ZTE | S319 | User manual | ZTE S319 User manual

ZTE S319 User manual
Security
 Keep your phone dry. Any liquid may damage your phone.
 Do not drop, knock or harshly treat the phone. Rough handling can
break internal circuit boards.
 Do not connect the phone with any incompatible enhancement.
 Do not attempt to disassemble the mobile phone or battery.
 Do not store the phone with flammable or explosive articles.
 Do not charge the mobile phone without battery.
Safety Precautions
Precautions for Potentially Explosive Atmospheres
 To protect your mobile phone from illegal use, take the security
measures as follows:
 Set PIN codes of the SIM card.
 Set handset lock code.
 Set call restrictions.
This section includes some important information on safe and efficient
operation. Please read this information before using the phone.
Operational Precautions
 Please use your phone properly. When making or receiving a call,
please hold your phone as holding a wireline telephone. Make sure
that the phone is at least one inch (about two point five centimeters)
from your body when transmitting.
 Do not touch the antenna when the phone is in use. Touching the
antenna area affects call quality and may cause the phone to operate
at a higher power level than needed.
 Some people may be susceptible to epileptic seizures or blackouts
when exposed to flashing lights, such as when watching television or
playing video games. If you have experienced seizures or blackouts,
or if you have a family history of such occurrences, please consult
your doctor before playing video games on your phone or enabling
a flashing-light feature on your phone. (The flashing-light feature is
not available on all products.)
 Keep the phone out of the reach of small children. The phone may
cause injury if used as a toy.
Precautions While Driving
 Please pay attention to the traffic safety. Check the laws and regulations
on the use of your phone in the area where you drive. Always obey them.
 Use hands-free function of the phone, if available.
Release: V1.0.0
079584500385
ZTE Plaza, Keji Road South, Hi-tech Industrial Park, Nanshan District,
Shenzhen, P. R. China
Postal Code: 518057
Website: http://www.zte.com.cn
ZTE CORPORATION Address:
The information in this manual is subject to change without notice. Every
effort has been made in the preparation of this manual to ensure accuracy
of the contents, but all statements, information, and recommendations
in this manual do not constitute a warranty of any kind, expressed or
implied. Please read the safety precautions carefully to ensure the correct
and safe use of your mobile phone. For detailed information, refer to the
section “Safety Precautions”.
Notice
ZTE and the ZTE logos are trademarks of ZTE CORPORATION.
Trademarks
Your mobile phone is made by ZTE CORPORATION.
No part of this manual may be reproduced or transmitted in any form or
by any means without prior written consent of ZTE CORPORATION.
All Rights Reserved
Copyright © 2009 ZTE CORPORATION
Legal Information
- 1 -
 Pull off the road and park before making or answering a call if
conditions require.
Precautions for Medical Devices and Facilities
 When using your phone near pacemakers, please always keep the
phone more than eight inches (about twenty centimeters) from the
pacemaker when the phone is switched on. Do not carry the phone in
the breast pocket. Use the ear opposite the pacemaker to minimize the
potential for interference. Switch off the phone immediately if necessary.
 Some phones may interfere with some hearing aids. In the event of
such interference, you may consult your hearing aids manufacturer
to discuss alternatives.
 If you use any other personal medical device, please consult the
manufacturer of your device to determine if it is adequately shielded
from RF energy.
 In those facilities with special demand, such as hospital or health
care facilities, please pay attention to the restriction on the use of
mobile phone. Switch off your phone if required.
Mobile Phone
 Please use original accessories or accessories approved by the phone
manufacturer. Using any unauthorized accessories may affect your
mobile phone’s performance, damage your phone or even cause
danger to your body and violate related local regulations about telecom
terminals.
 Turn off your phone before you clean it. Use a damp or anti-static
cloth to clean the phone. Do not use a dry cloth or electrostatically
charged cloth. Do not use chemical or abrasive cleaners as these
could damage the phone.
 As your mobile phone can produce electromagnetic field, do not
place it near magnetic items such as computer disks.
 Using the phone near electrical appliances such as TV, telephone,
radio and personal computer can cause interference.
 Do not expose your mobile phone to direct sunlight or store it in hot
areas. High temperatures can shorten the life of electronic devices..
