ZTE | MF65 | User manual | ZTE MF65 User manual

ZTE MF65 User manual
ZTE MF65
Let’s go
Getting started with your device.
1
LEGAL INFORMATION
Getting to Know Your Device
Copyright © 2013 ZTE CORPORATION.
Appearance
All rights reserved.
The following figure is only for your reference. The actual product may be different.
No part of this publication may be excerpted, reproduced, translated or utilized
in any form or by any means, electronic or mechanical, including photocopying
and microfilm, without the prior written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to make
modifications on print errors or update specifications without prior notice.
Version No. : R1.1
Edition Time : 2.5.2013
NOTE:
Do not use the device in an enclosed environment or where heat dissipation is
poor. Prolonged work in such space may cause excessive heat and raise ambient temperature, which may lead to automatic shutdown of the device for your
safety. In the case of such event, cool the device in a well-ventilated place before turning on for normal use.
2
1.
2.
3.
4.
5.
6.
LED Indicators
Power Button
WPS Button
Micro USB Port
(U)SIM Card Slot
microSD Card Slot
NOTE: microSD logo
is a trademark of SD-3C, LLC.
3
Indicators
Indicator
Network
Wi-Fi
•
Status
Description
Red solid
Error status. Not registered to the mobile network, no (U)SIM card inserted or no network
service available.
Green solid
Registered to the mobile network.
Green blinking
Connected to the mobile network and data is
being transferred.
Blue solid
Wi-Fi is active.
Blue blinking
WPS is active.
LED light off
Wi-Fi is off or your device is in sleep mode.
Red solid/ blinking The battery is low. Please charge the battery.
Battery
3G Mode: Use your (U)SIM card to access the Internet.
Green blinking
The battery is being charged.
Green solid
The battery level is middle or high.
LED light off
Your device is in standby mode and not being
charged, or the battery is not inserted.
AP Station Mode: Your device will connect to other WLAN device (hotspot
device, wireless router, etc.) via Wi-Fi to access the Internet. The WLAN device has already connected to the Internet.
NOTE:
The subnets of your device and other WLAN device must be different.
•
Connection Scenario
Your device supports two methods to connect to the Internet and supports multiclients for surfing on the Internet at the same time. The following figure is only
for your reference.
4
5
Installing Your Device
3. Insert the microSD card if necessary.
1. Slide the back cover and remove it
2. Insert the (U)SIM card.
IMPORTANT: Your device does not support Micro/Nano SIM card or any other
nonstandard SIM cards. To avoid device damage, please do not use them or
any card holders.
6
4. Insert the battery.
7
5.
NOTE: Please set the client to obtain an IP address automatically referring to
the chapter “Configuring your PC”, and then the client will get an IP address like
“192.168.0.101”.
3. Select the SSID of your device, and then click Connect.
Close the back cover.
Connecting to Your Device
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search for the available
wireless networks.
NOTE: Please check the label on your device to get the default SSID.
4. Input the password, and then click Connect.
8
9
NOTE:
You may need to input the password for Wi-Fi connection. Please check the label on your device to get the default.
5. Wait a moment, and then the client will connect to your device successfully.
2. Power on your device.
3. The OS detects and recognizes new hardware and finishes the installation
automatically.
NOTE:
If the system does not launch installation automatically, you can run the installation program in path of My Computer > GP Modem.
4. Wait a moment, and then the client will connect to your device successfully.
Accessing the Internet
3G Mode
After the client connected to your device successfully, you can access the Internet in the Automatic or Manual mode. The default mode is Automatic.
Mode
Via USB Cable
Operations
Automatic
Your device will connect to the Internet automatically, and
your clients can surf on the Internet directly.
Manual
Log in the webGUI configuration page, and select Settings >
3G Settings > Network Select > WAN Connection Mode >
Manual, and then click Connect or Disconnect.
1. Connect to the device.
NOTE:
If you want to modify the detailed parameters of your device, please log in the
webGUI configuration page by visiting http://192.168.0.1 or http://m.home. The
default password is admin.
10
11
AP Station Mode
1. Log in the webGUI configuration page.
2. Select Settings > AP Setting.
3. Set the WLAN and WLAN mode, and then click Apply.
NOTE:
You need to set the WLAN On and select Wi-Fi Prior.
4. Connect to the WLAN device.
There are two methods for your reference.
u Input the WLAN device information in the WLAN Setting area, and then
click Apply.
u Click More, select this WLAN device which will be listed, and then click
Connect.
12
5. After the client connected to the WLAN device successfully, you can access
the Internet.
Configuring Your PC
Follow the following steps and figures for Windows XP to configure the Internet
Protocol for your Wi-Fi connection.
1. Right-click My Network Places, and then select Properties.
13
3. Select Internet Protocol(TCP/IP), and then click Properties.
2. Right-click Wireless Network Connection, and then select Properties.
14
4. Select Obtain an IP address automatically and Obtain DNS server address automatically, and then click OK to finish the configuration.
15
Warning and Notice
Using Your Device
•
To the Owner
•
•
•
•
•
•
•
Some electronic devices are susceptible to electromagnetic interference
sent by your device if inadequately shielded, such as the electronic system
of vehicles. Please consult the manufacturer of your device before using if
necessary.
Operating your device may interfere with medical devices like hearing aids
and pacemakers. Please always keep them more than 20 centimeters away
from such medical devices when they are turned on. Turn your device off if
necessary. Consult a physician or the manufacturer of the medical device
before using your device.
Be aware of the usage limitation when using your device at places such as
oil warehouses or chemical factories, where there are explosive gases or
explosive products being processed. Turn off your device if required.
The use of electronic transmitting devices is forbidden in aircrafts, at petrol
stations and in hospitals. Please observe and obey all warning signs and
switch off your device in these conditions.
Do not touch the inner antenna area if not necessary. Otherwise it will affect
your device’s performance.
Store your device out of the reach of little children. Your device may cause
injury if used as a toy.
Do not touch the metallic parts of your device so as to avoid a burn, when
your device is working.
•
•
•
•
•
•
Using Battery
•
•
•
•
•
16
Please use original accessories or accessories that are authorized. Using
any unauthorized accessories may affect your device’s performance, and
violate related national regulations about telecom terminals.
Avoid using your device near or inside metallic structures or establishments
that can emit electromagnetic waves. Otherwise it may influence signal reception.
Your device is not waterproof. Please keep it dry and store in a shady and
cool place.
Do not use your device immediately after a sudden temperature change. In
such case, it will produce dew inside and outside your device, so don’t use it
until it becomes dry.
Handle your device carefully. Do not drop, bend or strike it. Otherwise your
device will be damaged.
No dismantling by non-professionals and only qualified technicians can undertake repair work.
Operating temperature range of 0°C ~ +35°C and humidity range of 5% ~
95% are recommended.
Do not short-circuit the battery, as this can cause excessive heat and fire.
Do not store battery in hot areas or dispose of it in a fire to avoid explosion.
Do not disassemble or modify the battery.
When not using the battery for a long period, remove it from your device and
store it in a cool dry place.
Never use any charger or battery damaged or worn out.
17
•
Return the wear-out battery to the provider or put it in the appointed recycle
place. Do not put it in familial rubbish.
WARNING:
If the battery is broken, keep away from it. If it taints your skin, wash your skin
with abundant fresh water and ask doctor help if necessary.
Limited Warranty
•
This warranty does not apply to defects or errors in the Product caused by:
i. Reasonable abrasion.
ii. End User’s failure to follow ZTE’s installation, operation or maintenance
instructions or procedures.
iii. End User’s mishandling, misuse, negligence, or improper installation,
disassembly, storage, servicing or operation of the Product.
iv. Modifications or repairs not made by ZTE or a ZTE-certified individual.
v. Power failures, surges, fire, flood, accidents, actions of third parties or
other events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with third-party
products provided that such defects are due to the combined usage.
vii. Any other cause beyond the range of normal usage intended for the
Product.
End User shall have no right to reject or return the Product, or receive a refund
for the Product from ZTE under the above-mentioned situations.
• This warranty is End User’s sole remedy and ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed,
implied or statutory, including but not limited to the implied warranties of
merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law.
18
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special, incidental or
consequential damages resulting from or arising out of or in connection with using of this product, whether or not ZTE had been advised, knew or should have
known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product,
or any downtime cost.
Troubleshooting
Problem
Suggested Solution
•
Can not establish the
USB connection between
•
your device and PC.
•
•
Can not establish the Wi- •
Fi connection between
your device and client.
•
You need to install the software. Run the installation program in path of My Computer >
GP Modem.
If the driver of your device is abnormal, please
reinstall the software. You need to uninstall the
software first.
Make sure the Wi-Fi function is active.
Refresh network list and select the correct SSID.
Check the IP address to make sure your client
can obtain an IP address automatically in the Internet protocol (TCP/IP) properties.
Type the correct network key (Wi-Fi password)
when you connect to the device.
19
•
•
The client connected to
the device can not access
•
the Internet.
•
Make sure your (U)SIM card is available.
Change the location to find a place with good signal.
Check WAN Connection mode setting.
Contact with your service provider and confirm
your APN settings.
•
When I use AP Station
mode, the client cannot
•
access the Internet.
Make sure the other WLAN device has already
connected to the Internet.
Make sure that the subnet of your device and the
other WLAN device is different
•
Can not visit the webGUI
configuration page.
•
•
Enter the correct address. The default address is
http://192.168.0.1 or http://m.home.
Only use one network adapter in your PC.
Do not use any proxy server.
•
For the Wi-Fi connection password, please check
the label on the device.
The default password of the webGUI configuration page is admin.
If you changed the password and forgot the new
password, you need to restore the device to the
factory default settings.
About the password
•
•
For more assistance, please:
• Send E-mail to mobile@zte.com.cn
• Visit http://www.ztedevice.com
• Call Service Hotline: +86–755–26779999
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising