minimum vertical height with roof termination
is 6 feet.
4. Any combination of rise and run can be used as
long as they are within the allowable limits shown
on the chart below.
All horizontal pipe runs must be graded 1/4 inch per
foot upwards in the direction of the exhaust flow.
The final pipe length, when terminating through the
wall may be graded downwards slightly to prevent
water migration.
8. A restrictor adjustment is required for most
installations having a vertical rise—see “Restrictor
Settings” on page 22.
Note: The restrictor is shipped installed at the
exhaust exit of the firebox.
5. A maximum of 4 x 90 degrees elbows—or
equivalent (2 x 45 degrees = 90 degrees)—can
Venting Chart
Allowable Co-Axial
Vent Configurations with
restrictor positions
4 x 90º ELBOWS MAXIMUM
(or equivalent)
V3
3” min.
above top of
horizontal pipe
1” min.
all around
vertical pipe
40
38
36
H1
NO INSTALLATION
34
1” min. around
bottom & sides
of horizontal pipe
Position #5
32
30
V2
28
VERTICAL RISE (ft)
26
Minimum 24”
pipe section
V1
Example 1
V Value = V1 (2’) + V2 (4’) + V3 (1’)= 7’
H Value = H1 (2’) = 2’
Restrictor position # 1 required
Position #4
24
22
20
18
Positions #2/3
16
14
12
Example 1
10
Position #1
8
6
4
45° elbow take-off
supplied with unit
24” minimum
vertical pipe rise
off unit or after
first elbow
NO INSTALLATION
2
0
0
2
4
6
8
10
12
14
16
18
20
HORIZONTAL RUN (ft)
21
Venting
Co-Axial
Restrictor Settings
The restrictor is located in the roof of the firebox
hidden above the top liner panel. Adjust the restrictor
before installation of the top liner panel. Should
subsequent adjustment be required, you will need to
remove the top liner panel—see “Liners” on page 38.
Inside firebox—roof venting port
ALL INSTALLATIONS REQUIRE A RESTRICTOR for
improved flame picture and performance. This unit is
supplied with a pre-fitted restrictor having five different
positions or settings. The restrictor is shipped mounted
at the maximum open position which is used for rear
venting with no vertical rise. The level of restriction
required depends on the vertical rise in the venting
system and, to a lesser degree, the horizontal run and
number of elbows.
The amount of restriction is based on laboratory tests.
The ideal restrictor position may vary slightly, especially
when the vent pipe length is near the limits of the
acceptable configurations for each type of restrictor.
The chart on the previous page shows
the vent restrictor required relative to the
length of the vent pipe.
To set the restrictor position:
1. Establish the required position of the
restrictor looking up the venting table
on the previous page.
2. Release the screws (2) on each side of
the restrictor already installed on the
firebox roof port.
Position #1
Position #2
Position #3
Position #4
3. Slide the restrictor in the required position.
4. Tighten the screws.
Position #5
22
Venting
Co-Axial
Horizontal
Horizontal Vent
VentTermination
Termination Location
•
•
•
The vent terminal must be located on an outside
wall or through the roof.
This direct vent appliance is designed to operate
when an undisturbed airȵow hits the outside vent
terminal from any direction.
The minimum clearances from this terminal that
must be maintained when located on an outside
wall are shown in ȴgure below. Any reduction in
these clearances could result in a disruption of the
airȵow or a safety hazard. Local codes or regulations
may require greater clearances.
•
The vent terminal must not be recessed into a wall
or siding.
•
The vent terminal should be positioned where any
snowdrifts will not cover it.
•
Sidewall vent terminations require a terminal guard
such as 658TG or 845TG when accessible—within 7’
of ground.
Min. 72”
V
Max. 72”
G
A
Alcove detail
(open on one
side) Normal
ceiling/soɝt
clearances
apply.
KEY
VENT TERMINAL LOCATIONS - MINIMUM DISTANCES
MINIMUM
CLEARANCE
Inches
Cm
A
Clearance above grade, verandah, porch, deck or balcony
12
30
B
Clearance to window or door that may be opened
12
30
C
Clearance to permanently closed window (recommended to prevent condensation on window)
12
30
D
Vertical clearance to ventilated soɝt located above the terminal within a horizontal distance of 2 feet (60 cm)
from the center-line of the terminal
18
46
E
Clearance to unventilated soɝt
12
30
F
Clearance to outside corner
12
30
G
Clearance to inside corner
12
30
H
Horizontal clearance to center-line of meter/regulator assembly located within 15 feet (4.6bm) below the
terminal
36
90
I
Clearance to service regulator vent outlet
36
90
J
Clearance to non-mechanical air supply inlet to the building or the combustion air inlet to any other appliance
12
30
K
Clearance to a mechanical air supply inlet
72
180
84
210
12
30
Clearance above paved sidewalk or a paved driveway located on public property
L
M
Note:
Note: A vent must not terminate directly above a sidewalk or paved driveway, which is located between two singlefamily dwellings and serves both dwellings. THIS DOES NOT APPLY to direct vent, non-consdensing appliances in
the Province of Ontario.
Clearance under a verandah, porch, deck or balcony
Only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the ȵoor
Local codes and regulations may require di΍erent clearances.
23
Venting
Co-Axial
Vertical Vent Termination
Roof Pitch
Minimum
"H" (feet)
Flat to 7/12
1'
Over 7/12 to
8/12
1.5'
Over 8/12 to
9/12
2’
Over 9/12 to
10/12
2.5’
Over 10/12 to
11/12
3.25’
Over 11/12 to
12/12
4’
Over 12/12 to
14/12
5’
24
Horizontal
overhang
Termination
cap
Vertical
wall
Min.
18”
Overhang should not
extend beyond vent if
within 48” of
termination cap
Min. 24”
(unvented soffit)
Min. 36”
(vented soffit)
Storm
collar
‘H’
Roof
flashing
Venting
Co-Linear Conversion
Installation into existing fireplace cavity
Approved 3 x 4 co-linear
termination
Note: Co-linear portion of vent system may only be
installed within a solid-fuel burning fireplace and
chimney.
The appliance must not be connected to a chimney flue
serving a separate solid-fuel burning appliance.
3” intake
liner
4” exhaust
liner
Flashing
Co-linear
adapter
Requires the Valor Co-Axial to Co-Linear appliance
Adapter 1156CLA, two lengths of 2-ply flexible chimney
liner both approved for venting gas appliances: one 3”
diameter liner for intake and one 4” diameter liner for
exhaust, a 3 x 4 co-linear termination kit and flashing.
Firebox zero clearance standoffs supplied with the heater
may be removed to suit this application.
3” min. bend radius
for intake liner and
4” min. bend radius
for exhaust liner
1156CLA Co-Linear Vent Adapter
FRONT
REAR
11-11/16”
9-3/8”
3” exhaust
collar
Any finishes
applied
around the
fireplace
must be noncombustible
1 x 3”
intake
liner
and
1 x 4”
exhaust
liner
1156
Co-linear
adapter
Engine
Co-Linear installation into existing fireplace
4”
4” exhaust
collar adapter
1-1/2”
Dimensions with 1156CLA Co-Linear Adapter
8-5/8”
Rules for Co-Linear Venting
52”
• Maximum 40 feet vertical pipe
• Minimum 10 feet vertical
• Maximum offset 8 feet with liners at minimum
45 degrees from horizontal plane
3” intake
4” exhaust collar
on the centerline
• Restrictor: Not required when using co-linear venting.
Installation
32-3/8”
For installation of the adapter to the appliance, see the
instructions supplied with the 1156CLA.
Note: Co-linear flexible aluminum venting should be
professionally inspected periodically for corrosion
and damage and replaced when necessary. If the
installation does not allow for future inspection or
replacement of the flexible aluminum venting, then
stainless steel vent liners should be used.
18-1/8”
25
Venting
Co-Linear Conversion
Installation partially into fireplace cavity
Note: Co-linear portion of vent system may only be
installed within a solid-fuel burning fireplace and
chimney.
The appliance can be adapted to co-linear applications
using an existing chimney. The appliance must not be
connected to a chimney flue serving a separate solidfuel burning appliance.
Requires the Valor Co-Axial to Co-Linear appliance
Adapter 1156CLA, 46DVA-GLC34 or equivalent, two
lengths of 2-ply flexible chimney liner both approved
for venting gas appliances: one 3” diameter liner for
intake and one 4” diameter liner for exhaust, a 3 x 4 colinear termination kit and flashing.
3” intake
liner
Approved 3 x 4
co-linear termination
4” exhaust
liner
Flashing
Co-linear
adapter
3” min. bend radius
for intake liner and
4” min. bend radius
for exhaust liner
Clearances
to combustible
materials listed
elsewhere in this
manual apply
Framed
wall
The appliance must be fully enclosed while maintaining
clearances to combustibles detailed elsewhere in this
manual.
Rules for Co-Linear Venting
1156
Co-linear
adapter
• Maximum 40 feet vertical pipe
• Minimum 10 feet vertical
• Maximum offset 8 feet with liners at minimum
45 degrees from horizontal plane
• Restrictor: Not required when using co-linear venting.
Note: Co-linear flexible aluminum venting should be
professionally inspected periodically for corrosion
and damage and replaced when necessary. If the
installation does not allow for future inspection or
replacement of the flexible aluminum venting, then
stainless steel vent liners should be used.
26
Engine
1 x 3”
intake
liner
and
1 x 4”
exhaust
liner
Co-Linear installation partially into existing fireplace
Venting
Co-Linear Conversion
Installation into existing adjacent chimney
Note: Co-linear portion of vent system may only be
installed within a solid-fuel burning fireplace and
chimney.
The appliance can be adapted to co-linear applications
using an existing chimney. The appliance must not be
connected to a chimney flue serving a separate solidfuel burning appliance.
Requires the Co-Axial to Co-Linear appliance Adapter
46DVA-34CLAA or equivalent, two lengths of 2-ply
flexible chimney liner both approved for venting gas
appliances: one 3” diameter liner for intake and one 4”
diameter liner for exhaust, a 3 x 4 co-linear termination
kit and flashing.
The appliance must be fully enclosed while maintaining
clearances to combustibles detailed elsewhere in this
manual.
Approved 3 x 4
co-linear termination
4” exhaust
liner
3” intake
liner
• Maximum 40 feet vertical pipe
• Minimum 10 feet vertical
• Maximum offset 8 feet with liners at minimum
45 degrees from horizontal plane
• Restrictor: Not required when using co-linear venting.
Note: Co-linear flexible aluminum venting should be
professionally inspected periodically for corrosion
and damage and replaced when necessary. If the
installation does not allow for future inspection or
replacement of the flexible aluminum venting, then
stainless steel vent liners should be used.
Approved 3 x 4
co-linear termination
4” exhaust
liner
3” intake
liner
Flashing
Flashing
3” min. bend radius
for intake liner and
4” min. bend radius
for exhaust liner
3” min. bend radius
for intake liner and
4” min. bend radius
for exhaust liner
Clearances
to combustible
materials listed
elsewhere in this
manual apply
Rules for Co-Linear Venting
46DVA-34CLAA
or 46DVA-GCL34
Co-linear
Framed
adapter
wall
46DVA-GCL34
or 46DVA-34CLAA
Co-linear
adapter
Clearances
to combustible
materials listed
elsewhere in this
manual apply
Framed
wall
Max. 12”
1 x 3”
intake
liner
and
1 x 4”
exhaust
liner
Engine
Installation using 46DVA-34CLAA
1 x 3” intake liner
and
1 x 4” exhaust liner
Engine
Installation using 46DVA-GCL34
27
Venting
Co-Linear Conversion
Example of co-linear conversion accessories
Examples of Co-axial to Co-linear Appliance Adapters
46DVA-GCL34
46DVA-34CLAA
Examples of Co-linear Terminal Configurations
10”
10”
7-5/8” dia.
collar
3” Inlet & Exhaust
Collars . A 3” - 4”
adapter may be used
for exhaust liner.
Co-Linear Terminal (typical)
Co-linear Termination Kits
Alternate Co-linear to Co-axial Conversion at Terminal
Co-Linear to CoAxial Adapter
With...
Co-axial Terminal Cap
28
Flashing
Flashing Kit
Installation
Appliance Preparation
Unpack Appliance
Beware of sharp edges! Wear gloves!
1. Remove the cardboard wrapping and the wood pallet from the appliance and discard.
2. Unpack any loose items from around the appliance.
3. Remove the window and set aside in a safe place
to avoid damage—see”Remove Window” on page
32.
