ZTE | MF65M | User manual | ZTE MF65M User manual

ZTE MF65M User manual
Quick Start Guide
Configuration page: http://mifi.orange.cm
Password: admin
Getting to Know Your Device
The following figure is for your reference only.
LED Indicators
Power Key
Charging/micro-USB Jack
(U)SIM Card Slot
microSDHC™ Card Slot
microSDHC logo
is a trademark of SD-3C, LLC.
Getting to Know Your Device
When the device is powered on, the following icons may be
lighting. For a description of the icons, refer to the following
Red solid
Error status. Not registered to
the mobile network, no (U)SIM
card inserted or no network
service available.
Green solid
Registered to the mobile
Connected to the mobile
network and data is being
Blue solid
Wi-Fi is active.
Blue blinking WPS is active.
Wi-Fi is off or your device is in
sleep mode.
Getting to Know Your Device
Blue solid
Red solid /
You have unread messages.
Blue blinking You have new messages.
No unread messages.
The battery is low. Please
charge the battery.
The battery is being charged
or in standby mode.
Green solid
The battery level is middle or
Your device is turn off and not
being charged, or the battery
is not inserted.
Getting to Know Your Device
Connection Scenarios
The Orange 3G hotspot Wi-Fi MF65M creates a personal
portable Wi Fi zone which allows several Wi-Fi enabled
devices (for example PCs, Apple® iPhone, iPad or iPod
touch, or mobile gaming devices such as Nintendo® DSi,
Android devices including smartphones and tablets) to
share a secure mobile internet connection.
The device can access the Internet and it allows multiple
clients to surf on the Internet at the same time, up to ten
terminal devices connection. The following figure is for your
reference only.
3G Mode: A (U)SIM card can be used to access the Internet.
Installing Your Device
1. Slide the back cover and remove it.
Do not remove the cover rudely.
2. Install a (U)SIM card to the (U)SIM card slot.
Your device does not support the micro-SIM card and
nano-SIM card or any other non-standard SIM cards. To
avoid damage to the device, do not use those cards or any
card holders.
Installing Your Device
3. Install the microSDHC card if necessary.
Installing Your Device
4. Install the battery.
5. Close the back cover.
Connecting to Your Device
Using Wi-Fi
1. Power on your device.
2. Make sure your computer or other client devices
have enabled Wi-Fi, and search for available wireless
Connecting to Your Device
Refer to your Wi-Fi-enabled client device manual for further
details on how to search for wireless networks. If you use
a computer, you need to set your computer to obtain an IP
address automatically.
3. Select the Wi-Fi name (SSID) of your device, and click
Connecting to Your Device
4. Enter the Wi-Fi password if necessary, and click OK.
Refer to the chapter Getting to Know the Wi-Fi SSID and
Password to get the default Wi-Fi SSID and password.
5. Wait until the client device is connected to your device
Connecting to Your Device
Using a USB Cable
1. Connect a computer to your device with a USB cable.
2. Power on your device. The operating system detects
and identifies new hardware, and automatically installs
the hardware.
NOTE: If the system does not automatically launch
installation, you can click the device installation icon in My
Computer to install the software.
3. Wait until the computer is connected to your device
Getting to Know the Wi-Fi SSID and
You can view the label on the device to get the default WiFi SSID and password. The label is on the top of the device
after you remove the back cover.
Wi-Fi SSID: Orange 3G Hotspot XXXXXX
Wi-Fi Key: 12345678
Logging in to the Mobile Hotspot
Configuration Page
1. Make sure the connection between your device and the
client device is correct.
2. Launch the Internet browser and enter or http:// mifi.orange.cm in the
address bar.
It is recommended that you use IE (7.0 or later), Firefox
(15.0 or later), Opera (10.0 or later), Safari (4.0 or later), or
Google Chrome (10.0 or later).
3. Enter the password to log in to the Mobile Hotspot
configuration page.
The default password is admin.
Changing the Wi-Fi SSID or Password
1. Log in to the Mobile Hotspot configuration page.
2. Select Settings > Wi-Fi Settings > Basic Settings.
3. Change the Network Name (SSID) or the Pass
Phrase ( Password).
4. Click Apply.
NOTE: If you forget the current password, press and
hold the Power button and the WPS button to restore to the
default password.
Accessing the Internet
After a client device is successfully connected to your
device, you can access the Internet in Automatic or
Manual mode. The default mode is Automatic.
Your device is automatically connected to
the Internet, and you can surf on the Internet
through the client.
1. Log in to the Mobile Hotspot
configuration page.
2. Select Settings > Network Settings >
Dial-up Settings > WAN Connection
Mode > Manual, and then click Apply.
3. Select Home, and click Connect or
To modify the parameters of your device, log in to the Mobile Hotspot configuration page.
Setting data limit
The data usage is measured by your device. Your carrier’
s data usage accounting may differ. You can check how
much data has been used during the time cycle you set,
and set the data limit and warning.
1. From the Web UI, click Information > Data Limit
Settings to set the data limit settings.
2. Click Enable and then you can set your data limit.
3. Click Apply to save your settings.
Configuring Your PC
The following procedure describes how to configure the
Internet Protocol in the Windows 7 operating system for
your Wi-Fi connection.
1. Right-click Network and select Properties.
2. Select Change adapter settings.
Configuring Your PC
3. Right-click Wireless Network Connection and select
Configuring Your PC
4. Select Internet Protocol Version 4 (TCP/IPv4), and
click Properties.
Configuring Your PC
5. Select Obtain an IP address automatically and
Obtain DNS server address automatically, and click
Warning and Notice
To the Owner
If inadequately shielded, some electronic devices, for
example, the electronic system of vehicles, may be
affected by the electromagnetic interference caused by
the device. Consult the manufacturers of such devices
before using the device if necessary.
Operating the device may interfere with medical
instruments such as hearing aids and pacemakers.
Always keep the device more than 20 centimeters
away from such medical instruments when your device
is powered on. Power off the device if necessary.
Consult a physician or the manufacturers of medical
instruments before using the device if necessary.
Be aware of the usage limitation when using the device
at places such as oil warehouses or chemical factories,
where there are explosive gases or explosive products
being processed. Power off the device if necessary.
Warning and Notice
Do not use electronic transmission devices in aircrafts,
at petrol stations or in hospitals. Observe and obey
all warning signs, and power off the device in these
Do not touch the inner antenna area unless necessary.
Otherwise the performance of the device may be
Do not use the device in an enclosed environment or
where heat dissipation is poor. Prolonged work in such
space may cause excessive heat and raise ambient
temperature, which may lead to automatic shutdown
of the device for your safety. In the case of such event,
cool the device in a well-ventilated place before turning
on for normal use.
Keep the device out of the reach of small children. The
device may cause an injury if used as a toy.
When the device is operating, do not touch the metallic
parts. Failing to do so may cause burns.
Warning and Notice
To the Users
Use original accessories or accessories that are
authorized. Using any unauthorized accessories may
affect the performance of the device and violate the
related national regulations about telecom terminals.
Avoid using the device near or inside metallic
constructions or establishments that can emit
electromagnetic waves, because signal reception may
be affected.
The device is not waterproof. Keep the device dry and
store it in a shady and cool place.
Do not use the device immediately after a sudden
temperature change, because dew may be generated
inside and outside the device. Do not use it until it
becomes dry.
Handle the device carefully. Do not drop, bend or strike
it. Otherwise the device may be damaged.
Only qualified personnel can dismantle and repair the
Warning and Notice
An operating temperature between 0°C and +40°C and
humidity between 5% and 95% are recommended.
Using Battery
Do not short-circuit the battery, as this can cause
excessive heat and fire.
Do not store battery in hot areas or dispose of it in a
fire to avoid explosion.
Do not disassemble or modify the battery.
When not using the battery for a long period, remove it
from your device and store it in a cool dry place.
Never use any charger or battery damaged or worn out.
Return the wear-out battery to the provider or put it in
the appointed recycle place. Do not put it in familial
If the battery is broken, keep away from it. If it taints your
skin, wash your skin with abundant fresh water and ask
doctor help if necessary.
Warning and Notice
Limited Warranty
This warranty does not apply to defects or errors in the
product caused by:
i. Reasonable abrasion.
ii. End users’ failure to follow ZTE’s installation,
operation or maintenance instructions or
iii. End users’ mishandling, misuse, negligence,
or improper installation, disassembly, storage,
servicing or operation of the product.
iv. Modifications or repairs not provided by ZTE or a
ZTE-certified individual.
v. Power failures, surges, fire, flood, accidents, and
actions of third parties or other events outside ZTE’
s reasonable control.
vi. U s a g e o f t h i r d - p a r t y p r o d u c t s o r u s a g e i n
conjunction with third-party products if such defects
are due to the combined usage.
Warning and Notice
vii. Any other cause beyond the range of normal usage
intended for the product.
End users have no right to reject or return the product, or
receive a refund for the product from ZTE under the abovementioned situations.
This warranty is end users’ sole remedy and ZTE’s sole
liability for defective or nonconforming items, and is in lieu
of all other warranties, expressed, implied or statutory,
including but not limited to the implied warranties of
merchantability and fitness for a particular purpose, unless
otherwise required under the mandatory provisions of the
Warning and Notice
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect,
special, incidental or consequential damages resulting from
or arising out of or in connection with using of this product,
no matter whether or not ZTE had been advised, knew or
should have known of the possibility of such damages,
including, but not limited to lost profits, interruption of
business, cost of capital, cost of substitute facilities or
product, or any downtime cost.
Copyright © 2015 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced,
translated or utilized in any form or by any means,
electronic or mechanical, including photocopying and
microfilm, without the prior written permission of ZTE
The manual is published by ZTE Corporation. We reserve
the right to make modifications on print errors or update
specifications without prior notice.
Version No.: R1.0
Edition Time: March 17, 2015
Manual No.:079584507213
The connection
between your
device and a PC
through a USB
cable cannot be
Recommended Action
The connection
between your
device and a
client through
Wi-Fi cannot be
Install the software, and run the
installation program in the path of
My Computer.
If the driver of your device is
abnormal, reinstall the software.
You need to uninstall the software
Ensure that the Wi-Fi function is
Refresh the network list and select
the correct SSID.
Check the IP address, and ensure
that your client can automatically
obtain an IP address.
Enter the correct network key (WiFi password) when you connect
the client to your device.
Recommended Action
The client
connected to the
device cannot
access the
The Mobile
page cannot be
Ensure that your (U)SIM card is
Change the location and find a
place with good signal.
Check the settings of the WAN
connection mode.
Contact your service provider and
confirm your APN settings.
Enter the correct address.
The default address is or http:// mifi.
Use only one network adapter in
your PC.
Do not use any proxy server.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF