ZTE MF60 User manual
ZTE MF60 is a mobile hotspot device that allows you to connect to the internet using either a USB cable or Wi-Fi. It supports 3G and 2G networks and can be used to send and receive SMS messages. The device has a built-in battery and can be charged using a USB cable or adapter. You can also insert a microSD card to expand the storage capacity. With its compact size and portability, the ZTE MF60 is a convenient way to stay connected while on the go.
PDF
Download
Document
Advertisement
Advertisement
LEGAL INFORMATION Introduction Copyright © 2012 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. ZTE MF60 is a 3G/2G mobile hotspot device, working in GSM/GPRS/EDGE/ WCDMA/HSPA/HSPA+ network. The client devices could connect to it via USB or Wi-Fi interface. The device supports data and SMS services, enabling you to communicate anytime and anywhere. This guide provides the instructions on how to install and get started with the product. For information about connection of services, please consult your service provider. Getting to Know Your Device The following figure shows the appearance of the device, it is only for your reference. The actual device may be different. 4. Screen It indicates the network type, signal strength, battery, Wi-Fi, etc. 5. External Antenna Connector It is used to connect an external antenna to enhance the signal strength. 6.Charger/USB port • • Hardware Installation Inserting SIM Card and Battery 1. Use the thumb catch at the bottom of the device to open the battery cover. 2. Insert the SIM card into the SIM card holder. Note: To restart device and restore to the factory default settings, hold the WPS and Power buttons simultaneously until the screen turns off, and then release the buttons. Indicator Icon Interface and Buttons 1.Power Hold the Power button to switch on/off the device. 2.Memory card slot It is where you insert the memory card (microSD card). (microSD card) ZTE CORPORATION NO. 55, Hi-tech Road South, ShenZhen, P.R.China Postcode: 518057 Tel: +86-755-26779999 URL: http://www.zte.com.cn E-mail: [email protected] 1 3.WPS 2 This button is used to start/end Wi-Fi Protected Setup authentication process and enable/disable the Wi-Fi function. • Hold it for 3 seconds to activate the WPS function. • When the WPS function is available, press it to deactivate the WPS function. • Press it to enable/disable Wi-Fi function. • Press it twice continuously to display the current SSID and Wi-Fi password on the screen. 3 Working Mode Mixed Mode: Connect to the device with the above two connection methods. Your device supports three working modes. For the client, we only use PC or laptop as the example in this document. USB Mode: Connect to the device with the USB cable. 3. Close the microSD cover. Notes: is a trademark of SD Card Association. Switching On/Off Your Device Indication Network type. 2G or 3G icon will appear on the screen according to the network being connected. Quick Start Guide Pull the microSD cover gently out of the card slot. Insert the microSD card into the microSD slot. The following picture shows the correct inserting direction. You will hear a click when the microSD card locks in place. microSD Wi-Fi Mode: Connect to the device via Wi-Fi. Notes: You need to check your Wireless Network Connection. Set the client to obtain an IP address automatically in the Internet protocol (TCP/IP) properties, and the client will get an IP address like “192.168.0.100”. 3. Select the SSID of your device, and then click Connect. 3. Insert the battery as shown with the contacts located against the metal springs, and press the battery down into the case. 4. Line the battery cover up correctly and press gently to close the case. Connect to the Internet automatically. Connect to the Internet manually. Charging Your Device Via USB Cable • Connect your device and the client with the USB cable. • Power on your device. • Follow the system prompts to complete the software installation. Notes: • If the system does not launch installation automatically, you can run the installation program in path of My Computer > AIRTEL HOTSPOT. • The driver of your device will be installed at the same time. • After the installation, the system will create a shortcut icon on your desktop and an Airtel Internet program group in the Start - Programs menu. The connection between your device and the client will be established successfully a moment later. Via Wi-Fi 1. Power on your device directly. It will take 1~2 minutes to initialize. 2. Use your normal Wi-Fi application on the client to search the available wireless network. You can charge your device by using USB cable or adapter. 1. Insert the charger lead carefully with the plug arrow facing the bottom of the device. 2. The plug only fits one way. Do not use excessive force to insert the plug. 3. Make sure the plug is the right way round and lined up correctly. Insert it gently. Roaming network indication. New message received. Wi-Fi Status and number of the connecting users. Battery power indication. 