4. Verify that you have all the components required for the installation, including:
•
approved cement board;
•
liners and fuel bed (in separate cartons);
•
trim kit with barrier screen;
•
venting components and accessories;
•
optional HeatShift system if used;
•
electrical components if installing optional
decorative light wall switch or blower.
Fit Standoffs
The standoffs are supplied flat on the firebox sides
and fixed at one end. Swivel up the flat standoffs, bend
them as shown and fix the loose end to the top of the
firebox.
Standoff
Standoffs installed
Fold flat
standoffs
Remove Heat Shield
Remove the heat shield from the top of the appliance
case (3 screws). If using a rear outlet, keep the shield
to reinstall after converting the top to rear outlet—see
next subsection. If using the top outlet or the HeatShift
system, discard the shield.
Remove heat shield (3 screws)
29
Installation
Appliance Preparation
Convert from Top to Rear Outlet (if required)
This unit is supplied with a top vent outlet which can
be field-converted to a rear vent outlet.
Please note that the rear outlet requires the installation of the heat shield on top of the heater case as
indicated.
1. Remove the top outlet collar (6 screws).
2. Swivel the collar and install as a rear outlet (6 screws).
3. Reinstall the heat shield to the top of the appliance
case (3 screws).
Remove top outlet (6 screws)
Reinstall heat shield
to top of appliance
(3 screws)
Swivel the outlet so that it
is oriented towards the rear
and reinstall to heater
(6 screws)
Rear outlet with required heat shield
30
Installation
Appliance Preparation
Fit Appliance into Framing
1. Remove the 4 screws retaining the engine to its pallet.
2. Taking great care not to cut your hands on the sheet
metal edges, lift the appliance out of its packing
base and place it in the framing. Make sure that
the unit is at the right height with consideration to the
height of the hearth or combustible flooring.
3. Fold out four mounting tabs and recess the appliance in the framing as shown.
4. Fasten the unit to framing using 4 screws or nails at
the mounting tabs.
Note: The sheet metal front face of the appliance is
flush with the framing studs.
front face of
appliance
flush
mounting
tabs (4)
Appliance flush to framing
31
Installation
Appliance Preparation
Remove Window
The window is held in place by a spring-loaded lever on
each side.
1. To remove the window, locate the levers on each
side of the window towards the top. Using your finger, pull the lever towards you and unhook it from
the window frame bracket.
Window frame
2. Gently pull the top of the window outward.
3. Lift the window out of its bottom railing and set it
aside in a safe place to avoid damage.
Section Views
32
Bottom railing
Installation
HeatShift™ System—if used
Install HeatShift Take-Off Collars to Appliance
Remove Convection Baffle
1. Remove the four cover plates on top of the appliance case (6 screws each).
To be effective, the HeatShift system requires that an
internal convection baffle located above the firebox
inside the appliance case be removed to allow the hot
air flow to convect upwards into ducts installed on the
fireplace.
Remove the convection baffle from the appliance. It is
held in place by 3 screws located right behind the upper
edge of the fireplace opening. Recycle this panel as it is
no longer needed.
Appliance front panel—shown transparent for clarity
Co
n
ve c
t io
nb
affl
e
2. Install the take-off collars on the holes on top of the
appliance’s case (6 screws each).
Remove convection baffle
See “Appendix D—HeatShift™System” on page 74 for
more details regarding the installation.
WARNING
All FOUR (4) takeoffs MUST BE
CONNECTED TO PLENUM(S).
WARNING
The Linear fireplaces requires the
removal of the internal convection baffle
for the HeatShift system to function
properly—read instructions carefully!
33
Installation
Electrical Wiring
Install Electrical Wiring (if required)
This section provides information to install the electric pre-wiring required for use with the optional
1595CFKV2 Circulating Fan Kit and/or the GV60WIFI Kit.
2. Provide a steel surface mount electrical utility
box (Iberville BC 1110 or equivalent), thread cable
through knock-out in the back of box and through
the cable clamp locking ring (if used).
All wiring must be done by a qualified electrician in
accordance with local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70 or
the Canadian Electrical Code, CSA C22.1.
Electrical Requirements
1595CFKV2—120 V, 60 Hz, less than 1 amp
GV60WIFI kits—120 V, 60 Hz, less than 1 amp
General Requirements
Optional 1595CFKV2 and WiFi module are powered by a
V-module (sold separately) which plugs into a grounded
receptacle installed within the fireplace enclosure by a
qualified electrician.
Notes
3. Strip wire and terminate grounded receptacle.
• Fan speed control provided through remote handset.
• Receptacle and box must be located as per these
instructions. Wiring within this box must have a minimum 90°C temperature rating.
Installation
1. Thread the cable through the cable clamp and
through the hole in the lower right hand corner of
the fireplace casing. Do not tighten the clamp yet..
Fireplace
casing
Stud
Pull just enough cable
out front for now to make
termination easier
34
4. Mount the electrical box to the side of the fireplace
casing using self-tapping sheet metal screws. Pull
the excess cable back through the cable clamp and
tighten the locking ring to the cable clamp. Alternate
clamp without locking ring may be used - ensure the
proper clamp is used for the type of cable used.
Installation
Electrical Wiring
5. Tighten cable clamp on outside of fireplace casing
and secure and excess wire to framing.
6. Mount receptacle into electrical box.
7. Mount steel cover to electrical box and plug in the
accessory cable.
35
Installation
Gas Supply
Set-up Gas Supply
Pressure test the supply line for leaks.
The gas supply inlet
connection is a 3/8” NPT male
connector located on the left
hand side of the firebox.
The appliance and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.5 kPa).
Gas line
access hole
2-1/2” (64 mm)
diam.
4
(10 ”
2m
m)
X
Front
of the
appliance
The appliance must be isolated from the gas supply
piping system by closing its individual manual shut-off
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than 1/2
psig (3.5 kPa).
Failure to either disconnect or isolate the appliance
during pressure testing may result in regulator or valve
damages and void the warranty. Consult your dealer in
case of damages.
3-3/4”
(95 mm)
Window
Left side view
Flexible
connector
supplied
with unit
The unit is supplied with a stainless steel flex line to
allow the appliance to be disconnected for service. An
individual shut-off valve (not supplied) is required on
the supply line ahead of the flex connector.
Use only new black iron or steel pipes or copper tubing
if acceptable—check local codes. Note that in USA,
copper tubing must be internally tinned for protection
against sulfur compounds.
Unions in gas lines should be of ground joint type.
The gas supply line must be sized and installed to
provide a supply of gas sufficient to meet the maximum
demand of the appliance without undue loss of
pressure.
Sealant used must be resistant to the action of all gas
constituents including LP gas. Sealant should be applied
lightly to male threads to ensure excess sealant does
not enter gas lines.
36
Receiver
Appliance front
outer casing
transparent for
clarity
Manifold Pressure
Adjustment behind
Plastic Cap
Valve Assembly
Control Valve
Installation
Gas Supply
Pressure Test Points
Valve Inlet
Pressure
The minimum supply pressure is given in the section
“Specifications” on page 6.
All piping and connections must be tested for leaks
after installation or servicing. All leaks must be
corrected immediately.
When testing for leaks:
Manifold
Test
Pressure
Manifold pressure
adjustment screw
located behind
plastic mushroom
cap.
• Make sure that the appliance is turned off.
• Open the manual shut-off valve.
• Test for leaks by applying a liquid detergent or soap
solution to all joints. Bubbles forming indicate a gas
leak.
Caution
Never use an open flame to check for leaks!
Correct any leak detected immediately.
The pressure test tapping locations are shown in
the figure at right. An internal regulator within the
valve controls the burner manifold pressure. The
correct pressure range is shown in the table in section
“Specifications” on page 6. The pressure check
should be made with the burner alight and at its
highest setting. See “Appendix A—Lighting Instructions”
on page 65 for full operating details.
Pressure Testing
37
Installation
The liners install in the manner outlined below with the
exception of the 1725RGL Reflective Glass Liners and
the 1740SSL Stacked Stones Liners—see instructions
supplied with the liners.
Liners
Place the panel’s right section on the ledge above
the ports of the rear of the firebox. The section sits
on the ledge behind the tabs, with its plain edge on
right side; slide it behind the right side panel.
Unpack the liner panels carefully.
1. Inside the firebox, on the top of each side, release
the screw of the side panel anchors (one per side)
just enough to allow them to rotate.
2. Place the right end panel against the right wall of the
firebox. Place the bottom edge in first and carefully
press the panel to the outside wall.
4. The top panel is supplied in two
identical sections. The top of the
panel is beveled and the ‘fire side’ is
straight at the front and notched at
the back. When installed, the panel
rests on the top of the rear and side
panels. In the front, it rests on the
top panel support bracket located
inside the front edge of the firebox.
Position and slide top panel into corner.
3. The rear panel is supplied in three sections which
are fitted into each other. Two of the sections are
identical. Their step edges go towards the middle to
fit into the middle section.
Top panel
support
bracket
5. Carefully position, lift and slide second section of
the top panel on top of the first.
Rear panel sections—top view
38
Installation
6. Place rear panel’s centre section on the ledge behind the tabs, slide it to the right so that its stepped
edge fits into the stepped edge of the rear panel’s
right section.
7. Place the left side panel against the left
wall of the firebox.
Liners
10. Carefully lift, slide and position top panel on to left
side and rear panel.
NOTE: If gapping occurs between each section of
the rear panel, a lift tab located on each end of
ledge can be bent by hand to close the gap.
8. Tighten the side panel anchors on each
side of the firebox
9. Place the remaining rear panel’s section behind
the left side panel and fit its stepped edge to the
stepped edge of the rear panel’s center section.
39
Installation
Driftwood Kit 1705DWK
Material required
• Black steel platform (supplied with appliance)
• Driftwood Kit containing:
•
6 logs
Fuel Beds
Installation
Carefully unpack the kit.
1. Install the steel platform around the burner as
indicated. The openings in the platform should be
underneath.
Installed platform
2. Carefully spread the vermiculite by hand on the
surface of burner, forming a single layer to the
approximate level of the top of the flange at the
edge of the burner. Do not pour too much to avoid
blocking the burner ports.
•
10 pebbles
NOTE: Ensure the area within the pilot shield is clear
of vermiculite.
•
1 bag of vermiculite
Pilot shield
40
Installation
Logs and rocks
Each log has pegs to help you locate them on the
platform. Install the logs as shown below.
Fuel Beds
4. Place the right rear log as indicated. Pivot tail end to
just cover small hole located in platform.
1. Place the rear log in the center of the firebox at the
rear. NOTE: There are two holes for the left peg of
this log.
Natural gas: Place the log’s left peg in the front hole.
Propane gas: Place the log’s left peg in the rear hole.
Propane
gas
Natural
gas
2. Place the rear left log as indicated.
5. Place right cross log as indicated. Pivot other end to
locate on the recess of right rear log as indicated,
ensure fimly located.
3. Place the front left log as indicated.
41
Installation
6. Place centre cross log to rear log as indicated. Pivot
tail end so tip is just inside fireplace window line.
Fuel Beds
IMPORTANT: Approved for use only with vermiculite
provided with your Valor fireplace. The use of any
other products may void your fireplace warranty.
WARNING
Choking Hazard! Ensure that the fireplace
area is clear of vermiculite particles as
these could be ingested by small children.
Vacuum area after installation.
7. Any extra vermiculite may be added outside the
burner on the front media platform if desired.
8. Place the rocks as shown below (do not place directly on the burner).
Long Beach Driftwood Kit installed
42
Installation
Fuel Beds
Decorative Glass Murano 1700DGM
Material required
• Steel platform (supplied with appliance)
• Decorative Glass Murano Glass kit, which contains:
•
1 bag of clear 1/2” fireglass
•
8-pieces glass platform
3. Carefully spread the fireglass by hand, on the surface of burner forming a single layer to the approximate level of the top edge of the flange around the
burner. Do not pour from the bag and do not pour
too much to avoid blocking the burner ports.
Installation
Carefully unpack the kit.
1. Install the steel platform around the burner as
indicated. The openings in the platform should be
underneath.
4. Some fireglass may be added on the platform to
cover the edge of the burner and in the space in
front and behind the pilot shield.
NOTE: Ensure the area within the pilot shield is clear
of fireglass.
Installed platform
2. Install the glass plates on the platform, textured side
underneath and smooth side on top. Follow the diagram below as the pieces are not all the same size.
pilot area
Pilot shield
narrower glass plates at the back
narrower
longer glass plates
in the middle
wider
wider glass plates at the front
Top view—glass plates
IMPORTANT: Approved for use only with the fireglass
provided with your Valor fireplace or the tempered
crushed fireglass brands American Fireglass™ or
firegear. The use of any other fireglass products may
void your fireplace warranty.
WARNING
Installed glass plates
Choking Hazard! Ensure that the fireplace
area is clear of fireglass particles as these
could be ingested by small children.
Vacuum area after installation.
43
Installation
Fuel Beds
Rocks & Shale Set 1714RSS
Installation
1.
Material required
• Black steel platform (supplied with appliance)
• Rock & Shale Set, which contains:
•
Install the steel platform around the burner as
indicated (no screws). The openings in the platform
should be underneath.
5 twigs
1
2
3
Installed platform
•
34 rocks (assorted colors)
2. Distribute the mixed shale by hand directly onto
the burner, forming a single layer. Do not pour
from the bag and do not pour too much to avoid
blocking the burner ports. Take care not to cover
the pilot light.
x 34
•
1/2lb-bag of 3/4” black shale
•
1/2lb-bag of 3/4” grey shale
3.
Carefully unpack the kit, as the logs are fragile.
44
Place one rock behind the pilot light shield.
Installation
Fuel Beds
4. Place the rest of the rocks evenly on the platform
around the burner.
7.
Place twig #3 as shown, over the center of the
burner. Use the bigger rocks to keep the twig off the
shale as much as possible.
3
1
5. Place the first twig #2 at the left hand end of the
burner. Use the bigger rocks to keep the twig off the
shale as much as possible. Be careful not to block
the pilot light.
8. Place the second twig #1 as shown. Use the bigger
rocks to keep the twig off the shale as much as
possible.
2
3
6. Place the first twig #1 as shown. Use the bigger
rocks to keep the twig off the shale as much as
possible.
2
1
9. Place the second twig #2 as shown. Use the bigger
rocks to keep the twig off the shale as much as
possible.
1
1
2
45
Installation
2
Fuel Beds
1
1714RSS—Rock and Shale Kit installed
IMPORTANT: Use only the ceramic rocks, twigs and
shale provided with your Valor fireplace The use of
any other types of rocks, twigs or shale may void your
fireplace warranty.
WARNING
Choking Hazard! Ensure that the fireplace
area is clear of shale pieces as these could
be ingested by small children. Vacuum
area after installation.
46
3
1
2
Installation
Fuel Beds
Split Wood Kit 1700SWK
Logs, embers & splinters
Material required
• Some logs are marked with a number to facilitate the
installation.
• Black steel platform (supplied with appliance)
• Split Wood Kit, which contains:
•
1 bag of splinters
•
1 bag of small embers
•
11 logs
Installation
Platform
Carefully unpack the kit.
Install the steel platform around the burner as
indicated. The openings in the platform should be
underneath.
• Some logs also have positioning pins underneath
which fit into the SQUARE holes in the platform.
Installed platform
• Some logs straddle the burner.
47
Installation
Fuel Beds
1. Install the logs according to the images below. Use
the following order: log 1, 2, 3, 4, 6, 5, 7, 9, 8, 10 and
11.
Notes
•
Log 1 overlaps slightly the pilot shield.
•
Log 2 rests on notch of log 1.
•
Log 3’s narrow end rests on the pilot shield.
•
Log 4 straddles the burner.
•
Log 6 straddles the burner.
1
3
5
2
Log 7 rests on front notch of log 6.
•
Log 9 straddles the burner.
•
Log 8 rests on the notch of log 9.
•
Log 10 rests on the rear right corner of the
burner.
•
Log 11 rests on notch of log 10.
10
9
5
2
6
4
3
8
7
10
9
48
•
7
1
7
Log 5 rests on rear notch of log 6.
8
6
4
•
11
11
Installation
2. Carefully spread the embers by hand, in a single
layer on the surface of burner between the logs.
Do not pile up the embers to avoid blocking the
burner ports.
Fuel Beds
NOTE: Ensure the area within the pilot shield is clear
of embers or splinters.
Pilot shield
3. Some embers may be added on the platform to
cover the edge of the burner and the round holes.
4. Spread some splinters to the embers.
Pilot shield
1700SWK—Split Wood Kit installed
IMPORTANT: Approved for use only with the ceramic
embers and splinters provided with your Valor fireplace. The use of any other products may void your
fireplace warranty.
WARNING
Choking Hazard! Ensure that the fireplace
area is clear of embers / splinters as
these could be ingested by small children.
Vacuum area after installation.
49
Installation
Birch Log Kit 1700BLK
Material required
• Black steel platform (supplied with appliance)
• Birch Log Kit, which contains:
•
Fuel Beds
Installation
1.
Install the steel platform around the burner as
indicated (no screws). The openings in the platform
should be underneath.
9 logs
Installed platform
2. Place log L2 with pin inserted in the hole as shown.
L2
•
1 bag of mixed grey embers (8 cup bag)
•
1 bag of splinters
Carefully unpack the kit, as the logs are fragile.
3. Place log L1 on top off L2 and across the burner to
the front platform.
L2
L1
50
Installation
Fuel Beds
4. Place log L12 to the right of L2 on the rear platform
and burner as shown.
7.
Place log L6 on top of L4 and onto the front platform.
L4
L2
L5
L12
L1
5. Place log L5 on the rear platform to the right of L12,
with the pin in the hole as shown.
L2
L6
L12
8. Place log L8 over the back right corner of the
burner, with the pin in the hole as shown.
L4
L12
L8
L5
6.
Place log L4 on top of L5 and across the burner to
the front platform.
9. Place log L3 on top of L8 and onto the front platform.
L5
L4
L8
L4
L12
L3
51
Installation
Fuel Beds
10. Place log L9 between L4 and L3, from the front
platform to the burner as shown.
L5
L4
L9
11. Place (do not pour) embers onto the burner, among
the logs. Place splinters on top to preference.
L8
L3
IMPORTANT: Approved for use only with the ceramic
embers and splinters provided with your Valor fireplace. The use of any other products may void your
fireplace warranty.
L1
L2
52
Choking Hazard! Ensure that the fireplace
area is clear of embers / splinters as
these could be ingested by small children.
Vacuum area after installation.
L5
L12
L6
1700BLK—Birch Log Kit installed
WARNING
L4
L8
L9
L3
Installation
Window Re-Installation & Checking
Refit and Check Window
1. Place the window in its bottom railing. Ensure to
remove any vermiculite or glass particles in the railing before installing the window.
Window frame
WARNING
The window unit must be correctly
installed, fastened and sealed after
servicing or serious bodily injury and/or
damage to the appliance may result.
To ensure a safe operation:
• Double-check that the bottom of the
window frame is correctly installed in the
bottom support railing;
• Verify that the levers are hooked properly
to the window tabs then;
Bottom railing
• Pull out the top of the window and release
it to insure the springs return it;
2. Push the top of
the window
frame against
the firebox.
Section Views
• Ensure the window is sealed before
operation.
WARNING
Failure to install the window correctly can:
• Leak carbon monoxide.
• Affect the performance of the fireplace.
• Damage components.
• Cause overheating resulting in dangerous
conditions.
3. While you hold it, pull and hook the side levers back
to the window brackets on each side.
Damage caused by incorrect window
installation is not covered by the Valor
Warranty.
6. If the Hot Glass Warning plate has been removed
from the front lower corner of the window, reinstall it by sliding it between the glass and the
frame as indicated.
4. Pull out top of window to ensure spring loaded
levers work properly.
5. Apply firm hand pressure around the window frame
to ensure the window is sealed tight against the
firebox.
Hot Glass Warning Plate
53
Installation
Wall Switch
Install Remote Battery and Wall Switch Kit
(required)
The Remote Battery and Wall Switch Kit is provided
with this appliance. It connects to the receiver in the
fireplace.
The receiver is located under the firebox, left of the
control valve. It is maintained in position with Velcro
bands.
4. Run harness assembly to mounted position of junction box, securing harness to framing using insulated staples (not included)
5. Feed harness assembly through a restrain on rear
of junction box, feeding through until harness
sheath is pinched by retainer and providing sufficent length to make connection to rear of switch
and battery holder.
1. Pull out the receiver from its location to connect the
battery holder and wall switch.
2. Feed the ‘white connector end’ of the harness assembly through side holes in fireplace liner body to
receiver. Ensure sufficient harness length to allow
for removal of receiver. Note - coil up any extra harness at fireplace end.
3. Connect switch to auxillary 5-pin junction and
power connection to jack.
IMPORTANT: The
connection can only
be done one way.
6. Secure junction box to the mounting surface using
appropriate fasteners (not included)
7. Align molex connection on switch cable of harness
assembly and connect to switch.
Do not force it or
damage the pins on
the receiver box!
Caution
DO NOT PUT BATTERIES IN THE BATTERY HOLDER
until the wires are connected to the burner
control unit as short-circuit could result in the
destruction of the electrical components.
Do not run the switch wire over the top of the
firebox. Route the wire so it does not contact the
firebox.
54
Installation
8. Mount switch plate to junction box with 2 long
screws provided. Note: switch position left or right
to suit homeowner wishes.
Wall Switch
11. Feed cable tie through the 2 side slots of battery
cover assembly.
12. Position battery holder to rear face and secure together with cable tie. note clearance is required for
battery snap connection.
Cable tie
Side slot
9. Locate and secure magnet plate using 2 ‘long’
screws provided
10. Place and secure cover plate to box using 4 screws
provided
Caution
DO NOT USE a screwdriver or other metallic
object to remove the batteries from the battery
holder or the handset! This could cause a short
circuit to the receiver.
Snap connector
Rear view
Front view
13. Make the snap connection, load 4 AA alkaline batteries into holder (included with fireplace) then feed
back into junction box assembly.
Note: Do not put batteries in the receiver, only in
the battery holder by the wall switch.
14. Test the operation of the wall switch—see ““Appendix C—Wall Switch Operation” on page 73.
To avoid short-circuit to the receiver, position the
antenna so that it DOES NOT TOUCH the ignition
wire.
55
Installation
Remote Control Pairing
Radio Frequency
918.0 MHz for USA and Canada.
This device complies with Part 15 of the FCC Rules
and with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference,
and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
Receiver behind front panel,
left of gas valve
Remote Control Initial Pairing
The receiver and the handset of the remote control
system must be initially paired before the first use.
(Note that batteries must already be installed in the
wall mounted battery holder)
1. Insert two 1.5 V AAA alkaline batteries in the handset.
Reset
button
Velcro
Battery
wall holder
connection
Appliance’s
front panel
2. Locate the Reset button on the front side of the
receiver.
3. With a thin object, press and hold the receiver’s
RESET button until you hear one short and one long
beeps. After the second beep, release the reset button.
4. Within the subsequent 20 seconds, press and hold
the button on the remote handset.
will be
displayed on the handset during the pairing sequence. You will hear two short beeps confirming
the pairing is done.
If you hear one long beep, the pairing sequence has
failed or the wiring is incorrect.
This is a one time pairing only and is not required when
changing the batteries of the handset or battery holder.
The remote control system is now ready to use.
56
RESET
Reset button
Installation
Remote Control Pairing
Install Remote Control Handset Wall Holder
The remote control kit for this fireplace comes complete
with a wall-mounted holder. This holder is not required
in all installations but is provided as an optional feature
for those customers who wish to mount the remote
handset to the wall.
To install the holder to the wall, find a convenient
location and use the hardware provided with the kit.
Cover the screws with the included caps to finish the
mounting.
Once mounted, the holder is magnetic - simply place
the remote gently into the holder.
IMPORTANT: The location of the remote control handset
is important to assure proper temperature regulation.
To obtain a constant temperature, we recommend that
the handset should be between 3 and 15 feet away
from the appliance but not directly above it. We also
advise that the handset should be located away from
any other heat source and not in direct sunlight as
this may affect the temperature sensor located in the
remote handset.
57
Installation
Checking Operation and Aeration
Checking Operation
Locating Aeration Control
Turn the fireplace flame up and down using the
remote control to confirm that the full range of
inputs is achieved—see the remote control operation
instructions in “Appendix B—Remote Control
Operation” on page 66.
Adjusting Aeration
Light the fire and allow the unit to warm up for 10–15
minutes to evaluate the flame picture. The burner is
equipped with an adjustable shutter to control primary
aeration. The shutter is factory-set to an aeration gap
which will give optimum performance for the vast
majority of installations.
Depending of the fuel bed used, altitude and other
considerations, the flame picture may be improved by
adjusting the aeration. The need for adjustment should
be determined only by operating the appliance with the
fuel bed, panels and window installed and evaluating
the flame picture after a 15-minute warm-up.
Increasing aeration will cause the flames to appear
more transparent and blue showing more ceramic
effects glow.
Aeration control lever
Open
Close
Decreasing aeration will cause the flames to appear
more yellow or orange showing less ceramic effects
glow.
Too little aeration may result in black carbon forming
on logs or roof panel and dropping into the firebox.
Top view—Air shutter lever located under the firebox
behind the front panel
58
Installation
Install trim plinth support
Install the trim plinth support hooking it vertically on
the stiffener bracket, as shown. The stiffener bracket is
located just behind the front panel below the window.
Trim & Barrier Screen
1730CIK—Clean Installation Kit
WARNING
HeatShift System MUST be installed on
this appliance when using 1730CIK—Clean
Installation Kit.
If you are installing the 1730CIK Clean Installation Kit,
you need to do it BEFORE the cement board.
Plinth
support
1. Break off tabs from each corner of the fireplace’s
front opening (8 tabs, 2 at each corner). Bend tabs
back and forth to break them, or cut them with tin
snips as indicated in the kit’s installation instructions.
Stiffener
bracket
Install Trim and Barrier Screen
Install the trim chosen by the customer for their
fireplace. Install as well the barrier screen which is
provided with the trim.
Show the customer how to remove the barrier screen
to access the controls.
Follow the instructions provided with the trim and
leave those instructions behind for the customer’s
further reference.
2. Remove the internal convection baffle inside the
appliance case, above the firebox. See “Appendix
D—HeatShift™System” on page 74
59
Wiring Diagram
GV60 Wiring Diagram
MAN Knob
Fan
(optional)
RBWSK
120V
Low voltage
FAN
V-Module
(optional)
black
red
Thermocouple
PILOT
Required for optional
fan or wifi kits
Interruptor
Block
8-Wire Cable (bundled)
POWER
Combination Control Valve
Connector
IGNITOR
AC
Power
Battery Holder
Main Valve Knob
yellow
Wifi
Module
red
Antenna
(optional)
PANEL
V-module
required
Receiver
Battery Power
Battery Holder
RESET Button
60
Approved Venting Components
—
—
TM-4RHT
—
—
—
Horizontal
BDM
Deluxe Co-axial
High Wind Co-axial
MILES
INDUSTRIES
TM-4HT
AMERIVENT
ICC EXCEL
DIRECT
4DT-HC
Standard Co-axial
RLH
INDUSTRIES
SELKIRK
46DVA-HC
Venting Parts Description
SECURE
VENT
DURA-VENT
Approved Direct Vent Suppliers for Valor Models 1700
Venting Parts Code / availability by Manufacturer
—
—
4DHC round
658DVK2
940160
—
—
4DHCS square
—
940160
SV4CHC
—
—
—
Standard Co-axial
46DVA-VC
4DT-VT
—
—
HSDV46581313
4DH-1313
—
46DVA-VCH
—
TM-4SVT
SV4CGV
—
—
—
Extended Co-axial
46DVA-VCE
—
—
—
—
—
—
HS-C33U-99
Co-linear
—
TM-IVT
Aluminum
Flexible
Liner
Vent
Adapters
HS-C33F-1313
Adjustable Pipe Length and
Pipe Extensions
4” x 6-5/8”
DV 45°
Elbows
—
559CLT
HCL-1313-33
940034B
940033HWS
940033RD
Snorkel, 14” Rise
46DVA-SNK14
4DT-ST14
TM-4ST14
—
—
4D14S
—
94040614
Snorkel, 36” Rise
46DVA-SNK36
4DT-ST36
TM-4ST36
—
—
4D36S
—
94040636
Co-axial-to-Co-linear
Adapter
46DVA-GCL34
46DVA-34CLAA
ADT-AAC
TM-4CAA
—
—
4DCAB33
1156CLA
940106433
Co-linear-to-Co-axial
Adapter
46DVA-CT
46DVA-34CLTA
ADT-CTB
TM-4CTA
—
—
4DCAT33
—
—
3” or 4” diameter
Galvanized or Black
Galvanized or Black
NOTE: 2-ply liner approved to CAN/ULC S635 suitable for venting gas appliances. As manufactured by Z-Flex,
Flexmasters or others.
TM-ALK33
952703
AF3-35L
TM-ALK43
2280 Series
—
—
—
—
AF4-35L
TM-ALT33
952704
TM-ALT34
46DVA-08A
46DVA-08AB
(3” to 7”)
4DT-ADJ(B)
46DVA-16A
46DVA-16AB
(3” to 14-1/2”)
ADT-AJ12
TC-4DLS1
ADT-AJ12B
TC-4DLS1B
(4” to 10”)
4DT-ADJ
—
—
—
4D7A or 4D7AB
(3” to 5”)
—
94610608
(4” to 8-1/2”)
—
4D12A or 4D12AB
(3” to 10”)
—
94610616
(4” to 16”)
SV4LA
SV4LBA
Galvanized or Black
ADT-TL14
TC-4DLS2 SV4LA12
46DVA-17TA
46DVA-17TAB ADT-TL14B TC-4DLS2B
(14” to 22”) (1-7/8” – 21”) SV4LBA12
(11” to 17”)
—
4D16A or 4D16AB
(3” to 14”)
—
—
Galvanized or Black
ADT-TL38 TC-4DLA30 SV4LA24
46DVA-24TA
46DVA-24TAB ADT-TL38B TC-4DLA30B
(38” to 70”) (16.5” – 29”) SV4LBA24
(17” to 24”)
—
4D26A or 4D26AB
(3” to 24”)
—
—
Coaxial Flex
46DVA-48FF
46DVA-120FF
—
—
—
—
—
—
—
Galvanized
46DVA-E45
—
TE-4DE45
—
4D45L
—
94620645
4D45LB
—
94620645B
—
—
—
4D90L
—
—
4D90LB
—
—
Black
46DVA-E45B
Galvanized Swivel
—
—
Galvanized
TE-4DE45B SV4EBR45
4DT-EL45
Black Swivel
DV 90°
Elbows
—
940033B
HCL-99-33
HCL-913-33
3PDVCV
940364
940206LP
High Wind Co-axial
46DVA-CL34
46DVA-CL34P
—
940264
—
Vertical
Termination Caps
4DVC
SV4E45
—
4DT-EL45(B)
46DVA-E90
—
—
SV4EB45
TE-4DE90
—
—
Black
46DAV-E90B
—
Galvanized Swivel
—
4DT-EL90
Black Swivel
—
4DT-EL90(B)
TE-4DE90B SV4EBR90
SV4E90
—
—
SV4EB90
—
94620690
—
—
94620690B
61
Approved Venting Components
4DT-06
TC-4DL6
SV4L6
46DVA-06B
4DT-06(B)
TC-4DL6B
SV4LB6
—
—
—
—
—
—
—
94610606
90410606B
Galvanized
7” long
4D7
—
Pipes 4” x 6 5/8” ( ID x OD )
Black
Galvanized
46DVA-09
4DT-09
TC-4DL9
Black
46DVA-09B
4DT-09(B)
TC-4DL9B
Galvanized
46DVA-12
4DT-12
TC-4DL1
Flashings
—
—
SV4L12
12” long
4D12
—
Black
46DVA-12B
4DT-12(B)
Galvanized
46DVA-18
4DT-18
18” long
46DVA-18B
TC-4DL1B
SV4LB12
—
—
94610612
—
4D12B
94610612B
94610618
—
—
—
4DT-18(B)
94610618B
Galvanized
46DVA-24
4DT-24
TC-4DL2
SV4L24
Black
46DVA-24B
4DT-24(B)
TC-4DL2B
SV4LB24
24” long
4D2
—
Galvanized
46DVA-36
4DT-36
TC-4DL3
SV4L36
Black
46DVA-36B
4DT-36(B)
TC-4DL3B
SV4LB36
94610624
—
4D2B
94610624B
4D3
—
94610636
—
4D3B
94610636B
Galvanized
46DVA-48
4DT-48
TC-4DL4
SV4L48
Black
46DVA-48B
4DT-48(B)
TC-4DL4B
SV4LB48
4D4
Roof Flashing
0/12-6/12
46DVA-F6
4DT-AF6
TF-4FA
SV4FA
—
4DF
(0/12-5/12)
—
949606012
Roof Flashing
7/12-12/12
46DVA-F12
4DT-AF12
TF-4FB
SV4B
—
4DF12
(6/12-12/12)
—
949606712
Flat Roof Flashing
46DVA-FF
—
TF-4F
SV4F
—
—
—
949606001
—
94610648
—
4D4B
94610648B
Masonry Flashing
—
—
TF-4MF
—
—
—
559FSK
—
New Siding Flashing
—
—
—
—
—
—
658NSFK
—
Wall Thimble
46DVA-WT
4DT-WT
TM-4WT
SV4RSM
—
4DWT
—
949064U
Storm Collar
46DVA-SC
4DT-SC
TM-SC
SV4AC
—
4DSC
—
94960608
Decorative Plate
46DVA-DC
4DT-CS
TM-4TR
TM-4TP
SV4PF
—
4DFPB
—
94940612
Cathedral Ceiling
Support
46DVA-CS
4DT-CCS
TM-4SS
—
—
4DRSB
—
949506KT
Ceiling Firestop /
Floor Support
46DVA-FS
4DT-FS
—
4DFSP
—
94980612
Attic Radiation Shield /
Firestop
—
—
94930620A
Wall Strap
46DVA-WS
4DTWS
TM-WS
—
—
4DWS
—
949164
Vinyl Siding Standoႇ
46DVA-VSS
4DT-VS
TM-VSS
SV4VS
—
4DHVS
—
94800615S
Elbow Strap / Oႇset
Support
46DVA-ES
4DT-OS
TM-OS
—
—
—
—
949264
Terminal Guard
46DVA-WG
—
—
—
—
TM-4RDS
SV4BF
TM-CS
SV4SD
TM-4AS
—
4DAIS12 (12”)
ADT-AIS
—
4DAIS36 (36”)
TM-HTS
TM-RHTS
62
—
94610609B
48” long
Notes:
—
94610609
—
36” long
Various Venting System Parts
—
4D7B
9” long
Black
BDM
MILES
INDUSTRIES
46DVA-06
Black
AMERIVENT
Galvanized
6” long
RLH
INDUSTRIES
SECURE
VENT
ICC EXCEL
DIRECT
SELKIRK
Venting Parts
Description
DURA-VENT
Venting Parts Code / availability by Manufacturer
845TG
940164SHRD
658TG
1. Follow instructions supplied with each manufacturer’s components.
2. Unless otherwise speci¿ed, all the parts and assemblies from the above table are to be used with 4” x 6-5/8” pipes.
3. Do not mix components from diႇerent vent manufacturers.
4. Termination caps manufactured by RLH Industries or American Metal Products are from Homestyle Chimney Collection and can be ordered in
one of the following ¿nishes: a) aluminium; b) black powder coated; c) solid copper.
Commonwealth of Massachusetts
State of Massachusetts Carbon Monoxide
Detector/Vent Terminal Signage
Requirements
For all side wall horizontally vented gas fueled
equipment installed in every dwelling, building or
structure used in whole or in part for residential
purposes, including those owned or operated by the
Commonwealth and where the side wall exhaust
vent termination is less than seven (7) feet above
finished grade in the area of the venting, including
but not limited to decks and porches, the following
requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS.
At the time of installation of the side wall horizontal
vented gas fueled equipment, the installing plumber
or gas fitter shall observe that a hard wired carbon
monoxide detector with an alarm and battery back-up
is installed on the floor level where the gas equipment
is to be installed. In addition, the installing plumber
or gas fitter shall observe that a battery operated
or hard wired carbon monoxide detector with an
alarm is installed on each additional level of the
dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be
the responsibility of the property owner to secure
the services of qualified licensed professionals for the
installation of hard wired carbon monoxide detectors.
a. In the event that the side wall horizontally vented
gas fueled equipment is installed in a crawl space or an
attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next
adjacent floor level.
b. In the event that the requirements of this subdivision
can not be met at the time of completion of installation,
the owner shall have a period of thirty (30) days
to comply with the above requirements; provided,
however, that during said thirty (30) day period, a
battery operated carbon monoxide detector with an
alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each
carbon monoxide detector as required in accordance
with the above provisions shall comply with NFPA 720
and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate
shall be permanently mounted to the exterior of the
building at a minimum height of eight (8) feet above
grade directly in line with the exhaust vent terminal for
the horizontally vented gas fueled heating appliance or
equipment. The sign shall read, in print size no less than
one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW.
KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the
side wall horizontally vented gas fueled equipment shall
not approve the installation unless, upon inspection,
the inspector observes carbon monoxide detectors and
signage installed in accordance with the provisions of
248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt
from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled
“Equipment Not Required To Be Vented” in the most
current edition of NFPA 54 as adopted by the Board;
and
2. Product Approved side wall horizontally vented gas
fueled equipment installed in a room or structure
separate from the dwelling, building or structure used
in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT
VENTING SYSTEM PROVIDED. When the manufacturer
of Product Approved side wall horizontally vented
gas equipment provides a venting system design or
63
Commonwealth of Massachusetts
venting system components with the equipment,
the instructions provided by the manufacturer for
installation of the equipment and the venting system
shall include:
1. Detailed instructions for the installation of the
venting system design or the venting system
components; and
2. A complete parts list for the venting system design or
venting system.
(d) MANUFACTURER REQUIREMENTS - GAS
EQUIPMENT VENTING SYSTEM NOT PROVIDED.
When the manufacturer of a Product Approved side
wall horizontally vented gas fueled equipment does
not provide the parts for venting the flue gases, but
identifies “special venting systems”, the following
requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions
shall be included with the appliance or equipment
installation instructions; and
2. The “special venting systems” shall be Product
Approved by the Board, and the instructions for that
system shall include a parts list and detailed installation
instructions.
(e) A copy of all installation instructions for all Product
Approved side wall horizontally vented gas fueled
equipment, all venting instructions, all parts lists
for venting instructions, and/or all venting design
instructions shall remain with the appliance or
equipment at the completion of the installation.
64
Appendix A—Lighting Instructions
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: ,I\RXGRQRWIROORZWKHVHLQVWUXFWLRQVH[DFWO\D¿UHRUH[SORVLRQPD\UHVXOW
FDXVLQJSURSHUW\GDPDJHSHUVRQDOLQMXU\RUORVVRIOLIH
A. This appliance has a pilot which must be lighted by hand, remote handset, or wall switch. Follow these
LQVWUXFWLRQVH[DFWO\7RVDYHJDVWXUQWKHSLORWRႇZKHQQRWXVLQJWKHDSSOLDQFHIRUDSURORQJHGSHULRGRIWLPH
B. BEFORE LIGHTINGVPHOODOODURXQGWKHDSSOLDQFHDUHDIRUJDV%HVXUHWRVPHOOQH[WWRWKHÀRRUEHFDXVH
VRPHJDVHVDUHKHDYLHUWKDQDLUDQGZLOOVHWWOHRQWKHÀRRU
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
‡,PPHGLDWHO\FDOO\RXUJDVVXSSOLHUIURPDQHLJKERU¶VSKRQH)ROORZWKHJDVVXSSOLHU¶VLQVWUXFWLRQV
‡,I\RXFDQQRWUHDFK\RXUJDVVXSSOLHUFDOOWKH¿UHGHSDUWPHQW
&8VHRQO\\RXUKDQGWRSXVKLQRUWXUQWKHFRQWURONQREV1HYHUXVHWRROV,IWKHNQREVZLOOQRWSXVKLQRUWXUQE\
KDQGGRQ¶WWU\WRUHSDLUWKHPFDOODTXDOL¿HGVHUYLFHWHFKQLFLDQ)RUFHRUDWWHPSWHGUHSDLUPD\UHVXOWLQD¿UHRU
explosion.
''RQRWXVHWKLVDSSOLDQFHLIDQ\SDUWKDVEHHQXQGHUZDWHU,PPHGLDWHO\FDOODTXDOL¿HGVHUYLFHWHFKQLFLDQWR
LQVSHFWWKHDSSOLDQFHDQGWRUHSODFHDQ\SDUWRIWKHFRQWUROV\VWHPDQGDQ\JDVFRQWUROZKLFKKDVEHHQXQGHUZDWHU
LIGHTING INSTRUCTIONS
1. STOP!5HDGWKHVDIHW\LQIRUPDWLRQDERYH
RQKDQGVHW 2. 72&/($5$1<*$6WXUQPDLQYDOYHRႇE\SUHVVLQJ3RZHUEXWWRQ
• :DLW¿YH PLQXWHVWRFOHDURXWDQ\JDVWKHQVPHOOIRUJDVLQFOXGLQJQHDUWKHÀRRUIf you
1
VPHOOJDV6723)ROORZ³%´LQWKHVDIHW\LQIRUPDWLRQDERYHRQWKLVODEHO,I\RXGRQ¶WVPHOO 2))
gas, go to the next step.
3. AUTOMATIC IGNITION: 0$1NQRE LQ21SRVLWLRQ(QVXUH)ODPH$GMXVWPHQW
)LJ
NQRE LVVHWWRORZHVWVHWWLQJ 3 )LJ /RFDWHWKHSLORW )LJ LQVLGHRI
¿UHER[
• 2QWKHKDQGVHWSUHVVWKH3RZHUEXWWRQ
DVKRUWDFRXVWLFVLJQDOFRQ¿UPVWKH
start has begun.
• Further short acoustic signals indicate the ignition process is in progress.
Spark
• :KHQWKHSLORWLVOLWWKH)ODPH$GMXVWPHQWNQRE ZLOODXWRPDWLFDOO\URWDWHWRWKH
highest setting.
• 3UHVVWKH'RZQEXWWRQ
RQWKHKDQGVHWWRUHGXFHWKHÀDPHKHLJKW
4. MANUAL IGNITION: 0$1NQRE LQ0$1SRVLWLRQ )LJ :LWKWKHIURQWDQGVLGH
Fig 3
ZLQGRZVDQGIURQWVLOORႇORFDWHWKHSLORW )LJ LQVLGHRI¿UHER[DWWKHIURQW
• 6HW)ODPH$GMXVWPHQWNQRE WRWKHORZHVWVHWWLQJ 3 • 3XVKGRZQWKHPHWDOOLFFRUH ZLWKDSHQRUVLPLODULQVWUXPHQWWKLVZLOOHVWDEOLVK Fig 2
WKHSLORWJDVÀRZ
• /LJKWJDVDWWKHSLORW ZLWKDPDWFK
• &RQWLQXHKROGLQJGRZQPHWDOFRUH IRUDERXWVHFRQGVDIWHUUHOHDVHSLORW
should remain lit.
• ,IWKHSLORWZLOOQRWVWD\OLWDIWHUVHYHUDOWULHVWXUQWKHJDVFRQWURONQRE WR2))
3 DQGFDOO\RXUORFDOVHUYLFHWHFKQLFLDQRUJDVVXSSOLHU
• 5HLQVWDOOWKHZLQGRZDQGVHWWKH0$1NQRE WR21WXUQ)ODPH$GMXVWPHQWNQRE XS 4 RUGRZQ 3 PDQXDOO\RUXVHWKH8S'RZQEXWWRQV / EXWWRQVRQWKHKDQGVHWWRDGMXVWWKHÀDPHKHLJKW
TO TURN OFF GAS TO APPLIANCE
AUTOMATIC SHUT-OFF XVLQJWKHKDQGVHW • 3UHVVDQGKROGWKH'RZQEXWWRQ
RQWKHKDQGVHWWRVKXWRႇWKHPDLQEXUQHUJDVÀRZ
• 3UHVV3RZHUEXWWRQRQKDQGVHWWRVKXWRႇWKHDSSOLDQFHLQFOXGLQJSLORWÀDPH
65
Appendix B—Remote Control Operation
Initial Pairing
Before the remote control can be used with the fireplace, it must be paired. See page 56.
Remote Control Operation
NOTE: Before using the remote control system for the first time, the receiver and the handset must be paired. See
the section Remote Control Initial Pairing on the ȴrst page of this manual.
Main Display
Child Proof
Time
Signal Indicator
Thermostatic Mode
Battery Status
AM
PM
Fan (if included)
Countdown Timer
°F or °C
Light
ON
OFF
Program Mode
Eco Mode
Temperature
Auxiliary Feature (not used)
To Turn On Fire
NOTE: When pilot ignition is conȴrmed, motor
automatically turns to maximum ȵame height.
One-Button lighting (default):
Two-Button lighting:
+
simultaneously
Press and hold for 4 seconds, until 8
short beeps and a blinking series of
lines conȴrms the start sequence has
begun. Release button.
Main gas ȵows once pilot ignition is
conȴrmed.
Handset automatically goes into
manual mode after main burner
ignition.
Standby Mode (Pilot Flame)
Press and hold
pilot ȵame.
66
to set appliance to
CAUTION: If the pilot does not stay lit after
several tries call your local service technician or
gas supplier.
To Turn O΍ Fire
Press
to turn OFF.
Note: There is a 2 minute delay after
switching o΍ before the next ignition is
possible.
CAUTION: Always check the ȴre and pilot visually to ensure they are o΍.
Flame Height Adjustment
To increase ȵame height, press and
hold .
To decrease ȵame height, press and
hold . You may hold the button
down until the ȴre is set to pilot ȵame
only.
AM
Appendix B—Remote Control Operation
Designated Low Fire and High Fire
To go to low ȴre, double-click
is displayed.
. “LO”
To deactivate functions:
AM
2. While the icons are ȵashing, press the relevant function button and hold for 10 seconds.
Note: Flame goes to high ȴre ȴrst
before going to low ȴre.
To go to high ȴre, double-click
is displayed.
1. Install batteries. All icons are displayed and ȵashing.
3. The function icon will ȵash until deactivation is complete. Deactivation is complete when the function
icon and two horizontal bars (
) are displayed.
. “HI”
AM
Note: If a deactivated button is pressed, there is no
function, and the two horizontal bars are displayed.
To activate functions:
1. Install batteries. All icons are displayed and ȵashing.
2. While the icons are ȵashing, press the relevant function button and hold for 10 seconds.
Choosing 1-Button or 2-Button Ignition
On the remote control handset, you can choose a
1-button or 2-button ignition. You can also choose to
activate or deactivate some of the functions. By default,
the handset is set to a 1-button ignition.
3. The function icon will continue to ȵash until activation is complete, and then turn solid. Activation is
complete when the function icon is displayed.
Setting Celsius or Fahrenheit
To change between °C and °F, press
and hold
+
simultaneously.
To change from 1-button to 2-button ignition, remove
the batteries, wait 10 seconds, reinsert batteries, and
immediately when the display ȵashes, press and hold
the
button for 10 seconds. ON is displayed and 1 is
ȵashing. When change is complete, 1 changes to 2.
Note : °C = 24-hour clock
°F = 12-hour clock
To change from 2-button to 1-button ignition, proceed
the same as above. ON is displayed and 2 is ȵashing.
When change is complete, 2 changes to 1.
1. Press
+
simultaneously.
Day ȵashes.
Deactivating or Activating Functions
These functions are active by default, but can be
deactivated at any time:
•
•
•
•
•
•
Child Proof
Program Mode
Thermostatic Mode
Eco Mode
Circulating Fan Operation
Countdown Timer
PM
Setting the Time
AM
PM
2. Press
+
to select a number
to correspond with the day of the
week.
•
•
•
•
•
•
•
1 = Monday
2 = Tuesday
3 = Wednesday
4 = Thursday
5 = Friday
6 = Saturday
7= Sunday
3. Press
+
simultaneously. Hour ȵashes.
4. To select hour press
5. Press
+
or
.
simultaneously. Minutes ȵash.
6. To select minutes press
7. To conȴrm, press
+
or
.
simultaneously or wait.
67
Appendix B—Remote Control Operation
Child Proof
Light/Dimmer Operation (not available)
Your handset can be set to lock out all commands to the
ȴreplace, except OFF.
On:
To turn Child Proof ON:
1.
2.
Press and hold
+
simultaneously.
is displayed. Child Proof is now active.
To turn Child Proof OFF:
1. Press and hold
2.
+
simultaneously.
disappears. Child Proof is now inactive, and the
handset has full function.
Countdown Timer
You can set your ȴreplace to automatically turn o΍ at
the end of a timer.
To set a Countdown Timer:
1. Press and hold
until
is displayed.
Hour ȵashes.
2. Press
or
to select Hour.
3. To conȴrm, press
.
Minutes ȵash.
4. Press
or
to select Minutes.
5. To conȴrm, press
or wait.
AM
Press
, is displayed. Light is on at
preset level.
Off:
Press
,
disappears. Light turns o΍.
Setting:
1. Press and hold
until
ȵashes.
2. To adjust light between 20-100% press
3. To conȴrm setting either press
is displayed.
or
.
or wait.
Note: The light works independently of the pilot ȵame.
If you want the light on but no ȵame, press
button.
Circulating Fan Operation (if installed)
Setting:
1. Press and hold
until
2. Press
to increase or
crease fan speed.
ȵashes.
to de-
3. To conȴrm setting, either press
or wait.
is displayed.
Off:
To turn off a Countdown Timer:
Press
1. Press
Note: When setting, if the fan was not switched o΍
after last use, it starts automatically 4 minutes after
ignition at maximum speed, and goes to the last set
level after 10 seconds. The fan stops 10 minutes after
the gas is OFF or at pilot.
, and the
countdown disappears.
Note: The Countdown Timer only works in Manual,
Thermostatic, and Eco modes. Maximum countdown
time is 9 hours and 50 minutes.
68
until all 4 speed level bars disappear.
Appendix B—Remote Control Operation
Modes of Operation
Thermostatic Mode
Thermostatic Mode
The room temperature is measured and
compared to the set temperature. The
ȵame height is automatically adjusted
to achieve the set temperature.
PM
Press
. is displayed. Preset
temperature displays brieȵy, followed
by the room temperature.
Setting Desired Temperature:
1.
Program Mode
The temperature is controlled by
Programs 1 and 2, each of which can be
set to go on and o΍ at speciȴc times, at
a set temperature.
PM
ON
OFF
Press and hold
until is displayed and set temperature
ȵashes.
2. To adjust set temperature, press
or .
3. To conȴrm, press
or wait.
Off:
Eco Mode
Flame height modulates between high
and low. If the room temperature is
lower than the set temperature, the
ȵame height stays on high for a longer
period of time. If the room temperature
is higher than the set temperature,
the ȵame height stays on low for a
longer period of time. One cycle lasts
approximately 20 minutes.
PM
On:
PM
If any of the above modes (Thermostatic, Program, or Eco) are engaged by the MyFire app over
WiFi, the handset will display APP.
1. Press
.
2. Press
or
3. Press
to go to Program Mode.
4. Press
to go to Eco Mode.
to go to Manual Mode.
Program Mode
On:
Press
.
, 1 or 2, ON or OFF are displayed.
PM
ON
OFF
Off:
1.
Press
Mode.
,
, or
to go to Manual
2. Press
to go to Thermostatic Mode.
Manual Mode
3. Press
to go to Eco Mode.
The on/o΍ status of the ȴreplace, as well as ȵame
height, are manually controlled by the user.
Note: The set temperature for Thermostatic Mode is
the temperature for the ON time in Program Mode.
Changing the Thermostatic Mode set temperature also
changes the ON time temperature in Program Mode.
Default Settings:
•
ON TIME (Thermostatic) TEMPERATURE: 70°F / 21°C
•
OFF TIME TEMPERATURE: “
” (pilot ȵame only)
69
Appendix B—Remote Control Operation
Temperature Setting:
Off Time Setting (PROGRAM 1)
1. Press and hold
until
ȵashes.
ON and set temperature (set in Thermostatic Mode) is displayed.
1.
ON
or wait.
,
2. To continue, press
OFF displayed, temperature ȵashes.
4. To select minutes, press
.
Note: The on (Thermostatic) and o΍ set temperatures
are the same for each day.
Day Setting:
1. ALL ȵashes. Press
choose between:
or
ALL = same settinΑs ON-OFF
every day
•
SA:SU = same settinΑs ONOFF Saturday and Sunday
•
1, 2, 3, 4, 5, 6, 7 = daily timer—unique ON-OFF
settinΑs for a sinΑle day of the week, for multiple
days of the week or for every day of the week.
.
, 1, ON are displayed. ALL is displayed brieȵy.
Hour ȵashes.
or
5. To conȴrm, press
.
5. To conȴrm, press
or
.
.
Note: Either continue to PROGRAM 2 and set ON and
OFF times or stop programming at this point, and
PROGRAM 2 remains deactivated.
The batteries must be removed to clear the
PROGRAM 1 and PROGRAM 2 ON and OFF times
and temperatures.
or
• Waiting to ȴnish setting.
Eco Mode
.
3. To conȴrm, press .
, 1, ON
are displayed. ALL displayed brieȵy.
Minutes ȵash.
4. To select minutes, press
OFF
• Set on time and o΍ time using the same procedure as
“ALL Selected” above.
On Time Setting (PROGRAM 1)
2. To select hour, press
.
SA:SU or Daily Timer (1-7) Selected
ALL Selected
1.
or
Note: PROGRAM 1 and 2 use the same ON
(Thermostatic) and OFF temperatures. Once a new ON
(Thermostatic) and/or OFF temperature has been set,
that temperature becomes the new default setting.
Note: ON and OFF times programmed for PROGRAM 1
and PROGRAM 2 become the new default times.
to
•
2. To conȴrm, press
2. To select hour, press
3. To conȴrm, press .
, 1, OFF
are displayed. ALL displayed brieȵy.
Minutes ȵash.
3. Select o΍ temperature by pressing
or .
4. To conȴrm, press
, 1, OFF are displayed. ALL is
displayed brieȵy. Hour ȵashes.
.
ON
On:
Press
button to enter Eco Mode.
is displayed.
PM
Flame height modulates between high
and low every 20 minutes.
Off:
Press
70
button to exit Eco Mode.
disappears.
Appendix B—Remote Control Operation
Low Battery Indication
CAUTION: Do not use a screwdriver or other
metallic object to remove the batteries from the
battery holder or the handset. This could cause a
short circuit.
Handset
The battery icon
will show when the battery
needs to be replaced. Replace with two 1.5 V AAA
alkaline batteries.
Receiver
Frequent beeps for 3 seconds when the motor turns
indicate the batteries in the battery holder need to be
replaced. Replace with four 1.5 V AA alkaline batteries.
Low Battery Receiver
With low battery power in the battery holder, the
system shuts o΍ the ȴre completely. (This will not
happen if the power is completely interrupted.)
Seven Day Shut Off
The system shuts o΍ the ȴre completely if there is no
change in ȵame height for 7 days.
Automatic Turn Down
3 Hour No Communication Function
The valve will turn to pilot ȵame if there is no
communication between the handset and receiver
for a 3-hour period. The ȴre will continue to function
normally when communication is restored.
Automatic Shut O΍
Countdown Timer
At the end of countdown time period, the ȴre turns
o΍. The Countdown Timer only works in Manual,
Thermostatic, and Eco Modes. Maximum countdown
time is 9 hours and 50 minutes.
71
Appendix B—Remote Control Operation
Error Codes
In the event of an error condition with the handset or ȴreplace, the handset will display an error code.
Failure
Code
Message on
Handset
Duration of
Display
Symptom
Possible Cause
F04
F04
4 sec
•
No pilot ȵame within 30 sec
•
Note: after 3 failed ignition
•
Air in pilot supply line
sequences, F06 shown
•
No spark
•
F06
F06
4 sec
•
•
No gas supply
•
Reversed polarity in thermocouple wiring
3 failed ignition sequences
•
No gas supply
in 5 minutes
•
Air in pilot supply line
Fire is not responding, no
•
No spark
pilot ȵame
•
Reversed polarity in thermocouple wiring
•
Incorrect pilot oriȴce if valve has been
converted from LPG to NG or vice versa
F07
F09
F46
Low battery
symbol
Permanent
F09
4 sec
F46
•
Battery icon ȵashes on
•
Low battery in handset
handset display
4 sec
•
Fire is not responding
•
No electronic control of ȴre
•
Fire is not responding
•
Intermittent response
•
No electronic control of ȴre
•
Down arrow button
was not pressed during
pairing
•
Receiver and handset are not synced
•
No or bad connection between receiver and
handset
•
•
No power at receiver (batteries low)
Low communication range (mains adapter
faulty, handset not communicating with
receiver)
72
Appendix C—Wall Switch Operation
The Wall Switch can be used to
control your fireplace. You can
turn the pilot on or off and you can
increase or decrease the flame height.
Adjusting Flame Height
Press and hold large flame
button
to gradually increase flame height.
Note that the thermostat and
programming functions are not
available with the wall switch.
Turning Appliance ON and OFF
Press ON-OFF button once to light
pilot. Press again to shut off pilot.
Press and hold small flame
button
to gradually decrease flame height.
73
Appendix D—HeatShift™System
Planning Installation: Linear with HeatShift™
Instructions for use with the following Valor Heater Models: 1500, 1600, 1700 and 1800 J or K
Incompatible with earlier models: 1500I, 1600I, and 1700I
Application
The HeatShift™ system redistributes the warm air ȵow
away from the ȴreplace opening to a more desirable
location using natural convection without use of a fan.
Plenums LKD1, LDK3 or LDK4: the warm air ȵow is
relocated to a position higher up the wall, out the
sidewalls, or even to an adjacent room.
Termination Plates LDK7: the warm air ȵow is
discharged through a gap (min. 2-1/2”) between the wall
above the ȴreplace and the ceiling. LDK7’s discharge
opening must be located in the same room as the
fireplace.
The result is much cooler wall temperatures above the
ȴreplace opening for locating televisions, artwork, etc.
The 1595CFK or 1595CFKV2 Circulating Fan Kit are not
recommended when installing the HeatShift system.
Any kit, LDK1, LDK3, LDK4 or LDK7 may be used with
compatible model ȴreplaces L1, L2 or L3 listed above.
As a further option, the warm airȵow may be extracted
away from the duct kit plenum (LDK1 and LDK4 ONLY)
by connecting a 1270RBK Remote Blower Kit to the duct
kit plenum.
This kit is compatible with the listed ȴreplaces only.
Earlier version ȴreplaces will not accept the addition of
this kit.
Note: These instructions are to be used in conjunction
with instructions regarding ȴreplace installation in this
manual.
The use of this kit will permit lower mantel clearances
to be used—see Combustible Mantel Clearances in this
Appendix. These lower mantel clearances must ONLY
be used when the HeatShift system is installed and
the internal convection baffle has been removed.
Approvals
The LDK1, LDK3, LDK4 and LDK7 duct kits are CSA
approved for use only with Valor Series ȴreplaces listed
above—DO NOT use with any other models.
This HeatShift system may also be used to reduce
wall surface temperatures on approved outdoor
installations.
5-inch diameter duct used with this kit must be metal
and meet requirements of UL-181 Class 1 Air Duct.
Flexible aluminum duct is acceptable provided it meets
the UL-181 Class 1 requirements.
ɄWARNING
DO NOT cover or place objects in front of
or on top of air outlet(s). AVOID locating
outlet within 7 feet above ȵoor level as
discharge temperatures are hot!
ɄWARNING
ɄWARNING
All ȴreplaces listed above require the
removal of the internal convection
baɞe for this system to function
properly—read instructions carefully!
74
When placing discharge close to ceilings,
staining or streaking may occur on light
colored ceilings due to any dust, etc. in air
ȵow; placing plenum(s) lower on the wall
will help reduce the possibility of staining
or streaking.
Appendix D—HeatShift™System
Kits
There are 4 kits to choose from:
•
•
•
•
LDK1—48” Plenum
LDK3—14” Plenums (2), includes grilles
LDK4—38” Plenum
LDK7—Duct Termination Plates (2)—for wall valance
discharge ONLY
Kits Contents
LDK1
48” x 2”
LDK4
38” x 2”
4 take-off collars
included
4 take-off collars
included
LDK3
2 - 14” x 6”
15-3/4”
(400 mm)
7-3/4”
(197 mm)
4 take-off collars
included
2 - 14” x 6” grilles
included, white
LDK7
2 Duct termination plates
4 take-off collars
included
75
Appendix D—HeatShift™System
Optional accessories
•
•
•
LDK2—48” Finishing Frame, to use with LDK1
LDK5—38” Finishing Frame, to use with LDK4
LDK6— 5” dia Aluminum 2-ply Flex Kit—
2 x 10’–0” lengths, may be cut to required length
Kits Contents
39-5/8”
(1007 mm)
49-5/8”
(1261 mm)
LDK2 (supplied separately)
48” frame, white
LDK6
2 - 10’ x 5” (aluminum ȵex)
76
3-5/8”
(92 mm)
LDK5 (supplied separately)
38” frame, white
3-5/8”
(92 mm)
Appendix D—HeatShift™System
Suggested Conȴgurations
Not to scale
Corner installations
Front wall outlet using LDK1 or LDK4
Rear wall outlet using LDK1 or LDK4
Note: Fireplace vent may conȵict with plenum.
O΍set vent around plenum.
ɄWARNING
Side wall outlets using LDK3
Rear wall outlets using LDK3
Note - When using LDK7, the discharge opening
must be located in the same room as the fireplace.
With LDK7
The plenum duct kits are approved
for horizontal discharge ONLY. The
termination duct plates are approved
for vertical upward discharge ONLY. DO
NOT install plenum or termination plates
in ȵoor or ceiling. DO NOT COVER OR
PLACE objects in front of or on top of air
outlet(s). AVOID locating outlet within
7 feet of the ȵoor level as discharge air
temperatures are hot!
DO NOT DISCHARGE THROUGH
EXTERIOR WALLS!
NOTE This duct kit may also be used for outdoor
installations where reduced wall surface
temperatures above the unit are desired.
The discharge grilles must be located under
the weatherproof enclosure described in the
GV60CKO Outdoor Fireplace Conversion Kit
instructions.
77
Appendix D—HeatShift™System
Overview (applies to LKD1, LDK3 and LDK4 kits)
Ceiling
Min. 2-1/2”
clearance
to ceiling
Min. 30”, Max. 12’-0”
See table for offsets
Flexible or rigid,
5” diameter
UL-181, Class 1
Air Duct (4)
(use LDK6 kit
or equivalent)
Min. 1”
clearance to
combustibles
around pipe
Linear
14-1/2”
LX2 17”
Linear 32-3/8”
LX2 33-1/4”
Linear 8-1/2”
LX2 5-1/4”
Linear 9-3/8”
LX2 11”
78
Appendix D—HeatShift™System
Overview (applies to LDK7)
Ceiling
Min. 1”
clearance to
combustibles
around pipe
8-1/2”
14-1/2”
32-3/8”
Flexible or rigid,
5” diameter
UL-181, Class 1
Air Duct (4)
(use LDK6 kit
or equivalent)
Min. 30”, Max. 12’-0”
6HHWDEOHIRUR΍VHWV
Min. 14”
Min. 2-1/2” opening required at ceiling
NOTE Discharge opening must be located in the
same room as fireplace when using LDK7.
9-3/8”
79
Appendix D—HeatShift™System
Y
Vertical Rise
X
Max. Allowable
Horizontal
Offset
30”
24”
36”
36”
42”
48”
48”
60”
54”
72”
60”
84”
66”
96”
12’-0”
96” Max.
With Plenum
LDK 1, LDK 3 or LDK 4
Ceiling
Min. 2-1/2”
clearance
to ceiling
8”
Min. bend
radius
Support horizontal
sections of pipe using
strapping every 24”
+
5”
Min. 1”
clearance to
combustibles
around pipes
Vertical Rise
‘Y’
(Min. 30”
Max. 12’-0”)
4
5” Min. bend
radius
12
DO NOT RUN
pipe horizontal.
Minimum slope 4:12
+
Top of fireplace
Maximum allowable Horizontal Offset
‘X’
(offset for take-off
that’s furthest away)
With Plates
Min. 2-1/2” opening required at ceiling
LDK 7 - Duct
Termination Plates
14”
min.
Min. bend
radius
Support horizontal
sections of pipe using
strapping every 24”
+
5”
4
5” Min. bend
radius
12
DO NOT RUN
pipe horizontal.
Minimum slope 4:12
+
Top of fireplace
Maximum allowable Horizontal Offset
‘X’
(offset for take-off
that’s furthest away)
80
Ceiling
Min. 1”
clearance to
combustibles
around pipes
Vertical Rise
‘Y’
(Min. 30”
Max. 12’-0”)
Appendix D—HeatShift™System
Plenum Dimensions
LDK 1
3-5/8”
11-1/2”
7-7/8”
Top View
1/2” wallboard
11-1/2”
mounting
bracket and
1-1/2” standoff
48” LDK 1
CL
3”
1/2”
standoffs
2”
12” LDK 1
14” LDK 1
1/2”
standoff
12” LDK 1
8”
mounting
bracket and
1/2” standoff
4”
5” dia.
collars (4)
Front View
8”
Right Side View
6” knock-out
each end for
optional
1270RBK
connection
LDK 4
3-5/8”
11-1/2”
7-7/8”
Top View
1/2” wallboard
11-1/2”
mounting
bracket and
1-1/2” standoff
38” LDK 4
CL
3”
1/2”
standoffs
2”
5” dia.
collars (4)
1/2”
standoff
4”
8”
14”
Front View
8”
4”
8”
mounting
bracket and
1/2” standoff
4”
8”
Right Side View
6” knock-out
each end for
optional
1270RBK
connection
81
Appendix D—HeatShift™System
Plenum Dimensions (cont’d)
14”
LDK 3
1/2” wallboard
11-1/2”
mounting
bracket and
1-1/2” standoff
CL
3”
1/2”
standoffs
6”
1/2”
standoff
5” dia.
collars (2)
7”
Front View
8”
mounting
bracket and
1/2” standoff
Right Side View
9-3/4”
LDK7 Plates Dimensions
9-3/4”
2-1/2”
19-1/2”
Warning
Label
16”
Stand-offs
(fold down for shipping)
Stand-offs
13-1/2”
Top View
CL
5” dia.
collars (4)
4-1/2”
7”
4-1/2”
9-3/4”
9-3/4”
19-1/2”
Front View
82
Right Side View
Appendix D—HeatShift™System
Rough Frame Openings
LDK 1 = 49”
LDK 4 = 39”
LDK 3 = 15”
CL
Min. 1” below
finished ceiling
4”
8”
Framing on edge
5-1/2”
Min. 1” below
finished ceiling
Framing on edge
Top of
plenum
support
LDK 3
LDK 1 = 13”
LDK 4 = 11”
LDK 1 & LDK 4
Framing and Clearances—Plenums, front view
Rough Frame Opening
LDK 1 = 49”
LDK 4 = 39”
LDK 3 = 15”
Min. 1/2”
clearance to
combustibles
at ends
2 x 4 on edge
5”
Framing on edge
Rough
Frame
Opening
LDK 1 = 4”
LDK 4 = 4”
LDK 3 = 8”
See detail
2 x 4 on edge
!
See appliance’s
installation for
minimum
combustible
cavity dimensions
Note - Min. cavity
dimensions may
be dictated by
LDK plenum when
installing across
corners.
83
Appendix D—HeatShift™System
Framing and Clearances—Plenums, side view
LDK 1 & 4
Min. 2-1/2” clearance to ceiling
4”
Ceiling
1/2”
5”
Framing
“on edge”
1-1/2” min. clearance
to combustibles (top)
1/2” min.
clearance to
combustibles
rear & sides
Plenum
support
(wood)
Maintain 1”
clearance
to pipes
2” min. clearance
to combustibles
(use steel stud for
LX2 appliances)
1” min.
clearance to
combustibles
all around pipes
LDK 3
Min. 2-1/2” clearance to ceiling
8”
Ceiling
1/2”
2” min. clearance
to combustibles
(use steel stud for
LX2 appliances)
Framing
“on edge”
84
1-1/2” min. clearance
to combustibles (top)
1/2” min.
clearance to
combustibles
rear & sides
1” min.
clearance to
combustibles
all around pipes
Appendix D—HeatShift™System
Wall Valance Discharge Opening using LDK7—Duct Termination Plates
Minimum length
of opening, front
and sides
L1 & H5 - 1500 = 40”
L2 & H6 - 1700 = 50”
L3 - 1800 = 64”
2-1/2” min.
Ceiling
Note: Staining or streaking may
occur on light colored ceilings due
WRDQ\GXVWHWFLQDLUȵRZ
Maximizing the opening size will
help reduce any staining or
streaking.
LDK 7 - Duct
Termination Plates (2)
for horizontal
installation ONLY!
Combustible wall
construction
Continuous ceiling
UHTXLUHGZLWKLQFDYLW\
3ODWHVWDQGR΍
See clearances
to combustibles
next page
4”
14” min.
:DOOȴQLVKUHTXLUHG
to form plenum
above duct
termination plates
2 x 4 on edge to support
plates as necessary maintain 1” clearance to pipes
Min. 1” clearance
around pipes
Vertical vent can pass between
duct termination plates
7RSRIVWDQGR΍V
See installation manual packed
with appliance for minimum
combustible cavity dimensions
Non-combustible
cement board
85
Appendix D—HeatShift™System
LDK7 Clearances to Combustibles
4”
Perimeter of plates
may be trimmed to
suit installation
4”
19-1/2”
4”
Stand-off
4”
Stand-off
16”
Non-combustible
zone above plates
Top View
4”
4”
4”
4”
13-1/2”
13-1/2”
Stand-offs
Combustible framing
allowed below plates
5” dia. pipes maintain 1” clearance
to combustible materials
Front View
86
Right Side View
Appendix D—HeatShift™System
LDK Duct Kit LDK 1, LDK 4 with optional 1270RBK Remote Blower Kit
(not approved with outdoor installations)
8QLYHUVDOWDNHR΍VXSSOLHGZLWK5%.NLW
&DQPRXQWWRHLWKHUHQGRISOHQXP
0D[LPXP[5%.NLWSHUSOHQXP
1RWH'2127&211(&75%.GLUHFWO\
WRȴUHSODFHZKHQXVLQJ/'.'XFW.LW
6HHLQVWDOODWLRQLQVWUXFWLRQVSDFNDJHG FRQQHFWWR/'.SOHQXP21/<DVWKLVZLOO
ZLWKWKH/'.'XFW.LWV
HQVXUHFRROHUZDOOWHPSHUDWXUHZKHWKHURU
QRWWKHIDQLVUXQQLQJ
LDK1 or LDK4 plenum
ȋGLDSLSLQJ
/LQHDU----ȴUHSODFHV
5%.IDQXQLW
VHHGLDJUDPIRU
SRVVLEOHPRXQWLQJ
SRVLWLRQV0D\EH
SRVLWLRQHGKLJKHU
RUORZHUWKDQ
/'.SOHQXPSRVLWLRQ
/LQHDU....ȴUHSODFHV
87
Appendix D—HeatShift™System
COMBUSTIBLE Mantel Clearances Linear appliances (when using HeatShift System ONLY)
Sidewall clearances remain as stated in this installation manual.
NOTE: These Mantel Clearances
apply ONLY when LDK Duct
system is installed
ɄWARNING
RISK OF OVERHEATING
AND FIRE! Ensure HeatShift
installation is complete AND
internal convection baɞe
is removed (see HeatShift
installation) when using
these combustible mantel
clearances.
Combustible
materials must
be kept behind
this line
45°
10”
Mantel
33-3/4” Height
(from
Bottom
29-3/4” of Unit)
6”
23-3/4”
1” trim
4” minimum to
combustible
hearth
14-1/4”
Opening in Trim
1” trim
9-1/2”
Cement board as specified
in installation manual
packed with appliance
Note: Combustible
wall finish up to
1” thick may be
installed over
cement board
and butt up to
the 1” trim all
around the opening.
DO NOT COVER
THE TRIM
Bottom of Unit
NON-COMBUSTIBLE Flush Hearth/Mantel Projections (when using HeatShift System ONLY)
1” Trim
Max. 6” non-combustible
projection allowed top and
bottom, at edge of 1” trim.
Only allowed when using
LDK Duct kit.
88
Appendix D—HeatShift™System
Remove Convection Baɞe
Appliance front panel—shown transparent for clarity
To be e΍ective the LDK Duct Kit requires that a
convection baɞe located above the ȴrebox inside the
appliance case be removed to allow the hot airȵow to
convect upwards into ducts installed on the ȴreplace.
Take-off
collar
Convection
baɞe to be
removed
Co
n
vec
t io
nb
af f
le
Convective
airflow with
baffle removed
Convective
airȵow with
baɞe in place
Remove convection baɞe—
1500, 1700, 1800 J or K
Appliance front
panel—shown
transparent for clarity
Firebox
Co
n
vec
t io
nb
af f
le
Re-direction of convected air after removing baɞe
!
Remove the convection baɞe from the
appliance. It is held in place by screws located
right behind the upper edge of the ȴreplace
opening (3 screws/baɞe). Recycle this panel
as it is no longer needed.
Co
n
vec
t io
nb
af f
le
Remove 2 convection baɞes,
one on each side—1600J or K
89
Appendix D—HeatShift™System
Install HeatShift collars
1. Remove the four cover plates on top of the appliance case (6 screws each).
2. Install the collars on the holes on top of the appliance’s case (6 screws each).
1500, 1700, 1800 J or K
1500, 1700, 1800 J or K
1600 J or K
ɄWARNING
All FOUR (4) takeoffs MUST BE
CONNECTED TO PLENUM(S).
90
1600 J or K
ɄWARNING
DO NOT INSTALL 1270RBK Remote Blower
Kit to any of these 4 takeo΍s.
Appendix D—HeatShift™System
Install Plenum Kits (LDK1, LDK3 & LDK4)
—see next page for LDK7 Duct Termination
Plates
1. Frame a rough opening at the desired location—see
earlier sections of this manual for allowable plenum
positions and rough frame opening sizes.
2. Install top mounting bracket(s) to the plenum using
screws provided (use the short sheet metal screws
provided otherwise the screw tails (ends) will interfere with the ȴnishing frame when installed).
Note: The ȵanges of the white ȴnishing frame (when
used) will insert approximately 1-1/4” into the plenum covering the shiny sheet metal.
7. Install the ȴnishing frame or louver to the plenum
after the wall ȴnish is completed:
LDK1, LDK4: Use the LDK2 or LDK5 depending of the
length of the plenum.
LDK3: Use the grilles provided with the kit.
Note: The frame/louver are ȴnished white but may
be painted another color if desired; use high temperature paint (250ºF). You may also ȴnish up to the
perimeter of the plenum opening with your material
of choice and not use the frame or louver. Do not
ȴnish over any of the opening in the plenum outlet.
3. Install the plenum(s) into the rough frame opening
maintaining minimum clearances to combustibles
as listed—see page 10. Fix the plenum to the framing using nails or screws through the top mounting
bracket. Note that the mounting brackets are not
intended to carry the weight of the plenum and
pipes. Provide support to the underside of the
plenum and ensure the plenum is level and its
outlet is not distorted (see detail on page 11). Use
metal strapping (all-round, not supplied) as required
to further secure the plenum to framing.
8. Continue with the ȴreplace installation.
4. Attach one section of UL-181, Class 1 approved air
duct to each of the collars and secure it with gear
clamps provided. DO NOT SPLICE DUCTS!
5. Attach the top of the pipe sections to the plenum
securing them with the gear clamps provided. An
upward slope must be maintained in horizontal sections of pipes for proper convection. Use straps as
necessary to maintain the pipes positions. Support
horizontal sections every 24 inches.
6. Paint the inside surfaces of the plenum using hightemperature ȵat black spray paint for installations
where the inside of the plenums may be visible.
91
Appendix D—HeatShift™System
Install Duct Termination Plates (LKD7)
—see previous page for LDK1, LDK3 & LDK4
Plenum kits
1. Frame a rough opening and platform at the desired
location—see earlier sections of this manual for allowable duct termination plates positions and rough
frame opening sizes.
2. On each duct termination plate, rotate both stando΍s to the vertical position and secure in place using
screws provided.
2 stand-offs per plate
Repair Parts List
Description
LDK1
48” Quad Hot Air Plenum Kit
48” x 2” quad plenum
4005476
5” take-off collars (4)
4005478
Top mounting bracket/standoffs
4007211
#8 slotted drive screws 1/4” (7)
798601
LDK2
48” Outlet Frame Kit for LDK1
LDK3
14” Double Hot Air Plenums Kit
Aux Frame-SPL 48” x 2” white
3. Install the termination plates into the framing ensuring collars/pipes on underside of plates maintain
1 inch clearance to combustibles and clearance to
combustible above the plates are maintained as
listed on page 13.
The termination plates perimeter may be trimmed
as necessary to accommodate framing. Secure the
termination plate to framing using screws or nails to
avoid movement.
4. Attach one section of UL-181, Class 1 approved air
duct to each of the collars and secure it with gear
clamps provided. DO NOT SPLICE DUCTS!
5. Attach the top of the pipe sections to the duct termination plates securing them with the gear clamps
provided. An upward slope must be maintained in
horizontal sections of pipes for proper convection.
Use straps as necessary to maintain the pipes positions. Support horizontal sections every 24 inches.
6. Continue with the ȴreplace installation.
92
LDK5
4005464
5” take-off collars (4)
4005478
DABL-00-C-SPL 14” x 6” Grilles white (2)
4005614
Top mounting bracket/standoffs (2)
4005566
LDK7
798601
38” Quad Hot Air Plenum Kit
38” x 2” quad plenum
4005477
5” take-off collars (4)
4005478
Top mounting bracket/standoffs
4007213
#8 slotted drive screws 1/4” (7)
798601
38” Outlet Frame Kit for LDK4
Aux Frame-SPL 38” x 2” white
LDK6
4005612
14” x 6” double plenums (2)
#8 slotted drive screws 1/4” (6)
LDK4
Part no.
4005613
5” Aluminum 2-ply Flex Kit
5” dia 10’ (uncompressed) aluminum
chimney liners (2)
4005635
4.5” - 6.5” ss gear clamps (8)
4005642
Duct Termination Plates
Plate and collar assembly (2)
4006747
5” take-off collars (4)
4005478
Screws 8 x 3/8 tap PN HD PH (12)
100A757
Each LDK kit is sold separately.
Appendix D—HeatShift™System
LDK1
LDK4
LDK5
LDK2
LDK6
LDK3
LDK7
93
Appendix E—Spare Parts
Description
Part No.
1
Heat shield
4003049
2
45 degrees flanged elbow
3
Elbow gasket
4002999
39
Air shutter
4
Top stand-off s (2)
4005408
40
Burner module plate
4006916
5
Restrictor plate
4003017
41
Gaskets module plate, short (2)
3000399
6
Cover plates (4)
4005409
42
Gaskets module plate, long (2)
3000400
7
Take-off cover (2)
4003046
43
Air shutter lever
4007225
8
Liner panels anchors (2)
4001283
44
#10 * 1/2 Flat washers (2)
4006692
9
LH Window latch assembly
4002770
45
3/16” * 9/16” Spring washers (2)
4006691
10
RH Window latch assembly
4002766
46
#10-24 Zinc finish steel reverse nuts (2)
4007890
11
Convection baffle
4005400
47
Gas supply pipe assembly
4006923
12
Cable hole cover
4003038
48
Valve mount
4002905
0945M
13
Top panel support
4002963
14
Bracket - stiffener
4007949
15
Bracket - support
4007950
16
Window assembly
4003567X
17
Hot glass warning plate
18
Black metal platform
4004138AH
19
Burner rail assembly
4006900AH
20
Platform support
4002908
21
Burner end location bracket
4002903
Burner module assembly
(natural gas)
4006922
22
23
24
24a
24b
25
26
27
28
Burner module assembly
(propane gas)
Pilot shield
4003093
4007736
4003018AH
Pilot assembly (natural gas)
4006738
Pilot assembly (propane gas)
4006739
Plug pilot
4000726
Pilot assy injector #51 (natural gas)
4000727
Pilot assy injector #30 (propane gas)
4000728
Thermocouple
4000061
Pilot injector #51 (natural gas)
4000735
Pilot injector #30 (propane gas)
4000736
Pilot tube
4000732
Pilot hood 2-flame
4000730
29
Extended nut
4001855
30
Electrode
4001856
31
Pilot gaskets (2)
4000715
32
Pilot stand
4006907
33
Platform support
4002908
34
Burner mounting bracket A
4006918
35
Burner mounting bracket C
4007223
36
L2 Air shutter stopper
4008005
37
Injector/Burner mount
4007702
94
Description
38
Part No.
Gas orifice DMS #32 (natural gas)
4007000-32
Gas orifice DMS#49 (propane gas)
4007000-49
4007748
GV60 valve assembly (natural gas)
4003986X
49
GV60 valve assembly
(propane gas)
4003987X
50
Thermocouple interrupter
4001037
51
Pipe s/s flex
4000345
52
Receiver Valor 10 Two Way
4005597
53
Wire harness GV60
4001187
54
Yellow cable to interrupter
4002096
55
Red cable to interrupter
4001035
56
Ignition cable sleeve 530 mm
4002244
57
58
Ignition cable 500 mm
4001039
Valor 10 handset wall holder
4004459
59
Valor 10 button handset black
4007548
60
Remote battery & Wall switch kit
60a
Junction box
RBWSK
4005527
60b
Cover plate & 4 screws
4005526
60c
Battery holder
4005525
60d
Cable tie
4005524
60e
Harness assembly
4005523
60f
Plate with magnets
4005391
60g
Long screws (2)
4001444
60h
Wall switch with 2 screws
4005522
60i
Battery cover assembly
4005390
62
Liner panels - complete set
Fluted Black Liners
63
1715FBL
Reflective Glass Liners
1725RGL
Limestone Liners
1735LML
Stacked Stones Liners
1740SSL
Rear panel
Fluted Black - centre panel only
4003955
Glass (3)
4004275
Limestone - centre panel only
Stacked Stones - single rear panel
4005893G
4008045
Appendix E—Spare Parts
Description
63a
Fluted Black - sides (2)
Glass
Limestone - sides (2)
Stacked Stones
64
Glass
Limestone
Stacked Stones
Glass
Limestone
Stacked Stones
67
Description
Part No.
Rocks & Shale Set
1714RSS
4003727
85
LH twig
4001827
-
86
LH twig - short (2)
4001827S
4005892G
87
RH twig (2)
4001828
-
88
Grey Rock S4-A (7)
4002338
89
Dark Grey Rock S4-A (5)
4002339
4003071
90
Grey Rock S4-B (5)
4002340
4004273
91
Dark Grey Rock S4-B (8)
4002341
4003071G
92
No 7 Grey 5 Matte pitted rock
4002650
4008026
93
No 9 Grey 5 Matte rock (2)
4002652
RH side panel
Black
66
84
LH side panel
Black
65
Part No.
Rear panel
94
No 11 Grey 3 Matte rock (2)
4002654
4003072
95
No 14 Grey 9 Gloss rock
4002657
4004274
96
No 16 Warm Grey 3 Gloss pitted rock (2)
4002659
4003072G
97
No 17 Grey 5 Gloss pitted rock
4002660
4008027
Top panel
98
99
Shale 3/4” - grey, black 0.5lb ea
Split Wood Kit
4004792
1700SWK
Black (2)
4003728
100
Splinters grey, bagged
4005813
Black (2)
4003728
101
Small embers, bagged
4006134
Black (2)
4003728
102
Split Wood Logs
Stacked Stones (2)
4008044
Log #1
4006122
1700DGM
Log #2
4006123
Glass panel 401 x 66 mm
4003746A
Log #3
4006124
68b
Glass panel 401 x 82 mm
4003746B
Log #4
4006125
68c
Glass panel 119.5 x 46 mm
4003746C
Log #5
4006126
68d
Glass panel 119.5 x 78.5 mm
4003746D
Log #6
4006127
68e
Glass panel 384.5 x 66 mm (2)
4003746E
Log #7
4006128
68f
Glass panel 384.5 x 82 mm (2)
4003746F
Log #8
4006129
4004521
Log #9
4006130
1705DWK
Log #10
4006131
68a
69
70
Murano Glass Fire
4006196
Classic 1/2” clear fireglass
Driftwook Kit
71
Rear log
4002938
72
LH end log
4002965
Log #11
73
LH front log
4002967
105
Mixed grey embers, 8-cup bag
4008046
74
Center cross log
4003721
106
Splinters grey
4005813
75
RH rear log
4003928
Birch Log #L1
4007371
76
RH Cross log
4003929
Birch Log #L2
4007372
77
Brown beach pebble
4003082
Birch Log #L3
4007373
78
Grey beach pebble (2)
4003083
Birch Log #L4
4007374
79
Small grey beach pebble
4003086
Birch Log #L5
4007375
80
White beach pebble (2)
4003084
Birch Log #L6
4007376
104
Birch Logs Kit
4006132
1700BLK
81
Black beach pebble (2)
4003085
Birch Log #L8
4007378
82
Small beige beach pebbles (2)
4003087
Birch Log #L9
4007379
83
Grade 1A vermiculite, bagged
4002940
Birch Log #L12
4007382
107
GV60 Valve Repair Kit
4004544
95
Appendix E—Spare Parts
1
66
62
4
6
2
5
3
64
63a
66
6
63
4
63a
8
65
9
11
7
8
16
17
10
13
15
18
14
19
12
107
23
22
24-28
20
59
21
58
57
56
60
60e
32
33
34
35
36
37
38
60c
60g
40
60d
60b
47
53
41
60f
52
60h
39
42
51
96
55
54
60a
60i
31
29-30
48
50
49
43
44
45
46
Appendix E—Spare Parts
1700DGM
1700BLK
104
68c
67
68e
68f
68a
68b
69
68e
68f
68d
105
106
84
70
1705DWK
1714RSS
71
86
74
72
89
(7)
(5)
75
92
87
79 80
81 82
91
(5)
93
94
(2)
(2)
(8)
(2)
76
77 78
90
(2)
85
73
88
83
95
96
97
98
(2)
99
1700SWK
100
101
102
8
5
1
2
3
4
6
7
10
9
11
97
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising