ZTE | MF65 | User manual | ZTE MF65 User manual

ZTE MF65 User manual
Getting to Know Your Device
The following figure is only for your reference. The actual product may be
Let’s go
Getting started with your device.
Copyright © 2014 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in
any form or by any means, electronic or mechanical, including photocopying and
microfilm, without the prior written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to make
modifications on print errors or update specifications without prior notice.
Version No. : R1.1
Edition Time : 5.30 2014
Do not use the device in an enclosed environment or where heat dissipation is
poor. Prolonged work in such space may cause excessive heat and raise ambient
temperature, which may lead to automatic shutdown of the device for your safety.
In the case of such event, cool the device in a well-ventilated place before turning
on for normal use.
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
3. Insert the microSDHC card if necessary.
Blue solid
Wi-Fi is active.
Blue blinking
WPS is active.
LED light off
Wi-Fi is off or your device is in sleep mode.
Red solid/
The battery is low. Please charge the battery.
Green blinking
The battery is being charged.
Green solid
The battery level is middle or high.
LED light off
Your device is in standby mode and not being
charged, or the battery is not inserted.
Via Wi-Fi
NOTE: microSDHC™ logo
4. Insert the battery.
is a trademark of SD-3C, LLC.
Red solid
Green solid
Registered to the mobile network.
Green blinking
Connected to the mobile network and data is
being transferred.
2. Power on your device.
3. The OS detects and recognizes new hardware and finishes the
installation automatically.
If the system does not launch installation automatically, you can run the
installation program in path of My Computer > ZTEMODEM.
4. Wait a moment, and then the client will connect to your device
3G Mode
After the client connected to your device successfully, you can access the
Internet in the Automatic or Manual mode. The default mode is Automatic.
AP Station Mode: Your device will connect to other WLAN device
(hotspot device, wireless router, etc.) via Wi-Fi to access the Internet.
The WLAN device has already connected to the Internet.
The subnets of your device and other WLAN device must be different.
1. Connect to the device.
Accessing the Internet
5. Close the back cover.
Error status. Not registered to the mobile
network, no (U)SIM card inserted or no
network service available.
You may need to input the password for Wi-Fi connection. Please check the
label on your device to get the default.
5. Wait a moment, and then the client will connect to your device
NOTE: Please set the client to obtain an IP address automatically referring to
the chapter “Configuring your PC”, and then the client will get an IP address
like “”.
3. Select the SSID of your device, and then click Connect.
2. Insert the (U)SIM card.
WARNING: Your device does not support Micro/Nano SIM card or any other
nonstandard SIM cards. To avoid device damage, please do not use them or
any card holders.
Via USB Cable
Installing Your Device
1. Slide the back cover and remove it
Your device supports two methods to connect to the Internet and supports
multi-clients for surfing on the Internet at the same time. The following figure
is only for your reference.
• 3G Mode: Use your (U)SIM card to access the Internet.
LED Indicators
Power Button
WPS Button
Micro USB Port
(U)SIM Card Slot
microSDHC Card Slot
Please check the label on your device to get the default SSID.
4. Input the password, and then click Connect.
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search for the available
wireless networks.
Connection Scenario
Connecting to Your Device
Your device will connect to the Internet automatically, and
your clients can surf on the Internet directly.
Log in the webGUI configuration page, and select Settings
> 3G Settings > Network Select > WAN Connection
Mode > Manual, and then click Connect or Disconnect.
If you want to modify the detailed parameters of your device, please log in
the webGUI configuration page by visiting or http://m.home.
The default password is admin.
2. Right-click Wireless Network Connection, and then select Properties.
4. Select Obtain an IP address automatically and Obtain DNS server
address automatically, and then click OK to finish the configuration.
AP Station Mode
1. Log in the webGUI configuration page.
2. Select Settings > AP Setting.
3. Set the WLAN and WLAN mode, and then click Apply.
You need to set the WLAN On and select Wi-Fi Prior.
5. After the client connected to the WLAN device successfully, you can
access the Internet.
Using Your Device
3. Select Internet Protocol(TCP/IP), and then click Properties.
Configuring Your PC
Follow the following steps and figures for Windows XP to configure the
Internet Protocol for your Wi-Fi connection.
1. Right-click My Network Places, and then select Properties.
Warning and Notice
4. Connect to the WLAN device.
There are two methods for your reference.
Input the WLAN device information in the WLAN Setting area, and
then click Apply.
Click More, select this WLAN device which will be listed, and then
click Connect.
To the Owner
Be aware of the usage limitation when using your device at places such
as oil warehouses or chemical factories, where there are explosive gases
or explosive products being processed. Turn off your device if required.
The use of electronic transmitting devices is forbidden in aircrafts, at
petrol stations and in hospitals. Please observe and obey all warning
signs and switch off your device in these conditions.
Do not touch the inner antenna area if not necessary. Otherwise it will
affect your device’s performance.
Store your device out of the reach of little children. Your device may
cause injury if used as a toy.
Do not touch the metallic parts of your device so as to avoid a burn,
when your device is working.
Some electronic devices are susceptible to electromagnetic interference
sent by your device if inadequately shielded, such as the electronic
system of vehicles. Please consult the manufacturer of your device
before using if necessary.
Operating your device may interfere with medical devices like hearing
aids and pacemakers. Please always keep them more than 20
centimeters away from such medical devices when they are turned
on. Turn your device off if necessary. Consult a physician or the
manufacturer of the medical device before using your device.
Please use original accessories or accessories that are authorized. Using
any unauthorized accessories may affect your device’s performance, and
violate related national regulations about telecom terminals.
Avoid using your device near or inside metallic structures or
establishments that can emit electromagnetic waves. Otherwise it may
influence signal reception.
Your device is not waterproof. Please keep it dry and store in a shady
and cool place.
Do not use your device immediately after a sudden temperature change.
In such case, it will produce dew inside and outside your device, so don’t
use it until it becomes dry.
Handle your device carefully. Do not drop, bend or strike it. Otherwise
your device will be damaged.
No dismantling by non-professionals and only qualified technicians can
undertake repair work.
Operating temperature range of 0 ºC ~ +35 ºC and humidity range of 5%
~ 95% are recommended.
Using Battery
Do not short-circuit the battery, as this can cause excessive heat and
• Do not store battery in hot areas or dispose of it in a fire to avoid
• Do not disassemble or modify the battery.
• When not using the battery for a long period, remove it from your device
and store it in a cool dry place.
• Never use any charger or battery damaged or worn out.
• Return the wear-out battery to the provider or put it in the appointed
recycle place. Do not put it in familial rubbish.
If the battery is broken, keep away from it. If it taints your skin, wash your
skin with abundant fresh water and ask doctor help if necessary.
Limited Warranty
This warranty does not apply to defects or errors in the Product caused
i. Reasonable abrasion.
ii. End User ’s failure to follow ZTE’s installation, operation or
maintenance instructions or procedures.
iii. End User’s mishandling, misuse, negligence, or improper installation,
disassembly, storage, servicing or operation of the Product.
iv. Modifications or repairs not made by ZTE or a ZTE-certified
v. Power failures, surges, fire, flood, accidents, actions of third parties
or other events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with third-party
products provided that such defects are due to the combined usage.
vii. Any other cause beyond the range of normal usage intended for the
End User shall have no right to reject or return the Product, or receive a
refund for the Product from ZTE under the above-mentioned situations.
This warranty is End User’s sole remedy and ZTE’s sole liability for
defective or nonconforming items, and is in lieu of all other warranties,
expressed, implied or statutory, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose, unless
otherwise required under the mandatory provisions of the law.
Suggested Solution
• Make sure your (U)SIM card is available.
• Change the location to find a place with good
• Check WAN Connection mode setting.
• Contact with your service provider and confirm
your APN settings.
Limitation of Liability
The client connected
to the device can not
access the Internet.
ZTE shall not be liable for any loss of profits or indirect, special, incidental or
consequential damages resulting from or arising out of or in connection with
using of this product, whether or not ZTE had been advised, knew or should
have known of the possibility of such damages, including, but not limited to
lost profits, interruption of business, cost of capital, cost of substitute facilities
or product, or any downtime cost.
• Make sure the other WLAN device has
When I use AP Station
already connected to the Internet.
mode, the client cannot
• Make sure that the subnet of your device and
access the Internet.
the other WLAN device is different
Suggested Solution
Can not establish
the USB connection
between your device
and PC.
• You need to install the software. Run the
installation program in path of My Computer
• If the driver of your device is abnormal, please
reinstall the software. You need to uninstall
the software first.
Can not establish
the Wi-Fi connection
between your device
and client.
• Make sure the Wi-Fi function is active.
• Refresh network list and select the correct
• Check the IP address to make sure your client
can obtain an IP address automatically in the
Internet protocol (TCP/IP) properties.
• Type the correct network key (Wi-Fi password)
when you connect to the device.
Can not visit the
webGUI configuration
• Enter the correct address. The default address
is or http://m.home.
• Only use one network adapter in your PC.
• Do not use any proxy server.
About the password
• For the Wi-Fi connection password, please
check the label on the device.
• The default password of the webGUI
configuration page is admin.
• If you changed the password and forgot the
new password, you need to restore the device
to the factory default settings.
For more assistance, please:
• Send E-mail to mobile@zte.com.cn
• Visit http://www.ztedevice.in
• Call Service Hotline: 1800-103-1900
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF