Valor 716EH Installation instructions
Add to my manuals8 Pages
Valor 716EH
The Valor 716EH is a trim kit designed for use with Valor 700 fireplace models. It can be used with either the 717BPB or 719BPB backing plate, and can be further customized with additional backing plates and riser trims to cover larger cavity openings. The 716EH does not affect clearances or other specifications listed in the heater installation manuals.
Here are some of the key features and benefits of the Valor 716EH:
- It is designed to reduce the risk of burns from the hot viewing glass, making it a safer option for homes with children or other at-risk individuals.
- It is easy to install and can be customized to fit a variety of fireplace openings.
advertisement
L
EGEND
G3.5
716 Edgemont Hammered Trim Kit
Use with Valor 700 Models only
Installation Instructions for 716EHC, EHV, EHOZ, 717BPB and 719BPB kits
!
DANGER
HOT GLASS WILL
CAUSE BURNS.
I N S TA L L E R
Leave this manual with the appliance.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
C O N S U M E R
Retain this manual for future reference.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.
The 716 Edgemont Hammerered Trim Kit is intended to be used with the Backing Plate 717BPB or 719BPB installed on the Valor heater model 700.
The 716 fi tted with the 717 backing plate can also be installed with an additional backing plate 710BPB or
714BPB as well as a riser trim 725RT or 793RT to cover larger cavity opening.
36-1/4” (922 mm)
1-1/2”
(38 mm)
1/2”
(13 mm)
!
Please note the appliance will have to be raised by
2-5/8” when using the 719BPB 4-Sided Backing Plate as the plate extends below the bottom of appliance.
Mounting of the 716 does not affect clearances or other specifi cations listed in the heater installation manuals— see installation manual supplied with the heater for more information.
1-1/2”
(38 mm)
36-5/16” (922 mm)
1/2”
(13 mm)
716EH with 717BPB—
3-sided Backing Plate
4005661-02
© Copyright Miles Industries Ltd., 2016
716EH with 719BPB—
4-sided Backing Plate
!
2-5/8” (67 mm) between bottom of trim and bottom of appliance
Overview
717BPB Backing Plate
(sold separately)
LH side door
700 engine
RH side door
Edgemont hammered barrier screen door
716EH Edgemont Hammer with 717BPB 3-Sided Backing Plate
700 engine
719BPB Backing Plate
(sold separately)
LH side door
2
RH side door
Edgemont hammered barrier screen door
716EH Edgemont Hammer with 719BPB 4-Sided Backing Plate
Installation
1. Fit the 717BPB or 719BPB backing plate to the shrouds (side brackets) supplied with the fi replace with two screws per side.
Note: Use the upper hole in the backing plate to fi x it to the shrouds.
4. Insert the top pin of the left door panel in the hole at the top of the left shroud already installed on the appliance.
2. Identify the left and right door panels using the image below.
3. Identify the top and bottom of the left panel. The notch in the rear fl ange of the panel is at the top.
The space between the rear fl ange and the edge of the panel is wider at the top than at the bottom of the panel as shown below.
Left door panel
TOP of door: this space is wider
TOP of door: notch in the rear flange
5. Lift the panel as far as possible and insert the bottom pin in the hole at the bottom of the shroud.
The panel should rotate freely.
6. Install the right door panel the same way.
7. Hook the barrier screen door to the backing plate as indicated.
Note: The barrier screen door, when hooked to the backing plate, protrudes slightly in front of the plate.
BOTTOM of door: this space is narrower
Front view Rear view
3
Maintenance
To clean the backing plate, use mild soap and water.
You can dust the screen with a soft brush. To brush the back of the screen, simply unhook it.
To clean the window and ceramics inside the fi rebox, consult the Owner’s Information section of the
Installation and Owner’s Manual supplied with the fi replace.
DO NOT CLEAN THE GLASS WINDOW WITH
AMMONIA!
!
OR FIREPLACE WHILE THEY ARE HOT! Let the
Repair Parts List
Description Part Numbers
716EHV
Vintage
716EHOZ
Oil Bronze
716EHC
Copper plated
1 Barrier screen door 4005691V 4005691O 4005691C
2 LH access door
3 RH access door
4003296
4003298
4003296
4003298
4003296
4003298
2
3
Description Part Numbers
717BPB
4003838
719BPB
4005818 1 Backing plate
2 Convection baffl e 4003321BY 4003321BY
#8 1/2” screws (4) 4004560 4004560
1
716EH
2
2
1
1
717BPB (sold separately) 719BPB (sold separately)
Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication.
Designed and Manufactured by / for
Miles Industries Ltd.
190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1
Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com
4
®
L
EGEND
G3.5
LE PREMIER
FOYER À GAZ RADIANT MC
Bordure matelée Edgemont 716
Utilisez avec les foyers Valor Legend 700 seulement
Directives d’installation pour les kits 716EHC, EHV, EHOZ, 717BPB et 719BPB
!
DANGER
VITRE CHAUDE - RISQUE
DE BRÛLURES.
1-1/2”
(38 mm)
1/2”
(13 mm)
I N S TA L L AT E U R
Laissez cette notice avec l’appareil.
NE TOUCHEZ PAS UNE
VITRE NON REFROIDIE.
NE LAISSEZ JAMAIS UN
ENFANT TOUCHER LA VITRE.
L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de contact accidentel avec la vitre chaude et doit être installé pour la protection des enfants et des personnes à risques.
La Bordure martelée Edgemont 716 est conçue pour
être utilisée avec une Plaque de fi nition 717BPB ou
719BPB installée sur les foyers Valor 700.
Les Plaques de fi nition 710BPB ou 714BPB de même que les Bases de soulèvement 725 ou 793 peuvent
également être ajoutées au 716 combiné avec le 717 afi n de couvrir un âtre plus grand.
36-1/4” (922 mm)
!
C O N S O M M AT E U R
Conservez cette notice pour consultation ultérieure.
Veuillez noter que l’appareil devra être soulevé de
2-5/8” (67 mm) lorque la Plaque de fi nition à 4 côtés
719BPB est utilisée parce qu’elle dépasse le bas de l’appareil.
L’installation de la bordure 716 n’affecte pas les dégagements et autres caractéristiques indiqués dans le guide d’installation du foyer—consultez le guide d’installation pour plus d’information.
36-5/16” (922 mm)
1-1/2”
(38 mm)
1/2”
(13 mm)
716EH avec 717BPB—
Plaque de fi nition à 3 côtés
© Droits d’auteurs, Miles Industries Ltd., 2016
716EH avec 719BPB—
Plaque de fi nition à 4 côtés
!
2-5/8” (67 mm) entre le bas de la plaque et le bas de l’appareil
5
Concept
Plaque de fi nition 717BPB
(vendue séparément)
Foyer 700
Panneau d’accès gauche
Panneau d’accès droit
Pare-étincelles Edgemont
Bordure martelée Edgemont 716EH avec
Plaque de fi nition à 3 côtés 717BPB
Plaque de fi nition 719BPB
(vendue séparément)
Foyer 700
Panneau d’accès gauche
Panneau d’accès droit
6
Pare-étincelles Edgemont
Bordure martelée Edgemont 716EH avec
Plaque de fi nition à 4 côtés 719BPB
Installation
1. Fixez la plaque de fi nition 717BPB ou 719BPB aux supports des côtés déjà installés sur le foyer (2 vis par côté).
Note : Utilisez les trous supérieurs des montants de la plaque de fi nition pour la fi xer.
4. Insérez la cheville du haut dans le trou du support de devanture déjà installé sur l’appareil.
2. Identifi ez les panneaux d’accès gauche et droite à l’aide de l’image ci-dessous.
3. Identifi ez le haut et le bas du panneau de gauche.
L’encoche du rebord à l’arrière est en haut.
L’espace entre le rebord à l’arrière et le haut du panneau est plus large en haut qu’en bas.
Panneau d’accès gauche
HAUT du panneau : cet espace est plus large
HAUT du panneau : encoche dans le rebord arrière
BAS du panneau : cet espace est plus étroit
Avant Arrière
5. Soulevez le panneau et insérez la cheville du bas dans le trou du support. Le panneau devrait pivoter librement.
6. Installez le panneau droit de la même façon.
7. Accrochez le pare-étincelles à la plaque de fi nition tel qu’indiqué.
Note : Lorsqu’installé, le pare-étincelles dépasse légèrement le devant de la plaque de fi nition.
7
Entretien
Pour nettoyer la plaque de fi nition, utilisez une solution d’eau et de savon doux. Époussettez le pare-étincelles
à l’aide d’une brosse à poils doux. Pour brossez l’arrière du pare-étincelles, simplement décrochez-le.
Pour nettoyer la fenêtre et l’intérieur de la boîte de foyer, consultez la section Information à l’intention du consommateur dans le Guide de l’installation et du consommateur fourni avec le foyer.
NE NETTOYEZ PAS LA VITRE DE LA FENÊTRE
AVEC UN PRODUIT À BASE D’AMMONIAQUE!
!
NE TOUCHEZ PAS LE OU
Liste de pièces
Description
716EHV
Antique
1 Pare-étincelles
Edgemont
2 Panneau d’accès gauche
4005691V
4003296
3 Panneau d’accès droit 4003298
N o de pièces
716EHOZ
Bronze huilé
4005691O
716EHC
Plaquée cuivre
4005691C
4003296
4003298
Description N o de pièces
1 Plaque de fi nition
717BPB
4003838
719BPB
4005818
2 Défl ecteur de convection
4003321BY
Vis noires n o 8 1/2” (4) 4004560
4003321BY
4004560
4003296
4003298
1
716EH
2
3
2
2
1
1
717BPB (vendue séparément) 719BPB (vendue séparément)
Parce que nous favorisons une politique de développement continu, certains détails de la présente publication peuvent varier.
Conçue et fabriquée par / pour
Miles Industries Ltd.
190 – 2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1
Tél. 604-984-3496 Téléc. 604-984-0246 www.foyervalor.com
8
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project