4 5 6 Notes: If you want to connect to the Internet by using Wi-Fi mode, make sure that the client supports the Wi-Fi function. The following picture is the application example. All of the client devices can surf on the Internet at the same time. Establishing a Connection Between Your Device and the Client Hold the Power button to switch on/off the device. Notes: The device is powered on when the screen lights up. Network signal strength. ZTE MF60 1. 2. Charge your device. Connect the client to your device via USB cable. When the device is powered on, the following icons will appear on the screen, with the corresponding indicates listed in the table below: Version No. : 1.0 Edition Time: 05-2012 Manual No.: 079584504594 Inserting microSD Card 7 8 Notes: • There will be a pop-up window to require the password. Check the label on your device to gain the SSID and preset password information. • AIRTEL_XXXXXX is the SSID(Service Set Identifier) of your device. XXXXXX varies from device to device. 4. After a few moments, the connection between your device and the client will be established successfully. Accessing the Internet 1. 2. 3. Switch on the device. Establish a connection between your device and the client. After successfully establishing the connection, you can access the Internet in the Automatic or Manual mode. Notes: You can select the WAN connection mode by clicking Settings >3G Settings. 9 Quick Setup Accessing the WebGUI Configuration Page 1. 2. 3. After logging in, select Settings > Quick Settings, and then the Quick Setup wizard appears. Make sure the connection between your device and the client is established. Check your internet settings to make sure no proxy servers are defined. Launch the internet browser and enter http://192.168.0.1 or http://m.home in the address bar. And you can also double-click on your desktop to access the page. Notes: It is recommended that you use IE (7.0 or later), Firefox (3.0 or later), Opera (10.0 or later), Safari (4.0 or later), Chrome (10.0 or later). 4. The login page appears as follows. The wizard will show you how to set up the gateway in the safe way. Notes: The parameter settings may have been preset by your service provider, and you will enjoy your Internet service directly. Please contact your service provider for details if you want to do some modification. WAN Connection View the information of WAN, WLAN and Device. Input the case-sensitive default password “admin”, and then click Login to access the WebGUI Configuration page. Notes: • Do not put anything on the top of your device. Do not lay devices to overlap each other when using. • The device takes 1~2 minutes to initialize, and attach to the network. Notes: The SIM card will be locked if you enter wrong PIN code consecutively for three times. If you want to modify the PIN Status or change the PIN code, please select Settings > Advanced > PIN Manage to do the actions. After logging in, select Settings > 3G Settings, and you can choose the WAN Connection Mode according to your requirement. Select Settings > 3G Settings Select WAN Connection Mode, Band Selection Mode or change APN Setting. Select Settings > Wi-Fi Settings View the current station list, change the basic wireless network settings, choose security mode, and perform the WPS configuration. Select Settings > Advanced Restore your device to the factory default settings, manage PIN, set the LAN interface configuration, or change the Administrator Settings. Select Settings > Firewall Set the Mac/IP/Port Filtering, Port Forwarding or the System Security configuration. Notes: Make sure that you can remember the new password if you change the login password by selecting Settings > Advanced > Management. Please restore the device to the factory default settings in case you forget the new password. To do this, hold the WPS and Power buttons simultaneously until the screen turns off, and then release the buttons. Disconnecting from the Internet 1. Click button in the WebGUI Configuration page. 2. Click Disconnect button . Phonebook This function allows you to store contacts to your device or SIM card. After logging in, select Phonebook, add a new contact by clicking Add New, and perform operations to the contact in the Device or SIM Card. SMS 10 Select SMS > New Message Send or save SMS. Select SMS > Device Operate the SMS in your device. Select SMS > SIM Card Operate the SMS in your SIM card. Select SMS > SMS Settings Set the SMS configuration. Airtel Services Settings 11 12 Notes: Turning off the device can also terminate the Internet connection. 13 • 14 Usage of WPS If your client device supports WPS, you need not to input the password manually after WPS has been available. Please do the following: 1. Start up your device. 2. Launch the client device connected to your device. 3. Enable the WPS function of your device. 4. Enable the WPS function of the client. Sleep Mode In anyone of the two conditions below your device will enter the sleep mode: • After powering your device on without USB connection, once no user connects to the device within 10 minutes and no action is performed to the device. Or you press the WPS button, the device will enter the sleep mode. In the sleep mode, the Wi-Fi function will be disabled. • With USB connection, once the device is in the idle status for 10 minutes, or the WPS button is pressed manually, the Wi-Fi function will be disabled, and then unplug the USB cable, the device will enter the sleep mode. To wake up your device, press any button or connect your device and PC with the USB cable to wake up the device. 15 • • • • Some electronic devices are susceptible to electromagnetic interference sent by your device if inadequately shielded, such as the electronic system of vehicles. Please consult the manufacturer of your device before using if necessary. Operating of laptop and desktop PCs and your device may interfere with medical devices like hearing aids and pacemakers. Please always keep them more than 20 centimeters away from such medical devices when they are turned on. Turn your device off if necessary. Consult a physician or the manufacturer of the medical device before using your device. Be aware of the usage limitation when using your device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Turn off your device if required. The use of electronic transmitting devices is forbidden in aircrafts, at petrol stations and in hospitals. Please observe and obey all warning signs and switch off your device in these conditions. Do not touch the inner antenna area if not necessary as it may affect your device’s performance. Store your device out of the reach of little children. Your device may cause injury if used as a toy. Do not touch the metallic parts of your device so as to avoid a burn, when your device is working. Using Your Device • • • • • • To the Owner • This function allows you to view, send and receive short messages. After logging in, select SMS, and you can do the following operations. PIN Code Verification After logging in, select Settings, and you can do the following operations. After logging in, select Status to check the basic and network information. Warning and Notice • After logging in, select Airtel Services, and you can check your balance, recharge your account, etc. For the detailed information, please ask your service provider. If the PIN code of your SIM card is enabled, you will need to input the PIN code when you login at the first time. Status Please use original accessories or accessories that come with the device. Using any unauthorized accessories may affect your device’s performance, and violate related national regulations about telecom terminals. Avoid using your device near or inside metallic structures or establishments that can emit electromagnetic waves as it may influence signal reception. Your device is not waterproof. Please keep it dry and store in a shady and cool place. Do not use your device immediately after a sudden temperature change. In such case, it will produce dew inside and outside your device, so don’t use it until it becomes dry. 16 • Handle your device carefully. Do not drop, bend or strike it. Otherwise your device will be damaged. No dismantling by non-professionals and only qualified technicians can undertake repair work. Operating temperature range of 0 °C ~ +35 °C and humidity range of 5% ~ 95% are recommended. Using Battery • • • • Do not short-circuit the battery, as this can cause excessive heat and fire. Do not store battery in hot areas or dispose of it in a fire to avoid explosion. Do not disassemble or modify the battery. When not using the battery for a long period, remove it from your device and store it in a cool dry place. • Never use any charger or battery damaged or worn out. • Return the wear-out battery to the provider or put it in the appointed recycle place. Warning: If the battery is broken, keep away from it. If it taints your skin, wash your skin with fresh water and seek medical attention if necessary. Limited Warranty • This warranty is End User’s sole remedy and ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law. Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. How to Get Help You can get Help by: • Sending E-mail to [email protected] • Visiting http://www.zte.com.cn • Calling Service Hotline: +86–755–26779999 • This warranty does not apply to defects or errors in the Product caused by: i. Reasonable abrasion. ii. End User’s failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii. End User’s mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the Product. iv. Modifications or repairs not made by ZTE or a ZTE-certified individual. v. Power failures, surges, fire, flood, accidents, actions of third parties or other events outside ZTE’s reasonable control. vi. Usage of third-party products, or usage in conjunction with third-party products provided that such defects are due to the combined usage. vii. Any other cause beyond the range of normal usage intended for the Product. End User shall have no right to reject or return the Product, or receive a refund for the Product from ZTE under the above-mentioned situations. 17 18 ">

Public link updated
The public link to your chat has been updated.
Advertisement