- 2 -
通用直板彩屏英文使用手册(定稿)_090630.indd
1
 Switch off your phone prior to entering any area with potentially
explosive atmospheres, such as fueling areas, fuel or chemical
transfer or storage facilities.
 Do not remove, install, or charge batteries in such areas. Spark in
a potentially explosive atmosphere can cause an explosion or fire
resulting in bodily injury or even death.
 To avoid possible interference with blasting operations, switch off
your phone when you are near electrical blasting caps, in a blasting
area, or in areas posted “Turn off electronic devices.” Obey all signs
and instructions.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special,
incidental or consequential damages resulting from or arising out of
or in connection with using this product, whether or not ZTE had been
advised, knew or should have known the possibility of such damages.
The user should refer to the enclosed warranty card for full warranty
and service information.
Note: The pictures and icons shown in the manual are just schematic
drawings for function demonstration. If they are inconsistent with your
handset, please take your handset as the standard. If the inconsistency
exits in the manual because of the handset function updating, please
refer to the follow-up public information from ZTE CORPORATION.
Key Functions
Precautions for Electronic Devices
 Some electronic devices are susceptible to electromagnetic interference
sent by mobile phone if inadequately shielded, such as electronic
system of vehicles. Please consult the manufacturer of the device
before using the phone if necessary.
 Safety airbag, brake, speed control system and oil eject system
shouldn’t be affected by wireless transmission. If you do meet problems
above, please contact your automobile provider. Do not place your
phone in the area over an airbag or in the airbag deployment area.
Airbags inflate with great force. If a phone is placed in the airbag
deployment area and the airbag inflates, the phone may be propelled
with great force and cause serious injury to occupants of the vehicle.
 Please turn off your mobile phone at a refueling point, and the same
to the place where the use of two-way radio is prohibited.
Left soft key
Send key
Aircraft Safety
Battery Use
 Do not short-circuit the battery, as this can cause the unit to overheat
or ignite.
 Do not store battery in hot areas or throw it into fire. Otherwise, it
will cause explosion.
 Do not disassemble or refit the battery. Otherwise, it will cause liquid
leakage, overheating, explosion and ignition of the battery.
 Please store the battery in a cool dry place if you don’t use it for a
long period.
 The battery can be recharged for hundreds of times, but it will eventually
wear out. When the operating time (talk time and standby time) is
noticeably shorter than normal, it is time to replace it with a new one.
 Please stop using the charger and battery when they are damaged
or show evidence of aging.
 Return the worn-out battery to the provider or dispose of it in
accordance with environment regulations. Do not dispose of it in
household rubbish.
 Please use original batteries or batteries approved by the phone
manufacturer. Using any unauthorized battery may affect your
handset performance or may cause danger of explosion, etc.
Warning: If the battery is damaged, do not discharge it. If the leakage
does come into contact with the eyes or skin, wash thoroughly in clean
water and consult a doctor.
- 4 -
Right soft key
End/Power key
Alpha numeric keys
# key
* key
- 3 -
 Please turn off your mobile phone before the airplane takes off. In
order to protect airplane’s communication system from interference,
it is forbidden to use mobile phone in flight. Safety regulations require
you to have permission from a crew member to use your phone while
the plane is on the ground.
 If the mobile phone has the function of automatic timing power-on,
please check your alarm setting to make sure that your phone will
not be automatically turned on during flight.
Centre key
4-Way Navigation keys
Safety and General Use in Vehicles
- 5 -
Function
Left soft key
Description
Perform the function indicated at the left bottom of the screen.
Right soft key Perform the function indicated at the right bottom of the screen.
Centre key
Confirm actions and make selections.
4-Way
Navigation
keys
These keys (UP, DOWN, LEFT and RIGHT) allow for
navigation through menu options and quick accessing to
some function menus.
You can customize the fastkey settings of 4-Way Navigation
keys in the standby mode.
Send key
Dial a phone number or answer a call, or view the call history.
End/Power
key
Press to exit to the standby mode.
Hold to switch on/off the phone.
Alpha
Enter characters 0-9 and the alphabets from a-z.
numeric keys
Note: In this User Manual, “press a key” means to press the key and
release it, while “hold a key” means to press the key for at least two
seconds and then release it.
To lock/unlock the keypad, press the # key and then the * key.
Interface icons
Signal strength
Call diverting
Roaming
Vibration
Incoming message
Silent
Alarm clock set
Battery status
- 6 -
2009-10-13
14:37:32
Battery
What is a SIM card?
The lithium ion battery of the mobile phone can be immediately used
after unpacking.
Installing the battery
111 *Remove the battery cover.
222 Insert the battery by aligning the gold-colored contacts with the contacts
in the battery slot.
333 Push down the upper section of the battery until it clicks into place.
444 Replace the battery cover and close it gently until you hear a click.
Push down the battery
Removing the battery
111 Make sure that your mobile phone is switched off.
222 *Remove the battery cover.
333 Pull the battery up and remove it from the mobile phone.
Every mobile phone has a SIM card (Subscriber Identity Module). This
is a micro-chip that holds your personal information such as names and
phone numbers. Your phone won’t work without it. If you already have
contacts on your SIM card, they can be transferred in most cases.
How to charge the battery
Your phone is powered by a rechargeable battery. For maximum battery
performance, it is recommended that you first use up the battery power
and then charge it completely. A new battery’s full performance is achieved
only after three complete charge and discharge cycles.
ƒƒ Connect your travel adapter to the side of your mobile phone as
shown in the diagram.
Note: The side with arrow should be upright while connecting.
ƒƒ Connect the other end of the travel adapter to the mains socket.
ƒƒ If you charge the battery when the phone is switched off, the battery
indicator appears with the bars moving from right to left. If you charge
the battery when the phone is switched on, the battery indicator
appears with a lightning bolt.
ƒƒ When the battery is fully charged, disconnect the charger.
ƒƒ Input Words: In Eng mode, input any letter with a single key press.
Press each key only once for every letter. The word changes after
each key stroke. Predictive text input is based on a built-in dictionary.
When you have finished writing the word and it is correct, confirm
it by pressing the 0 key or the Centre key. If the word is incorrect,
press the Up/Down keys to view other matching words found in the
dictionary. Pressing the Navigation keys moves the cursor.
ƒƒ Input Digits: In 123 mode, press digit key once to input a digit. In
Eng mode, press the digit key, and select the number by pressing
the Navigation keys. In *Abc/abc/ABC mode, constantly press the
digit key until the number appears.
ƒƒ Input Symbol: Press the * key to enter a symbol. In *Abc/abc/ABC
mode, constantly press the 1 key till the required symbol (common
symbols) appears.
ƒƒ Selecting Template: Hold the * key to open Templates. Select the
required template.
ƒƒ Input Space: Press the 0 key to input space. It does not work in 123
mode.
ƒƒ Delete Character: Press the Right soft key to clear a character. Hold
the Right soft key to delete all characters and clear the display.
ƒƒ Move Cursor to Left or Right: Press the Left/Right navigation keys to
move the cursor to left or right.
*Note: Abc mode is only available for certain models.
How to add people to your Contacts
Pull up the battery
* Note: The correct way to remove the battery cover varies with the
model of the mobile phone. Please refer to the following diagrams.
- 7 -
- 9 -
Insert
Powering on/ off your phone
Make sure that your SIM card is in your mobile phone and that the battery
is charged.
Please hold the End/Power key to power on/off the phone. The phone
will automatically search for the network.
Writing text
Insert the SIM card
Pull out the SIM card
- 8 -
通用直板彩屏英文使用手册(定稿)_090630.indd
ƒƒ Change input mode: Press the # key to change the input mode (input
modes: Eng, *Abc, abc, ABC and 123).
ƒƒ Input Letters: In *Abc/abc/ABC mode, press the corresponding letter
key till the letter appears.
- 10 -
2
You can adjust various settings of your phone.
ƒƒ Phone settings: Select language, edit your own phone number, set
fastkey and select to turn on/off the automatic keypad locking function.
ƒƒ Display settings: Select your favorite wallpaper and adjust the screen’s
contrast and brightness.
ƒƒ Clock settings: Set date and time, and date format.
ƒƒ Security settings: Security features protect you from illegal use of your
phone and SIM card.
Note: You need to input the handset lock code to enter the security
settings interface. The default lock code is 1234.
How to set your alarm
ƒƒ Set alarm: Select Set alarm submenu, you can set the corresponding
features of the alarm according to instructions: alarm type (if required),
date, time, and ringtone.
ƒƒ List alarms: Select List alarms submenu, you can view, edit and delete
the alarm clocks settings. You can also enable or disable the alarms.
ƒƒ Clear all: Select Clear all to clear all the alarm clocks.
ƒƒ Define rest day: Select Define rest day to set or change rest days of
a week. Workday alarm will not ring on the defined rest day(s).
- 11 -
- 13 -
How to make and receive calls
You want a mobile phone that is sophisticated yet easy to use and here
it is in your hands! Naturally you are eager to start using it, but first you
need to insert the SIM card.
Insert the SIM card as follows:
ƒƒ Make sure that the phone is switched off and the charger is disconnected
from the phone.
ƒƒ Turn the phone over and remove the battery cover.
ƒƒ Remove the battery if it is already installed.
ƒƒ Hold your SIM card with the cut corner oriented as shown and then
slide it into the card holder with the gold-colored contacts facing
downward.
ƒƒ Replace the battery first.
ƒƒ Replace the battery cover.
How to set your phone
There are some numbers that you may want to call again and again, so
it makes sense to add these numbers to your contact list. You can then
access these numbers quickly and easily.
ƒƒ Enter Contacts menu.
ƒƒ Press the Left soft key [Options], and then select Add new contact.
ƒƒ Select to save the number to SIM card or Phone, and then enter the
contact’s phone number.
ƒƒ Press the Left soft key [OK] or the Centre key, then enter a name and
confirm by pressing the Left soft key [OK] or the Centre key again.
ƒƒ You can also save a number right after you’ve made or received a
phone call or a text message from someone who is not yet in your
contact list.
ƒƒ To delete someone from your contact list, first select the name, then
press the Left soft key [Options] and choose Delete.
How to insert the SIM card
444 Enter the recipient’s phone number or select from Contacts. Then
select OK to send the message.
Upon receiving a message, the mobile phone indicates with ringtone,
prompt, or a new message icon.
111 Press the Left soft key [Select] to open the new message. You can
also go to Inbox to read the message.
222 Use the Up/Down keys to read the message.
333 While the message is open, use the Left soft key [Options] to reply,
delete, or forward the message. You can also call back to the sender
or extract the sender’s number.
The most basic way to make a call is to input the number in the standby
mode and press the Send key. You can also make a call from the contact
list.
ƒƒ To call someone: Enter Contacts menu. Use the Up/Down keys to
find the name of the person you want to call. You can also type in
the first letter of the name of the person you want to call, and press
the Send key.
ƒƒ To receive a call, press the Send key.
ƒƒ To end a call, press the End/Power key.
Make sure that you are in an area with sufficient coverage to make calls.
The strength of the network signal is indicated on the Status Bar of the
screen.
How to send and receive messages
You can use your mobile phone to send and receive text messages.
111 Go to Menu→Messaging→New message.
222 Write your message. For more information on writing, see section
‘Writing text’.
333 Press the Left soft key [Options] and select Send to one to send the
message to one person.
To send to more than one person, select Send to contacts and select
the names from the contact list.
- 12 -
*WAP
The WAP browser feature on your phone allows you to view internet
content.
ƒƒ You can view the homepage when it has been set or input the website
address to view the web pages.
ƒƒ The current website addresses can be saved as bookmarks on your
phone.
ƒƒ You can set the features of WAP browser.
ƒƒ You can check the previously viewed web addresses and GPRS
information.
*FM Radio
With the radio, you can search for radio channels, listen to them, and
save them on your device. Note that the quality of the radio broadcast
depends on the coverage of the radio station in that particular area.
The wired headset works as an antenna, so always connect the headset
when using the radio. When you receive an incoming call while listening
to the radio, the radio will be turned off.
You can scan for channels automatically or tune them manually. The
channels can also be set by inputting valid frequencies.
To adjust the volume, press the Up/Down keys.
The channels can be stored in a channels list. Open the list to view the
information of the saved channels.
* Note: WAP and FM radio are only available for certain models.
- 14 -
2009-10-13
14:37:34
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising